Search Results

Search found 14828 results on 594 pages for 'settings py'.

Page 496/594 | < Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >

  • Best usage for a laptop being used as a desktop without removable batteries

    - by Senseful
    After reading the information on http://batteryuniversity.com, I realize that one of the best ways to permanently damage a lithium ion battery is to use the battery at a high temperature while it's fully charged. This is exactly what happens when you use the computer as if it were a desktop computer, since leaving it plugged in will keep the battery at 100% and using the computer will heat up the battery. This is why it's recommend to remove the battery from your laptop if you are using it is this scenario. My question is what would you do if the laptop doesn't have removable batteries (e.g. a MacBook Pro)? Should I use some kind of charge cycle such as: charge to 80%, unplug the power chord, use the laptop until it reaches 20%, then repeat the cycle by charging to 80% again? If so, which values should I use instead of 80% and 20%? (I think charging to 80% is better than 100% because of the damage that a hot battery at 100% can do, but I just made the figure 80% up, and I'm sure there's a better number to strive for which is backed by science.) I've read many of the articles on batteryuniversity.com, but couldn't find anything pertaining to this. Update: What about doing something like charge (or discharge) it to 50%, then plug it in and turn on settings which use the battery as much as possible (e.g. brightness all the way up, wi-fi on, etc.), in order to try to maintain the battery at 50% (i.e. the rate it is charging is the same as it is discharging). This will probably heat up the battery, but would make it so you don't need to constantly plug and unplug the laptop. The one bad thing is that you are taking up more charge cycles which would decrease the battery life, thus I'm not sure this is a good idea.

    Read the article

  • What to do when a device has no driver for Windows 7 but it has Vista, XP drivers

    - by Mehper C. Palavuzlar
    This has always been a bothersome matter for me. Some devices (printers, scanners, etc.) have drivers for older versions of Windows (Vista, XP, 2000, NT) but no driver for Windows 7. What are my chances to install such devices on Windows 7? Example case: I have a Sharp printer & scanner (Sharp AR-122E N) which I have used for my old Windows XP based PC. Now I want to install it on a Windows 7 x64 based PC. Windows 7 cannot load its driver. I used the original driver CD but when I run the setup.exe (which is included in AR122EN111.exe, 6713KB), it says Cannot install driver on this operating system. Supported operating systems are: Windows 2000, XP, Vista. I tried to install the driver using compatibility settings. I tried Windows Vista and Windows XP SP3, but to no avail. The setup gave the same error. I also googled for Windows 7 driver for "Sharp AR-122E N" but it only listed the original driver that I tried. The official site of Sharp does not even list the driver for this product. In the past, the compatibility setting workaround did work for some devices, but this time it failed. What else can I do to overcome this problem?

    Read the article

  • Issues regarding internet connectivity

    - by andySF
    Hello. My problem started when Yahoo Messenger stopped connecting. I've tried to see if Internet Explorer was working but will not load any page. The diagnostics of Internet Explorer says that is something wrong with my dns(using just ip of google or yahoo or my local webserver was not working). I use Windows 7 and at the moment i've had Internet Explorer 8 and after a lot of failing updates to ie9 I've successfully install the Romanian version of IE9(now i have ie8 after a system restore). Then I installed the service pack 1. I've done a lot of things and I will try to enumerate them, but my problem persists. Settings from Yahoo Messenger and Internet Explorer are OK. I've try to reset winsock and ip from netsh. I've scanned my pc with spybot, mallwarebytes, Trojan Remover(simplysup), Loaris Trojan Remover, Avast, Nod32, Kaspersky, Bitdefender,alot of registry cleaner including CCleaner and maybe others that I cannot remember now. I reset the registry permissions using subinacl. At a moment my files permissions was set jut to "trusted installer" and I've put the permission back to files and folders using the model of other windows 7 machine. I have try so many things that now i'm stuck in a loop using different security tools to check for problems. Oh, and my virtual machines are working just fine.(I'm using VirtualBox) Please Help. PS, Reinstalling Windows is not an option. Thank you!

    Read the article

  • legitimacy of the tasks in the task scheduler

    - by Eyad
    Is there a way to know the source and legitimacy of the tasks in the task scheduler in windows server 2008 and 2003? Can I check if the task was added by Microsoft (ie: from sccm) or by a 3rd party application? For each task in the task scheduler, I want to verify that the task has not been created by a third party application. I only want to allow standards Microsoft Tasks and disable all other non-standards tasks. I have created a PowerShell script that goes through all the xml files in the C:\Windows\System32\Tasks directory and I was able to read all the xml task files successfully but I am stuck on how to validate the tasks. Here is the script for your reference: Function TaskSniper() { #Getting all the fils in the Tasks folder $files = Get-ChildItem "C:\Windows\System32\Tasks" -Recurse | Where-Object {!$_.PSIsContainer}; [Xml] $StandardXmlFile = Get-Content "Edit Me"; foreach($file in $files) { #constructing the file path $path = $file.DirectoryName + "\" + $file.Name #reading the file as an XML doc [Xml] $xmlFile = Get-Content $path #DS SEE: http://social.technet.microsoft.com/Forums/en-US/w7itprogeneral/thread/caa8422f-6397-4510-ba6e-e28f2d2ee0d2/ #(get-authenticodesignature C:\Windows\System32\appidpolicyconverter.exe).status -eq "valid" #Display something $xmlFile.Task.Settings.Hidden } } Thank you

    Read the article

  • Disable RAID to JBOD in server IBM x3400 M2

    - by BanKtsu
    Hi I just wanna disable the default RAID in my server IBM System X3400 M2 Server(7837-24X),i have 3 disk drives SAS. I want to make them a JBOD "Just a Bunch Of Disks", because I want to install in the drive 0 CentOS, and the other two make them cache files for a squid server. I disable the RAID in the BIOS: System Settings/Adapters and UEFI drivers/LSI Logic Fusion MPT SAS Driver -PciRoot(0x0)/Pci(0x3,0X0)/Pci(0x0,0x0) LSI Logic MPT Setup Utility RAID Properties/Delete Array Later I boot the CentOS live CD and install the OS in the drive 0, and the others 2 mounted like this: *LVM Volume Groups vg_proxyserver 139508 lv_root 51200 / ext4 lv_home 84276 /home ext4 lv_swap 4032 Hard Drive sdb(/dev/sdb) free 140011 sdc(/dev/sdc) free 140011 sdd(/dev/sdd) sdd1 500 /boot ext4 sdd2 139512 vg_proxyserver physical volume(LVM) But when I restart the server give me the error: Boot failed Hard Disk 0 UEFI PXE PciRoot(0x0)/Pci(0x1,0X0)/Pci(0x0,0x0)/MAC(001A64B15130,0X0)) ........PXE-E18:Server response timeout. UEFI PXE PciRoot(0x0)/Pci(0x1,0X0)/Pci(0x0,0x0)/MAC(001A64B15132,0X0)) ........PXE-E18:Server response timeout. and the OS not start. The IBM force me to do a RAID?,why?

    Read the article

  • IRC server connecting to another server

    - by Oxinabox
    I'm setting up an IRC server using IRC-Hybrid, I want my server to connect to another server, so that people on my server can connect to channels on that other server. I know this can be done, the GIMP IRC, is the same as the GNOME IRC My ircd.conf contains the following: connect { name = "aabstractname"; host = "128.64.2.1; send_password = "somepass"; accept_password = "somepass"; encrypted = no; port = 6667; class = "server"; autoconn = yes; compressed = yes; fakename = "irc.sd.dom.asn.au"; }; So when i run: /etc/init.d/ircd-hybrid restart it should be connecting to 128.64.2.1, but the log on 128.64.2.1, doesn't show anything Do I need entry on the host 128.64.2.1? I can't find any documentation for ircd.conf I'ld really like that documentation so I can check all my settings are right.

    Read the article

  • Using my own Postfix, filtering spam and getting all the mail into my ISP's inbox

    - by djechelon
    Hello, I currently own a domain bought via GoDaddy.com, which provides me a basic email setup for the most common needs. I configured it to forward all mail to [email protected] to [email protected]. I also own a virtual server with a running Postfix that I use for a specific website (all mail to somedomain.com gets forwarded via LMTP to a program written by me). Since I'm recently experiencing some harassing by spammers, since GoDaddy doesn't seem to filter spam, and since my Windows Phone's Pocket Outlook cannot filter spam, I would like to use SpamAssassin to filter inbound spam by changing my domain's MX records to my server My ideal setup is the following: All mail delivered to somedomain.com gets redirected via LMTP as usual via virtual transport without any spam check All mail to [email protected] gets redirected to [email protected] after a severe spam check I don't care about [email protected] since I use just one address for now I would like to train SpamAssassin with customized spam rules, possibly based on the presence of certain keywords (links to certain unsubscribe pages I found recurring) I currently configured Postfix with transport somedomain.com lmtp:[127.0.0.1]:8025 .somedomain.com error: Cannot accept mail for this domain relay somedomain.com OK (I guess I should add mydomain.com OK too) virtual @mydomain.com [email protected] (looks like a catch-all rule, it's OK as requirement 3) I installed SpamAssassin, I can do rcspamd start and set it to boot with the server, but I don't know if there is anything else to do for use in Postfix, and how to apply requirement 1 (only mail to mydomain.com gets filtered) I also tried to send an email via Telnet to make sure my settings are ready for MX change. I received the message into my account but I found that it gone through secureserver.net, like Postfix didn't rewrite the destination but simply relayed the message. Thank you in advance. I'm no expert in SpamAssassin, and I have little experience in Postfix (enough to avoid making my server an open relay)

    Read the article

  • Samba Does Not List Files In Shared Directory

    - by Sean M
    I am running Samba on a CentOS server, and I am experiencing a problem where it allows me to connect to the server and see a share, but shows the share as an empty directory. I find this behavior strange. Here is the stanza in my smb.conf for the given share: [seanm] path = /home/seanm writeable = yes valid users = seanm, root read only = No Here's what I see on the server side: [seanm@server ~]$ ls -l -rw-r--r-- 1 seanm seanm 40 Jan 4 13:45 pangram.txt And yet: [seanm@client ~]$ smbclient //server/seanm -U seanm -W WORKGROUP Enter seanm's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.33-3.29.el5_5.1] smb: \> ls . D 0 Fri Jan 7 10:08:55 2011 .. D 0 Fri Jan 7 07:58:31 2011 58994 blocks of size 262144. 50356 blocks available This behavior is present on both a Windows client and a Linux client system. The behavior is present with the firewall on and with the firewall off, so it's not that. Neither /var/log/messages nor /var/log/secure have any complaints about Samba. I doubt that SELinux is a problem: just in case, here are the relevant settings. [root@server ~]# getsebool -a | grep samba samba_domain_controller --> off samba_enable_home_dirs --> on samba_export_all_ro --> off samba_export_all_rw --> off samba_share_fusefs --> off samba_share_nfs --> off use_samba_home_dirs --> on virt_use_samba --> off What am I doing wrong here, and what can I do to fix it?

    Read the article

  • How to merge arbitrary snapshot into base vdi in Virtualbox

    - by jmathew
    I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid <path/to/vdi> Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID?

    Read the article

  • HP DL185 - very slow disk read speed

    - by fistameeny
    Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

    Read the article

  • Desktop Provisioning for a Small Linux Software Development Team

    - by deakblue
    Goal: Get a small team using a standard development image rather than 4 software devs setting up their own environments. Why: it takes a day or days to install a distro, build-specific libraries, tools like editors and IDEs, mysql, couchdb, java, maven, python, android-sdk, etc. It's a giant PITA that when repeated 4 times by 4 developers (not sys admins) wastes time and generates annoying divergences that crop up later (it-builds-on-my-box syndrome). There's no sharing of productivity, settings, tricks, scripts, set-ups. Some of this is helped by segregating the build systems into headless virtualbox images. This doesn't really address tooling though or the GUI-desktop dev that needs doing. So I see three basic strategies, ghosting, virtualization, and finally creating a kind of in-house linux distro (I guess Google does something like this). The target dev environment is based on Debian OpenBox and must allow a mix of 3rd gen Core i7 notebooks 8GB-minimum to work both single and multihead. Important, the lappies are not the same, but a mix of 2012 macbooks and PCs. So: virtualization: is doing all of your work within a VM, like VirtualBox, practical on this hardware or annoying. ghosting: will laptops from different manufacturers make this impractical. DIY distro: short of scripting a bunch of package installs, I don't know if there's any "distro-maker" that could keep this from being an epic project of scripting package installs. So any advice?

    Read the article

  • SharePoint web services not protected?

    - by Philipp Schmid
    Using WSS 3.0, we have noticed that while users can be restricted to access only certain sub-sites of a site collection through permission settings, the same doesn't seem to be true for web services, such as /_vti_bin/Lists.asmx! Here's our experimental setup: http://formal/test : 'test' site collection - site1 : first site in test site collection, user1 is member - site2 : second site in test site collection, user2 is member With this setup, using a web browser user2 can: - access http://formal/test/site2/Default.aspx - cannot access http://formal/test/site1/Default.aspx That's what is expected. To our surprise however, using the code below, user2 can retrieve the names of the lists in site1, something he should not have access to! Is that by (unfortunate) design, or is there a configuration setting we've missed that would prevent user2 from retrieving the names of lists in site1? Is this going to be different in SharePoint 2010? Here's the web service code used in the experiment: class Program { static readonly string _url ="http://formal/sites/research/site2/_vti_bin/Lists.asmx"; static readonly string _user = "user2"; static readonly string _password = "password"; static readonly string _domain = "DOMAIN"; static void Main(string[] args) { try { ListsSoapClient service = GetServiceClient(_url, _user, _password, _domain); var result = service.GetListCollection(); Console.WriteLine(result.Value); } catch (Exception ex) { Console.WriteLine(ex.ToString()); } } private static ListsSoapClient GetServiceClient(string url, string userName, string password, string domain) { BasicHttpBinding binding = new BasicHttpBinding(BasicHttpSecurityMode.TransportCredentialOnly); binding.Security.Transport.ClientCredentialType = HttpClientCredentialType.Ntlm; ListsSoapClient service = new ListsSoapClient(binding, new System.ServiceModel.EndpointAddress(url)); service.ClientCredentials.UserName.Password = password; service.ClientCredentials.UserName.UserName = (!string.IsNullOrEmpty(domain)) ? domain + "\\" + userName : userName; return service; } }

    Read the article

  • Win Svr 2003 DHCP Bad Addresses

    - by VinceM
    After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

    Read the article

  • Trouble printing to local printer when connected to VPN with split-tunneling enabled

    - by Marve
    I'm a volunteer network admin for a multi-tenant non-profit office space. One of our new tenants uses a VPN to connect to remote resources using RRAS and Small Business Server 2008. They also have a local network printer for the workstations in our office. When connected to the VPN, they cannot print to the local printer. I informed their network admin that they need to enable split-tunneling to fix this. Their network admin enabled split-tunneling, but apparently printing still didn't work. He told me that I need to open port 1723 on our office firewall to allow it to work. I'm just a novice administrator and not familiar with RRAS, but this doesn't sound right to me and I haven't been able to find anything on the web to validate it. Additionally, my understanding of split-tunneling is that it is handled entirely by the VPN client and should work irrespective of firewall settings. Is my understanding of the situation incorrect? What steps should I take to resolve this problem?

    Read the article

  • MS Excel 2010 - Using DSN + 32 bit drivers

    - by Kristiaan
    I need some advice as im running into a problem and so far i have been unable to find a solution. We have a set of reports developed in MS Excel that use DSN file to connect to data sources to retrieve data, these work fine on 32 / 64bit systems, however we are moving to a terminal server environment using windows 2008 R2 64Bit. The reports fail to run using the DSN's within this environment if we only have the 32bit drivers installed and configured in the ODBC settings, the minute we install the 64Bit drivers the software works. Is there a way / Method of getting Excel or the DSN file to NOT use the 64Bit driver, but force it to use the 32bit driver. ANSWERED - But due to low user score i cannot "answer" my own question... Sadly there is no way to-do what i want to-do, without a lot of very nasty and not 100% perfect reg hacks. If you need to access 32bit ODBC data sources the application in question has to be 32Bit. here is a link to just one forum post i found relating to this type of problem, it appears the only way i would be able to accomplish this is to remove the 64bit version of office and install the 32bit version instead of it. http://social.msdn.microsoft.com/Forums/en-US/accessdev/thread/5108f337-f06a-4518-afe3-d3c1abd040ef/

    Read the article

  • Games, Windows 8.1 and 144Hz display

    - by Marioysikax
    So I have been having problems with few games after switching from 7 to 8.1, which seems to be related to my 144Hz monitor. Few examples: Shank, Shank 2, Blood of the Werewolf, Astebreed, the Sims 2 and Rayman Legends patch 1.2Had few other as well but it's been long and I have 600+ steam library. From those games at least the Sims 2 and Shank worked without any problems with same setup and Windows 7. So basically these games simply refuse to launch with basic setup. However if I plug 60Hz TV with HDMI instead everything magically starts to work. As for Astebreed and the Sims 2 using windowed mode seems to also work. As for Rayman Demo and version 1.0 works for some reason and 1.2 breaks settings menu. I have already tried contacting supports. EA support stated game simply shouldn't work with 8.1 at all (which is lie as it works with that TV and friend with 8 plays just fine), ubisoft support took few weeks and support said he will forward info for further processing, blood of the werewolf support had no idea what's going on and told me to just use my TV instead.Changing monitors refresh rate to 120Hz or forcing it to 60Hz doesn't do anything. I have DVI right now but I will try with DisplayPort when I get the cable. At PCGW Garrett said it may have something to do how listing resolutions work with 8 compared to earlier Windows versions but my googling skills don't bring anything up and compatibility mode for earlier windows version doesn't work either (not that I expected that to work). My system specs are on my steam profile. How do I get those work with my 144Hz monitor as well as possible future games having same problem? Downgrading to 7 would work but is far from practical and I don't own legit lisence for that one.

    Read the article

  • diskmgmt.msc: Cannot delete volume from USB

    - by Notinlist
    I have an USB drive with about 8GB of size. It has a single partition of size 169MB. Don't know why, I got it that way. I wanted to delete this small (FAT32) partition and create a single NTFS volume on it. First, I noticed that the "Delete volumme" option is disabled (grayed out). I then tried "Change drive letter and paths..." and removed "F:", that way I made sure that there are no open files on it. The "Delete volume" was still disabled. Then I got suspicious, and right clicked on the "Unallocated" area and I noticed that I did not have any useful option. All "New * volume" items are disabled. I exited from diskmgmt.msc, ran a cmd.exe with administrator privileges, ran the diskmgmt.msc from it, same experiences. Why can't i do anything with this disk? I've read some advices about downloading some alternative free software, but I rather not do it if possible. I still hope that Windows 7 Enterprise 64bit alone can reinitialize an USB drive without external help. I also cannot do anything with my other 8GB pendrive. It's all an NTFS volume, I tried to delete it, but the option is disabled here too. Maybe I have some settings somewhere that prevents my from partitioning USB disks. (I have the freedom to remove my D: partition which is the second - not counding the "System reserved" - on my SSD disk.)

    Read the article

  • How do I fix error 1303 during TI Connect install?

    - by smoth190
    I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

    Read the article

  • Backup Exec tape rotation guidelines

    - by HannesFostie
    Hi We use Backup Exec to take care of our backups for our data server, exchange server, and one more set of systems. Each of these 3 is being done on a separate "set" of tapes. Our goal is to be able to roll back a full 2 weeks, with 1 full backup each weekend and differential/incremental backups in between (the difference between the two in our case isn't very big, because the employees mostly use a very similar set of files throughout the week). While playing around with the settings on how to achieve this, we set the time for BE to keep the full backup to 14 days, but because we have too much data this would require manual intervention each time to erase a certain tape and use that. What I would like to know is what kind of guidelines, tricks, tips and general "stuff to think about" you keep in mind when designing your backup schedule. The type of backups (full/diff/incr) isn't of that much importance in our case as it's more or less set in stone. Made this community wiki as it's not a very specific question. Thanks in advance!

    Read the article

  • How to Set up MySQL Server to utilize more memory

    - by Cyril Gupta
    Hi there, I have MySQL setup on Windows along with Plesk. The version is 5.0.45 Community. The databases I have on the server are MyISAM as well as InnoDb, but predominantly innodb. I had 8G memory on my server, but MySQL isn't going up more than 1.3G and tweaking the settings isn't helping. I tried to increase the memory allocation for innodb_buffer_pool_size, it works if I set it up to 1G, but if I set 2G, or above the server doesn't come back online! I want mySQL to use at least 5-6 Gigs of the memory I have for performance, but I can't get this to work. Can anyone please help? My mysql config file is below (there are 2 mysqld sections... when i used MySQL workbench it created another one!) [MySQLD] port=3306 basedir=C:\\Program Files (x86)\\Parallels\\Plesk\\Databases\\MySQL datadir=C:\\Program Files (x86)\\Parallels\\Plesk\\Databases\\MySQL\\Data default-character-set=latin1 default-storage-engine=INNODB query_cache_size=128M table_cache=1024 tmp_table_size=32M thread_cache=32 myisam_max_sort_file_size=100G myisam_max_extra_sort_file_size=100G myisam_sort_buffer_size=2M key_buffer_size=32M read_buffer_size=16M read_rnd_buffer_size=2M sort_buffer_size=8M innodb_additional_mem_pool_size=24M innodb_flush_log_at_trx_commit=1 innodb_log_buffer_size=10M innodb_buffer_pool_size=1G innodb_log_file_size=10M innodb_thread_concurrency=8 max_connections=700 key_buffer=48M max_allowed_packet=5M sort_buffer=2M net_buffer_length=4K old_passwords=1 wait_timeout=20 connect_timeout=60 [client] port=3306 [mysqld] query_cache_min_res_unit = 4096 innodb_additional_mem_pool_size = 1048576 innodb_buffer_pool_size = 1G query_cache_limit = 1048576 key_buffer_size = 8388608 sort_buffer_size = 2097144 query_cache_type = 1 query_cache_size = 312M log-slow-queries connect_timeout = 5 wait_timeout = 20 thread_cache_size = 15 read_buffer_size = 131072 table_cache = 64

    Read the article

  • Wake-on-lan only works so many times

    - by Chance
    I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

    Read the article

  • Netgear router keeps disconnecting iPhone

    - by DisgruntledGoat
    My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

    Read the article

  • How can I backup entire installations of a program, instead of just manually backing up individual f

    - by NoCatharsis
    It seems pretty straightforward to backup individual files, such as pictures, saved games, or settings files - just copy them straight over to your 2nd HDD or to an online service like DropBox. However, is there any way to backup entire installations of a program? For instance, my Firefox directory has a lot of personal customizations and add-ons. I don't want to go through each item and decide to back it up or let it go. So my next option is to copy out the entire directory for backup. But, if I copy the entire directory back onto the HD after a format, it is not an integrated installation and this seems like it could be troublesome. I would assume Windows cannot detect the directory for uninstallation, or would not let you choose Firefox as your default browser, right? I'm no pro, but this sounds like a bad idea. So my question is whether there is a good way to preserve all necessary files, while also preserving the full installation process of an application. This is not specific to Firefox - I would like to know how to do this for any application. Thank you.

    Read the article

  • I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

    - by ChrisF
    Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

    Read the article

  • Postgresql connection refused

    - by Jonathan
    I'm trying to remotely connect to my postgresql database. I have two virtual machines set up both running ubuntu 14.04. I am trying to connect to the second vm using the first vm using psql -h 10.0.1.23 -U postgres -d postgres But I receive the error: Could not connect to server: Connection refused Is the server running on host "10.0.1.23" and accepting TCP/IP connections on port 5432? I have changed the pg_hba.conf and added host all all 10.0.1.64/24 md5 host all all * md5 host all all 0.0.0.0/0 md5 And changed the postgresql.conf listen_address=" * " In an attempt to allow all incoming connections. I have also tried to change the firewall settings, but I am unsure of whether or not the ports are properly listening for the connection. Edit: Output of netstat -an | grep -E '^tcp[^6].*LISTEN' tcp 0 0 127.0.1.1:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN

    Read the article

< Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >