Search Results

Search found 14924 results on 597 pages for 'kernel mode'.

Page 498/597 | < Previous Page | 494 495 496 497 498 499 500 501 502 503 504 505  | Next Page >

• xrandr fails when 3rd monitor has higher resolution

  - by Pi3cH

  I tried many combinations with xrandr command under lubuntu 12.04 to setup my three monitors DVI (DELL 1) left detected as HDMI1 HDMI (LG E2290) middle detected as HDMI2 VGA (DELL 2) right detected as VGA1 I can get the display with fix 1280x1024 on all the monitors. But once I setup 1280x1024 + 1920x1080 + 1280x1024, I get blank screen on all the monitors. Sometimes it throws crts fail error instead of blanking out. Anyone have similar issues? any solutions/workarounds? P.S. I can setup two monitors using 1280x1280 and 1920x1080 P.S.S. HDMI2 required at least 1920x1080 to display sharp picture. Outputs (it seems graphic card supports up to 8192x8192): xrandr Screen 0: minimum 320 x 200, current 3840 x 1024, maximum 8192 x 8192 VGA1 connected 1280x1024+2560+0 (normal left inverted right x axis y axis) 338mm x 270mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI1 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI2 connected 1280x1024+1280+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0 + 1680x1050 60.0 1280x1024 75.0 60.0* 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) 3 CRTs (0,1 VGA, 0,1,2 for other HDMI) xrandr --verbose VGA1 connected 1280x1024+2560+0 (0x47) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x42 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 0 1 ... HDMI1 connected 1280x1024+0+0 (0x47) normal (normal left inverted right x axis y axis) 376mm x 301mm Identifier: 0x43 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 0 1 2 ... HDMI2 connected 1280x1024+1280+0 (0x47) normal (normal left inverted right x axis y axis) 477mm x 268mm Identifier: 0x44 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 2 CRTCs: 0 1 2 Below command fails: xrandr --output VGA1 --auto --output HDMI2 --auto --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Below command passes: xrandr --output VGA1 --auto --output HDMI2 --mode 1280x1024 --rate 60.0 --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Graphic card VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09)

  Read the article

• My SSD stopped working as it ends up in blue death right after windows 7 launches, how can I reset it for new windows install?

  - by HattoriHanzo

  As I mentioned in the title my SSD suddenly started to fail as after launching Windows 7 it goes straight to completely idle and after a few minutes it goes to blue death and restarts. I have an another HD with a windows xp on it and it works fine and I can also see the SSD and can access everything on it. Windows 7 on the SSD does work in safe mode though yet I didn't manage to find out what causes the problem. Since I can sill access the files and save them to another HD I'm looking for the best way to wipe and reinstall Windows 7. I have yet failed to find an easy to follow (or even understand) guide, different sources on the internet recommend different ways of doing this. And some guides are just simply full of terms I have no clue about. It's an OCZ Vertex 2 120GB. I"d very much appreciate if someone could give me an advice on what I should do, preferably in a way so I could regain the best possible performance as well. it doesn't matter if I don't understand the science behind it as long as I can follow the steps. Thanks!

  Read the article

• Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

  - by paul

  I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

  Read the article

• Windows 7 Taskbar resets on every login

  - by Arne Mertz

  I like to reorder my Taskbar a bit, other than the Windows 7 default is. I use two "rows", the lower is for quicklaunch and other toolbars: This works perfectly, as long as I don't log off from the computer. Every time I log in, Windows 7 has messed up/reset the toolbar positions like this: So I have to drag them into position again and again, every morning. Fixing the taskbar positions won't help, I tried to google for the problem but it does not seem to be very common. Does anyone recognize that problem and has a solution? Update: This is not the AutoLogon bug. AutoLogon is off. We have installed Novell at our company, and it does not matter wether I log directly onto the Novell network or only to the computer first and to Novell later. Update2: I get the same issue when I logon without Novell, i.e. when I log on only to the computer. When I boot in safe mode, the taskbar looks essentially the same: Update3: KB979155 says it's "not applicable to my system". Creating a neew user is not an option since I don't have the admin privileges to do that - I have almost any other local admin privileges, though.

  Read the article

• STOP 0x7b booting from iSCSI

  - by Michael

  Hi, I've a Windows 2008 SBS running. It boots of iSCSI. That setup worked for months until yesterday. I intended to reboot and gained a: STOP 0x0000007b INACCESSIBLE_BOOT_DEVICE and no idea why. My setup hasn't changed. No new controller, no new or changed iSCSI targets, no new Network Card or IP address changes. I had all Windows Updates on it. Last known good: same STOP. Allow unsigned drivers: same STOP. Safe mode (all variants): same STOP. Mount target from a client: works. Filesystem check fine. I booted of the SBS DVD but in computer repair options my target doesn't appear. When i choose setup the target appears. So, how can i diagnose what's going wrong? Any helpful tools? Any hints? Thanks in advance Michael

  Read the article

• How to improve Samba performance on VirtualBox machine?

  - by ColinM

  I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

  Read the article

• Javascript loading never completes on many sites

  - by Joe

  I recently moved country and have found that on many websites the page never finishes loading. In some cases, no content is ever displayed, but the loading will never time out. Loading Developer Tools in Chrome shows me that it is the Javascript files which never load. For example, this BBC article will never load compatability.js, though will load all the other JS files perfectly. Google Maps often fails to finish loading, meaning it's impossible to make searches. There seems to be no pattern to which files will fail to load (i.e. they don't come from the same CDN). I have tried Chrome, Safari and Firefox on OSX 10.8, and Chrome on my girlfriend's OSX 10.7. I have similar issues on the iPad. In many cases, if I can go to the mobile version of the page that seems to load fine. I have run the browsers in private mode, disabled plugins, updated flash, cleared the cache, flushed the DNS cache - though it would seem that if this is happening on other devices, none of this would work anyway. Is this an ISP issue? And if so, why would it be limited to certain JS files and not all? JS files from the same domain work fine, so I'm not really sure what I should be looking for.

  Read the article

• Clicking far away in vim in tmux in urxvt

  - by paps

  I use vim inside tmux inside urxvt, and the mouse works perfectly well for clicking and selecting text, except when I want to click too far to the right. It seems to be related to the distance in number of columns from the left. When I go beyond column ~200 (not sure about the exact number), clicking simply does nothing. Note that it's not related to a vim window: with two vim windows taking ~150 columns each, clicking will not work after the ~50th column in the second window. It's related to the whole vim session. Also note that clicking far away in a big tmux pane (200 columns) works perfectly. In my .tmux.conf I have this line: set -g default-terminal "screen-256color" and in my .vimrc I have this: if &term =~ "^screen" autocmd VimEnter * silent !echo -ne "\033Ptmux;\033\033]12;7\007\033\\" let &t_SI = "\<Esc>Ptmux;\<Esc>\<Esc>]12;5\x7\<Esc>\\" let &t_EI = "\<Esc>Ptmux;\<Esc>\<Esc>]12;7\x7\<Esc>\\" autocmd VimLeave * silent !echo -ne "\033Ptmux;\033\033]12;14\007\033\\" end It changes the cursor's color depending on the editing mode of vim, and it works, meaning that tmux really sets $TERM to "screen-256color" — but I don't know if this has any relevance with my mouse problem. I'm running Ubuntu 12.04, vim 7.3, tmux 1.6 and rxvt-unicode 9.14. Does anybody have an idea about what is causing this problem? Thanks.

  Read the article

• How to configure a Web.Config file to allow custom 404 handling while still displaying on-page 500 error detail?

  - by Mark

  To customize 404 handling and based on the hosting company's suggestion, we are currently using the following web.config setup. However, we quickly realized that with this configuration, any page error (500 error) are also getting redirected to this custom error page. How can I modify this config file so we can continue to handle 404 with custom file while still able to view on-page error? <?xml version="1.0" encoding="utf-8" ?> <configuration> <system.webServer> <httpErrors errorMode="DetailedLocalOnly" defaultPath="/Custom404.html" defaultResponseMode="ExecuteURL"> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="/Custom404.html" responseMode="ExecuteURL" /> </httpErrors> </system.webServer> <system.web> <customErrors mode="On"> <error statusCode="404" redirect="/Custom404.html" /> </customErrors> </system.web> </configuration>

  Read the article

• Routing and authenticating all access through squid

  - by Knight Samar

  Hi, I want to route all Internet access in my network through a Squid proxy server and authenticate and log all users. I want this to be a client-independent setting so that no one needs to do anything on their browsers or machines. I have set my network gateway as the proxy server so that all traffic will be sent to it. I have done this using options in DHCP server. Now I tried using squid as a transparent proxy, but then it won't authenticate in that mode. I tried using iptables to route all traffic to port 3128 but it won't popup the authentication dialog box from SQUID. I tried telling DHCP to give WPAD to all clients by placing a WPAD file on a webserver containing the following for automatic proxy configuration on clients: Changes in dhcpd.conf option wpad code 252 =test; option wpad "\n\000"; option wpad "http://192.168.1.5/wpad.dat\n"; The WPAD file: function FindProxyForURL(url,host) { return "PROXY squid-server-ip-address:3128 ; DIRECT "; } But the browsers (different versions of Firefox and IE) seem to ignore it. :( What should I do ?

  Read the article

• Doesn't VirtualBox 4.0 support drag-drop file copy yet?

  - by Benjamin

  Version 4.0.0 will be new major release. The following major new features were added: -New settings/disk file layout for VM portability; see the manual for more information. -Open Virtualization Format Archive (OVA) support; see the manual for more information. -VMM: support more than 1.5/2 GB guest RAM on 32-bit hosts -Language bindings: uniform Java bindings for both local (COM/XPCOM) and remote (SOAP) -invocation APIs -Chipset: added support for the Intel ICH9 chipset with 3 PCI buses, PCI express and -Message Signaled Interrupts (MSI) -Audio: Intel HD Audio is now available as guest hardware, for better support with modern -guest operating systems (e.g. 64-bit Windows; bug #2785). -GUI: redesigned user interface with guest window preview -GUI: new display mode with downscaled guest display -Resource control: added support for limiting a VM's CPU time and IO bandwidth. -Storage: support asynchronous I/O for iSCSI, VMDK, VHD and Parallels images -Storage: support for resizing VDI and VHD images -Windows Additions: support for automatically updating the Guest Additions (requires -installed Windows Guest Additions 4.0 or later) -Guest Additions: support for copying files into the guest file system What does the last line mean? I thought this is a drag-drop file copy feature like VMWare. I tried that. But I couldn't copy by drag-drop, ctrl-c ctrl-v either. Edit: I mean VBox 4.0 beta, not 3.x The release note is here. Download link is here.

  Read the article

• Apache memory allocation error message

  - by la_f0ka

  I'm trying to set up a medium sized Drupal 7 website on my miniserver but I keep getting a 500 error message. This is what I found in Apache's error log: [Wed Sep 12 15:02:04 2012] [notice] SSL FIPS mode disabled [Wed Sep 12 15:02:04 2012] [warn] No JkShmFile defined in httpd.conf. Using default /usr/local/apache/logs/jk-runtime-status [Wed Sep 12 15:02:04 2012] [notice] Apache/2.2.22 (Unix) mod_ssl/2.2.22 OpenSSL/1.0.0-fips mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 mod_jk/1.2.35 configured -- resuming normal operations [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] /usr/bin/php: error while loading shared libraries: libkrb5support.so.0: failed to map segment from shared object: Cannot allocate memory [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] Premature end of script headers: index.php [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] /usr/bin/php: error while loading shared libraries: libkrb5support.so.0: failed to map segment from shared object: Cannot allocate memory [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] Premature end of script headers: index.php [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] File does not exist: /home/brighton/public_html/favicon.ico [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] /usr/bin/php: error while loading shared libraries: libkrb5support.so.0: failed to map segment from shared object: Cannot allocate memory [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] Premature end of script headers: index.php I contacted support and they just told me I should just upgrade my package (right not I have a 512Mb account), but I am not sure if I'm buying it... even if I'm trying to access a file which only contains phpinfo(); I still get the 500. Any help would be much appreciated, and if there's need of any other information please let me know and I'll update the question. I compiled apache with tomcat because I intend to use Solr... not sure if this is relevant or not.

  Read the article

• Problem running “Central Administration” website after windows update at Windows 2003 Server Standar

  - by Magdy Roshdy

  I was have WSS 2.0 and then I upgraded to WSS 3.0 and the old instalation database was SQL 2000, now I have another SQL Server instance called:server_name\MICROSOFT##SSEE . After upgrade every thing works fine and our team started to use the portal and we sent lot of documents and make lot of activities on it. The problem started after installing Windows updates the website suddenly stopped and giving me an error "Cannot connect to the configuration database" If I tried to open SharePoint Products and Technologies Configuration Wizard it is gives me a strange error says: "An exception of type Microsoft.SharePoint.PostSetupConfiguration.PostSetupConfigurationTaskException was thrown. Additional exception information: SharePoint Products and Technologies cannot be configured. The current installation mode does not support SKU to SKU upgrades because there exists an older version of Windows SharePoint Services that must be upgraded first " At this post:http://stackoverflow.com/questions/114398/iis-error-cannot-connect-to-the-configuration-database/249494#249494 the guy of the second answer have the same problem and he suggested a solution but I don't understand well. I tried as he suggested to make the identity of the app pool of the SharePoint web site as "IWAM_server_name " after that the error changed as he said and I web site give me "Server Application Unavailable " and when checked the Event Viewer at the server I found that ASP.NET 2.0 give this exception: "Could not load file or assembly 'System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' or one of its dependencies. Access is denied ." and I don't know how to solve this problem. I'm really want to make my web site working because our team really need these documents and its stuff. I hope I will find some one to help me.

  Read the article

• Computer loop restarts on Windows loading

  - by Robinson G.

  My computer restarts, just after or during Windows loading (4 squares getting together), or after some time on the desktop IF I'm idle. In order to start the computer I either have to swap my RAM (24Go) in differents DIMM slots, for example (I have 4 slots) : 1-2-4 or 2-3-4 or 1-3-4, not the same position each boot or it restarts in a loop... I can also change the ram timing from 1.5 to 1.6V and it starts, at the next reboot I have to change it again to 1.5 or it won't boot... And If after all, I succeed to boot, I have to use the computer for about 10 minutes, and it's ok, if I don't, it restarts by itself after some minutes. If I stay on the BIOS, It's all OK, I can stay for a whole year without restarting. I have check my RAM on Memtest (4*8G SDRAM DDR3) : OK I have check without graphic card : Still the same. I tried to reset the bios stack by getting it off and on : Still the same. I tried to reset my BIOS, and many settings about the RAM in the menu : Still the same. CPU temps are just fine (around 35°C) I was thinking ofc about the motherboard but I want to be sure. Motherboard : MSI zh77a-g43 RAM : 4*8G Dual Mode or not (depends on the number I put ofc.) PSU : 600W (enough to run all the config) CPU : i7 3770 non K

  Read the article

• exim4 seem to stop listening

  - by trakos

  Hey, I have a strange problem with my exim4 configuration. I have a dedicated server running debian for quite a long time now, but I'm not really using it actively recently, so everything just worked due to lack of changes ;) However, recently, my exim4 smtp stopped answering on port 25. It does not respond through localhost, as well - even though it's set to listen on any interface available. Some things I've checked: ks:/home/trakos/Maildir/new# netstat -ap | grep exim tcp 0 0 *:smtp : LISTEN 12521/exim4 ks:/home/trakos/Maildir/new# exiwhat 12521 daemon: -q30s, listening for SMTP on port 25 (IPv4) ks:/home/trakos/Maildir/new# cat /var/log/exim4/rejectlog ks:/home/trakos/Maildir/new# cat /var/log/exim4/paniclog The queue is set for 30s only because I was running it in a non-daemon mode to see any output. Strangely enough, no suspicious output is given, netstat even shows it is listening on port 25, but still trying to telnet to it times out. The only things that may have changed recently are: I've got second IP for my server I remember that few days ago my spamassasin crashed, and I've started it up again So yeah, I'm really clueless about this one now :P I mean, I don't even know what could be failing here. Could someone give me some ideas what should I check next? PS: it has uptime of 442 days, so I haven't really tried rebooting it yet ^^

  Read the article

• How can I create a simple Exchange 2010 backup solution?

  - by bduncanj

  I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

  Read the article

• Outlook 2010 Crashing Unpredictably

  - by cbkadel

  Very often when I open up Outlook 2010 and start doing actions in it, it will hang and become non responsive. I have tried letting it finish, but it never does come back (up to 20 minutes of letting it try). I generally have to restart Outlook and try again. Usually after about an hour of doing this, Outlook somehow snaps out of it and works for the rest of the day. It's generally in the morning (though I doubt that's the key variable). Generally, the emails that cause problems are HTML/formatted, but not always. What I've done so far to troubleshoot: Install Latest Outlook Hotfix (I think Dec 14, 2010) Start Outlook in Safe Mode Neither of those steps seem to make a difference. Usually - after about 10-15 restarts of Outlook on any given day, then it starts working thereafter. My next step is to uninstall/reinstall Office 2010, but I'm hoping someone has seen this and knows what to do about it - though not sure. My configuration is like this: Microsoft Online Services (using Microsoft's Sign In App) - Connecting to Exchange I have two other Exchange accounts in this profile (new feature in 2010) connected through Outlook Anywhere. Life Meeting Conferencing Add In I've disabled the People tab/add in. I've disabled the "Send to Bluetooth" add-in. Not sure what else to do. Thanks in advance.

  Read the article

• Get Matrox Millenium video card working in Ubuntu 9.10

  - by wcoenen

  I have installed Ubuntu 9.10 on an old PC and it is mostly working, except for some heavy drawing defects that show up whenever I start dragging a window or scrolling inside a window or menu. It looks like the video driver copies the rectangle being moved to the wrong location. I have taken a look in /var/log/Xorg.0.log and the following line shows the detected video card: (--) PCI:*(0:0:8:0) 102b:0519:0000:0000 Matrox Graphics, Inc. MGA 2064W [Millennium] rev 1, Mem@ 0xf9800000/16384, 0xfb000000/8388608, BIOS @0x????????/65536 (==) Using default built-in configuration (30 lines) (==) --- Start of built-in configuration --- Section "Device" Identifier "Builtin Default mga Device 0" Driver "mga" EndSection How do I fix the drawing defects? It turned out that the 24 bit color depth (automatically selected by ubuntu 9.10) was the problem; apparantly the mga driver doesn't handle this well for cards with little memory. I took the following steps to resolve the issue (you can skip the first three steps if you already have a semi-working xorg.conf file): Reboot ubuntu in recovery mode, to get a root console without X running. Run Xorg -configure to generate a xorg.conf.new file Copy the file to /etc/X11/xorg.conf with cp xorg.conf.new /etc/X11/xorg.conf (assuming it didn't exist yet; that's why I generated it) Open the new config file with sudo nano /etc/X11/xorg.conf and make sure the screen section is configured for 16 bit color depth like this: Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection EndSection I can't guarantee those were the only important changes I made - I tried a few things in my attempts to create a valid xorg.conf file. But I'm pretty sure that the screen section was the important part.

  Read the article

• Assigning cores to VM in vSphere

  - by user114933

  Complete vSphere newbie here... Background: So, I have a 12 core machine with 24 VMs on it. Currently, all the processing power is shared between these VMs equally. The question: Can I configure one VM to be given two CPU's worth processing no matter what's happening on the other machines? My Research: I tried two things in vSphere... I set the reservation and limit on one VM to equal the same as two cores. To test if my objective was being reached, I measured the time it would take to gzip a file when other VMs were running nothing and when other VMs were running CPU intensive operations. I expected the time to gzip the file would be the same because this VM gets priority for some processing. Unfortunately, the time taken to gzip the file when other VMs were running something was significantly more than when other VMs were not running anything. I tried setting the Hyperthreaded Core Sharing mode to Internal hoping that this would mean that my VM would get at least an entire core to itself. This did not work either. Thanks in advance!

  Read the article

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Z.

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• Getting dwl-g122 to work on ubuntu

  - by User1

  I have a USB WiFi adapter, D-Link dwl-g122. I'm running Ubuntu 10.4. My laptop has a built-in wireless card that is connecting fine to the router. I plug in the usb and it never really connects. Here are some details: iwconfig wlan1 IEEE 802.11bg ESSID:"\x0B\xE1..." Mode:Managed Frequency:2.457 GHz Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lshw -c network: *-network:1 description: Wireless interface physical id: 3 logical name: wlan1 serial: 00:13:46:8b:xx:xx capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg dmesg [ 1096.814176] wlan1: direct probe to AP xxx (try 1) [ 1096.820960] wlan1: direct probe responded [ 1096.820969] wlan1: authenticate with AP xxx (try 1) [ 1096.823790] wlan1: authenticated [ 1096.823869] wlan1: associate with AP xxx (try 1) [ 1096.827667] wlan1: RX AssocResp from xxx (capab=0x411 status=0 aid=1) [ 1096.827674] wlan1: associated [ 1142.590912] wlan1: deauthenticating from xxx by local choice (reason=3) lsmod|rt2 rt2500usb 19643 0 rt2x00usb 11260 1 rt2500usb rt2x00lib 32133 2 rt2500usb,rt2x00usb mac80211 238896 3 ath5k,rt2x00usb,rt2x00lib cfg80211 148725 4 ath5k,ath,rt2x00lib,mac80211 led_class 3764 3 ath5k,rt2x00lib,sdhci It looks like the driver loads but it doesn't feel like connecting. The behavior is identical even if I blacklist the other wifi card (using an ath5k driver). It's almost like it is using the wrong password or something. Does anyone know what is happening? Is anyone using Ubuntu successful?

  Read the article

• Euro character messed up during FTP transfer

  - by djechelon

  My customer is using a very outdated ecommerce management system on my hosting service. For that product, no support is being provided anymore by the vendor. Brief explanation: the shop website, that claims to run under LAMP stack, is built by an old Visual Basic Windows application running on MS Access. The user constructs the shop, defines the HTML template, adds products and categories, etc. Then the VB exe builds the PHP pages (one for each template page) and the SQL script to run on MySQL. It also uploads everything via FTP and runs the installation/upgrade script on its own. The problem Browsing the website, many products' descriptions are cut before the euro sign. For example, what was supposed to be "Product price €1000" becomes "Product price" The analysis MySQL contains a cutted description until the € sign, so it's not PHP fault The Access databases contain full description with € sign, so it's not fault of the webmaster writing bad description or eDisplay cutting them The SQL that will run once the site gets uploaded, stored on my local machine before upload, contains the € sign The same script, after being FTPed by eDisplay and opened with nano from SSH, shows the € sign messed up like this: ^À vsftpd log reports (obfuscated for privacy) Sat Dec 15 11:16:57 2012 22 xxx.xxx.128.13 1112727 /srv/www/domains/xxxxxx.it/htdocs/db.sql b _ i r xxxxxxx ftp 0 * c which seems to be a binary transfer (and also a huge security vulnerability because you can download the whole database from unauthenticated HTTP) The eDisplay internal FTP client provides no option for ascii/binary transfer modes [Add] Trying to manually upload the SQL file via SFTP shows messing up euro [Add2] Trying to manually upload using Xftp client with explicit ASCII mode doesn't fix too It looks like the file gets uploaded as binary. Perhaps on the customer's previous host it all worked fine because that was a Windows host. The server It's an Azure virtual machine running openSUSE 12.2 with both vsftpd and openSSH The question Without asking the customer to manually upload files using FileZilla or replacing € with &euro;, because he refuses, what can I do on server side to prevent vsftpd to screw up euro sign?

  Read the article

• How can I get Windows to apply its settings?

  - by Jouke van der Maas

  I have a computer with a major problem; it gives a blue screen when the login screen loads. I've been using this guide to troubleshoot the issue, and now I've run into a problem. I have determined the issue is not bad memory or a bad hard drive. According to the guide, this means the problem is in the OS. I've tried to follow the steps, but Windows (Vista SP1) somehow doesn't remember any changes. On every reboot, the computer is in exactly the same state it was in before. Any changes to system settings or files won't be recorded. As this means I can't check what is causing the problem, I can't fix my PC. Is there a way to find out what's causing this? Is it just a mode Windows goes into to protect itself, or is it some other problem? Anything to help troubleshoot will be of great help here. PS. I'm kind of new to this site. If I messed up, please tell me in the comments.

  Read the article

< Previous Page | 494 495 496 497 498 499 500 501 502 503 504 505  | Next Page >