Search Results

Search found 14483 results on 580 pages for 'css reset'.

Page 460/580 | < Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >

  • Replacing compiz/metacity with openbox reduces workspaces to 1

    - by Brian
    I like to use the GNOME desktop, but I prefer to replace its window manager with openbox, with 4 workspaces. However, when I run openbox --replace, the number of workspaces available drops to 1. If I go into obconf, workspaces is still configured to be 4 (~/.config/openbox/rc.xml shows the same). I can get the workspaces to reappear by changing the value in obconf to anything else, and then back to 4. I have just been dealing with this problem since Ubuntu 9.04 (now up to 10.10) since I don't reboot very often. But it's really annoying to have to reset my workspaces whenever I do have to reboot. Changing the value in rc.xml and running openbox --reconfigure does not seem to have any effect. So what is obconf doing that I'm not (sends a dbus message perhaps [EDIT: watching with dbus-monitor I see no messages when changing the workspaces value in obconf])? I was hoping there would be a cleaner way to change the window manager than just running openbox --replace at login. So my questions are: Is there a better way to specify an alternate window manager (i.e. a way that doesn't cause the workspaces to break)? If not, how can I automatically set the number of workspaces back to 4? Update: I finally got around to trying what I commented on MrShunz's answer (adding WINDOW_MANAGER=/usr/bin/openbox to ~/.gnomerc). But the effect is the same as openbox --replace.

    Read the article

  • So who decided VGA cables should be symetrical ? [closed]

    - by mgb
    < rant So who decided that VGA cables should be the same gender connector at both ends? I just spent an hour trying to fix a server that would apparently boot but wouldn't display any post messages - I needed to change some bios settings. The monitor gives me a helpful error message - "unable to display this resolution". Wondering how it can't show simple VGA res, I reset the bios, when that doesn't work I remove the BIOS battery. The system is in a rack with a keyboard and monitor mounted 6ft away - with the cable running through the normal waist thick rats nest of wiring of wiring. The monitor worked with another system, so it and the VGA cable are good, I brought in another monitor and tried that - still nothing. Eventually I ripped the rack apart to discover that the other end of the VGA connector I was trying to plug into the server was actually plugged into another server box ! And the second monitor I was testing was plugged into the first monitor. An error message like - "I'm actualy plugged into another monitor stupid" - would be useful. So would having a connector with a male end and a female end. < end rant - thank you

    Read the article

  • Setting up port forwarding for web server

    - by reyjavikvi
    This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

    Read the article

  • How can I update generic non-pnp monitor?

    - by njk
    Background I've been running a KVM switch with my monitor at 1920 x 1080 over VGA for over a year. Did a Windows Update on 12/11/12 which did the following: Update for Windows 7 for x64-based Systems (KB2779562) Security Update for Windows 7 for x64-based Systems (KB2779030) Cumulative Security Update for Internet Explorer 8 for Windows 7 for x64-based Systems (KB2761465) Windows Malicious Software Removal Tool x64 - December 2012 (KB890830) Security Update for Windows 7 for x64-based Systems (KB2753842) Security Update for Windows 7 for x64-based Systems (KB2758857) Security Update for Windows 7 for x64-based Systems (KB2770660) After a restart, my extended monitor was dark. I attempted to reset the extended display configuration, and noticed my monitor was being detected as a Generic Non-PnP Monitor: I uninstalled, downloaded new, and re-installed display drivers. Nothing. I attempted to unplug my monitor from the power for 15 minutes. Nothing. I followed some of the suggestions on this thread; specifically DanM's which suggested to create a new *.inf file and replace that in Device Manager. Device Manager said the "best driver software for your device is already installed". The only thing that works is when the monitor is directly attached to the laptop. This obviously is not what I want. My thought is to somehow remove the Generic Non-PnP Monitor from registry. How would I accomplish this and would this help? Any other suggestions? Relevant Hardware ASUS VE276 Monitor TRENDnet 2-Port USB KVM Switch (TK-207K) HP Laptop w/ ATI Radeon HD 4200 Screens

    Read the article

  • Microsoft Access: computer freezes when user tries to update record

    - by CarlF
    A colleague and I have developed an Access 2003 database which is used throughout our department. Currently about four dozen people do data entry using one of two very similar forms. If 47 of us use them, they work perfectly. If Mr. 48 clicks the "Save" button, Windows XP freezes and a hard reset is needed. The problem has to be on his specific computer (Dell latitude D630) and not in the code because this problem only affects him. Complicating the matter: I don't work for IS, and this project is not supported by IS. If I'm going to get our tech support to fix the problem I had better be able to explain exactly what to do and how to do it, because they aren't going to invest any resources. I don't even have admin rights on the computer (and neither does its regular user). I've asked him to bring his laptop the next time he visits my building. (Just to make matters worse, he doesn't usually work in the same location as me or the other developer.) Any suggestions on debugging the problem? My first try will be to uninstall and reinstall Office, which I can do using corporate utilities without being admin. Note: yes, those are old versions of Office and Windows. We expect to upgrade later this year.

    Read the article

  • Windows Photo Viewer can't open this picture because you don't have the correct permissions to access the file location

    - by Software Monkey
    My system in Windows 7 and fully up to date with all patches and options (except for Microsoft Silverlight, which I refuse to install). I get this error whenever I try to open an image using Windows Photo Viewer, such as when previewing from Explorer or when opening an image attachment to an email. I have already verified correct permissions to the file and all folders in the path. The strange thing is that every other program I have seems to open the images fine, including "Slideshow" from Windows Explorer. Even more strange, in WPV there is an "Open" menu that lists the other programs for images including GIMP and MS Paint and they open the very file that WPV is complaining about just fine. That should eliminate permissions as being the problem, especially since (logically at least) they are read/write while WPV is read-only. I have even edited and saved the images that WPV does not open. I am out of ideas, and searching for answer on the Web has resulted only in the same tired repitition of some flavor of "take ownership and reset permissions for the entire drive", which I have already done. And which is counter-indicated by the fact that only Windows Photo Viewer seems to have a problem. The one thing which is slightly unusual is that for normal files they are all on a second HDD mounted into C:, however for email attachments the temporary folder is C:\Temp\, which is directly on that drive.

    Read the article

  • Setting up self signed cert and CA [plesk / linux]

    - by microchasm
    I'm about ready to give up and do a clean wipe of this machine and start over with ISPConfig or some other variant. I installed Plesk on this machine to help with some of the handiwork. It is the free version (single domain); I don't need it for much. It's nice, though, to use to set up db's email, etc. Anyway, I would like to set it up as a CA (which I can add to users' trusted root servers to alleviate those warnings). It seems like Plesk does all it can to obfuscate where things are. Despite trying to find the conf files, and crt/pem/key etc. I am (5 hours later) now left with a machine that won't even get to the ssl page. The browser will sit there, until a 'connection reset' error comes up. In error_log, I get messages saying CN doesn't match server name -- which it does. ssl_error_log: [Thu May 13 16:02:14 2010] [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) [Thu May 13 16:12:19 2010] [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) not very helpful. If anyone has any experience, and/or recommendations (including other software), I'd be much obliged. NB RHEL5; 1 domain, 3 subdomains; everything local only. Thanks.

    Read the article

  • How can i export a folder of Firefox Bookmarks into a text file

    - by Memor-X
    I want to clean up my bookmark folders by getting rid of duplicated/links. i have created a program which will import 2 text files which contains a URL like this File 1: http://www.google/com http://anime.stackexchange.com/ https://www.fanfiction.net/guidelines/ https://www.fanfiction.net/anime/Magical-Girl-Lyrical-Nanoha/?&srt=1&g1=2&lan=1&r=103&s=2 File 2: http://scifi.stackexchange.com/ http://scifi.stackexchange.com/questions/56142/why-didnt-dumbledore-just-hunt-voldemort-down http://anime.stackexchange.com/ http://scifi.stackexchange.com/questions/5650/how-can-the-doctor-be-poisoned the program compares the 2 lists and creates a single master list with duplicate URLs removed. Now i have a few Backup bookmark folders in Firefox which on occasion i'll bookmark all tabs into a new folder with the date of the backup before i close off tabs or do reset my PC. each folder can have between 1000-2000 bookmarks, sometimes there are a bunch of pages which keep getting bookmarked, ie, i have ~50 pages on the Magical Girl Lyrical Nanoha Wiki on different spells, character and terminology which i commonly look back on. I'd like to know how i can export a bookmark folder so i have a list of URLs similar to what i use in my program

    Read the article

  • Memory modules not running at rated speeds.

    - by Wesley
    Hi all, I'm having some odd memory issues with my build. Here are my specs right now: QDI Superb 4 motherboard Intel Pentium 4 Northwood 2.4GHz (512KB L2, 533MHz FSB) 3x 256MB PC2100 DDR266 RAM 16MB NVIDIA TNT2 Pro AGP Seagate 80GB IDE HDD Generic USB 2.0 PCI Generic Modem PCI Bestec 250W PSU To be even more specific, here are the current brands and models of each module: Kingston KVR266X64C25/256 Samsung PC2100U-25331-Z SMART SM5643285D4N0CHM0H Supposedly, they are all PC2100 266MHz modules with a latency of 2.5. Looking in Speccy, the Kingston module is somehow running at a speed of PC2300 ~284MHz. I've never overclocked RAM at all as I don't know how to. However, when I first started the computer, I had the SMART module in place first and then reset the BIOS settings, including the integrated overclocking options. However, this still doesn't explain why the Kingston module runs at a higher speed than the SMART and Samsung module. Why is it like this? On a side note, where could I find the motherboard manual for the QDI Superb 4? Thanks in advance.

    Read the article

  • How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

    - by McCoy
    Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

    Read the article

  • Exchange 2010 CAS Removal == Broken???

    - by Doug
    Hi there, I recently upgraded to exchange 2010 and have a setup with 2 of my servers running CAS roles - EXCH01, EXCH02 EXCH02 just happens to also have a mailbox role where a lot of the users sit EXCH01 is my front facing CAS server, and is facing the net with SSL etc and incoming mail moving through it as a hub transport layer server as well. As i was trying to lean things out in my VM environment i removed the CAS role from EXCH02 and all hell broke loose. All the mail users that have a mailbox on EXCH02 had their homeMTA set to a deleted items folder in AD and so did their msExchHomeServer properties. After a complete battle i manually fixed these issues to the oldvalues, and in the mean time reinstalled CAS on EXCH02 (management was going nuts with out OUTLOOK working so i just put things back the way they were in a hurry.) I must add as a strange thing on the side, that before i reset these to point at EXCH02 i tried EXCH01 and it failed. I still want to remove the CAS role from EXCH02 as it should really not have it (error on install/planning on my part) and would have thought that this would not cause the issues it did, i assumed that the fact that there was another CAS server in the admin group all would be good. Was i wrong in my assumption? and what can i do to complete this successfully the second time round? Do i need to rehome all the mailboxes to the CAS server? is this a bug in the role uninstall?

    Read the article

  • Router not connecting to the internet

    - by Peter
    I had a weird problem this morning with my router - it's an Alice Gate VoIP 2 Plus WI-FI - not connecting to the internet after more or less 1 hour online (I'm always connected with the ethernet cable). The led status lights for Power, WI-FI, ADSL, Internet, Service should be on in order to be connected and navigate online. The problem was that the leds ADSL, Internet were off and I did not know why because it never happened before. I looked at the stats in the settings and the numbers for Bytes/Packages for both Sent/Received were there and increasing but I couldn't connect to the internet. I called tech support, they checked and told me to keep the router on for 48 hours because they were checking it. I've reset it twice before and after I called tech support and it still did not work so after about 2 hours of waiting I tried connecting using WI-FI and the leds 'magically' turned on, first the ADSL and Internet(Internet led always turns on last). At this point I'm curious what could of caused this and I'm doubting that the tech-support guys did something. What could of been the problem with the ethernet cable not connecting in the first place? It always works. What do the tech support guys normally do when they tell me to keep the router on so they can 'check it'? PS: I'm using ubuntu 32 bit

    Read the article

  • Windows 7 BSOD on startup

    - by Cristy
    I got a BSOD today after getting home from 11 hours of work... It seems to work in SAFE MODE (sometimes, not always) The BSOD says: SYSTEM_SERVICE_EXCEPTION STOP: 0x0000003b WimFsf.sys - Address FFFFF88001A6B76B base at FFFFF88001A600000, DateStamp 4a5bc362. Sometimes it shows the welcome screen, shows the destkop for a few seconds and then BSODs Already did: unplugged all the USB devices reset the CMOS I haven't installed any new software recently. What should I do? EDIT: I've managed to get into safe mode and it seems to works fine. When I go into normal mode it shows the desktop then it freezes... Is it more likely to be a software or hardware problem? EDIT2: I've managed to get into normal mode by disabling all the non-microsoft services & startup programs. One more thing: When I shut down my PC, on the "Logging off" screen appear some artifacts. I don't think it's because of my graphics card cause I've opened Black OPS and it worked fine. It's so strange... It still BSODS on startup (but there a ~=10% that it will not), and when it doesn't BSOD's it works fine...

    Read the article

  • Mac, VNC and multiple monitors

    - by MarqueIV
    I asked a similar question here before but apparently I wasn't as clear as I had expected by the responses. That said, I'll try again. I have a Mac Pro with quad monitors which I would like to access remotely. I've been using VNC for this (either via screen sharing or a dedicated VNC client), which works, but the VNC protocol matches the physical layout/resolutions of attached monitors. One of the things I like about Microsoft's Remote Desktop (Terminal Server) client is that when you connect, it blanks out the local screens and sets the resolution to a client-specified setting. In other words, when natively running Windows, even though I'm running a physical 30" monitor flanked by 2 24" monitors as well as a 21" Cintiq monitor, I can set the Remote Desktop resolution to match my notebook's screen giving me a native, single-monitor configuration. As soon as I disconnect (and you log back in locally), the desktop un-blanks and the resolution resets back to the four physically attached monitors. Again, VNC works and yes I know I can use 5901, 5902...n to attach VNC to a specific monitor as opposed to the entire desktop, but I'm still at the mercy of trying to look at a 2560x1600 resolution on a 1280x800 screen. I'm left with either scaling (everything's too small) or panning/scrolling (it's like playing hide-and-seek with your documents!) SO... anyone know of any Mac-based remote software (client and server) that will let me connect to my Mac Pro and reset the resolution by the client, just like you can in Windows, or am I SOL?

    Read the article

  • Apache Server not working in MAMP

    - by jasonaburton
    Here's what I did before the problem started: I was creating a database for a site that I am working on in phpMyAdmin. I wrote some code to try to connect to the database I just created and I couldn't connect. I assumed it might be because I needed a password to connect to the database, so I created a password for it. Immediately after I created the password phpMyAdmin kicked me out saying: "#1045 - Access denied for user 'root'@'localhost' (using password: YES)" "phpMyAdmin tried to connect to the MySQL server, and the server rejected the connection. You should check the host, username and password in your configuration and make sure that they correspond to the information given by the administrator of the MySQL server." I found the php.ini file and searched for where I could change the password to match the one I just made, but couldn't find where I needed to change it. So I decided to scrap the database and uninstall MAMP from my computer and reinstall it hoping it would just reset all the defaults and I could go on my merry way. But now after reinstalling MAMP and trying to run the servers Apache won't start up and I have no idea why. One problem after another... Any advice or helpful ideas?

    Read the article

  • Client unable to access OWA website after temporarily changing SSL certificate on the server

    - by Lorenz Meyer
    I have the following issue: One client computer (Windows XP) cannot access the OWA website. All other client computers can (Except another one in the same remote office). How this happened: I temporarily changed the SSL certificate on the Exchange Server yesterday. After a few minutes, I reverted back, an now the same certificate that was installed for years is back again. During these few minutes, they were in OWA on this computer and got a certificate error. What exactly happens: Internet Explorer displays the error Internet Explorer cannot display the webpage, Firefox displays The connection was reset and Crome shows This webpage is not available. The connection to ... was interrupted. What I already did to try to get this working: Restart the client computer Restart the exchange server Deleted Internet Explorer browsing history In IE, Internet Options, tab Content, under Certificates deletes SSL cache Restored Internet Explorer to the default parameters I looked into certmgr.msc, but did not find a certificate related to the issue What could I do else to narrow down the origin of this problem (or better: resolve it) ? Can you give any advice ?

    Read the article

  • Configuring network route between two routers on home network

    - by Paul
    I have a home network - the main router connected to the internet (and has wifi) is a Netopia box. Connected to it is a Linksys router. Everything currently works - I can connect via the wireless network and get to the internet. Machines connected to the Linksys can connect with each other and connect to the internet. Both routers are configured to serve addresses via DHCP (Netopia 192.168.1.1 - 192.168.1.99), Linksys (192.168.0.1 - 192.168.0.100). Here's how they are connected: Internet <-> Netopia w/wifi (192.168.1.254) <-> Linksys (192.168.0.1) I decided I really need to allow wireless connections to also communicate with machines behind the Linksys router. Currently the Linksys is configured to obtain an IP address via DHCP. I thought this would be straightforward. I configured the Linksys to have a static IP address: IP: 192.168.1.100 Mask: 255.255.255.0 GW: 192.168.1.254 Then I configured a static route on the Netopia: Network: 192.168.0.0 Mask: 255.255.255.0 GW: 192.168.1.100 So it should now look like this: Internet <-> Netopia w/wifi (192.168.1.254) <-> (192.168.1.100) Linksys (192.168.0.1) I reset both routers. I cannot ping the Netopia (192.168.1.254) from inside the Linksys network, and if I attempt to ping 192.168.0.1 from a wifi connection I get a "Destination host not available" error. Obviously I'm missing something, but I'm not sure where. Any ideas on what I'm missing?

    Read the article

  • How do I diagnose the cause of a freeze after resuming in Windows XP (SP3)?

    - by Software Monkey
    I have just built a new computer from parts. Whenever I resume from any sleep mode (S1, S3 or S4) the computer freezes within about 60 seconds of the welcome screen appearing. I have updated the BIOS and all drivers to current from the motherboard manufacturer's site. I have reset BIOS settings to default, including disabling AMD Cool n Quiet. The windows event logs are not helpful at all. Other than immediately after resuming the system is stable as long as AMD CnQ is disabled. The system is: Mobo : MSI 790GX-G65 CPU : AMD Phenom II 965 BE at 3.6 GHz Memory : Corsair DDR3 1600, at 1333 MHz and 9-9-9-21 HDDs : 1 EIDE, 2 SATA in RAID-0 DVD : 1 Card Reader: 1 multi-card reader Keyboard is attached via PS2 and mouse is USB. Any thoughts or pointers would be most welcome. EDIT: It appears that the computer may not freeze if a program is left running which puts it under significant load. I left a stress test running which keeps all cores under 85% load, and my son put the computer to sleep - while this program is running it I have been able to resume from S3 successfully 4 times, compared against about 20 tests with the computer idle which have all frozen. So this may be related to being in an idle state when it resumes.

    Read the article

  • Setting up port forwarding for web server

    - by Javier Badia
    This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

    Read the article

  • AGP 4x slot running at 2x

    - by Wesley
    Hi all, Here are the specs of the machine related to this question: AMD Athlon XP 2400+ @ 2 GHz / 2x 512MB PC3200 DDR RAM / 3D Fuzion 128MB GeForce 6200 AGP / WD 160GB IDE HDD / FIC AM37 (mobo) / Codegen 350W PSU / Windows XP Pro SP3 So, for some odd reason, the GeForce 6200 that is in the AGP 4x slot is not running at 4x, but 2x. The card itself supports AGP 4x and even 8x. When I enter the BIOS, the options for the AGP slot only allow 2x as the max. Before, the max option for the AGP slot in the BIOS was 4x. (I do get the 4x option after I reset CMOS, but it does not stick after a restart.) I don't exactly know what the problem could be, but a few weeks ago, this machine's hard drive was reformatted and got a fresh install of XP. Also, I did install Rivatuner, but I never overclocked it at all. (I uninstalled it after thinking that it had done something.) Otherwise, I cannot figure out the cause of the problem. Does anybody have an idea why this is happening? (Would I have to do another reformat?) Thanks in advance. PS: the other options for the AGP slot are aperture size (which I tried changing, but it did nothing) and FastWrite (enabled by default).

    Read the article

  • Ubuntu networking issue: two specific machines cannot browse web while connected to network at the same time.

    - by jensendarren
    I have setup a secure wireless network which works very well except for two laptops running Ubuntu 10.10 that can't access the Internet via a browser at the same time. They can both ping sites, wget sites, use skype but when using a browser the page never loads (in Firefox the status bar just sits there saying "Connecting" until it times out.) Here is what we have tried so far (nothing has fixed this issue): OpenDNS Restart networking services Using wired connection rather than wireless Removing all other nodes from the network except the two machines that have this issue Swapped out the router Factory reset the router Reformatted one of the machines and re-installed Ubuntu 10.10 Other things that we have checked: The two machines can connect simultaneously without any issues to other wireless networks in different locations (say in an Internet Cafe or another office) The two machines have unique IP addresses The two machines have unique MAC addresses The two machines can communicate on the network using Skype, wget, ping etc We are not using a proxy on either machine FYI: I have attached output from wireshark. For the test we turned both machines on and pointed them both to the same website. The content loaded on one and not the other. Here is the output from wireshark- (speedyshare.com/files/26228631/machine_output_1 && speedyshare.com/files/26228649/machine2). As you can see the first one worked, the second one didn't. I don't fully understand the output and would appreciate if someone could shed some light on what might be causing this and how we can fix it! Many thanks! Darren

    Read the article

  • Compaq Motherboard gives "CPU Fan Error"

    - by John
    I have a motherboard for a HP business desktop dx5150 PC. The model written on the board is "MS-7050" and it is for an AMD socket 939 processor. I got everything installed in it, and when I turned it on, it showed a message stating that there was a "CPU Fan Error" (or some similar language) and then turned off. It never stays on for more than about 30 seconds, probably less. The fan had previously been working great, but I replaced it anyway with a brand new Cooler Master fan. This did not work. I then reset the BIOS with the jumpers on the board, no dice. I replaced the CMOS battery. Same error. I then replaced the entire computer power supply with a brand new Antec, same error. The fan header is keyed, and has room for 3 pins. The CPU fan is designed the same way, so its not that I'm missing a temperature sensor or anything. Can anyone give some suggestions? Especially maybe some secret keystrokes to bypass this error?

    Read the article

  • Wake-on-lan only works so many times

    - by Chance
    I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

    Read the article

  • Prevent Outlook 2010 Insert Picture resizing image

    - by Rup
    When I "Insert Picture" a JPEG in Outlook 2010 it automatically resizes the image and, I think, recompresses it too. I realise this would be useful for photographs or for people who try to email 1MB BMPs but I would like to email around an image at the original pixel size without recompression. Is there a way to turn this off, or better still choose settings for each image insert? I found this page in the Office help. It's for Word, PowerPoint and Excel not Outlook but points you at File, Options, Advanced, Image Settings. There's no equivalent section in Outlook. I know Outlook uses Word as its editor so I've looked at Word's settings but there isn't an 'original size' here: there's only 'turn off image recompression' and pick target DPI from 96, 150, 220. I guess Office is finding a DPI value in the JPEG file and scaling it up or down to match this setting. I can't find an equivalent option in Outlook's options menu but there's so many settings and pop-up dialogs I may have missed something. Picture Format, Reset image size resets the image to the rescaled version, not the original. I can't see a way to edit a pixel value into size values in the image properties after insert. Thanks! I realise I can probably achieve this by editing the image metadata in PhotoShop elements or similar but there ought to be a way without editing the file? This is new behaviour in Outlook 2010; 2007 didn't do this.

    Read the article

  • Slow browsing through IE on Windows Server 2012

    - by Volodymyr
    We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

    Read the article

< Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >