duplicate ip - Page 583

How do I configure OpenVPN for accessing the internet with one NIC?

- by Lekensteyn

I've been trying to get OpenVPN to work for three days. After reading many questions, the HOWTO, the FAQ and even parts of a guide to Linux networking, I cannot get my an Internet connection to the Internet. I'm trying to set up a OpenVPN server on a VPS, which will be used for: secure access to the Internet bypassing port restrictions (directadmin/2222 for example) an IPv6 connection (my client does only have IPv4 connectivity, while the VPS has both IPv4 and native IPv6 connectivity) (if possible) I can connect to my server and access the machine (HTTP), but Internet connectivity fails completely. I'm using ping 8.8.8.8 for testing whether my connection works or not. Using tcpdump and iptables -t nat -A POSTROUTING -j LOG, I can confirm that the packets reach my server. If I ping to 8.8.8.8 on the VPS, I get an echo-reply from 8.8.8.8 as expected. When pinging from the client, I do not get an echo-reply. The VPS has only one NIC: etho. It runs on Xen. Summary: I want to have a secure connection between my laptop and the Internet using OpenVPN. If that works, I want to have IPv6 connectivity as well. Network setup and software: Home laptop (eth0: 192.168.2.10) (tap0: 10.8.0.2) | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | router/gateway (gateway 192.168.2.1) | INTERNET | VPS (eth0:1.2.3.4) (gateway, tap0: 10.8.0.1) (running Debian 6; OpenVPN 2.1.3-2) wifi and my home router should not cause problems since all traffic goes encrypted over UDP port 1194. I've turned IP forwarding on: # echo 1 > /proc/sys/net/ipv4/ip_forward iptables has been configured to allow forwarding traffic as well: iptables -F FORWARD iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -A FORWARD -j DROP I've tried each of these rules separately without luck (flushing the chains before executing): iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j SNAT --to 1.2.3.4 iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE route -n before (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n after (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n before (client): 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 route -n after (client): 1.2.3.4 192.168.2.1 255.255.255.255 UGH 0 0 0 wlan0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 128.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 SERVER config proto udp dev tap ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" ifconfig-pool-persist ipp.txt keepalive 10 120 tls-auth ta.key 0 comp-lzo user nobody group nobody persist-key persist-tun log-append openvpn-log verb 3 mute 10 CLIENT config dev tap proto udp remote 1.2.3.4 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 traceroute 8.8.8.8 works as expected (similar output without OpenVPN activated): 1 10.8.0.1 (10.8.0.1) 24.276 ms 26.891 ms 29.454 ms 2 gw03.sbp.directvps.nl (178.21.112.1) 31.161 ms 31.890 ms 34.458 ms 3 ge0-v0652.cr0.nik-ams.nl.as8312.net (195.210.57.105) 35.353 ms 36.874 ms 38.403 ms 4 ge0-v3900.cr0.nik-ams.nl.as8312.net (195.210.57.53) 41.311 ms 41.561 ms 43.006 ms 5 * * * 6 209.85.248.88 (209.85.248.88) 147.061 ms 36.931 ms 28.063 ms 7 216.239.49.36 (216.239.49.36) 31.109 ms 33.292 ms 216.239.49.28 (216.239.49.28) 64.723 ms 8 209.85.255.130 (209.85.255.130) 49.350 ms 209.85.255.126 (209.85.255.126) 49.619 ms 209.85.255.122 (209.85.255.122) 52.416 ms 9 google-public-dns-a.google.com (8.8.8.8) 41.266 ms 44.054 ms 44.730 ms If you have any suggestions, please comment or answer. Thanks in advance.

Read the article

Varnish default.vcl grace period

- by Vladimir

These are my settings for a grace period (/etc/varnish/default.vcl) sub vcl_recv { .... set req.grace = 360000s; ... } sub vcl_fetch { ... set beresp.grace = 360000s; ... } I tested Varnish using localhost and nodejs as a server. I started localhost, the site was up. Then I disconnected server and the site got disconnected in less than 2 min. It says: Error 503 Service Unavailable Service Unavailable Guru Meditation: XID: 1890127100 Varnish cache server Could you tell me what could be the problem? sub vcl_fetch { if (beresp.ttl < 120s) { ##std.log("Adjusting TTL"); set beresp.ttl = 36000s; ##120s; } # Do not cache the object if the backend application does not want us to. if (beresp.http.Cache-Control ~ "(no-cache|no-store|private|must-revalidate)") { return(hit_for_pass); } # Do not cache the object if the status is not in the 200s if (beresp.status >= 300) { # Remove the Set-Cookie header #remove beresp.http.Set-Cookie; return(hit_for_pass); } # # Everything below here should be cached # # Remove the Set-Cookie header ####remove beresp.http.Set-Cookie; # Set the grace time ## set beresp.grace = 1s; //change this to minutes in case of app shutdown set beresp.grace = 360000s; ## 10 hour - reduce if it has negative impact # Static assets - browser caches tpiphem for a long time. if (req.url ~ "\.(css|js|.js|jpg|jpeg|gif|ico|png)\??\d*$") { /* Remove Expires from backend, it's not long enough */ unset beresp.http.expires; /* Set the clients TTL on this object */ set beresp.http.cache-control = "public, max-age=31536000"; /* marker for vcl_deliver to reset Age: */ set beresp.http.magicmarker = "1"; } else { set beresp.http.Cache-Control = "private, max-age=0, must-revalidate"; set beresp.http.Pragma = "no-cache"; } if (req.url ~ "\.(css|js|min|)\??\d*$") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } ##do not duplicate these settings if (req.url ~ ".css") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } if (req.url ~ ".js") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } if (req.url ~ ".min") { set beresp.do_gzip = true; unset beresp.http.expires; set beresp.http.cache-control = "public, max-age=31536000"; set beresp.http.expires = beresp.ttl; set beresp.http.age = "0"; } ## If the request to the backend returns a code other than 200, restart the loop ## If the number of restarts reaches the value of the parameter max_restarts, ## the request will be error'ed. max_restarts defaults to 4. This prevents ## an eternal loop in the event that, e.g., the object does not exist at all. if (beresp.status != 200 && beresp.status != 403 && beresp.status != 404) { return(restart); } if (beresp.status == 302) { return(deliver); } # Never cache posts if (req.url ~ "\/post\/" || req.url ~ "\/submit\/" || req.url ~ "\/ask\/" || req.url ~ "\/add\/") { return(hit_for_pass); } ##check this setting to ensure that it does not cause issues for browsers with no gzip if (beresp.http.content-type ~ "text") { set beresp.do_gzip = true; } if (beresp.http.Set-Cookie) { return(deliver); } ##if (req.url == "/index.html") { set beresp.do_esi = true; ##} ## check if this is needed or should be used # return(deliver); the object return(deliver); } sub vcl_recv { ##avoid leeching of images call hot_link; set req.grace = 360000s; ##2m ## if one backend is down - use another if (req.restarts == 0) { set req.backend = cache_director; ##we can specify individual VMs } else if (req.restarts == 1) { set req.backend = cache_director; } ## post calls should not be cached - add cookie for these requests if using micro-caching # Pass requests that are not GET or HEAD if (req.request != "GET" && req.request != "HEAD") { return(pass); ## return(pass) goes to backend - not cache } # Don't cache the result of a redirect if (req.http.Referer ~ "redir" || req.http.Origin ~ "jumpto") { return(pass); } # Don't cache the result of a redirect (asking for logon) if (req.http.Referer ~ "post" || req.http.Referer ~ "submit" || req.http.Referer ~ "add" || req.http.Referer ~ "ask") { return(pass); } # Never cache posts - ensure that we do not use these strings in our URLs' that need to be cached if (req.url ~ "\/post\/" || req.url ~ "\/submit\/" || req.url ~ "\/ask\/" || req.url ~ "\/add\/") { return(pass); } ## if (req.http.Authorization || req.http.Cookie) { if (req.http.Authorization) { /* Not cacheable by default */ return (pass); } # Handle compression correctly. Different browsers send different # "Accept-Encoding" headers, even though they mostly all support the same # compression mechanisms. By consolidating these compression headers into # a consistent format, we can reduce the size of the cache and get more hits. # @see: http:// varnish.projects.linpro.no/wiki/FAQ/Compression if (req.http.Accept-Encoding) { if (req.url ~ "\.(jpg|png|gif|gz|tgz|bz2|tbz|mp3|ogg|ico)$") { # No point in compressing these remove req.http.Accept-Encoding; } else if (req.http.Accept-Encoding ~ "gzip") { # If the browser supports it, we'll use gzip. set req.http.Accept-Encoding = "gzip"; } else if (req.http.Accept-Encoding ~ "deflate") { # Next, try deflate if it is supported. set req.http.Accept-Encoding = "deflate"; } else { # Unknown algorithm. Remove it and send unencoded. unset req.http.Accept-Encoding; } } # lookup graphics, css, js & ico files in the cache if (req.url ~ "\.(png|gif|jpg|jpeg|css|.js|ico)$") { return(lookup); } ##added on 0918 - check if it causes issues with user specific content if (req.request == "GET" && req.http.cookie) { return(lookup); } # Pipe requests that are non-RFC2616 or CONNECT which is weird. if (req.request != "GET" && req.request != "HEAD" && req.request != "PUT" && req.request != "POST" && req.request != "TRACE" && req.request != "OPTIONS" && req.request != "DELETE") { ##closing connection and calling pipe return(pipe); } ##purge content via localhost only if (req.request == "PURGE") { if (!client.ip ~ purge) { error 405 "Not allowed."; } return(lookup); } ## do we need this? ## return(lookup); }

Read the article

Varnish 3.0.2 to Apache2 sometimes return error 503

- by Ronnie Jespersen

Hey guys I hope you can help me out here. I have an Ngingx parsing http and https to a varnish cache(3.0.2). From the varnish it is sent to apache2. Now I have for some time been tracking some strange 503 errors. But I cant seem to find the silver bullet. Currently I am logging the 503 errors through varnish this way: sudo varnishlog -c -m TxStatus:503 >> /home/rj/varnishlog503.log and then referring to the apache access log to see if any 503 requests have been handled. Today I had a health check from the firewall that failed: 20 SessionOpen c 127.0.0.1 34319 :8081 20 ReqStart c 127.0.0.1 34319 607335635 20 RxRequest c HEAD 20 RxURL c /health-check 20 RxProtocol c HTTP/1.0 20 RxHeader c X-Real-IP: 192.168.3.254 20 RxHeader c Host: 192.168.3.189 20 RxHeader c X-Forwarded-For: 192.168.3.254 20 RxHeader c Connection: close 20 RxHeader c User-Agent: Astaro Service Monitor 0.9 20 RxHeader c Accept: */* 20 VCL_call c recv lookup 20 VCL_call c hash 20 Hash c /health-check 20 VCL_return c hash 20 VCL_call c miss fetch 20 Backend c 33 aurum aurum 20 FetchError c http first read error: -1 11 (No error recorded) 20 VCL_call c error deliver 20 VCL_call c deliver deliver 20 TxProtocol c HTTP/1.1 20 TxStatus c 503 20 TxResponse c Service Unavailable 20 TxHeader c Server: Varnish 20 TxHeader c Content-Type: text/html; charset=utf-8 20 TxHeader c Retry-After: 5 20 TxHeader c Content-Length: 879 20 TxHeader c Accept-Ranges: bytes 20 TxHeader c Date: Wed, 06 Jun 2012 12:35:12 GMT 20 TxHeader c X-Varnish: 607335635 20 TxHeader c Age: 60 20 TxHeader c Via: 1.1 varnish 20 TxHeader c Connection: close 20 Length c 879 20 ReqEnd c 607335635 1338986052.649786949 1338986112.648169994 0.000160217 59.997980356 0.000402689 Now the backend server (apache) does not have any 503 error in the access log at this point. So I am confused. Is this varnish throwing a 503 because it thinks apache is to slow? There is a lot traffic coming through at this point so I know the server is up and running. I do have other 503 error codes with posts and gets so there is really no pattern. It seems to be at random times and random requests. Even in the morning when the server dosen't seem to be doing anything. I do see another pattern in the log: 4 VCL_call c recv pass 4 VCL_call c hash 4 Hash c /?id=412 4 VCL_return c hash 4 VCL_call c pass pass 4 FetchError c no backend connection 4 VCL_call c error deliver 4 VCL_call c deliver deliver Here fetcherror says "no backend connection". A summery of the FetchErrors in todays log: 16 FetchError c http first read error: -1 11 (No error recorded) 5 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 19 FetchError c http first read error: -1 11 (No error recorded) 5 FetchError c http first read error: -1 11 (No error recorded) 23 FetchError c http first read error: -1 11 (No error recorded) 24 FetchError c http first read error: -1 11 (No error recorded) 16 FetchError c http first read error: -1 11 (No error recorded) 6 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 5 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 4 FetchError c http first read error: -1 11 (No error recorded) 22 FetchError c http first read error: -1 11 (No error recorded) 6 FetchError c http first read error: -1 11 (No error recorded) 21 FetchError c http first read error: -1 11 (No error recorded) 26 FetchError c no backend connection 4 FetchError c no backend connection 20 FetchError c http first read error: -1 11 (No error recorded) 39 FetchError c http first read error: -1 11 (No error recorded) I haven't changed the default timeout values for varnish. This is my configuration for one of the backend servers. backend xenon { .host = "192.168.3.187"; .port = "80"; .probe = { .url = "/health-check/"; .interval = 3s; .window = 5; .threshold = 2; } } I'm running prefork module on apache2 with this configuration <IfModule mpm_prefork_module> StartServers 1 MinSpareServers 2 MaxSpareServers 5 MaxClients 200 MaxRequestsPerChild 75 </IfModule> and only PHP files is sent to the server. Every other static file is handled by Nginx. Any ideas? ------- EDIT -------------- Some more debuging information I have run a varnishadm debug.health Backend radon is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.002560 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy Backend xenon is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.002760 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy Backend iridium is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.000849 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy Backend aurum is Healthy Current states good: 5 threshold: 2 window: 5 Average responsetime of good probes: 0.002100 Oldest Newest ================================================================ 4444444444444444444444444444444444444444444444444444444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH Happy And I have been monitoring varnishstat from the two load balancers 3224774 3.99 2.61 backend_conn - Backend conn. success 27 0.00 0.00 backend_unhealthy - Backend conn. not attempted 63 0.00 0.00 backend_fail - Backend conn. failures 358798 0.00 0.29 backend_reuse - Backend conn. reuses 21035 0.00 0.02 backend_toolate - Backend conn. was closed 379834 0.00 0.31 backend_recycle - Backend conn. recycles 26 0.00 0.00 backend_retry - Backend conn. retry 3217751 5.99 2.61 backend_conn - Backend conn. success 32 0.00 0.00 backend_fail - Backend conn. failures 364185 0.00 0.30 backend_reuse - Backend conn. reuses 27077 0.00 0.02 backend_toolate - Backend conn. was closed 391263 0.00 0.32 backend_recycle - Backend conn. recycles 36 0.00 0.00 backend_retry - Backend conn. retry Notice that none of them have reported backend_fail. /Ronnie

Read the article

What is Causing this IIS 7 Web Service Sporadic Connectivity Error?

- by dpalau

On sporadic occasions we receive the following error when attempting to call an .asmx web service from a .Net client application: "The underlying connection was closed: A connection that was expected to be kept alive was closed by the server. Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host." By sporadic I mean that it might occur zero, once every few days, or a half-dozen times a day for some users. It will never occur for the first web service call of a user. And the subsequent (usually the same) call will always work immediately after the failure. The failures happen across a variety of methods in the service and usually happens between 15-20 seconds (according to the log) from the time of the request. Looking in the IIS site log for the particular call will show one or the other of the following windows error codes: 121: The semaphore timeout period has elapsed. 1236: The network connection was aborted by the local system. Some additional environment details: Running on internal network web farm consisting of two servers running IIS7 on Windows Server 2008 OS. These problems did not occur when running in an older IIS6 web farm of three servers running on Windows Server 2003 (and we use a single IIS6/2003 instance for our development and staging environments with no issues). EDIT: Also, all of these server instances are VMWare virtual machines, not sure if that is a surprise anymore or not. The web service is a .Net 2.0/3.5 compiled .asmx web service that has its own application pool (.Net 2.0, integrated pipeline). Only has Windows Authentication enabled. We have another web service on the farm that uses the same physical path as the primary service, the only difference being that Basic Authentication is enabled. This is used for a portion of our ERP system. Have tried using the same and different application pool - no effect on the error. This site isn't hit as often as the primary site and has never had an error. As mentioned, the error will only happen when called from the .Net client - not from other applications. The client application is always creating a new web service object for each request and setting the service credentials to System.Net.CredentialCache.DefaultCredentials. The application is either deployed locally to a client or run in a Citrix server session. Those users running in Citrix doesn't seem to experience the issue, only locally deployed clients. The Citrix servers and the web farm are located in the same physical location and are located in the same IP range (10.67.xx.xx). Locally deployed clients experiencing the error are located elsewhere (10.105.xx.xx, 10.31.xx.xx). I've checked the OS logs to see if I can see any problems but nothing really sticks out. EDIT: Actually, I myself just ran into the error a little bit ago. I decided to check out the logs again and saw that there was a Security log entry of "Audit Failure" at the 'same' time (IIS log entry at 1:39:59, event log entry at 1:39:50). Not sure if this is a coincidence or not, I'll have to check out the logs of previous errors. I'm probably grasping for straws but the details: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 7/8/2009 1:39:50 PM Event ID: 5159 Task Category: Filtering Platform Connection Level: Information Keywords: Audit Failure User: N/A Computer: is071019.<**.net Description: The Windows Filtering Platform has blocked a bind to a local port. Application Information: Process ID: 1260 Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Source Address: 0.0.0.0 Source Port: 54802 Protocol: 17 Filter Information: Filter Run-Time ID: 0 Layer Name: Resource Assignment Layer Run-Time ID: 36 I've also tried to use Failed Request Tracing in IIS7 but the service call never actually gets to where FRT can capture it (even though the failure is logged in the web service log). The network infrastructure group said they checked out the DNS and any NIC settings are correct so there is no 'flapping'. Everything pans out. I'm not sure that they checked out any domain controller servers though to see if that could be an issue. Any ideas? Or any other debugging strategies to get to the bottom of this? I'm just the developer in charge of the software and don't really have the knowledge on what to investigate from the networking side of things - although it does sound like a networking issue to me based on what is happening. Thanks in advance for any help.

Read the article

Site-to-Site PPTP VPN connection between two Windows Server 2008 R2 servers

- by steve_eyre

We have two Windows Server 2008 R2 machines, one in our main office and one in a new office which we have just moved offsite. The main office has previously been handling client-to-server PPTP VPN connections. Now that we have moved our second server out of office, we want to set up a demand-dial or persistent VPN connection from the second server to the primary. Using a custom setting RRAS profile, we have successfully managed to set up a site-to-site VPN connection so that from the second server itself, it can access any of the devices in the main office and communicate back. However, any connected machines in the second office cannot use this connection, even when using the second server as gateway. The demand-dial interface is setup from the Second Server dialing into Main Server and a static route set up on RRAS for 192.168.0.0 with subnet mask 255.255.0.0 pointing down this network interface. The main office has the network of 192.168.0.0/16 (subnet mask 255.255.0.0). The second office has the network of 172.16.100.0/24 (subnet mask 255.255.255.0). What steps do we need to take to ensure traffic from the second office PCs going towards 192.168.x.x addresses use the VPN route? Many Thanks in advance for any help the community can offer. Debug Information Here is the route print output from the second server: =========================================================================== Interface List 23...........................Main Office 22...........................RAS (Dial In) Interface 16...e0 db 55 12 fa 02 ......Local Area Connection - Virtual Network 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 24...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.222 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 <MAIN OFFICE IP> 255.255.255.255 172.16.100.250 172.16.100.222 6 172.16.100.0 255.255.255.0 On-link 172.16.100.222 261 172.16.100.113 255.255.255.255 On-link 172.16.100.113 306 172.16.100.222 255.255.255.255 On-link 172.16.100.222 261 172.16.100.223 255.255.255.255 On-link 172.16.100.222 261 172.16.100.224 255.255.255.255 On-link 172.16.100.222 261 172.16.100.225 255.255.255.255 On-link 172.16.100.222 261 172.16.100.226 255.255.255.255 On-link 172.16.100.222 261 172.16.100.227 255.255.255.255 On-link 172.16.100.222 261 172.16.100.228 255.255.255.255 On-link 172.16.100.222 261 172.16.100.229 255.255.255.255 On-link 172.16.100.222 261 172.16.100.230 255.255.255.255 On-link 172.16.100.222 261 172.16.100.255 255.255.255.255 On-link 172.16.100.222 261 192.168.0.0 255.255.0.0 192.168.101.87 192.168.101.17 266 192.168.101.17 255.255.255.255 On-link 192.168.101.17 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.222 261 224.0.0.0 240.0.0.0 On-link 172.16.100.113 306 224.0.0.0 240.0.0.0 On-link 192.168.101.17 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.222 261 255.255.255.255 255.255.255.255 On-link 172.16.100.113 306 255.255.255.255 255.255.255.255 On-link 192.168.101.17 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.0.200 Default 0.0.0.0 0.0.0.0 172.16.100.250 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 16 261 fe80::/64 On-link 16 261 fe80::edf4:85c6:3c15:dcbe/128 On-link 1 306 ff00::/8 On-link 16 261 ff00::/8 On-link 22 306 ff00::/8 On-link =========================================================================== Persistent Routes: None And here is the route print from one of the second office PCs: =========================================================================== Interface List 11...10 78 d2 32 53 27 ......Atheros AR8151 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.103 10 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.100.0 255.255.255.0 On-link 172.16.100.103 266 172.16.100.103 255.255.255.255 On-link 172.16.100.103 266 172.16.100.255 255.255.255.255 On-link 172.16.100.103 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.103 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.103 266 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 11 266 fe80::/64 On-link 11 266 fe80::e973:de17:a045:aa78/128 On-link 1 306 ff00::/8 On-link 11 266 ff00::/8 On-link =========================================================================== Persistent Routes: None

Read the article

Nginx + Haproxy + Thin + Rails - 503 Service Unavailable -

- by Luca G. Soave

I don't know how troubleshoot this. I get "503 Service Unavailable" http error for all "nginx upstreams" proxy passing calls to haproxy fast_thin and slow_thin ( server 127.0.0.1:3100 and server 127.0.0.1:3200 ), which loadbalance on 6 Thin servers ( 127.0.0.1:3000 .. 3005 ). Static files like /blog are currently fine. The falldown is: nginx on port 80 - haproxy on 3100 and 3200 - thin on 3000 .. 3005 and then Rails. Here it is /etc/nginx/nginx.conf : user nginx; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; sendfile on; tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; include /etc/nginx/conf.d/*.conf; } then /etc/nginx/conf.d/default.conf upstream fast_thin { server 127.0.0.1:3100; } upstream slow_thin { server 127.0.0.1:3200; } server { listen 80; server_name www.gitwatcher.com; rewrite ^/(.*) http://gitwatcher.com/$1 permanent; } server { listen 80; server_name gitwatcher.com; access_log /var/www/gitwatcher/log/access.log; error_log /var/www/gitwatcher/log/error.log; root /var/www/gitwatcher/public; # index index.html; location /about { proxy_pass http://fast_thin; break; } location /trends { proxy_pass http://slow_thin; break; } location /categories { proxy_pass http://slow_thin; break; } location /signout { proxy_pass http://slow_thin; break; } location /auth/github { proxy_pass http://slow_thin; break; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (-f $request_filename/index.html) { rewrite (.*) $1/index.html break; } if (-f $request_filename.html) { rewrite (.*) $1.html break; } if (!-f $request_filename) { proxy_pass http://slow_thin; break; } } } then haproxy config file /etc/haproxy/haproxy.cfg : global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet nbproc 1 # number of processing cores defaults log global retries 3 maxconn 2000 contimeout 5000 mode http clitimeout 60000 # maximum inactivity time on the client side srvtimeout 30000 # maximum inactivity time on the server side timeout connect 4000 # maximum time to wait for a connection attempt to a server to succeed option httplog option dontlognull option redispatch option httpclose # disable keepalive (HAProxy does not yet support the HTTP keep-alive mode) option abortonclose # enable early dropping of aborted requests from pending queue option httpchk # enable HTTP protocol to check on servers health option forwardfor # enable insert of X-Forwarded-For headers balance roundrobin # each server is used in turns, according to assigned weight stats enable # enable web-stats at /haproxy?stats stats auth haproxy:pr0xystats # force HTTP Auth to view stats stats refresh 5s # refresh rate of stats page listen rails_proxy 127.0.0.1:3100 # - equal weights on all servers # - maxconn will queue requests at HAProxy if limit is reached # - minconn dynamically scales the connection concurrency (bound my maxconn) depending on size of HAProxy queue # - check health every 20000 microseconds server web1 127.0.0.1:3000 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3001 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3002 weight 1 minconn 3 maxconn 6 check inter 20000 listen slow_proxy 127.0.0.1:3200 # cluster for slow requests, lower the queues, check less frequently server slow1 127.0.0.1:3003 weight 1 minconn 1 maxconn 3 check inter 40000 server slow2 127.0.0.1:3004 weight 1 minconn 1 maxconn 3 check inter 40000 server slow3 127.0.0.1:3005 weight 1 minconn 1 maxconn 3 check inter 40000 and the Thin config file /etc/thin/gitwatcher.yml : --- chdir: /var/www/gitwatcher environment: production address: 0.0.0.0 port: 3000 timeout: 30 log: log/thin.log pid: tmp/pids/thin.pid max_conns: 1024 max_persistent_conns: 100 require: [] wait: 30 servers: 6 daemonize: true if I look into open listen ports, I got the following : root@fullness:/var/www/gitwatcher# lsof | grep TCP | egrep "nginx|haproxy|thin" nginx 834 root 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 835 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 837 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) haproxy 1908 haproxy 4u IPv4 11699 0t0 TCP localhost:3100 (LISTEN) haproxy 1908 haproxy 6u IPv4 11701 0t0 TCP localhost:3200 (LISTEN) root@fullness:/var/www/gitwatcher# iptables -L get me the following : Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:22222 ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT all -- anywhere anywhere DROP all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Any help ?

Read the article

Ubuntu, No wireless networks found after correctly installed madwifi

- by Peter

Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

Read the article

squid3 auth thru samba using ntlm to AD doesn't work

- by derty

some users here are spending to much time exploring the WWW. So big boss whats to get this under control. We use a squid3 just for some security reason and chace benefits. and now i'm trying to set up a new proxy on a different server (Debian 6) Permissions are defined in AC and the squid3 should get the auth thru samba/winbind by using the ntlm protocol. but i'll get all the time Access, denited. it only works by using LDAP but thats not the way i need it. here some log and confs squid access.log 1326878095.784 1 192.168.15.27 TCP_DENIED/407 4049 GET http://at.msn.com/? -NONE/- text/html 1326878095.791 1 192.168.15.27 TCP_DENIED/407 4294 GET http://at.msn.com/? - NONE/- text/html 1326878095.803 9 192.168.15.27 TCP_DENIED/403 4028 GET http://at.msn.com/? kavan NONE/- text/html 1326878095.848 0 192.168.15.27 TCP_DENIED/403 3881 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878100.279 0 192.168.15.27 TCP_DENIED/403 3735 GET http://www.google.at/ kavan NONE/- text/html 1326878100.296 0 192.168.15.27 TCP_DENIED/403 3870 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878155.700 0 192.168.15.27 TCP_DENIED/407 4072 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.705 2 192.168.15.27 TCP_DENIED/407 4317 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.709 3 192.168.15.27 TCP_DENIED/403 4026 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml kavan NONE/- text/html squid chace 2012/01/18 10:12:49| Creating Swap Directories 2012/01/18 10:12:49| Starting Squid Cache version 3.1.6 for x86_64-pc-linux-gnu... 2012/01/18 10:12:49| Process ID 17236 2012/01/18 10:12:49| With 65535 file descriptors available 2012/01/18 10:12:49| Initializing IP Cache... 2012/01/18 10:12:49| DNS Socket created at [::], FD 7 2012/01/18 10:12:49| DNS Socket created at 0.0.0.0, FD 8 2012/01/18 10:12:49| Adding nameserver 192.168.15.2 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.19 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.1 from /etc/resolv.conf 2012/01/18 10:12:49| Adding domain schoenbrunn.local from /etc/resolv.conf 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'ntlm_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'squid_kerb_auth' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_group' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| Unlinkd pipe opened on FD 73 2012/01/18 10:12:49| Local cache digest enabled; rebuild/rewrite every 3600/3600 sec 2012/01/18 10:12:49| Store logging disabled 2012/01/18 10:12:49| Swap maxSize 0 + 262144 KB, estimated 20164 objects 2012/01/18 10:12:49| Target number of buckets: 1008 2012/01/18 10:12:49| Using 8192 Store buckets 2012/01/18 10:12:49| Max Mem size: 262144 KB 2012/01/18 10:12:49| Max Swap size: 0 KB 2012/01/18 10:12:49| Using Least Load store dir selection 2012/01/18 10:12:49| Set Current Directory to /var/spool/squid3 2012/01/18 10:12:49| Loaded Icons. 2012/01/18 10:12:49| Accepting HTTP connections at [::]:3128, FD 74. 2012/01/18 10:12:49| HTCP Disabled. 2012/01/18 10:12:49| Squid modules loaded: 0 2012/01/18 10:12:49| Adaptation support is off. 2012/01/18 10:12:49| Ready to serve requests. 2012/01/18 10:12:50| storeLateRelease: released 0 objects smb.conf # Domain Authntication Settings workgroup = <WORKGROUP> security = ads password server = <DOMAINNAME>.LOCAL realm = <DOMAINNAME>.LOCAL ldap ssl = no # logging log level = 5 max log size = 50 # logs split per machine log file = /var/log/samba/%m.log # max 50KB per log file, then rotate ; max log size = 50 # User settings username map = /etc/samba/smbusers idmap uid = 10000-20000000 idmap gid = 10000-20000000 idmap backend = ad ; template primary group = <ad group> template shell = /sbin/nologin # Winbind Settings winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind netsted groups = Yes winbind nested groups = Yes winbind cache time = 10 winbind use default domain = Yes #Other Globals unix charset = LOCALE server string = <SERVERNAME> load printers = no printing = cups cups options = raw ; printcap name = /etc/printcap #obtain list of printers automatically on SystemV ; printcap name = lpstat ; printing = cups squid.conf auth_param ntlm program /usr/bin/ntlm_auth --require-membership-of=<DOMAINNAME>\\INTERNETZ --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 10 auth_param basic program /usr/lib/squid3/squid_ldap_auth -R -b "dc=<dcname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f sAMAccountName=%s -h 192.168.15.19:3268 auth_param basic realm "Proxy Authentifizierung. Bitte geben Sie Ihren Benutzername und Ihr Passwort ein!" #means insert you PW in an other language - # external_acl_type InetGroup %LOGIN /usr/lib/squid3/squid_ldap_group -R -b "dc=<domainname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f "(&(objectclass=person)(sAMAccountName=%v) (memberof=cn=%a,cn=internetz,dc=<domainname>,dc=local))" -h 192.168.15.19:3268 auth_param negotiate program /usr/lib/squid3/squid_kerb_auth -d auth_param negotiate children 10 auth_param negotiate keep_alive on acl localnet proxy_auth REQUIRED acl InetAccess external InetGroup Internetz http_access allow InetAccess http_access deny all acl auth proxy_auth REQUIRED http_access allow auth and a very suspicious is that by adding the proxy server to the Domain i see 2 new entries in the PC one with the original computer-name leopoldine and one with leopoldine CNF:f8efa4c4-ff0e-4217-939d-f1523b43464d ?!? I tried a lot, really... but i stuck on this problem... i actually i even reinstalled all dependent programs and reconfigured them from default. Group exists and has me in it. Firefox running on the old proxy and i use IE for testing the new one. But i'll get all the time Access-Denited and to be honest i'm quite a beginner, so please don't be to prude. I'll interested in improving, i'll get the information we need to fix this but i started working 2 month ago and got only 1 1/2 year's training and not a single sec. in linux ;)

Read the article

LDAP over SSL with an EFI Fiery printer

- by austinian

I've got a printer with a Fiery running 8e Release 2. I can authenticate users against AD using the LDAP configuration, but I can only get it to work if I don't use SSL/TLS, and only if I use SIMPLE authentication. Right now, it's authenticating using a fairly low-impact user, but it's also the only system on our network that's not using LDAPS. I can get AD info fine over LDAPS using ldp.exe from my machine, our firewall, our mail filter, our linux boxes, etc. The only problem child is the Fiery. I've added the LDAP server certificate as a trusted cert to the Fiery, but after I check the box for Secure Communication and change the port to 636, pressing Validate results in a dialog box coming up saying: LDAP Validation Failed Server Name invalid or server is unavailable. I've tried changing the server name to use just the name, the FQDN, and the IP address, and changed it to another server, just to see if it was just this AD server that was fussy with the Fiery. EDIT: removed LDP output, added packet capture analysis from wireshark: The conversation seems pretty normal to me, up to the point where the Fiery terminates the connection after the server sends back a handshake response. Maybe they messed up their TLS implementation? I'm trying support, but it's been fairly useless so far. The cert is a SHA-2 (sha256RSA) 2048-bit certificate. Also, it looks like the Fiery is specifying TLS 1.0. Looking at http://msdn.microsoft.com/en-us/library/windows/desktop/aa374757(v=vs.85).aspx, I'm not seeing SHA256 and TLS 1.0 combination being supported by SChannel. headdesk perhaps that's why, after the DC changes the cipher spec, the connection is terminated by the Fiery? TLS 1.1 and 1.2 are enabled on the DC. Wireshark conversation: DC: 172.17.2.22, Fiery: 172.17.2.42 No. Time Source Source Port Destination Destination Port Protocol Length Info 1 0.000000000 172.17.2.42 48633 172.17.2.22 ldaps TCP 74 48633 > ldaps [SYN] Seq=0 Win=5840 Len=0 MSS=1460 SACK_PERM=1 TSval=3101761 TSecr=0 WS=4 2 0.000182000 Dell_5e:94:e3 Broadcast ARP 60 Who has 172.17.2.42? Tell 172.17.2.22 3 0.000369000 TyanComp_c9:0f:90 Dell_5e:94:e3 ARP 60 172.17.2.42 is at 00:e0:81:c9:0f:90 4 0.000370000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 74 ldaps > 48633 [SYN, ACK] Seq=0 Ack=1 Win=8192 Len=0 MSS=1460 WS=256 SACK_PERM=1 TSval=67970573 TSecr=3101761 5 0.000548000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=1 Ack=1 Win=5840 Len=0 TSval=3101761 TSecr=67970573 6 0.001000000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 147 Client Hello 7 0.001326000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 8 0.001513000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 9 0.001515000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=1449 Win=8736 Len=0 TSval=3101761 TSecr=67970573 10 0.001516000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=2897 Win=11632 Len=0 TSval=3101761 TSecr=67970573 11 0.001732000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 12 0.001737000 172.17.2.22 ldaps 172.17.2.42 48633 TLSv1 1243 Server Hello, Certificate, Certificate Request, Server Hello Done 13 0.001738000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=4345 Win=14528 Len=0 TSval=3101761 TSecr=67970573 14 0.001739000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=5522 Win=17424 Len=0 TSval=3101761 TSecr=67970573 15 0.002906000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 78 Certificate 16 0.004155000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 333 Client Key Exchange 17 0.004338000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5522 Ack=361 Win=66304 Len=0 TSval=67970573 TSecr=3101762 18 0.004338000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 72 Change Cipher Spec 19 0.005481000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 327 Encrypted Handshake Message 20 0.005645000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5522 Ack=628 Win=66048 Len=0 TSval=67970574 TSecr=3101762 21 0.010247000 172.17.2.22 ldaps 172.17.2.42 48633 TLSv1 125 Change Cipher Spec, Encrypted Handshake Message 22 0.016451000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [FIN, ACK] Seq=628 Ack=5581 Win=17424 Len=0 TSval=3101765 TSecr=67970574 23 0.016630000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5581 Ack=629 Win=66048 Len=0 TSval=67970575 TSecr=3101765 24 0.016811000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 60 ldaps > 48633 [RST, ACK] Seq=5581 Ack=629 Win=0 Len=0

Read the article

Connection drops while transferring large files to one server on a network

- by Charlotte

My company has two sites, each with their own LAN, using site to site VPN tunnel to connect the two sites. When transferring files (especially larger files) from site1 to site2 server1, the file transfer fails. I don't think this can be a VPN issue because transferring the same files to site2 server2 which is on the same network as server1 works fine. Pings to server1 and server2 at site2 from site1 are about the same, mostly 19/20ms with the odd one up to 50ms. As server1 is DB server with a high load I thought the NIC maybe overloaded, but a transfer from site2 server1 to site2 server2 works fine, and that uses the same NIC on server1 as transfers from site1 to site2 server1. The servers are both Windows Server 2003 VMs with VMXNET 3 NICs. Site2 Server1 route print: IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 28 9b ...... vmxnet3 Ethernet Adapter #2 0x10004 ...00 50 56 99 18 97 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.18 10 10.10.10.0 255.255.255.0 10.10.10.70 10.10.10.70 10 10.10.10.70 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.18 172.20.10.18 10 172.20.10.18 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.18 172.20.10.18 10 224.0.0.0 240.0.0.0 10.10.10.70 10.10.10.70 10 224.0.0.0 240.0.0.0 172.20.10.18 172.20.10.18 10 255.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 1 255.255.255.255 255.255.255.255 172.20.10.18 172.20.10.18 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site2 Server2 route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 15 00 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.114 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.114 172.20.10.114 10 172.20.10.114 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.114 172.20.10.114 10 224.0.0.0 240.0.0.0 172.20.10.114 172.20.10.114 10 255.255.255.255 255.255.255.255 172.20.10.114 172.20.10.114 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site1 Server route print: =========================================================================== Interface List 14...00 50 56 93 00 0b ......vmxnet3 Ethernet Adapter #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.168.1 192.168.168.118 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.168.0 255.255.255.0 On-link 192.168.168.118 261 192.168.168.118 255.255.255.255 On-link 192.168.168.118 261 192.168.168.255 255.255.255.255 On-link 192.168.168.118 261 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.168.118 261 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.168.118 261 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.168.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 261 fe80::/64 On-link 14 261 fe80::3c6b:996f:ef36:ee76/128 On-link 1 306 ff00::/8 On-link 14 261 ff00::/8 On-link =========================================================================== Persistent Routes: None tracert from site1 to site2 server1: Tracing route to server1 [172.20.10.18] over a maximum of 30 hops: 1 19 ms 19 ms 19 ms server1 [172.20.10.18] Trace complete. tracert from site2 server1 to site1: When this was run it went to the external IP of site2, then to a couple of external ips of the isp, then times out. Can anyone suggest any troubleshooting steps? Thanks, Charlotte.

Read the article

php5.4 + freebsd8.3+nginx can't get errors

- by Alexey Perepechko

I have a confusing behaviour. I can't get any error into log file or screen. I made a file index.php with content like this: "<?php a();".Normally, I will get message like this: "Call to undefined function a()" but when I called this script on my configuration I got nothing. Only white screen and empty logs. I checked all rights. I turned on all possible log file. Nothing. Please help me. My configuration is: freebsd 8.3-RELEASE PHP 5.4.7 (fpm-fcgi) nginx version: nginx/1.2.4 FPM-config [global] pid = run/php-fpm.pid error_log = log/php-fpm.log log_level = notice emergency_restart_threshold = 5 emergency_restart_interval = 2 process_control_timeout = 2 daemonize = yes events.mechanism = kqueue [puser] listen = /usr/local/www/host/tmp/php-fpm.sock; listen.backlog = -1 listen.allowed_clients = 127.0.0.1 listen.owner = puser listen.group = puser listen.mode = 0666 user = puser group = puser pm = dynamic pm.max_children = 30 pm.start_servers = 2 pm.min_spare_servers = 2 pm.max_spare_servers = 5 pm.max_requests = 50 slowlog = /usr/local/www/host/logs/fpm.log.slow request_slowlog_timeout = 1s rlimit_files = 1024 rlimit_core = 0 chroot = /usr/local/www/host/ catch_workers_output = yes env[HOSTNAME] = $HOSTNAME env[TMP] = /tmp env[TMPDIR] = /tmp env[TEMP] = /tmp php_admin_value[upload_tmp_dir] = /tmp php_admin_value[cgi.fix_pathinfo] = 0 php_admin_value[date.timezone]= 'Europe/Moscow' php_admin_value[memory_limit] = 320m php_admin_value[max_execution_time] = 180 php_admin_flag[log_errors] = on php_admin_value[error_log] = /logs/fpm-err.log php_admin_value[error_reporting] = 'E_ALL & ~E_NOTICE' php_admin_value[display_errors] = on php_admin_flag[display_startup_errors] = on NGINX config user www; worker_processes 2; worker_rlimit_nofile 80000; error_log /var/log/nginx_error.log notice; #pid logs/nginx.pid; events { worker_connections 2048; use kqueue; } http { server_tokens off; client_max_body_size 4m; include mime.types; default_type application/octet-stream; charset utf-8; sendfile on; keepalive_timeout 65; tcp_nopush on; tcp_nodelay on; log_format IP .$remote_addr.; log_format main '$remote_addr - $remote_user [$time_local] $request $request_body ' '"$status" $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; reset_timedout_connection on; server { listen 80; server_name www.example.com; access_log /usr/local/www/host/logs/access.log main; error_log /usr/local/www/host/logs/error.log error; error_page 500 502 503 504 /errors/50x.html; error_page 404 /errors/404.html; root /usr/local/www/host/htdocs; index index.php index.html index.htm; location / { index index.html index.php; try_files $uri /index.php?$args; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(.*)$; fastcgi_intercept_errors on; fastcgi_pass unix:/usr/local/www/host/tmp/php-fpm.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /htdocs$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_path_info; fastcgi_param PATH_TRANSLATED /htdocs$fastcgi_script_name; include /usr/local/etc/nginx/fastcgi_params; } } } PHP config (php.ini) [PHP] engine = On short_open_tag = On asp_tags = Off precision = 14 y2k_compliance = On output_buffering = 4096 zlib.output_compression = Off implicit_flush = Off unserialize_callback_func = serialize_precision = 100 allow_call_time_pass_reference = Off safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH disable_functions = dl,system,exec,passthru,shell_exec disable_classes = expose_php = On max_execution_time = 30 max_input_time = 60 memory_limit = 128M error_reporting = E_ALL display_errors = On display_startup_errors = On log_errors = On log_errors_max_len = 1024 ignore_repeated_errors = Off ignore_repeated_source = Off report_memleaks = On track_errors = On error_log = /var/log/php-fpm-error.log variables_order = "GPCS" request_order = "GP" register_globals = Off register_long_arrays = Off register_argc_argv = Off auto_globals_jit = On post_max_size = 8M magic_quotes_gpc = Off magic_quotes_runtime = Off magic_quotes_sybase = Off auto_prepend_file = auto_append_file = default_mimetype = "text/html" doc_root = user_dir = enable_dl = Off file_uploads = On upload_max_filesize = 2M max_file_uploads = 20 allow_url_fopen = On allow_url_include = Off default_socket_timeout = 60 [Date] date.timezone = Europe/Moscow [filter] [iconv] [intl] [sqlite] [sqlite3] [Pcre] [Pdo] [Pdo_mysql] [Phar] [Syslog] define_syslog_variables = Off [mail function] SMTP = localhost smtp_port = 25 mail.add_x_header = On [SQL] sql.safe_mode = Off [ODBC] odbc.allow_persistent = On odbc.check_persistent = On odbc.max_persistent = -1 odbc.max_links = -1 odbc.defaultlrl = 4096 odbc.defaultbinmode = 1 [Interbase] [MySQL] mysql.allow_local_infile = On mysql.allow_persistent = On mysql.cache_size = 2000 mysql.max_persistent = -1 mysql.max_links = -1 mysql.default_port = mysql.default_socket = mysql.default_host = mysql.default_user = mysql.default_password = mysql.connect_timeout = 60 mysql.trace_mode = Off [MySQLi] mysqli.max_persistent = -1 mysqli.allow_persistent = On mysqli.max_links = -1 mysqli.cache_size = 2000 mysqli.default_port = 3306 mysqli.default_socket = mysqli.default_host = mysqli.default_user = mysqli.default_pw = mysqli.reconnect = Off [mysqlnd] mysqlnd.collect_statistics = On mysqlnd.collect_memory_statistics = Off [OCI8] [PostgresSQL] pgsql.allow_persistent = On pgsql.auto_reset_persistent = Off pgsql.max_persistent = -1 pgsql.max_links = -1 pgsql.ignore_notice = 0 pgsql.log_notice = 0 [Sybase-CT] sybct.allow_persistent = On sybct.max_persistent = -1 sybct.max_links = -1 sybct.min_server_severity = 10 sybct.min_client_severity = 10 [bcmath] bcmath.scale = 0 [browscap] [Session] session.save_handler = files session.use_cookies = 1 session.use_only_cookies = 1 session.name = PHPSESSID session.auto_start = 0 session.cookie_lifetime = 0 session.cookie_path = / session.cookie_domain = session.cookie_httponly = session.serialize_handler = php session.gc_probability = 1 session.gc_divisor = 1000 session.gc_maxlifetime = 1440 session.bug_compat_42 = Off session.bug_compat_warn = Off session.referer_check = session.entropy_length = 0 session.cache_limiter = nocache session.cache_expire = 180 session.use_trans_sid = 0 session.hash_function = 0 session.hash_bits_per_character = 5 url_rewriter.tags = "a=href,area=href,frame=src,input=src,form=fakeentry" [MSSQL] mssql.allow_persistent = On mssql.max_persistent = -1 mssql.max_links = -1 mssql.min_error_severity = 10 mssql.min_message_severity = 10 mssql.compatability_mode = Off mssql.secure_connection = Off [Assertion] [COM] [mbstring] [gd] [exif] [Tidy] tidy.clean_output = Off [soap] soap.wsdl_cache_enabled=1 soap.wsdl_cache_dir="/tmp" soap.wsdl_cache_ttl=86400 soap.wsdl_cache_limit = 5 [sysvshm] [ldap] ldap.max_links = -1 [mcrypt] [dba] I need to get errors on display and detailed record in the error.log.

Read the article

Installing Windows on HP Proliant Servers without SmartStart

- by Fitzroy

I have a PXE server for deploying Windows XP and Windows 7 to workstations. The process is as follows: Boot the workstation from the NIC. Workstation sends a DHCP request. DHCP server responds with an IP address and the location of the PXE server. Workstation downloads WinPE image file from PXE server via TFTP Workstation stores WinPE image file in memory and executes it. Once booted into WinPE, I connect to a network share to gain access to either the Windows XP or Windows 7 installation files. A custom script is launched to guide you through the process of formatting and partitioning the hard drive(s) (using DISKPART and FORMAT). Another custom script asks for details such as the hostname to assign to the workstation. The answers provided are used to build an unattended answer file (SIF [Setup Information File] for WinXP and XML for Win7). The Windows setup EXE is launched, passing the unattended answer file to it as a parameter. The Windows XP and Windows 7 installation sources have been customised to include the drivers for our Dell workstations. They also run a number of scripts upon first booting up to install software packages. This process works very well for our workstations and I would now like to use it for building our servers too. The vast majority of our servers are HP Proliant DL360 G6, DL380 G5 and DL380 G6. They’re running Windows Server 2003 (various editions) or 2008 (various editions). To date, we have always built the HP Proliant servers using the SmartStart CD provided. SmartStart does three useful things for us: Setup RAID with HP Array Configuration Utility (ACU). Installs and configures SNMP Installs various HP Tools for Windows (HP Array Configuration Utility, HP Array Diagnostic Utility, HP Proliant Integrated Management Log Viewer, etc) Using SmartStart I have never had to manually download and install Windows drivers for network, sound, video, etc. I'm not sure if this is because SmartStart copies drivers from the CD during setup, or whether Windows just has the drivers natively in its driver CAB. If I abandon the SmartStart CD in favour of my PXE server I would have to do the following: As I wont have access to ACU, I'll configure the RAID (before booting to the PXE server) by pressing F8 (during the boot process) to access Option ROM Configuration for Arrays (ORCA). Installation of SNMP and the HP Tools will have to be installed once the Windows installation is complete using the Proliant Support Pack. Is this method OK? Is there anything that the SmartStart CD does that I'll be unable to do by other means? Are there any disadvantages to not using the SmartStart CD? Many thanks. UPDATE 05/01/12 I’ve been reading through the SmartStart Scripting Toolkit documentation. The scripting toolkit contains command line tools which work within WinPE and can such things as configure BIOS settings, configure an array and setup ILO. I’m personally not too bothered about configuring BIOS settings as I rarely deviate from the defaults (unless the server is to be a Hyper-V host). I’m not too fussed about being able to configure the array from within WinPE, as I’m happy to just press F8 and use Option ROM Configuration for Arrays (ORCA). Although, if it’s easy enough to do, I will explore this further, as it saves time if everything can be configured from within WinPE. One of the nice features all the tools possess is that you can pass input files to them. EG. Configure one server to your requirements, capture its configuration to a file (using the appropriate tool), you can then use the tool on other servers passing the input file with the captured configuration. Array controller drivers appear to be included with the toolkit along with example of how to incorporate them within a WinPE build. I suppose WinPE won’t be able to see logical volumes (I.E 2x physical disks in a RAID 1 configuration) without the array controller drivers? I mentioned in my post that SmartStart normally installs a bunch of Windows HP tools for you. I’ve had a look today, and if you run the SmartStart CD from within Windows all the tools can be installed. Therefore I can do this after the Windows installation is complete. The SmartStart CD appears to contain a lot Windows drivers. I can customise my Windows 2008 source to incorporate these drivers. However, I understand that incorporating an array controller driver is a little different to most drivers. I believe that you have to provide the driver during the very early stages of the Windows setup. I’m working through the Scripting Toolkit documentation to try and work this out...

Read the article

nginx+php-fpm help optimize configs

- by Dmitro

I have 3 servers. First server (CPU - model name: 06/17, 2.66GHz, 4 cores, 8GB RAM) have nginx as load balancer with next config upstream lb_mydomain { server mydomain.ru:81 weight=2; server 66.0.0.18 weight=6; } server { listen 80; server_name ~(?!mydomain.ru)(.*); client_max_body_size 20m; location / { proxy_pass http://lb_mydomain; proxy_redirect off; proxy_set_header Connection close; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass_header Set-Cookie; proxy_pass_header P3P; proxy_pass_header Content-Type; proxy_pass_header Content-Disposition; proxy_pass_header Content-Length; } } And configs from nginx.conf: user www-data; worker_processes 5; # worker_priority -1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 5024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; default_type application/octet-stream; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; # PHP-FPM (backend) upstream php-fpm { server 127.0.0.1:9000; } include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } And config php-fpm: listen = 127.0.0.1:9000 ;listen.backlog = -1 ;listen.allowed_clients = 127.0.0.1 ;listen.owner = www-data ;listen.group = www-data ;listen.mode = 0666 user = www-data group = www-data pm = dynamic pm.max_children = 80 ;pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 ;pm.max_requests = 500 pm.status_path = /status ping.path = /ping ;ping.response = pong request_terminate_timeout = 30s request_slowlog_timeout = 10s slowlog = /var/log/php-fpm.log.slow ;rlimit_files = 1024 ;rlimit_core = 0 ;chroot = chdir = /var/www ;catch_workers_output = yes ;env[HOSTNAME] = $HOSTNAME ;env[PATH] = /usr/local/bin:/usr/bin:/bin ;env[TMP] = /tmp ;env[TMPDIR] = /tmp ;env[TEMP] = /tmp ;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f [email protected] ;php_flag[display_errors] = off ;php_admin_value[error_log] = /var/log/fpm-php.www.log ;php_admin_flag[log_errors] = on ;php_admin_value[memory_limit] = 32M In top I see 20 php-fpm processes which use from 1% - 15% CPU. So it's have high load averadge: top - 15:36:22 up 34 days, 20:54, 1 user, load average: 5.98, 7.75, 8.78 Tasks: 218 total, 1 running, 217 sleeping, 0 stopped, 0 zombie Cpu(s): 34.1%us, 3.2%sy, 0.0%ni, 37.0%id, 24.8%wa, 0.0%hi, 0.9%si, 0.0%st Mem: 8183228k total, 7538584k used, 644644k free, 351136k buffers Swap: 9936892k total, 14636k used, 9922256k free, 990540k cached Second server(CPU - model name: Intel(R) Xeon(R) CPU E5504 @ 2.00GHz, 8 cores, 8GB RAM). Nginx configs from nginx.conf: user www-data; worker_processes 5; # worker_priority -1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 5024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; default_type application/octet-stream; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; # PHP-FPM (backend) upstream php-fpm { server 127.0.0.1:9000; } include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } And config of php-fpm: listen = 127.0.0.1:9000 ;listen.backlog = -1 ;listen.allowed_clients = 127.0.0.1 ;listen.owner = www-data ;listen.group = www-data ;listen.mode = 0666 user = www-data group = www-data pm = dynamic pm.max_children = 50 ;pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 ;pm.max_requests = 500 ;pm.status_path = /status ;ping.path = /ping ;ping.response = pong ;request_terminate_timeout = 0 ;request_slowlog_timeout = 0 ;slowlog = /var/log/php-fpm.log.slow ;rlimit_files = 1024 ;rlimit_core = 0 ;chroot = chdir = /var/www ;catch_workers_output = yes ;env[HOSTNAME] = $HOSTNAME ;env[PATH] = /usr/local/bin:/usr/bin:/bin ;env[TMP] = /tmp ;env[TMPDIR] = /tmp ;env[TEMP] = /tmp ;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f [email protected] ;php_flag[display_errors] = off ;php_admin_value[error_log] = /var/log/fpm-php.www.log ;php_admin_flag[log_errors] = on ;php_admin_value[memory_limit] = 32M In top I see 50 php-fpm processes which use from 10% - 25% CPU. So it's have high load averadge: top - 15:53:05 up 33 days, 1:15, 1 user, load average: 41.35, 40.28, 39.61 Tasks: 239 total, 40 running, 199 sleeping, 0 stopped, 0 zombie Cpu(s): 96.5%us, 3.1%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.4%si, 0.0%st Mem: 8185560k total, 7804224k used, 381336k free, 161648k buffers Swap: 19802108k total, 16k used, 19802092k free, 5068112k cached Third server is server with database postgresql. Also i try ab -n 50 -c 5 http://www.mydomain.ru/ And I get next info: Complete requests: 50 Failed requests: 48 (Connect: 0, Receive: 0, Length: 48, Exceptions: 0) Write errors: 0 Total transferred: 9271367 bytes HTML transferred: 9247767 bytes Requests per second: 1.02 [#/sec] (mean) Time per request: 4882.427 [ms] (mean) Time per request: 976.486 [ms] (mean, across all concurrent requests) Transfer rate: 185.44 [Kbytes/sec] received Please advise how can I make lower level of load average?

Read the article

Reverse lookup SERVFAIL

- by Quan Tran

I just set up a DNS server and a web server using Virtualbox. The IP address of the DNS server is 192.168.56.101 and the web server 192.168.56.102. Here are my configuration files for the DNS server: named.conf: // // named.conf // // Provided by Red Hat bind package to configure the ISC BIND named(8) DNS // server as a caching only nameserver (as a localhost DNS resolver only). // // See /usr/share/doc/bind*/sample/ for example named configuration files. // options { directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; //query-source address * port 53; //forward first; forwarders { 8.8.8.8; 8.8.4.4; }; listen-on port 53 { 127.0.0.1; 192.168.56.0/24; }; allow-query { localhost; 192.168.56.0/24; }; recursion yes; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; managed-keys-directory "/var/named/dynamic"; }; logging { channel default_debug { file "data/named.run"; severity debug 10; print-category yes; print-time yes; print-severity yes; }; }; zone "quantran.com" in { type master; file "named.quantran.com"; }; zone "56.168.192.in-addr.arpa" in { type master; file "named.192.168.56"; allow-update { none; }; }; include "/etc/named.rfc1912.zones"; include "/etc/named.root.key"; named.quantran.com: $TTL 86400 quantran.com. IN SOA dns1.quantran.com. root.quantran.com. ( 100 ; serial 3600 ; refresh 600 ; retry 604800 ; expire 86400 ) IN NS dns1.quantran.com. dns1.quantran.com. IN A 192.168.56.101 www.quantran.com. IN A 192.168.56.102 named.192.168.56: $TTL 86400 $ORIGIN 56.168.192.in-addr.arpa. @ IN SOA dns1.quantran.com. root.quantran.com. ( 100 ; serial 3600 ; refresh 600 ; retry 604800 ; expire 86400 ) ; minimum IN NS dns1.quantran.com. 101.56.168.192.in-addr.arpa. IN PTR dns1.quantran.com. 102 IN PTR www.quantran.com. When I try a normal lookup from the host (I configured so that the only nameserver the host uses is the DNS server 192.168.56.101): quan@quantran:~$ host www.quantran.com www.quantran.com has address 192.168.56.102 quan@quantran:~$ host dns1.quantran.com dns1.quantran.com has address 192.168.56.101 But when I try a reverse lookup: quan@quantran:~$ host -v 192.168.56.101 192.168.56.101 Trying "101.56.168.192.in-addr.arpa" Using domain server: Name: 192.168.56.101 Address: 192.168.56.101#53 Aliases: Host 101.56.168.192.in-addr.arpa not found: 2(SERVFAIL) Received 45 bytes from 192.168.56.101#53 in 0 ms quan@quantran:~$ host -v 192.168.56.102 192.168.56.101 Trying "102.56.168.192.in-addr.arpa" Using domain server: Name: 192.168.56.101 Address: 192.168.56.101#53 Aliases: Host 102.56.168.192.in-addr.arpa not found: 2(SERVFAIL) Received 45 bytes from 192.168.56.101#53 in 0 ms So why can't I perform a reverse lookup? Anything wrong with the zone configuration files? Thanks in advance :) Oh, here is the output from the log file /var/named/data/named.run when I perform the reverse lookup: quan@quantran:~$ host 192.168.56.102 192.168.56.101 Using domain server: Name: 192.168.56.101 Address: 192.168.56.101#53 Aliases: Host 102.56.168.192.in-addr.arpa not found: 2(SERVFAIL) /var/named/data/named.run: 02-Jun-2014 15:18:11.950 client: debug 3: client 192.168.56.1#51786: UDP request 02-Jun-2014 15:18:11.950 client: debug 5: client 192.168.56.1#51786: using view '_default' 02-Jun-2014 15:18:11.950 security: debug 3: client 192.168.56.1#51786: request is not signed 02-Jun-2014 15:18:11.950 security: debug 3: client 192.168.56.1#51786: recursion available 02-Jun-2014 15:18:11.950 client: debug 3: client 192.168.56.1#51786: query 02-Jun-2014 15:18:11.950 client: debug 10: client 192.168.56.1#51786: ns_client_attach: ref = 1 02-Jun-2014 15:18:11.950 query-errors: debug 1: client 192.168.56.1#51786: query failed (SERVFAIL) for 102.56.168.192.in-addr.arpa/IN/PTR at query.c:5428 02-Jun-2014 15:18:11.950 client: debug 3: client 192.168.56.1#51786: error 02-Jun-2014 15:18:11.950 client: debug 3: client 192.168.56.1#51786: send 02-Jun-2014 15:18:11.950 client: debug 3: client 192.168.56.1#51786: sendto 02-Jun-2014 15:18:11.951 client: debug 3: client 192.168.56.1#51786: senddone 02-Jun-2014 15:18:11.951 client: debug 3: client 192.168.56.1#51786: next 02-Jun-2014 15:18:11.951 client: debug 10: client 192.168.56.1#51786: ns_client_detach: ref = 0 02-Jun-2014 15:18:11.951 client: debug 3: client 192.168.56.1#51786: endrequest 02-Jun-2014 15:18:11.951 client: debug 3: client @0xb537e008: udprecv Also, I made some changes to the log section in named.conf.

Read the article

CARP: two machines think they're the master, but only on one interface

- by Conor McDermottroe

I have two machines, each configured identically as a firewall/load balancer for a busy website. I have set them up with CARP and pfsync on both the internal and external interfaces. The internal interface is behaving as expected (primary listed as MASTER and secondary listed as BACKUP) On both machines, the network interfaces are as follows: em0 - External interface bge0 - Internal interface bge1 - Crossover connection between both machines carp0 - Shared external interface for CARP carp1 - Shared internal interface for CARP I've rewritten the IP addresses and MAC addresses below. The networks are as follows: 10.0.1.0/24 - External network 10.0.2.0/24 - Internal network 10.0.3.0/24 - Crossover network Here's the output from ifconfig on the primary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.10 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.10 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.10 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.11 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 0 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: MASTER vhid 2 advbase 1 advskew 0 And here's the /etc/rc.conf excerpt from the primary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.10 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.11" And here's the output on the secondary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.11 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.11 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.11 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.10 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 20 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: BACKUP vhid 2 advbase 1 advskew 20 And here's the /etc/rc.conf excerpt from the secondary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.11 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] advskew 20 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] advskew 20 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.10" What I don't understand is, the carp status on carp0 is MASTER on both machines when the status on carp1 is as it should be (MASTER on the primary and BACKUP on the secondary). What am I missing? Where should I be looking for clues?

Read the article

Windows XP periodically disconnects, reconnects; Windows 7 doesn't

- by einpoklum

My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it doesn't happen. The connection is smooth (OS is sluggish though, but never mind that). Like I said, I updated the NIC driver. I tried reducing the MTU (used something called Dr. TCP), thinking maybe that would help, but it didn't. (I'm a bit but not super-knowledgeable about TCP parameters.) I'm guessing it's either a problem with the driver or some settings which are different between the two OSes. ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM

Read the article

Nginx no longer servers uwsgi application behind HAProxy - Looks for static file instead

- by Ralph

We implemented our web application using web2py. It consists of several modules offering a REST API at various resources (e.g. /dids, /replicas, ...). The API is used by clients implementing requests.py. My problem is that our web app works fine if it's behind HAProxy and hosted by Apache using mod_wsgi. It also works fine if the clients interact with nginx directly. It doesn't work though when using HAProxy in front of nginx. My guess is that HAProxy somehow modifies the request and thus nginx behaves differently i.e. looking for a static file instead of calling the WSGI container. Unfortunately I can't figure out what's exactly going (wr)on(g). Here are the relevant config sections of these three component's config files. At least I guess they are interesting. If you miss anything, please let me know. 1) haproxy.conf frontend app-lb bind loadbalancer:443 ssl crt /etc/grid-security/hostcertkey.pem default_backend nginx-servers mode http backend nginx-servers balance leastconn option forwardfor server nginx-01 nginx-server-int-01.domain.com:80 check 2) nginx.conf: sendfile off; #tcp_nopush on; keepalive_timeout 65; include /etc/nginx/conf.d/*.conf; server { server_name nginx-server-int-01.domain.com; root /path/to/app/; location / { uwsgi_pass unix:///tmp/app.sock; include uwsgi_params; uwsgi_read_timeout 600; # Requests can run for a serious long time } 3) uwsgi.ini [uwsgi] chdir = /path/to/app/ chmod-socket = 777 no-default-app = True socket = /tmp/app.sock manage-script-name = True mount = /dids=did.py mount = /replicas=replica.py callable = application Now when I let my clients go against nginx-server-int-01.domain.com everything is fine. In the access.log of nginx lines like these are appearing: 128.142.XXX.XX0 - - [23/Aug/2014:01:29:20 +0200] "POST /dids/attachments HTTP/1.1" 201 17 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:20 +0200] "POST /dids/attachments HTTP/1.1" 201 17 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:20 +0200] "POST /dids/user.ogueta/cnt_mc12_8TeV.16304.stream_name_too_long.other.notype.004202218365415e990b9997ea859f20.user/dids HTTP/1.1" 201 17 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:20 +0200] "POST /replicas/list HTTP/1.1" 200 5282 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:20 +0200] "POST /replicas/list HTTP/1.1" 200 5094 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:20 +0200] "POST /replicas/list HTTP/1.1" 200 528 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:21 +0200] "GET /dids/mc13_14TeV/dids/search?project=mc13_14TeV&stream_name=%2Adummy&type=dataset&datatype=NTUP_SMDYMUMU HTTP/1.1" 401 73 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:21 +0200] "POST /replicas/list HTTP/1.1" 200 713 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" 128.142.XXX.XX0 - - [23/Aug/2014:01:29:21 +0200] "POST /dids/attachments HTTP/1.1" 201 17 "-" "python-requests/2.3.0 CPython/2.6.6 Linux/2.6.32-358.23.2.el6.x86_64" "-" But when I switch the clients to go against HAProxy (loadbalancer.domain.com:443), the error.log of nginx shows lines like these: 2014/08/23 01:26:01 [error] 1705#0: *21231 open() "/usr/share/nginx/html/dids/attachments" failed (2: No such file or directory), client: 128.142.XXX.XX1, server: localhost, request: "POST /dids/attachments HTTP/1.1", host: "loadbalancer.domain.com" 2014/08/23 01:26:02 [error] 1705#0: *21232 open() "/usr/share/nginx/html/replicas/list" failed (2: No such file or directory), client: 128.142.XXX.XX1, server: localhost, request: "POST /replicas/list HTTP/1.1", host: "loadbalancer.domain.com" 2014/08/23 01:26:02 [error] 1705#0: *21233 open() "/usr/share/nginx/html/dids/attachments" failed (2: No such file or directory), client: 128.142.XXX.XX1, server: localhost, request: "POST /dids/attachments HTTP/1.1", host: "loadbalancer.domain.com" 2014/08/23 01:26:02 [error] 1705#0: *21234 open() "/usr/share/nginx/html/replicas/list" failed (2: No such file or directory), client: 128.142.XXX.XX1, server: localhost, request: "POST /replicas/list HTTP/1.1", host: "loadbalancer.domain.com" 2014/08/23 01:26:02 [error] 1705#0: *21235 open() "/usr/share/nginx/html/dids/attachments" failed (2: No such file or directory), client: 128.142.XXX.XXX, server: localhost, request: "POST /dids/attachments HTTP/1.1", host: "loadbalancer" 2014/08/23 01:26:02 [error] 1705#0: *21238 open() "/usr/share/nginx/html/replicas/list" failed (2: No such file or directory), client: 128.142.XXX.XXX, server: localhost, request: "POST /replicas/list HTTP/1.1", host: "loadbalancer.domain.com" 2014/08/23 01:26:02 [error] 1705#0: *21239 open() "/usr/share/nginx/html/dids/attachments" failed (2: No such file or directory), client: 128.142.XXX.XXX, server: localhost, request: "POST /dids/attachments HTTP/1.1", host: "loadbalancer.domain.com" 2014/08/23 01:26:02 [error] 1705#0: *21242 open() "/usr/share/nginx/html/replicas/list" failed (2: No such file or directory), client: 128.142.XXX.XXX, server: localhost, request: "POST /replicas/list HTTP/1.1", host: "loadbalancer.domain.com" 2014/08/23 01:26:02 [error] 1705#0: *21244 open() "/usr/share/nginx/html/dids/attachments" failed (2: No such file or directory), client: 128.142.XXX.XXX, server: localhost, request: "POST /dids/attachments HTTP/1.1", host: "loadbalancer.domain.com" As you can see, that request looks the same, only the client IP changed, from the client's host to the one from loadbalancer.domain.com. But due to what ever reasons ngxin seems to assume that it is a static file to be served which eventually results in the file not found message. I searched the web for multiple hours already, but without much luck so far. Any help is very much appreciated. Cheers, Ralph

Read the article

How to restart RoR services after server has been rebooted

- by Alan DeLonga

Update I have been searching around to see what services would possibly need to be restarted in my project after reboot. One of them was thinking sphinx, which I finally got to the point where it logs: [Fri Nov 16 19:34:29.820 2012] [29623] accepting connections But I still cant run searchd or searchd --stop because there was no generated sphinx.conf file in the etc/sphinxsearch for more info refer to this open thread on thinking_sphinx after reboot I then turned to looking into restarting unicorn or thin based on some insight I got. The issue is when I check my gems I see one for thin AND unicorn. But when I try to start either one of them they have no file residing in etc/init.d/ where the nginx and sphinxsearch files reside... Would rebooting totally erase the files for an app server like thin or unicorn? We are hosted on Rackspace running ruby 1.9.2p290 rails (3.2.8, 3.2.7, 3.2.0) nginx/1.1.19 notice that there are gems for unicorn and thin but there is no unicorn.rb or thin.rb in my config folder for my app... I am still super lost if any one can give me some insight on some steps to take to figure this out I would really appreciate it. Anything would help, thanks for reading. thin 1.4.1 unicorn 4.3.1 When I run unicorn I get the same issue as referenced here : > /usr/local/bin/unicorn start /usr/local/lib/ruby/gems/1.9.1/gems/unicorn-4.3.1/lib/unicorn/configurator.rb:610:in `parse_rackup_file': rackup file (start) not readable (ArgumentError) from /usr/local/lib/ruby/gems/1.9.1/gems/unicorn-4.3.1/lib/unicorn/configurator.rb:76:in `reload' from /usr/local/lib/ruby/gems/1.9.1/gems/unicorn-4.3.1/lib/unicorn/configurator.rb:67:in `initialize' from /usr/local/lib/ruby/gems/1.9.1/gems/unicorn-4.3.1/lib/unicorn/http_server.rb:104:in `new' from /usr/local/lib/ruby/gems/1.9.1/gems/unicorn-4.3.1/lib/unicorn/http_server.rb:104:in `initialize' from /usr/local/lib/ruby/gems/1.9.1/gems/unicorn-4.3.1/bin/unicorn:121:in `new' from /usr/local/lib/ruby/gems/1.9.1/gems/unicorn-4.3.1/bin/unicorn:121:in `<top (required)>' from /usr/local/bin/unicorn:19:in `load' from /usr/local/bin/unicorn:19:in `<main>' When I run thin it just opens a command line prompt... /usr/local/bin/thin start >> Using rack adapter Other gems: * LOCAL GEMS * actionmailer (3.2.8, 3.2.7, 3.2.0) actionpack (3.2.8, 3.2.7, 3.2.0) activemodel (3.2.8, 3.2.7, 3.2.0) activerecord (3.2.8, 3.2.7, 3.2.0) activeresource (3.2.8, 3.2.7, 3.2.0) activesupport (3.2.8, 3.2.7, 3.2.0) arel (3.0.2) builder (3.0.0) bundler (1.1.5) carmen (1.0.0.beta2) carmen-rails (1.0.0.beta3) cocaine (0.2.1) coffee-rails (3.2.2) coffee-script (2.2.0) coffee-script-source (1.3.3) daemons (1.1.9) erubis (2.7.0) eventmachine (0.12.10) execjs (1.4.0) faraday (0.8.4) faraday_middleware (0.8.8) foursquare2 (1.8.2) geokit (1.6.5) hashie (1.2.0) hike (1.2.1) httparty (0.8.3) httpauth (0.1) i18n (0.6.0) journey (1.0.4) jquery-rails (2.0.2) json (1.7.4, 1.7.3) jwt (0.1.5) kgio (2.7.4) lastfm (1.8.0) libv8 (3.3.10.4 x86_64-linux) mail (2.4.4) mime-types (1.19, 1.18) minitest (1.6.0) multi_json (1.3.6) multi_xml (0.5.1) multipart-post (1.1.5) mysql2 (0.3.11) oauth2 (0.8.0) paperclip (3.1.1) polyglot (0.3.3) rack (1.4.1) rack-cache (1.2) rack-ssl (1.3.2) rack-test (0.6.1) rails (3.2.8, 3.2.7, 3.2.0) railties (3.2.8, 3.2.7, 3.2.0) raindrops (0.10.0, 0.9.0) rake (0.9.2.2, 0.8.7) rdoc (3.12, 2.5.8) riddle (1.5.3) sass (3.2.0, 3.1.19) sass-rails (3.2.5) sprockets (2.1.3) sqlite3 (1.3.6) sqlite3-ruby (1.3.3) therubyracer (0.10.2, 0.10.1) thin (1.4.1) thinking-sphinx (2.0.10) thor (0.16.0, 0.15.4, 0.14.6) tilt (1.3.3) treetop (1.4.10) tzinfo (0.3.33) uglifier (1.2.7, 1.2.4) unicorn (4.3.1) xml-simple (1.1.1) I am working on a project that was built by another group. I made some modifications to a constants file in the config folder (changing some values for arrays that populated some drop down fields), but the app had to be rebooted before those changes would be recognized. The hosting is through Rackspace, we rebooted through the option on their site. I contacted them and checked the status of our server, the port is open and operational. The problem is the app is not running when you go to the address for the site. Then when I put in the ip address of the server it just says "Welcome to Nginx". But in a log files I see: [Thu Nov 15 02:34:37.945 2012] [15916] caught SIGTERM, shutting down [Thu Nov 15 02:34:37.996 2012] [15916] shutdown complete I am not very versed in server side set up. I have also never worked on a Rails project that had to have specific services started before the application will start. Any insight as to how to figure out what services need to be restarted and how to go about restarting them would be greatly appreciated. I feel kind of dead in the water at this point... Thanks, Alan

Read the article

Deployment Workbench no longer available after PXE boot

- by Patrick

Our build process revolves around windows Deployment Workbench. Unfortunately this was setup by someone who is no longer with the company, and no-one has ever dared/needed to make any changes. The other day it stopped working. It turns out that one of our build guys started thinking about changing some stuff in it, clicked something and now it no longer works (He is saying now that he right clicked on the 'LAB' entry in 'Deployment points' and hit 'Update', which took some time to run through apparently). The job has fallen on me to resolve and frankly I'm not sure what I'm doing. I was wondering if someone with more experience than me can provide some pointers as to troubleshooting cos I'm feeling quite a lot in the dark here. On the server I have Deployment Workbench up and running (MMC snapin) version 3.0. There is a WDS service that appears to be running ok, as does the tFTPd service. Nothing specific to this in event logs. From the client side; PXE boot works and gets you to the Win PE launch, and it has the correct company logo as the background (proving to me that its loading win PE from the network). WPEINIT runs, and asks for domain credentials, here the team simply put User/Pass/Domain in the boxes and click ok. Normally the build would kick off. Instead they get an error message saying that the \NATBLU01\Distribution$ share isn't available. Checking \NATBLU01\Distribution$ shows that its there and accessible over the network. Security/permissions seem ok, even 'ANONYMOUS LOGON' has read access to that share so I don't see that being a problem. Digging the trace files from C:\MININT\SMSOSD\OSDLOGS\ after an attempt to run the build I can see an error saying much the same - <![LOG[Validating connection to \\NATBLU01\Distribution$]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[FindFile: The file OSDConnectToUNC.exe could not be found in any standard locations.]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[The network location cannot be reached. For information about network troubleshooting, see Windows Help.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> <![LOG[ERROR - Unable to map a network drive to \\NATBLU01\Distribution$.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> BDD.LOG shows much the same. Full copies of the .LOG files can both files be found here : BDD.LOG LITETOUCH.LOG I can get to a command prompt from the Win PE that boots from PXE, however there isn't any network stuff there. IPCONFIG returns nothing so none of the tests I would usually run resolve anything. I'm at a loss frankly. I did wonder if I could perhaps start a new build process but if the change to the DeploymentWorkbench has knocked it offline I don't think I'm going to be able to create a new deployment. Failing that; we do have a deployment point labeled type 'Media' which appears to be a DVD ISO image of one of the builds, but its dated 2008, is it possible to export the network build to .ISO and build from DVD? We are looking at new hardware to run this from anyway (for the impending Windows 7 roll out) so a temporary work round isn't going to be too much of a problem. All assistance is appreciated! EDIT : OK. Got it working again. Solution was close to Newmanth's idea. The problem was that our PE image didn't appear to be connecting the network. I had an older copy of the PE boot.WIM on a stick that I had been using for other purposes. I booted that and correctly got a network connection. Showed a correct internal IP and could ping out etc etc. However I was still getting the same errors in all the logs and in when wpeinit was running. What I did seperately was to update the PE image that DeploymentWorkbench was pushing out to display a different back ground. I wanted to prove that I was working in the correct place. Turns out that I wasn't. I went and looked at the other deployment stuff we had on this machine, Windows Deployment Services was installed and although all the install images are off line the boot image was online, so I uploaded the copy from my stick to that. Booted straight off. And fixed. Working. Yay! For anyone stumbling across this in the future you may find that although your deployment images are located in the DeploymentWorkbench, the Win PE boot image you are launching from is located in the associated Windows Deployment Services images.

Read the article

Can connect to Samba, but access denied to homes

- by user893730

I can connect to the samba server using both IP address and server name, and I can see the home folder name, but can't connect to it smb.cnf [global] workgroup = WORKGROUP server string = Venus wins support = no read only = no browsable = yes create mode = 0777 directory mode = 0777 case sensitive = no dns proxy = no interfaces = 127.0.0.1/8 eth0 bind interfaces only = yes log file = /var/log/samba/log.%m max log size = 1000 syslog = 0 security = user encrypt passwords = true passdb backend = smbpasswd obey pam restrictions = yes unix password sync = no passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = no [homes] comment = User Directories path = /data/localdevs/%u public = no browsable = yes writable = yes the /etc/samba folder has the following files in it lmhosts smb.conf smb.conf.orig smbusers The output of "sudo pdbedit -L" is user1:500: ls -abl /data/localdevs/ drwxr-xr-x. 4 user1 user1 4096 Jul 24 17:35 user1 These are what samba logs are showing when I get the access denied to user1's home directory [2012/07/24 20:27:08.599216, 3] smbd/process.c:1489(process_smb) Transaction 24 of length 90 (0 toread) [2012/07/24 20:27:08.599350, 3] smbd/process.c:1298(switch_message) switch message SMBntcreateX (pid 2440) conn 0x7f6758780c00 [2012/07/24 20:27:08.599373, 4] smbd/uid.c:257(change_to_user) change_to_user: Skipping user change - already user [2012/07/24 20:27:08.599412, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.599485, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.599508, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.599552, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.599581, 3] smbd/dosmode.c:166(unix_mode) unix_mode(.) returning 0766 [2012/07/24 20:27:08.599643, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.599668, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.599707, 4] smbd/open.c:1990(open_file_ntcreate) calling open_file with flags=0x0 flags2=0x0 mode=0766, access_mask = 0x81, open_access_mask = 0x81 [2012/07/24 20:27:08.599806, 3] smbd/open.c:467(open_file) Error opening file . (NT_STATUS_ACCESS_DENIED) (local_flags=0) (flags=0) [2012/07/24 20:27:08.599838, 3] smbd/error.c:80(error_packet_set) error packet at smbd/error.c(160) cmd=162 (SMBntcreateX) NT_STATUS_ACCESS_DENIED [2012/07/24 20:27:08.604075, 3] smbd/process.c:1489(process_smb) Transaction 25 of length 90 (0 toread) [2012/07/24 20:27:08.604193, 3] smbd/process.c:1298(switch_message) switch message SMBntcreateX (pid 2440) conn 0x7f6758780c00 [2012/07/24 20:27:08.604216, 4] smbd/uid.c:257(change_to_user) change_to_user: Skipping user change - already user [2012/07/24 20:27:08.604268, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.604336, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.604395, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.604419, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.604442, 3] smbd/dosmode.c:166(unix_mode) unix_mode(.) returning 0766 [2012/07/24 20:27:08.604532, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.604554, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.604583, 4] smbd/open.c:1990(open_file_ntcreate) calling open_file with flags=0x0 flags2=0x0 mode=0766, access_mask = 0x81, open_access_mask = 0x81 [2012/07/24 20:27:08.604679, 3] smbd/open.c:467(open_file) Error opening file . (NT_STATUS_ACCESS_DENIED) (local_flags=0) (flags=0) [2012/07/24 20:27:08.604705, 3] smbd/error.c:80(error_packet_set) error packet at smbd/error.c(160) cmd=162 (SMBntcreateX) NT_STATUS_ACCESS_DENIED [2012/07/24 20:27:08.606977, 3] smbd/process.c:1489(process_smb) Transaction 26 of length 80 (0 toread) [2012/07/24 20:27:08.607096, 3] smbd/process.c:1298(switch_message) switch message SMBtrans2 (pid 2440) conn 0x7f6758780c00 [2012/07/24 20:27:08.607119, 4] smbd/uid.c:257(change_to_user) change_to_user: Skipping user change - already user [2012/07/24 20:27:08.607139, 3] smbd/trans2.c:5100(call_trans2qfilepathinfo) call_trans2qfilepathinfo: TRANSACT2_QPATHINFO: level = 1004 [2012/07/24 20:27:08.607162, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.607184, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.607208, 3] smbd/trans2.c:5226(call_trans2qfilepathinfo) call_trans2qfilepathinfo . (fnum = -1) level=1004 call=5 total_data=0 [2012/07/24 20:27:08.608306, 3] smbd/process.c:1489(process_smb) Transaction 27 of length 80 (0 toread) [2012/07/24 20:27:08.608362, 3] smbd/process.c:1298(switch_message) switch message SMBtrans2 (pid 2440) conn 0x7f6758780c00 [2012/07/24 20:27:08.608383, 4] smbd/uid.c:257(change_to_user) change_to_user: Skipping user change - already user [2012/07/24 20:27:08.608403, 3] smbd/trans2.c:5100(call_trans2qfilepathinfo) call_trans2qfilepathinfo: TRANSACT2_QPATHINFO: level = 1005 [2012/07/24 20:27:08.608439, 3] smbd/vfs.c:881(check_reduced_name) check_reduced_name [.] [/data/localdevs/user1] [2012/07/24 20:27:08.608461, 3] smbd/vfs.c:1038(check_reduced_name) check_reduced_name: . reduced to /data/localdevs/user1 [2012/07/24 20:27:08.608484, 3] smbd/trans2.c:5226(call_trans2qfilepathinfo) call_trans2qfilepathinfo . (fnum = -1) level=1005 call=5 total_data=0

Read the article

OpenVPN Server Ethernet Bridging Question

- by Hooplad

Hello All, I am having a difficult time properly configuring an ethernet bridge using OpenVPN 2.0.9 install on CentOS 5 ( VPN server ). The goal that I am trying to complete is to connect a VM ( instance running on the same CentOS machine ) acting as a Microsoft Business Contact Manager server. I would then like this "BCM server" to serve Windows XP clients on 192.168.1.0/24 network as well as clients connecting from VPN ( 10.8.0.0/24 ). The setup as it is now was based off a known working configuration. The problem with the working configuration was that it would allow to the client to connect and access everything running on the VPN server ( SVN, Samba, VM Server ) but not any computers on the 192.168.1.0/24 network. I must disclose that the VPN server is behind a router/firewall. Ports are being forwarded correctly ( again, clients were able to connect to the VPN server with no problem. netcat confirms the udp port is open as well ). current ifconfig output br0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 inet addr:192.168.1.169 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:5eff:fe4d:3ac2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:846890 errors:0 dropped:0 overruns:0 frame:0 TX packets:3072351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42686842 (40.7 MiB) TX bytes:4540654180 (4.2 GiB) eth0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:882641 errors:0 dropped:0 overruns:0 frame:0 TX packets:1781383 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:82342803 (78.5 MiB) TX bytes:2614727660 (2.4 GiB) Interrupt:169 eth1 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:650 errors:0 dropped:0 overruns:0 frame:0 TX packets:1347223 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67403 (65.8 KiB) TX bytes:1959529142 (1.8 GiB) Interrupt:233 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:17452058 errors:0 dropped:0 overruns:0 frame:0 TX packets:17452058 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94020256229 (87.5 GiB) TX bytes:94020256229 (87.5 GiB) tap0 Link encap:Ethernet HWaddr DE:18:C6:D7:01:63 inet6 addr: fe80::dc18:c6ff:fed7:163/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3086 errors:0 dropped:166 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:315099 (307.7 KiB) vmnet1 Link encap:Ethernet HWaddr 00:50:56:C0:00:01 inet addr:192.168.177.1 Bcast:192.168.177.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet8 Link encap:Ethernet HWaddr 00:50:56:C0:00:08 inet addr:192.168.55.1 Bcast:192.168.55.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4226 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) current route table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.55.0 * 255.255.255.0 U 0 0 0 vmnet8 192.168.177.0 * 255.255.255.0 U 0 0 0 vmnet1 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 current iptables output Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination server_known_working.conf local banshee port 1194 proto udp dev tap0 ca ca.crt cert banshee_server.crt key banshee_server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 192.168.1.0 255.255.255.0" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 4 The following is the current CentOS server config file. server_ethernet_bridged.conf ( current ) local 192.168.1.169 port 1194 proto udp dev tap0 ca ca.crt cert server.crt key server.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.1.169 255.255.255.0 192.168.1.200 192.168.1.210 push "route 192.168.1.0 255.255.255.0 192.168.1.1" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 6 The following is one of the client's config file that was used with the known working configuration. client.opvn client dev tap proto udp remote XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca client.crt cert client.crt key client.key tls-auth client.key 1 verb 3 I have tried the HOWTO provided by OpenVPN as well as others http://www.thebakershome.net/openvpn%5Ftutorial?page=1 with no success. Any help or suggestions would be appreciated.

Read the article

Crossover LAN connection between Ubuntu And Windows 7 is not working

- by brett

my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

Read the article

Need help identiying a nasty rootkit in Windows

- by goofrider

I have a nasty rootkit that not tools seem to be able to idenity. I know for sure it's a rootkit, but I can figure out which rootkit it is. Here's what I gathered so far: It creates multiple copies of itself in %HOME%\Local Settings\Temp with names like Q.EXE, IAJARZ.exe, etc., and install them as hidden services. These EXE have SysInternals identifiers in them so they're definitely rootkits. It hooked very deep in the system, including file read/write, security policies, registry read/write, and possibly WinSock/TCP/IP. When going to Sophos.com to download their software, the rootkit inject something called Microsoft Ajax Tootkit into the page, which injects code into the email submission form in order to redirect it. (EDIT: I might have panicked. Looks like Sophos does use an AJAZ email form, their form is just broken on Chrome so it looked like a mail form injection attack, the link is http://www.sophos.com/en-us/products/free-tools/virus-removal-tool/download.aspx ) Super-Antispyware found a lot of spyware cookies, in the name of .kaspersky.2o7.net, etc. (just chedk 2o7.net, looks like it's a legit ad company) I tried comparing DNS lookup from the infected systems and from system in other physical locations, no DNS redirections it seems. I used dd to copy the MBR and compared it with the MBR provided by ms-sys package, no differences so it's not infecting MBR. No antivirus or rootkit scanner be able to identify it. Most of them can't even find it. I tried scanning, in-situ (normal mode), in safe mode, and boot to linux live CD. Scanners used: Avast, Sophos anti rootkit, Kasersky TDSSKiller, GMER, RootkitRevealer, and many others. Kaspersky reported some unsigned system files that ought to be signed (e.g. tcpip.sys), and reported a number of MD5 mismatches. But otherwise couldn't identify anything based on signature. When running Sysinternal RootkitRevealer and Sophos AntiRootkit, CPU usage goes up to 100% and gets stucked. The Rootkit is blocking them. When trying running/installing HiJackThis, RootkitRevealer and some other scanners, it tells me system security policy prevent running/installing it. The list of malicious acitivities go on and on. here's a sample of logs from all my scans. In particular, aswSnx.SYS, apnenfno.sys and PROCMON20.SYS has a huge number of hooks. It's hard to tell if the rootkit replaced legit program files like aswSnx.SYS (from Avast) and PROCMON20.SYS (from Sysinternal Process Monitor). I can't find whether apnenfno.sys is from a legit program. Help to identify it is appreciated. Trend Micro RootkitBuster ------ [HIDDEN_REGISTRY][Hidden Reg Value]: KeyPath : HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\sptd\Cfg Root : 586bfc0 SubKey : Cfg ValueName : g0 Data : 38 23 E8 D0 BF F2 2D 6F ... ValueType : 3 AccessType: 0 FullLength: 61 DataSize : 32 [HOOKED_SERVICE_API]: Service API : ZwCreateMutant Image Path : C:\WINDOWS\System32\Drivers\aswSnx.SYS OriginalHandler : 0x8061758e CurrentHandler : 0xaa66cce8 ServiceNumber : 0x2b ModuleName : aswSnx.SYS SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwCreateThread Image Path : c:\windows\system32\drivers\apnenfno.sys OriginalHandler : 0x805d1038 CurrentHandler : 0xaa5f118c ServiceNumber : 0x35 ModuleName : apnenfno.sys SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwDeleteKey Image Path : C:\WINDOWS\system32\Drivers\PROCMON20.SYS OriginalHandler : 0x80624472 CurrentHandler : 0xa709b0f8 ServiceNumber : 0x3f ModuleName : PROCMON20.SYS SDTType : 0x0 HiJackThis ------ O23 - Service: JWAHQAGZ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\JWAHQAGZ.exe O23 - Service: LHIJ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\LHIJ.exe Kaspersky TDSSKiller ------ 21:05:58.0375 3936 C:\WINDOWS\system32\ati2sgag.exe - copied to quarantine 21:05:59.0217 3936 ATI Smart ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0342 3936 C:\WINDOWS\system32\BUFADPT.SYS - copied to quarantine 21:05:59.0856 3936 BUFADPT ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0965 3936 C:\Program Files\CrashPlan\CrashPlanService.exe - copied to quarantine 21:06:00.0152 3936 CrashPlanService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0246 3936 C:\WINDOWS\system32\epmntdrv.sys - copied to quarantine 21:06:00.0433 3936 epmntdrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0464 3936 C:\WINDOWS\system32\EuGdiDrv.sys - copied to quarantine 21:06:00.0526 3936 EuGdiDrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0604 3936 C:\Program Files\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService.exe - copied to quarantine 21:06:01.0181 3936 FLEXnet Licensing Service ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0321 3936 C:\Program Files\AddinForUNCFAT\UNCFATDMS.exe - copied to quarantine 21:06:01.0430 3936 OTFSDMS ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0492 3936 C:\WINDOWS\system32\DRIVERS\tcpip.sys - copied to quarantine 21:06:01.0539 3936 Tcpip ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0601 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - copied to quarantine 21:06:01.0664 3936 HKLM\SYSTEM\ControlSet003\services\TULPUWOX - will be deleted on reboot 21:06:01.0664 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - will be deleted on reboot 21:06:01.0664 3936 TULPUWOX ( UnsignedFile.Multi.Generic ) - User select action: Delete 21:06:01.0757 3936 C:\WINDOWS\system32\Drivers\usbaapl.sys - copied to quarantine 21:06:01.0866 3936 USBAAPL ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0913 3936 C:\Program Files\VMware\VMware Player\vmware-authd.exe - copied to quarantine 21:06:02.0443 3936 VMAuthdService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - User select action: Skip 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - User select action: Skip

Read the article

Making nginx withstand flood attacks

- by Tiffany Walker

How can I make it stand stand against attacks better? Are their plugins. Looking for a way to RATE LIMIT and remain up and not slow down. My Setup: user nobody; # no need for more workers in the proxy mode worker_processes 4; worker_cpu_affinity 0001 0010 0100 1000; worker_priority -2; error_log /var/log/nginx/error.log info; worker_rlimit_nofile 40480; events { worker_connections 5120; # increase for busier servers use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks if_not_owner; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 5; gzip on; gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 9; gzip_buffers 16 8k; # You can remove image/png image/x-icon image/gif image/jpeg if you have slow CPU gzip_types text/plain text/xml text/css application/x-javascript application/xml image/png image/x-icon image/gif image/jpeg application/xml+rss text/javascript application/atom+xml; ignore_invalid_headers on; client_header_timeout 3m; client_body_timeout 3m; send_timeout 3m; reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 200M; client_body_buffer_size 128k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; include "/etc/nginx/vhosts/*"; } vhost file: server { error_log /var/log/nginx/vhost-error_log warn; listen 194.145.208.19:80; server_name ipxnow.in www.ipxnow.in; access_log /usr/local/apache/domlogs/ipxnow.in-bytes_log bytes_log; access_log /usr/local/apache/domlogs/ipxnow.in combined; root /home/ipxnowin/public_html; location / { location ~.*\.(3gp|gif|jpg|jpeg|png|ico|wmv|avi|asf|asx|mpg|mpeg|mp4|pls|mp3|mid|wav|swf|flv|html|htm|txt|js|css|exe|zip|tar|rar|gz|tgz|bz2|uha|7z|doc|docx|xls|xlsx|pdf|iso)$ { expires 7d; try_files $uri @backend; } error_page 405 = @backend; add_header X-Cache "HIT from Backend"; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location @backend { internal; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ .*\.(php|jsp|cgi|pl|py)?$ { proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ /\.ht { deny all; } } and proxy.inc: proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;

Read the article

Help me upgrade my pf.conf for OpenBSD 4.7

- by polemon

I'm planning on upgrading my OpenBSD to 4.7 (from 4.6) and as you may or may not know, they changed the syntax for pf.conf. This is the relevant portion from the upgrade guide: pf(4) NAT syntax change As described in more detail in this mailing list post, PF's separate nat/rdr/binat (translation) rules have been replaced with actions on regular match/filter rules. Simple rulesets may be converted like this: nat on $ext_if from 10/8 -> ($ext_if) rdr on $ext_if to ($ext_if) -> 1.2.3.4 becomes match out on $ext_if from 10/8 nat-to ($ext_if) match in on $ext_if to ($ext_if) rdr-to 1.2.3.4 and... binat on $ext_if from $web_serv_int to any -> $web_serv_ext becomes match on $ext_if from $web_serv_int to any binat-to $web_serv_ext nat-anchor and/or rdr-anchor lines, e.g. for relayd(8), ftp-proxy(8) and tftp-proxy(8), are no longer used and should be removed from pf.conf(5), leaving only the anchor lines. Translation rules relating to these and spamd(8) will need to be adjusted as appropriate. N.B.: Previously, translation rules had "stop at first match" behaviour, with binat being evaluated first, followed by nat/rdr depending on direction of the packet. Now the filter rules are subject to the usual "last match" behaviour, so care must be taken with rule ordering when converting. pf(4) route-to/reply-to syntax change The route-to, reply-to, dup-to and fastroute options in pf.conf move to filteropts; pass in on $ext_if route-to (em1 192.168.1.1) from 10.1.1.1 pass in on $ext_if reply-to (em1 192.168.1.1) to 10.1.1.1 becomes pass in on $ext_if from 10.1.1.1 route-to (em1 192.168.1.1) pass in on $ext_if to 10.1.1.1 reply-to (em1 192.168.1.1) Now, this is my current pf.conf: # $OpenBSD: pf.conf,v 1.38 2009/02/23 01:18:36 deraadt Exp $ # # See pf.conf(5) for syntax and examples; this sample ruleset uses # require-order to permit mixing of NAT/RDR and filter rules. # Remember to set net.inet.ip.forwarding=1 and/or net.inet6.ip6.forwarding=1 # in /etc/sysctl.conf if packets are to be forwarded between interfaces. ext_if="pppoe0" int_if="nfe0" int_net="192.168.0.0/24" polemon="192.168.0.10" poletopw="192.168.0.12" segatop="192.168.0.20" table <leechers> persist set loginterface $ext_if set skip on lo match on $ext_if all scrub (no-df max-mss 1440) altq on $ext_if priq bandwidth 950Kb queue {q_pri, q_hi, q_std, q_low} queue q_pri priority 15 queue q_hi priority 10 queue q_std priority 7 priq(default) queue q_low priority 0 nat-anchor "ftp-proxy/*" rdr-anchor "ftp-proxy/*" nat on $ext_if from !($ext_if) -> ($ext_if) rdr pass on $int_if proto tcp to port ftp -> 127.0.0.1 port 8021 rdr pass on $ext_if proto tcp to port 2080 -> $segatop port 80 rdr pass on $ext_if proto tcp to port 2022 -> $segatop port 22 rdr pass on $ext_if proto tcp to port 4000 -> $polemon port 4000 rdr pass on $ext_if proto tcp to port 6600 -> $polemon port 6600 anchor "ftp-proxy/*" block pass on $int_if queue(q_hi, q_pri) pass out on $ext_if queue(q_std, q_pri) pass out on $ext_if proto icmp queue q_pri pass out on $ext_if proto {tcp, udp} to any port ssh queue(q_hi, q_pri) pass out on $ext_if proto {tcp, udp} to any port http queue(q_std, q_pri) #pass out on $ext_if proto {tcp, udp} all queue(q_low, q_hi) pass out on $ext_if proto {tcp, udp} from <leechers> queue(q_low, q_std) pass in on $ext_if proto tcp to ($ext_if) port ident queue(q_hi, q_pri) pass in on $ext_if proto tcp to ($ext_if) port ssh queue(q_hi, q_pri) pass in on $ext_if proto tcp to ($ext_if) port http queue(q_hi, q_pri) pass in on $ext_if inet proto icmp all icmp-type echoreq queue q_pri If someone has experience with porting the 4.6 pf.conf to 4.7, please help me do the correct changes. OK, this is how far I've got: I commented out nat-anchor and rdr-anchor, as describted in the guide: #nat-anchor "ftp-proxy/*" #rdr-anchor "ftp-proxy/*" And this is how I've "converted" the rdr rules: #nat on $ext_if from !($ext_if) -> ($ext_if) match out on $ext_if from !($ext_if) nat-to ($ext_if) #rdr pass on $int_if proto tcp to port ftp -> 127.0.0.1 port 8021 match in on $int_if proto tcp to port ftp rdr-to 127.0.0.1 port 8021 #rdr pass on $ext_if proto tcp to port 2080 -> $segatop port 80 match in on $ext_if proto tcp tp port 2080 rdr-to $segatop port 80 #rdr pass on $ext_if proto tcp to port 2022 -> $segatop port 22 match in on $ext_if proto tcp tp port 2022 rdr-to $segatop port 22 rdr pass on $ext_if proto tcp to port 4000 -> $polemon port 4000 match in on $ext_if proto tcp tp port 4000 rdr-to $polemon port 4000 rdr pass on $ext_if proto tcp to port 6600 -> $polemon port 6600 match in on $ext_if proto tcp tp port 6600 rdr-to $polemon port 6600 Did I miss anything? Is the anchor for ftp-proxy OK as it is now? Do I need to change something in the other pass in on... lines?

Search Results

Search found 14837 results on 594 pages for 'duplicate ip'.

Page 583/594 | < Previous Page | 579 580 581 582 583 584 585 586 587 588 589 590 | Next Page >

- by Lekensteyn

- by Vladimir

- by Ronnie Jespersen

- by dpalau

- by steve_eyre

- by Luca G. Soave

- by Peter

- by derty

- by austinian

- by Charlotte

- by Alexey Perepechko

- by Fitzroy

- by Dmitro

- by Quan Tran

- by Conor McDermottroe

- by einpoklum

- by Ralph

- by Alan DeLonga

- by Patrick

- by user893730

- by Hooplad

- by brett

- by goofrider

- by Tiffany Walker

- by polemon

< Previous Page | 579 580 581 582 583 584 585 586 587 588 589 590 | Next Page >