Search Results

Search found 13347 results on 534 pages for 'embedded device'.

Page 468/534 | < Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >

  • Linux wireless disconnect every 20 minutes

    - by james
    My laptop uses CentOS 6.3 with kernel 2.6.32-279.el6.x86_64. My wireless adaptor is Intel Corporation Centrino Wireless-N 1000. My wireless connection always get off after about 20 minutes. The network applet shows the connection is still on with good signal strength, but I just cannot load any web pages even the configuration page of the wireless router. The problem will continue until I disable and reconnect the wireless. Other devices like my cell phone uses the same wireless network without the problem. Even yesterday I'm using the same laptop with Fedora 17 without this problem. I also searched the internet and someone said running services NetworkManager and network simultaneously may be a problem. But I cannot stop any one of them because: if I stop network and start NetworkManager, the network service will start automatically; if I stop NetworkManager and run network, it says "Device does not seem to be present, delaying initialization." when trying to bringing on the wireless. What shall I do to get rid of the problem? Thank you very much!

    Read the article

  • IP6 seems to be enabled - How do I configure it without interfering with IP4?

    - by Mister IT Guru
    I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

    Read the article

  • Connecting a laptop to a TV via HDMI

    - by Madmartigan
    I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

    Read the article

  • Can any iSCSI NAS appliance replicate / clone a LUN to an external drive?

    - by Boden
    I would like to backup using Windows Imaging to some kind of NAS appliance. I believe this will require the NAS to support iSCSI. I would then like the appliance to support the replication of the iSCSI LUN to an external eSATA or USB disk connected directly to the appliance. I've found plenty of NAS appliances that can do iSCSI and replicate to an external drive, but none that I've found thus far can do both at once. That is, the devices can do iSCSI, but then the replication feature doesn't work. The idea here is to backup to an appliance located in a secure office far away from the server room. Offsite backups to external hard drive could be managed from the appliance. The benefits of such a setup would be: 1) very unlikely that fire or random theft would affect both server-room backup and "remote" backup appliance 2) offsite backups could be managed by multiple trusted people without granting access to server room 3) Windows imaging provides poor man's deduplication, so each backup volume can contain a decent backup history. I understand why this would be a non-trivial thing to implement, but I'm wondering if such a thing exists? Preferably a tabletop, low to medium cost device. Alternative solutions welcome. NOTE: I'm backing up very few but very large files, so file replication is not a good option.

    Read the article

  • A router that supports connecting with 2 different wifi networks

    - by Allan Deamon
    I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

    Read the article

  • "A disk read error occurred" after choosing to boot into Windows XP from GRUB

    - by kellogs
    "A disk read error occurred" appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris Here, sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I cannot recall how exactly have I used testdisk but it once said: Disk /dev/sda - 160 GB / 149 GiB - CHS 19458 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 169 GB / 157 GiB) Check the harddisk size: HD jumper settings, BIOS detection... So far I have tried to "fixboot" and "chkdsk" from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please? Thank you!

    Read the article

  • On linux, what does it mean when a directory has size 0 instead of 4096?

    - by kdt
    Here's a strange thing I haven't seen before -- a directory whose size is reported by ls as 0 instead of 4096, and I can't create any files within it. # ls -ld lib home drwxr-xr-x. 2 root root 0 Feb 7 03:10 home <-- it has zero size dr-xr-xr-x. 11 root root 4096 Feb 4 09:28 lib # touch home/foo touch: cannot touch `home/foo': No such file or directory <-- and I can't create files in it # rm home rm: cannot remove `home': Is a directory <-- look, it really is a dir So what does it mean for a directory to have size 0 instead of 4096? Filesystem is ext4 on fedora core 14. The output of mount is: /dev/mapper/vg_dev-lv_root on / type ext4 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw,rootcontext="system_u:object_r:tmpfs_t:s0") /dev/vda1 on /boot type ext4 (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) Output of du -s /home: 0 /home Output of stat /home: File: `/home' Size: 0 Blocks: 0 IO Block: 1024 directory Device: 15h/21d Inode: 34913 Links: 2 Access: (0755/drwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2011-02-07 03:45:46.188995765 -0800 Modify: 2011-02-07 03:11:59.980995019 -0800 Change: 2011-02-06 07:58:45.874995002 -0800

    Read the article

  • Windows 7 sharing folder from command line, selecting users and triggering the "Apply" of changes

    - by clintp
    I have a drive that doesn't get mounted until after I log in. (A Truecrypt thumbdrive device, and no, I'm not making it a "System Favorite" to get around this.) I'd like to construct a batch file to share it once I've gotten it mounted because the sharing info doesn't seem to stick through a reboot. From the GUI, I'd go into the folder Properties-Sharing. And then in Advanced Sharing I'd pick the name to share it as. And then under the "Share..." button I'd pick the users and the permissions I want to grant them. After "Apply" there's a pause -- I'm not sure what's happening here, but the dialog says "Sharing Items..." -- and then everything is okay. From the command line, I've done: net share MyFolder=F:\MyFolder cacls F:\MyFolder /G FirstUser:F cacls F:\MyFolder /G OtherUser:F And this almost works. I can see the share on the network then, but nobody has permissions to do anything. If I go into the GUI and change anything (and I can see my command-line changes in there already) and press "Apply" I get the: "Sharing Items.... This may take a few minutes" Dialog... and then Voila! It works. I get the "Your folder is shared" dialog with the command-line changes I made, along with the GUI change that I made to trigger the "Sharing Items..." dialog. Everything's peachy. Is a service being restarted? Which one? What's triggering the sharing to take effect? And -- more importantly -- how do I do it from the command line?

    Read the article

  • Window 7 Host does not answer to ping

    - by gencha
    Today I tried printing on a shared printer on one of our homegroup members. Sadly it did not work (printer marked as offline). Shortly after, I noticed I can't even ping the machine that owns the printer (I also can not remotely access it in any other way I've tried). Currently I'm trying to ping the machine from the router both computers are connected to (and my machine in question doesn't answer). I do receive the echo requests (as verified with WireShark). I also added a rule in the Windows Firewall to specifically allow ICMP echo requests, but that didn't change anything. I also tried netsh firewall set icmpsetting 8 enable, but that didn't change anything either. Completely disabling the Windows Firewall has no effect on the issue either. One has to wonder, where does Windows log when and why it ignored any incoming packets? How can I get to the bottom of this? Here are some ways I found to dig deeper into the issue: Enabling logging on the Windows Firewall Enabling Windows Filtering Platform Auditing Both methods at least give more insight into the issue. The plain log file is full of entries like this: 2011-11-11 14:35:27 DROP ICMP 192.168.133.1 192.168.133.128 - - 84 - - - - 8 0 - RECEIVE So the ICMP packets are being dropped as if that was intended. The Event Viewer now gives a little bit more details: The Windows Filtering Platform has blocked a packet. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 192.168.133.1 Source Port: 0 Destination Address: 192.168.133.128 Destination Port: 8 Protocol: 1 Filter Information: Filter Run-Time ID: 214517 Layer Name: Receive/Accept Layer Run-Time ID: 44 This same entry is always repeated with 2 points of information changing: Process ID: 420 Application Name: \device\harddiskvolume2\windows\system32\svchost.exe The service host with the PID 420 is the host for the following services: Windows Audio DHCP Client Windows Event Log HomeGroup Provider TCP/IP NetBIOS Helper Security Center Additionally, there is currently this problem with the same machine: Even though my network is set to be a "Home network", I am unable to create a new homegroup.

    Read the article

  • ConfigMgr 2012 - How to automatically make updates available to computers without forcing them to be installed?

    - by Massimo
    I'm using System Center Configuration Manager 2012 with the Software Update Point feature; however, in this environment patching has to be strictly manual, because server reboots need to be approved and scheduled by different people; thus, I need to use ConfigMgr's SUP like I would use a plain WSUS server with auto-approval but with manual installation. I created some Automatic Deployment Rules to automatically download and deploy critical updates, and to have an installation dealine of "as soon as possible"; but then, I've also configured those rules to not do anything when the deadline is reached, and to not perform system restarts even if needed (see image). Also, I've configured the device collection to where those rules deploy updates to not have any valid maintencance window. However, I'm experiencing quite the opposite as what I was expecting: as soon as the new updates are processed by the ADRs, they get automatically installed on all systems by the Software Center, and the computers are subsequently restarted. Why is this happening? Am I getting something wrong or is just ConfigMgr 2012 not behaving like it should?

    Read the article

  • How to record tv to network share with Windows Media Center?

    - by Peterdk
    Well, you would think that Windows 7's new MediaCenter would be up to the task of recording your TV to a network share/drive. Too bad, it looks like it's just not possible. I have a windows 2008 R2 server, and a Windows 7 machine with a TV card. Since my server has 2TB of storage, it would be nice to record directly to it's networked drive. (I mounted it as Z:). I tried the following: Selecting it in Media Center Itself: Not working. Not available. Editing the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Service\Recording , setting RecordPath to Z:\TV. Not working. Editing the registry: setting RecordPath to \\server\TV. Not working. Creating a Symlink (mklink \D) to Z:\TV and \\server\TV and setting that in the registry as RecordPath. Currently I am out of options. I could ofcourse Install Windows7 on my server, but I have no license for that, and my windows 2008 r2 is free from dreamspark. Are there people that are succesfully recording to a networked drive/storage? edit I also need to mention that I need to be able to acces the stored files from other PC's, like my laptop. So iSCSI is great for recording, but it looks like you can't access iSCSI devices from multiple PC's. Looks like sharing a iSCSI device is out of the question, so: Are there workarounds to get this thing recording to my network drive?

    Read the article

  • Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

    - by gts123
    I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

    Read the article

  • Computer always freezing after random periods of time. No errors listed.

    - by Wesley
    Hi, all. Here are my specs beforehand: AMD Athlon XP 2400+ @ 2.00 GHz, 160GB IDE HDD, 128MB GeForce 6200 AGP, 2 x 512MB PC3200 DDR RAM, CoolMax 350W PSU, 1 x CD-RW Drive, 1 x DVD-ROM Drive, FIC AM37 Mobo, Windows XP Pro SP3 My desktop freezes after random periods of time but there are no errors listed in the Event Viewer after a forced shutdown and restart. A couple months ago, I found that when it froze, the floppy was being accessed at the same time. So, I disconnected the floppy (since I never used it anyways) from the power supply and motherboard. Everything was working fine and the computer never froze. This past Christmas break, I left for a Conference and when I got home, the computer kept freezing again. So, this time, I just disconnected the DVD reader (from mobo and power) and started it up. Still, it froze almost right away. Then I found some older sticks of RAM (2 x 256MB PC2100 DDR) and swapped them in. Everything worked fine again after that. I even swapped the 2 x 512MB PC3200 DDR RAM back in and everything worked okay. Then it started freezing again, and I tried all possible RAM combos, still freezing within 5-10 minutes of startup. One thing I've realized is that the floppy drive is still listed in My Computer and I uninstalled it from my Device Manager already. There were no software errors, and I uninstalled the most recent software, with no effect. Still, I have no idea what is wrong because everything ran fine before that. Any suggestions? EDIT: Still have yet to buy some blank CD media to use Memtest86+. However, would a lack of virtual memory cause the computer to freeze? EDIT2: So after a long time, I ran Memtest86+ and all is well. Turns out though, after removing my original DVD reader and replacing it with a DVD-ROM drive, there is no freezing whatsoever! Thanks for all your suggestions!

    Read the article

  • Juniper NetScreen NS-5GT traffic monitoring

    - by blah
    I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

    Read the article

  • WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

    - by Elton Carvalho
    I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

    Read the article

  • How to increase the speed between two external hard drives on my laptop?

    - by Roman
    Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

    Read the article

  • How to increase the speed between two external hard drives on my laptop?

    - by Roman
    Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

    Read the article

  • How do I determine how future-proof and stable a router is?

    - by Aarthi
    I mentioned in my last question that my wireless router had a bad habit of crashing. After consulting with the Super User chatroom, as well as my sysadmin, I've decided I may as well purchase a new router. However, I'm unsure how to evaluate all these tech specs that get touted about. The two things that seem to be the most important to me are: (1) keeping my router future-proof (as standards evolve and change), and (2) ensuring its stability. Unfortunately, I'm not sure what, exactly, I should be looking for in the tech specs or the item description that can give me a good idea of how stable or future-proof my decide will be. What should I look for? Can I determine stability without having to try the device out myself? Please note: I'm not a battle-hardened power user by any means, so I'll likely be reliant on the given firmware for my router. My last router lasted me like four years, so I mostly just want something that'll cover a 500 sqft apartment in New York with minimal crashing, so that I can watch Hulu in peace. And make Skype calls. If it helps, the router models that I'm currently decided between are this ASUS one and this LinkSys one.

    Read the article

  • How to configure traffic from a specific IP hardcoded to an IP to forward to another IP:PORT using i

    - by cclark
    Unfortunately we have a client who has hardcoded a device to point at a specific IP and port. We'd like to redirect traffic from their IP to our load balancer which will send the HTTP POSTs to a pool of servers able to handle that request. I would like existing traffic from all other IPs to be unaffected. I believe iptables is the best way to accomplish this and I think this command should work: /sbin/iptables -t nat -A PREROUTING -s $CUSTIP -j DNAT -p tcp --dport 8080 -d $CURR_SERVER_IP --to-destination $NEW_SERVER_IP:8080 Unfortunately it isn't working as expected. I'm not sure if I need to add another rule, potentially in the POSTROUTING chain? Below I've substituted the variables above with real IPs and tried to replicate the layout in my test environment in incremental steps. $CURR_SERVER_IP = 192.168.2.11 $NEW_SERVER_IP = 192.168.2.12 $CUST_IP = 192.168.0.50 Port forward on the same IP /sbin/iptables -t nat -A PREROUTING -p tcp -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.11:8080 Works exactly as expected. IP and port forward to a different machine /sbin/iptables -t nat -A PREROUTING -p tcp -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.12:8080 Connections seem to timeout. Restrict IP and port forward to only be applied to requests from a specific IP /sbin/iptables -t nat -A PREROUTING -p tcp -s 192.168.0.50 -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.12:8080 Times out as well. Probably for the same reason as the previous entry. Does anyone have any insights or suggestions? thanks,

    Read the article

  • Server Clustering (Django, Apache, Nginx, Postgres)

    - by system-matrix
    I have a project deployed with django, Apache, Nginx and Postgres. The project has requirement of live data viewable to customers. The projects main points are: 1. Devices in field send data to server(devices are also like website users) after login. 2. There is background import process which imports the uploaded data in postgres. 3. The webusers of the system use this data and can send commands to the devices, which devices read when they login. 4. There are also background analysis routines running on the data. All the above mentioned setup and system is deployed on one amazon EC2 cloud machine. The project currently supports over 600 devices and 400 users. But as the number of devices are increasing with time the performance of the server is going down. We want to extend this project so that it can support more and more devices. My initial thinking is, We will create one more server like current one and divide the devices amongst these to servers. But Again We need a central user and device managment point though django admin. Any Ideas? What are the best possible ways to create a scalable architecture? How can I create a Postgres Cluster and Use it with Django, if possible?

    Read the article

  • Ubuntu 13.10 - How to disable LVM and cryptsetup? cryptsetup: evms_activate is not available

    - by NeverEndingQueue
    I am trying to remove whole drive encryption from my Ubuntu installation. I've run Ubuntu from Live CD, mounted crypt partition and copied it to another partition /dev/sda3. sudo cryptsetup luksOpen /dev/sda5 crypt1 sudo dd if=/dev/ubuntu-vg/root of=/dev/sda3 bs=1M After that I've run boot-repair: https://help.ubuntu.com/community/Boot-Repair Added entry to /etc/fstab: UUID=<uuid> / ext4 errors=remount-ro 0 1 Of course I've replaced with blkid result of my /dev/sda3. I've also deleted overlayfs and tmpfs lines from /etc/fstab. (I've just compared it to content of /etc/fstab in non-encrypted Ubuntu installation and could not find overlayfs and tmpfs). I've chrooted from LiveCD into my system and rebuilt initramfs: http://blog.leenix.co.uk/2012/07/evmsactivate-is-not-available-on-boot.html I've also removed cryptsetup using apt-get remove. Basically I can easily mount my system partition from Live CD (without setting up the encryption and LVM stuff), but can not boot from it. Instead I see: cryptsetup: evms_activate is not available When I've chosen the Recovery mode I've seen this: Begin: Mounting root file system ... Begin: Running /script/local-top ... Reading all physical volumes. This may take a while ... No volume groups found cryptsetup: evms_activate is not available Begin: Waiting for encrytpted source device ... My /etc/crypttab is empty. I am pretty sure that system tries to find encrypted partition, search for LVMs etc. Do you have ideas what could be the problem or how can I fix it? Thanks

    Read the article

  • Software RAID 1 Configuration

    - by Corve
    I have created a software RAID 1 quite some while ago and it always seemed to work for me. However I am not completely sure that I have configured everything right and do not have the experience to check so I would be very grateful for some advice or just verification that all seems right so far. I am using Linux Fedora 20 (32 bit with plans to upgrade to 64bit) The RAID 1 should consist of two 1TB SATA hard drives. This is the output of mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sun Jan 29 11:25:18 2012 Raid Level : raid1 Array Size : 976761424 (931.51 GiB 1000.20 GB) Used Dev Size : 976761424 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Sat Jun 7 10:38:09 2014 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : argo:0 (local to host argo) UUID : 1596d0a1:5806e590:c56d0b27:765e3220 Events : 996387 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 0 1 active sync /dev/sda The RAID is mounted successfully: friedrich@argo:~ ? sudo mount -l | grep md0 /dev/md0 on /mnt/raid type ext4 (rw,relatime,data=ordered) Basically my question are: Why do I only have 1 active device? What does the State removed at bottom mean? Also I noticed some strange error messages that I see on the console on system start and shutdown and always repeating in the background when I switch with Ctrl + Alt + F2: ... ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: COMRESET failed (errno=-32) ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ... Are these errors related to the RAID? Something seems wrong with the SATA devices.. All together the system works (I can read and write to the mounted raid) but I always had these strange errors on startup shutdown (probably always in the background). Thx for your help

    Read the article

  • How do I copy files between harddrives on Ubuntu CLI?

    - by ed209
    I have a dedicated server with a 120gb main ssd. The server happens to come with a couple of 3000GB hard drives. I'd like to use them to back up my main drive. Preferably, I'd like one as an exact copy of the main SSD and the other with incremental backups of the mysql database and a user uploads file. These are the drives I have Disk /dev/sda: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f2e18 Device Boot Start End Blocks Id System /dev/sda1 2048 4196352 2097152+ 83 Linux /dev/sda2 4198400 5246976 524288+ 83 Linux /dev/sda3 5249024 234441647 114596312 83 Linux Disk /dev/sdb: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sdb doesn't contain a valid partition table Disk /dev/sdc: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table The first problem I have, is that I have no idea how to copy from one drive to another. Kind of embarrassing I know, but I don't know where to start. I'm thinking of this in terms of Mac OS cli where I'm able to copy between /Volumes - is there an equivalent? (there is nothing under /mnt or /media)

    Read the article

  • Possible Solution for Setting up a Linux VPN Server to Encrypt WLAN Traffic of Macs and iPhones on

    - by GorillaPatch
    I would like to set up a VPN server on debian linux to encrypt wireless traffic coming from my Mac or iOS device. I would like to use a certificate-based solution. Setting up a PKI infrastructure and managing certificates is OK for me. 1. Which server to pick? By looking through the internet and here on stackoverflow I found the following possible solutions: strongSwan IPSec and racoon Which solution is feasible for a linode running debian squeeze? 2. How to configure the network? If I understood correctly a VPN has a virtual network interface as an endpoint on the server side. Naively I would think that I need a DHCP server running on the server to assign a dynamic private IP (like of the class C network 192.168.xxx.xxx) to the connecting clients. Next I think I would need to set up masquerading to NAT the incoming VPN traffic to the real interface directly connected to the internet. Is this the right way to go? Do you have any configuration examples? I often saw VPN configurations used to connect to your home network, but that is not what I am looking for. I have a server up in the internet and want to use it as a proxy to encrypt traffic in insecure network environments like public WLANs.

    Read the article

  • Why isn't my phone charging with some micro usb cables?

    - by Jacxel
    I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

    Read the article

< Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >