Search Results

Search found 15651 results on 627 pages for 'setup'.

Page 505/627 | < Previous Page | 501 502 503 504 505 506 507 508 509 510 511 512  | Next Page >

• Nvidia RAID 1 Problem. Degraded drives...

  - by Vedat Kursun

  I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

  Read the article

• Nvidia RAID 1 Problem. Degraded drives...

  - by Vedat Kursun

  I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

  Read the article

• WSUS registry file: NoAutoRebootWithLoggedOnUsers entry being ignored

  - by the_pete

  We are using a registry entry to connect our internal workstations to our WSUS server and everything seems to be working except the NoAutoRebootWithLoggedOnUsers entry. Without fail, over the last few weeks, our lab setup as well as our users have been prompted to restart their machines with a 15 minute time out and there's nothing they can do about it. They can't postpone or cancel the restart, all options in the prompt are greyed out. Below is the registry file we are using to connect our workstations to our WSUS server: Windows Registry Editor Version 5.00 [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "AcceptTrustedPublisherCerts"=dword:00000001 "ElevateNonAdmins"=dword:00000000 "WUServer"="http://xxx.xxx.xxx.xxx:8530" "WUStatusServer"="http://xxx.xxx.xxx.xxx:8530" [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate\AU] "AUOptions"=dword:00000004 "AutoInstallMinorUpdates"=dword:00000001 "DetectionFrequencyEnabled"=dword:00000001 "DetectionFrequency"=dword:00000002 "NoAutoUpdate"=dword:00000000 "NoAutoRebootWithLoggedOnUsers"=dword:00000001 "RebootRelaunchTimeout"=dword:00000030 "RebootRelaunchTimeoutEnabled"=dword:00000001 "RescheduleWaitTime"=dword:00000020 "RescheduleWaitTimeEnabled"=dword:00000001 "ScheduledInstallDay"=dword:00000000 "ScheduledInstallTime"=dword:00000003 "UseWUServer"=dword:00000001 There is a bit of redundancy, if you want to call it that, having both the NoAutoRebootWithLoggedOnUsers entry as well as the entries for RebootRelaunchTimeout but we wanted to see if we could either disable the restart, or give our users a larger window within which they could wrap up their work, etc. before restarting. Neither of these entries seems to work, but our priority is getting NoAutoRebootWithLoggedOnUsers working and any help with this would be greatly appreciated.

  Read the article

• Linux: Encryption of a physical LVM volume doesn't imply encryption of its logical subvolumes?

  - by java.is.for.desktop

  Hello, everyone! I installed OpenSuse one year ago on my notebook. I created all partitions except /boot inside an LVM partition. I enabled encryption for it during setup. The system asked me a password on each boot later. Everything seemed fine... But one day I wanted to cancel the boot process and did it with SysRq REISUB. During entering this combination, the system suddenly continued to boot without any password being entered. I had no /home and no swap, but / was mounted! I checked multiple times, it was inside an "encrypted" physical LVM volume. Later I found out that OpenSuse can't encrypt / at all. There is an option to enable encryption for each logical volume, and indeed it fails for /. Later I tried Fedora. The options during partitioning were misleading by same means. I could enable "encryption" of a physical volume and each logical subvolume. With the exception that Fedora actually allowed to encrypt /. Question: What's the point of setting up "encryption" for a physical LVM volume, when it doesn't imply (real) encryption of its logical subvolumes? Did I get something wrong in this whole concept?

  Read the article

• How do I speed up and cache mmap file access over NFS on Linux?

  - by Zan Lynx

  The server and client are both 64-bit Ubuntu 10.04 LTS. The application in question is a custom app that uses mmap() for fast random file access. Its ideal state is when the entire file is cached in RAM. The network connections are really fast 10Gb Ethernet. It is a virtual server blade setup. It isn't the network connections slowing things down because everything performs superbly when using a virtual disk (iSCSI to the SAN). But when we run the application on a NFS home directory mount, performance goes to the dogs. It appears that the Linux kernel isn't caching anything. So it is reading every single disk block needed by mmap() accesses over and over and over again. The NFS mount is done through autofs, which has only default settings. /proc/mounts shows the NFS mount is done with the following options: rw,relatime,vers=3,rsize=131072,wsize=131072,namlen=255,hard,proto=tcp,timeo=600,retrans=2,sec=sys,mountaddr=192.168.11.52,mountvers=3,mountproto=tcp,addr=192.168.11.52 How can I make Ubuntu 10.04 cache the file instead of reloading it all the time?

  Read the article

• Updating ASUS BIOS on Windows 7 64bit

  - by joesavage

  I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

  Read the article

• How can I rapidly switch hosts?

  - by EAMann

  I'm in the process of migrating a forum setup from one version of the software on one machine (older shared Windows host) to a new VPS (Windows Server 2008). To install the software, I used my hosts file to temporarily point the domain at the new IP address. To see the old site, I obviously re-edit the hosts file to remove the reference. But this leaves me constantly adding/removing a # from my hosts file just so I can switch back and forth between the two servers. Is there a way to do this more rapidly? I've found a handful of toggling batch scripts, but all they do is automate the addition/removal of the # character ... so there's still a noticeable lag where I have to repeatedly hit F5 to force my system to detect the new settings. Ideally, I could view both servers at the same time on the same machine. Maybe one through a regular browser session and one through some kind of a proxy. Unfortunately, I don't have the first idea how to set that up. Ideas?

  Read the article

• 2 Computers, same network, different outgoing speeds when uploading to internet?

  - by user117339

  I have 2 work machines in my office, a PowerMac G5 and a MacBook Air. Both behind an IPCop firewall. The PowerMac is connected through a gigabit switch, the MacBook Air is connected through a Netgear 802.11g access point that is then plugged into the gigabit switch. There is also a FreeNAS box, both machines are able to read and write files to it at close to their pipe speeds. The main problem is when I am trying to upload files to the internet at large. The G5 is only hitting 0.1 - 0.25 Mbps. The Macbook is able to hit 2-3 Mbps. The setup (G5 / IPCop / Network) has been the same for 5 years. The issues with the internet speed started about 3 months ago. I hadn't tested on the Macbook at this point. I had complained to the ISP, they said their modem needed a firmware update, did that nothing changed. Reset IPCop, turned off squid, etc. No changes. The ISP switched the office over to a better plan with a theoretical 6 Mbps up, still no change. At this point I tried testing the Macbook, and lo and behold there's the speed. But why? I have tried changing out everything, cables, switches, using another ethernet port on the G5, wiping the system, using DHCP, using manual IPs, changing DNS servers, etc. Nothing works. I figured that if there was something horribly wrong with the network, then internally I would find a similar issue, but that is perfect. iperf, ping, etc show no dropped packets and near saturation of the internal network. I'm at a loss as to what the heck is going on. Any ideas would be appreciated! Below are some screenshots of speedtest.net: G5: Macbook Air:

  Read the article

• Windows 8 install from USB freezes

  - by Rafael Almeida

  I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

  Read the article

• Problems setting up VLC Sever/client streaming

  - by Ayos

  I'm trying to set up a Linux machine as the server and a Windows XP machine as the client. Both machines are connected to the same local network via a Wi-Fi router. I setup the stream with the following properties : http stream port 8080 play locally And not much else. No firewall on the windows client(Windows firewall is disabled) When I try to open network stream via the client machine(Using VLC or Windows Media Player) I get the following errors: Media Player error code : 0xC00D11B3: Encountered a network Problem. VLC Console: main warning: connection timed out access_mms error: cannot connect to 192.168.1.3:8080 main debug: no access module matching "http" could be loaded main debug: TIMER module_need() : 12625.810 ms - Total 12625.810 ms / 1 intvls (Avg 12625.809 ms) main error: open of `http://192.168.1.3:8080' failed main debug: dead input main debug: repeating item main debug: starting playback of the new playlist item main debug: resyncing on http://192.168.1.3:8080 main debug: http://192.168.1.3:8080 is at 0 main debug: creating new input thread main debug: Creating an input for 'http://192.168.1.3:8080' main debug: using timeshift granularity of 50 MiB, in path 'C:\DOCUME~1\Accer\LOCALS~1\Temp' main debug: `http://192.168.1.3:8080' gives access `http' demux `' path `192.168.1.3:8080' main debug: creating demux: access='http' demux='' location='192.168.1.3:8080' file='\\192.168.1.3:8080' main debug: looking for access_demux module: 0 candidates main debug: no access_demux module matched "http" main debug: TIMER module_need() : 0.461 ms - Total 0.461 ms / 1 intvls (Avg 0.461 ms) main debug: creating access 'http' location='192.168.1.3:8080', path='\\192.168.1.3:8080' main debug: looking for access module: 2 candidates access_http debug: http: server='192.168.1.3' port=8080 file='' main debug: net: connecting to 192.168.1.3 port 8080 qt4 debug: IM: Deleting the input main debug: TIMER input launching for 'http://192.168.1.3:8080' : 13397.979 ms - Total 13397.979 ms / 1 intvls (Avg 13397.978 ms) qt4 debug: IM: Setting an input Need Help. Thanks in advance.

  Read the article

• Permissions Issue with Files Generated by PerfMon

  - by SvrGuy

  We are trying to implement some data logging to CSV files using a Data Collector Set in PerfMon (on a windows Server 2008R2 system). The issue we are running into is that we (seemingly) can't control the permissions being set on the log files created by perfmon. What we want is for the log files created by perfmon to have Everyone:F permissions (Full Control for Everyone). So, we have a directory structure setup where all logs go into a folder: c:\vms\PerfMonLogs\%MACHINENAME% (e.g. c:\vms\PerfMonLogs\EvaluationG2) In the above example, c:\vms\PerfMonLogs\EvaluationG2 has permissions Everyone:F (below is the icacls for this directory) EVALUATIONG2/ Everyone:(OI)(CI)(F) NT AUTHORITY\SYSTEM:(OI)(CI)(F) BUILTIN\Administrators:(OI)(CI)(F) BUILTIN\Performance Log Users:(OI)(R) When the data collector set runs, it creates new sub folders and files within c:\vms\PerfMonLogs\EvaluationG2, e.g. (C:\vms\PerfMonLogs\EVALUATIONG2\M11d26y2012N3) Each of these directories and files has the following permissions: M11d26y2012N3 NT AUTHORITY\SYSTEM:(OI)(CI)(F) BUILTIN\Administrators:(OI)(CI)(F) BUILTIN\Performance Log Users:(OI)(R) So these new folders and not simply inheriting permissions from the parent folder (don't know why). Now, we tried adding Everyone:F using the security tab on the collector set (No dice). Any ideas? How do we control the permissions on the log files generated by perfmon data collector set?

  Read the article

• Limited bandwidth and transfer rates per user.

  - by Cx03

  I searched for a while but couldn't find anything concrete, hopefully someone can help me. I'm going to be running a Debian server on a gigabit port, and want to give each user his/her fair share of internet access. The first objective is easy - transfer rates (speed) per user. From what I've looked at, IPTables/Shorewall could do the job easy. Is this easy to setup, or could one of you point me at a config? I was hoping to limit users at 300mbit or 650mbit each. The second objective gets complicated. Due to the usage of the boxes, most of the traffic will be internal network traffic that does NOT get counted to the quota. However, I still need to limit the external traffic, and if they go over, cut off access (or throttle traffic to a very low speed (10mbit?)). Let's say the user has a 3TB external traffic limit. The IF part is: If the hostname they are exchanging the traffic with DOES NOT MATCH .ovh. or .kimsufi. (company owns multiple TLDs), count to the quota. Once said quota exceeds 3TB, choke them. Where could I find a system to count that for me? It would also need to reset or be able to be manually reset on a monthly basis. Thanks ahead of time!

  Read the article

• Ram configuration 4x4 or 2x8?

  - by Carl B

  I am looking to upgrade my Ram to 16gigs and I am wondering if there is any distinct advantage of the way I do it. That being a 4x4 or 2x8 set up. In all my searching there have been a number of pros for each profile. I can find no benchmarck results for either setup as a compaison. So, if there are 2 profiles of the same speed, same voltage, same timing and same cas what would perform better or have a better over all benafit? A few examples from my search - a 4x4 set would lend a benafit in that if one stick failed, you only lose 25% of your Ram vs 50% in a 2x8 set up. a 2x8 set up would have less strain on the memory controler and motherboard. a 2x8 would generate less heat. a 2x8 set up is easier to over clock (not part of my need, but alot of the comparisons circled around the overclocability ease of the 2 stick set up). There is one outstanding benafit that I have found in at least the target company I have looked at and that is price. The 2x8 is nearly half the cost. My motherboard supports a max of 16 gigs and I have a 64 bit OS. Has anyone seen any performance comparisons or is 16 gb just 16 gb no matter how you slice it? And is there any merit to the above pros? Edit: as per the mobo specs - Main Memory • Supports four unbuffered DIMM of 1.5 Volt DDR3 800/1066/1333/1600*/1800*/2133* (OC) DRAM, 16GB Max

  Read the article

• Bridging networks problems

  - by Eric

  In my setup I have 3 computers and 2 (wireless d-link) routers. Computer1 has ethernet and wireless interfaces ethernet : 192.168.0.x (DHCP) wireless : 192.168.10.254 (static) Computer 2 has ethernet with two ips ethernet1 : 192.168.0.90 (static) ethernet2 : 192.168.10.110 (static) Computer 3 is a particular device with a hardcoded ip that I can't change wireless : 192.168.10.41 (static) Router1 manages internet and DHCP for network 192.168.0.0/24 Router2 is more complicated. I don't use DHCP. I use it to bridge between both networks. Its static ip is 192.168.10.1 Computer1 can ping Computer2. Computer1 can ping Computer3. Computer1 can ping Router1. Computer1 cannot ping Router2. Computer2 cannot ping Computer3. Computer2 can ping Router2. Router1 can ping Router1 Router2 can ping Computer2 Router2 cannot ping Computer1 Router2 cannot ping Computer3 This is very weird. Router2 manages the wireless connection, it should be able to ping its own computers right? My question is obviously : How can I make it so Computer2 can access everything else. This is a traditional case of "it was working before christmas and now it doesn't". The ethernet wiring is as follow : [ Computer1 ]----[ Router1 ]---[ Router2 ]---[ Computer3 ] I am using switch (lan) ports on Router1/2.

  Read the article

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• One workstation gets slow access to the server, but others are fast

  - by Mike Hanson

  I've just setup a machine with Windows Server 2008. It hosts various services, like IIS, POP3, SMTP, Music for Squeezeboxes, VNC. All was working well for the first week or so. One day I needed to create a mapped drive on the server, so it could access files on my workstation. Windows indicated that Network Discovery was needed, so I turned it on with the "Home / Office" option (rather than "Public"). This may be coincidence, but since that time I've been having troubles accessing various services from my main workstation (running Windows 7/64): POP3 continued working correctly, but SMTP was delayed or failed entirely. (Telnet took 20 seconds to connect, but Outlook would never send messages.) VNC failed entirely. I reinstalled it on the server, and now it works but feels sluggish. The music web server was extremely delayed and usually failed. I tried reinstalling, and now it takes about 30 seconds to show the page name on the browser tab, and another 30 seconds to display any page contents. Other machines on the local network seem fine, as do machines connected via the Internet. I don't believe I changed anything on my own machine that would cause this. I considered the possibility that my anti-virus was involved, so I uninstalled AVG (commercial version), but that didn't help. I installed Norton 360 after that, and it didn't complain of viruses on my machine, and the delays remained. Because only my machine is affect, I'm tempted to blame it, except that reinstalling software on the server improved the situation, so there is almost certainly something going on with the server too. The firewall has all the necessary ports open, and it works fine for the other workstations (including external machines connected via the Internet), which indicates that it should be OK. Any ideas?

  Read the article

• sub application and virtual directory file permissions

  - by Zeus

  I have a website setup in IIS7, exampledomain.com. Under the application exampledomain.com lives a sub application cms. In a rather convoluted way, we have content in our cms system in this sub-app, under cms\content\{generatedfoldername}. So to access an image in this content, the full URL would be http://www.exampledomain.com/cms/cms/content/{generatedfoldername}/image.jpg, (yes, cms twice...) and this works just fine. Now, we have a virtual directory under the parent website, called stuff which points at the content of the cms. So I should be able to get to the image using the url http://www.exampledomain.com/stuff/{generatedfoldername}/image.jpg. Unfortunately this gives a server 500 error "There is a problem with the resource you are looking for, and it cannot be displayed." Whilst you do have to log into the cms system to access any of the admin pages within, I don't think the image files are protected by login, or else the first example URL wouldn't work, right? Also it's a server 500 error, rather than a 403. I'm sure I must be missing something obvious here- will the virtual directory be using the permissions defined in the parent application, or the subapplication to which it is pointing? Or is there some other permissions I may have missed? Sorry, that was a bit long, thanks for reading all the way down here! (I also must point out that I'm pretty new to the server management stuff.) edit: also, we have <location path="." inheritInChildApplications="false"> specified in the webconfig of the parent app, so it's hopefully not the issue described in this config file hierarchy article.

  Read the article

• Interaction between two Clouds

  - by Snehal Masne

  I have setup the Cloud-A with 1 - [CLC+CC] and 2 - [NC] computers. I have another Cloud-B with same configuration using the Ubuntu Enterprise Cloud Both of them working fine individually, in the same LAN. Now if I want to add the NC of Cloud-A to CC of Cloud-B, [in case the resources of Cloud-B are exhausted] how can I make it possible ? I guess this calls for the interoperability stuff... Could you please explain what happens exactly when we ask for instance, the direct interaction happens between the client and NC or it goes through the CLC and CC ? What I want to say is, say there are multiple cloud providers. A user is subscribed to any one of them, say Cloud-A for IaaS. As the requirements are dynamic, all the resources of Cloud-A may get exhausted. There may be another Cloud-B which can provide the services but that Cloud-A can't ask the client to go for Cloud-B. So if it is possible to have some co-ordination between this two providers to share resources mutually, making client fully unaware of whats going on in the background....?

  Read the article

• Switched to new router and now experiencing lag?

  - by Mr_CryptoPrime

  I switched from a dynex-802.11b/g to a Netgear-802.11b/g/n just yesterday. My router is down stairs because my phoneline upstairs is retarded....but my PS3 is still upstairs (SOCOM: Confrontation is game I am experiencing issues). I have done everything I can to make sure the connection is solid and have checked the status and it has been as high as 80% and usually lingers at about 60%. I thought about upgrading my bandwidth from 1.5mbs to 7mbs, but I am guessing something is wrong if it worked fine before? Now the game seems more laggy and my voice chat is choppy. Others seem to receive my voice data fine because I can hear my own feedback clearly from other players (if you are in close proximity to another player and speak and there volume is loud enough sometimes you can hear yourself). I wonder if I port forward or setup DMZ then it will be fixed, but I am not sure and don't know quite how to do it. Has anyone else ever experienced this when switching routers? What did you do to fix it? Thanks!

  Read the article

• How can I get mouse capture to work in virtualbox when I move guest window to second monitor?

  - by Dan

  I'm running VirtualBox on a Win7 host. Guest OS is Centos. My setup is a laptop (screen 1) with a huge external monitor (screen 2). I'm only telling Centos there is one monitor though. When I start up VirtualBox on screen 1, the mouse capture works fine. I don't have mouse integration because (I think) the kernel on Centos is too old to support it. That's fine, I don't mind doing the Right-Control thing. The problem I have is that when I drag the whole VM window over to my second monitor, the mouse capture doesn't work right anymore. I click inside the VM and can move the VM cursor a little bit, but I can't always get to the edges of the VM screen -- before I get all the way to an edge, the cursor will escape from the VM as if I had hit right-control. But it's still captured according to the icon, and if I then hit right-control, the guest cursor jumps to a different screen location. My workaround: if I have the VM window mostly on screen 2, but a small corner of it still on screen 1, then the mouse capture works correctly. Is there a setting to make this work better?

  Read the article

• Terminal Server CPU usage at 100%

  - by Light1c3

  I'm running a terminal server with around 50-60 users,and every so often the server will go from 40% usage to 100%. I took a closer look an it seems every time this happens, a different user or two seem to be caught in a loop and end up using < 30% where the rest of the users only use a maximum of 5%. The company behind the software we use clame it's due to the servers inadequate hardware (It's a VM system running on a dual - quad core setup) which to me sounds like BS! I'm fairly new to this level of IT so if I misspoke I apologize. I have no way to prove it but I believe adding more raw hardware power wont do me any good as this to me seems like a bug in their software, and it will suck up as much ( or little) CPU as it's given. The VM in question has 4 vCPU cores and 12 GB RAM available, and is running Windows Server 2008, 64-bit Thanks in advance for your help! Note: I have the same question posted on SO, but was pointed in this direction so just in case, here is a link to the post http://stackoverflow.com/questions/17276602/termserver-cpu-at-100

  Read the article

• Route53 only for wildcard subdomain

  - by Philippe Gerber

  We recently moved our web application to AWS. One thing that is still managed by our old hoster is DNS. OLD HOSTER example.com. NS <Old hoster's name server> example.com. A <ElasticIP on EC2 instance> *.example.com. CNAME example.com. ... I'm now trying to setup and play around with Route53 and use it for name resolution of our EC2 instances. ROUTE53 web-01.aws.example.com. CNAME ec2-xx-xx-xx-xx.eu-west-1.compute.amazonaws.com. web-02.aws.example.com. CNAME ec2-xx-xx-xx-xx.eu-west-1.compute.amazonaws.com. ... Now my question: Is it possible to forward DNS queries for *.aws.example.com to Route53 (ns-xxxx.awsdns-59.co.uk.)? What kind of record would I have to add?

  Read the article

• PXELinux and compressed kernels/images

  - by Yvan JANSSENS

  Is it possible to boot compressed kernels with a compressed initrd with PXELinux? First, a little background: We created a custom Linux distro, for diskless OpenCL computing nodes. We want those nodes to fetch their OS from the network. Our Distro is composed out of a kernel (duh) and a large initrd which is loaded into RAM and everything is executed from there. We chose to run everything off the initrd for two reasons: NFS was not an option to serve the filesystem's extra contents Fast file access from RAM. No persistent storage needed, data and config is pulled dynamically through a SOAP service. Now our initrd is about 450M in size. At our network speeds, it takes about two to three minutes to load a single client. Will compression speed up te downloading, and if yes, which one should be used? Is LZMA supported by PXELinux, or do we need to stick to bzip2 or gzip? Because of the 2-3 minutes loading time, booting 15 nodes over the same network link takes quite a lot of time. We decided not to use hard drives or CD/DVD drives, for financial reasons (cheapest HDD @ €30 times 15 is a lot of money saved ;-) ) So, our question is: what compression options are available for this setup? And how do we do this? Thank you for your time! Yvan Janssens

  Read the article

• Basic connectivity issues between Win 7 and XP mixed wired/wireless network. [Solved]

  - by Pulse

  Setup: Windows 7 x64 Ultimate desktop hard wired to Asus WL500gp router (WL500gpv2-1.9.2.7-d-r1445 firmware) Several Bridged VirtualBox VM's running XP, 7, ubuntu server 10.04, Mint 9 and SuSE 11.2 Win XP Pro SP3 notebook with D-Link Airplus wireless network card. No firewall or other security software currently running on either platform (at least for the duration of the test) Situation: Router is acting DHCP server Clients are receiving correct addresses and additional parameters Internet connectivity is available from all clients Windows 7 sharing is set to Network type = work (not home group) NetBT is disabled on all clients using smb over TCP What I can do: I can ping the router and internet addresses from the wireless XP notebook I can ping the Win 7 desktop and any VM from the XP wireless notebook I can ping all devices from the router All VM's and 7 can ping each other and the router as well as Internet addresses What I can't do: I cannot ping the XP wireless notebook from either the Win 7 desktop or the VM's; it always returns a destination host unreachable error. Tracert resolves the name or the XP notebook but also returns a destination host unreachable. From the above it would seem that something is blocking connectivity in a single direction (from the Win 7 box to the Win XP notebook) only but the router can ping the XP notebook. Some fresh input would be most welcome, as this is beginning to drive me batty. Thanks

  Read the article

• Graphics artifacts/distortion with Win7 and nVidia

  - by Gepard

  Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

  Read the article

< Previous Page | 501 502 503 504 505 506 507 508 509 510 511 512  | Next Page >