Search Results

Search found 31973 results on 1279 pages for 'network library'.

Page 590/1279 | < Previous Page | 586 587 588 589 590 591 592 593 594 595 596 597  | Next Page >

  • VLAN setup on my PC

    - by Surjya Narayana Padhi
    Hi Geeks, I am bit new to VLAN. I want my two computers communicate through VLAN. I have following queries. As I am new to it my queries may be somewhat vague in some points. But i would like to hear from experts for my basic queries. I have two PCs Computer A and Computer B in two different IP networks Network A and Network B Both my PC has windows OS installed. How to send a VLAN(#Number) tagged packet from Computer A to Computer B and how to detect and untag the packet at Computer B? (Please provide the steps for windows OS) For this action do I need to check if my ethernet card supports VLAN tagging/untagging? If yes how can I know if my card supports it or not? Is the VLAN applied for Wireless ethernet controllers also? Do I need any switch or router for this action? Experts please given your inputs so that I can have a strong basic. If anyone can give some inputs how i can detect those VLAN in wireshirk, it will be helpful me also. Thanks in advance.

    Read the article

  • Windows Phone sync error when syncing with iTunes on different Hard Drive

    - by njallam
    I have my iTunes library file on a separate hard drive (which I believe may be the cause of the problem) and I have been trying to use it to synchronize with my Windows Phone. I would like to first note that if I set up my phone to synchronize with 'Windows Libraries', then it works fine. This is however not ideal as I have categorised my music and made playlists etc, on iTunes. When I first link my Windows Phone to the Windows Phone App (for desktop) and select iTunes from the above selection, I get the following error message: After searching that error, I found the following forum threads: Fix for error 8300300B when trying to sync Lumia 920 Windows 8 Phone in PC? Error code 8300300B on Windows Phone 8 while trying to sync I've tried the workarounds described in the above threads, however, they did not work for me. If I ignore that error message, I see the expected interface, along with all of my iTunes library's media, however the 'Sync' button is greyed out. I have tried some other things to try and fix this: Removing the app's AppData folder Uninstalling, reinstalling Using the full-screen modern app (does not allow for iTunes syncing)

    Read the article

  • Unable to connect to FTP - Connection timeout after MLSD

    - by Afrosimon
    So here is my problem, I'm absolutely unable to connect to a FTP server, in circumstances I've never seen before. Here is the situation : I get a "Connection timed out" just after the MLSD command. I usually use Filezilla, under Ubuntu, but to make sure the problem isn't related to this particular client I tried a few others : gftp on ubuntu and winscp and freeftp on windows 7. All the same result. Also made sure to try with Active or Passive modes. Same result. At this point I would be inclined to think there is something wrong with my current network (furthermore, according to a coworker the FTP server is OK). But I did check with http://ftptest.net/ and I am able to get the directory listing (which I'm not able to through a FTP client). So in the end the last thing I didn't tried is to go on another network, solution which seems would work, but wouldn't be very practical in the long run. And thus I guess there's something wrong with my router... but what could it possibly be? Note : I did try to register and post this question on filezilla's board first... but I can't create an account with a gmail nor hotmail account. WTF?

    Read the article

  • Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

    - by axk
    I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

    Read the article

  • Win Svr 2003 DHCP Bad Addresses

    - by VinceM
    After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

    Read the article

  • Application runs fine manually but fails as a scheduled task

    - by user42540
    I wasn't sure if this should go here or on stackoverflow. I have an application that loads some files from a network share (the input folder), extracts certain data from them and saves new files (zips them with SharpZLib) on a different network share (output folder). This application runs fine when you open it directly, but when it is set to a scheduled task, it fails in numerous places. This application is scheduled on a Win 2003 server. Let me say right off the bat, the scheduled task is set to use the same login account that I am currently logged in with, so it's not because it's using the LocalSystem account. Something else is going on here. Originally, the application was assigning a drive letter to the input folder using WNetGetConnectionA(). I don't remember why this was done, someone else on our team did that and she's gone now. I think there was some issue with using the WinZip command line with a UNC path. I switched from the WinZip command line utility to using SharpZLib because there were other issues with using the WinZip command line. Anyway, the application failed when trying to assign a drive letter with the error "connection already established." That wasn't true and even after trying WNetCancelConnection(), it still didn't work. Then I decided to just map the drive manually on the server. Then when the app calls Directory.Exists(inputFolderPath) it returns false, even though it does exist. So, for whatever reason, I cannot read this directory from within the application. I can manually navigate to this folder in Windows Explorer and open files. The app log file shows that the user executing it on the schedule is the user I expect, not LocalSystem. Any ideas?

    Read the article

  • CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

    - by SJaguar13
    I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

    Read the article

  • VLAN Tagging Traffic on Cisco Switch

    - by David W
    I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

    Read the article

  • How does Tunlr work?

    - by gravyface
    For those of you not in the US, Tunlr uses DNS witchcraft to allow you to access US-only (and UK-only stuff like BBC radio online) services and Websites like Hulu.com, etc. without using traditional methods like a VPN or Web proxy. From their FAQ: Tunlr does not provide a virtual private network (VPN). Tunlr is a DNS (domain name system) unblocking service. We’re using sophisticated technologies (a.k.a. the Tunlr Secret Sauce ©) to re-adress certain data envelopes, tricking the receiver into thinking the envelope originated from within the U.S. For these data envelopes, Tunlr is transparently creating a network tunnel from your location to our U.S.-based servers. Any data that’s not directly related to the video or music content providers which Tunlr supports is not only left untouched, it’s also not even routed through Tunlr. In order to use Tunlr, you will have to change the DNS address. See Get started for more information. I can't really wrap my head around how this works; I have always assumed that these services performed a geolocation lookup via your client IP. Just really curious as to how this works. EDIT 2 I believe they're only proxying the initial geo check and then modifying the data stream request to include your real IP address so that the streaming is direct, not proxied.

    Read the article

  • Self-connecting printers

    - by Martin Cerny
    Hello, I work as an administrator in a small company using XP Professional on all computers and two servers with Win 2003 Server. Recently a very unusual problam occured one of the computers keeps connecting to all the printers on the network it doesn't matter if it's an administrator or Domain User as soon as somebody logs in the commputer connects all the printers. The printers are either installed on local computers or on the server and shared. There is no log-on script connecting the printers, I install them manualy and none of the other computers shows such behaviour. We have a printer which is installed on two computers and both of them share it (I'm moving it to Server from a small PC which shared it up to now, but some computers still use the old connection), meaning this specific computer connects to one of the printer two times and it can't use either of the connections. How to prevent this self-connecting to all printers (none of the other computers has this problem). If I delte them from the "Printers" folder everything works fine untill I reconnect and the Folder is once again full of all the printers we have. I solved the smaller problem, computer is now capable of printing on all of the printers (it seems there have been some registry issues), after cleaning the registry and reinstalling the printer it seems to work just fine. But the second thing prevails, the computer connects to all the printers in the network (when I remove one/multiple it is reconnected right after the next log-in by any user).

    Read the article

  • Very slow connection to xserve via afp or smb

    - by Mhoffman13
    Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

    Read the article

  • After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

    - by gmonk
    I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

    Read the article

  • How to pin "Visual Studio 2010 Documentation" shortcut to Windows 7 taskbar?

    - by Chris W. Rea
    I just installed Microsoft Visual Studio 2010 at home, on my Windows 7 PC. One of the items installed with VS2010 is "Microsoft Visual Studio 2010 Documentation". I like to have the documentation installed locally and at my fingertips, and so before had always added a shortcut for the help viewer to my Quick Launch toolbar. However, I'm not able to pin the new documentation to the Windows 7 taskbar. It's frustrating. Note carefully: When I launch "Microsoft Visual Studio 2010 Documentation" from the Start menu, it seems to perform two functions: First, it launches the "Help Library Agent", which is a local HTTP server from which the help content is served... similar to the local ASP.NET web development server. Second, it launches the default web browser against the localhost URL corresponding to the port on which the "Help Library Agent" is running, for example: http://127.0.0.1:47873/help/1-1444/ms.help?method=f1&query=msdnstart&product=VS&productVersion=100&locale=en-US ... in other words, the program doesn't leave behind an active foreground process that displays in the taskbar. So, I can't choose "Pin this program to taskbar" as one might do so with a typical program. How can I get a shortcut to "Microsoft Visual Studio 2010 Documentation" in the Windows 7 taskbar? Has anybody got a workaround for this?

    Read the article

  • Netflix streaming stops loading at 98% on Revo 3700

    - by Martin Harris
    I'm trying to stream Netflix on an Acer Revo 3700 running Windows 7 Home Premium, but it hangs on the loading screen at 98% (after it has formatted the player to the right aspect ratio and added the controls, but before the video starts) with no error messages or failures. I have two other machines on the same network, one running Windows 7 Home Premium and another running XP, which both stream faultlessly. Things I have tried: Both a wired and wireless connection to the router Upgrading the video and audio drivers IE, Chrome and Firefox Boxee software Connecting with a VGA cable instead of HDMI (in case it is a HDCP thing) Uninstalling and reinstalling Silverlight. Getting someway into loading a HD movie and turning "Allow HD" off Does anyone know what Netflix is doing at the 98% load mark? Are there any log files? Anything else worth trying? Full disclosure: I'm using Netflix from the UK through a US based VPN. I've tried multiple VPNs and the problem is exactly the same, also the other machines on the same network through the same VPN work fine so I don't think this is the issue, but it might be a factor. The region check happens at around 7% and I get past that.

    Read the article

  • How can I keep SSH's know_hosts up to date (semi-securely)?

    - by Chas. Owens
    Just to get this out in front so I am not told not to do this: The machines in question are all on a local network with little to no internet access (they aren't even well connected to the corporate network) Everyone who has the ability to setup a man-in-the-middle attack already has root on the machine The machines are reinstalled as part of QA procedures, so having new host keys is important (we need to see how the other machines react); I am only trying to make my machine nicer to use. I do a lot of reinstalls on machines which changes their host keys. This necessitates going into ~/.ssh/known_hosts on my machine and blowing away to old key and adding the new key. This is a massive pain in the tuckus, so I have started considering ways to automate this. I don't want to just blindly accept any host key, so patching OpenSSH to ignore host keys is out. I have considered creating a wrapper around the ssh command the will detect the error coming back from ssh and present me with a prompt to delete the old key or quit. I have also considered creating a daemon that would fetch the latest host key from a machine on a whitelist (there are about twenty machines that are being constantly reinstalled) and replace the old host key in known_hosts. How would you automate this process?

    Read the article

  • How is route automatic metric calculated on Windows 7?

    - by e-t172
    KB299540 explains how Windows XP automatically assign metrics to IP routes: The following table outlines the criteria that is used to assign metrics for routes that are bound to network interfaces of various speeds. Greater than 200 Mb: 10 Greater than 20 Mb, and less than or equal to 200 Mb: 20 Greater than 4 Mb, and less than or equal to 20 Mb: 30 Greater than 500 kilobits (Kb), and less than or equal to 4 Mb: 40 Less than or equal to 500 Kb: 50 However, they seem to have changed their algorithm in Windows 7, as my routing table looks like this: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.3 10 0.0.0.0 0.0.0.0 10.202.254.254 10.202.1.2 286 10.202.0.0 255.255.0.0 On-link 10.202.1.2 286 10.202.1.2 255.255.255.255 On-link 10.202.1.2 286 10.202.255.255 255.255.255.255 On-link 10.202.1.2 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 On-link 192.168.0.3 266 192.168.0.3 255.255.255.255 On-link 192.168.0.3 266 192.168.0.255 255.255.255.255 On-link 192.168.0.3 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.0.3 266 224.0.0.0 240.0.0.0 On-link 10.202.1.2 286 255.255.255.255 255.255.255.255 On-link 10.202.1.2 40 =========================================================================== The only "correct" metric is the first one (Gigabit connection = 10). However, other routes using the Gigabit connection have metric = 266, my VPN has metric = 286, and loopback is 306 (?!). Any idea what's going on?

    Read the article

  • Ubuntu 10.04->10.10 in failed state - how to recover?

    - by Harvey
    I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: (1) "Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a)." (2) "gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok]" (3) "gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ..." What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

    Read the article

  • Collect temperature and fan speed with munin from Windows 7 PC?

    - by nfm
    Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

    Read the article

  • Which Revision Control Software to use for Personal Dropbox?

    - by wag2639
    I want to set up a sync repositiory that would be similar to Dropbox. Goals/Requirements: Free (Open Source very preferable) Linux host (probably Ubuntu) Windows/Mac/Linux clients Potential for multiple users with limited access (optional) Preferable easy, doesn't necessarily need to be automatic Revision control very preferable Basically, I want to be able to use multiple computers, possible with different OS's, and be able to access, use, and sync files across all of them. I also want to have a local copy of the repository for when I'm not connected to the network (as if I'm working on a laptop, I want to keep a local repository to keep revision and merge later with "master" repository). For example, I'm editing a few pictures on my laptop during the day outside of my network, but when I get home, I would like to sync the changes, including incremental changes, with my desktop at home. I would also like my roommates to be able to access and use this repository too but limit access to certain files. For example, I may want to use this to backup financial records but wouldn't want them to have access to those files. I'm a programmer and familiar with SVN but I know that wouldn't be the most appropriate since it doesn't handle binaries well and doesn't keep a local repository. I know better choices exist but I don't really know them well enough to choose the best one.

    Read the article

  • Default IPv6 route on debian squeeze does not come up after boot

    - by Georg Bretschneider
    I have a problem with my default IPv6 route not coming up after boot on a Debian Squeeze system. This is my config (/etc/network/interfaces): # Loopback device: auto lo iface lo inet loopback iface lo inet6 loopback # device: br0 auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 88.198.62.xx broadcast 88.198.62.63 netmask 255.255.255.224 gateway 88.198.62.33 up route add -net 88.198.62.32 netmask 255.255.255.224 gw 88.198.62.33 br0 iface br0 inet6 static address 2a01:4f8:131:10x::2 netmask 64 gateway 2a01:4f8:131:100::1 up route -A inet6 add 2a01:4f8:131:100::1/59 dev br0 My inet comes up alright, but I have to exec the route command manually after boot to make IPv6 work. Otherwise I can't even reach my gateway. This is the output of ip -6 route show after boot: 2a01:4f8:131:10x::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 unreachable fe80::/64 dev lo proto kernel metric 256 error -101 mtu 16436 advmss 16376 hoplimit 4294967295 fe80::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 I already tried it with: up ip -6 route add 2a01:4f8:131:100::1 dev br0 up ip -6 route add default via 2a01:4f8:131:100::1 dev br0 in /etc/network/interfaces, but with the same results. If I execute those commands manually on my shell, everything starts working nicely. And yes, I tried with post-up instead of up, too. Only other changes I made was to activate ip forwarding for IPv6, because I want to run some LXC containers on that system.

    Read the article

  • Regarding AD Domain controllers and remote branch offices

    - by Alex
    We have central HQ building and a lot of small branch offices connecting via VPN and want to implement AD (If you can believe we still haven't). We want everyone to log in using domain accounts and be policed centrally. We are OK with having a RODC in a branch office with like 10 computers. But we have these small branches with two to four PCs only. Some of these branches connect to HQ via IPSec site-to-site VPN, some via remote access (client-based) VPN. So there is no problem with ones that have local RODC or connecting to HQ DCs via VPN router. But how about small branches? We don't really want to set up a machine there, neither we want to invest into Windows Server licenses or fancy network equipment. Also, the problem is that we cannot access HQ DCs via VPN because we are not logged in and connected to HQ internal network yet, so DCs aren't reachable. What is typically done in that situation if it is needed to have central management over policies on those PCs? Or is it better to let 'em loose and use local policies and accounts in this situation?

    Read the article

  • libvirt's dnsmasq does not respond to dns queries or provide dhcp

    - by Jeremy
    This is on Ubuntu 10.04 server, using KVM to run Ubuntu guests. This system has been working for a long time and I have not changed anything (other than applying security updates), but today I found dnsmasq no longer responds to requests. I cannot say how long this has been broken for me because I don't frequently use the NAT'd guests. So it could have started just after the last updates or some other event and I just now found it. I can connect to port 53 with telnet at 192.168.122.1. I've flushed ip-tables to be sure it wasn't firewall rules and that is not the problem. dnsmasq is running, virsh reports default network as stared. I can't find ANY information on troubleshooting libvirt dnsmasq except that it won't play well with other instances of dnsmasq, which is not the problem. I cannot even find where log entries might be for this service. Any ideas on where to look for more information? edit to add: I added another network and that one works fine. I guess I have a workaround but would still like to figure out how to troubleshoot this problem.

    Read the article

  • Improve wireless performance

    - by djechelon
    Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

    Read the article

  • Looking for a small, portable, port-mirroring ethernet switch.

    - by user37244
    I recently had a mac go haywire, taking half a minute or more to get www.google.com loaded. Getting its owner to give up the machine for repair was like pulling teeth - they were insisting that it must be something to do with the network, since so much had changed with the local configuration at about the same time their box went haywire. I eventually set up a port mirror to a box that I could remote to so I could show that the mac was only irregularly getting packets onto the network. Demonstrating this faced an additional challenge: the latency of the remote desktop software I was using meant that I had to point to timestamps instead of just the moment the packet flashed up on the screen as my evidence. This particular user was the reason this was so challenging this time around, but I would like to have a box that I can cart from desk to desk to use wireshark on my laptop at any station where I need it. 3com, cisco, netgear, etc. (ad nauseum), all make switches that can be configured for port mirroring, but in my case, the smaller, the better. For the sake of my sanity, I'll probably end up running it off a battery anyway. If my laptop had two ethernet ports, this would be easy. So, whaddya recommand for a device that requires 0 configuration at each powerup (though I'm fine with poking at it for a while to set it up initially.) Small, light, and cheap enough to get it past purchasing? Thanks,

    Read the article

  • Shortcut to "printer and faxes" on another computer

    - by Doltknuckle
    I have a print server running windows server 2008 that has about 50 printers on it. In windows XP, I was able to connect to the server using the UNC name and make a shortcut to the "printers and faxes" folder. (For the record, I know that it really isn't a folder, but that's outside the scope of this question.) I have recently switched to windows 7 and I find that the jump lists are really useful. One of the things I want to do is make it easy to connect to that server's "printers and faxes" folder. I would like to use something like a shortcut that I can open and go immediately to that location. The problem is that windows 7 doesn't have a way to create a shortcut like you could in WinXP. They have a button on the toolbar that says "view remote printers" which sends you to the correct folder. I'd like to avoid having to type out the server name. I also can't use the "view network" link in windows explorer. Our organization has over 6,000 machines and viewing the network lists all of them. This is all about saving time by using the minimum number of mouse clicks and key presses in normal operation. Does anyone have any suggestions?

    Read the article

< Previous Page | 586 587 588 589 590 591 592 593 594 595 596 597  | Next Page >