Search Results

Search found 15651 results on 627 pages for 'setup'.

Page 507/627 | < Previous Page | 503 504 505 506 507 508 509 510 511 512 513 514  | Next Page >

• User Group Policy in Server 2008 to set Default Profile settings

  - by Chris

  I have computers to deploy and want to apply changes to the default user policy on these PCs automatically. What's the best way to do this? Our current procedure is: Create the computer account in an OU called "Deployment" on our server Unbox the PC Login as the user who will be receiving the PC Change settings (pre-configure outlook, authorize Office, etc.) move computer account to correct OU Place the PC on the users desk. I would like to make as many of the changes in step #4 with Group Policies applied to the Deployment OU if possible since they're largely repeated for every computer. There are a dozen policies created and the computer ones apply correctly but the user policies do not. I understand this is because the end user is not in our "Deployment" OU. I don't want to apply these settings to the user at their current station just the new PC I'm working on. I believe I have the desired effect with Group Policy Loopback Replace enabled on policies that need user policies changed but this just feels wrong/inefficient/complicated to maintain. Am I doing this correctly? Is Group Policy Loopback the only way to change user accounts on one computer? What do you do to setup a user on a new PC?

  Read the article

• upstart scripts: run a task after networking goes up

  - by The Journeyman geek

  I'm working on moving my current server setup to newer hardware, and migrating from ubuntu karmic koala to lucid lynx. Currently i'm using gw6c (compiled from the gogo6 website, as opposed to the version from the repositories) to get ipv6 access for my systems. On the karmic koala system, i used simple init.d script to get the ipv6 client started #! /bin/sh /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf I figured since this runs at any runlevel, it should translate to respawn console none start on startup stop on shutdown script exec /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf emit free6_ipv6_started end script this works fine started from initctrl, but it apparently fails to start when it boots. - its status being stop/waiting. It works fine (and respawns) when started otherwise.Any ideas on where i'm going wrong, and what would be the appropriate 'start on' arguement? EDIT: the exact error is 'init: gw6c main process (xxx) ended with status 8' followed by the process respawning , with xxx being a PID i suspect. I'm also half suspecting this is cause gw6c starts before networking does, and i need my eth0 up before gw6c is

  Read the article

• Giving the root user priority to maintain Debian (while server collapsing under heavy load)

  - by Saix

  Is there any way to setup Debian to prioritize any or specific root's activity before every other? For instance, several times per year something gets wrong (usually man's fault by overstressing apache/mysql) and system gets unresponsive under heavy load like 200 (8-core cpu). I know there are limits for php scripts to run then kill, but that's not the way because this limit has to be at least 45 minutes long. The problem is, until I'm able to login via SSH and let apache/mysql restart under this server stress, it nearly hits these 45 minutes anyway. Also hardware restart causing usually to run fsck at boot time on all harddrives since it's usually pretty long the box haven't been restarted. I was told it's really not good idea disabling fsck but then again, it takes more then hour to complete. What is the fastest way to restart apache/mysql? Is there any way to give ssh users or root user higher priority so the logging in and completing these restarts (rather stops though) commands wouldn't take so long? One comes to my mind.. use NICE for apache/mysql but no way. I can't risk limiting those two vital apps 24/7 or could I? I'm a little bit scared if any other system process wouldn't slow the pages down too much. Any backup process, swap (if any) etc. There is pretty heavy PHP framework with 20k visits a day, so it needs every hw/sw resource available. I can't throttle it the whole time, just in certain points when system gets unresponsive, so I could maintain it.

  Read the article

• How do I connect to and factory reset a Catalyst 3560 Switch?

  - by Josh

  My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

  Read the article

• connections in FIN_WAIT and CLOSE_WAIT state

  - by Raj

  I would like to elaborate the setup so You guys can understand the question and answer more accurately. I have HAProxy as load-balancer, 4 webservers (apache 2.2.3) and one database server (MySQL 5). I am monitoring these servers by nagios. I have disabled the keepalive on apache as we have only 8GB of memory. Now what happens whenever I receive alerts for high memory and cpu utilization, I have observed that the connections from apache to database server hang in established mode (keepalive with timeout value of 7200) and at other side means connections between haproxy and apache shows status as FIN_WAIT on haproxy server and CLOSE_WAIT at apache side. I also see the huge memory swapping and apache taking the most of the memory. I did strace on apache process and did not find any information. strace gets attached to apache process but did not produce any output. The processlist on Mysql server show s those processes in sleep mode. The application on webserver is Magento a php application. if you need further information please let me know. Thanks.

  Read the article

• Xamp on ubuntu serves php source for root url only

  - by mazaryk

  Hey, Okay, so installed xamp on my ubuntu machine, started it up and everything worked. Apache ran my php app just fine (including requests to the root url "/"). However, after the first reboot since installing, when I request "http://localhost/" apache serves up the index php page as a phtml source file. All other urls (like "http://localhost/login") work as expected. Backgound: The only modification I made to xamp was to setup a vhost for my app. The app uses an .htaccess file where I define some rewrite rules (the app is an MVC framework and all urls are rewritten to a single entry point php file). I'm using Xamp because I need php = 5.3.0. I know apache will serve up the source of a php file when it doesn't know to process php files. But the config does indeed have "AddType application/x-httpd-php .php" and as I said, the app works for all urls except the root "/" (and only since I've rebooted). The .htaccess file does contain a DirectoryIndex directive. xamp 1.3.7a Ubuntu 9.10 Any ideas?

  Read the article

• Huh? JDK not found? (on Windows 7 64-bit)

  - by Android Eve

  I am setting up a development environment for the latest Android 2.3 on a fresh install of Windows 7 64-bit. I first installed the 64-bit JDK 6 (jdk-6u23-windows-x64.exe). Then, I installed 64-bit Eclipse Classic 3.6 (eclipse-SDK-3.6.1-win32-x86_64.zip). Then, I proceed to install the Android SDK Starter Package: installer_r08-windows.exe. But... upon start it says: "Java SE Development Kit (JDK) not found." Why? I just installed it. Is this a mismatch between 32-bit and 64-bit? How do I solve this? Update (1): I tried setting the %JAVA_HOME% environment variable, as well as setting the Installed JREs in Eclipse, as suggested below. None of these solved the problem. It appears that I am not the only experiencing the problem, as this thread suggests: http://stackoverflow.com/questions/1919340/android-sdk-setup-under-windows-7-pro-64-bit I wonder whether there is a 64-bit version of the Android SDK. Update (2): I used the zip version instead (android-sdk_r08-windows.zip), ran android.bat, updated all SDK packages, and installed the ADT plugin (8.0.1), not before having to check: 'Contact all update sites during install to find required software'. We'll see how this goes... Update (3): It worked! (going to accept @bubu's answer shortly) -- but why doesn't the emulator include the HelloAndroid app when I run it (Ctrl+F11) from Eclipse?

  Read the article

• Should I be able to Windows Phone 8 emulator running with this AMD config

  - by pete

  I have just bought a new system as follows * AMD A4-5300 Trinity 3.4GHz * Gigabyte GA-F2A55M-DS2 Motherboard I checked and the A4-5300 supports Virtualisation. I have run the SLAT checking tool and it says that my machine supports SLAT. Been into the BIOS and ensures that SVN is enabled. I have also run the coreinfo tool that indicates that SVN is not valid fort the machine nor is NPT.. not sure why this conflicts with the true BIOS setting (I checked with GIGABYTE and seems that NPT and NX are not options that can be set in the BIOS) But.. when I run the emulator I it hangs - I can see some activity in Hyper-V manager, but it doesnt get very far and no meaningfull error messages. Been working the plethora of suggestions to get around this, but so far, nothing has worked. My question is should this setup allow the WP8 emulator to run. I am positive the CPU supports virtualisation, but are there issues with the motherboard here? I have spent a huge amount of time on this so far....am I wasting my time with the current configuration, or should it work? thanks

  Read the article

• visually documenting web server configuration and infrastructure

  - by Alex Ciarlillo

  I have just finished a large re-organization and update of our institutions web server(s). This server hosts 3 virtual hosts, 3-4 blogs, 2 wikis, some legacy static HTML pages, and many hosted documents (PDF, .jpg, .xls). I have organized the site into a structure of something like: /var/www/sites/vhost1, vhost2, vhost3 .../wordpress/blogX .../mediawiki/wikiX Data is in a seperate directory structure so I can run a cron task over it to make sure it is all writeable and such. I then symlink to these data directories for each application. /var/www/data/vhost1, vhost2, vhost3 .../wordpress/blogX/uploads .../mediawiki/wikiX/images All Apache configs are in /etc/httpd/conf.d/vhosts.d/vhost1,2,3.conf On top of this there is also a testing server which mirrors this setup. Once changes are fully tested, they are rsynced down to the live server. All the wordpress installs and mediawiki installs are straight form SVN and updates are done by switching branches or "svn up". So my question is how can I best document to share with a) co-workers, b) possible future replacement, c) myself 6 months from now. Obviously I can make a wiki page, excel document, whatever and fill it with text, but I am looking for a more visual representation that I can use to explain the architecture to less-technical people. Ideally it would be awesome if this visual representation could then be expanded to get more technical details.

  Read the article

• Fixing Windows install by connecting it's hard drive via USB to a different laptop

  - by Jason

  I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

  Read the article

• Fixing Windows install by connecting its hard drive via USB to a different laptop

  - by Jason

  I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

  Read the article

• Windows 7 boot manager not localized on UEFI systems

  - by Massimo

  I originally posted this on SuperUser because I discovered this behaviour on my home computer, but this seems to be a general issue on UEFI systems, thus I'm posting here too; I also hope someone here can shed some light on what's going on. Italian version of Windows 7 x64 SP1, same installation media used for both situations. When running on BIOS systems, the boot manager is fully localized, both for the loading screen and for the F8 boot menu. When running on UEFI systems, the boot manager always runs in English, even if it's correctly configured to use the it-IT locale, as BCDEDIT clearly shows: Windows Boot Manager -------------------- identificatore {bootmgr} device partition=\Device\HarddiskVolume1 path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale it-IT inherit {globalsettings} default {current} resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} displayorder {current} toolsdisplayorder {memdiag} timeout 30 Caricatore di avvio di Windows ------------------- identificatore {current} device partition=C: path \Windows\system32\winload.efi description Windows 7 locale it-IT inherit {bootloadersettings} recoverysequence {9ef36aa8-4188-11e3-909d-d32f0c3871c8} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} nx OptIn I also noticed something strange here; the motherboard setup shows "Windows Boot Manager" as the main boot option, while the actual boot disk is listed as the second one. Looks like the Windows Boot Manager is actually being loaded from somewhere else than the first partition of the first disk... what's going on here? Update I've also checked the EFI boot manager using bcdedit /enum FIRMWARE. That one looks correctly localized, too: Boot Manager per firmware --------------------- identificatore {fwbootmgr} displayorder {bootmgr} {9ef36aa4-4188-11e3-909d-d32f0c3871c8} {a30e8550-47e4-11e3-9ad1-806e6f6e6963} timeout 1 Windows Boot Manager -------------------- identificatore {bootmgr} device partition=\Device\HarddiskVolume1 path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale it-IT inherit {globalsettings} default {current} resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} displayorder {current} toolsdisplayorder {memdiag} timeout 30 Applicazione firmware (101fffff) ------------------------------- identificatore {9ef36aa4-4188-11e3-909d-d32f0c3871c8} description CD/DVD Drive Applicazione firmware (101fffff) ------------------------------- identificatore {a30e8550-47e4-11e3-9ad1-806e6f6e6963} description Hard Drive

  Read the article

• Ubuntu 12.04 as router with 2 nic

  - by Blue Gene

  I have been trying this setup for weeks and still can not make this to work... ubuntu 12.04 64 bit with 2 nic nic1: eth0:192.168.2.33 -static ip with internet access (connected to modem) nic2: eth1:192.168.1.2 -static ip connected to LAN. enabled ip_forward on ubuntu box net_ip_forward = 1 on the LAN with ip address 192.168.1.5 specified gateway as 192.168.1.2 and able to ping gateway.But can not ping public address.What am i missing? on router box: route -n Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 tried ip route add 192.168.2.0/24 via 192.168.1.2 dev eth0 route -n on LAN 192.168.1.5 Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.2 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 192.168.1.2 255.255.255.0 UG 0 0 0 eth0 iptables default policy is to accept all. tracepath 8.8.8.8 from LAN 1: 192.168.1.5 0.060ms pmtu 1500 1: 192.168.1.2 3.367ms 1: 192.168.1.2 3.764ms 2: no reply Is there a way to make this work,other than NAT ing.

  Read the article

• Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

  - by user94217

  I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

  Read the article

• How to route outbound traffic to specific domain "XYZ.org" via a specific NIC or public/static IP?

  - by user139943

  Within the next week or so, I'll be setting up an AT&T U-verse modem with 5 usable static public IP addresses. I plan to register a domain name to 1 of the 5 static IPs (remaining 4 unregistered), and run a website from a single server setup in my home LAN. I'll skip the long winded reason why, but I need to somehow route outbound traffic (originating from my server) destined for one public domain (i.e. http://www.sample.org) through one of the UNREGISTERED static IP addresses ONLY. Basically, I want this public domain to see connections coming from an IP address and not my domain name. If it makes it easier, this can apply to all outbound traffic from my server as long as it doesn't impact users browsing my website! Inbound connections should go through the domain name / registered public IP. Can I accomplish this with my single server with one or multiple NICs? Do I need multiple servers and set one up as a proxy? Please help as my background is in software and not networking, and I don't think I can accomplish this at a software level (e.g. Java). Thanks.

  Read the article

• Scaling a node.js application, nginx as a base server, but varnish or redis for caching?

  - by AntelopeSalad

  I'm not close to being well versed in using nginx or varnish but this is my setup at the moment. I have a node.js server running which is serving either json, html templates, or socket.io events. Then I have nginx running in front of node which is serving all static content (css, js, etc.). At this point I would like to cache both static content and dynamic content to memory. It's to my understanding that varnish can cache static content quite well and it wouldn't require touching my application code. I also think it's capable of caching dynamic content too but there cannot be any cookie headers? I do use redis at the moment for holding session data and planned to use it for other things in the future like keeping track of non-crucial but fun stats. I just have no idea how I should handle caching everything on the site. I think it comes down to these options but there might be more: Throw varnish in front of nginx and let varnish cache static pages, no app code changes. Redis would cache dynamic db calls which would require modifying my app code. Ignore using varnish completely and let redis handle caching everything, then use one of the nginx-redis modules. I'm not sure if this would require a lot of app code changes (for the static files). I'm not having any luck finding benchmarks that compare nginx+varnish vs nginx+redis and I'm too inexperienced to bench it myself (high chances of my configs being awful). I'm basically looking for the solution that would be the most efficient in terms of req/sec and scalable in the future (throw new hardware at the problem + maybe adjust some values in a config = new servers up and running semi-painlessly).

  Read the article

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• GPG - why am I encrypting with subkey instead of primary key?

  - by khedron

  When encrypting a file to send to a collaborator, I see this message: gpg: using subkey XXXX instead of primary key YYYY Why would that be? I've noticed that when they send me an encrypted file, it also appears to be encrypted towards my subkey instead of my primary key. For me, this doesn't appear to be a problem; gpg (1.4.x, macosx) just handles it & moves on. But for them, with their automated tool setup, this seems to be an issue, and they've requested that I be sure to use their primary key. I've tried to do some reading, and I have the Michael Lucas's "GPG & PGP" book on order, but I'm not seeing why there's this distinction. I have read that the key used for signing and the key used for encryption would be different, but I assumed that was about public vs private keys at first. In case it was a trust/validation issue, I went through the process of comparing fingerprints and verifying, yes, I trust this key. While I was doing that, I noticed the primary & subkeys had different "usage" notes: primary: usage: SCA subkey: usage: E "E" seems likely to mean "Encryption". But, I haven't been able to find any documentation on this. Moreover, my collaborator has been using these tools & techniques for some years now, so why would this only be a problem for me?

  Read the article

• Good support to multiple desktops AND multiple monitors in Linux (Ubuntu)?

  - by Somebody still uses you MS-DOS

  I'm starting to have A LOT of opened windows in my machine. Sometimes within a project, I have e-mail/task management/personal e-mail/twitter, and a lot of different opened applications/terminal in my Linux environment. Nowadays I have 4 worspaces: Corporate management (e-mail) and corporate messenger; Work (Documents, Requisites) Dev (Development, All gVim windows, terminal and Firefox for development) Personal (Personal stuff: personal e-mail, delicious, twitter and so on) Sometimes it would be interesting to have different workspaces to projects instead of this configuration I have nowadays that are classes of work (bad name, I know, but I think you got the idea). I'm starting to think about using two monitors: one with Corporate Management, Work and Personal. The second monitor is only the development state: each workspace here is about a project being worked on instead of groups of works like before. A workspace may be implementing different classes for example. My question is: I just want to change to a second monitor using the mouse. I want to still be able to change workspaces in the same monitor using keyboard shortcuts. The keyboard shortcuts wouldn't change monitors, just worskpaces on the same monitor. Does Linux (Ubuntu 10.04 Lucid Lynx) support this envisioned setup? If so, how?

  Read the article

• How do I serve Ruby on Rails applications on Windows Server 2008?

  - by Adam Lassek

  I have spent the last several hours attempting to get Ruby on Rails running on a Windows server with no luck. At first I tried configuring a test application through IIS7's FastCGI support, but the documentation for this is not very good. I've been following this blog entry, and this one, and this one, and this one but everything seems to be missing major steps, or are out of date. And every article keeps linking back to this Howto from rubyonrails.org that doesn't exist. The sense that I'm getting is that even if I manage to make this work, IIS' FastCGI isn't good enough to use in a production environment anyway. So it looks like my best bet is to setup a reverse proxy in IIS that points to Apache & Mongrel/Passenger using ARR and UrlRewrite. Is there anybody else out there stuck deploying a Rails application on a Windows stack? Am I on the right track? Can you give me a better idea of how to configure this? I believe Plesk already installed an instance of Apache/Tomcat running on this server using a different port, so adding another virtual host shouldn't be difficult; the hardest part seems to be setting up the reverse proxy through IIS.

  Read the article

• Why can't I connect to my home SSH (SFTP) server? What am I doing wrong?

  - by Rolo

  I am new to this topic of creating a SFTP server on one's computer. I would like to be able to access the folder on my Windows XP computer via SFTP from another computer or a phone. The following is what I have done so far: I have installed SSH Windows and everything is setup correctly because I can access it (the folder on my pc) via WinSCP. I however cannot access it from my phone. It doesn't connect. The phone can be on the same wireless network as the Windows XP computer, but I would prefer to be able to access this when not in the same network. Now, from what I have read and understood, the following is the information needed to connect: 1) Host Name: This would be my computer's ip address which I access by typing ipconfig in a cmd prompt (I access this easily on my computer because I simply put in localhost or 127.0.0.1) 2) Port Number: That would be port 22 (I have also added this to my router in the port forwarding section). 3) Username: This would be my Windows XP username. This however is my full name, including my middle initial followed by a period. I am wondering if this is maybe causing problems in accessing it from my phone, since the name has spaces and punctuation (the period). 4) Password: The password of my Windows XP computer Extra Info: When I say phone, I mean an Android phone and I am using an ftp / sftp app to access my pc via the phone's cellular network (I also tried the wireless, but that didn't work as well). I have tried more than one program. On one program it tells me Connection timed out and on another it tells me "timeout:socket is not established" Also, I know that I can use the site noip, but I prefer to connect this way first. Also, because I am new to this, I would like to look into what exactly noip is doing and if they would be seeing my files as they are transferred from phone to pc. Thanking you in advance for your help.

  Read the article

• How to get a list of Dovecot IMAP users

  - by Colt McCormack

  How do you get a list of users for a dovecot email server that connect via IMAP (as opposed to POP)? Our server is setup to authenticate via LDAP/PAM. Is there an easy way to get a list of the users who are accessing their mail via IMAP, rather than POP? I am about to migrate our server to Google Apps and want to migrate all of the mail for my IMAP users only (couple hundred out of several hundred total users). POP mail will be migrated separately from the client end obviously. I would much rather migrate only the IMAP users rather than the whole domain which would include migrating a bunch of POP mail left in the server that has already been read/sorted/deleted in the client's email program. Migrating all of that extra useless leftover POP mail could waste weeks of migration time. I suppose parsing some logs to see who has connected on an IMAP port (995 or 993) would give me a list would work if someone could help me do that. I know I have the raw dovecot logs, but am hoping for a cleaner solution.

  Read the article

• Strange Domain name under the same IP Address

  - by Mike Chip

  There's something really weird happening in my server. But first things first: I wanted to have my website and chose the domain name "myowndomain.com", Now on my domain registrar I point "myowndomain.com" to the address of my recently setup VPS, let's say 50.50.50.50 So I installed everything I needed to run my website, and I started to notice strange queries coming from different IP Addresses. Like these [client 123.123.123.123] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php [client 456.456.456.456] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php or like this (Really a long line, I cut some things) GET /?s=vod-show-id-22-area-%E5%85%B6%E4%BB%96-language-%E9%9F%A9%E8%AF%AD.html HTTP/1.1" 301 295 "http://v.strangedomain.com/?s=vod-s ...[cut]... spider" That above is happening the most. The 'strangedomain.com' returns the same IP address of my VPS which my website is hosted on. The whois of such domain shows it's registered to a chinese. But the street name didn't look so right (like a huge single word), so I think all of that info might be fake, but still might be a chinese. I also noticed that all 'clients' trying to access the 'strangedomain.com' is coming from china. If I type in the browser 'strangedomain.com', I see my website. I'm worried, because my website is actually an e-commerce. I don't know if 'strangedomain.com' WAS a website on 50.50.50.50 in the not so far past, or if it's something else.

  Read the article

• Gentoo server time issue, can't manually set time, NTPD won't correct, too big of a time difference

  - by kevingreen

  So, my server is living in the future, unfortunately I can't get lottery numbers, or stock picks out of it. It thinks this is the time: Thu Nov 7 04:07:18 EST 2013 Not correct, I tried to set the time manually via date in a few ways # date -s "06 NOV 2013 14:48:00" # date 110614482013 -- same output, same problem Which outputs Wed Nov 6 14:48:00 EST 2013, but when I check the date again, it's still set to Nov 7th 0400 or whatever. I checked my system messages, and I see this pop up often: Nov 7 03:54:00 www ntpd[4482]: time correction of -47927 seconds exceeds sanity limit (1000); set clock manually to the correct UTC time. Which makes sense, we're way off the correct time. But I can't seem to manually fix it. So now what? Also, I'm wondering if my hardware clock is setup correct, hwclock doesn't return any values. Would that be causing issues? This is a virtualized server, I don't have direct access to the hypervisor, but I can talk to who does, assume I can explain myself well enough. Thanks

  Read the article

• Odd one: IE6 showing the "view source" command enabled when I was expecting it to be disabled.

  - by caerphilly

  Hi, OK, I admit this problem is odd. I'm just trying to understand why IE is behaving the way it is. I realise that logic may not apply here :) I have Internet Explorer 6 (Sp1) running on Windows 2000. The IE option "Do not store encrypted pages to disk" is checked (enabled). The temporary internet files folder is empty. TEMP and TMP environment variables are set to valid folders. I'm connected to a web server over SSL. The web server is serving a page over SSL with the HTTP cache-control header set to "no-cache, no-store". I was expecting the "view source" command to be greyed out in this circumstance (as it is on another machine). But it works. When I "view source", I get an entry in the Temporary Internet Files folder with an "internet address" property of "view-source:https://myserver/...." and the content of the page. I wasn't expecting that. I can't understand why one machine is different to another in this regard. Obviously there is some environment/setup difference, but I can't track it down. Anyone have any bright ideas?

  Read the article

< Previous Page | 503 504 505 506 507 508 509 510 511 512 513 514  | Next Page >