Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 588/729 | < Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >

• IDE compatability with SATA image

  - by Ormis

  We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

  Read the article

• iCloud backup merges or overwrites?

  - by Joe McMahon

  The following happened today (it was six AM my time, so yeah, I was dumb and dropped stitches in this process): A friend had a problem with her iPhone and needed to reset it. Unfortunately she did the reset while connected to iTunes and the restore process kicked in. In my sleepy state, I told her to go ahead. She did, and restored the most recent local (iTunes) backup (from July last year - she doesn't back up often, as she has an Air which is pretty full). During setup on the phone, she was prompted to merge data with the iCloud copy, and did so. There was no "restore from iCloud" prompt. Obviously I should have made sure she was disconnected from iTunes before she did the reset, or had her set it up as a new device and then restored from iCloud, but water under the bridge now. (Side question: could I have had her disconnect and then restart the phone again and avoid this whole process?) The question is: was the "merge" that happened in this process a true merge, or a replace? Her passwords for Mail were wrong, since they were the old ones from the old backup. If she does the wipe data and restore from iCloud, will she get her old SMSes and calendar entries back? Or did the merge decide that the phone, despite it being "old" was right and therefore the SMSes, calendar entries, etc. were discarded? As a recovery option, I have a 4-day-old iTunes backup here from ~/Library/Application Support/MobileSync/Backup, but she and the phone are 3000 miles away, and it's 8GB, so I can't easily restore it for her. I do have the option of encrypting it and mailing it on a data stick if the iCloud backup is now toast. Should she try the wipe and restore from the cloud (after backing up locally), or should I just get the more-recent backup in the mail? My goal is to get everything (especially the SMSes) back to the most recent version possible.

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• Unable to resize ec2 ebs root volume

  - by nathanjosiah

  I have followed many of the tutorials that pretty much all say the same thing which is basically: Stop the instance Detach the volume Create a snapshot of the volume Create a bigger volume from the snapshot Attach the new volume to the instance Start the instance back up Run resize2fs /dev/xxx However, step 7 is where the problems start happening. In any case running resize2fs always tells me that it is already xxxxx blocks big and does nothing, even with -f passed. So I start to continue with tutorials which all basically say the same thing and that is: Delete all partitons Recreate them back to what they were except with the bigger sizes Reboot the instance and run resize2fs (I have tried these steps both from the live instance and by attaching the volume to another instance and running the commands there) The main problem is that the instance won't start back up again and the system error log provided in the AWS console doesn't provide any errors. (it does however stop at the grub bootloader which to me indicates that it doesn't like the partitions(yes, the boot flag was toggled on the partition with no affect)) The other thing that happens regardless of what changes I make to the partitions is that the instance that the volume is attached to says that the partition has an invalid magic number and the super-block is corrupt. However, if I make no changes and reattach the volume, the instance runs without a problem. Can anybody shed some light on what I could be doing wrong? Edit On my new volume of 20GB with the 6GB image,df -h says: Filesystem Size Used Avail Use% Mounted on /dev/xvde1 5.8G 877M 4.7G 16% / tmpfs 836M 0 836M 0% /dev/shm And fdisk -l /dev/xvde says: Disk /dev/xvde: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x7d833f39 Device Boot Start End Blocks Id System /dev/xvde1 1 766 6144000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvde2 766 784 146432 82 Linux swap / Solaris Partition 2 does not end on cylinder boundary. Also, sudo resize2fs /dev/xvde1 says: resize2fs 1.41.12 (17-May-2010) The filesystem is already 1536000 blocks long. Nothing to do!

  Read the article

• Computer randomly shuts itself off

  - by Decency

  I have not been able to determine a pattern for why this happens, despite my best efforts. I've attempted to run it on full power with Prime95 and this doesn't trigger a restart. Generally the restarts occur while I'm playing games, watching videos, or even just having multiple tabs open in a browser. However, I often play processor intense games for hours without any restarts occurring, and sometimes they'll happen 3-4 times in an hour during less intense activity, so I don't think that is the problem. I imagine it has something to do with overheating or power consumption so I've been monitoring CPU temperature and cleaning with compressed air, but the problem keeps happening. I don't know how to track power consumption, and assume that this is the problem. Whenever this occurs, the sound gets stuck in a short loop of whatever was playing at the time, though restarts also occur when nothing is playing. Here is a screenshot of temperatures: and under load: Here's the parts list: http://secure.newegg.com/WishList/PublicWishDetail.aspx?WishListNumber=10546754 As shown in the list, the case includes a 585W Power Supply, which I've been told should be plenty. I built the computer myself with a friend's guidance but it's very possible I did something wrong. Right now I'm looking into ensuring that I have the latest drivers for all components. Any help would be appreciated- thanks.

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• How to tell Linux to explicitly swap out main memory of a suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• How do I get a network printer installed in ubuntu 9.04?

  - by SoaperGEM

  My girlfriend's work computer now has Linux on one of the partitions, and for the most part it's running fine--except that I can't seem to get the network printers configured right. There are two of them: a Lanier MP 7500/LD275 and a Lanier MP C3000/LD430c, and Linux seems to have found them both automatically. I'll go through the steps of what I did, and what exactly went wrong. I went to Administration Printing, and clicked the new printer button. It searched for printers and found them both, listed under "Network Printers." I added them as new printers in succession. However, when I clicked "Print a Test Page," it failed saying there was a broken pipe. The device URIs were saved as socket://[ip address]:9100. I changed these to lpd://[ip address] per some online tutorial, which at first looked like it might have worked (but didn't). Then when I tried to print a test page, it first said Processing (and sometimes even Processing - printing test page, 4%, but always subsequently displays Idle - /usr/lib/cups/backend/lpd failed. Help! What do I do? It seems like Linux can find these printers just fine, and the drivers seem to be in place, so what's going wrong?

  Read the article

• Windows 7 Media Center: sometimes no sound on a TV channel

  - by torbengb

  Problem Sometimes, recorded TV shows have no sound. This is of course very annoying because the recorded show is worthless. Also, when switching channels while watching live TV, sometimes a channel has no sound. This is always solved by switching channel again and then back (most often, once will do the trick). Media Center doesn't do this trick by itself when recording of course, so that's the bigger issue - but the cause is certainly the same. Details The computer is running a newly installed Windows 7 and Windows Media Center. It has 2 different tuner-cards installed. Both are installed with signed and up-to-date Win7 drivers and appear OK in Device Manager. Both tuners get the same antenna signal, from a split cable from the wall. The cable delivers analog cable TV (40+ channels) and digital cable TV (4 channels) at the same time. Both tuners have been configured to receive both analog and digital channels. This only happens with analog channels. How can I fix the no-sound problem? Update: I've now spent some time with the computer to try and pinpoint the problem, but I've had little success so far: I flipped through the channels until one didn't have sound, then I disconnected the antenna cable from one of the tuners. It was the right one because then the video also went away. I flipped lots more channels to see if the other card also would come up mute once but I never had a channel without sound. It might still be possible, I don't know. Then I disconnected the "good" tuner and connected the "bad" tuner and again flipped lots of channels but again I never had a channel without sound. It seems to me that the problem is erratic. It happens on any channel, and I haven't ruled out yet that it only happens on one tuner.

  Read the article

• RAID degraded on Ubuntu server

  - by reano

  We're having a very weird issue at work. Our Ubuntu server has 6 drives, set up with RAID1 as follows: /dev/md0, consisting of: /dev/sda1 /dev/sdb1 /dev/md1, consisting of: /dev/sda2 /dev/sdb2 /dev/md2, consisting of: /dev/sda3 /dev/sdb3 /dev/md3, consisting of: /dev/sdc1 /dev/sdd1 /dev/md4, consisting of: /dev/sde1 /dev/sdf1 As you can see, md0, md1 and md2 all use the same 2 drives (split into 3 partitions). I also have to note that this is done via ubuntu software raid, not hardware raid. Today, the /md0 RAID1 array shows as degraded - it is missing the /dev/sdb1 drive. But since /dev/sdb1 is only a partition (and /dev/sdb2 and /dev/sdb3 are working fine), it's obviously not the drive that's gone AWOL, it seems the partition itself is missing. How is that even possible? And what could we do to fix it? My output of cat /proc/mdstat: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid1 sda2[0] sdb2[1] 24006528 blocks super 1.2 [2/2] [UU] md2 : active raid1 sda3[0] sdb3[1] 1441268544 blocks super 1.2 [2/2] [UU] md0 : active raid1 sda1[0] 1464710976 blocks super 1.2 [2/1] [U_] md3 : active raid1 sdd1[1] sdc1[0] 2930133824 blocks super 1.2 [2/2] [UU] md4 : active raid1 sdf2[1] sde2[0] 2929939264 blocks super 1.2 [2/2] [UU] unused devices: <none> FYI: I tried the following: mdadm /dev/md0 --add /dev/sdb1 But got this error: mdadm: add new device failed for /dev/sdb1 as 2: Invalid argument Output of mdadm --detail /dev/md0 is: /dev/md0: Version : 1.2 Creation Time : Sat Dec 29 17:09:45 2012 Raid Level : raid1 Array Size : 1464710976 (1396.86 GiB 1499.86 GB) Used Dev Size : 1464710976 (1396.86 GiB 1499.86 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 15:55:07 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : lia:0 (local to host lia) UUID : eb302d19:ff70c7bf:401d63af:ed042d59 Events : 26216 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 0 0 1 removed

  Read the article

• How to reduce celeryd memory consumption?

  - by Gringo Suave

  I'm using celery 2.5.1 with django on a micro ec2 instance with 613mb memory and as such have to keep memory consumption down. Currently I'm using it only for the scheduler "celery beat" as a web interface to cron, though I hope to use it for more in the future. I've noticed it is the biggest consumer of memory on my micro machine even though I have configured the number of workers to one. I don't have many other options set in settings.py: import djcelery djcelery.setup_loader() BROKER_BACKEND = 'djkombu.transport.DatabaseTransport' CELERYBEAT_SCHEDULER = 'djcelery.schedulers.DatabaseScheduler' CELERY_RESULT_BACKEND = 'database' BROKER_POOL_LIMIT = 2 CELERYD_CONCURRENCY = 1 CELERY_DISABLE_RATE_LIMITS = True CELERYD_MAX_TASKS_PER_CHILD = 20 CELERYD_SOFT_TASK_TIME_LIMIT = 5 * 60 CELERYD_TASK_TIME_LIMIT = 6 * 60 Here's the details via top: PID USER NI CPU% VIRT SHR RES MEM% Command 1065 wuser 10 0.0 283M 4548 85m 14.3 python manage_prod.py celeryd --beat 1025 wuser 10 1.0 577M 6368 67m 11.2 python manage_prod.py celeryd --beat 1071 wuser 10 0.0 578M 2384 62m 10.6 python manage_prod.py celeryd --beat That's about 214mb of memory (and not much shared) to run a cron job occasionally. Have I done anything wrong, or can this be reduced about ten-fold somehow? ;) Update: here's my upstart config: description "Celery Daemon" start on (net-device-up and local-filesystems) stop on runlevel [016] nice 10 respawn respawn limit 5 10 chdir /home/wuser/wuser/ env CELERYD_OPTS=--concurrency=1 exec sudo -u wuser -H /usr/bin/python manage_prod.py celeryd --beat --concurrency=1 --loglevel info --logfile /var/tmp/celeryd.log Update 2: I notice there is one root process, one user child process, and two grandchildren from that. So I think it isn't a matter of duplicate startup. root 34580 1556 sudo -u wuser -H /usr/bin/python manage_prod.py celeryd wuser 577M 67548 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 578M 63784 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 271M 76260 +- python manage_prod.py celeryd --beat --concurrency=1

  Read the article

• Problems with USB-Devices using VDR

  - by emmsinator

  Hey Guys, I'm using VDR on vSphere4. It works sucessfully. I've already backuped several VMs with VDR and I like it very much. But now we got a problem. We have 2 VMs, using an USB-Device Server with a stick plugged in, which is definetely need by these 2 VMs for Licensing and so. Every time, I start the Backup process, the VMs lost the communication to the USB-Server and its stick after building the snapshot and while online. Because of that, the software on these VMs can't work correctly. I have to restart both Machines to solve this problem. These fact is bad for an automatic backup. Does VDR have a special function for those cases or is something like this already known? It would be no problem, to shutdown the servers for building snapshots on Saturday or Sunday. Can VDR initiate a shutdown before starting the backup process? Otherwise I must try to use scripts, but that wouldn't be so nice. Thanks a lot for your help.

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• named responding recursive on norecurse queries

  - by Keks

  I have a server on which named is running. It is intercepted with another named server which it is not aware of. Querying the first named server results in timeouts. The server tries to resolve the query recursively. During that the firewall redirects the DNS Request from the first named server to the second one (the query from the first one is addressed to a e.g. a root server and has its "Recursion desired" bit set to 0). Despite that the second named responds to this request with a entirely or at least 1 level more resolved response than the first named server expects. So it ends up with a timeout even though it got a correct name server or even the full IP for the queried domain. In the first case the first name server tries to follow the authority domain ignoring the coresponding glue record and ends up in a loop it aborts: queried: google.com -> got from named#2: ns1.google.com -> ignore glue record and query: ns1.google.com -> got authority from named#2: google.com In the second case it ignores the answer section with the correct IP and instead tries to follow the name servers from the authority section, which ends up in the same dead end as case 1. So how can it be that the second named responds with recursive results even though the bit was explicitly set to 0 in the request from the first named?

  Read the article

• Installed Windows 7 Ultimate on D Drive and previous Windows 7 Enterprise on C Drive has stopped starting up

  - by teenup

  Please please help! I have installed Windows 7 Ultimate on same hard drive on D Drive on my laptop and the previous Windows 7 Enterprise which was installed on C Drive is not booting up now. When I turn on my laptop, I see two Windows 7 on the screen, when I select newer one, it starts, but when I select older one which is Enterprise edition, system won't start and I get the DOS black screen with this error message: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: Insert your Windows installation disc and restart your computer. Choose your language settings, and then click "Next." Click "repair your computer." Info: The boot selection failed because a required device is inaccessible. I notice that when I run the newer OS installed, the previous OS's drive (Which is D: now instead of C:) has become unusable and when I double click it, it asks me to format the drive. The data, that I had on my D Drive (Which is now C Drive for new OS), I had copied it to a network path and it is available. It was containing Windows 7 Users folder which I copied at that time when installing new windows. I have copied that Users folder again to the new OS's C Drive thinking it would run again, but of no use. Please please please...if someone can help...It is extremely required for me. Thanks a lot in advance.

  Read the article

• Windows 7 breaks even in safe mode

  - by delenda

  Hi, I have a Dell XPS M1730 with Windows 7 installed. I noticed last night that after a few hours of use, the fans kicked into full and I couldn't do anything without it taking forever. Minimising windows, opening device manager or even opening process explorer took minutes and a game install I had just started took nearly 4 hours to complete. When procexp finally loaded, the refresh was so slow that it was mostly useless. From what I could gather, it was reporting 60% idle processes with procexp using nearly 40%. There were no hardware interrupts listed. When I rebooted, the problem went away for about 10 minutes and then the same thing happened. The issue persists in safe mode and even after I removed the graphics drivers, which have been an issue in the past, it still happens. Icons flash quite quickly on the desktop periodically and screen refresh is painfully slow. When booting now, the fans kick in to full as soon as the windows logon box comes up and it's taking 10 minutes to bring the desktop up. Chkdsk reports nothing and the raid check says that everything is fine. I'm thinking hardware failure, probably HDD but wanted some other opinions. I'm planning to try a linux live cd to see if it works without using the hard disks. If anyone has any input, it would be greatly appreciated. Delenda

  Read the article

• Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

  - by William

  I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

  Read the article

• Why is this iptables rule that does port forwarding not working?

  - by videoguy

  I have a server bound to localhost:7060. It is using ipv6 socket instead of ipv4. Below is netstat outout. # netstat -an Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 10.200.32.98:1720 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4122 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4123 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:4123 127.0.0.1:43051 ESTABLISHED tcp 0 0 10.200.32.98:5555 10.200.32.44:53162 ESTABLISHED tcp6 0 0 :::5060 :::* LISTEN tcp6 0 0 ::ffff:127.0.0.1:7060 :::* LISTEN tcp6 0 0 :::23 :::* LISTEN tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.142:43505 ESTABLISHED tcp6 0 0 ::ffff:127.0.0.1:43051 ::ffff:127.0.0.1:4123 ESTABLISHED tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.44:53195 ESTABLISHED udp6 0 0 :::5060 :::* CLOSE # I want to setup a port forwarding rule that accepts connections on port 24 (on all interfaces loopback as well as eth0) and forward the data to localhost:7060. This is how I am setting up the iptables rule: iptables -t nat -A PREROUTING -p tcp --dport 24 -j DNAT --to 127.0.0.1:7060** It is not working. When I telnet from different box, I see the following $telnet 10.200.32.98 24 Trying 10.200.32.98... If I change the server to bind to *:7060 and set the following rule, it seems to work fine. iptables -t nat -A PREROUTING -p tcp --dport 24 -j REDIRECT --to-port 7060 But that will make my server available on WAN interface which I don't like. I feel it had something to do with ipv6 socket (tcp6 line in netstat output). This whole thing is done on an Android device with custom built Android platform image. How do I get this working?

  Read the article

• ubuntu's average load never below "0.00 0.01 0.05"

  - by Karma Fusebox

  I have several ubuntu 12.04 VMs running on a ubuntu 12.04 KVM host. Those of the virtual machines that are totally idle with no services (except syslog and the other "small" standard stuff of a fresh installation) show a constant load of "0.00 0.01 0.05" in top/htop as average 1/5/15. When there are "real" applications running, the load averages behave perfectly normal but they never fall below the mentioned values. While this doesn't affect performance at all and could easily be ignored, it screws up the monitoring graphs in a very annoying way: (Notice how load15 behaves nicely if 0.05 for a short time in the right half of the pic) Unfortunately I don't know what diagnostic outputs might be helpful for you, so here's some default stuff: # top top - 16:31:01 up 1:05, 1 user, load average: 0.00, 0.01, 0.05 Tasks: 62 total, 1 running, 61 sleeping, 0 stopped, 0 zombie Cpu(s): 0.2%us, 0.2%sy, 0.0%ni, 99.2%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1019464k total, 73452k used, 946012k free, 6140k buffers Swap: 0k total, 0k used, 0k free, 22504k cached . # free -m total used free shared buffers cached Mem: 995 72 923 0 6 21 -/+ buffers/cache: 43 951 Swap: 0 0 0 . # iostat -x /dev/vda Linux 3.2.0-32-virtual (vm3) 11/15/2012 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 0.25 0.00 0.65 0.20 0.24 98.66 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util vda 0.14 0.12 0.51 0.22 6.74 1.46 22.50 0.02 23.26 20.64 29.30 7.63 0.56 Need something else? Has anyone ever seen this behavior? Might this be a bug in kvm/ubuntu/kernel 3.x in the end? Thanks a lot!

  Read the article

• Linux RAID: Replacing Failed Drive...permanantly

  - by user137519

  Okay, odd question here. I have a server with RAID 5. A drive failed, in a really physically in a really odd way. On the machine it boots and is seen by the BIOS but...no partition can be seen on the drive consistantly (in and out). 2 out of 3 drives working...I made new spare disk and added it, RAID 5 rebuilt clean. All appears well but...when I reboot it keeps trying to use the 2nd drive which doesn't give any partition data, so of course the RAID 5 gets 2 out of 3...again. The status of my drive is as follows: /dev/sda2:Good /dev/sdb2 (drive has physical problem so no partition data) bad, /dev/sdc2:good /dev/sdd2:good. Every time I reboot the mdadm system seems to keep trying to use /dev/sdb which has physical failure (although spins and is detected). /dev/sdd is the new drive I created. I added /dev/sdd to the raid and it rebuilds the raid but this action isn't memorized upon reboot so it keeps listing /dev/sda and /dev/sdc but doesn't use the perfectly good /dev/sdd until I re-add manually. I've tried removing the dead drive with the mdadm tool, but as it cannot see /dev/sdb paritions it will not fail or remove it (says partition doesn't exist). the /etc/mdadm.conf was automatically made on the original OS install which only lists: DEVICE partitions MAILADDR root ARRAY /dev/md2 super-minor=2 ARRAY /dev/md0 super-minor=0 ARRAY /dev/md1 super-minor=1 Basically just the raids to use on boot. I need to remove this semi-dead drive (/dev/sdb) but I'd prefer to know why this is happening before I do. any ideas or suggestions. I supposed I could attempt to clone/replace /dev/sdb (the partitions on drive show up, then disappear shortly after) but given the partition "chester cat" behaviour this seems risky to me and as I have a working "spare" it seems unnecessary. Thanks in advance for your insight.

  Read the article

• ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

  - by Stan

  I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

  Read the article

• NAT via iptables and virtual interface

  - by Alex

  I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Can you see something wrong in my .htaccess?

  - by AlexV

  OK, after many search, trial and errors I've managed to create an .htaccess that do what I wanted (see explanations and questions after the code block): <IfModule mod_rewrite.c> RewriteEngine On #1 If the requested file is not url-mapper.php (to avoid .htaccess loop) RewriteCond %{REQUEST_FILENAME} (?<!url-mapper\.php)$ #2 If the requested URI does not end with an extension OR if the URI ends with .php* RewriteCond %{REQUEST_URI} !\.(.*) [OR] RewriteCond %{REQUEST_URI} \.php.*$ [NC] #3 If the requested URI is not in an excluded location RewriteCond %{REQUEST_URI} !^/seo-urls\/(excluded1|excluded2)(/.*)?$ #Then serve the URI via the mapper RewriteRule .* /seo-urls/url-mapper.php?uri=%{REQUEST_URI} [L,QSA] </IfModule> This is what the .htaccess should do: #1 is checking that the file requested is not url-mapper.php (to avoid infinite redirect loops). This file will always be at the root of the domain. #2 the .htaccess must only catch URLs that don't end with an extension (www.foo.com -- catch | www.foo.com/catch-me -- catch | www.foo.com/dont-catch.me -- don't catch) and URLs ending with .php* files (.php, .php4, .php5, .php123...). #3 some directories (and childs) can be excluded from the .htaccess (in this case /seo-urls/excluded1 and /seo-urls/excluded2). Finally the .htaccess feed the mapper with an hidden GET parameter named uri containing the requested uri. Even if I tested and everything works, I want to know if what I do is correct (and if it's the "best" way to do it). I've learned a lot with this "project" but I still consider myself a beginner at .htaccess and regular expressions so I want to triple check it there before putting it in production...

  Read the article

< Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >