Search Results

Search found 41561 results on 1663 pages for 'linux command'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 535/1663 | < Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >

  • Logging violations of rules in limits.conf

    - by PaulDaviesC
    I am trying to log the details of the programs that where failed due to the limit cap defined in the limits.conf. My initial plan was to do it using the audit system. The idea was to track the system calls related to limits in the limits.conf that where failed. However the problem with this approach is that , it is not possible to track the violations of cpu time, since that violation do not involve failure of system calls. In the case of CPU time , one thing happens is that the program which violated the cpu time will be delivered a SIGXCPU. So my question is how should I go about logging the programs that violated CPU time? Also is there any limits.conf specific logs available?

    Read the article

  • How do I stop someone from saturating my line & wasting CPU cycles

    - by JoshRibs
    My web host shows inbound & outbound traffic with mrtg. I have a steady 3.5mbps inbound traffic from Nigeria. Even assuming the source IPs & destination ports are blocked with Iptables & verifying nothing is listening on those ports, will the traffic still always pass through the switch & "get" to my server (where my server wastes CPU cycles "dropping" the packets)? Assuming I was setup with a hardware firewall, the traffic would still show in mrtg assuming the firewall is behind the switch? So is there any way to stop someone from saturating your 100mbps line, if they also have a 100mbps line? Other than filing an abuse complaint with the kind folks in Nigeria?

    Read the article

  • Playing/extracting audio file from PDF

    - by ravl1084
    I use Ubuntu and I have a PDF file that contains an audio annotation. It won't play on Okular, it treats it as a text annotation. Following an old blog post where the poster created a small C script to extract the audio didn't work either, I suspect the format of these audio annotations has changed. Using the information on it I managed to uncompress the PDF and with vim, I found the audio data in the file. I tried copying this into its own file and changed the extension from mp3, wav, mid, but none of them would play. Is there a way of achieving this?

    Read the article

  • MTD mtd3ro backup returns BCH decoding failed

    - by saeed144
    While doing a kernel backup of an mtd (Memory Technology Device) from /dev/mtd/mtd3ro of a TI board gives many "BCH decoding failed", Here are system info #cat /proc/mtd dev: size erasesize name mtd0: 00080000 00020000 "X-Loader" mtd1: 00140000 00020000 "U-Boot" mtd2: 000c0000 00020000 "U-Boot Env" mtd3: 00500000 00020000 "Kernel" mtd4: 1f880000 00020000 "File System" here is the method used, dd if=/dev/mtd/mtd3ro of=/data/local/tmp/mtd3.bin doing a cat also returns the same error, and here is the error, BCH decoding failed BCH decoding failed yes, the destination has enough space ;) tell me what do you think? Thanks

    Read the article

  • Why and when to use Personal Package Archives (PPA)

    - by reversiblean
    Do you prefer PPA over core repositories and why or why not? Are there any compatibility issues when using a PPA as there are different distro releases but just one common repository? Where would you normally search for application repositories that are not in the core repositories? I.e., I was about to install Gnome Flashback in Ubuntu 12.04 which is the new classic version of earlier fallback but found that it's only available as a ppa-release and was wondering which one to choose between the two; fallback or newer flashback.

    Read the article

  • Skip kernel module at boot

    - by Gris
    Hello. There is a broken kernel module, due to which I can not even load the OS, so I can not delete or fix it. Is it possible to skip this module at boot, using the kernel's parameters or something? Thanks.

    Read the article

  • How to remove a tagged block of text in a file?

    - by EmpireJones
    How can I remove all instances of tagged blocks of text in a file with sed, grep, or another program? If I have a file which contains: random text // START TEXT internal text // END TEXT more random // START TEXT asdf // END TEXT text how can I remove all blocks of text within the start/end lines, produce the following? random text more random text

    Read the article

  • I need to somehow change my ip address

    - by tric
    hello. i`m in a lan using iptables/masquerade. what i want to do, is to login in a web application.i write my user and passwd and click login and everything is fine, but if i try to modify something in that aplication it tells me that i have a wrong ip address.i knwo for sure that this app only allows ip 10.3.x.x .how can i trick that application to think that i have an ip from class 10.3.x.x and not my wan ip? 10x sorry for my bad english!

    Read the article

  • NIC is receiving, but not transmitting at all?

    - by Shtééf
    I'm trying to fix a very strange problem remotely on a machine at a customer site. The machine is a Dell PowerEdge, I believe a 1950 (haven't verified, but the lspci output matches specs I found.) The machine has two similar NICs, identified as Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) by lspci, and using the bnx2 driver. (I suspect these are on-board and on the same controller, which is what I'm accustomed to for this type of machine.) The primary interface eth0 works perfectly, and is in fact how I am ssh'd in. However, the secondary interface eth1 is not transmitting. I can see this in ifconfig output, for example, where the TX field is always 0. However, it is receiving, and tcpdump shows ARP requests coming from the ISP's gateway on the other side. The interface is physically connected to a Siemens BSTU4 modem, configured by the ISP. The link is properly set to 10MBps and full duplex, without negotation, as the ISP requested. A small /30 subnet is configured. For the sake of anonimity, let's say the machine is 3.3.3.2/30, and the ISP's gateway .1. The machine has no firewall settings whatsoever. Even running something like arping -I eth1 3.3.3.1, and running tcpdump alongside, shows no traffic whatsoever being transmitted on the interface. (But the other side keeps steadily sending ARP requests, and that is all that can be seen.) What could be causing this? Here's some output, anonymized, which may hopefully help: $ ethtool eth1 Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off Supports Wake-on: d Wake-on: d Link detected: yes $ ip link show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:15:c5:xx:xx:xx brd ff:ff:ff:ff:ff:ff $ ip -4 addr show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 inet 3.3.3.2/30 brd 3.3.3.3 scope global eth1 $ ip -4 route show match 3.3.3.0/30 3.3.3.0/30 dev eth1 proto kernel scope link src 3.3.3.2 default via 10.0.0.5 dev eth0

    Read the article

  • How do you backup your own files? [on hold]

    - by Antonis Christofides
    I'm a system administrator and I use rsnapshot to backup some servers, duplicity for some others. Both work fine, each one with advantages and disadvantages. Despite that, I am at a loss on how to backup my own private files. I'd use duplicity to automatically backup my files to a remote server; but the problem is that once in a while I must do a full backup. My emails and important files are 9G, and I expect this to increase. Uploading through aDSL at 1Mbit would be 20 hours. Too much. rsnapshot doesn't require periodic full backups (only the first time), but it must be running on the remote server and have a means to connect to my computer; if the server is compromised (or simply if the NSA decides to use it), my own machine is also compromised. Not good. The only solution I've come up with is use encfs, use unison to synchronize the files to a remote server, and use duplicity or rsnapshot on the remote server to backup these files. In that case, the question is whether I can sync the files on many computers; is it possible for encfs to be used with the same key on many computers? I also think that if I append one character to the unencrypted file, its encrypted encfs counterpart might change a lot, so that incrementals with duplicity would be less efficient—but not a big deal. Maybe also, when I need to restore a file, finding the correct file to restore could be a pain, because of filename encryption. I wonder whether there is any other possibility that I've overlooked. Maybe I'm asking too much for my personal use, and I should settle with an external disk?

    Read the article

  • Setting umask for all users

    - by Yarin
    I'm trying to set the default umask to 002 for all users including root on my CentOS box. According to this and other answers, this can be achieved by editing /etc/profile. However the comments at the top of that file say: It's NOT a good idea to change this file unless you know what you are doing. It's much better to create a custom.sh shell script in /etc/profile.d/ to make custom changes to your environment, as this will prevent the need for merging in future updates. So I went ahead and created the following file: /etc/profile.d/myapp.sh with the single line: umask 002 Now, when I create a file logged in as root, the file is born with 664 permissions, the way I had hoped. But files created by my Apache wsgi application, or files created with sudo, still default to 644 permissions... $ touch newfile (as root): Result = 664 (Works) $ sudo touch newfile: Result = 644 (Doesn't work) Files created by Apache wsgi app: Result = 644 (Doesn't work) Files created by Python's RotatingFileHandler: Result = 644 (Doesn't work) Why is this happening, and how can I ensure 664 file permissions system wide, no matter what creates the file? UPDATE: I ended up finding a cleaner solution to this on a per-directory basis using ACLs, which I describe here.

    Read the article

  • check_ssh executed from Nagios server returns "Server answer: ", nothing else

    - by phs
    Commmand works on the host I need to monitor (its IP is denoted as $HOSTADDRESS$ here): [root@host ~]# /usr/local/nagios/libexec/check_ssh localhost SSH OK - OpenSSH_4.3 (protocol 2.0) However, on the Nagios server, it does not: root@server:~# /usr/lib/nagios/plugins/check_ssh -H $HOSTADDRESS$ Server answer: I can see that the port is open: root@server:~# /usr/lib/nagios/plugins/check_tcp -H $HOSTADDRESS$ -p 22 TCP OK - 0.123 second response time on port 22|time=0.123277s;;;0.000000;10.000000 And I can verify with telnet: root@server:/etc/nagios3/conf.d# telnet $HOSTADDRESS$ 22 Trying $HOSTADDRESS$... Connected to $HOSTADDRESS$. Escape character is '^]'. After searching the web for two hours and trying different suggestions I am out of ideas. I have several other hosts with similar setup, and they don't have this problem. I have compared the configs and they look the same (I think). I am clearly missing something here.

    Read the article

  • volume group disappeared after xfs_check run

    - by John P
    EDIT** I have a volume group consisting of 5 RAID1 devices grouped together into a lvm and formatted with xfs. The 5th RAID device lost its RAID config (cat /proc/mdstat does not show anything). The two drives are still present (sdj and sdk), but they have no partitions. The LVM appeared to be happily using sdj up until recently. (doing a pvscan showed the first 4 RAID1 devices + /dev/sdj) I removed the LVM from the fstab, rebooted, then ran xfs_check on the LV. It ran for about half an hour, then stopped with an error. I tried rebooting again, and this time when it came up, the logical volume was no longer there. It is now looking for /dev/md5, which is gone (though it had been using /dev/sdj earlier). /dev/sdj was having read errors, but after replacing the SATA cable, those went away, so the drive appears to be fine for now. Can I modify the /etc/lvm/backup/dedvol, change the device to /dev/sdj and do a vgcfgrestore? I could try doing a pvcreate --uuid KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ /dev/sdj to make it recognize it, but I'm afraid that would erase the data on the drive UPDATE: just changing the pv to point to /dev/sdj did not work vgcfgrestore --file /etc/lvm/backup/dedvol dedvol Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Cannot restore Volume Group dedvol with 1 PVs marked as missing. Restore failed. pvscan /dev/sdj: read failed after 0 of 4096 at 0: Input/output error Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. PV /dev/sdd2 VG VolGroup00 lvm2 [74.41 GB / 0 free] PV /dev/md2 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md3 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md0 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md4 VG dedvol lvm2 [931.51 GB / 0 free] PV unknown device VG dedvol lvm2 [1.82 TB / 63.05 GB free] Total: 6 [5.53 TB] / in use: 6 [5.53 TB] / in no VG: 0 [0 ] vgscan Reading all physical volumes. This may take a while... /dev/sdj: read failed after 0 of 4096 at 0: Input/output error /dev/sdj: read failed after 0 of 4096 at 2000398843904: Input/output error Found volume group "VolGroup00" using metadata type lvm2 Found volume group "dedvol" using metadata type lvm2 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 5 Metadata Sequence No 10 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 5 Act PV 5 VG Size 5.46 TB PE Size 4.00 MB Total PE 1430796 Alloc PE / Size 1414656 / 5.40 TB Free PE / Size 16140 / 63.05 GB VG UUID o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246 dedvol { id = "o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246" seqno = 10 status = ["RESIZEABLE", "READ", "WRITE"] flags = [] extent_size = 8192 # 4 Megabytes max_lv = 0 max_pv = 0 physical_volumes { pv0 { id = "Msiee7-Zovu-VSJ3-Y2hR-uBVd-6PaT-Ho9v95" device = "/dev/md2" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv1 { id = "ZittCN-0x6L-cOsW-v1v4-atVN-fEWF-e3lqUe" device = "/dev/md3" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv2 { id = "NRNo0w-kgGr-dUxA-mWnl-bU5v-Wld0-XeKVLD" device = "/dev/md0" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv3 { id = "2EfLFr-JcRe-MusW-mfAs-WCct-u4iV-W0pmG3" device = "/dev/md4" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv4 { id = "KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ" device = "/dev/md5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 3907028992 # 1.81935 Terabytes pe_start = 384 pe_count = 476932 # 1.81935 Terabytes } }

    Read the article

  • How to search a text file for strings between two tokens in Ubuntu terminal and save the output?

    - by Blue
    How can I search a text file for this pattern in Ubuntu terminal and save the output as a text file? I'm looking for everything between the string "abc" and the string "cde" in a long list of data. For example: blah blah abc fkdljgn cde blah blah blah blah blah blah abc skdjfn cde blah In the example above I would be looking for an output such as this: fkdljgn skdjfn It is important that I can also save the data output as a text file. Can I use grep or agrep and if so, what is the format?

    Read the article

  • why won't php 5.3.3 compile libphp5.so on redhat ent

    - by spatel
    I'm trying to upgrade to php 5.3.3 from php 5.2.13. However, the apache module, libphp5.so will not be compiled. Below is a output I got along with the configure options I used. The configure statement is a reduced version of what I normally use. ========== './configure' '--disable-debug' '--disable-rpath' '--with-apxs2=/usr/local/apache2/bin/apxs' ... ** ** ** Warning: inter-library dependencies are not known to be supported. ** ** ** All declared inter-library dependencies are being dropped. ** ** ** Warning: libtool could not satisfy all declared inter-library ** ** ** dependencies of module libphp5. Therefore, libtool will create ** ** ** a static module, that should work as long as the dlopening ** ** ** application is linked with the -dlopen flag. copying selected object files to avoid basename conflicts... Generating phar.php Generating phar.phar PEAR package PHP_Archive not installed: generated phar will require PHP's phar extension be enabled. clicommand.inc pharcommand.inc directorytreeiterator.inc directorygraphiterator.inc invertedregexiterator.inc phar.inc Build complete. Don't forget to run 'make test'. ============= php 5.2.13 recompiles just fine so something is up with 5.3.3. Any help would be greatly appreciated!!

    Read the article

  • How do I stop ssh-agent from forgetting my password after I login to the screen session from SSH?

    - by Shwouchk
    I have a screen session open in an lxterminal window. If I SSH somewhere, the first time it happens, an ssh-agent window opens and asks me for my private key passphrase, and after that ssh goes right on. If I log in from outside to this machine and attach to the screen session however, ssh-agent now asks me every time I connect for my passphrase, in the terminal. Is there a way to avoid this and to let it continue using the X agent, or at least to have the non-X agent remember the passphrase?

    Read the article

  • Tuning MySQL to consume less memory

    - by Alex
    I have a VM which has 2GB Ram, (full specs) And I am setting up a site which has one table in particular with over a million records. There's little or no usage of this particular database (perhaps once or twice a day) but simply running mysql grinds the whole server to a halt. I've looked through the top results but nothing is really denting the CPU however the memory seems to be the issue. The site isnt even live of taking requests yet. the memory situation looks like this: # free -m total used free shared buffers cached Mem: 2006 1880 126 0 3 53 -/+ buffers/cache: 1823 183 Swap: 2047 345 1702 Are there any good pointers to tune mysql to stop hogging the system memory? Thanks very much EDIT: (requested by 8bit): http://tny.cz/b41a0b12

    Read the article

  • How to increase acpiphp slots?

    - by Eil
    Hi, Oh RHEL 5.5, there are 31 ACPI PCI hotplug slots by default: acpiphp: Slot [1] registered ... acpiphp: Slot [31] registered Is there a way to increase this number? I haven't been able to find an argument to supply to modprobe, or a sysctl knob to tweak, but I know there must be ways to get more slots based on some Google sleuthing. (For the curious, this is just preliminary experimentation to see how many virtual disks I can hot-add to a running KVM guest.)

    Read the article

  • How does Slackware handle security updates?

    - by Abtin Forouzandeh
    I use a distribution that uses apt for package management and am accustomed to letting apt grab a list of package changes. I generally let it install all the needed security updates. I've been considering migrating to slackware. However, it seems slackware does not have a package management system. How would I learn about new security updates? Is the only way to monitor http://www.slackware.com/security/?

    Read the article

  • Ubuntu IP Configuration - multiple subnets & interfaces

    - by HaydnWVN
    Have a 'new' mailserver running postfix on Ubuntu. We are having some problems configuring the subnets & interfaces. Basically 2 subnets (.253. & .254.) need to be connected through the 3rd subnet (.252.) where the Router is residing. # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.62.254.199 netmask 255.255.0.0 network 10.62.254.0 broadcast 10.62.255.255 #gateway 10.62.252.138 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 10.62.252.138 dns-search ***.com auto eth1 iface eth1 inet static address 10.62.253.199 netmask 255.255.0.0 network 10.62.253.0 broadcast 10.62.255.255 #gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-nameservers 10.62.252.138 dns-search ***.com auto eth2 iface eth2 inet static address 10.62.252.199 netmask 255.255.0.0 network 10.62.252.0 broadcast 10.62.255.255 gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-search ***.com I have an external support company who are looking into this (they built and configured this server), but it's taking far too long... So I'm looking to highlight the mistake!

    Read the article

  • SSH does not allow the use of a key with group readable permissions

    - by scjr
    I have a development git server that deploys to a live server when the live branch is pushed to. Every user has their own login and therefore the post-receive hook which does the live deployment is run under their own user. Because I don't want to have to maintain the users public keys as authorized keys on the remote live server I have made up a set of keys that 'belong's to the git system to add to remote live servers (In the post-receive hook I am using $GIT_SSH to set the private key with the -i option). My problem is that because of all the users might want to deploy to live, the git system's private key has to be at least group readable and SSH really doesn't like this. Here's a sample of the error: XXXX@XXXX /srv/git/identity % ssh -i id_rsa XXXXX@XXXXX @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: UNPROTECTED PRIVATE KEY FILE! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Permissions 0640 for 'id_rsa' are too open. It is required that your private key files are NOT accessible by others. This private key will be ignored. bad permissions: ignore key: id_rsa I've looked around expecting to find something in the way of forcing ssh to just go through with the connection but I've found nothing but people blindly saying that you just shouldn't allow access to anything but a single user.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >