Search Results

Search found 13347 results on 534 pages for 'embedded device'.

Page 470/534 | < Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• "Access is Denied" when executing application from Command Prompt

  - by xpda

  Today when I tried to run an old DOS utility from the XP Command prompt, I got the message "Access is Denied." Then I found that most of the DOS utilities would not run, even though I have "full control" over them. They worked just fine a few weeks ago, and I have not made any OS changes other than Windows Upgrades. Then I tried running edlin.exe and edit.com from the Windows\system32 folder. Same result - "Access is Denied." I tried running these applications from Windows Explorer and got the message "Windows cannot access the specified device, path, or file. You may not have the appropriate permissions to access the item." I am logged in as a member of Administrators and have full control over these files. I tried logging in as THE Administrator, with no change. I checked the security settings on the files, and have full control over all of them. I have tried copying the files to different drives, booting in safe mode, and running without antivirus and firewall, all with no change. Does anybody know what could cause this?

  Read the article

• Fixing a corrupted Windows Server 2003 server

  - by Keith

  I have a Windows Server 2003 server that is being mainly used for some reporting done in SQL Server. Recently Windows has started complaining about being corrupted, we are getting an NTFS error 55: The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume1. The server is RAID 5 and I did have a disk die however the RAID never went degraded since I have a hotspare. I replaced the hot spare and I'm still having problems. When I run chkdsk I get tons of messages.. some are: Deleting corrupted attribute record (128, "") from file record segment 194746 Those go on for a while. Then it deletes some orphan files. Then it does Correcting error in index $I30 for file 132426 And that goes on for a while. Then I get tons of Recovering orphaned file RE1AB6~1.LOG into directory file 534959 I have seen a lot of errors relating to the SQL Server reporting services. What are my options at this point? I would prefer to fix the issue instead of building a new server but I don't know if I can at this point.

  Read the article

• fglrx-legacy-driver not seeing Radeon HD 4650 AGP

  - by Rocket Hazmat

  I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

  Read the article

• Replace Linux Boot-Drive | ext3 to btrfs

  - by bardiir

  I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

  Read the article

• Possible Solution for Setting up a Linux VPN Server to Encrypt WLAN Traffic of Macs and iPhones on

  - by GorillaPatch

  I would like to set up a VPN server on debian linux to encrypt wireless traffic coming from my Mac or iOS device. I would like to use a certificate-based solution. Setting up a PKI infrastructure and managing certificates is OK for me. 1. Which server to pick? By looking through the internet and here on stackoverflow I found the following possible solutions: strongSwan IPSec and racoon Which solution is feasible for a linode running debian squeeze? 2. How to configure the network? If I understood correctly a VPN has a virtual network interface as an endpoint on the server side. Naively I would think that I need a DHCP server running on the server to assign a dynamic private IP (like of the class C network 192.168.xxx.xxx) to the connecting clients. Next I think I would need to set up masquerading to NAT the incoming VPN traffic to the real interface directly connected to the internet. Is this the right way to go? Do you have any configuration examples? I often saw VPN configurations used to connect to your home network, but that is not what I am looking for. I have a server up in the internet and want to use it as a proxy to encrypt traffic in insecure network environments like public WLANs.

  Read the article

• Cisco access-list confusion

  - by LonelyLonelyNetworkN00b

  I'm having troubles implementing access-lists on my asa 5510 (8.2) in a way that makes sense for me. I have one access-list for every interface i have on the device. The access-lists are added to the interface via the access-group command. let's say I have these access-lists access-group WAN_access_in in interface WAN access-group INTERNAL_access_in in interface INTERNAL access-group Production_access_in in interface PRODUCTION WAN has security level 0, Internal Security level 100, Production has security level 50. What i want to do is have an easy way to poke holes from Production to Internal. This seams to be pretty easy, but then the whole notion of security levels doesn't seam to matter any more. I then can't exit out the WAN interface. I would need to add an ANY ANY access-list, which in turn opens access completely for the INTERNAL net. I could solve this by issuing explicit DENY ACEs for my internal net, but that sounds like quite the hassle. How is this done in practice? In iptables i would use a logic of something like this. If source equals production-subnet and outgoing interface equals WAN. ACCEPT.

  Read the article

• Software RAID 1 Configuration

  - by Corve

  I have created a software RAID 1 quite some while ago and it always seemed to work for me. However I am not completely sure that I have configured everything right and do not have the experience to check so I would be very grateful for some advice or just verification that all seems right so far. I am using Linux Fedora 20 (32 bit with plans to upgrade to 64bit) The RAID 1 should consist of two 1TB SATA hard drives. This is the output of mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sun Jan 29 11:25:18 2012 Raid Level : raid1 Array Size : 976761424 (931.51 GiB 1000.20 GB) Used Dev Size : 976761424 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Sat Jun 7 10:38:09 2014 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : argo:0 (local to host argo) UUID : 1596d0a1:5806e590:c56d0b27:765e3220 Events : 996387 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 0 1 active sync /dev/sda The RAID is mounted successfully: friedrich@argo:~ ? sudo mount -l | grep md0 /dev/md0 on /mnt/raid type ext4 (rw,relatime,data=ordered) Basically my question are: Why do I only have 1 active device? What does the State removed at bottom mean? Also I noticed some strange error messages that I see on the console on system start and shutdown and always repeating in the background when I switch with Ctrl + Alt + F2: ... ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: COMRESET failed (errno=-32) ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ... Are these errors related to the RAID? Something seems wrong with the SATA devices.. All together the system works (I can read and write to the mounted raid) but I always had these strange errors on startup shutdown (probably always in the background). Thx for your help

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• Display stretches 4:3 ratios; Adds scrolling to other ratios

  - by Matt

  I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks EDIT: After playing around more, I discovered that the "scrolling" behavior is only present for aspect ratios that are not 4:3. For 4:3 ratios, it just stretches out to fit the wide screen. My monitor's native ratio is 16:9 .. what could be causing it to think it needs to scroll?

  Read the article

• HP EliteBook 8440P - USB ports stop working on docking station

  - by r0ca

  I have a HP Elitebook 8440P running Windows XP Pro SP3. I installed it on my docking station and everything went smooth for a while. Last week, my mouse and any other USB devices stoped working sudenly... It was working fine on my laptop itself but nothing on my docking station. LCD attached monitor works and same for LAN and PS2 keyboard. I updated the BIOS, Chipset, Video Drivers, also changed my docking station by a brand new one but the problem still comes back. I also noticed something in Device Manager... A Generic USB Root Hub has an error on it, a Yellow/Orange exclamation mark. I tried to update that driver but no luck. Windows is unable to process it. This seems to be the problem but can't fix it. I may only re-image my laptop but for me, I need to avoid that since I have so many apps installed on it. If anybody has any advice, I'll take it!

  Read the article

• how can i move ext3 partition to the beginning of drive without losing data?

  - by Felipe Alvarez

  I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

  Read the article

• How to connect computers to a network printer behind a router?

  - by kokbira

  General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

  Read the article

• Network topology for both direct and routed traffic between two nodes

  - by IndigoFire

  Despite it's small size, this is the most difficult network design problem I've faced. There are three nodes in this network: PC running Windows XP with an internal WiFi adapter.Base station with both WiFi and a Wireless Modem (WiModem)Mobile device with both WiFi and WiModem The modem is a low-bandwidth but high-reliability connection. We'd like to use WiFi for high-bandwidth stuff like file transfers when the mobile is nearby, and the modem for control information. Here's the tricky part: we'd like the wifi traffic to go directly from the mobile to the PC, as rebroadcasting packets on the same WiFi channel takes up double the bandwidth. We can do that with a manual configuration by giving the both the PC and the base station two IP addresses for their WiFi interfaces: one on a subnet shared with the mobile, and one on their own subnet. The routes on the PC are set up so that any traffic going to the mobile via WiModem goes through the secondary IP address so that return traffic from the mobile also goes through the WiModem. Here's what that looks like: PC WiFi 1: 192.168.2.10/24 WiFi 2: 192.168.3.10/24 Default route: 192.168.2.1 Base Station WiFi 1: 192.168.2.1/24 WiFi 2: 192.168.3.1/24 WiModem: 192.168.4.1/24 Mobile WiFi: 192.168.3.20/24 WiModem: 192.168.4.20/24 We'd like to move to having the base station automatically configure the mobile and PC, as the manual setup is problematic when you start having multiple mobiles and PCs. This means that the PC can only have 1 IP address and needs to be treated as being pretty simple. Is it possible to have a setup driven by DHCP on the base station that is efficient with bandwidth?

  Read the article

• Hearing a clicking noise from soundcard all the time

  - by Mehrdad

  I have installed Fedora 17 on my laptop. A few days ago I updated my fedora (but not upgraded). I shut down my computer and since the next time I turned it on I am hearing a clicking noise all the time from speakers. Even when I plug my headphones in I hear the noise through the headphone. I surfed over the internet and found the following shell commands: su -c 'echo "options snd_hda_intel power_save=0" /etc/modprobe.d/snd_hda_intel.conf' su -c 'echo 0 /sys/module/snd_hda_intel/parameters/power_save' I tried them but they didn't work. Here is the part of "lspci" command related to my sound-card: 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) I have to add that my sound-card is working and I can play some audio file, I mean I can hear the voice and noise simultaneously. But everything is OK in windows xp which is also installed on my laptop. Could it be related to the sound-card driver? If so, how can I revert it to the previous version?

  Read the article

• Windows Server 2012 Can't Print

  - by Chris

  I know this may sound incredibly stupid and there is probably an easy solution but I can't seem to find it. Friends of mine recently upgraded their server for their small business from the POS old one. New hardware and a change from Windows Server 2003 to Windows Server 2012. I've got everything they need transfered over and running except for printing. They need to be able to print to printers in the vans their technicians use from the server via remote desktop. In other words the use a laptop to remote desktop into the server and need to print invoices out from the remote server to printers attached locally via usb. On the old server they just installed the identical driver and that was it, they could print as needed. On this server no matter what we seem to do we can't get it to print remotely, and in the process we also discovered that the server can't even print to the network printer. It sees the printer on it's network and it sees (through redirect) the printers in the vans but when you hit print it claims it did and nothing happens. There isn't an issue with the printers themselves as every other device we have can print to them without issues. Is there some setting that is inhibiting the server from printing? Is there something I need to install (print server?) to add the functionality? Thanks in advance for helping me out here

  Read the article

• Data recovery; nearly 1 tb of movies on a WD 3.5 tb personal cloud drive disappears with scanty traces

  - by Effector Dhanushanth

  I have a great collection of movies that I had stored in a logical mesh of folder on my 3.5 tb WD personal cloud drive. I woke up 1 morning and found that everything was fine with my data on this drive, except for my movie collection: There were two great folders, one "2sort" nd the other "segregated". out of all the segregated sub folders, only letter C D and 2 or 3 others remain. and the 2 sort folder, which has umpteen subfolders, amounting to more than 0.5 tb. is.. it's just gone!! this is a great downfall.. now this is a personal cloud drive and has no usb port etc. unfortunately to hardwire and recover files.. now I'm sure there are softwares out there that can help me recover my beloved movies from such an interestingly "hard-to-reach" (should I say?) device? what may that software be compadre, my happiness lies within your answer.. thank you.. remember, recovery software or (WD) personal cloud. :) these ovies were All, "hand-picked", over the course of ten years.. I just never catalogued my collection.. if I could just get the "list" of my lost collection, that'd be enough.. recovering em would be a bonus.. but they out to be damaged if I were to somehow recover you know? still, I'm certain they're all intact.. I guess the file index just got corrupted.. There surely is a veil of some sort that need to be thrown or pushed aside to reveal my movies.. what software can do/does that? thanks immensely!

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

• Data recovery from corrupt Ubuntu partition/directory (question about a previous answer)

  - by JoshMaurice

  I have an Ubuntu installation that won't boot anymore. I asked my previous question about it here: http://superuser.com/questions/15916/ubuntu-chkdsk-equivalent Bolotov replied: As I see from your previous question you can boot Windows so you could use dskprobe from Windows XP Service Pack 2 Support Tools to make sure that fs type is correct ... but it's already correct fs type 7 is NTFS. Message "The type of the filesystem is RAW. CHKDSK is not available for RAW drives." means that windows can't determine fs type for some reason. As we see fs type is correct. To run Chkdsk on your Windows partition you can install Windows Recovery Console, boot in recovery console and check your disk. After checking the disk you will gain access to you c:\ubuntu\disks. I think you can mount your linux partition (which is in file) as usual loop-back device: mount -o loop [path to your linux-loopback-partition] But you should mount windows patrition first. So now I'd like to know: Within the recovery console I will be issuing the commands "chkdsk -r" and then "mount -o loop [path to windows partition]" and then "mount -o loop c:\ubuntu\disks", correct? I do have a ("corrupt and unreadable") c:\ubuntu\disks directory so that appears to be the correct path to the linux partition; do you know the path to the windows partition? would that be just "c:\"?

  Read the article

• How to get http requests details in a tcpdump?

  - by tucson

  I am trying to get a tcpdump trace of some http requests. Here is what I got so far (I replaced the real IP addresses with REMOTE and LOCAL): C:\>Windump -na -i 3 ip host REMOTE and ip src LOCAL and tcp port 80 Windump: listening on \Device\NPF_{8056BE5E-BDBB-44E6-B492-9274B410AD66} 13:13:34.985460 IP LOCAL.4261 > REMOTE.80: . 1784894764:1784894765(1) ack 1268208398 win 65535 13:13:38.589175 IP LOCAL.4302 > REMOTE.80: F 3708464308:3708464308(0) ack 982485614 win 65535 13:13:38.589285 IP LOCAL.4303 > REMOTE.80: F 890175362:890175362(0) ack 2462862919 win 65535 13:13:38.589330 IP LOCAL.4304 > REMOTE.80: F 1838079178:1838079178(0) ack 156173959 win 65535 13:13:38.589374 IP LOCAL.4305 > REMOTE.80: F 3952718843:3952718843(0) ack 2209231545 win 65535 13:13:38.589413 IP LOCAL.4306 > REMOTE.80: F 446105750:446105750(0) ack 3141849979 win 65535 13:13:38.590265 IP LOCAL.4302 > REMOTE.80: . ack 2 win 65535 13:13:38.590403 IP LOCAL.4304 > REMOTE.80: . ack 2 win 65535 13:13:38.590429 IP LOCAL.4303 > REMOTE.80: . ack 2 win 65535 13:13:38.590484 IP LOCAL.4305 > REMOTE.80: . ack 2 win 65535 13:13:38.590514 IP LOCAL.4306 > REMOTE.80: . ack 2 win 65535 But I do not get the following level of details: Request URL:http://domain.com/index.php Request Method:POST Status Code:200 OK POST /index.php HTTP/1.1 Host: domain.com Connection: keep-alive Content-Length: 151 Cache-Control: max-age=0 etc How can I get this level of data?

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• Enable bitlocker an save key to share

  - by user273694

  I have searched all over the web but cannot find a complete answer to this: How to enable Bitlocker on a laptop with TPM, and store a file with the Bitlocker recovery key and TPM password by USING THE manage-bde command line tool. The file should be the same as when created in the Bitlocker manager UI. I DO NOT want to save to AD. The same question was asked here but was not answered correctly. The goal is to write a script to be used with an endpoint manager. I have tried the following: manage-bde -on C: Works fine, but does not create or save a key. manage-bde -on C: -rk C:\myfolder\ and manage-bde -on C: -RecoveryKey C:\myfolder\ -rp The output from the last two methods state that a key has been saved to c:\myfolder and so on, but that is not the case. It also says that I have to: Save the password in a secure location Insert a USB flash drive with an external key file into the computer. Restart and run hardware test type "manage-bde -status" to check if the hardware test succeeded After a restart, I get an error saying that Bitlocker could not be enabled because the bitlocker startup key or recovery kpassword cannot be found on the USB device.... C: was not encrypted. Why am I asked to insert a USB?? I simply want to encrypt the hard drive and save the recovery information to a file automatically. Is that too much to ask? Help please!

  Read the article

• Soundtest works, but no other sounds and windows starts very slowly

  - by Kristian Kari

  So suddenly all sounds on my computer stopped working expect the sound test works, but when I go to control panel and audio it says there's no audio device. And audio players and audio on website doesn't work either. and Also windows starts very slowly. I'm not sure if this helps but I'll tell what happened before this. I downloaded this program from a little shady website, I hesitated and for a good reason I guess cos the moment I finished downloading it, my antivir detected it as unwanted program and put it on quarantine. I thought everything was fine, but had some problems with program (won't go to details about it cos it's not really related to audio) so rebooted the computer and I was suprised that windows started really really slowly. It took like 5 mins to load the desktop such. After that I noticed the sounds were missing, I immediately deleted the program since I thought it was causing the problem. But it didn't change much. I tried to find the solution with no success and now I'm just scanning again my computer. I'd be thankful if anyone would be able to help me. I might have left a thing or ten things out, so feel free to ask. oh and I'm using windows xp

  Read the article

< Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >