Search Results

Search found 13347 results on 534 pages for 'embedded device'.

Page 472/534 | < Previous Page | 468 469 470 471 472 473 474 475 476 477 478 479  | Next Page >

• Recovering ZFS pool with errors on import.

  - by Sqeaky

  I have a machine that had some trouble with some bad RAM. After I diagnosed it and removed the offending stick of RAM, The ZFS pool in the machine was trying to access drives by using incorrect device names. I simply exported the pool and re-imported it to correct this. However I am now getting this error. The pool Storage no longer automatically mounts sqeaky@sqeaky-media-server:/$ sudo zpool status no pools available A regular import says its corrupt sqeaky@sqeaky-media-server:/$ sudo zpool import pool: Storage id: 13247750448079582452 state: UNAVAIL status: The pool is formatted using an older on-disk version. action: The pool cannot be imported due to damaged devices or data. config: Storage UNAVAIL insufficient replicas raidz1 UNAVAIL corrupted data 805066522130738790 ONLINE sdd3 ONLINE sda3 ONLINE sdc ONLINE A specific import says the vdev configuration is invalid sqeaky@sqeaky-media-server:/$ sudo zpool import Storage cannot import 'Storage': invalid vdev configuration I should have 4 devices in my ZFS pool: /dev/sda3 /dev/sdd3 /dev/sdc /dev/sdb I have no clue what 805066522130738790 is but I plan on investigating further. I am also trying to figure out how to use zdb to get more information about what the pool thinks is going on. For reference This was setup this way, because at the time this machine/pool was setup it needed certain Linux features and booting from ZFS wasn't yet supported in Linux. The partitions sda1 and sdd1 are in a raid 1 for the operating system and sdd2 and sda2 are in a raid1 for the swap. Any clue on how to recover this ZFS pool?

  Read the article

• Unable to resize ec2 ebs root volume

  - by nathanjosiah

  I have followed many of the tutorials that pretty much all say the same thing which is basically: Stop the instance Detach the volume Create a snapshot of the volume Create a bigger volume from the snapshot Attach the new volume to the instance Start the instance back up Run resize2fs /dev/xxx However, step 7 is where the problems start happening. In any case running resize2fs always tells me that it is already xxxxx blocks big and does nothing, even with -f passed. So I start to continue with tutorials which all basically say the same thing and that is: Delete all partitons Recreate them back to what they were except with the bigger sizes Reboot the instance and run resize2fs (I have tried these steps both from the live instance and by attaching the volume to another instance and running the commands there) The main problem is that the instance won't start back up again and the system error log provided in the AWS console doesn't provide any errors. (it does however stop at the grub bootloader which to me indicates that it doesn't like the partitions(yes, the boot flag was toggled on the partition with no affect)) The other thing that happens regardless of what changes I make to the partitions is that the instance that the volume is attached to says that the partition has an invalid magic number and the super-block is corrupt. However, if I make no changes and reattach the volume, the instance runs without a problem. Can anybody shed some light on what I could be doing wrong? Edit On my new volume of 20GB with the 6GB image,df -h says: Filesystem Size Used Avail Use% Mounted on /dev/xvde1 5.8G 877M 4.7G 16% / tmpfs 836M 0 836M 0% /dev/shm And fdisk -l /dev/xvde says: Disk /dev/xvde: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x7d833f39 Device Boot Start End Blocks Id System /dev/xvde1 1 766 6144000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvde2 766 784 146432 82 Linux swap / Solaris Partition 2 does not end on cylinder boundary. Also, sudo resize2fs /dev/xvde1 says: resize2fs 1.41.12 (17-May-2010) The filesystem is already 1536000 blocks long. Nothing to do!

  Read the article

• How does Google geo location service work?

  - by heaosax

  I dont use google maps much, but I was using it today and I clicked the "Show my location" button for the first time, then firefox asked for permission and I clicked "share my location", google maps showed my location pretty accurate. But, how does this system really works? I mean how can google know where I live? I am connecting to the internet with a VPN, so my "public IP" is not from my country, but from sweden, also I use linux and I change the mac of my wireless device, but google still show my location. I know I can disable this feature setting firefox about:config geo.enabled to false, but I am curious about how google can know where I live even when I dont have a real mac address and my IP is not from my real country. Basically I'd like to know if this feature works only because of code that exists in chrome and firefox (which spies my system)? I am worried about anyone knowing where I live, I mean... where is my privacy? Part of the fun about the internet is remaining anonymous.

  Read the article

• a disk read error occurred [closed]

  - by kellogs

  Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Redirecting or routing all traffic to OpenVPN on a Mac OS X client

  - by sdr56p

  I have configured an OpenVPN (2.2.1) server on an Ubuntu virtual machine in the Amazon elastic compute cloud. The server is up and running. I have installed OpenVPN (2.2.1) on a Mac OS X (10.8.2) client and I am using the openvpn2 binary to connect (in opposition to other clients like Tunnelblick or Viscosity). I can connect with the client and successfully ping or ssh the server through the tunnel. However, I can't redirect all internet traffic through the VPN even if I use the push "redirect-gateway def1 bypass-dhcp" option in the server.conf configurations. When I connect to the server with these configurations, I get a successful connection, but then an infinite series of error messages: "write UDPv4: No route to host (code=65)". Traffic routing seems to be compromised because I am not able to access anything anymore, not even the OpenVPN server (by pinging 10.8.0.1 for instance). This is beyond me. I am finding little help on the web and don't know what to try next. I don't think it is a problem of forwarding the traffic on the server since, first, I have also took care of that and, second, I can't even ping the VPN server locally through the tunnel (or ping anything at all for that matter). Thank you for your help. Here is the server.conf. file: port 1194 proto udp dev tun ca ca.crt cert ec2-server.crt key ec2-server.key # This file should be kept secret dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 And the client.conf file: client dev tun proto udp remote servername.com 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert Toto5.crt key Toto5.key ns-cert-type server comp-lzo verb 3 Here is the connection log with the error messages: $ sudo openvpn2 --config client.conf Wed Mar 13 22:58:22 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:22 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:22 2013 LZO compression initialized Wed Mar 13 22:58:22 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:22 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:22 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:22 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:22 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:22 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:22 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:22 2013 TLS: Initial packet from 54.234.43.171:1194, sid=ffbaf343 d0c1a266 Wed Mar 13 22:58:22 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:22 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:22 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:23 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:58:25 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:58:25 2013 PUSH: Received control message: 'PUSH_REPLY,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:58:25 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:58:25 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:58:25 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:58:25 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:25 2013 Initialization Sequence Completed ^CWed Mar 13 22:58:30 2013 event_wait : Interrupted system call (code=4) Wed Mar 13 22:58:30 2013 TCP/UDP: Closing socket Wed Mar 13 22:58:30 2013 /sbin/route delete -net 10.8.0.0 10.8.0.5 255.255.255.0 delete net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:30 2013 Closing TUN/TAP interface Wed Mar 13 22:58:30 2013 SIGINT[hard,] received, process exiting toto5:ttntec2 Dominic$ sudo openvpn2 --config client.conf --remote ec2-54-234-43-171.compute-1.amazonaws.com Wed Mar 13 22:58:57 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:57 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:57 2013 LZO compression initialized Wed Mar 13 22:58:57 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:57 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:57 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:57 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:57 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:57 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:57 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:57 2013 TLS: Initial packet from 54.234.43.171:1194, sid=a0d75468 ec26de14 Wed Mar 13 22:58:58 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:58 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:58 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:59:00 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:59:00 2013 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:59:00 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:59:00 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:59:00 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:59:00 2013 /sbin/route add -net 54.234.43.171 0.0.0.0 255.255.255.255 add net 54.234.43.171: gateway 0.0.0.0 Wed Mar 13 22:59:00 2013 /sbin/route add -net 0.0.0.0 10.8.0.5 128.0.0.0 add net 0.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 128.0.0.0 10.8.0.5 128.0.0.0 add net 128.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 Initialization Sequence Completed Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) ... The routing table after a connection WITHOUT the push redirect-gateway (all traffic is not redirected to the VPN and everything is working fine, I can ping or ssh the OpenVPN server and access all other Internet resources through my default gateway): Destination Gateway Flags Refs Use Netif Expire default user148-1.wireless UGSc 50 0 en1 10.8/24 10.8.0.5 UGSc 2 7 tun0 10.8.0.5 10.8.0.6 UH 3 2 tun0 127 localhost UCS 0 0 lo0 localhost localhost UH 6 6692 lo0 client.openvpn.net client.openvpn.net UH 3 18 lo0 142.1.148/22 link#5 UCS 2 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 50 0 en1 76 user150-173.wirele localhost UHS 0 0 lo0 142.1.151.255 ff:ff:ff:ff:ff:ff UHLWbI 0 2 en1 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSWi 0 0 en1 71 The routing table after a connection with the push redirect-gateway option enable as in the server.conf file above (all internet traffic should be redirected to the VPN tunnel, but nothing is working, I can't access any Internet ressources at all): Destination Gateway Flags Refs Use Netif Expire 0/1 10.8.0.5 UGSc 1 0 tun0 default user148-1.wireless UGSc 7 0 en1 10.8/24 10.8.0.5 UGSc 0 0 tun0 10.8.0.5 10.8.0.6 UHr 6 0 tun0 54.234.43.171/32 0.0.0.0 UGSc 1 0 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 3 6698 lo0 client.openvpn.net client.openvpn.net UH 0 27 lo0 128.0/1 10.8.0.5 UGSc 2 0 tun0 142.1.148/22 link#5 UCS 1 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 1 0 en1 833 user150-173.wirele localhost UHS 0 0 lo0 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSW 0 0 en1

  Read the article

• iCloud backup merges or overwrites?

  - by Joe McMahon

  The following happened today (it was six AM my time, so yeah, I was dumb and dropped stitches in this process): A friend had a problem with her iPhone and needed to reset it. Unfortunately she did the reset while connected to iTunes and the restore process kicked in. In my sleepy state, I told her to go ahead. She did, and restored the most recent local (iTunes) backup (from July last year - she doesn't back up often, as she has an Air which is pretty full). During setup on the phone, she was prompted to merge data with the iCloud copy, and did so. There was no "restore from iCloud" prompt. Obviously I should have made sure she was disconnected from iTunes before she did the reset, or had her set it up as a new device and then restored from iCloud, but water under the bridge now. (Side question: could I have had her disconnect and then restart the phone again and avoid this whole process?) The question is: was the "merge" that happened in this process a true merge, or a replace? Her passwords for Mail were wrong, since they were the old ones from the old backup. If she does the wipe data and restore from iCloud, will she get her old SMSes and calendar entries back? Or did the merge decide that the phone, despite it being "old" was right and therefore the SMSes, calendar entries, etc. were discarded? As a recovery option, I have a 4-day-old iTunes backup here from ~/Library/Application Support/MobileSync/Backup, but she and the phone are 3000 miles away, and it's 8GB, so I can't easily restore it for her. I do have the option of encrypting it and mailing it on a data stick if the iCloud backup is now toast. Should she try the wipe and restore from the cloud (after backing up locally), or should I just get the more-recent backup in the mail? My goal is to get everything (especially the SMSes) back to the most recent version possible.

  Read the article

• Custom PCI bracket with support, for custom PCB?

  - by newbiez

  I am considering to put a custom PCB card that I made, into my computer. It won't go on any PCI connector, it plugs in on a USB connector on the motherboard, via a ribbon cable. I need thou to plug a device to it; which means that either I leave the PCB outside the case, hanging by the ribbon (bad idea), or I could put it in a PCI slot, using a bracket. The issue is that the brackets that I have, do not have tabs, so I have no way to screw the PCB on them. I was hoping to find something that would allow me to put the PCB on it, and then just fit it in the PCI bracket opening, like this: http://www.idotpc.com/TheStore/pc/viewPrd.asp?idproduct=1203&idcategory=0 This one won't fit the bill since the holes are too close apart, compared to the one that I have already on the PCB (and can't make more holes). Do you know if there is a place where they make universal PCI bracket mounting systems for custom PCB? I just need one, so can't even order a custom one (they ask me 120 dollars for one). Thanks in advance!

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• IDE compatability with SATA image

  - by Ormis

  We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

  Read the article

• How to tell Linux to explicitly swap out main memory of a suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• How do I get a network printer installed in ubuntu 9.04?

  - by SoaperGEM

  My girlfriend's work computer now has Linux on one of the partitions, and for the most part it's running fine--except that I can't seem to get the network printers configured right. There are two of them: a Lanier MP 7500/LD275 and a Lanier MP C3000/LD430c, and Linux seems to have found them both automatically. I'll go through the steps of what I did, and what exactly went wrong. I went to Administration Printing, and clicked the new printer button. It searched for printers and found them both, listed under "Network Printers." I added them as new printers in succession. However, when I clicked "Print a Test Page," it failed saying there was a broken pipe. The device URIs were saved as socket://[ip address]:9100. I changed these to lpd://[ip address] per some online tutorial, which at first looked like it might have worked (but didn't). Then when I tried to print a test page, it first said Processing (and sometimes even Processing - printing test page, 4%, but always subsequently displays Idle - /usr/lib/cups/backend/lpd failed. Help! What do I do? It seems like Linux can find these printers just fine, and the drivers seem to be in place, so what's going wrong?

  Read the article

• Windows 7 Media Center: sometimes no sound on a TV channel

  - by torbengb

  Problem Sometimes, recorded TV shows have no sound. This is of course very annoying because the recorded show is worthless. Also, when switching channels while watching live TV, sometimes a channel has no sound. This is always solved by switching channel again and then back (most often, once will do the trick). Media Center doesn't do this trick by itself when recording of course, so that's the bigger issue - but the cause is certainly the same. Details The computer is running a newly installed Windows 7 and Windows Media Center. It has 2 different tuner-cards installed. Both are installed with signed and up-to-date Win7 drivers and appear OK in Device Manager. Both tuners get the same antenna signal, from a split cable from the wall. The cable delivers analog cable TV (40+ channels) and digital cable TV (4 channels) at the same time. Both tuners have been configured to receive both analog and digital channels. This only happens with analog channels. How can I fix the no-sound problem? Update: I've now spent some time with the computer to try and pinpoint the problem, but I've had little success so far: I flipped through the channels until one didn't have sound, then I disconnected the antenna cable from one of the tuners. It was the right one because then the video also went away. I flipped lots more channels to see if the other card also would come up mute once but I never had a channel without sound. It might still be possible, I don't know. Then I disconnected the "good" tuner and connected the "bad" tuner and again flipped lots of channels but again I never had a channel without sound. It seems to me that the problem is erratic. It happens on any channel, and I haven't ruled out yet that it only happens on one tuner.

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• How to reduce celeryd memory consumption?

  - by Gringo Suave

  I'm using celery 2.5.1 with django on a micro ec2 instance with 613mb memory and as such have to keep memory consumption down. Currently I'm using it only for the scheduler "celery beat" as a web interface to cron, though I hope to use it for more in the future. I've noticed it is the biggest consumer of memory on my micro machine even though I have configured the number of workers to one. I don't have many other options set in settings.py: import djcelery djcelery.setup_loader() BROKER_BACKEND = 'djkombu.transport.DatabaseTransport' CELERYBEAT_SCHEDULER = 'djcelery.schedulers.DatabaseScheduler' CELERY_RESULT_BACKEND = 'database' BROKER_POOL_LIMIT = 2 CELERYD_CONCURRENCY = 1 CELERY_DISABLE_RATE_LIMITS = True CELERYD_MAX_TASKS_PER_CHILD = 20 CELERYD_SOFT_TASK_TIME_LIMIT = 5 * 60 CELERYD_TASK_TIME_LIMIT = 6 * 60 Here's the details via top: PID USER NI CPU% VIRT SHR RES MEM% Command 1065 wuser 10 0.0 283M 4548 85m 14.3 python manage_prod.py celeryd --beat 1025 wuser 10 1.0 577M 6368 67m 11.2 python manage_prod.py celeryd --beat 1071 wuser 10 0.0 578M 2384 62m 10.6 python manage_prod.py celeryd --beat That's about 214mb of memory (and not much shared) to run a cron job occasionally. Have I done anything wrong, or can this be reduced about ten-fold somehow? ;) Update: here's my upstart config: description "Celery Daemon" start on (net-device-up and local-filesystems) stop on runlevel [016] nice 10 respawn respawn limit 5 10 chdir /home/wuser/wuser/ env CELERYD_OPTS=--concurrency=1 exec sudo -u wuser -H /usr/bin/python manage_prod.py celeryd --beat --concurrency=1 --loglevel info --logfile /var/tmp/celeryd.log Update 2: I notice there is one root process, one user child process, and two grandchildren from that. So I think it isn't a matter of duplicate startup. root 34580 1556 sudo -u wuser -H /usr/bin/python manage_prod.py celeryd wuser 577M 67548 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 578M 63784 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 271M 76260 +- python manage_prod.py celeryd --beat --concurrency=1

  Read the article

• RAID degraded on Ubuntu server

  - by reano

  We're having a very weird issue at work. Our Ubuntu server has 6 drives, set up with RAID1 as follows: /dev/md0, consisting of: /dev/sda1 /dev/sdb1 /dev/md1, consisting of: /dev/sda2 /dev/sdb2 /dev/md2, consisting of: /dev/sda3 /dev/sdb3 /dev/md3, consisting of: /dev/sdc1 /dev/sdd1 /dev/md4, consisting of: /dev/sde1 /dev/sdf1 As you can see, md0, md1 and md2 all use the same 2 drives (split into 3 partitions). I also have to note that this is done via ubuntu software raid, not hardware raid. Today, the /md0 RAID1 array shows as degraded - it is missing the /dev/sdb1 drive. But since /dev/sdb1 is only a partition (and /dev/sdb2 and /dev/sdb3 are working fine), it's obviously not the drive that's gone AWOL, it seems the partition itself is missing. How is that even possible? And what could we do to fix it? My output of cat /proc/mdstat: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid1 sda2[0] sdb2[1] 24006528 blocks super 1.2 [2/2] [UU] md2 : active raid1 sda3[0] sdb3[1] 1441268544 blocks super 1.2 [2/2] [UU] md0 : active raid1 sda1[0] 1464710976 blocks super 1.2 [2/1] [U_] md3 : active raid1 sdd1[1] sdc1[0] 2930133824 blocks super 1.2 [2/2] [UU] md4 : active raid1 sdf2[1] sde2[0] 2929939264 blocks super 1.2 [2/2] [UU] unused devices: <none> FYI: I tried the following: mdadm /dev/md0 --add /dev/sdb1 But got this error: mdadm: add new device failed for /dev/sdb1 as 2: Invalid argument Output of mdadm --detail /dev/md0 is: /dev/md0: Version : 1.2 Creation Time : Sat Dec 29 17:09:45 2012 Raid Level : raid1 Array Size : 1464710976 (1396.86 GiB 1499.86 GB) Used Dev Size : 1464710976 (1396.86 GiB 1499.86 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 15:55:07 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : lia:0 (local to host lia) UUID : eb302d19:ff70c7bf:401d63af:ed042d59 Events : 26216 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 0 0 1 removed

  Read the article

• Problems with USB-Devices using VDR

  - by emmsinator

  Hey Guys, I'm using VDR on vSphere4. It works sucessfully. I've already backuped several VMs with VDR and I like it very much. But now we got a problem. We have 2 VMs, using an USB-Device Server with a stick plugged in, which is definetely need by these 2 VMs for Licensing and so. Every time, I start the Backup process, the VMs lost the communication to the USB-Server and its stick after building the snapshot and while online. Because of that, the software on these VMs can't work correctly. I have to restart both Machines to solve this problem. These fact is bad for an automatic backup. Does VDR have a special function for those cases or is something like this already known? It would be no problem, to shutdown the servers for building snapshots on Saturday or Sunday. Can VDR initiate a shutdown before starting the backup process? Otherwise I must try to use scripts, but that wouldn't be so nice. Thanks a lot for your help.

  Read the article

• Installed Windows 7 Ultimate on D Drive and previous Windows 7 Enterprise on C Drive has stopped starting up

  - by teenup

  Please please help! I have installed Windows 7 Ultimate on same hard drive on D Drive on my laptop and the previous Windows 7 Enterprise which was installed on C Drive is not booting up now. When I turn on my laptop, I see two Windows 7 on the screen, when I select newer one, it starts, but when I select older one which is Enterprise edition, system won't start and I get the DOS black screen with this error message: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: Insert your Windows installation disc and restart your computer. Choose your language settings, and then click "Next." Click "repair your computer." Info: The boot selection failed because a required device is inaccessible. I notice that when I run the newer OS installed, the previous OS's drive (Which is D: now instead of C:) has become unusable and when I double click it, it asks me to format the drive. The data, that I had on my D Drive (Which is now C Drive for new OS), I had copied it to a network path and it is available. It was containing Windows 7 Users folder which I copied at that time when installing new windows. I have copied that Users folder again to the new OS's C Drive thinking it would run again, but of no use. Please please please...if someone can help...It is extremely required for me. Thanks a lot in advance.

  Read the article

• NAT via iptables and virtual interface

  - by Alex

  I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

  Read the article

• Windows 7 breaks even in safe mode

  - by delenda

  Hi, I have a Dell XPS M1730 with Windows 7 installed. I noticed last night that after a few hours of use, the fans kicked into full and I couldn't do anything without it taking forever. Minimising windows, opening device manager or even opening process explorer took minutes and a game install I had just started took nearly 4 hours to complete. When procexp finally loaded, the refresh was so slow that it was mostly useless. From what I could gather, it was reporting 60% idle processes with procexp using nearly 40%. There were no hardware interrupts listed. When I rebooted, the problem went away for about 10 minutes and then the same thing happened. The issue persists in safe mode and even after I removed the graphics drivers, which have been an issue in the past, it still happens. Icons flash quite quickly on the desktop periodically and screen refresh is painfully slow. When booting now, the fans kick in to full as soon as the windows logon box comes up and it's taking 10 minutes to bring the desktop up. Chkdsk reports nothing and the raid check says that everything is fine. I'm thinking hardware failure, probably HDD but wanted some other opinions. I'm planning to try a linux live cd to see if it works without using the hard disks. If anyone has any input, it would be greatly appreciated. Delenda

  Read the article

• ubuntu's average load never below "0.00 0.01 0.05"

  - by Karma Fusebox

  I have several ubuntu 12.04 VMs running on a ubuntu 12.04 KVM host. Those of the virtual machines that are totally idle with no services (except syslog and the other "small" standard stuff of a fresh installation) show a constant load of "0.00 0.01 0.05" in top/htop as average 1/5/15. When there are "real" applications running, the load averages behave perfectly normal but they never fall below the mentioned values. While this doesn't affect performance at all and could easily be ignored, it screws up the monitoring graphs in a very annoying way: (Notice how load15 behaves nicely if 0.05 for a short time in the right half of the pic) Unfortunately I don't know what diagnostic outputs might be helpful for you, so here's some default stuff: # top top - 16:31:01 up 1:05, 1 user, load average: 0.00, 0.01, 0.05 Tasks: 62 total, 1 running, 61 sleeping, 0 stopped, 0 zombie Cpu(s): 0.2%us, 0.2%sy, 0.0%ni, 99.2%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1019464k total, 73452k used, 946012k free, 6140k buffers Swap: 0k total, 0k used, 0k free, 22504k cached . # free -m total used free shared buffers cached Mem: 995 72 923 0 6 21 -/+ buffers/cache: 43 951 Swap: 0 0 0 . # iostat -x /dev/vda Linux 3.2.0-32-virtual (vm3) 11/15/2012 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 0.25 0.00 0.65 0.20 0.24 98.66 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util vda 0.14 0.12 0.51 0.22 6.74 1.46 22.50 0.02 23.26 20.64 29.30 7.63 0.56 Need something else? Has anyone ever seen this behavior? Might this be a bug in kvm/ubuntu/kernel 3.x in the end? Thanks a lot!

  Read the article

• Why is this iptables rule that does port forwarding not working?

  - by videoguy

  I have a server bound to localhost:7060. It is using ipv6 socket instead of ipv4. Below is netstat outout. # netstat -an Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 10.200.32.98:1720 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4122 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4123 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:4123 127.0.0.1:43051 ESTABLISHED tcp 0 0 10.200.32.98:5555 10.200.32.44:53162 ESTABLISHED tcp6 0 0 :::5060 :::* LISTEN tcp6 0 0 ::ffff:127.0.0.1:7060 :::* LISTEN tcp6 0 0 :::23 :::* LISTEN tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.142:43505 ESTABLISHED tcp6 0 0 ::ffff:127.0.0.1:43051 ::ffff:127.0.0.1:4123 ESTABLISHED tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.44:53195 ESTABLISHED udp6 0 0 :::5060 :::* CLOSE # I want to setup a port forwarding rule that accepts connections on port 24 (on all interfaces loopback as well as eth0) and forward the data to localhost:7060. This is how I am setting up the iptables rule: iptables -t nat -A PREROUTING -p tcp --dport 24 -j DNAT --to 127.0.0.1:7060** It is not working. When I telnet from different box, I see the following $telnet 10.200.32.98 24 Trying 10.200.32.98... If I change the server to bind to *:7060 and set the following rule, it seems to work fine. iptables -t nat -A PREROUTING -p tcp --dport 24 -j REDIRECT --to-port 7060 But that will make my server available on WAN interface which I don't like. I feel it had something to do with ipv6 socket (tcp6 line in netstat output). This whole thing is done on an Android device with custom built Android platform image. How do I get this working?

  Read the article

• Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

  - by William

  I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

< Previous Page | 468 469 470 471 472 473 474 475 476 477 478 479  | Next Page >