Search Results

Search found 16987 results on 680 pages for 'second'.

Page 471/680 | < Previous Page | 467 468 469 470 471 472 473 474 475 476 477 478  | Next Page >

• Dual Boot Installing Ubuntu 12.04 with Windows 7 (64) on a non UEFI system fails

  - by Randnum

  I cannot seem to install the correct boot loader for a non-UEFI firmware system. I'm trying to install Ubuntu 12.04 and Windows 7 (64) which are technically compatible with GPT but for windows only if the firmware is UEFI enabled. My system uses the old BIOS system and does not support UEFI. Therefore, whenever I finish my Ubuntu install and try to install Windows I get a "cannot install to GPT partition type" error. Even if I use Gparted to format a special NTFS file format for windows it can't handle the GPT partition style because it doesn't have UEFI. But my ubuntu install always forces GPT during installation and never asks if I want to install the old BIOS style MBR instead. How do I resolve this? Both OS's will install fine on their own the problem is when I try to install the second OS it doesn't recognize any of the other's partitions and tries to rewrite it's own on top of the other. I've tried both OS's first and always run into the same problem. Since there is no way to make Windows recognize GPT without upgrading my Motherboard how do I tell Ubuntu to use the old BIOS MBR on install? Do I have to download a special Ubuntu with a specific grub version? or should I manaually configure my partition somehow to force it not to use GPT? Thank you,

  Read the article

• exim4 seem to stop listening

  - by trakos

  Hey, I have a strange problem with my exim4 configuration. I have a dedicated server running debian for quite a long time now, but I'm not really using it actively recently, so everything just worked due to lack of changes ;) However, recently, my exim4 smtp stopped answering on port 25. It does not respond through localhost, as well - even though it's set to listen on any interface available. Some things I've checked: ks:/home/trakos/Maildir/new# netstat -ap | grep exim tcp 0 0 *:smtp : LISTEN 12521/exim4 ks:/home/trakos/Maildir/new# exiwhat 12521 daemon: -q30s, listening for SMTP on port 25 (IPv4) ks:/home/trakos/Maildir/new# cat /var/log/exim4/rejectlog ks:/home/trakos/Maildir/new# cat /var/log/exim4/paniclog The queue is set for 30s only because I was running it in a non-daemon mode to see any output. Strangely enough, no suspicious output is given, netstat even shows it is listening on port 25, but still trying to telnet to it times out. The only things that may have changed recently are: I've got second IP for my server I remember that few days ago my spamassasin crashed, and I've started it up again So yeah, I'm really clueless about this one now :P I mean, I don't even know what could be failing here. Could someone give me some ideas what should I check next? PS: it has uptime of 442 days, so I haven't really tried rebooting it yet ^^

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Slow manipulation of netfilter rules

  - by Ole Martin Eide

  I have a script maintaining gre tunnels and firewall rules using the "ip" and "iptables" tools. Setting up hundreds of tunnels, and adresses per interface runs just fine. Takes less than 0.1 second per interface, however when I get around to do the firewall rules everything slows down spending 0.5 per insertion. Why is it running so slow? What can I do to improve the speed? It seems like I could try ipset instead, but I really feel there is something wrong with the kernel or something. The interesting thing is that the first 10 rules runs fast, then it slows down.. mybox(root) foo# iptables -V iptables v1.3.5 mybox(root) foo# uname -a Linux foo 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux mybox(root) foo# cat test.sh #!/bin/sh for n in {1..100} do /sbin/iptables -A OUTPUT -s ${n} -j ACCEPT /sbin/iptables -D OUTPUT -s ${n} -j ACCEPT done mybox(root) foo# time ./test.sh real 1m38.839s user 0m0.100s sys 1m38.724s Appriciate any help. Cheers!

  Read the article

• Can't access shared folder of win8/win7 machine - Error code: 0x80004005. Unspecified Error

  - by ruslan

  It's ironic that I, software engineer with 12 years of experience, continue to have this problem from one version of Windows to another without being able to achive consistent result (sometimes it works). Here it goes again. I have a machine with Win8 Consumer Preview. It doesn't really matter that it's win8. I had same issue with win7 before. On given machine I created local admin user with same name and password I have on second PC (the machine I'm typing this from now). I have two questions to you guys. Why I'm not able to access C$ share of win8 machine from another Win7 machine? I get error that C$ doesn't exist even though it does. Why I'm not able to access share named "test" in Win8 for which Permission set to Full for Everyone. When I attempt to access it from Win7 machine I'm asked to enter username and password. After entering administrator credentials I get error "Windows cannot access \192.168.1.123\test. Error code: 0x80004005. Unspecified Error". Windows Firewall is disabled on Win8 machine for both Private and Public networks. Guest account is disabled. Built-in admin account is enabled. Machine is pingable from other machines.

  Read the article

• Rkhunter reports file properties have changed

  - by CountMurphy

  I am running a fully updated LTS copy of Ubuntu server. Today I ran rkhunter (as I do from time to time). This is the output I got: Warning: The file properties have changed: [15:52:25] File: /bin/ps [15:52:25] Current hash: f22991ec93ae966c856d367f42fc3d8a484bd827 [15:52:25] Stored hash : 1892268bf195ac118076b1b0f53e7a637eb6fbb3 [15:52:25] Current inode: 142902 Stored inode: 130894 [15:52:25] Current file modification time: 1324307913 (19-Dec-2011 07:18:33) [15:52:25] Stored file modification time : 1260992081 (16-Dec-2009 11:34:41) Warning: The file properties have changed: [15:52:33] File: /usr/bin/ldd [15:52:33] Current hash: f1e2ca5aa3a28994e2cebb64c993a72b7d97b28c [15:52:33] Stored hash : 295d9cedb121a5e431a39a6d201ecd7ce5640497 [15:52:33] Current inode: 2236210 Stored inode: 2234359 [15:52:33] Current size: 5280 Stored size: 5279 [15:52:33] Current file modification time: 1331165514 (07-Mar-2012 16:11:54) [15:52:33] Stored file modification time : 1295653965 (21-Jan-2011 15:52:45) Warning: The file properties have changed: [15:52:37] File: /usr/bin/pgrep [15:52:37] Current hash: 3eada9a96760f3e2c9111cfe32901d1432813c1d [15:52:37] Stored hash : ce265d0db9964b173fe5036f703a9b8d66e55df3 [15:52:37] Current inode: 2229646 Stored inode: 2224867 [15:52:37] Current file modification time: 1324307913 (19-Dec-2011 07:18:33) [15:52:37] Stored file modification time : 1260992081 (16-Dec-2009 11:34:41) Warning: The file properties have changed: [15:52:41] File: /usr/bin/top [15:52:41] Current hash: 6be13737d8b0950cea2f1ae3a46d4af713dbe971 [15:52:41] Stored hash : c7b495ecef3982eeb6f08a511861b1a1ae8775e6 [15:52:41] Current inode: 2229629 Stored inode: 2224862 [15:52:41] Current file modification time: 1324307913 (19-Dec-2011 07:18:33) [15:52:41] Stored file modification time : 1260992081 (16-Dec-2009 11:34:41) Warning: The file properties have changed: [15:52:53] File: /usr/sbin/cron [15:52:53] Current hash: e783ca973f970aa8a4bf5edc670e690b33914c3d [15:52:53] Stored hash : 4718257a8060736b9058aed025c992f02a74a5a7 [15:52:53] Current inode: 2224719 Stored inode: 2228839 [15:52:54] Current file modification time: 1330965568 (05-Mar-2012 08:39:28) There were also a few other I left out. Has my server been rooted? I am running fail2ban and do monitor failed ssh logins. nothing has come up. Could someone compare these hashes to their copy of Ubuntu Server (lts)? Please tell me these are false positives..... Edit: is something else like rkhunter I can run for a second scan?

  Read the article

• Optimizing Apache for large file serving

  - by D_Guy13

  I have a random problem with Apache that I can't quite figure out, here is my setup, Windows Server 2008 R2, 64 Bit, 5GB RAM, SSD with 200 MB(Read/write) and Dual Core CPU @ 2.1 GHz A dump from mod-staus, Server Version: Apache/2.4.7 (Win32) mod_limitipconn/0.24 mod_antiloris/0.5.2 PHP/5.5.9 Server MPM: WinNT Apache Lounge VC11 Server Built: Nov 21 2013 20:13:01 Current Time: Thursday, 21-Aug-2014 23:38:06 W. Europe Daylight Time Restart Time: Thursday, 21-Aug-2014 20:30:47 W. Europe Daylight Time Parent Server Config. Generation: 1 Parent Server MPM Generation: 1 Server uptime: 3 hours 7 minutes 18 seconds Server load: -1.00 -1.00 -1.00 Total accesses: 283025 - Total Traffic: 1172.2 GB 25.2 requests/sec - 106.8 MB/second - 4.2 MB/request 62 requests currently being processed, 388 idle workers Serving large .zip & iso files using mod_xsendfile. (File size range 500 MB - 1.5 GB) The setup works and is running fine. CPU usage is very unstable, jumps all the time between 10% - 90% and the servers goes down when it hits 100%. In that case I have to hard restart the server. Server it outputting traffic at 30 Mbps. Is there anything else I should think about to get a more stable CPU usage? Is that CPU usage normal? Can switching to Linux help me achieve better CPU usage?

  Read the article

• Create custom launchers in GNOME 3

  - by hochl

  I'm using Debian testing, and I have been switched to GNOME 3 by the Debian update yesterday. I'm not very comfortable with the UI. I wanted to customize everything like I had it with GNOME 2, but I simply couldn't find any way to change preferences like I'm used to. I've digged some, but all answers I could find did not help me achieve my goals. So please, if anyone knows the solution to this I'd be thankful: 1) I want several launchers that launch terminals, with different arguments and different coloring/title. I have searched everything and there seems to be no menu, no right-click, nothing which is standard in any UI I know. How can I create several launchers in this bar on the left side that launch the same application, just with different parameters? With GNOME 2 this was a piece of cake. 2) I want to switch between different terminals using ALT-TAB. Right now, I'm always just getting to the same, already-opened terminal. When I open two terminals by simply creating the second one by issuing xterm &, I still get one Terminal entry with ALT-TAB, and I have to navigate with cursor keys or mouse wheel to select one of the two xterminals. Instead, I want to open a new terminal when I click the quick launch terminal icon from the bar on the left side of the screen and navigate through them like on KDE/GNOME 2/Windows/any reasonable UI. Can this be done? 3) Is there a trick to make bluetooth devices work like on GNOME 2? Right now, my BT keyboard won't pair anymore, which, as you can imagine, makes me pretty angry. and, if anything fails: 4) How can I switch back to GNOME 2 again? :-) Honestly, who did design this? What were they smoking? I feel like I'm not allowed to do anything except start one of any application that has an icon and just with the default parameters. That can't be true, right? I feel massively restrained by this stuff :(

  Read the article

• SSH not working through Double NAT

  - by d_inevitable

  I am trying to setup port forwarding for ssh through 2 NATs The first Router translates my internet IP to my outer network (10.1.7.0). In the outer network there's a second Router that does NAT to my inner network (192.168.1.0). The target server is connected to both, the outer network and the inner network. I cannot change the port forwarding options for outer router. It is currently configured to forward the SSH and HTTP port to the router for the inner network. Internet + | v +-----------------+ +------------------+ | Outer Router | | Inner Router | |-----------------| |------------------| | | SSH HTTP | | +----+ +--------------------->| | | | | | | | | | | | | +-------+---------+ +------+---------+-+ | | | | | | | | | | | | | | +------------------+ | SSH | | | | Server | | | | | |------------------| | | | +-----------> |<-------+ | | | | |HTTP (testing) | +------------------+ | | | +------v------------------+ | | Outer Workstation | +-------------------+ | |-------------------------| | Inner Workstation| | | | |-------------------| | | | | |<----------------+ +-------------------------+ | | +-------------------+ When connecting from a outer workstation to the address of the inner router, then both SSH and HTTP work fine. When connecting from the internet to my public ip with HTTP, the connection works fine as well. However SSH just times out. Most likely because the reply is not routed back properly. I suspect its either because of the SSH itself, or because the server is connected to both, the inner and outer network. Any ideas how I could resolve this issue? The routes on the server are currently: ip route show default via 10.1.7.254 dev eth0 metric 100 10.1.7.0/24 dev eth0 proto kernel scope link src 10.1.7.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.2 Do I have to change this? If so how?

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• Apache mod_proxy

  - by mhouston100

  Uggh, I'm spewing that I can't figure this out, I'm so frustrated: <VirtualHost *:80> servername domain1.com.au ServerAdmin webmaster@localhost DocumentRoot /var/www/html ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined <Proxy *> Order Allow,Deny Allow from all </Proxy> RewriteEngine on ReWriteCond %{SERVER_PORT} !^443$ RewriteRule ^/(.*) https://%{HTTP_HOST}/$1 [NC,R,L] </VirtualHost> <VirtualHost *:443> servername domain1.com.au SSLEngine on SSLCertificateFile /etc/apache2/ssl/owncloud.pem SSLCertificateKeyFile /etc/apache2/ssl/owncloud.key DocumentRoot /var/www/html </VirtualHost> <VirtualHost *:*> Servername domain2.com.au ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / https://192.168.1.12/ ProxyPassReverse / https://192.168.1.12/ </VirtualHost> Not sure if it's clear what I'm trying to do, but I've read and read and READ, I still can't figure it out. Basically I have a working Apache server with a rewrite to force HTTPS, as seen in the first two VirtualHost entries. I now have a webmail service I set up on another server, under another domain name, however I only have one incoming public IP address. So I'm trying to have any incoming requests for the second domain to be proxied to the other server to access the webmail, whether its port 80 or 443. IMAP and POP3 are no problems, I can just forward the ports directly to the correct server. The results of the above configuration is that requests to domain2.com.au (port 80 or 443) are forwarded to https://domain1.com.au. Am I headed in the right direction?

  Read the article

• VPS Memory Exchausted Even With Light Settings

  - by user101570

  Linux noob here. I have a 256MB VPS on Ubuntu 11.04 server and when I run "free -m" the result shows all memory being used (including the second line re: buffers/cache). I found this very strange, considering I only have 5 Apache processes running each chewing up about 20MB each. MYSQL is taking up 30MB. To my knowledge, and according to "top", I have no other memory hogs operating. Settings that may be relevant: PHP memory_limit = 32M MYSQL key_buffer = 16M Prefork MPM Maxclients = 10 So when I reviewed these settings, I naturally thought maxclients was too high, so I tried switching it to 5. Now not only does my memory still show as being 100% used, my website loads much, much slower, despite not getting any traffic aside from mine at the moment. I don't understand this. I thought a single Apache process handles all requests from a client received within the "KeepAliveTimeout" window, which I've set to 2 seconds. With my initial config. of 10 maxclients, my page load times are around .3ms, so a single process should handle that no problem, correct? So next I went to an extreme level of 1 for maxclients. My memory is still at 100% usage and my site loads painfully slow. I'm a noob at a complete loss here. According to the many tutorials I've read on basic server setup, I should be good to go. Help! Please! Edit: total used free shared buffers cached Mem: 256 256 0 0 0 0 -/+ buffers/cache: 256 0 Swap: 0 0 0

  Read the article

• RESOLVED Why does IPtables's NAT stop working when I enable the firewall's third interface?

  - by Kronick

  On my firewall I've three interfaces : eth0 : public IP (46.X.X.X.) eth0:0 public IP (46.X.X.Y.) eth1 : public IP (88.X.X.X.) eth2 : private LAN (172.X.X.X) I've setup a basic NAT which works great until I turn on the eth1 interface, I basically loose the connectivity. When I turn off the interface (ifconfig eth1 down) then the NAT re-work. I've added some policy routing via iproute, which makes my three public IP's available. I don't understand why turning on eth1 on makes the LAN unavailable. PS : weirder ; when I turn on eth1 BUT remove the NAT, then the firewall is accessible by using the public IPS. So to me it's exclusively a NAT issue, since without the NAT the network works while with the NAT without the second public interface, the NAT does work. Regards EDIT : I've been able to make it work by using iproute2 rules. That was definitely a routing issue. Here is what I did : ip rule add prio 50 table main ip rule add prio 201 from ip1/netmask table 201 ip rule add prio 202 from ip2/netmask table 202 ip route add default via gateway1 dev interface1 src ip1 proto static table 201 ip route append prohibit default table 201 metric 1 proto static ip route add default via gateway2 dev interface2 src ip2 proto static table 202 ip route append prohibit default table 202 metric 1 proto static # mutipath ip rule add prio 221 table 221 ip route add default table 221 proto static \ nexthop via gateway1 dev interface1 weight 2\ nexthop via gateway2 dev interface2 weight 3

  Read the article

• One Windows Domain workstation can ping gateway but gets no internet access

  - by dindeman

  One of the (Windows XP SP3) workstations of our Windows Domain could not access internet anymore, this problem suddenly happened overnight. The domain controllers (there are three of them) are all running Windows Server 2008. First I compared the output of ipconfig /all on the faulty workstation with the output of a working workstation and it was just fine as it had always been. In particular the default gateway was correct and always remained pingable from the faulty workstation. I guessed that something was wrong with the DHCP service and I restarted the DHCP server service on all of our three DCs as well as the DHCP client service on the faulty workstation. This didn't solve the issue. I then thought of renewing the DHCP lease with ipconfig /release and ipconfig /renew and here is my first question: why did this never work? The same IP address (192.168.0.45) kept being assigned despite all my attempts to renew it (note that all our workstation are getting their TCP/IP automatically.) Even by leaving the domain and changing the computer name the same address was yet again obtained... Anyway I then proceeded to switch the TCP/IP configuration for that machine manually to another free valid IP address (192.168.0.41)... and then the internet access came back! I then cleared any traces of the previous IP in the DHCP leases list and in the DNS tables of our DCs and, after setting back the TCP/IP configuration to 'automatic', finally, the new lease would be granted (192.168.0.41) alongside with the internet access. My second question: what went suddenly wrong with the original IP address?

  Read the article

• How to safely send newsletters on VPS (SMTP) w/ non-hosted domain as "From" email?

  - by Andy M

  Greetings, I'm trying to understand the safest way to use SMTP. I'm considering purchasing a second virtual server mainly for email sending, on which I will set up PHPlist (a free open-source mailing program), so we have the freedom to send unlimited newsletters (...well, 10,000 per day at least, which requires a VPS rather than shared hosting). Here's my current setup with a paid mass-mailing software: I have a website - let's call it MyHostedDomain.org. I send newsletters with the From / Reply To address as [email protected], which isn't being hosting by me but I have access to the email account. Can I more or less safely set this up with an SMTP server on a VPS? i.e. send messages using [email protected] as the visible address, but having it all go through my VPS SMTP? I cannot authenticate it, right? Is this too risky a practice? Is my only hope to use an address with a domain on the VPS, i.e. [email protected]? I already have a Reverse DNS record for the domain hosted on my current VPS. I also see other suggestions, like SenderID and DKIM. But with all these things combined, will this still work? I don't want to get blacklisted, but the good thing is this is a somewhat private list, and users opt-in to subscribe. So it's a self-made audience. (If it makes you feel better, this is related to a non-profit activity, not some marketing scam...it's for a good cause, I assure you!)

  Read the article

• FTP account ownership on vhost directory makes Apache not run website correctly

  - by CodeShining

  I've purchased a virtual server, where I'm given of a non-root sudo-enabled user. Actually I do need to create an FTP account that's not that sudo-able account, so I created a no-login account just for that purpose. I've set up VSFTPd correctly, also enabling the "userlist" feature, to specify which user are permitted to use FTP. Then I created an empty directory under my sudo-able account, and I gave ownership permissions to the second account, so to make it more easy to understand, let's say the main account (the one I do use to manage my VPS) is called ubuntu and the FTP-user is named ftpuser, I created a directory /home/ubuntu/mywebsite giving the ownership to ftpuser:ftpuser. Then I uploaded a worpdress website, whose default permissions are 755 and 644. The issue is that Apache is not given of any privilege to run the website. How can I make the website run properly, and which is the most secure? Should I run that virtualhost with another user (if it's possible)? Should I force the FTP user to use the www-data group (if that's possible) and run with permissions like 775 and 664? How can I solve this issue? Any help is appreciated, I'd like to run it using the default permissions, so any update won't break up anything (because of permissions reset).

  Read the article

• Figuring out which PC part is faulty

  - by Davy8

  I have an odd scenario and I'm having trouble figuring out which is the faulty component. First of all, the video doesn't work, monitor says it's not getting a signal. Monitor's not faulty (works on other computer) so the first suspect was video card. However 2 things make me think it's not the video card. (Don't have another machine with PCIe around to test definitively) First, the GPU fan is spinning so it's getting power. Second, tried putting in an older PCI video card that is known to be working (pulled out of another working machine) and there's still no video. Normally if it's not the video card I'd suspect the motherboard, but everything's getting power on the mobo, so I'm not sure. The case apparently doesn't have system speakers, so can't hear any of the diagnostic beeps either. Also not sure whether a faulty CPU would cause no image at all either. The parts are brand new so something's going to get RMA'd but I'm not sure which component is to blame in this case. (Only slightly related, but I also accidentally put too much thermal paste on the CPU. The fan/heatsink instructions said to put the whole tube which seemed like a lot compared to previous experience, and as I started squeezing I knew it was definitely too much and stopped at about 1/3 but against my better judgement I didn't wipe any off. I'm not sure whether that would cause problems other than not cooling as effectively as it should)

  Read the article

• How can I read PDFs with e-reader on a Lenovo tablet?

  - by Jack M

  This is my first time using a tablet and I'm totally lost - this must be what computers look like to old people. This is a Lenovo Thinkpad tablet. I don't see a specific model number on it (it was passed down to me second hand). What I'd like to do is read a PDF. I'm fairly certain I successfully transferred the PDF onto the tablet via an SD card, and I noticed this thing has an app called "eReader" on it, so I started that up. All I see are empty bookshelves, and no obvious buttons or settings anywhere. I saw in multiple places that you have to, as one site puts it: ...copy and paste the relevant files into the eBooks folder and they will appear on the eReader shelf for your consumption... But I have no idea how to: Access the file system. Locate the eBooks folder. Copy and paste files. Will I need a file explorer app? If so, how can I install that given that my only method of getting data onto this tablet is an SD card (no wireless internet).

  Read the article

• System randomly freezes yet mouse still moves, SSD out of reallocatable sectors, should I replace it?

  - by user784446

  This problem has lasted for the past 48 hours. The first time it happened, a program I was running stopped responding, so I tried to end it from task manager. The processes at first were listed fine until hovered upon. Eventually, despite the mouse still being able to move, after a few persisting clicks the mouse finally stopped moving. The screen went blank shortly thereafter. The second time it occurred, items on the screen stopped responding - hovering over the taskbar or such wouldn't elicit a response. Sound would still play however. Eventually, the mouse became unresponsive and the system restarted itself. I suspect that it may be a problem of my SSD drive. After looking through some Google search results, I downloaded HDTunePro to determine if there's a problem with the drive. Results returned a problem of reallocated sector count. An error scan also revealed 48 bad sectors. Also, an attempt to backup the contents of the most important areas of the drive returned a few explorer "Error: cannot read source from disk" errors. Should I ditch the drive and use another drive or is there anything that can be done to repair the drive? SSD: OCZ Petrol 64gb CPU: AMD Athlon II X4 640 RAM: Generic 3GB DDR2 Motherboard: Gigabyte MA74GM-S2H OS: Windows 7 Ultimate x64 Thanks!

  Read the article

• ddwrt client brigde acces point lost

  - by llazzaro

  Ok I have an AP with ddwrt firm (i know its not the best, but continue reading!) AP is configured to work like a wifi "transparent" brigde, also it had a virtual wifi network card to expand radius of wifi signal in that same AP. The brigde is working, computers behind AP gets ips from main routers which shares internet....BUT! I cant access webgui of the bridge AP... Main problem : AP is lost, but its working as brigde. I cant find it in the network (it didnt have any ip!) so I cant change any configuration... First solution : Reset AP, but it cannot be done. Reset button dont works due to a bug in ddwrt micro firm that mi linksys WAP54g had installed (I really hate this firmware I like more openwrt that my main router has) Second Solution : arp -a from main router , from computers behind AP...It dont appears in the list. Any more ideas, the router at some level must be there, the brigde is working. I know its possible that the AP is with an ip like 192.168.100.2 , my subnect actually is 172.16.X.X. :) thanks!

  Read the article

• Extend Linux Desktop to another X Windows Display

  - by unknown (google)

  Hello, I am a long time Linux user of the Xinerama and other technologies for extending a desktop to multiple monitors. However when I travel with my laptop I miss the multi-monitor support I enjoy at home. Recently I acquired a second laptop for a low price. Both laptops are running Fedora (versions 10 and 11 respectively). I use Gnome as my primary desktop environment. I know about synergy. I use synergy all the time to control the screen of other Windows / Linux systems I use. I would like to know, can I sit both my primary and secondary laptops together and achieve a Xinerama-like extended desktop environment? Ideally I would like to start a GNOME session on my primary laptop. And then start a X-Windows Desktop on my secondary laptop and extend my primary laptop's desktop onto it. I would like to be able to move Windows from the primary desktop to the secondary laptop desktop. Would I need to use synergy to do this with some other bit of X-Windows technology? Or is there X-Windows technology that will do all this for me? I am familiar with X Windows ability to display applications remotely. I am also familiar with Nomachine's NoX.

  Read the article

• Certificates in SQL Server 2008

  - by Brandi

  I need to implement SSL for transmissions between my application and Sql Server 2008. I am using Windows 7, Sql Server 2008, Sql Server Management Studio, and my application is written in c#. I was trying to follow the MSDN page on creating certificates and this under 'Encrpyt for a specific client', but I got hopelessly confused. I need some baby steps to get further down the road to implementing encryption successfully. First, I don't understand MMC. I see a lot of certificates in there... are these certificates that I should be using for my own encryption or are these being used for things that already exist? Another thing, I assume all these certificates are files are located on my local computer, so why is there a folder called 'Personal'? Second, to avoid the above issue, I did a little experiment with a self-signed assembly. As shown in the MSDN link above, I used SQL executed in SSMS to create a self-signed certificate. Then I used the following connection string to connect: Data Source=myServer;Initial Catalog=myDatabase;User ID=myUser;Password=myPassword;Encrypt=True;TrustServerCertificate=True It connected, worked. Then I deleted the certificate I'd just created and it still worked. Obviously it was never doing anything, but why not? How would I tell if it's actually "working"? I think I may be missing an intermediate step of (somehow?) getting the file off of SSMS and onto the client? I don't know what I'm doing in the least bit, so any help, advice, comments, references you can give me are much appreciated. Thank you in advance. :)

  Read the article

• 150 TB and growing, but how to grow?

  - by seandavi

  My group currently has two largish storage servers, both NAS running debian linux. The first is an all-in-one 24-disk (SATA) server that is several years old. We have two hardware RAIDS set up on it with LVM over those. The second server is 64 disks divided over 4 enclosures, each a hardware RAID 6, connected via external SAS. We use XFS with LVM over that to create 100TB useable storage. All of this works pretty well, but we are outgrowing these systems. Having build two such servers and still growing, we want to build something that allows us more flexibility in terms of future growth, backup options, that behaves better under disk failure (checking the larger filesystem can take a day or more), and can stand up in a heavily concurrent environment (think small computer cluster). We do not have system administration support, so we administer all of this ourselves (we are a genomics lab). So, what we seek is a relatively low-cost, acceptable performance storage solution that will allow future growth and flexible configuration (think ZFS with different pools having different operating characteristics). We are probably outside the realm of a single NAS. We have been thinking about a combination of ZFS (on openindiana, for example) or btrfs per server with glusterfs running on top of that if we do it ourselves. What we are weighing that against is simply biting the bullet and investing in Isilon or 3Par storage solutions. Any suggestions or experiences are appreciated.

  Read the article

• Obtaining clear cable signal with Hauppage 1191-950Q TV Tuner

  - by Kyle B.

  I bought a Hauppauge 1191 WinTV-HVR-950Q TV Tuner a while back, and I am attempting to use it to watch TV in Windows Media Center. I do not have cable TV, however I used to have Comcast. Through experimentation, I found that connecting my coax cable into my TV, I was able to view television (i.e. 2-1 = CBS, 5-1 = NBC, etc). This also works on a second TV I use in another room. When I connect the coax cable to my TV Tuner stick and scan TV channels in Windows Media Center, it only picks up 1 station (like 81 or something). My only conclusion on this is somehow the hardware in the television is decrypting a signal that the TV tuner stick is not able to. Is that possible? Should I try a different TV tuner? Any assistance would be appreciated. I also bought a Terk HD Indoor Antenna but my reception has been flakey, so I would rather go this route if possible.

  Read the article

• Any ideas why Ettercap filters aren't seeing packet data?

  - by Bryan

  I'm using an Ettercap filter to detect a query response coming back from a particular service on a remote machine. When I see a response from the service, I'm searching through the data in the packet to see if an offset is a specific value, and if so I'm changing the value at another offset. Trouble is, when I try this on a new virtual machine I built my Ettercap filter's no longer getting any data in the DATA.data variable available to it. if(ip.proto == TCP && tcp.src == 17867) { msg("Response seen!\n"); if(DATA.data + 2 == "\0x01") { msg("Flag detected!\n"); DATA.data + 5 = 0x09; } } The filter's getting applied to the traffic because "Response seen!" messages get printed out by Ettercap. However, "Flag detected!" messages do not. I think DATA.data is indeed empty because if I change my second "if" statement to check for DATA.data == "" then the "Flag detected!" message gets printed. Any ideas why this may be happening?! Also, if this is the wrong site to be asking questions like this, please let me know. I wasn't sure if it fit better here or somewhere like superuser or serverfault. By the way, this is a cross-post from StackOverflow... I should have posted on this forum instead I think. :)

  Read the article

< Previous Page | 467 468 469 470 471 472 473 474 475 476 477 478  | Next Page >