Search Results

Search found 14828 results on 594 pages for 'settings py'.

Page 498/594 | < Previous Page | 494 495 496 497 498 499 500 501 502 503 504 505  | Next Page >

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

  Read the article

• Forcing programs to be installed to another drive

  - by zyboxenterprises

  I have an SSD as my main Windows drive, with a 640GB 2.5" HDD, partitioned to store programs and user settings, and also to act as backup (it's the only thing I had lying around at the time of building my PC). The task was to make the PC as fast as possible, while having an increased storage capacity available to store normal user data, and to assist in my small data recovery business. The problem is that whenever I install a program, it installs to C:\Program Files [(x86 for the 32 bit programs]\, although I have changed the environment variables. This wouldn't normally be an issue, however every installation program points its shortcut to my 640GB HDD. The root layout of both drives: To clarify: Program files get installed to C:\ Program shortcuts are always pointed to Z:\, my 640GB HDD Modifying the relevant environment variables doesn't do anything, I looked at this, but however it only talks about modifying the registry and environment variables, which I have already done so. I install to the Z:\ drive if the installation program lets me change the installation path, but however the installation programs sometimes don't let me change this. Is there a way that I can force every program to install to the relevant location on Z:\? Perhaps I'm missing something here? Edit: Found this program; would it be appropriate to use in my case? I would be able to move the entire Program Files (and its x86 version) to Z:\, without impacting on the performance.

  Read the article

• Howto enable SMPTS (465) postfix CentOS

  - by user197284

  I need help is enabling SMTPS. I use postfix , dovecot with MySQL(virtual domains). I do not know how to enable SMTPS(465). I already added tls related settings and key and certificate in the "/etc/postfix/main.cf" OS: Centos 6.4 64 bit Please my /etc/postfix/master.cf file here # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd -o content_filter=smtp-amavis:127.0.0.1:10024 -o receive_override_options=no_address_mappings pickup fifo n - n 60 1 pickup -o content_filter= -o receive_override_options=no_header_body_checks cleanup unix n - n - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - n 300 1 oqmgr tlsmgr unix - - n 1000? 1 tlsmgr rewrite unix - - n - - trivial-rewrite bounce unix - - n - 0 bounce defer unix - - n - 0 bounce trace unix - - n - 0 bounce verify unix - - n - 1 verify flush unix n - n 1000? 0 flush proxymap unix - - n - - proxymap smtp unix - - n - - smtp # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - n - - smtp -o fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - n - - showq error unix - - n - - error discard unix - - n - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - n - - lmtp anvil unix - - n - 1 anvil scache unix - - n - 1 scache # # ==================================================================== # Interfaces to non-Postfix software. Be sure to examine the manual # pages of the non-Postfix software to find out what options it wants. # ==================================================================== maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/local/bin/maildrop -d ${recipient} uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=foo argv=/usr/local/sbin/bsmtp -f $sender $nexthop $recipient # # spam/virus section # smtp-amavis unix - - y - 2 smtp -o smtp_data_done_timeout=1200 -o disable_dns_lookups=yes -o smtp_send_xforward_command=yes 127.0.0.1:10025 inet n - y - - smtpd -o content_filter= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks=127.0.0.0/8 -o smtpd_error_sleep_time=0 -o smtpd_soft_error_limit=1001 -o smtpd_hard_error_limit=1000 -o receive_override_options=no_header_body_checks -o smtpd_bind_address=127.0.0.1 -o smtpd_helo_required=no -o smtpd_client_restrictions= -o smtpd_restriction_classes= -o disable_vrfy_command=no -o strict_rfc821_envelopes=yes # # Dovecot LDA dovecot unix - n n - - pipe flags=DRhu user=vmail:mail argv=/usr/libexec/dovecot/deliver -d ${recipient} # # Vacation mail vacation unix - n n - - pipe flags=Rq user=vacation argv=/var/spool/vacation/vacation.pl -f ${sender} -- ${recipient} retry unix - - n - - error proxywrite unix - - n - 1 proxymap Please help to enable SMTPS. I have amavis enabled

  Read the article

• Connect trough remote computer connection

  - by Didac

  First, sorry for my english and my poor knowlodge of this subject. I have a dedicated server placed in Germany (windows 2008 R2) and I live in spain. I would like to access internet from my home computer (Windows 7 Pro x64), trough my server in Germany, so I can use a German IP, what I need some times. I have complete acces in to both computers, but I just don't know where to start. (My knwoledge is limited to software development :/ ) I'd like to know where to start, if I need to create a VPN and so.. Thanks in advance! Update 1 I tried a lot of options of OpenVPN, but I sadly I know nothing abuot networking, so I have to accept I do not know what I'm doing :( Here are my config files (note most of the options are from the sample config files). server.conf #server config file start port 1194 proto udp dev tun server 10.0.0.0 255.255.255.224 #you may choose any subnet. 10.0.0.x is used for this example. ca "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\server.crt" key "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\server.key" dh "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\dh1024.pem" push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" #the following commands are optional keepalive 10 120 comp-lzo persist-key persist-tun verb 5 #config file ends client.conf #client config file start client dev tun proto udp remote 176.9.99.180 1194 resolv-retry infinite nobind persist-key persist-tun ca "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\client1.crt" key "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\client1.key" ns-cert-type server comp-lzo verb 5 explicit-exit-notify 2 ping 10 ping-restart 60 route-method exe route-delay 2 # end of client config file And here's the server's network settings: IP address: 176.9.99.180 Subnet mask: 255.255.255.224 Default gateway: 176.9.99.161 Preferred DNS server: 127.0.0.1

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Copy all installed programs & files in a hard disk (which has 32 bit Windows 7) and clone/transfer it to another computer which has 64 bit Windows 7

  - by galacticninja

  I recently got a new PC which has a 64-bit Windows 7 installed. The current PC that I am using has a 32-bit Windows 7 installed. I would like to know if there is a software that can copy all my installed programs and files in the hard disk with the 32-bit Windows 7 PC and transfer it to the newer PC's hard disk which has a 64 bit version of Windows 7. This is essentially like "cloning" a hard disk but I would like to use a 64-bit OS in the target drive, instead of also using the 32-bit OS of the source drive. I would like to do this I can avoid reinstalling and reconfiguring my installed programs and files again on the new PC. If possible, I would like the new PC to work as it was in my previous PC, with the installed programs, configuration and files intact except that the OS is now 64-bit and the hard disk has a larger capacity. I have heard of programs that can clone a hard disk, but my concern is that the 32-bit Windows 7 OS will also be cloned to the new 64-bit PC. If it is not possible to transfer my installed programs and settings like the way I described, are there software that can make it easier to migrate my installed programs, their configurations and my files from a 32-bit Windows 7 PC to a 64-bit Windows 7 PC? Details: I have a SATA to USB connector/adapter to copy files in the current hard disk to the newer one. The two PCs are connected through LAN, so I can also transfer files through LAN. Both PCs only have one hard disk.

  Read the article

• How do I configure VMware View location-based printing to use Active Directory Groups?

  - by Jason Pearce

  I am attempting to configure VMware View 4.5's Location-Based Printing, which leverages an included OEM version of ThinPrint, to assign printers to active directory groups. The location-based printing feature maps printers that are physically near client systems to VMware View desktops. I am using the Active Directory group policy setting AutoConnect Location-based Printing for VMware View, which is located in the Microsoft Group Policy Object Editor in the Software Settings folder under Computer Configuration. The AutoConnect Location-based Printing for VMware View appearst to be just a name translation table. It permits me to assign a specific printer or printers to an IP Range, Client Name, Mac Address, User, or User Group. I'm attempting to assign printers to active directory user groups. I have created a new active directory group for each printer that I intend to use in VMware View desktop pools. I will then assign active directory users to the active directory groups that represent each network printer. Example: doej is a member of the PTR-FLOOR2-NORTH-ROOM255 active directory group. Using AutoConnect, I assigned the group to receive a network printer by adding PTR-FLOOR2-NORTH-ROOM255 in the User/Group column. Problem: When doej logs in to his VDI session, the printer is not present. However, if I use a wildcard "*" in the User/Group column instead of the specific PTR-FLOOR2-NORTH-ROOM255 active directory group, the printer is present and functions as designed. Alternatives: I have tried assigning printers to active directory groups within AutoConnect in the following ways, all unsuccesfull: PTR-FLOOR2-NORTH-ROOM255 domainexample\PTR-FLOOR2-NORTH-ROOM255 domainexample.local\PTR-FLOOR2-NORTH-ROOM255 Confirmation: The information used to map the printer to the VMware View desktop is stored in a registry entry on the View desktop in HKEY_LOCAL_MACHINE\SOFTWARE\Policies\thinprint\tpautoconnect. For each of these examples, I have reviewed the registry entry and can confirm that the desktop is receiving the information from the AutoConnect translation table. Summary: Can anyone provide an example of how to configure VMware View 4.5's Location-Based Printing so that I may assign network printers to active directory groups via the included AutoConnect tool? I would welcome a clear example of a working configuration. Thank you.

  Read the article

• Scripted forwarding for Outlook 2003

  - by John Gardeniers

  We have a staff member in sales who has gone onto a 4 day week (getting ready for retirement), so each Thursday afternoon her email needs to be forwarded to another user and each Friday afternoon it needs to be set back. I'm using the VBS script below to do this, run via the Task Scheduler. Although the script appears to do it's job, based on what I see when I view the user's Exchange settings, Exchange doesn't always recognise that the setting has changed. e.g. Last Thursday the forwarding was a enabled and worked correctly. On Friday the script did it's thing to clear the forwarding but Exchange continued to forward messages all weekend. I found that I can force Exchange to honour the changed setting be merely opening and closing the user's properties in ADUC. Of course I don't want to have to do that. Is there a non-manual way I can have Exchange read and honour the setting? The script (VBS): ' Call this script with the following parameters: ' ' SrcUser - The logon ID of the suer who's account is to be modified ' DstUser - The logon account of the person to who mail is to be forwarded ' Use "reset" to clear the email forwarding SrcUser = WScript.Arguments.Item(0) DstUser = WScript.Arguments.Item(1) SourceUser = SearchDistinguishedName(SrcUser) 'The user login name Set objUser = GetObject("LDAP://" & SourceUser) If DstUser = "reset" then objUser.PutEx 1, "altRecipient", "" Else ForwardTo = SearchDistinguishedName(DstUser)' The contact common name objUser.Put "AltRecipient", ForwardTo End If objUser.SetInfo Public Function SearchDistinguishedName(ByVal vSAN) Dim oRootDSE, oConnection, oCommand, oRecordSet Set oRootDSE = GetObject("LDAP://rootDSE") Set oConnection = CreateObject("ADODB.Connection") oConnection.Open "Provider=ADsDSOObject;" Set oCommand = CreateObject("ADODB.Command") oCommand.ActiveConnection = oConnection oCommand.CommandText = "<LDAP://" & oRootDSE.get("defaultNamingContext") & ">;(&(objectCategory=User)(samAccountName=" & vSAN & "));distinguishedName;subtree" Set oRecordSet = oCommand.Execute On Error Resume Next SearchDistinguishedName = oRecordSet.Fields("DistinguishedName") On Error GoTo 0 oConnection.Close Set oRecordSet = Nothing Set oCommand = Nothing Set oConnection = Nothing Set oRootDSE = Nothing End Function

  Read the article

• Setup: Eclipse in Ubuntu with Apache2 and Subversion

  - by Ricalsin

  Trying to setup Eclispe. I am running ubuntu 10.10 (Maverick). Apache2.2.16 Subversion 1.6.12 The Eclipse help/about/installed software says: Eclipse Platform 3.5.2 Subclipse 1.0.0 Version Control with Subversion 1.1.1 The Subclips wiki I followed is here I have installed the libsvn-java app as discussed. I added the line "-Djava.library.path=/usr/lib/jni" to the eclipse.ini file I checked the Eclipse help/about/confirguration settings and both of these lines are listed: eclipse.vmargs=-Djava.library.path=/usr/lib/jni java.library.path=/usr/lib/jni I checked that those files are in those directories. Still, when I check the preferencesteamsvn an error dialog shows: Failed to load JavaHL Library. These are the errors that were encountered: no libsvnjavahl.1 in java.library.path Incompatible JavaHL library loaded 1.3.x or later required I followed the "Testing JavaHL libraries" troubleshooting section at the bottom of the wiki: I downloaded the tarbal and ran it in a folder on my desktop with no problems. Then, I followed the instructions and placed that file INSIDE the path (usr/lib/jni/testJavaHL) and ran it from there. There are 50 tests performed and each one of them came back with this same error (posting only one for brevity): 50) testCommitRevprops(org.tigris.subversion.javahl.BasicTests)java.io.FileNotFoundException: /usr/lib/jni/testJavaHL/local_tmp/greek_files/iota (No such file or directory) at java.io.FileOutputStream.open(Native Method) at java.io.FileOutputStream.<init>(FileOutputStream.java:209) at java.io.FileOutputStream.<init>(FileOutputStream.java:160) at org.tigris.subversion.javahl.WC.materialize(WC.java:70) at org.tigris.subversion.javahl.SVNTests.buildGreekFiles(SVNTests.java:303) at org.tigris.subversion.javahl.SVNTests.setUp(SVNTests.java:222) at org.tigris.subversion.javahl.RunTests.main(RunTests.java:111) FAILURES!!! Tests run: 50, Failures: 0, Errors: 50 Any ideas as to how/why the "local_tmp/greek_files/iota" is appended to the directory? I assume that's my problem.. I'm also having a problem with newrepository location = ...as the directory location of my svn repository is one level above the home directory - which is prepended to whatever I place in the dialog box - resulting in this error: svn: '/home/ricalsin/file:/home/svn' does not exist Thank you for any help.

  Read the article

• Apache2 doesn't serve PHP-scripts correctly

  - by cmbrnt

  I've run into a problem with my Apache 2.2.16 configuration, running on Debian Squeeze. The problem is that it stopped serving PHP5-scripts completely. When I try to access the sites with Google Chrome, it instead downloads a file called "download", which contains the contents of the script. This is of course not a good thing. It does serve common html-files perfectly... I've been at this for quite a while now, and after all the googling and troubleshooting, I thought it would be a good time to ask you guys. Here's what I've got: The php5 and libapache2-mod-php5 packages are installed /etc/apache2/mods-available contains both php5.load and php5.conf, and these are symlinked from the mods-enabled directory The /etc/php5/ directory is left untouched since the installation. Here's the contents of /etc/apache2/mods-available/php.load: LoadModule php5_module /usr/lib/apache2/modules/libphp5.so And /etc/apache2/mods-available/php.conf: <IfModule mod_php5.c> <FilesMatch "\.ph(p3?|tml)$"> SetHandler application/x-httpd-php </FilesMatch> <FilesMatch "\.phps$"> SetHandler application/x-httpd-php-source </FilesMatch> <IfModule mod_userdir.c> <Directory /home/*/public_html> php_admin_value engine Off </Directory> </IfModule> </IfModule> What am I missing? This is a server with modified virtual hosts and the like, so I might have changed some settings which causes this problem, but simply purging and reinstalling is not an option so far, since the configuration is quite extensive. Any help would be great. Thanks.

  Read the article

• Can't access Port 80 from external

  - by dewacorp.alliances

  Hi there I have configuration like this: NETGEAR MODEM LINKSYS ROUTER SERVERS In the modem, I've setup as bridging and all the traffic is controlling by this ROUTER. Prior to this setup, I can access website from external (port 80) plus exchange servers (mail) and https. But now with this configuration, I can only send/receive using Exhcange servers and access OWA (Outlook web access using port 443) .... and no internal websites from outside. This is my config for LINKSYS ROUTER Application | Start | End | Protocol | IP Address Ms Exchange | 25 | 25 | Both (TCP/UDP) | 192.168.100.8 Internets | 80 | 80 | Both (TCP/UDP) | 192.168.100.11 SSL | 443 | 443 | Both (TCP/UDP) | 192.168.100.8 Exchange | 110 | 110 | Both (TCP/UDP) | 192.168.100.8 192.168.100.11 is a UBUNTU web server that running the apache which controlling the virtual name (extranet, cms, test) to redirect to the different servers. As you can see, the home internet is only allowing public IP address. Now I test this schenarion in internal network work nicely. For instance. If I type in extranet.XXX.local it goes to the right applicatios or if I try CMS.XXX.local again it goes to the right one. I also asked to ISP just in case if they are blocking the inbound port 80 for unknown reason. They said no. So I didn't understand why this happens. I suspect the configuration that I have between MODEM ROUTER but I counldn't work what it is. I don't have a documentation of previous settings and I don't know if there is a port that I need to open as well. I am appreciated your comment

  Read the article

• Printer spooler service stop running when sent print job

  - by Hanan N.

  Every time i am sending a print job to the printer, i am don't get any response from the printer, and at the printer job list at the status of the job, i see that there was an Error, but it don't give me any clue on what could be the problem. After some investigation i found that every time that i send the print job to the printer the printer spooler service stops to run, then after a second or two it start again (i think that this behavior is related to the printer spooler settings to rerun it self after it stops). Things that i have tried so far: Remove and Install again the Driver. After removing the driver, i have removed the unnecessary registry keys according to this article from Microsoft, these are: Rename all files and folders in: c:\windows\system32\spool\drivers\w32x86 Remove anything but Drivers Print and Processors: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environment\Windows NT x86 Remove anything in here: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors but: BJ Language Monitor Local Port Microsoft Document Imaging Writer Monitor Microsoft Shared Fax Monitor Standard TCP/IP Port USB Monitor WSD Port Disconnect and Reconnect the Printer. Clean the computer from Viruses & Spywares. Currently i am stuck, i have no more things to try, if anybody know about any kind of solution please let me know about it. Since i am want to keep this post as general problem that relate to the printer spooler, and not just my particular problem, i didn't included inside the windows version & the printer model, they are (although i think that it isn't relate just for that particular model): Windows 7 32bit, HP Officejet 4500 G510g-m (connect to the computer via USB). Thanks.

  Read the article

• How to scan multiple pages from a book under Linux?

  - by rumtscho

  I want the process to look like: I choose the correct scan settings (dpi, color depth, etc) I lay the first page on the scanner and trigger the process The scanner scans the page and waits for me to position the next page correctly I confirm that the next page is ready for scanning Repeat the above two steps until I tell the scanner that there are no more pages to come The scanner saves everything into a single PDF. I tried both xsane and gscan2pdf. First problem: they want me to know how many pages will be scanned. This is already a nuisance, but I can do the counting if needed. The main problem is that in step 3, the scanner does not pause. It is probably optimised for being fed loose sheets. The next scan process is triggered automatically as soon as the CCD has returned to the start position. The time the scanner needs to return the CCD is very short and I can't turn the page and position the book properly. Is there a software which can do the scan process in the way I described above, or did I just miss a setting available in xsane or gscan2pdf to make the scanner pause? If it makes any difference, the scanner is an Epson Stylus SX620FW, I run it using the manufacturer-provided driver.

  Read the article

• Converting PDF eBooks into a Kindle format

  - by Ender

  Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this? EDIT: I've tried Calibre, and have checked their forums to play with some of the advanced settings, yet the solutions available seem to be extremely poor, especially if the book you're attempting to read contains equations, code, or anything outside of plain text. I've also tried Amazon's conversion service, which wasn't much help with such documents. The best way I have found so far is to build the entire thing over again in ePub or RTF format and convert to MOBI from there. This works for text-heavy books with tables, but anything technical still isn't covered. Can anyone help with this?

  Read the article

• Port Forwarding to put my web server on The Internet

  - by Chadworthington

  I went to http://canyouseeme.org/ to check to see what my external IP address. Regardless of what port I enter, it tells me that the port is blocked. I have a LinkSys router that basically has the default settings with the exception that I have WEP encrptin setup and I have forwarded a few ports, including 80 and 69. I forwarded them to the 192.x.x.103 IP address of the PC which is running IIS. That PC runs Symantec Endpoint Protection, which I right mouse clicked in the tray to Disable. These steps used to make my PC visible so I could host my own web site in IIS on port 80, or some other port, like 69. Yet, the Open Port tool cannot see my IP when it checks eiether port and when I navigate to http://my external ip/ I get "page cant be displayed" At first I was thinking that maybe Comcast is blocking port 80, but 69 doesnt work eiether. I do not see any other blockking set up in my router and, as I mentioned, I went with teh defaults except where discussed. This is a corporate PC and Symantec End Point Protecion is new to it (this previously worked on teh same PC with Symantec Protection Agent), but I thought that disabling Sym End Pt from the tray, that that would effectively neutralize it. I do not have the rights to kill the program itself. Any suggestions on what else to try to make my PC externally visible?

  Read the article

• Configuring a MySQL 5.1 Instance on Windows 7 Professional x64 Fails

  - by Thomas Owens

  I'm trying to set up my laptops to function as mobile development environments. Installing the software on my Linux machine and getting it configured was fairly straightforward, however I'm having trouble getting MySQL 5.1 Server installed and configured on Windows 7 Professional 64-bit. I'm currently using the Windows MSI Installer for the complete MySQL 5.1 system (as opposed to the Essentials installer also available). I've tried to install using both the 32-bit and 64-bit versions of MySQL 5.1 - the same events occur in both. I've installed both the Server Instance Configuration Wizard and Workbench and everything appears to be installed just fine. When I open the Instance Configuration Wizard, I select Detailed Configuration. On the next screen, I select Development Environment, then Multifunctional Database on the next screen. I leave the InnoDB settings unchanged. I select Manual Setting with 5 concurrent connections. I enable TCP/IP Networking on Port 3306 and Enable Strict Mode. I select the Standard Character Set. I check the boxes for Install as a Windows Service (and provide the name "MySQL") and Include the Bin Directory in Windows PATH. On the next screen, I set my root user name and password. I do not enable root access from remote machines and I also do not create an anonymous account. On the final screen of the wizard, when I click "Execute", the first two tasks (Prepare Configuration and Write Configuration File) complete. However, when it reaches Start Service, the wizard hangs and becomes unresponsive ("Not Responding" appears in the title bar and Task Manager). I would really like to be able to use both my Windows and Linux laptops as full-blown mobile development environments, but I can't do that without being able to run MySQL. Has anyone encountered this problem before? What options do I have to correct it?

  Read the article

• What is the main reason of adsl modem/routers dying ?

  - by ldigas

  The other day my home adsl modem/router (dwg 684t in this case) died. A guy from the telecom company came, brought another so no problem in day to day operation, but he also left this one. Now, I'm interested ... it didn't fall, it wasn't electrocuted ... but it just doesn't work. What could be the problem ? Can they be fixed ? Is it worth it (in which case I would have two which is always nice) ... What are the usual problems that occur with them ? In this case, I can connect to the router, I can see its settings, I just can't connect to the internet. With the new one everything works. Weird. Edit: Additional question: Can those things be fixed ? I mean, is it worth giving it to a local tinker for him to experiment on it ? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm gonna archive it in the "cylinder register")

  Read the article

• Switching from Onboard intel to Nvidia Dedicated GPU

  - by Anarkie

  How can I switch from Intel onboard grpahics to Nvidia Dedicated GPU? When I go to windows screen resolution I see intel. I cant change it. I go to Device Manager, I see both Adapters are there and Nvidia is known.I disabled intel, I didnt see any option to set one as primary so I disabled intel, black screen!Reboot and re-enable intel. I right click on the desktop, choose "Nvidia Control Panel" and on 3D options I chose the desired game I want to play, High performance Nvidia, but it didnt switch when I started the game. Then I made preferred GPU in the global settings High performance Nvidia for everything it still didnt change.I understand to save the battery etc. there is a switch option between these two but I dont see this switch when it is necessary, I cant also switch manually?Is there a manual switch FN key?I looked but couldnt find. Why I want to do this? 1) Better game peformance. 2) I want to play an old game from 2002(Diablo 2 LOD), when I start the game there are black bars on the sides, so screen becomes just smaller which I dislike!I heard this is intel's specification to center the display.But instead I would like to scale or expand it to fit widescreen(fullscreen).Which should be possible with Nvidia. My Notebook Specs: Fujitsu Lifebook AH531, Win7 , 64 bit, i5, intel HD graphics onboard, Nvidia GT 525. I didnt install Nvidia later, it was always installed and ready from the moment I turned on the computer first time. How I determined that the cards werent switched when I am playing the game: with the windows key I exited from the game, then looked at screen resolutions menu, still saw intel, also the game was still with black bars.I know intel GPU should enough for Diablo 2 but I am interested in this answer for further games, I dont always play Diablo, what if I install an up to date game for example?Then Intel will not be sufficient.I would like to learn the switch option.

  Read the article

• ubuntu 9.10 installer doesn't recognize the hard drive

  - by dan

  I downloaded Ubuntu 9.10 x86_64 and am trying to install it on a fairly modern system with a Gigabyte GA-MA770-UD3 motherboard. Ubuntu 9.04 installed fine and still will when I stick that disc in, but 9.10 doesn't see my hard drive (western digital 250GB). If I boot from the disc, I can install gparted and it does recognize the drive, but when I try to start the install process from the live disc, Ubuntu again doesn't recognize the hard drive. I checked /var/log/messages and see this: Nov 12 17:28:08 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was bad, boot with 'nodmraid'. Nov 12 17:28:08 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: no raid sets and with names: "nvidia_ciiajheb-0" Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. I checked my BIOS, SATA is enabled and is set to IDE mode, so there shouldn't be software RAID, but nonetheless, I added nodmraid to the boot line and tried again. It still doesn't recognize the drive. I checked /var/log/messages again and now see this: Nov 12 17:49:38 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was boad, boot with 'nodmraid'. Nov 12 17:49:38 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Any ideas on things to try? I've tried all of the various BIOS settings for SATA. IDE,RAID, etc. Nothing seems to work.

  Read the article

• Ubuntu 10.10 forgets desktop theme.

  - by Marcelo Cantos

  I am running Ubuntu in VirtualBox (on a Windows 7 host). Several times now, the top-level menu bar, the task bar — and seemingly every system dialog — have forgotten the out-of-the-box "Ambiance" theme they conform to when I first installed the system. Window captions still preserve the theme, but pretty much nothing else does. I have searched high and low on Google for assistance with this problem. Everything I've found suggests either running some gconf reset or deleting .gconf* .gnome* and other similar directories. I have followed all this advice and nothing works. I still get a boring Windows-95-style gray 3D look and feel. On previous occasions, after much messing around I've given up and rebooted the VM instance, and been pleasantly suprised to see the original "Ambience" theme restored throughout the UI, but invariably it disappears again some time later, usually after a reboot, so I can never figure out what I did that broke it. Here's a sample from Ubuntu's site of what I want it to look like. And here's a screenshot of my system as it currently looks. Also note that my GNOME Terminals normally have a nice purple semi-translucent look, and as can be seen from the screenshot, they are now just a solid matt white. This last time (just this morning), trying numerous combinations all the usual tricks and rebooting several times hasn't fixed it, so here I am on SU wondering: How do I recover the out-of-the-box theme for my Gnome/Ubuntu desktop, noting that blowing away all config files — as suggested in many places online — fails to achieve this? EDIT: It might help to know that it seems to fail either after I resize the VM instance, forcing the Ubuntu desktop to resize itself, or after I play around with Compiz settings. I haven't been able to figure out which of these it is, and it could be neither. Given the amount of pain I have had to go through to get things back to normal (and given that I am at a loss as to how to do so), it has proven difficult to definitively isolate the cause.

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Links break in IE9 when using Wordpress plugins in non Wordpress Page

  - by mouli

  I have a site that uses SEF URLs and htaccess RewriteRules to serve up the pages. This has worked fine for several years until the arrival of IE9. Now it appears that the links are not being rewritten and the site is dead in the water. I have tried different compatabilty modes, to no avail, and I've played with the Rewrite Rules over and over, tried different doctypes and a few other browser settings. I agree that it cannot in theory be a browser specific problem if the problem is with the htaccess file but this site works in IE8, firefox and chrome. I have run the rewriterule through a validator and it looks fine. Any ideas would be appreciated as I am running out of ideas. The site is www.marlboroughsounds.co.nz a sample link is http://www.marlboroughsounds.co.nz/walking/freedom-walk-queen-charlotte-track/4dfw and the rewrite rule thats not working looks like this: RewriteRule ^walking/.*/([a-z0-9_]*)/?$ /walking.php?act_code=$1 [L] The link fails and it serves up a browser 404 page, not even the custom 404 I have for the site. Any ideas would be much appreciated as I am stumped.

  Read the article

• Windows 7 Install: No drives were found

  - by Albert Bori

  I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

  Read the article

• Fedora installed in Legacy mode, how to make it work in UEFI?

  - by TryntaLearn

  I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

  Read the article

• High fan speed with no reason

  - by Klaus

  For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

  Read the article

< Previous Page | 494 495 496 497 498 499 500 501 502 503 504 505  | Next Page >