Search Results

Search found 28789 results on 1152 pages for 'ubuntu netbook'.

Page 586/1152 | < Previous Page | 582 583 584 585 586 587 588 589 590 591 592 593  | Next Page >

  • Resize a pendrive Linux?

    - by user11239
    I'm running Ubuntu from USB media, which has a drive capacity of 250 GB, all existing as one FAT32 partition. However, when I created the bootable Ubuntu drive, only 4.79 GB were allocated for usage. Rather than put files directly into the /cdrom where the drive is mounted, I want to expand what is listed here in aufs to be at least 200 GB. I'm hopeful that I can do this live. Output of df : Filesystem 1K-blocks Used Available Use% Mounted on aufs 4051904 4050108 0 100% / none 1542852 284 1542568 1% /dev /dev/sdb1 244076800 4901648 239175152 3% /cdrom /dev/loop0 688000 688000 0 100% /rofs none 1547840 1496 1546344 1% /dev/shm tmpfs 1547840 4828 1543012 1% /tmp none 1547840 80 1547760 1% /var/run none 1547840 0 1547840 0% /var/lock none 1547840 0 1547840 0% /lib/init/rw Output of fdisk -l : Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00083fe4 Device Boot Start End Blocks Id System /dev/sdb1 * 1 30401 244196001 c W95 FAT32 (LBA) So basically what I want to do is get /dev/sdb1 to be entirely, or almost entirely read as aufs. I'm confused over how to do this, as the file systems are all part of /dev/sdb1 on one big partition, rather than separate partitions for separate file systems.

    Read the article

  • Can't use nvidia card/driver on optimus notebook

    - by Mr. Pixel
    I installed (once again) the latest official nvidia driver for my GT540m on Ubuntu 11.10. Even though everything seems OK with my xorg.conf file (I've manually added BusID "PCI:1:0:0", since lspci shows 01:00.0 for my GPU). The problem is, when I use the xorg.conf file generated by Xorg -configure, Xorg automatically loads the Intel GPU. So I removed everything that was not related to my nvidia card, basically leaving my xorg.conf with one screen and one device (with the nvidia driver and the above-mentioned BusID), and Xorg fails to start. The log says something like "Devices on GT540m [newline] none" And a few lines later, something like "NVIDIA(0) found a screen, but have no device for it". When I don't set the BusID, it doesn't seem to detect my card either. Thank you for any suggestion. PS: If possible, I'd like to avoid bumblebee or any similar "hybrid graphics" solution, last time I tried I ended up reinstalling Ubuntu. Edit: Allow me to clarify the problem. I have a notebook with a GT540m graphics card, and an integrated intel gpu. I want to use the graphics card with full hardware acceleration and its official driver, as I do under windows.

    Read the article

  • My card reader doesn't show up at all, but previously did in 10.10

    - by Nathan J. Brauer
    I bought a pin-based-USB powered internal media card reader and it worked perfectly when I first installed Ubuntu 10.10 a month ago. I used it a few times since and today I booted up the computer and it's not working. Here's how it used to work: In nautilus->computer, 5 "drives" would display even when no card was inserted. One for each slot (SD, XD, CF/MS, etc). Opening one w/o a card would initiate a "Please insert card." dialog. Inserting a card would automatically open nautilus. Now: No drives display at all whether cards are inserted or not. lsusb lists the following (which seems to indicate that it's not being detected) Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 046d:c52e Logitech, Inc. (my keyboard/mouse) Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub (A side note, all of my USB ports are 2.0 + 1 USB port which is 3.0, why does everything say 1.1/2.0?) I tried using ubuntu-bug but for USB devices it expects you to be able to remove and insert them while the computer is running -- obviously something you probably shouldn't be doing when you're dealing with devices plugged straight into the USB pins. Thanks in advance!

    Read the article

  • I'm stuck on User Defined Session destop environment

    - by Dan
    I just installed Ubuntu for the first time dual boot so I get to choose Ubuntu or windows. I then changed the setting where is doesn't ask for my password when booting up. I then installed Edubuntu desktop package. I then hit system and logged out that way i could be at the loggin screen that also lets you select the desktop environment. Edubuntu was not there but User defined session was so i clicked that thinking that might be Edubuntu and logged in. Now im totally stuck. Only walpaper on the screen as i realize now that is normal for user defined session but there is no log out button to change desktop environments now and since I set it to not ask for password at boot up there is no option to change it at start up. If i hit ctrl+alt+del it only lets you shutdown, restart, suspend, or hybernate.... no logg out. I have hit every key on the keybourd hoping something will pop up. I thought this must be a simple noob mistake that there must be endless artiles about this so did searches on google and forums and was shocked to find nothing about this. My next step unless someone can help is to uninstall and reinstall.

    Read the article

  • Problem installing drivers for Brother DCP-1400

    - by ToddB
    I have a problem installing drivers for my DCP-1400 printer. I am using Ubuntu 11.10 and am new to Ubuntu and Linux in general. I downloaded the lpr and cupswrapper files from the Brother linux site into my Download directory. I next run Terminal and switch to the Downloads directory. At the prompt I type in the following: sudo dpkg -i --force-all dcp1400lpr-1.1.2-1.386.deb It asks for my password which I type in and press Enter. I get the following errors: (Reading database ... 155195 files and directories currently installed.) Preparing to replace dcp1400lpr 1.1.2-1 (using dcp1400lpr-1.1.2-1.i386.deb) ... Unpacking replacement dcp1400lpr ... /var/lib/dpkg/info/dcp1400lpr.postrm: 3: /etc/init.d/lpd: not found dpkg: warning: subprocess old post-removal script returned error exit status 127 dpkg - trying script from the new package instead ... /var/lib/dpkg/tmp.ci/postrm: 3: /etc/init.d/lpd: not found dpkg: error processing dcp1400lpr-1.1.2-1.i386.deb (--install): subprocess new post-removal script returned error exit status 127 /var/lib/dpkg/tmp.ci/postrm: 3: /etc/init.d/lpd: not found dpkg: error while cleaning up: subprocess new post-removal script returned error exit status 127 Errors were encountered while processing: dcp1400lpr-1.1.2-1.i386.deb I now notice when I open the Synaptics package manager I get the message: E: The package dcp1400lpr needs to be reinstalled, but I can't find an archive for it. E: Internal error opening cache (1). Please report. Any help provided would be appreciated. Thank you TB

    Read the article

  • Can I set my Optimus Nvidia card to run Unity3D with bumblebee?

    - by manuhalo
    I'd like to know whether I can run compiz on my Nvidia card to speed things up. It's a Dell XPS15 laptop but I'm mostly using it as a desktop, so battery life is not important. Apparently my Intel integrated card is able to run unity 3D, but my Nvidia GT 420M is not. Here's the output of unity_support_test, both with optirun and without it: manuhalo@Ubuntu-XPS-L501X:~$ optirun /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce GT 420M/PCI/SSE2 OpenGL version string: 4.1.0 NVIDIA 280.13 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: no GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no manuhalo@Ubuntu-XPS-L501X:~$ /usr/lib/nux/unity_support_test -p OpenGL vendor string: Tungsten Graphics, Inc OpenGL renderer string: Mesa DRI Intel(R) Ironlake Mobile OpenGL version string: 2.1 Mesa 7.11 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes Any ideas of why this is happening? Thanks in advance to anyone able to shed some light on this. What I have tried: Installed the v290 drivers from the x-stable PPA. Tried forcing Unity-3D to work by telling Unity to ignore the unity-support-test results i.e. gksudo gedit /etc/environment add the following UNITY_FORCE_START=1 to the end of the file.

    Read the article

  • How to update Adobe's software unattendedly?

    - by jubel
    I would like to use unattended-upgrade to update the Adobe Reader, Flash Player and everything else of the Canonical partners. There fore, I added in /etc/apt/apt.conf.d/50unattended-upgrades Unattended-Upgrade::Allowed-Origins { "${distro_id} ${distro_codename}-security"; "${distro_id} ${distro_codename}-updates"; "Canonical ${distro_codename}"; // "${distro_id} ${distro_codename}-proposed"; // "${distro_id} ${distro_codename}-backports"; }; sudo unattended-upgrade --dry-run -d says Initial blacklisted packages: Starting unattended upgrades script Allowed origins are: ['o=Ubuntu,a=oneiric-security', 'o=Ubuntu,a=oneiric-updates', 'o=Canonical,a=oneiric'] Checking: acroread-common (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobe-flash-properties-gtk (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobe-flashplugin (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobereader-deu (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: handbrake-cli (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-stebbins-handbrake-snapshots' label:'HandBrake Snapshots' site:'ppa.launchpad.net' isTrusted:True>"]) Checking: handbrake-gtk (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-stebbins-handbrake-snapshots' label:'HandBrake Snapshots' site:'ppa.launchpad.net' isTrusted:True>"]) Checking: sopcast-player (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-ferramroberto-sopcast' label:'LffL Sopcast' site:'ppa.launchpad.net' isTrusted:True>"]) pkgs that look like they should be upgraded: Fetched 0 B in 0s (0 B/s) blacklist: [] InstCount=0 DelCount=0 BrokenCout=0 No packages found that can be upgraded unattended And it won't update. How can I update the third-party software automatically?

    Read the article

  • Hosting Bazaar shared repositories

    - by Kishor Kundan
    What i want ? We operate in a small team of 9 people including developers, QA and designers. I want to setup a version control. We have a ubuntu (server edition) and i want to host all our repositories there. I have no understanding that even if it is possible. What I have done? We have setup bazaar on all distributions. We are using Bazaar explorer as our gui front-end. The command edition from console isn't very comfortable to all members. We have gone through the manual, but it hasn't been very helpful. Our inexperience being the cause. Team The designers are using windows distribution and developers & QA are using ubuntu distributions. I have googled around and i am really struggling to find a good tutorial for this setup. So any links/guides/leads towards accomplishing the same would be very helpful. While posting links or answer please do consider our inexperience. Thank you !!! cheers

    Read the article

  • Installing nvidia drivers causes computer to boot to command prompt.

    - by levesque
    Hi, I have an Asus u30jc laptop, which comes with the Optimus prime graphics card switching technology that is now supported under 2.6.35, so I decided to give it a try. First I made sure the discrete graphics card was activated and then I installed the drivers proposed by the ubuntu software repository (nvidia-current). However, after rebooting all I got was a command prompt. My graphics card is a nvidia 310M. This is on Ubuntu 10.10 64 bits. What can I do to diagnose/identify the source of this problem? UPDATE: The messsages in my syslog tell me to check the xorg log: Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmDisplay: display lasted 0.053144 seconds Oct 11 12:42:59 u30jc-test gdm-simple-slave[1450]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmDisplay: display lasted 0.038176 seconds Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmLocalDisplayFactory: maximum number of X display failures reached: check X server log for errors Which I did. I found this message in my /var/log/Xorg.0.log : Fatal server error: [ 113.540] no screens found [ 113.540] What does that mean?

    Read the article

  • Keeping Xv Overlay configuration throughout an X session.

    - by kriss
    After upgrading my Linux system from Ubuntu 9.04 to Ubuntu 10.10, I suceeded correcting most problems (all related to Intel 82865G Integrated Graphics Adapter support and compiz is still not working but that's another matter) but for one I only have a partial solution. Whenever I play a video the colors are much too saturated. This is really a problem for tones of skins that appears reddish (everyone seems to be coming back from a ski vacation with deep sun burns). As this effect only occurs with videos, not with pictures, I finally figured out it was related to Video Overlays configuration and I can correct it typing: xvattr -a XV_SATURATION -v 120 This change the default saturation value, which is 500 and much too high in my case, at eye sight the correct value seems to be between 100 and 150. Now my problem is that I have to type the above command each time I run a video. If I type it before running the video it has no effect, if I close the video and open a new one, I have to type it again, etc. I tried to put it in Xsession and (logically) it has no effect either. How could I do to get the correct setting whenever I run a video without typing the above command every time ?

    Read the article

  • Dell Alps Touchpad not working

    - by ppls
    I have a Dell 17R SE with Ubuntu 13.04. The touchpad is recognized as PS/2 mouse out of the box, giving just normal touchpad behaviour, but no tap to click, no scrolling, etc. Most answers related to that issue suggest trying an ALPS driver from dahetral.com: http://www.dahetral.com/public-download For installing I followed the steps on this page: https://www.linuxwind.org/html/dell-touchpad-driver-for-ubuntu-13-04.html Now my xinput looks like this: Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2 Mouse id=13 [slave pointer (2)] ? ? AlpsPS/2 ALPS GlidePoint id=14 [slave pointer (2)] ? ? Logitech Bluetooth Mouse M555b id=16 [slave pointer (2)] My touchpad isn't working at all now, just the two hardware buttons for left and right mouse buttons work. Interestingly also the tap to click functions works, but only in the address bar of nautilus, nowhere (!) else. What can I do? I would even switch back to initial state, where at least the basic touchpad functionality worked, i I knew, how to get there.

    Read the article

  • I don't know how to connect to the internet

    - by Michiel
    I'm having some trouble finding an answer to my problem. I have a dell desktop (studio hybrid) and i have windows vista on it. The internet on windows vista works great, no problem. But now i downloaded Ubuntu 11.10 and I'm having problems. I can't find how to connect to my wireless network, when i click the network icon, it shows a list of things but I can only click 'enable wireless network' or something like that and 'edit connections'. But in this list it also says ( in a grey collor and i can't click it ) : 'No wireless connection, device not ready (firmware missing)" Or something like that. Now i tried several things i read on the internet (using my vista OS cause i can't use ubuntu for the internet, which is really enoying). But none of them helped me. I would like someone to tell me what my problem is or what information I have to give you to get an answer. So tell me if i have to edit a connection, or tell me how i have to get the wireless connection to work and to repair the 'firmware missing problem'. I hope someone can/is willing to help me. Bye

    Read the article

  • Cannot ping any computers on LAN

    - by Timothy
    I havem't been able to find a straight forward answer on this yet. I'm hoping people here are able to help! Keep in mind that I'm a complete beginner at this - this is the first installation i've done for any LINUX systems ever so please keep that in mind when answering this question. We are a complete Windows shop, using nothing but Microsoft products but looking into the value of OpenStalk however have been having problems getting Ubuntu Server installed and speaking to the network. The machine is getting an IP address which is telling me that some sort of DHCP activity is working but I'm not able to ping any computer on our network as well as not able to connect to the internet. Every time I try to ping i'm getting; Destination Host Unreachable I've tried using modifying the resolv.conf file with our static details to match my Windows 7 machine still with no luck. Even tried disabling the firewall on Ubuntu Server 11 and no luck. Any ideas? Please let me know if there is any information you need from the server and I'll post up.

    Read the article

  • How do I install the EW-7318Ug wireless drivers?

    - by user69731
    I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

    Read the article

  • Slow USB 3.0 speeds

    - by Cygnus X
    Long time forum forager, first time poster. I bought a Toshiba 500 GB usb 3.0 hard drive last week and instantly ran home to see how fast I could push it. On my desktop (that I built) I was able to get 200 MB/sec. On my laptop (MSI FX something or other), which I dual boot Windows 7/Ubuntu 11.10, I was able to get about 120 MB/sec on Windows, but on Ubuntu, i get about 25 MB/sec. lsusb shows: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 0bda:0139 Realtek Semiconductor Corp. Bus 002 Device 003: ID 1532:0015 Razer USA, Ltd Bus 004 Device 002: ID 0480:a007 Toshiba America Info. Systems, Inc. lspci -vvv shows that the USB 3.0 host controller is using the kernel driver in use is xhci_hcd. dmesg |grep usb shows: [ 1815.455368] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd [ 1815.475459] scsi7 : usb-storage 4-1:1.0 The built in disk utility says its connected via usb at 705 MB/s, but that's not what it reports when I transfer files over to it. Not really sure what to do at this point. Any help would be very nice, thank you.

    Read the article

  • Is this a dual monitor reset bug?

    - by Tentresh
    My two displays are: Intel GMA x4500 Laptop (1280x800 native resolution of the built-in display) External display (1920x1080) A few minutes after I login to my dual monitor setup, it gets reset to mirror screens. If I restore the settings via the displays application, everything is fine. On each reset, the following messages are written into /var/log/Xorg.0.log: [ 60.852] (II) PM Event received: Capability Changed [ 60.852] I830PMEvent: Capability change [ 132.920] (II) intel(0): EDID vendor "SEC", prod id 12869 [ 132.920] (II) intel(0): Printing DDC gathered Modelines: [ 132.920] (II) intel(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz) [ 134.228] (II) intel(0): Allocated new frame buffer 1280x800 stride 5120, tiled Whereas right on startup or manual resolution reset, /var/log/Xorg.0.log reports the expected frame buffer allocation: [ 1562.382] (II) intel(0): EDID vendor "SEC", prod id 12869 [ 1562.382] (II) intel(0): Printing DDC gathered Modelines: [ 1562.382] (II) intel(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz) [ 1576.740] (II) intel(0): Allocated new frame buffer 3200x1080 stride 12800, tiled Is Ubuntu 12.04 not compatible with my video card? Can this be solved within Ubuntu? I like its interface, but manually fiddling with resolution on every login is not bearable.

    Read the article

  • Laptop Charger Not Recognised Properly on Samsung NP900X3F

    - by user193732
    Firstly thanks for your time. Secondly, having an issue with my power charger on my Samsung Series 9 NP900X3F. When I boot into Ubuntu with the charger plugged in it recognises it as charging. When I unplug the charger after this it is still says it is charging. If I suspend in Ubuntu then plug/unplug during this suspended state it recognises it, but not during normal running. If I knew a little more I'm sure I could grab logs and find out what the difference between wake on suspend and normal running is, but alas I need help! I also am having issues with my keyboard backlight via the fn keys, but that I care about far less. Thank you very much. Linux mikey-900X3F 3.12.0-031200rc1-generic #201309161735 SMP Mon Sep 16 21:38:21 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux (I upgraded my kernel version to remove heinous horizontal artefacts I was getting) Happy to list more info about my system, ima bit of a noob. I did try searching however I can't find any questions at all about my system or related models with the same issue.

    Read the article

  • USB device is recognized but has no address

    - by SeanMG
    Good day folks, I'm trying to use a USRP1 with GNURadio if anyone knows what any of that is. I am running Ubuntu on a Windows 7 machine via VMware player. When I connect this USRP1 via USB 2.0 drive to Windows 7 it is recognized as Ettus Research LLC USRP1... When I connect the device to Ubuntu through VMware, it shows: usb device fffe:0002 on my removable devices. When I run lsusb I receive the following: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 0e0f:0003 VMware, Inc. Virtual Mouse Bus 002 Device 003: ID 0e0f:0002 VMware, Inc. Virtual USB Hub Bus 001 Device 004: ID fffe:0002 When I run this program that comes with the USRP driver... uhd_find_devices I receive: -------------------------------------------------- -- UHD Device 0 -------------------------------------------------- Device Address: type: usrp1 name: serial: 00000000 So when I run this program, it does recognize the fact that this device is connected. However, the device has no address, no name, and has a null serial. I need to know the device address so I can run more programs in GNURadio. Does anyone know what the problem is here? Thanks!

    Read the article

  • How do I copy a package from Debian to my PPA?

    - by Bernhard Reiter
    I'd like to add the latest gourmet package from Debian sid to our team's PPA so Ubuntu users who would like to run an up-to-date version of Gourmet can add that PPA to their software sources. (Dependency-wise, that shouldn't be much of an issue as pretty much all our current dependencies are already available in all currently supported Ubuntu versions.) I've downloaded the *.dsc file and debian and orig tarballs, and even figured out I could use this for the package's source.changes file. I also downloaded the Debian maintainer's public key so dput can validate the package. I then tried to upload the package to our PPA using dput ppa:~gourmet/ppa gourmet_0.17.3-1_source.changes (I also tried without the tilda.) This seemed to succeed, but I didn't get a confirmation email, and no packages are now displayed at our PPA, which leads me to believe that the package was rejected because the Debian maintainer's key is obviously not among our team members' keys. So what's the easiest way to "copy" a package from Debian (sid) to a Launchpad PPA? Do I really need to rebuild the entire package locally before I can upload it?

    Read the article

  • Setting up Cluster Configuration using an existing web server as a Primary Node?

    - by RapidWebs
    Thanks in advance for any help which is issued! I am having a slight issue, and need help with the decision making process when it comes to setting up my Cluster Configuration, consisting on a line of Ubuntu Servers (12.04). We currently have a Primary node, which resides in the US within a Datacenter, but we are going to be using this for all serious bandwidth and resource intensive websites, and through a configuration of Virtualmin + Webmin, will be setup as a sort of pseudo-cluster, using Virtualmins Cluster Modules. Anyways, on to the issue: We also have a business line setup locally, with three servers. here are their specs: Intel P4 2.4 ghz, 1GB Ram, 110 gb sata, Ubuntu 12.04* AMD 1.3 ghz, 512MB Ram, 20 GB IDE P3 Xeon 800mhz (dual physical processors), 1GB Ram, 3 * 25 GB Raid Configuration (one in use for host operating system). The first machine is currently IN USE and is serving virtual hosts off a sub-domain. My question is this: How can I integrate the Secondary node (which will be the Primary node per say, in this smaller configuration...) which is currently in use, into the cluster configuration w/ the other two servers for: Sharing Resources Redundancy (HA?) NFS /w the two Raid Disks without having the FORMAT the secondary node, and start fresh moving all my services in to a DRBD network drive or something similar, and than restoring all active virtualmin's Virtual hosts. the idea is that I want minimal downtime to people currently being served from server2.mywebsite.com, and from what I understand, all services need to be on a NFS so that they can be mounted on demand and accessed from the other machine taking over (i.e. Heartbeat + DRBD Config.) but my issue is that i already have all these services installed to their default directory structure: how can i most easily setup this NFS and HA system, move all my desires services to this new drive, and do it with minimal down time, and without breaking Virtualmin and everything else on my server? even just some pointers, a thread i could read, or a step by step check list or run down of commands i could issue to get started would be great! thanks!

    Read the article

  • 12.0.4.3 - Missing Battery Icon, auto Suspend not working, Keyboard shortcuts volume up/down no longer working

    - by Navraj
    Problems I am experiencing: Battery Icon not showing up unity bar (top right corner). Volume Up/Down/Mute not working. Bluetooth hot keys described above also not working.Brightness up/down keys on this keyboard no longer working (apple wireless keyboard) Laptop no longer suspends when lid is shut. I have to go to 'power' button on top right corner and click on 'Suspend' All was working flawlessly until I did the following: I have recently upgraded to Nvidia propriety driver version 319 {version recommended}. Installed Xscreensaver and then removed it and went back to default screensaver. Done a system update (1st since installing) and now currently running: Linux 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:19:35 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux NOTE: Base system was ubuntu 12.04.3 installed from ISO however lsb_release reports "No LSB modules are available" 4.installed psensor. I have check power setting (via Settings) and power setting via dconf-editor and set to recommended settings as described in posts detailing solution to this problem. - I have disabled 1) Nvdia settings at startup and 2) psensor at startup but this does not help. I am using an HP DV7 with 2GB Nvidia card. Not using any fancy graphics features. Recommendations? Thanks.

    Read the article

  • Fn key sticks down

    - by Oli
    Just bought my significant other a shiny new Samsung Q330 13" netbook, stuck an OCZ Agility in it and installed Maverick. Just as a quick aside, this is a devastating combination. Graphics work perfectly and it cold-boots to desktop in about 7 seconds. Very quick. But (common to laptops) I've got a couple of problems. I'll start with the most problematic and start a new thread for the other. Like a lot of laptops, there is a Fn (function) modifier to allow some keys to have another purpose. When I tried to alter the brightness of the screen by tapping Fn+Down, it worked but kept on going until it was as dim as it could go. I tapped Fn+Up and it went to the other extreme. After that the entire keyboard ceases to work properly because the Fn modifier appears to be locked. Additionally, and as a direct side effect, I think, clicking on things doesn't result in a standard result. It's as if control is being held. A reboot is the only thing that seems to fix these problems. This isn't a problem if you don't touch the Fn key but as there are two of them on the keyboard, an accident is going to happen sooner than later, requiring a reboot (and probably some data loss). I don't have a lot of experience with laptops (I prefer my hulking great desktop) so this isn't my area of expertise. I'm open to all suggestions, even disabling the two Fn keys until we can find a better solution.

    Read the article

  • nautilus crash when merging/overwriting files

    - by sBlatt
    On my Ubuntu 10.10, whenever I want to copy some files/folders over some other files/folders, or when I try to empty the trash, nautilus crashes! Example: I have a folder with some files. Now I want to overwrite this folder with a folder with the same name, same files, but some additional files, the merge window comes up, I choose merge and nautilus crashes (does not respond, when I press the close button I can force close it). Some times it even does the copying/emptying (trash), but it always crashes! This happens when copying to the same partition/ntfs partition/netshares, but not when I make a new folder and copy the files/folders into that (without overwriting anything). On a netshare, it's even possible to merge these files afterwards with another computer! dmesg/syslog/messages does not show any entry related to that problem. Does anyone have a solution for this very annoying problem? EDIT: dpkg -l nautilus* (see output in pastebin) EDIT2: I found out, nautilus already crashes before clicking replace/merge (as soon as the question appeares. In the video it's not entirely clear, that i click the cross before the force-close dialog appeares. Video of problem nautilus-debug-log.txt EDIT3: Filed bugreport: https://bugs.launchpad.net/ubuntu/+source/nautilus/+bug/678233

    Read the article

  • Ping Access to a Nested VM !! Plz Help

    - by Shivaramakrishnan
    I have a problem in communication between the host and the nested VM.This is my layout. I have installed KVM on host machine having a single nic interface (public ip) running Ubuntu.On top of this,I have VM running Ubuntu.I have installed KVM in this VM too.I then have a VM inside this running a web server. I am able to ping the host from this web server VM and ssh into it.But from host to VM ,ping is being unsuccessful. The VM (named L1hyp) on host was created using libvirt-manager and has IP of 192.168.122.8. The vswitch interface created at host is in default config (NAT-ed). Its IP is 192.168.122.1. Now this VM is also having a vswitch interface which is in default config (NAT-ed).Its IP is 192.168.100.1. The Web server VM is created on top of this L1hyp VM, is having an IP of 192.168.100.186. The Webserver VM uses 192.168.100.1 as its default gw. The L1hyp uses 192.168.122.1 as its default gw. From Host: ping 192.168.122.8 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS ping 192.168.100.1 - SUCCEEDS ping 192.168.100.186 - FAILS Comes up with Destination Host Unreachable From 192.168.122.1. But there is route to 192.168.100.0/24 subnet from host.Ping to 192.168.100.1 succeeds. From Webserver VM: ping 192.168.100.1 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS SSH from web server VM to host succeeds. Can anyone help me out what needs to be modified to have two way communication between the host and Webserver VM at the earliest? I am pondering over this problem for over a week now.

    Read the article

  • Unwanted Chinese language got set in system settings

    - by Registered User
    I was discussing on the Ubuntu users list how to type in in Hindi (Indic language) in Libre Office and about a package installation problem. I have made some changes in system settings, following suggestions by some users. However, this morning when I did a reboot I am unable to see English as my default language. My system is showing some Chinese characters which I do not understand. All I wanted was to use Libre Office for a particular document in Hindi. What happened is that even Gmail is opening in Chinese. The system settings folder and others are also opening in Chinese. I am unable to use the system now. I have uploaded the snapshots here: please have a look. Upon a reboot, I was asked to rename all folders. Gmail opening in Chinese This is how menu on my system looks: half English and half Chinese Notice that in the third snapshot the calendar and menu are appearing in Chinese. I want the original US English menus and folder names back. I just wanted to type a document with Lohit Hindi font in Libre Office. I use Ubuntu 11.10. I do not use Unity, only Gnome desktop. I installed gnome-session-fallback a long time back and have been using that ever since. How do I get back to all English submenus and English folder names? I have a US English Keyboard and I use only US English. This thing which is now somehow set is unwanted.

    Read the article

< Previous Page | 582 583 584 585 586 587 588 589 590 591 592 593  | Next Page >