Search Results

Search found 31973 results on 1279 pages for 'network library'.

Page 591/1279 | < Previous Page | 587 588 589 590 591 592 593 594 595 596 597 598  | Next Page >

  • Windows Server 2008 ignores any change made to firewall

    - by Maurice Courtois
    I have been trying for the last 2 hours to make my Windows Server 2008 answer ping. I have tried almost every single solution I have found on the web, so far nothing work. My current setup: 2 NIC (1x Internet connection, 1x Local network) Server act as VPN server. So I set the corresponding NIC as either Public or Private. I also enable the rule for "File and Printer Sharing (Echo Request...)" for all Nic and from any IPs. I always been able to ping from the local network or the local ip while connected to the VPN. I also tried to create a specific rule for ICMP ping and disabling the firewall for all but the public nic. Regardless of all this, I still can't ping that server from Internet. Any idea suggestion what could cause this? I have the impression that when you set the server as VPN (I switch the box on when setting it up to block everything else than VPN connection) that changing anything to the firewall setting thought mmc is pointless !?!?

    Read the article

  • Switch to IPv6 and get rid of NAT? Are you kidding?

    - by Ernie
    So our ISP has set up IPv6 recently, and I've been studying what the transition should entail before jumping into the fray. I've noticed three very important issues: Our office NAT router (an old Linksys BEFSR41) does not support IPv6. Nor does any newer router, AFAICT. The book I'm reading about IPv6 tells me that it makes NAT "unnecessary" anyway. If we're supposed to just get rid of this router and plug everything directly to the Internet, I start to panic. There's no way in hell I'll put our billing database (With lots of credit card information!) on the internet for everyone to see. Even if I were to propose setting up Windows' firewall on it to allow only 6 addresses to have any access to it at all, I still break out in a cold sweat. I don't trust Windows, Windows' firewall, or the network at large enough to even be remotely comfortable with that. There's a few old hardware devices (ie, printers) that have absolutely no IPv6 capability at all. And likely a laundry list of security issues that date back to around 1998. And likely no way to actually patch them in any way. And no funding for new printers. I hear that IPv6 and IPSEC are supposed to make all this secure somehow, but without physically separated networks that make these devices invisible to the Internet, I really can't see how. I can likewise really see how any defences I create will be overrun in short order. I've been running servers on the Internet for years now and I'm quite familiar with the sort of things necessary to secure those, but putting something Private on the network like our billing database has always been completely out of the question. What should I be replacing NAT with, if we don't have physically separate networks?

    Read the article

  • Hadoop initscript askes password

    - by Ramesh
    I have installed hadoop on my ubuntu 12.04 single node .I am trying to execute an init script to make the hadoop run on start up but it asks password every time i execute. #!/bin/sh ### BEGIN INIT INFO # Provides: hadoop services # Required-Start: $network # Required-Stop: $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Description: Hadoop services # Short-Description: Enable Hadoop services including hdfs ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HADOOP_BIN=/home/naveen/softwares/hadoop-1.0.3/bin NAME=hadoop DESC=hadoop USER=naveen ROTATE_SUFFIX= test -x $HADOOP_BIN || exit 0 RETVAL=0 set -e cd / start_hadoop () { set +e su $USER -s /bin/sh -c $HADOOP_BIN/start-all.sh > /var/log/hadoop/startup_log case "$?" in 0) echo SUCCESS RETVAL=0 ;; 1) echo TIMEOUT - check /var/log/hadoop/startup_log RETVAL=1 ;; *) echo FAILED - check /var/log/hadoop/startup_log RETVAL=1 ;; esac set -e } stop_hadoop () { set +e if [ $RETVAL = 0 ] ; then su $USER -s /bin/sh -c $HADOOP_BIN/stop-all.sh > /var/log/hadoop/shutdown_log RETVAL=$? if [ $RETVAL != 0 ] ; then echo FAILED - check /var/log/hadoop/shutdown_log fi else echo No nodes running RETVAL=0 fi set -e } restart_hadoop() { stop_hadoop start_hadoop } case "$1" in start) echo -n "Starting $DESC: " start_hadoop echo "$NAME." ;; stop) echo -n "Stopping $DESC: " stop_hadoop echo "$NAME." ;; force-reload|restart) echo -n "Restarting $DESC: " restart_hadoop echo "$NAME." ;; *) echo "Usage: $0 {start|stop|restart|force-reload}" >&2 RETVAL=1 ;; esac exit $RETVAL Please tell me how to run hadoop without entering password.

    Read the article

  • IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

    - by Daniel
    I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

    Read the article

  • Access server using IP on another interface

    - by Markos
    I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

    Read the article

  • How to correctly deploy Adobe Reader 9.1

    - by Ben Gillam
    Hi I have recently tried to deploy Adobe Reader 9.1 onto our network here. (SBS 2003 server and XP Workstations) I followed the instructions for the extraction of the installer and .msi and then creating a .mst transform file to set custom options. (Suppress EULA, dont create desktop icon etc) I then added the package to my deployment GPO applied the relevant .mst file and preceded to deploy accross the network. The software package is computer assigned to be installed prior to logon, to avoid user permissions issues. The package deploys correctly to computers and will run perfectly fine if you run from a shortcut, however when trying to view a pdf from within a web browser it fails with the following message. "The adobe acrobat/reader that is running can not be used to view PDF files in a web browser. Adobe Acrobat/Reader version 8 or 9 is required. Please exit and try again" I have found many pages on google refering to this problem, but none appear to be in relation the problems I have found. http :// kb2.adobe.com/cps/405/kb405461.html These fixes recommend correcting a registry entry (which i should mention is missing after the deployed installation. However this does not work. Switching off display in a browser - Seems to defeat the object of fixing the problem Removing old versions - There arent any. Trying with a different user - This affects all users of all privalige levels on all computers. On my workstation I uninstalled Acrobat Reader 9.1 then reinstalled manually using the same installation source files and it works fine. has anyone sucsessfully deployed AR9.1 on their domain and if so how? For the time being I have downloaded the older 8.1.3 release and deployed this in the same way which works fine, but would like to be using the up to date version. Thanks

    Read the article

  • Unable to connect to server after a certain amount of time

    - by Troy
    I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

    Read the article

  • Cannot Connect To VMWare Guest OS Using Either RDP or VNC

    - by Humanier
    I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve the mentioned problems.

    Read the article

  • How to sandbox a VMWare image as much as possible

    - by Craig H
    The situation: -A corporate environment, with a corporate managed XP desktop (locked down, patched regularly, restricted user rights, no manual install of SW, AV, etc.) The requirement: -Using VMWare Workstation, run a sandboxed image (also XP) for specific testing purposes (with admin rights in the guest VM). No network connectivity is required. It can't be a separate standalone physical workstation disconnected from the network. (FWIW, this is a legitimate, sanctioned requirement - not someone trying to get around corporate restrictions.) The challenge: -Do this in as safe/secure a manner as possible. The proposed solution: -Create an image with host-only networking. -Perhaps remove the virtual ethernet adapter? (not sure if it's required for basic VMWare functionality?) The question (finally): -What potential risks remain (and how could I best mitigate them)? One challenge is that the guest VM will not be a managed workstation itself, so patching, AV, etc. can't be guaranteed (and, ironically, would in fact be somewhat difficult given the proposed solution!)

    Read the article

  • Connect two networks

    - by Meek Barrios
    Connecting two different offices with a wireless link and linux boxes. Hardware: 2 CISCO RV42, 2 Dual Homed Linux Boxes running debian, 2 2Wire and 2 AirMax 5 Configuration is: Office A LAN A (10.1.1.0/24) -> RV42 A (WAN1 - 10.1.1.254) -> 2Wire A (Internet) LINUX A ( ETH0 (LAN) 10.1.1.253, ETH1 (LINK) (10.1.3.3) Wireless Link --- AirMax A <-> AirMax B connected as Wireless Bridge Office B LAN B (10.1.2.0/24) -> RV42 B (WAN1 - 10.1.2.254) -> 2Wire B (Internet) LINUX B ( ETH0 (LAN) 10.1.2.253 -> ETH1 (LINK) (10.1.3.4) Network configuration is: LAN A - Default Gateway 10.1.1.254 RV42 A - Static Route 10.1.3.0/24 on 10.1.1.253 Static Route 10.1.2.0/24 on 10.1.1.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux A - ETH0 10.1.1.253 netmask 255.255.255.0 gw 10.1.1.254 ETH1 10.1.3.3 netmask 255.255.255.0 gw 10.1.3.1 AIRMAX A - 10.1.3.1 netmask 255.255.255.0 gw 10.1.3.1 LAN B - Default Gateway 10.1.2.254 RV42 B - Static Route 10.1.3.0/24 on 10.1.2.253 Static Route 10.1.1.0/24 on 10.1.2.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux B - ETH0 10.1.2.253 netmask 255.255.255.0 gw 10.1.2.254 ETH1 10.1.3.4 netmask 255.255.255.0 gw 10.1.3.2 AIRMAX B - 10.1.3.2 netmask 255.255.255.0 gw 10.1.3.2 Both linux have ip_forward set to 1 and the following on the iptables: iptables -F iptables -X iptables -P FORWARD ACCEPT iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT I can ping from Linux B any ip on 10.1.1.0/24 segment and on linux A any ip on 10.1.2.0/24 segment however I cannot connect to HTTP or FTP on those machines. From LAN A I cannot see any other network. I'm looking for some advice for this configuration or a better solution. Regards

    Read the article

  • How to create a static IP on Windows Server 2008 R2 so I can access the server remotely

    - by Aesir
    I have just purchased a HP Proliant N40L which I am intending to use as a NAS, learning tool and just in general something to mess around with. As a student via the Microsoft dreamspark program I can get a free copy of Windows Server 2008 R2 which I am using as the OS. So that I can remote to the box from outside of my local network and so that I can stream media from it to my PS3, I have read that I need to create a static IP for the server and use port forwarding to forward to this IP so I can remote in. Is this correct? I am not really sure how to do this and if I need to make these changes on my router configuration, on the OS or both. I am a novice when it comes to networking however most resources for Windows server 2008 R2 seem to assume a fair amount of experience already. I realise that using this particular OS may seem like overkill for what I currently wish to do with it (stream content to other devices and backup) but as I can get a copy for free it seems sensible. Edit: From reading answers posted I feel I should give more information. I have now tried to add a static IP address using my router configuration settings. I have used the getmac command to get the mac address of the server. My ISP is Virgin Media and I have gone to the LAN IP section and I have added an IP address to the DHCP Reservation Lease Info. I can now use remote desktop connection internally to remote to the server (so I am assuming assigning this IP has worked). How do I configure this on the OS as well? I am also unsure on how I would remote to this machine outside of my local network?

    Read the article

  • virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

    - by Chris Gow
    Hi: I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

    Read the article

  • Accessing clearcase view drive from virtual machine is slow

    - by PermanentGuest
    I have a windows XP virtual machine running under a Windows XP host. On the host : On the host clearcase 7.1.1.2 is installed. I have a dynamic view mapped onto some drive. The view has certain VOB/directory structure where my application DLLs from the nightly build and config files are stored. I run my application on the host machine which uses the DLLs and config files from the VOB and everything runs smooth. Now I want to move this set-up to a virtual machine. On the guest : I'm running the guest with a vm-player. I don't want to install clear-case on this as I don't want to expose this machine onto the network. The network setting in the guest is 'host-only'. I have mapped the host's clearcase view drive as a shared folder and I'm able to access this drive from the virtual machine. Also, the application is running. However, the problem is that the access of the clearcase drive from the virtual machine is very slow. I can experience this from the windows explorer. Due to this, the starting of my application takes several seconds in the virtual machine while on the guest it comes up pretty fast. My question is : Is there any way to speed up the performance? I have managed to copy some of the DLLs which don't change frequently to the virtual machine to improve the performance. However, there are still lot of DLLs which have to be taken from the clearcase drive as they change frequently. VMplayer version is : VM Player 3.0.1 build-227600 Both guest and host is : Windows XP service pack 3 Host clearcase is : clearcase 7.1.1.2

    Read the article

  • sbs-server with 2 nics and 2 connections to the internet with different providers not working as it

    - by erik-van-gorp
    We have the following configuration : A sbs-2003 server in a domain (mydomain.com) with 2 network cards, each connected to a different network (provider), with different gateways, one for web and one for mail and clients. (we do this because the bandwitdh we get from our providers is too small to handle all the mail(+spam) traffic and webservices, so we took 2 providers) DNS is as follows : www.mydomain.com 1.2.3.4 mail.mydomain.com 5.6.7.8 NIC 1(192.168.1.3) is connected to to the internet through a firewall at 192.168.1.1, having wan address 1.2.3.4 NIC 2(10.0.0.3) is connected to to the internet through a firewall at 10.0.0.1, having wan address 5.6.7.8 Both nics have their default gateway installed at their corresponding routers. Also the metrics are set equal. (i know this isn't a supported config, but it works more or less). In this configuration i can use RDP on both wan adresses, and telnet to port 25 works as well on both. The issue now is that since a few weeks , we get regular disconnections, and website hickups(timeouts), several per hour. If we set one router to a higher metric, that route no longer works. In short, I want the mails to route through NIC2 and the web through NIC1. Any better configuration (without installing a second mail server) ?

    Read the article

  • Should an HA failover occur in this scenario?

    - by joeqwerty
    I'm running vSphere 5 in an HA cluster across two hosts (vsphereA and vsphereB). I have the HA cluster configured for host monitoring and datastore heartbeat monitoring with admission control disabled (hopefully I rightfully understand that datastore heartbeat monitoring prevents inadvertent and unwanted HA failovers due to management network isolation). Each host has a single connection to a dedicated iSCSI network and iSCSI target (no MPIO). All vmdk's for all VM's exist on the iSCSI datastore. As a test of HA I disconnected the iSCSI connection on vsphereB and was surprised to see that the running VM's on vsphereB continued to run on vsphereB. The powered off VM's were showing as inaccessible (which I expected due to the fact that they weren't running and the connection from vsphereB to the iSCSI target was severed) but the running VM's continued to run and continued to be "owned" by vsphereB. I expected to see an HA failover occur for those VM's and expected to see them "owned" by vsphereA after the HA failover (which didn't occur). I'm at a loss to understand why an HA failover didn't occur for those VM's. Am I misunderstanding in which cases an HA failover should occur?

    Read the article

  • PCs on domain can not resolve external IP addresses using the DC's DNS Server

    - by Ben
    I currently have a domain controller which handles all DHCP and DNS. The DHCP works just fine and the domain controller itself can use the internet with no issues. However, PCs that are part of the domain are not able to use external websites, only internal. Does anyone have any way I can solve this issue? Thank you Server: Windows Server 2008 R2 PC: Win7 Enterprise x64 Edit: (domain controller) C:\Users\bcollyer>nslookup google.com Server: localhost Address: 127.0.0.1 Non-authoritative answer: Name: google.com Addresses: 2a00:1450:4009:809::100e 173.194.41.166 173.194.41.165 173.194.41.169 173.194.41.162 173.194.41.161 173.194.41.160 173.194.41.168 173.194.41.167 173.194.41.164 173.194.41.163 173.194.41.174 Edit 2: C:\Users\bcollyernetstat -rn Interface List 12...30 85 a9 f7 8a 21 ......Atheros AR8161/8165 PCI-E Gigabit Ethernet Control ler (NDIS 6.20) 1...........................Software Loopback Interface 1 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11...00 00 00 00 00 00 00 e0 Microsoft Teredo Tunneling Adapter IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.0.67 172.16.0.202 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.0.0 255.255.0.0 On-link 172.16.0.202 276 172.16.0.202 255.255.255.255 On-link 172.16.0.202 276 172.16.255.255 255.255.255.255 On-link 172.16.0.202 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.0.202 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.0.202 276 Persistent Routes: None IPv6 Route Table Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link Persistent Routes: None BTW I have no javascript on the server so can't reply to individual answers... Sorry!

    Read the article

  • Deleted printers keeps coming back - and multiply

    - by MojoDK
    My users are on 2012 R2 RDS Session Host servers. I've used "Deploy Printers" (from Print Manager) to deploy 4 printers. The last week, I've had a lot of problems where users can't print. If I deleted the printer and added it again, they could print just fine. Now I've removed all printer deploying from GPO - and I have no printers in any login scripts. I did a gpupdate /force, but all the 4 printers are now listed 3 times... If I delete the printers and log off and back on, all the printers are popping up again. Sigh! This is driving me nuts. This script doesn't show any of the "SVFREJA" printers... Set objWMIService = GetObject("winmgmts:\\.\root\cimv2") Set colPrinters = objWMIService.ExecQuery ("Select * From Win32_Printer") If colPrinters.Count <> 0 Then 'If there are some network printers Dim s s = "" For Each objPrinterInstalled In colPrinters ' For each network printer s = s + objPrinterInstalled.Name + chr(13) Next msgbox s End if It gives me this result... (sry for the big picture) My problem is not with the "redirected" printers, my problem is that I have several printers with the same name (on SVFREJA) and I can't get rid of them. Any idea why I can't get rid of the "ophaned" printers??

    Read the article

  • Netgear router is not resolving hostnames

    - by Thomas Clayson
    Not sure what the problem is, but I am used to being able to access other clients on my LAN via their hostname. We got a new router from plusnet (Netgear WNR1000v3) and now this has stopped working. For instance, if I were to run a web server from one computer with the hostname TomPC usually I could go into a browser and type http://TomPC and I would get the web server front page. I can access it by using the LAN ip of the machine. e.g. http://192.168.1.1 works fine. I thought it would be a simple option in the admin panel of the router - possibly I had to turn on DNS/DCHP or something. But I can't see anything, and my searches on the internet seem to turn up ridiculous solutions involving setting up a dedicated DNS server on my LAN. This is just a small home network - really I just want to be able to access my Raspberry PI on the network without having to work out the IP address every time. (I know I could just set a static IP address for it, but using its hostname would be much easier). DCHP is enabled in the LAN settings part, although RIP is disabled (I don't know what the latter is) I don't know if this has anything to do with it? Many thanks!

    Read the article

  • Ubuntu in failed state after upgrade from 10.04 to 10.10 - How to recover?

    - by Harvey
    I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: 1. Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a). 2. gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok] 3. gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ... What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

    Read the article

  • esx5 debian VM vlan setup

    - by Kstro21
    i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

    Read the article

  • SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database

    - by eulerfx
    I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

    Read the article

  • Can not open ports in iptables on CentOS 5??

    - by abszero
    I am trying to open up ports in CentOS's firewall and am having a terrible go at it. I have followed the "HowTo" here: http://wiki.centos.org/HowTos/Network/IPTables as well as a few other places on the Net but I still can't get the bloody thing to work. Basically I wanted to get two things working: VNC and Apache over the internal network. The problem is that the firewall is blocking all attempts to connect to these services. Now if I issue service iptables stop and then try to access the server via VNC or hit the webserver everything works as expected. However the moment I turn iptables back on all of my access is blocked. Below is a truncated version of my iptables file as it appears in vi -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5801 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5901 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 6001 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5900 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT Really I would just be happy if I could get port 80 opened up for Apache since I can do most stuff via putty but if I could figure out VNC as well that would be cool. As far as VNC goes there is just a single/user desktop that I am trying to connect to via: [ipaddress]:1 Any help would be greatly appreciated!

    Read the article

  • How can the route between two private IPs go via public IPs?

    - by Gilles
    I'm trying to understand what this output from traceroute means. I changed the IP addresses for privacy but retained the public/private IP range distinction. traceroute.db -e -n 10.1.1.9 traceroute to (10.1.1.9), 30 hops max, 60 byte packets 1 10.0.0.1 0.596 ms 0.588 ms 0.577 ms 2 10.0.0.2 1.032 ms 1.029 ms 1.084 ms 3 10.0.0.3 3.360 ms 3.355 ms 3.338 ms 4 23.0.0.4 3.974 ms 4.592 ms 4.584 ms 5 23.0.0.5 13.442 ms 13.445 ms 13.434 ms 6 45.0.0.6 13.195 ms 12.924 ms 12.913 ms 7 67.0.0.7 52.088 ms 51.683 ms 52.040 ms 8 10.1.1.8 46.878 ms 44.575 ms 44.815 ms 9 10.1.1.9 45.932 ms 45.603 ms 45.593 ms The first 10.0.* range is inside my organisation. The last 10.1.* range is another site of my organisation. The intermediate addresses belong to various ISPs. I expect that there is some kind of VPN between the two sites, but I don't know much about our network topology. What I don't understand is how the route can go from a private address through public addresses back into private addresses. Searching led me to Public IPs on MPLS Traceroute, which gives a possible explanation: MPLS. Is MPLS the only possible or most likely explanation? Otherwise what does this tell me about our network infrastructure? Bonus question for my edification: in this scenario, who is generating the ICMP TTL exceeded packets and if relevant mangling their source and destination addresses?

    Read the article

  • Print from Linux to Windows networked printer

    - by wonkothenoob
    I want to print from a Debian (Lenny) workstation to a Windows networked printer. I'm not even sure what type of Windows network this is. Our tech-support is friendly but doesn't want to get involved with supporting Linux. I need to use it for a variety of reasons and am completely stumped because I know nothing about Windows networking. They gave me URI smb://msprint.ourorg.edu as the "address" of the printer and further confirmed that the domain is "OURORG" and the share is "PHYS-PRI". I've installed CUPS and made sure that it's running as a daemon, I've clicked on the system-config-printer[1] icon, selected the printer as a Windows printer shared via SAMBA and entered the above URI. Attempting to print a testpage just sees it sit in the queue. I attempted to see if I could access the share using two other methods. Method 1. First I tried the "smbclient" from the CLI: $ smbclient -L //msprint.ourorg.edu -U user23 timeout connecting to 192.168.44.3:445 timeout connecting to 192.168.44.3:139 Connection to msprint.ourorg.edu failed (Error NT_STATUS_ACCESS_DENIED) Method 2. I tried to use the GUI tool Smb4K. This shows me four other toplevel (I'm assuming they're domains?) groupings one of which is the one which our IT department supplied to me. Clicking them shows a bunch of other machines with (what I assume are NetBIOS names?) including my own. I see all sorts of other networked printers belonging to other departments but none within mine. Certainly not the PHYS-PRI one suggested to me by the IT folks. I realize that I'm probably using the wrong terminology for the windows network, but can anyone help me with this? What steps should I be taking in debugging this? Do I need to actually run my machine as a SAMBA server to authenticate to the printer or should I just be able to communicate using CUPS? It's a GUI to CUPS configuration http://cyberelk.net/tim/software/system-config-printer/

    Read the article

  • Cannot Connect To VMWare Guest OS Using NEither RDP Nor

    - by Humanier
    Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

    Read the article

< Previous Page | 587 588 589 590 591 592 593 594 595 596 597 598  | Next Page >