Search Results

Search found 17856 results on 715 pages for 'setup py'.

Page 572/715 | < Previous Page | 568 569 570 571 572 573 574 575 576 577 578 579  | Next Page >

• How do I migrate Exchange 2007 to new hardware?

  - by Graeme Donaldson

  As per my previous question, I have an Exchange 2007 box which is also a DC. Since I can't demote it while Exchange is installed, I want to move Exchange to a different server. Does anyone have any articles, tips or experiences to share on this? The last time I did this it was with Exchange 2003 and even that is a little rusty in my head. The setup is a single Exchange 2007 Hub/Edge/Mailbox/CAS server. Its currently on Windows Server 2008, I can migrate it to the same OS, or I can go to 2008 R2, I'm not really picky on that. We're running OWA/ActiveSync/POP3(S)/IMAP(S) for client access. I already have another fully functional DC/GC/DNS box in the same site and clients in the site are already using that for DNS. It's also the preferred site bridgehead for AD replication. Update: After reading Evan's answer I realised that my original question wasn't worded correctly. I'm not looking to do a swing migration, I actually need to move Exchange completely over to a new box. I have done swing migrations in the past, i.e. moving over to a temporary box and back to the original hardware afterwards, and I'm not really sure why I used that term in the original question since it's not what I intended. Any tips?

  Read the article

• Deploying Windows Service through group policy fails with Event ID 102

  - by Sören Kuklau

  I'm trying to deploy a custom Windows Service (written in C#; installed through a VS setup project) using a group policy. To help debug this, I also have two additional MSIs in the same policy. All three packages are deployed as a machine policy, not a user one. On one machine (runs Windows Server 2008; no UAC), all three deploy fine. The service is set to Automatic, as expected. On two machines (run Windows 7; UAC), the two other MSIs deploy fine, but my service fails to install. The event log gives an event ID of 102, which appears to be a permissions problem: The install of application "Package Name" from policy "Policy Name" failed. The error was The installation source for this product is not available. Verify that the source exists and that you can access it. However, all three packages come from the same share linked through UNC, so this is unlikely. My guess is that UAC is the problem; that the service requires additional permissions. Do I need to alter the MSI somehow?

  Read the article

• Mounting a VirtualBox shared folder on boot with fstab in OpenSuse 11.3

  - by ccook

  I have followed the steps found here, however, the share is not mounted on boot. The share will mount if i run 'mount -a' after booting. Why would the share not mount on boot? 1 - Set up a Virtual Machine and install OpenSUSE 11.2 2 - Create a shared folder on host (HostFolder) 3 - Setup the shared folder in Virtualbox Via the Virtual Machine details or via Devices Shared Folders... 4 - Install dependencies for running the Virtualbox installer You need to install the right development kernelpackage for your machinetype (use 'zypper search -i kernel' to see what's installed) sudo zypper install make gcc kernel-source kernel-hosttype/default-devel 5 - Run the Virtual Machine and go to Devices Guest Additions This mounts an iso image in your OpenSUSE guest. 6 - Open a root terminal and run cd /usr/src/linux make oldconfig && make prepare && make scripts && make dep cp ../linux-obj/$HOSTTYPE/default/Module.symvers . make prepare A commenter on previously mentioned thread says this step is unnecessary but it doesn't work without on my system. I suggest trying step 7 first and returning to step 6 if that fails. * 7 - Run ./VirtualboxLinux yourhosttype .run from the mounted iso image. 8 - Create shared folder in OpenSUSE (GuestFolder) 9 - Test with sudo mount -t vboxsf HostFolder /home/user/GuestFolder It works? Great! Let's set up the system so it automounts for your regular useraccount instead of root-only access. 10 - Add this line to /etc/fstab HostFolder /home/user/GuestFolder vboxsf defaults,uid=1000,gid=1000 0 0 11 - It works for me but if it still doesn't automount after a reboot; sudo mount -a

  Read the article

• Joining Samba to Active Directory with local user authentication

  - by Ansel Pol

  I apologise that this is somewhat incoherent, but hopefully someone will be able to make enough sense of this to understand what I'm trying to achieve and provide pointers. I have a machine with two network interfaces connected to two different networks (one of which it's providing several other services for, such as DNS), running two separate instances of Samba, one bound to each interface. One of the instances is just a workgroup-style setup using share-level authentication, which is all working fine. The problem is that I'm looking to join the other instance to an MS Active Directory domain (provided by MS Windows Small Business Server 2003) to enable a subset of the domain users to access the shares from Windows machines on the other network. The users who need access from the domain environment have accounts (whose names are all-lowercase versions of their domain usernames) on the machine running Samba, but I'm not sure about how to map the UIDs and everything I've read concerns authenticating accounts on that machine against either AD or another LDAP server. To clarify: I only want the credentials for AD users accessing the non-workgroup Samba instance to be authenticated against AD, not the accounts on the machine running Samba. I hope this is sufficiently clear. EDIT: In addition to being able to access the Samba shares from AD, I do also need to be able to access a share on the domain from the machine running Samba but would still like everything non-Samba-related to authenticate locally.

  Read the article

• Home Server: cpu virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on VM (or compute instance) management and what would best suit my needs. (I have another question related to the storage management). My use cases are: A backup server: rsync and other services running. A personal cloud server: a kind of owned dropbox system, à la ownCloud. " users foreseen. A media server: streaming videos and displaying photos. Here my environement and wishes: Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine 2-3 VMs foreseen: backup server, owncloud server and media server (optional). Those are only servers, so no graphical console needed (I don't need VirtualBox) By VM I mean a virtualised environment like KVM, Xen, etc. or a compute instance like with OpenStack storage should be "virtualised/cloudified" see my other question. VM should be able to be migrated to another server in the future if performance cannot be fullfilled anymore by the current server It does not matter if installation of such setup is complicated as long as management tools allow for easy maintenance I don't have Windows at home, so solution should be Linux friendly and would be nice to be web based. But native apps are OK too. System should be easy to enhance: by adding a new server to migate some of the VMs to it. So it's really a kind of private cloud on which I could run some Linux OS. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. So Xen, KVM, VitualBox or OpenStack? What would you recommend?

  Read the article

• Turn off monitor (energy saving) while in text console mode (in Linux)

  - by Denilson Sá

  How to configure Linux text console to automatically turn of the monitor after some time? And by "text console" I mean that thing that you get on ctrl+alt+F[1-6], which is what you get whenever X11 is not running. And, no, I'm not using any framebuffer console (it's a plain, good and old 80x25 text-mode). Many years ago, I was using Slackware Linux, and it used to boot up in text-mode. Then you would manually run startx after the login. Anyway, the main login "screen" was the plain text-mode console, and I remember that the monitor used to turn off (energy saving mode, indicated by a blinking LED) after some time. Now I'm using Gentoo, and I have a similar setup. The machine boots up in text-mode, and only rarely I need to run startx. I say this because this is mostly my personal Linux server, and there is no need to keep X11 running all the time. (which means: I don't want to use GDM/KDM or any other graphical login screen) But now, in this Gentoo text-mode console, the screen goes black after a while, but the monitor does not enter any energy-saving mode (the LED is always lit). Yes, I've waited long enough to verify this. Thus, my question is: how can I configure my current system to behave like the old one? In other words, how to make the text console trigger energy-saving mode of the monitor? (maybe I should (cross-)post this question to http://unix.stackexchange.com/ )

  Read the article

• Possible to host CentOS netinstall files on a local HTTP/FTP?

  - by garlicman

  I'm running XenServer on an Dell R610 and am running into a catch-22. During install from DVD, CentOS can't find the DVD package catalogue. It's a reported error for some, XenServer + CentOS6 + DVD install in some hardware configurations = failed install. Yes, I checked the MD5 and let the disc test pass. In every reported case, the netinstall was the solution. The issue is my net access is required to go through a web proxy that prompts before you can download a file. This naturally breaks any download automation. I've been waiting on our IT to put in an exception rule to allow my lab to bypass the prompt, but it's been over 3 weeks now and they don't seem responsive. (I've been working on this a day or two a week) I want to try and host the netinstall files local in my Xen network. Right now I only have a bunch of Windows based VMs, CentOS won't install so I don't have any Linux tools. I had tried simply hosting all the DVD contents off one of the Windows servers using Mongoose. (I didn't want to setup IIS) I copied them to a hosted sub-directory similar to all the mirrors out there (e.g. http:///centos/6.2/os/i386/) with no auth or anything. Then in the netinstall I correctly pointed to it. I now realize just copying the DVD files over won't work. The repodata will point to a local device, not the site I'm hosting. (e.g. the DVD repodata includes xml that points to where the packages are) Clearly I'm hosting them over HTTP, not from a DVD. Is there an easy way to sort this out? I'm just trying to install CentOS6 on Xen. If there's a turnkey downloadable Xen image with CentOS 6.2 on it, or a downloadable repo image, I'll take that too! Thank you in advance!

  Read the article

• ffmpeg add two audio streams to video

  - by Tossin Hausen

  I tried this: ffmpeg -i /sdcard/video/transcode/video.avi -map 0:0,0 -i /sdcard/video/transcode/first.mp3 -map 1:0,1 -i /sdcard/video/transcode/second.mp3 -map 2:0,2 -acodec copy -vcodec py /sdcard/video/transcode/Output.avi to add two audio streams to one video file. But ffmpeg says the number of mappings should match the number of output streams. What is wrong here? I'm trying to work with an Android build of FFmepg "ffmpeg for android beta". "Does not work" means that this uncommunicative Android build of FFmpeg just stops without giving any error message. The -codec copy option does not work with this build. Now I tried the same set of files with the FFmpeg called command line tool that comes with Ubuntu 10. Something (can't say where it is from). The -codec copy option does not work with this FFmpeg too. Here the complete output: m30x:~/movie/Film$ ffmpeg -i input.avi -i first.mp3 -i second.mp3 -map 0 -map 1 -map 2 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x93cfd10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Input #2, mp3, from 'second.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #2.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Number of stream maps must match number of output streams Merging only one audio stream with the video stream works with Ubuntu and Android version of FFmpeg. Here the complete output: ffmpeg -i input.avi -i first.mp3 -map 0 -map 1 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x9bfad10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Output #0, avi, to 'output.avi': Stream #0.0: Video: mpeg4, yuv420p, 576x432, q=2-31, 90k tbn, 25 tbc Stream #0.1: Audio: libmp3lame, 22050 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #1.0 -> #0.1 Press [q] to stop encoding frame= 6157 fps=6156 q=-1.0 size= 31667kB time=246.28 bitrate=1053.3kbits/s Do you have an idea why it does not work with two audio streams? By the way, ffmpeg -i input_with_first_audio_stream.avi -i second.mp3 -acodec copy -vcodec copy output_two_audio_streams.avi -newaudio works with both versions of ffmpeg that I use, but the first audio stream is played too fast (x10 or more), while the second audio stream is played correct. Many thanks in advance and sorry for my unconventional question and outdated versions of ffmpeg. But I am a lamer and it is not so easy for me to compile from the source (especially for the Android version). I will try to compile an up to date version of ffmpeg with Ubuntu, but I don't have much free time.

  Read the article

• Error setting up Data Protection Manager 2010 Agents / Network "Unauthenticated" in network settings

  - by Bowsa

  I'm not sure if the two are connected but i suspect they are. Basically I'm tring to setup Data Protection Manager 2010 on a fresh install of Server 2008 R2 in a SBS 2003 domain. Everything went fine until trying to install agents across the network. Upon clicking add, i get the following error message: Unable to connect to the Active Directory Domain Services Database. Make sure that the DPM server is a member of a domain and that the controller is running. Also verify that there is network connectivity between the DPM server and the domain controller. ID: 7 As usual (worryingly) the MSDN support for 2010 products is nearly non existant, clicking the error ID simply gives a page not found error. So after 2 days of Googling and trying various fixes (DNS settings, adding permissions to AD objects, rejoining the domain and many more) I thought I'd ask here in the hope that someone out there may have had this issue before. Any help greatly appreciated! Some further info: Firewalls are disabled on the Server 2008, SBS, and client machines. Manually installing and adding the client in also fails, as the DPM server tries to contact the DC first. Edit: I tried creating a new protection group instead, and it gives a different error upon adding the machines: Following machines are not found in AD: COMPUTERNAME.COMPANYNAME.LOCAL Is there a certain directory structure it follows in AD?

  Read the article

• Mac computers unable to connect to samba

  - by tan-ce

  I have a Ubuntu 9 server with samba 3.3 installed. This server has two network interfaces, one to a "public network" which I do not have any control over and another to a private LAN. On the private LAN, samba is the Domain Controller and nmbd is the WINS server on that network. On the "public network", I have configured a second instance of nmbd to run as a WINS client. The setup seems to work fine for Windows XP (on the domain or otherwise) as well as other Ubuntu machines. Finally, my question: Mac computers seem unable to connect to the samba server. As far as I can tell, it is as if samba is invisible to the MAC computer. Could my configuration of nmbd be causing this problem? Or is this simple a Mac oddity and is there anything I can do about it? New updates/info: We tried to connect through the Finder - Connect to Server, we entered smb://servername where servername is the netbios and DNS name. (There is also a DNS entry for the same name on the network) We also tried connecting by IP address Also, I just realized that there is at least one Mac which can connect. (Leopard 10.5.8) I will try to get the Mac OS versions of the computers which couldn't connect as soon as I can. The Mac which could not connect was running Mac OS X 10.4.11. Was there a change to samba on Mac OS between 10.4 and 10.5?

  Read the article

• Samba4/Ubuntu Shares Incorrectly Available to All Users

  - by Dan

  I've got my Ubuntu server working with Samba4 and got it set up as the Primary domain controller on my network with AD and all that goodness. However, I'm trying to get my Samba configuration to work with the users and groups I've defined with the Active Directory tools from Windows. For instance, I've got a share X which I want users A and B (as part of the 'management' group, known as LLGrpManager in my setup) to see, but no body else. However, after making changes to the configuration, restarting Samba, I test by connecting to the share with my Mac over Samba as user 'C' which isn't part of the management group, and I can, incorrectly, see the X share. I've tried alsorts of combinations of specifying the group with no luck at all. I've got a feeling that my global config might be too lenient or something to do with file permissions but being a bit green, I'm without clue. My /etc/samba/smb.conf # Global parameters [global] server role = domain controller server string = Office Server workgroup = LLDOMAIN realm = lldomain.local netbios name = DUMBO passdb backend = samba4 logon path = \\%L\profiles\%U logon drive = L: log file = /var/log/samba/%m.log max log size = 50 security = ads domain logons = yes domain master = auto usershare allow guests = no valid users = %S [netlogon] path = /var/lib/samba/sysvol/lldomain.local/scripts read only = no guest ok = no [sysvol] path = /var/lib/samba/sysvol read only = No guest ok = no valid users = @LLDOMAIN\LLGrpManager [ShareX] path = /data comment = Entire Data Volume guest ok = no comment = Entire Data Volume guest ok = no valid users = @LLDOMAIN\LLGrpManager admin users = @LLDOMAIN\LLGrpManager browsable = no inherit acls = yes inherit permissions = yes ... My /etc/nsswitch.conf I've also instructed the system to use the nss winbind library when searching for users or groups by adding the stanza passwd and group in /etc/nsswitch.conf: passwd: compat winbind group: compat winbind shadow: compat Permissions on the folder in question drwxrwxrwt 8 root root 4.0K Oct 28 19:11 data

  Read the article

• Move an SSD with Windows 7 to a new PCIe SATA controller card

  - by Shevek

  This is my current setup: Abit AB9 QuadGT motherboard which has an Intel P965 chipset with Intel ICH8 SATA Rev. 2.0 controller Kingston HyperX 3K 120GB SSD which supports SATA Rev. 3.0 Windows 7 Ultimate x64 For some reason I was unable to install Windows with the controller set in AHCI mode, even with the correct driver from Intel so it is currently in IDE mode. Due to the ICH8 controller being SATA Rev 2.0 and running in IDE mode, the SSD is operating well under it's published read/write speeds. I have ordered an Asus U3S6 controller card to add both SATA Rev. 3.0 and USB 3.0 to my computer. The motherboard does have a PCIe x4 slot available so I will hopefully achieve the full potential of my SSD. My question is this - am I able to swap the SSD over to the controller card from the motherboard controller without having to clean install Windows? I am hoping that all I will need to do is ensure that the controller card drivers are available to Windows and set the registry as per this KB article. Will this work or should I perform a clean installation?

  Read the article

• Looking for comprehensive computer monitoring software

  - by cornjuliox

  Summer in this country is insanely hot. So hot in fact, that I think we just lost a machine due to overheating (last recorded CPU/GPU temp was close to 100 C, now it wont start and lets out a long series of short beeps on power up), but that's not my concern here. Since heat is such a problem for me, I use several different pieces of software to monitor temperatures in my machine. I use MSI Afterburner to monitor GPU temp, control GPU fan speed and for some light overclocking, and then I use Speccy and SpeedFan to monitor the rest of the system, CPU temp and everything. The setup works fine for now, but I want to consolidate all this into one program so I'm not juggling several windows at once. Is there any program out there that will let me monitor the following from a single window: CPU Temp and Fan Speed CPU clock GPU Temp and Fan Speed GPU clock, both core and memory Additionally, mobo temp (Speccy lists both CPU and Motherboard temp, I assume that the latter is referring to North and Southbridge temperatures. I'm also looking for the ability to chart these data points on a graph over time, basically to see just how high the temperatures spike under load and for general analysis. It'd be nice if it could handle overclocking of both CPU and GPU in real time too. Any suggestions? Edit: I forgot to mention that I'm on Windows 7, 64-bit

  Read the article

• FTP not listing directory NcFTP PASV

  - by Jacob Talbot

  I am attempting to setup Multicraft on my server, all is running smoothly however the FTP won't allow anyone to connect from a remote FTP client, where net2ftp will work smoothly from a remote location. I have included the transcript from my FTP client, Transmit below to give you an idea of what's going on. I have disabled iptables as well, and still no luck either way. Transmit 4.1.7 (x86_64) Session Transcript [Version 10.8.2 (Build 12C54)] (21/10/12 11:23 PM) LibNcFTP 3.2.3 (July 23, 2009) compiled for UNIX 220: Multicraft 1.7.1 FTP server Connected to ateam.bn-mc.net. Cmd: USER jacob.9 331: Username ok, send password. Cmd: PASS xxxxxxxx 230: Login successful Cmd: TYPE A 200: Type set to: ASCII. Logged in to ateam.bn-mc.net as jacob.9. Cmd: SYST 215: UNIX Type: L8 Cmd: FEAT 211: Features supported: EPRT EPSV MDTM MLSD MLST type*;perm*;size*;modify*;unique*;unix.mode;unix.uid;unix.gid; REST STREAM SIZE TVFS UTF8 End FEAT. Cmd: OPTS UTF8 ON 200: OK Cmd: PWD 257: "/" is the current directory. Cmd: PASV Could not read reply from control connection -- timed out. (SReadline 1)

  Read the article

• Can't connect to MySQL on CentOS 5 Error 13 - Permission Denied

  - by abszero

  Ok, I have an install of CentOS 5 running as a GuestOS in VirtualBox. The network card for the Cent box is bridged with that of my host OS so that the boxes can see each other. Cent has an IP of 192.168.1.108 and my Host box has an IP of .104. Everything, with regard to networking, seems to be working properly as I can access the Drupal install that is on the Cent box from a web browser on my host box by navigating to http://192.168.1.108 however when I try to configure the database for Drupal through the Drupal install interface I am getting the Can't connect to MySQL error. First I thought this might of been a Firewall issue so I stopped iptables but that had no effect. I thought maybe the user I had setup did not have access to the server so I tried root and that did not work. Searching on the net said that I needed to provide a bind-address parameter to my.cnf so I did that with no change. (As a side note the length of my my.cnf file was MUCH shorter than the ones presented online. In fact under mysqld all I have are datadir, socket, user, and bind-address. Is this normal or should the file be more verbose?) After a few hours of messing with permissions and such I tried using 'localhost' as the value for the database server, from my HOST OS, and the Drupal install kicked off without a problem. So while my issue is resolved I am curious as to why 'localhost' works and why 192.168.1.108 did not? Is there something i need to do to specifically access the MySQL box via the aforementioned IP? Thanks.

  Read the article

• NetInstall working on some systems, not working on others

  - by cduruk

  Hi, I'm having an issue where my NetInstall setup works on some computers and fails on others. I am not able to diagnose the issue. I created an image of a Mac Mini and then created a NetRestore image using the System Image Utility found on Snow Leopard Server. NetBoot and NFS all seem to be working fine on the server, which is an XServe. Then I select the NetInstall image from the Startup Disk on a machine. On some of the machines, the process works as expected. On some of them, I see the globe icon blink a few times and then the system boots to the regular hard drive. I have captured the tracedump and the system.log logs from the server on both cases where NetInstall seems to work and fail. Here is the link that has all the logs http://gist.github.com/232232 The gist of the failure seems to be from the lack of BSDP DISCOVER in the failure but I'm not able to identify why that exactly is happening. I'd really appreciate any help on this issue.

  Read the article

• install latest gcc as a non-privileged user

  - by voth

  I want to compile a program on a cluster (as a non-privileged user), which requires gcc-4.6, but the cluster has only gcc-4.1.2. I don't want to tell the administrator to update gcc, because 1) he is busy and would do it only after several days. 2) He probably wouldn't update it anyway, since other users may need the older gcc version (gcc is not backward compatible) I tried to compile gcc from source, which seems more difficult that it sounds, since it requires several other packages to be installed (GMP, MPFR, MPC, ...), and when I did it, after several hours I got a message like checking for __gmpz_init in -lgmp... no configure: error: libgmp not found or uses a different ABI (including static vs shared). at which point a got stuck. My question is: what is the easiest way to install the latest version of gcc as a non-privileged user? (something like apt-get install XXXXX, with an option to not install as root for example) The setup of the cluster is the following: CentOS release 5.4 (Final) Rocks release 5.3 (Rolled Tacos) If there are no other options than compiling from source, do you have any ideas how to handle the above error?

  Read the article

• How to install IE9 when KB2120976 is not applicable to my Windows 7 x86 Ultimate edition?

  - by CVertex

  I'm trying to install IE9, visit http://beautyoftheweb.com, download it and then says it's downloading prereqs. After a minute, the installer says there's a problem and directs me to Prerequisites for installing Internet Explorer 9 Beta I click on the x86 installers one by one... most say "already installed".. But http://support.microsoft.com/kb/2120976/ says "The update is not applicable to your computer". Lame. So I try the IE9 install and the go through the whole process again with the same result. I discovered there's an IE9 install log at C:\Windows\IE9_main.log which logs the install process and reports an Error for 2120976 00:06.630: ERROR: Error installing prerequisite file (C:\Users\Vijay\AppData\Local\Temp\IE98036.tmp\KB2120976_x86.msu): 0x80240017 (2149842967) 00:06.677: INFO: PauseOrResumeAUThread: Successfully resumed Automatic Updates. 00:12.090: INFO: Link clicked, opening URL in new window:'http://go.microsoft.com/fwlink/?LinkId=185111' 00:12.106: INFO: Setup exit code: 0x00009C47 (40007) - Required updates are missing from the system.are missing from the system. Any idea why KB2120976 is inapplicable to my LEGAL Windows 7 Ultimate system? Any help is greatly appreciated.

  Read the article

• convert a logical partition to a primary partition

  - by ant2009

  Hello, Fedora 14 xfce I have the following partition setup. I would like to know how can I convert the logical partition sda6 to a primary partition. Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1707a8a5 Device Boot Start End Blocks Id System /dev/sda1 2048 1026047 512000 83 Linux /dev/sda2 1026048 205844479 102409216 83 Linux /dev/sda3 205844480 214228991 4192256 82 Linux swap / Solaris /dev/sda4 214228992 625141759 205456384 5 Extended /dev/sda5 214231040 573562879 179665920 83 Linux /dev/sda6 573564928 625141759 25788416 7 HPFS/NTFS Filesystem Size Used Avail Use% Mounted on /dev/sda2 97G 5.0G 91G 6% / tmpfs 494M 176K 494M 1% /dev/shm /dev/sda1 485M 68M 392M 15% /boot /dev/sda5 169G 26G 135G 16% /home # partition table of /dev/sda unit: sectors /dev/sda1 : start= 2048, size= 1024000, Id=83 /dev/sda2 : start= 1026048, size=204818432, Id=83 /dev/sda3 : start=205844480, size= 8384512, Id=82 /dev/sda4 : start=214228992, size=410912768, Id= 5 /dev/sda5 : start=214231040, size=359331840, Id=83 /dev/sda6 : start=573564928, size= 51576832, Id= 7 I would like to convert sda6 to a primary partition, the reason for this it to install windows 7 starter. Many thanks for any suggestions,

  Read the article

• ZFS with L2ARC (SSD) slower for random seeks than without L2ARC

  - by Florian Kruse

  I am currently testing ZFS (Opensolaris 2009.06) in an older fileserver to evaluate its use for our needs. Our current setup is as follows: Dual core (2,4 GHz) with 4 GB RAM 3x SATA controller with 11 HDDs (250 GB) and one SSD (OCZ Vertex 2 100 GB) We want to evaluate the use of a L2ARC, so the current ZPOOL is: $ zpool status pool: tank state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM afstank ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c11t0d0 ONLINE 0 0 0 c11t1d0 ONLINE 0 0 0 c11t2d0 ONLINE 0 0 0 c11t3d0 ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c13t0d0 ONLINE 0 0 0 c13t1d0 ONLINE 0 0 0 c13t2d0 ONLINE 0 0 0 c13t3d0 ONLINE 0 0 0 cache c14t3d0 ONLINE 0 0 0 where c14t3d0 is the SSD (of course). We run IO tests with bonnie++ 1.03d, size is set to 200 GB (-s 200g) so that the test sample will never be completely in ARC/L2ARC. The results without SSD are (average values over several runs which show no differences) write_chr write_blk rewrite read_chr read_blk random seeks 101.998 kB/s 214.258 kB/s 96.673 kB/s 77.702 kB/s 254.695 kB/s 900 /s With SSD it becomes interesting. My assumption was that the results should be in worst case at least the same. While write/read/rewrite rates are not different, the random seek rate differs significantly between individual bonnie++ runs (between 188 /s and 1333 /s so far), average is 548 +- 200 /s, so below the value w/o SSD. So, my questions are mainly: Why do the random seek rates differ so much? If the seeks are really random, they should not differ much (my assumption). So, even if the SSD is impairing the performance it should be the same in each bonnie++ run. Why is the random seek performance worse in most of the bonnie++ runs? I would assume that some part of the bonnie++ data is in the L2ARC and random seeks on this data performs better while random seeks on other data just performs similarly like before.

  Read the article

• How to best tune my SAN/Initiators for best performance?

  - by Disco

  Recent owner of a Dell PowerVault MD3600i i'm experiencing some weird results. I have a dedicated 24x 10GbE Switch (PowerConnect 8024), setup to jumbo frames 9K. The MD3600 has 2 RAID controllers, each has 2x 10GbE ethernet nics. There's nothing else on the switch; one VLAN for SAN traffic. Here's my multipath.conf defaults { udev_dir /dev polling_interval 5 selector "round-robin 0" path_grouping_policy multibus getuid_callout "/sbin/scsi_id -g -u -s /block/%n" prio_callout none path_checker readsector0 rr_min_io 100 max_fds 8192 rr_weight priorities failback immediate no_path_retry fail user_friendly_names yes # prio rdac } blacklist { device { vendor "*" product "Universal Xport" } # devnode "^sd[a-z]" } devices { device { vendor "DELL" product "MD36xxi" path_grouping_policy group_by_prio prio rdac # polling_interval 5 path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And iscsid.conf : node.startup = automatic node.session.timeo.replacement_timeout = 15 node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 10 node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 After my tests; i can barely come to 200 Mb/s read/write. Should I expect more than that ? Providing it has dual 10 GbE my thoughts where to come around the 400 Mb/s. Any ideas ? Guidelines ? Troubleshooting tips ?

  Read the article

• port forwarding with socks over proxy

  - by Oz123

  I am trying to browse a wiki that runs on a server inside one domain from another domain. The wiki is accessible only on the LAN, but I need to browse it from another LAN to which I connect with an SSH tunnel ... Here is my setup and the steps I did so far: ~.ssh/confing on wikihost: Host gateway User kisteuser Port 443 Hostname gateway.companydomain.com ProxyCommand /home/myuser/bin/ssh-https-tunnel %h %p # ssh-https-tunnel: # http://ttcplinux.sourceforge.net/tools/stunnel Protocol 2 IdentityFile ~/.ssh/key_dsa LocalForward 11069 localhost:11069 Host server1 User kisteuser Hostname localhost Port 11069 LocalForward 8022 server1:22 LocalForward 17001 server1:7100 LocalForward 8080 www-proxy:3128 RemoteForward 11069 localhost:22 from wikihost myuser@wikihost: ssh -XC -t gateway.companydomain.com ssh -L11069:localhost:22 server1 on another terminal: ssh gateway.companydomain.com Now, on my companydomain I would like to start firefox and browse the wiki on wikihost. I did: [email protected] ~ $ ssh gateway Have a lot of fun... kisteuser@gateway ~ $ ssh -D 8383 localhost user@localhost's password: user@wikiserver:~> My .ssh/config on that side looks like that: host server1 localforward 11069 localhost:11069 host localhost user myuser port 11069 host wikiserver forwardagent yes user myuser port 11069 hostname localhost Now, I started firefox on the server called gateway, and edited the proxy settings to use SOCKSv5, specifying that the proxy should be gateway and use the port 8383... kisteuser@gateway ~ $ LANG=C firefox -P --no-remote And, now I get the following error popping in the Terminal of wikiserver: myuser@wikiserver:~> channel 3: open failed: connect failed: Connection refused channel 3: open failed: connect failed: Connection refused channel 3: open failed: connect failed: Connection refused Confused? Me too ... Please help me understand how to properly build the tunnels and browse the wiki over SOCKS protocol. update: I managed to browse the wiki on wikiserver with the following changes: host wikiserver forwardagent yes user myuser port 11069 hostname localhost localforward 8339 localhost:8443 Now when I ssh gateway I launch Firefox and go to localhost:8339 and I hit the start page of the wiki, which is served on Port 8443. Now I ask myself is SOCKS really needed? Can someone elaborate on that ?

  Read the article

• Network Load Balancing, intermittent port problem on Windows Server 2008

  - by Jimmy Chandra

  Trying to troubleshoot an intermittent problem on a Windows Server 2008 NLB. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

  Read the article

• Tips and Suggestions IP Address Re-Addressing?

  - by RSXAdmin

  Hello serverfault Universe, My ever evolving and expanding local area network is currently using a class-C address. My network consists of multiple subnets depending on site/location. 192.168.1.x is site HQ 192.168.5.x is secondary site 192.168.10.x is so on and so forth. Long story short - I have inherited this network design from the previous admin who has left the company which started off with a dozen people and now has just over 300 full time/part time employees. We do not yet have client VPN access; but we do have site to site VPN setup. My question is, in preparation for outside client access to my network via Cisco ASA, I would like to re-address the HQ site because I understand a 192.168.1.x or 192.168.0.x are not very good choices for a company subnet - it may conflict with a home user's LAN when connecting to my LAN, I believe? Through your experience, does anyone out there have any suggestions and tips on how I can proceed with re-addressing my subnets. If I designed this network I would have gone with a 10.0.0.0 (mask 255.255.255.0) so I am leaning towards changing it to fit. Thank you.

  Read the article

• NAT confusion regarding cisco ASA5510

  - by LonelyLonelyNetworkN00b

  I'm setting up my first cisco firewalls. A little information first:I have two asa5510 setup in a working active/standby pair. From my ISP i have two public subnets. A /29 and a /26. On my DMZ interface i have the /26 configured. On my WAN Interface i have configured the /29 IPs. My isp routes the /26 via the /29 primary IP. I'm running ASA 8.2. I've turned NAT-Control off, because i don't want to use nat for for other than some internal interfaces. In essence i don't want to use NAT unless i specify it. I have a internal interface with the network of 192.168.100.0/24. I've tried setting up nat limke this: nat (inside) 1 192.168.100.0 255.255.255.0 global (WAN) 1 interface I was under the impression that this would let connections that was going from 192.168.100.0/24 and out the WAN interface to be Port-Address-translated. I'm not getting this to work for some reason. Inside interface has security level of 100, and wan has security level of 0.

  Read the article

< Previous Page | 568 569 570 571 572 573 574 575 576 577 578 579  | Next Page >