Search Results

Search found 17501 results on 701 pages for 'stored functions'.

Page 521/701 | < Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• Macros in Excel 2010 hangs

  - by Ahmad

  I have a spreadsheet with several macros. Generally, when previously using Excel 2007, a user clicks a button and everything works as expected (calculations, some email sending & file I/O). Typically, the expected run-time is about 90 seconds. The spreadsheet is a xlsm file created with Excel 2007. With Excel 2010 however, the same user process results in a non-responsive excel and forces us to kill excel from the task manager. Some note that I have gathered so far in trying to debug this issue: When monitoring CPU usage, it seems that Excel does start the macro. CPU usage increases as expected to about 47% for a few seconds. Excel.exe than drops to 0% usage and I now have a non-responsive Excel (even after 1 hour). If I set debug break points across modules and different functions and step through the code (after clicking the button) , the process works as expected albeit much slower. To add, there were no exceptions. I am at a complete loss as to what the issue may be. I initially thought it may be the add in that is being used but that was debunked by point 2. This seems to be a very odd situation. I can provide more information if required, but I'm at wits end about the root cause could be. I need help in diagnosing and resolving this issue.

  Read the article

• How is made sure magnetic or electric fields from devices like transformers or fans close nearby do

  - by matnagel

  Fans and transformers which are inside the server case create magnetic and electric fields. Electric fields can be easily shielded, but what about magnetic fields, they can only be shielded with high cost materials like mu metal http://en.wikipedia.org/wiki/Mu-metal If a hard drive is installed too close to an intense transformer field, how is the magnetically stored information on the ferromagnetic surfaces of the disk kept safe? Even if drives are shielded, where are the limits? Is there some technical investigation or recommendation from manufacturers about this? (I never heard about something and never had any problem but I am interested in some facts. This is much preferred over what you believe or a habit you developed. Please try to give some solid infromation.) I have built and repaired many servers and sometimes I did put the harddrive on top of the power supply. Edit: This question is not about frequencies that could affect the drive via the power or data connectors of the drive, those are electronically decoupled and that's another question. Edit 2: The wikipedia page states that the motor inside the drive is shielded with mu metal. It is obvious that manufactureres have to take care of this. This question is about such influences from outside the drive.

  Read the article

• How can I store logs and meet compliance requirements for free?

  - by Martin

  I am trying to keep long-term logs of an app in such a way, that it could plausibly demonstrated to third parties/court that the application has processed certain data at a given time. The data can be represented in XML or text format. A simple gzipped log is not plausible, as I may have added or modified data afterwards, whereas an external logging service would be an overkill. Cost is an issue, we are not dealing with financial data or so, but rather some simple user generated content, where some malicious users tried to blame the operator in the past when things escalated and went to court. My question: Is there some kind of signing software for Linux that signs each element of a log in such a way, that it can be easily shown that no element can be added or modified afterwards? Plug-Ins into some free Splunk Alternatives would be fine too. Ideally the software I am looking for should be under a GPL or similar license. I could probably achive something like this by using PGP/GPG sgning functions and including the previous elements signituares within the following element, but I would prefer to use some program where you do not have to argue about the validity of your own code. Note to mods: I am not asking this question on Stackoverflow, because I am not looking for writing own code for reasons described above. I think this question rather fits into serverfault than superuser, as server-side logging software is discussed rather here than on superuser.

  Read the article

• setting up tracd behind mod_proxy?

  - by FilmJ

  I'm having trouble setting up mod_proxy and tracd. Seems almost all the search results for this problem take me to the built-in trac documentation page that mentions it as an option. I have several VirtualServers already running on the box in question, so running tracd on port 80 or 443 is not an option, but I do want to make my trac server accessible on this machine without exposing an additional port via the firewall. Making things even more complicated is that I have multiple trac repositories being served by the same instance of tracd, and so I want to set it up so: http://trac.abc.com is proxy'd to localhost:8000/projects/abcproject, and http://trac.def.com is proxy'd to localhost:8000/projects/defproject. Currently, the setup I have below results in 100% 403 errors. The server is running as www-data and the directory where all trac files are stored is owned by www-data, AND tracd (as show below) is running as www-data, so not sure where it's getting hung up. The relevant configuration on /var/apache2/sites-enabled/trac.abc.com: ProxyPass / http://localhost:8000/abcproject ProxyPassReverse / http://localhost:8000/abcproject The relevant configuration on /var/apache2/sites-enabled/trac.def.com: ProxyPass / http://localhost:8000/defproject ProxyPassReverse / http://localhost:8000/defproject The command used to instantiate tracd: tracd -a defproject,/var/www/vhosts/trac-common/users.htdigest,DEFProject -a abcproject,/var/www/vhosts/trac-common/users.htdigest,ABCProject -p 8000 -b localhost -e /var/www/vhosts/trac-common/projects If I access the site at http://localhost:8000/ everything works fine, but if I try to access via any of the proxy'd hosts I end up with 403 at every turn. I've used mod_proxy successfully as described above for other servers, such as couchdb, so maybe this has to do with the headers sent by tracd??

  Read the article

• saving and searching encrypted mail

  - by student

  I often send and receive gpg-encrypted mail. At the moment I use thunderbird + enigmail (in linux) to do that. As far as I know there is no way in thunderbird to find all encrypted messages which bodies contain particular keywords. There also seems to be no option to save encrypted mails decrypted (so they would be searchable). However for me it is important to be able to search old encrypted mails. So my question is: Is there a way in linux to save incoming mails automatically decrypted in my inbox and save outgoing encrypted mail decrypted in the send folder? Both times adding a line to the body which remarks that the mail was encrypted. It could be another email client for linux that could to that or perhaps a solution using procmail or maildrop. For a procmail solution I guess there could be some problems with encoding (perhaps one have to use emil?) the solution should work well with german special characters in subject and body. Note that the solution should work for multipart encrypted messages (including encrypted attachments) too i.e. with everything which could thunderbird + enigmail generate. Further note that I don't want a discussion about security holes. For me it's ok if messages are stored decrypted on my harddrive (which is encrypted as a whole anyway). In doubt for a first solution it would be ok to store my private key passphrase in cleartext on my harddrive, too. The point is that the mails are encrypted on the mailserver or more generally on their "way through the net".

  Read the article

• How to record tv to network share with Windows Media Center?

  - by Peterdk

  Well, you would think that Windows 7's new MediaCenter would be up to the task of recording your TV to a network share/drive. Too bad, it looks like it's just not possible. I have a windows 2008 R2 server, and a Windows 7 machine with a TV card. Since my server has 2TB of storage, it would be nice to record directly to it's networked drive. (I mounted it as Z:). I tried the following: Selecting it in Media Center Itself: Not working. Not available. Editing the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Service\Recording , setting RecordPath to Z:\TV. Not working. Editing the registry: setting RecordPath to \\server\TV. Not working. Creating a Symlink (mklink \D) to Z:\TV and \\server\TV and setting that in the registry as RecordPath. Currently I am out of options. I could ofcourse Install Windows7 on my server, but I have no license for that, and my windows 2008 r2 is free from dreamspark. Are there people that are succesfully recording to a networked drive/storage? edit I also need to mention that I need to be able to acces the stored files from other PC's, like my laptop. So iSCSI is great for recording, but it looks like you can't access iSCSI devices from multiple PC's. Looks like sharing a iSCSI device is out of the question, so: Are there workarounds to get this thing recording to my network drive?

  Read the article

• effective back-up using Raid / Win7 back-up

  - by Job

  I have a stand-alone pc system with two 2 tb harddiscs, one of which configured as Raid1, i.e. mirorring. The operational drive is partitioned. I use an external 1 tb harddisc for back-up using Windows 7 back-up facility which will be swapped weekly and stored on other premises. I back-up all partitions AND allow a system back-up. All application software is on the C: partition. Questions: How can I see whether Raid1 is working; i.e. is doing its job. All I see now is a status message in the start-up procedure that says its status is normal. How can I see used or available space on Raid 1? The Win-7 backup allows for 1 schedule only as far as I can see. I want daily back-ups of data. However due to the single schedule I am forced to do the time-consuming system back-up and c: back-up as well. Is there a way to activate two schedules allowing a frequent (daily) data back-up and a system back-up with c: drive back-up on a say weekly basis? Of course it can be forced by hand but I am likely to forget that. I am not the programming type of person so looking for simple and controllable solutions. Thank you - any help is apreciated.

  Read the article

• How to pin "Visual Studio 2010 Documentation" shortcut to Windows 7 taskbar?

  - by Chris W. Rea

  I just installed Microsoft Visual Studio 2010 at home, on my Windows 7 PC. One of the items installed with VS2010 is "Microsoft Visual Studio 2010 Documentation". I like to have the documentation installed locally and at my fingertips, and so before had always added a shortcut for the help viewer to my Quick Launch toolbar. However, I'm not able to pin the new documentation to the Windows 7 taskbar. It's frustrating. Note carefully: When I launch "Microsoft Visual Studio 2010 Documentation" from the Start menu, it seems to perform two functions: First, it launches the "Help Library Agent", which is a local HTTP server from which the help content is served... similar to the local ASP.NET web development server. Second, it launches the default web browser against the localhost URL corresponding to the port on which the "Help Library Agent" is running, for example: http://127.0.0.1:47873/help/1-1444/ms.help?method=f1&query=msdnstart&product=VS&productVersion=100&locale=en-US ... in other words, the program doesn't leave behind an active foreground process that displays in the taskbar. So, I can't choose "Pin this program to taskbar" as one might do so with a typical program. How can I get a shortcut to "Microsoft Visual Studio 2010 Documentation" in the Windows 7 taskbar? Has anybody got a workaround for this?

  Read the article

• Is there a list of Windows services that can be turned off to save resources?

  - by scunliffe

  Every time I open up my task manager and look at the tasks running, it appears to me that there has got to be a bunch of junk running in there that I don't want or need and would be better off turning off (e.g. set the service to manual vs. automatic) In particular I'm running Windows XP, but I'd be interested in services for any version. e.g. Service: ThinkPad PM Service What is it: The ibmpmsvc.exe process is installed by default on IBM Notebook computers. It allows various functions of your IBM notebook to be controlled using the blue Fn keys. If you use the blue Fn keys on your Notebook, you should leave this process running. Otherwise, if it is causing problems for your system you should terminate the ibmpmsvc.exe process. (source) Thus for me, (having never used, or intending to use these buttons) - I want to turn it off. There's lots that just seem painfully unnecessary to me... I'm just not sure which ones I can "safely" stop/disable without issues... "Alerter", "ClipBook", "Messenger", "Telnet", "ATI Hotkey Poller", "Office Source Engine", etc. I'd appreciate any info on services that are truly unnecessary, or only useful to certain people/types of users.

  Read the article

• Get Safari to use different autocompletion on different URLs on same hostname

  - by Luke404

  I have a webserver publishing different services over the same SSL VirtualHost, the two most commonly used being PhpMyAdmin and Cacti. These (and others) use 'cookie' style authentication, asking user and password in an HTML form (thus not using HTTP Authentication). Being on the same hostname, the Safari browser didn't manage too well stored passwords: if I login to one app with user foo, and then go to app two it would propose me user foo and its password in the login form. Changing just the username to bar used to be sufficient to let Safari autocomplete the correct password in its form field. Annoying, but I could live with it - usernames are short and easy to remember when compared to the passwords we use. After the update to safari5 this seems to be no longer true: if I store in safari (actually user keychain on OSX) credentials for https://www.foobarbaz.com/app1 AND credentials for https://www.foobarbaz.com/app2 there seem to be no way for it to autocomplete both based on the url. Even editing the keychain to add the path (it will store only the hostname by default) does not help. Is there anything I can do to let it work the way I want while still keeping everything on one hostname? Modifying anything server side is of course possible, but I can't switch apps to HTTP Auth (and not every one will support it anyway) to use different 'realms'.

  Read the article

• How do I configure VMware View location-based printing to use Active Directory Groups?

  - by Jason Pearce

  I am attempting to configure VMware View 4.5's Location-Based Printing, which leverages an included OEM version of ThinPrint, to assign printers to active directory groups. The location-based printing feature maps printers that are physically near client systems to VMware View desktops. I am using the Active Directory group policy setting AutoConnect Location-based Printing for VMware View, which is located in the Microsoft Group Policy Object Editor in the Software Settings folder under Computer Configuration. The AutoConnect Location-based Printing for VMware View appearst to be just a name translation table. It permits me to assign a specific printer or printers to an IP Range, Client Name, Mac Address, User, or User Group. I'm attempting to assign printers to active directory user groups. I have created a new active directory group for each printer that I intend to use in VMware View desktop pools. I will then assign active directory users to the active directory groups that represent each network printer. Example: doej is a member of the PTR-FLOOR2-NORTH-ROOM255 active directory group. Using AutoConnect, I assigned the group to receive a network printer by adding PTR-FLOOR2-NORTH-ROOM255 in the User/Group column. Problem: When doej logs in to his VDI session, the printer is not present. However, if I use a wildcard "*" in the User/Group column instead of the specific PTR-FLOOR2-NORTH-ROOM255 active directory group, the printer is present and functions as designed. Alternatives: I have tried assigning printers to active directory groups within AutoConnect in the following ways, all unsuccesfull: PTR-FLOOR2-NORTH-ROOM255 domainexample\PTR-FLOOR2-NORTH-ROOM255 domainexample.local\PTR-FLOOR2-NORTH-ROOM255 Confirmation: The information used to map the printer to the VMware View desktop is stored in a registry entry on the View desktop in HKEY_LOCAL_MACHINE\SOFTWARE\Policies\thinprint\tpautoconnect. For each of these examples, I have reviewed the registry entry and can confirm that the desktop is receiving the information from the AutoConnect translation table. Summary: Can anyone provide an example of how to configure VMware View 4.5's Location-Based Printing so that I may assign network printers to active directory groups via the included AutoConnect tool? I would welcome a clear example of a working configuration. Thank you.

  Read the article

• Good Enough Failover Strategy for DNS / MySQL / Email

  - by IMB

  I've asked and read a lot questions regarding DNS failover but the more I read the more complicated it becomes, some people say it's good enough some say it isn't. No clear answers from what I read. I was wondering if we can set it straight once and for all, at least for the requirements of most websites out there. Right now let's assume the following: We don't need really need load-balancing, what we need is a failover solution. We are running a website based on LAMP on a VPS. We need to make sure that the Web Server, MySQL, Email are always accessible if not 99%. Basically here's my idea and questions about it: Web Server: We need at least one failover server (another VPS on a separate data center). Is DNS Failover via Round Robin good, if not, what's the best? And how do you exactly implement it? How do you make the files you upload/delete on Server A is also on Server B? MySQL: I've only read a brief intro to MySQL replication and I assume that I can replicate Server A to Server B and vice versa on the fly right? So just it case Server A fails and Server B is now running, it will continue to work and replicate to Server A when it becomes available. So in essence Server B is now the primary server, and will later on failover to Server A, should a failure happen again. Email: If we are gonna use DNS Failover, using webmail or relying on emails stored on the server is probably not a good idea right? Since some emails might be on Server A while some might be on Server B? I assume a basic email forwarder to a 3rdparty is good enough (like Gmail for example) to ensure all emails are kept in one place. Here's a basic diagram for a better picture: http://i.stack.imgur.com/KWSIi.png

  Read the article

• Ubuntu "No space left on device" for /home, df shows 100% full, ds shows much, much less

  - by Jon Cram

  On an Ubuntu 12.04 server, normal users can no longer create or add to files in /home, encountering a "No space left on device" error. The /home directory has a capacity of 1.7 terabytes and as far as I can tell is nowhere near full in terms of actual data stored or inodes used. df -h shows: Filesystem Size Used Avail Use% Mounted on /dev/md2 1.0T 18G 955G 2% / udev 7.7G 4.0K 7.7G 1% /dev tmpfs 3.1G 320K 3.1G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.7G 0 7.7G 0% /run/shm cgroup 7.7G 0 7.7G 0% /sys/fs/cgroup /dev/md3 1.7T 1.7T 0 100% /home /dev/md1 496M 45M 426M 10% /boot /home indeed looks rather full. du -hs /home suggests otherwise: 1.4G /home There appears no inode issue - df -i: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/md2 67108864 75334 67033530 1% / udev 2013497 527 2012970 1% /dev tmpfs 2015816 440 2015376 1% /run none 2015816 2 2015814 1% /run/lock none 2015816 1 2015815 1% /run/shm cgroup 2015816 9 2015807 1% /sys/fs/cgroup /dev/md3 113909760 105981 113803779 1% /home /dev/md1 131072 239 130833 1% /boot I recently deleted a many gigabytes of application cache and log data from /home, however this was in the tens of gigabytes at best and nowhere near the capcity of /home. Update 1: du -hs --apparent-size /home 1.2G /home du -hs /home 1.4G /home What might be going on here?

  Read the article

• Linux Cups raspberry pi offload processing to server

  - by jaredmsaul

  I am interested in setting up a raspberry pi as the local end of a printing solution. In my testing the pi chokes on acting as a complete cups based print server. It seems a little underpowered for some of the ghostscipt processing and other filtering that occurs-- particularly on larger or complex documents the processing time can be 5 or more minutes. My question is can the processing be largely done elsewhere and the prepared end product of the processing chain be fed to the pi for output on the connected printer? So in this scenario any arbitrary document (html, pdf, text) is initially 'printed' on a relatively powerful machine but the output is stored in a file. This file is then grabbed by the pi and with all the heavy work out of the way easily printed using cups. I know files can be pushed through cups in raw mode but I am fuzzy on the pros and cons and the applicability in what I describe. I have tested this with pdftops creating a ps file then feeding that raw to cups and I think it works but it seems like there may be a cleaner solution. This scenario would ideally work for any number of printer types.

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• DHCPD (Slackware) - Disabling auto-generation of gateway as DNS server

  - by Dogbert

  Good day, I am using a Linux workstation on Slackware 13.37. One "problem" I have had to deal with ever since 11.0 is the following: DNS servers are queried and determined at startup by DHCP daemon (DHCPD) This is invoked at startup by a script located at /etc/rc.d/rc.dhcpd My DNS servers for my ISP are resolved correctly, and are stored in a list located at /etc/resolv.conf However, the one annoying problem is that my gateway IP (ie: 192.168.1.1) is always automatically put at the top of the list in resolv.conf, meaning I have to always wait for a timeout before a valid DNS server is used to resolve an address (ie: timeout on 192.168.1.1 because it is not actually a DNS server, then DHCP uses the next server in the list). I could lower my DNS resolution timeout so the gateway query times out quicker, but that's not what I want, as I don't want to degrade the abilities of legitimate DNS servers. What I would like to do is change how DHCPD operates so that it does NOT put my gateway IP address at the beginning of this list. I've searched via "man dhcpd", etc, and haven't found the exact answer yet. Any help on this issue is appreciated. Thank you all in advance for your time and assistance.

  Read the article

• How to remove NTFS system files from a previous Vista installation

  - by Boldewyn

  I'm trying to shrink my system partition under Win Vista. It's all fine, except that in front of the last 300MB of the volume sits a single file, that cannot be moved by defrag or other means from its position. It's called C:\$Extend\$UsnJrnl:$J, and my assumtion is, that it is left from a previous installation of Vista, when I re-set up the system. Now, googling for this kind of files brings interesting results, but no solution to my problem: Files left on the disk can become ownerless in a new setup of Windows and inaccessible (even for administrators). To be able to access them again, I found the tip to use takeown to re-assign them to the Admin group (or anyone else). Works like a charm for normal files, but not for the C:\$Extend stuff. The C:\$Extend folder is a system folder of the NTFS file system, where the journal is stored (especially in a file called $UsnJrnl:$Data, whose name is surprisingly close to mine). You can delete the journal with fsutil usn /delete C:, however, this doesn't work from within the booted system (as I found out trying). Also, I'm not quite sure of the side effects. You can't move the NTFS own files with standard defrag tools. The same holds, by the way, for not accessible files. Every bit of knowledge out there is targeted to either not accessible files or the $Extend NTFS stuff, but noone addresses my problem involving both, an inaccessible system file. Question: How can I remove this file, or at least how can I move it on the disk?

  Read the article

• What is causing ocassional white windows on my Mac?

  - by user63333

  Hello. I'm having a very strange problem with my Mac lately. When I'm working in an app and a new window pane or sheet is displayed, sometimes it comes up completely white. Once an app is having these problems, it will continue to bring up a blank screen for that particular window (although other windows work fine). After the app is relaunched, the window is fine again. What I'm noticing that's very strange is that although the interface turns completely white, the functions of the interface are still available. So I have to "navigate blindly" around the interface, until I can relaunch. This occurs throughout the operating system. Screenshots: This is what happened when I tried opening the File menu in Lightroom app. What happened to me on Lynda.com (in Firefox) after selecting the "Software..." dropdown. (All other dropdowns were fine. Reloading the page fixed it.) When I was decompressing a file, The Unarchiver launched and opened this white window. It still decompressed the file. This is what happened one time when I opened Finder (with TotalFinder) to my Downloads folder. This is something I've never seen before. This just started happening lately. What could be the problem? Thanks for your help. NOTE: since new users are not allowed to post images, just image blank white interface elements. And since new users also aren't allowed to post more than one link, here's the first screenshot:

  Read the article

• Accessing clearcase view drive from virtual machine is slow

  - by PermanentGuest

  I have a windows XP virtual machine running under a Windows XP host. On the host : On the host clearcase 7.1.1.2 is installed. I have a dynamic view mapped onto some drive. The view has certain VOB/directory structure where my application DLLs from the nightly build and config files are stored. I run my application on the host machine which uses the DLLs and config files from the VOB and everything runs smooth. Now I want to move this set-up to a virtual machine. On the guest : I'm running the guest with a vm-player. I don't want to install clear-case on this as I don't want to expose this machine onto the network. The network setting in the guest is 'host-only'. I have mapped the host's clearcase view drive as a shared folder and I'm able to access this drive from the virtual machine. Also, the application is running. However, the problem is that the access of the clearcase drive from the virtual machine is very slow. I can experience this from the windows explorer. Due to this, the starting of my application takes several seconds in the virtual machine while on the guest it comes up pretty fast. My question is : Is there any way to speed up the performance? I have managed to copy some of the DLLs which don't change frequently to the virtual machine to improve the performance. However, there are still lot of DLLs which have to be taken from the clearcase drive as they change frequently. VMplayer version is : VM Player 3.0.1 build-227600 Both guest and host is : Windows XP service pack 3 Host clearcase is : clearcase 7.1.1.2

  Read the article

• The best way to hide data Encryption,Connection,Hardware

  - by Tico Raaphorst

  So to say, if i have a VPS which i own now, and i wanted to make the most secure and stable system that i can make. How would i do that? Just to try: I installed debian 7 with LVM Encryption via installation: You get the 2 partitions a /boot and a encrypted partition. When booting you will be prompted to fill in the password to unlock the encryption of the encrypted partition, Which then will have more partitions like /home /usr and swapspace which will automatically mount. Now, i do need to fill in the password over a VNC-SSL connection via the control panel website of the VPS hoster, so they can see my disk encryption password if they wanted to, they have the option if they wanted to look at what i have as data right? Data encryption on VPS , Is it possible to have a 100% secure virtual private server? So lets say i have my server and it is sitting well locked next to me, with the following examples covered bios (you have to replace bios) raid (you have to unlock raid-config) disk (you have to unlock disk encryption) filelike-zip-tar (files are stored in encrypted archives) which are in some other crypted file mounted as partition (archives mounted as partitions) all on the same system So it will be slow but it would be extremely difficult to crack the encryption. So to say if you stole the server. Then i only need to make the connection like ssh safer with single use passwords, block all incoming and outgoing connections but give one "exception" for myself. And maybe one for if i somehow lose my identity for the "exeption" What other overkill but realistic security options are available, i have heard about SElinux?

  Read the article

• Write permissions on uploaded files - Linux, Apache, PHP

  - by letseatfood

  I am working on a PHP script that transfers files using FTP functions. It has always worked on my production server (which is a hosting service). The development server I have just setup (I am a novice to servers) is Debian Lenny with Apache2, PHP5, and MySQL5. The file transfer works correctly, but once the file has been written to the server, it has permissions of 600. This makes it impossible for me to view the file (JPEG) in the web browser, as permission is denied. I have scoured the internet and even broken my server installation and reinstalled it trying to figure this out (which has been fun, nonetheless!). I know it is unwise to set 777 permissions on public accessible files, but even that will not solve the problem. The only thing that works is if I chmod 777 thefile.jpg after it has been transferred, which is not a working solution. I tried changing the owner of my site files to www-data per this post, but that also does not work. My user is mike, and it still does not work whether the owner of the files is mike or root. Would somebody point me in the right direction? Thanks! And, of course, let me know if I can clarify anything.

  Read the article

• How do I restore tab-completion on shell variables on the bash command-line?

  - by Eric

  I've long set my most-recently visited directories to shell variables d1, d2, etc. On an ancient Fedora machine I could type a command like $ cp $d1/ and the shell would replace $d1 with text like /home/acctname/projects/blog/ and would then show me the contents of .../blog, like any tab-completion. Now, both ubuntu wheezy/sid and fedora 16 just -escape the '$', and naturally there are no completions to show. You can see this behavior in action in an OSX Terminal window. On 10.8, do something like ls $HOME/ to see what I mean. Is there a bash shell variable or option that can restore the old behavior? man bash suggests this is a bug: complete (TAB) Attempt to perform completion on the text before point. Bash attempts completion treating the text as a variable (if the text begins with $), username (if the text begins with ~), hostname (if the text begins with @), or command (including aliases and functions) in turn. If none of these produces a match, filename completion is attempted. I get the above described completion when a token starts with '~' or a letter. It's just '$'-completion that's broken.

  Read the article

• Scripting a permanent CTRL / CAPS swap in Gnome?

  - by Duncan Bayne

  I have a bash script that I use to configure a vanilla Ubuntu (10.10 Maverick Meerkat) installation to be exactly the way I want it. I make extensive use of gconftool-2 to configure the desktop, set up shortcut keys, etc. Now, I'm trying to swap the CTRL and CAPS keys. I have found two ways of doing this: In Gnome, go to System - Preferences - Keyboard - Layout - Options and make the change in there. This works well, but I don't know how to script this; the setting doesn't seem to be stored in the usual place as I can't find it with gconf-editor. Add the line setxkbmap -option "ctrl:swapcaps" to my .bashrc file. That works too, until I suspend the machine & then resume it. At that point the CTRL and CAPS behaviour return to normal, until I cause .bashrc to be run again by opening a new shell. This behaviour has been reported as a bug in RedHat. Could someone please suggest a way of switching those keys that is both permanent, and can be scripted? I'm sure I must be missing something obvious here ...

  Read the article

< Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >