Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 591/729 | < Previous Page | 587 588 589 590 591 592 593 594 595 596 597 598  | Next Page >

• Driver corruption when deploying Dell Touchpad Drivers (with software) during imaging process

  - by BigHomie

  We're an sccm shop, and use it to deploy Windows. When deploying Dell laptops (multiple models), the touchpad drivers seem install properly, but the software doesn't. The resulting problem is that when the touchpad is pressed on occasion, the mouse pointer will 'jump' to certain points on the screen. A possible symptom of this problem/visible sign is if the touchpad icon isn't in the system tray. The software is in the control panel, but when opened part of the gui is pixelated, indicating botched install maybe? The manual resolution to this, is to go into device manager and uninstall the driver with the option to uninstall all driver software. After a restart, the driver and software is apparently reinstalled, and from there works as expected. Obviously this partially defeats the purpose of a zero touch deployment. If anyone knows why this is and/or a possible workaround, those answers would be valid as well. Barring that, I want to find a way to deploy the driver and touchpad software in an unattended way, so that it can be conditionally installing during the imaging process. To be honest I'm not sure how to troubleshoot this, I suppose I could try drvinst.exe to install the driver, but finding out why this fails initially would keep me from spinning my wheels.

  Read the article

• Problems reviving old pc including graphics card issue.

  - by Mick

  I have a PC that seemed to have died years ago that I am trying to revive. It has a dual core athlon processor and a gigabyte motherboard. It had two dual output graphics cards, and I have long since forgotten which output would print out the diagnostic information as the PC starts up. Also I suspect that the resolution set on all the monitors was probably higher than my current single monitor is capable of displaying. The motherboard also has a built in graphics card, so I thought it may be simplest to remove both the graphics cards and plug my monitor into the onboard graphics just while I get things going. Does that seem sensible? Now the other problem: The PC has two hard drives. I have no idea which one is the primary one it is attempting to boot from. When I power up, the fan comes on and I hear some chuga-chuga-pause chuga-chuga-pause repeat indefinitely. I'm not sure which device is making the noise. There are no-beeps at any time. I see nothing on the screen at any time, not even for a second. Any suggestions? EDIT: If T start up the PC without the power connected to the CDrom there is no chuga-chugan noise.

  Read the article

• Using GPO to collect data about VMware view activity

  - by MoSiAc

  Our security group wants us to begin logging data for external access to our view enviroment. At first we thought that view security would be logging all source ip's that are external in nature so if for some reason there is an intrusion we would have record of it there. Of course our firewall logs all that information but correlating it to view is sketchy at best with our current implementation. We know on viewdesktops there is a set of keys in VolitateEnviroment that contains stuff such as source ip and username, etc. We have a script in place that, when run as a logon script attached to a user account in AD collects the information as we need it. If we have a GPO run the same script the information does not get collected. We feel like there is a piece of the puzzle we're missing but we don't know what. If anyone knows what we're forgetting or misconfiguring that would be great, or if you have a better way of us collecting external source ip's for view specifically we'd be interested in that as well. Thanks, EDIT CODE Batch script to dump to text file @echo off timeout 20 echo %computername%/%username% %time% %date% c:\vdi\vmware.txt echo ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~c:\vdi\vmware.txt reg query "HKEY_CURRENT_USER\Volatile Environment" /v "ViewClient_LoggedOn_Username"c:\vdi\vmware.txt reg query "HKEY_CURRENT_USER\Volatile Environment" /v "ViewClient_IP_Address"c:\vdi\vmware.txt echo.c:\vdi\vmware.txt VB Script to display values Const HKEY_CURRENT_USER = &H80000001 Set wmiLocator=CreateObject("WbemScripting.SWbemLocator") Set wmiNameSpace = wmiLocator.ConnectServer(".", "root\default") Set objRegistry = wmiNameSpace.Get("StdRegProv") sPath = "Volatile Environment" lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_Machine_Name", vMachine) lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_IP_Address", vIP) lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_MAC_Address", vMAC) msgbox "The Remote Device Name is " & vMachine & " @ " & vIP & " (" & vMAC & ") " he wanted me to mention that the batch file actually runs and I can see it counting down when I reconnect but it does not grab the registry values.

  Read the article

• Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

  - by user12844

  I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

  Read the article

• Last step in HDD Recovery (fixing windows)

  - by Atom Computing

  My dad’s hard drive corrupted which was a result of many bad sectors. Anyway, I made a clone of the drive and have now repaired it totally (recreating the MBR and MFT) and doing a series of ChkDsk's on it. I can now see all the files and folder on it and it is all intact. I currently have it as a slave in my computer (where I was doing all the repairs). When putting it back into the computer, it comes up with "A disk read error occurred: Press Ctrl + Alt + Del to Restart". I don’t know why this is happening but think it might have something to do with file permissions. I have tried a start-up recovery on the Vista boot CD and it found no problems. When trying to apply file permissions (and creating file perms for the SYSTEM group (as it didn’t have any for SYSTEM group)) it couldn't apply them for some of the System32 folder files. I have tried applying them as admin and with as powerful privileges I can get. All to no avail. When it is in my PC I can boot it up (I added it into my bootloader) and it boots up fine except when it logs in it comes up with the error - "Rundll32.exe - Windows cannot access the specified device, path or file. You may not have the appropriate permissions to access the item" This message keeps coming back and nothing loads at all. Any help would be greatly received as I have got so far with the data recovery and want to avoid a reformat at all costs due to the vast number of programs installed and I don’t have much time on my hands! Thanks

  Read the article

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• Microphone array support in Windows. Info on performance and compatible hardware?

  - by exinocactus

  It is officially claimed by Microsoft (Audio Device Technologies for Windows), that Windows Vista has an integrated system-level support of microphone arrays for improved sound capturing by isolating a sound source in target direction and rejecting ambient noise and reverberation. In more technical terms, an implementation of an adaptive beamformer. Theoretically, microphone arrays with 2-4 mics can substantially improve SNR under some conditions like speaker in front of the laptop in noisy environment (airport, cafe). Surprisingly, though, I find very little information about commercially-available products supporting these new features. I mean products like portable usb micropone arrays or laptops or flat screens with integrated mic arrays. I could only find info about two laptop models having "noise cancelling digital array microphone". These are Dell Latitude and Eee PC 1008P-KR. Now my questions: Do you have any experience with the Windows beamformer implementation? For instance, in the above mentioned laptops. How well does it work? Are there any tests results available in the net or in print (papers?)? Do you know about other microphone array hardware? What could be the reason why mic array technology didn't get sucess Is there mic arrays support in 'Windows 7'?

  Read the article

• Tried to install Mint to a Flash Drive. Now I can't boot from the main hard disk.

  - by Dan

  Hello, all. I'm kind of new to Linux and I need some help. I wanted to install a Linux distro to a flash drive so that I can have a portable OS with all my settings, programs, etc. wherever I go. So I fired up a Linux Mint Live CD and installed Mint to the flash drive, and this seems to work OK. But now, whenever I try to boot up my system normally without the flash drive plugged in, it doesn't seem to work. It basically hangs for a bit, and then I get the following prompt: error: no such device: (some long hex val) grub rescue> However, when I try powering my system up when the USB is plugged into the computer, it gives me an option between using the OS installed on my USB and the OS installed on my HD. Selecting the latter, everything loads up just fine. I'm guessing that installing Mint to the flash drive somehow messed with my native Grub installation, but, again, I'm kind of new to Linux, so I'm not sure exactly why. Any help is greatly appreciated.

  Read the article

• Ubuntu's garbage collection cron job for PHP sessions takes 25 minutes to run, why?

  - by Lamah

  Ubuntu has a cron job set up which looks for and deletes old PHP sessions: # Look for and purge old sessions every 30 minutes 09,39 * * * * root [ -x /usr/lib/php5/maxlifetime ] \ && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 \ -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir \ fuser -s {} 2> /dev/null \; -delete My problem is that this process is taking a very long time to run, with lots of disk IO. Here's my CPU usage graph: The cleanup running is represented by the teal spikes. At the beginning of the period, PHP's cleanup jobs were scheduled at the default 09 and 39 minutes times. At 15:00 I removed the 39 minute time from cron, so a cleanup job twice the size runs half as often (you can see the peaks get twice as wide and half as frequent). Here are the corresponding graphs for IO time: And disk operations: At the peak where there were about 14,000 sessions active, the cleanup can be seen to run for a full 25 minutes, apparently using 100% of one core of the CPU and what seems to be 100% of the disk IO for the entire period. Why is it so resource intensive? An ls of the session directory /var/lib/php5 takes just a fraction of a second. So why does it take a full 25 minutes to trim old sessions? Is there anything I can do to speed this up? The filesystem for this device is currently ext4, running on Ubuntu Precise 12.04 64-bit. EDIT: I suspect that the load is due to the unusual process "fuser" (since I expect a simple rm to be a damn sight faster than the performance I'm seeing). I'm going to remove the use of fuser and see what happens.

  Read the article

• Prevent rmdir -p from traversing above a certain directory

  - by thepurplepixel

  I hacked together this script to rsync some files over ssh. The --remove-source-files option of rsync seems to remove the files it transfers, which is what I want. However, I also want the directories those files are placed in to be gone as well. The current part of the find command, -exec rmdir -p {} ; tries to remove the parent directory (in this case, /srv/torrents), but fails because it doesn't have the right permissions. What I'd like to do is stop rmdir from traversing above the directory find is run in, or find another solution to get rid of all the empty folders. I've thought of using some kind of loop with find and running rmdir without the -p switch, but I thought it wouldn't work out. Essentially, is there an alternative way to remove all the empty directories under the parent directory? Thanks in advance! #!/bin/bash HOST='<hostname>' USER='<username>' DIR='<destination directory>' SOURCE='/srv/torrents/' rsync -e "ssh -l $USER" --remove-source-files -h -4 -r --stats -m --progress -i $SOURCE $HOST:$DIR find $SOURCE -mindepth 1 -type d -empty -prune -exec rmdir -p \{\} \;

  Read the article

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

  - by chickenloop

  I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

  Read the article

• Bridging networks problems

  - by Eric

  In my setup I have 3 computers and 2 (wireless d-link) routers. Computer1 has ethernet and wireless interfaces ethernet : 192.168.0.x (DHCP) wireless : 192.168.10.254 (static) Computer 2 has ethernet with two ips ethernet1 : 192.168.0.90 (static) ethernet2 : 192.168.10.110 (static) Computer 3 is a particular device with a hardcoded ip that I can't change wireless : 192.168.10.41 (static) Router1 manages internet and DHCP for network 192.168.0.0/24 Router2 is more complicated. I don't use DHCP. I use it to bridge between both networks. Its static ip is 192.168.10.1 Computer1 can ping Computer2. Computer1 can ping Computer3. Computer1 can ping Router1. Computer1 cannot ping Router2. Computer2 cannot ping Computer3. Computer2 can ping Router2. Router1 can ping Router1 Router2 can ping Computer2 Router2 cannot ping Computer1 Router2 cannot ping Computer3 This is very weird. Router2 manages the wireless connection, it should be able to ping its own computers right? My question is obviously : How can I make it so Computer2 can access everything else. This is a traditional case of "it was working before christmas and now it doesn't". The ethernet wiring is as follow : [ Computer1 ]----[ Router1 ]---[ Router2 ]---[ Computer3 ] I am using switch (lan) ports on Router1/2.

  Read the article

• Why does the wireless network icon have a red X over it when everything seems to work?

  - by Kristo

  I booted my almost brand new laptop running Windows 7 this morning and noticed a red X through the wireless networking icon in the system tray. At first I thought something was wrong, but clicking on it shows a good connection to my wireless network. I had no problem getting here to post this question. I'm very new to Windows 7 so I have no idea how to troubleshoot this myself. Is there an actual problem here? Can I fix the icon so it doesn't falsely display an error (I assume that's what the red X means)? Here's what I know: I can get here to post this question. There's at least one unsecured network available that I'm not connected to. I can see a bunch of wireless networks, presumably from my neighbors' houses. There are no other computers turned on in my house right now. The device manager shows no problems with any devices. I can ping my default gateway, DNS, and yahoo.com with no problem.

  Read the article

• Corsair SSD appears completely blank and does not retain written data

  - by ebanders

  I have a 180GB Corsair SSD (model# CSSD-F180GB2-BRKT) as the primary drive in a Windows laptop. Recently the machine became unbootable after installing Windows updates. Windows installed updates before the machine shut down and the next time the machine boot up it complained about not being able to find a bootable device. After finding fixmbr unsuccessful at making the machine unbootable, I investigated a little within knoppix. Fdisk revealed an empty partition table. A scan by Testdisk came up empty. And finally 'head -c 1024 | hd' reveals all zeros. Creating a primary partition spanning the whole disk completes successfully, but after a reboot the disk appears empty again. dmesg reveals no read or write errors. smartctl indicates that the drive is healthy- although the SMART attribute values do not appear to be read properly. "Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO" and "Threshold Page | INCONSISTENT IDENTITIES IN THE DATA" messages appear within the table of values. I don't have much experience with SSDs. Is this drive dead or something? Can anyone recommend any diagnostic tools that may be suited for diagnosing SSDs?

  Read the article

• SSD won't boot anymore

  - by LordrAider

  Yesterday I put the computer to sleep. Something went wrong because it didn't go fully to sleep. So I restarted the pc and now it won't boot windows 7 anymore. It said : "Please insert valid boot device". I ran Windows 7 restore disc and tried restoring, first it said, mbr fixed. No result but now it said : "Operating system could not be loaded" I ran Windows 7 restore disc again and then it said something about a corrupt partition and that he fixed it. But got the same msg at restart about operating system not found. I ran Windows 7 restore disc again and used diskpart and watched the volumes. My SSD shows up as RAW filesystem... not as NTFS. The size of the disk seems correct. In the bios it also shows up as Healthy disk. What could went wrong and could I recover data with testdisk? I assume something went wrong with the partition :(. It's a Plextor SSD 256M2P SSD, only 3 months old. Thx in advance

  Read the article

• Moving from 1 Linux Partition to Many over USB Mount

  - by Mistiry

  We have devices which use Compact Flash for storage. They work OK, but we recently got industrial-grade CF cards to start using. One of the major problems we get is corruption on the flash card. As it is now, these flash cards run Debian with everything in a single partition. We want to have multiple partitions on the new industrial CF cards to help avoid some of the corruption problems. I booted up the device, and attached a USB CF reader. I then used fdisk to partition the CF card in the USB reader. How can I move the data to these partitions so that it works? I have a partition for each of these directories: /lib /var /root /boot /tmp /home /etc / swap space I imagine I can't just use rsync - do I need to attach a second CF reader with a copy of the CF card, so that it's not active and in-use - and then copy from the first reader to the second? How will the system know where to find its files? I know I'd have to change fstab, but that resides in /etc, which will be on a separate partition...how will it find the fstab file if it can't find /etc? And what about grub? I'm at a loss, perhaps its just because I'm under the weather, or I'm just missing a piece of logic here... Any help is greatly appreciated, this is somewhat urgent as our existing stock is nearing its end and we don't want to purchase anything but these industrial cards, but need to get it working with partitions.

  Read the article

• Determining how all memory is used in Windows Server 2008

  - by Mojah

  Hi, I have a Windows Server 2008 system, which has 12GB of RAM. If I list all processes in the Task Manager, and SUM() the memory of each process (Working Set, Memory (Private Working Set), Commit Size, ...), I never reach more than 4-5GB that should be "in use". However, task manager reports this server has 11GB in use via the "Performance" tab. I'm failing in determining where all that used RAM is going. It doesn't seem to be system cache, but I can not be sure. It might be a memory leak in one of the appliances, but I'm struggling to find out which one. The server's memory keeps filing up, and eventually forces us to reboot the device to clear it. I've been reading up on how RAM assignments work on Windows Server: RAM, Virtual Memory, Pagefile and all that stuff: http://support.microsoft.com/kb/2267427 What's the best way to measure? http://www.zdnet.com/blog/bott/windows-7-memory-usage-whats-the-best-way-to-measure/1786 Configure the file system cache in Windows: http://smallvoid.com/article/winnt-system-cache.html But I fear I'm stuck without ideas at the moment.

  Read the article

• Laptop freezing every few seconds, including screen + sound

  - by zenstealth

  Just a few days ago, my Windows 7 HP dv4170us (1.76Ghz CPU, 1GB Ram) laptop started to freeze every other second where everything on screen and and sound (such as a song playing in iTunes) would just freeze until I bash it violently (without actually breaking the laptop) or wait for a couple of more seconds. I think it started one night when I noticed that a USB mouse of mine stopped working, and it displayed random "Device was not recognized" errors. I just unplugged the mouse and ignored it. Skip forward to the next day, is started freezing, and as of today I can't get my computer to not keep freezing. I tried to backup my files onto an external hdd, but it almost corrupted the drive. I ran 4 complete virus scans using MSSE and MalwareBytes (both quick and full scans), and they all came up clean. In the Task manager, the CPU usage is on a constant max, and so is the RAM (if I have just a few apps running, I only have like 30Mb of free RAM left). Also, on the outside of my laptop, right above where the CPU is located, it's very, very hot. I suspect that something is wrong internally within inside of the computer, but I'm not sure. It also does the same thing when booted into Ubuntu.Does anyone know what could be wrong with it?

  Read the article

• How do I re-configure grub options

  - by Ash

  I've searched this topic and I can't find an article with a plausable solution, to my problem. I installed windows 7 first, with 100gb of disk space. I created the necessary partitions via windows. Then I installed Ubuntu 12.04 on the remaining 400gb of disk space. During the Ubuntu installation I installed the ubuntu boot loader on /dev/sda3 which Windows (as expected never granted me the option pre-boot for which OS I wanted to boot). So I re-installed Ubuntu on that /dev/sda3 partition, overriding the windows 7 loader. Now when I boot windows 7, it runs GNU Grub, so like an infinite loop. How can I reconfigure grub to say: /dev/sda is the bootloader. /dev/sda2 is Windows. /dev/sda3 is Ubuntu. Re-installing windows and my partitions isn't an option, purchasing software for windows isn't an option (theres a reason I use linux, it's not because it's free, because you don't have to install lots of shit to get stuff working, and over-all it's a robust OS).

  Read the article

• How to fix missing RAID1 drive

  - by Sodved

  I had to do some fiddling about with my cables inside thebox and now I am getting a "Critical Error" about the RAID disks during startup. I have a gigabyte GA-MA770T-UD3 motherboard. Aparently the RAID controller is an AMD SB710 chip. I'm pretty sure I know what happenned. The first time I rebooted I had forgotten the power cable on one of the disks in the RAID1 (mirror) and let it boot up. So I shut down and put the power back in. So now when it boots up I go into the RAID admin interface (between the BIOS screen and the OS loading): it shows the RAID1 as in error the logical device has one disk and says the other is disconnected or missing the other physical disk shows up as a single disk If I boot to the OS (Windows 7 32 bit) the data all seems to be there. If I go into computer management it says my partition is on a disk and working OK. But the other disk is offline because: "The disk is offline because it has a signature collision with another disk that is online" So I am guessing because I STUPIDLY booted up with only one of the disks powered on, the other disk fell out of synch with the mirror and so now cannot rejoin the mirror. How do I fix this? I want to get the RAID1 mirror working again. There does not appear to be any "Repair" option in the basic RAID admin tool which I get into during startup before the OS boots. I have not made any explicit changes to the online one (but I guess the OS has probably written some admin data).

  Read the article

• Performance of external USB disk with ESXi5

  - by PeterMmm

  I have a new HP DL120 G7 server with ESXi5. One VM is a Win2003 instalation and I have an external USB2.0 drive attached by USB Controller and USB Device. I copy a 4GB file from external USB to server disk. In the VM that takes up to 10 minutes. On a native Win2003 that takes aprox. 3 minutes. I have no explaination for that diference: In any case the bottleneck is the USB connection, much slower than the disks (SAS, RAID1). If the USB connection on the VM would be USB1.1 and not USB2.0 it would take much more time. (The disk performance between server partitions on the VM is correct. - see update) Could be that my native box is extremely fast and the VM is the normal case. ??? Update I try with passtrough and a first run copy the same data in aprox. 7 minutes. Still 2 times slower than the native connection. I also did another messure and the copy between partitions on the same VM takes 3 minutes.

  Read the article

• Killing a process which ran for a lot of time or is using a lot of memory

  - by Vedant Terkar

  I am not sure whether this question belong to Stack Overflow or here, but here we go. I am designing a online 'C' compiler, which will compile and invoke the program if compilation succeeded. So here is code which I am using for that: $str=shell_exec("gcc path/to/file.c -o path/to/file.exe 2>&1"); if(file_exists("path/to/file.exe")){ $res=shell_exec("path/to/file.exe <inputfile 2>&1"); echo $res; } This Seems to work fine with simple program files. But When file.c That is the source code entered contains Infinite loop then This script crashes the server and utilizes a lot of memory and time. So here is my question: Is There any way to detect for how much time does the process file.exe is Running? How Much Space is Utilized by that process that is file.exe? Is There any way to kill the process file.exe if space and time utilization increases beyond certain limit? That Mean if we allocate time of 2.5sec and space of 40Mb at max for that process file.exe and if any one of those 2 constraints is violated then we should display appropriate error message to client Is it possible? I am Using WAMP (Windows 7).

  Read the article

• Allow connections to only a specific URL via HTTPS with iptables, -m recent (potentially) and -m string (definitely)

  - by The Consumer

  Hello, Let's say that, for example, I want to allow connections only to subdomain.mydomain.com; I have it partially working, but it sometimes gets in a freaky loop with the client key exchange once the Client Hello is allowed. Ah, to make it even more annoying, it's a self-signed certificate, and the page requires authentication, and HTTPS is listening on a non-standard port... So the TCP/SSL Handshake experience will differ greatly for many users. Is -m recent the right route? Is there a more graceful method to allow the complete TCP stream once the string is seen? Here's what I have so far: #iptables -N SSL #iptables -A INPUT -i eth0 -p tcp -j SSL #iptables -A SSL -m recent --set -p tcp --syn --dport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK SYN,ACK --sport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK ACK --dport 400 #iptables -A SSL -m recent --remove -p tcp --tcp-flags PSH,ACK PSH,ACK --dport 400 -m string --algo kmp --string "subdomain.mydomain.com" -j ACCEPT Yes, I have tried to get around this with nginx tweaks, but I can't get nginx to return a 444 or abrupt disconnect before the client hello, if you can think of a way to achieve this instead, I'm all ears, err, eyes. (As suggested by a user, bringing this inquiry over from http://stackoverflow.com/questions/4628157/allow-connections-to-only-a-specific-url-via-https-with-iptables-m-recent-pote)

  Read the article

• Determining how all memory is used in Windows Server 2008

  - by Mojah

  I have a Windows Server 2008 system, which has 12GB of RAM. If I list all processes in the Task Manager, and SUM() the memory of each process (Working Set, Memory (Private Working Set), Commit Size, ...), I never reach more than 4-5GB that should be "in use". However, task manager reports this server has 11GB in use via the "Performance" tab. I'm failing in determining where all that used RAM is going. It doesn't seem to be system cache, but I can not be sure. It might be a memory leak in one of the appliances, but I'm struggling to find out which one. The server's memory keeps filing up, and eventually forces us to reboot the device to clear it. I've been reading up on how RAM assignments work on Windows Server: RAM, Virtual Memory, Pagefile and all that stuff: http://support.microsoft.com/kb/2267427 What's the best way to measure? http://www.zdnet.com/blog/bott/windows-7-memory-usage-whats-the-best-way-to-measure/1786 Configure the file system cache in Windows: http://smallvoid.com/article/winnt-system-cache.html But I fear I'm stuck without ideas at the moment.

  Read the article

< Previous Page | 587 588 589 590 591 592 593 594 595 596 597 598  | Next Page >