Search Results

Search found 18728 results on 750 pages for 'setup deployment'.

Page 600/750 | < Previous Page | 596 597 598 599 600 601 602 603 604 605 606 607  | Next Page >

• L2TP over IPSec VPN with OpenSwan and XL2TPD can't connect, timeout on Centos 6

  - by Disco

  I'm setting up LT2p over IPSec on my Centos 6.3 fresh install. I have iptables flushed, permit all. Whenever I try to connect, i get a 'no reply from vpn' and nothi Here's my ipsec.conf file (Server is 1.2.3.4) : config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=1.2.3.4 leftprotoport=17/1701 right=%any rightprotoport=17/%any My /etc/ipsec.secrets 1.2.3.4 %any: PSK "password" My sysctl.conf (appened lines) net.ipv4.ip_forward = 1 net.ipv4.conf.default.rp_filter = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.default.send_redirects = 0 net.ipv4.conf.all.log_martians = 0 net.ipv4.conf.default.log_martians = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.conf.default.accept_redirects = 0 net.ipv4.icmp_ignore_bogus_error_responses = 1 Here's what 'ipsec verify' gives: # ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.32/K2.6.32-279.19.1.el6.x86_64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] And I see xl2tpd is listening on 1701/udp : udp 0 0 1.2.3.4:1701 0.0.0.0:* 2096/xl2tpd

  Read the article

• Prevent master to fall back to master after failure

  - by Chrille

  I'm using keepalived to setup a virtual ip that points to a master server. When a failover happens it should point the virtual ip to the backup, and the IP should stay there until I manually enable (fix) the master. The reason this is important is that I'm running mysql replication on the servers and writes should only be on the master. When I failover I promote the slave to master. The master server: global_defs { ! this is who emails will go to on alerts notification_email { [email protected] ! add a few more email addresses here if you would like } notification_email_from [email protected] ! I use the local machine to relay mail smtp_server 127.0.0.1 smtp_connect_timeout 30 ! each load balancer should have a different ID ! this will be used in SMTP alerts, so you should make ! each router easily identifiable lvs_id APP1 } vrrp_instance APP1 { interface eth0 state EQUAL virtual_router_id 61 priority 999 nopreempt virtual_ipaddress { 217.x.x.129 } smtp_alert } Backup server: global_defs { ! this is who emails will go to on alerts notification_email { [email protected] ! add a few more email addresses here if you would like } notification_email_from [email protected] ! I use the local machine to relay mail smtp_server 127.0.0.1 smtp_connect_timeout 30 ! each load balancer should have a different ID ! this will be used in SMTP alerts, so you should make ! each router easily identifiable lvs_id APP2 } vrrp_instance APP2 { interface eth0 state EQUAL virtual_router_id 61 priority 100 virtual_ipaddress { 217.xx.xx.129 } notify_master "/etc/keepalived/notify.sh del app2" notify_backup "/etc/keepalived/notify.sh add app2" notify_fault "/etc/keepalived/notify.sh add app2” smtp_alert }

  Read the article

• Strange behaviour when creating/deleting subdomains

  - by Saif Bechan

  This can be a DNS cache issue from my local machine, but I am not sure. This is what happens. I have a domain that does not use wildcard subdomains, so they have to be created. Without creating the domain, and I point my browser to test.domain.com, I get a page server not found. Now when I create the subdomain, I keep getting the same problem. Now when I first create the domain, without ever visiting the page, I get the normal page, but now when I delete the subdomain, it never goes away. Can this be a DNS cache issue, I am working on a shared environment, maybe the router has a cache but I doubt that. Can this have something to do with my setup. I have tried to use the Google DNS hosting, but this gives me the same results. I have also tried some tools that clear my local DNS cache, they were some add-ons for FireFox. Anyone have any ideas what can be the problem. Are there any tests I can do to see if there is some kind of cache between me and the server.

  Read the article

• Windows 7 XP Mode-Program not ending properly

  - by iceman33

  We currently have recently have implemented a few new machines to our network with Windows 7 Enterprise 64-bit installed on them. We have a program that is incompatible with Windows 7 right now and we have it installed on the Windows XP Mode that we have setup on there. There is a shortcut that is on the desktop to have it work with integration services and that part is working successfully. Occasionally, this program will stop working over the server on which it connects to has to get rebooted and the program has to get closed out. However, that process that is in the task manager doesn't seem to close out properly. So in order to correctly get the program shut down, we have to make the users log back into xp mode and do a Ctrl+Alt+Delete to kill the process or have to go back into the machine to perform a restart. I was wondering if anyone has come across a way within XP Mode yet that when the virtual machine goes into hibernation mode that it would shut down all processes or if when restarting the virtual machine your normal machine that it would shut everything down in the virtual XP mode as well and not just keep that program running? Any help would be greatly appreciated.

  Read the article

• Configuring CakePHP on Hostgator

  - by yaeger

  I have absolutely no idea what I am doing wrong here. I have followed just about every guide there is with installing cakephp on shared hosting and I am still having problems. I have also started over each time when following a guide. Maybe someone can help me out here as I am out of options. Here is my current setup: / app webroot vendors lib cake public_html .htaccess index.php plugins I have configured the index.php file in the public_html to point to the correct files. I have also done this in the index.php file located in webroot folder. I am getting an Internal 500 server error and it says to check my logs for what the error specifically is. However there are no logs being generated. I removed the .htaccess file from the public_html folder and I get the following errors: Warning: require(/app/webroot/index.php) [function.require]: failed to open stream: No such file or directory in /home/user/public_html/index.php on line 40 Fatal error: require() [function.require]: Failed opening required '/app/webroot/index.php' (include_path='.:/usr/lib/php:/usr/local/lib/php') in /home/user/public_html/index.php on line 40 line 40 is require APP_DIR . DS . WEBROOT_DIR . DS . 'index.php'; DS = "/" WEBROOT_DIR = "app" Anyone have any suggestions? I am at lost at what I am doing wrong.

  Read the article

• Hyper-V VM Lab + RRAS + RDP

  - by Dennis Evans

  My background is primarily .NET Development with some System Administration skills. I'm trying to set up a VM Lab for me to test System Applications I'm developing but I've only ever done System Administration in already set up environments; I've never set up my own. My current setup: Server 2008 R2 Hyper-V Host on physical machine (only role enabled) with two NICs. First NIC dedicated for Management w/ DHCP address from company's network. Second NIC dedicated to RRAS VM w/ DHCP address from company's network. RRAS VM has two NICS, one is virtual private internal only NIC w/ static entry. The other is the physical NIC mentioned above. I've joined it to my VMLab.net internal domain. My Active Directory Domain Controller server (ADCT) also runs DNS, DHCP, and Certificate Services which I'm familiar with but don't understand completely. RRAS is already set up with NAT to provide the private internal network with Internet access. What I would like to do is be able to RDP into the servers/computers on the VMLab.net domain from my computer. Do I need to add the Remote Desktop Services role and enable the Remote Desktop Gateway service on RRAS in order to do this or is there a way to set up port forwarding on RRAS to just allow a direct connection to the internal servers...or both? What would the best practices be here? Network Diagram http://i.stack.imgur.com/4qfnk.png

  Read the article

• Cannot access server shares over VPN

  - by DuncanDavies

  I've set up a single hosted server to use as a development environment for a web-based application. The web app is served up fine on port 80, however I'm struggling to get my VPN to behave how I'd expect so the developers don't have the access they require. The VPN connects fine and I can access the back-end database (SQL Server) which resides on the server with the client tools from the laptops. However they cannot access any shared folders. The server's local IP address is 10.x.x.x, and I've assigned a static IP address pool to RRAS (of 192.168.100.1 - 20). The clients pick up a valid IP Address (i.e. 192.168.100.9) when they connect. There is no name resolution setup, DNS or WINS. When connected via VPN the clients can ping the server (192.168.100.1) by IP Address, but cannot map a drive to a shared folder (net use * \\192.168.100.1\xxxxx) - I get 'System error 53 has occurred. The network path was not found.' I don't understand why I can ping by the ip, but not map by it. Some details: Server OS is Windows 2008 (Datacenter) VPN is SSTP using RRAS Clients are all Windows 7 I've tried temporarily disabling the firewalls So, why can we not access the file system when everything else (ping, RDP, SQL Server clients tools) works? Thanks for your help Duncan

  Read the article

• Using proxy.pac to access Apache 2 with a hostname?

  - by leeand00

  Note that I do not have a DNS on my network, and that is why I am resorting to using a proxy.pac file. I would like to be able to access my development Apache 2 server using a name instead of an ip without setting up a full blown DNS. I am aware of setting names in the C:\Windows\System32\drivers\etc\hosts file and the /etc/hosts files, however I cannot edit the hosts file on all of the devices that I am testing the site on. I've added a proxy.pac file to my Apache2 server and pointed my browsers settings to it at: http://192.168.2.221/proxyutils/proxy.pac ...where 192.168.2.221 is thehostname's ip address. I set the above URL in Firefox in the following manner: From the menubar selecting "Edit-Preferences" In the resulting "Firefox Preferences" window clicking the "Advanced" tab. Clicking the "Network" tab Clicking the "Settings" button. Selecting the "Automatic proxy configuration URL:" radio button. Entering http://192.168.2.221/proxyutils/proxy.pac and pressing OK. The contents of the proxy.pac file on the Apache server function FindProxyForURL(url, host) { if( dnsDomainIs(host, "thehostname") ) return "PROXY 192.168.2.221:80"; return "DIRECT"; } In Firefox I then access the following URL: http://thehostname/wp-blog/ And instead of the development version of the Wordpress blog I am trying to access I get a URL of http://thehostnamehttp/thehostname/wp-blog/ in my address bar and a 404 Not Found page in the browser window. Looking over proxy.pac, it seems like calling dnsDomainIs shouldn't work considering I don't have a DNS setup on my network, but I've also tried just comparing the host argument with the string "hostname" and it yielded the same result, even after modifying the proxy.pac file and clicking the reload button near the proxy settings. This could also be a Wordpress problem, since I've noticed that directories without Wordpress seem to function perfectly normally. (see cross post here) Is there any way I can modify my configuration so that I can access the site using http://thehostname/wp-blog/ ?

  Read the article

• Offline cache copies in Windows file sharing

  - by netvope

  I frequently access media files (music or video) on a remote Windows file share. My Internet connection is not very fast, and I find it a waste of bandwidth when I repeatedly access the same files. For example, I may listen to the same song 30 times in a month. So, I would like to cache files I've used. I know Windows has an "Always available offline" feature but I dont' think it suit my needs. I don't want to make the whole share "available offline" as the remote Windows file share is huge (in terabytes). Making individual files "available offline" is tedious as the files are scattered in many different directories. It would be much more convenient if the system can simply cache those I've used. I could also manually make a local copy each time I use a file... but this is even more troublesome than making each file "available offline" Also The files on the share seldom change. Many of the files are rarely used. Some of the files are frequently used. I don't have a list of the most frequently used files. It would be the best if I could tell Windows to cache the last accessed 10GB, but apparently it doesn't have this feature. So I think the best way is to have a SMB/CIFS caching proxy. What do you think? I have a Linux box sitting around. Perhaps I should try to setup samba4?

  Read the article

• Using gitlab behind Apache proxy all generated urls are wrong

  - by Hippyjim

  I've set up Gitlab on Ubuntu 12.04 using the default package from https://about.gitlab.com/downloads/ {edit to clarify} I've set up Apache to proxy and run the nginx server the package installed on port 8888 (or so I thought). As I had Apache installed already I have to run nginx on localhost:8888. The problem is, all images (such as avatars) are now served from http://localhost:8888, and all the checkout urls Gitlab gives are also localhost - instead of using my domain name. If I change /etc/gitlab/gitlab.rb to use that url, then Gitlab stops working and gives a 503. Any ideas how I can tell Gitlab what URL to present to the world, even though it's really running on localhost? /etc/gitlab/gitlab.rb looks like: # Change the external_url to the address your users will type in their browser external_url 'http://my.local.domain' redis['port'] = 6379 postgresql['port'] = 2345 unicorn['port'] = 3456 and /opt/gitlab/embedded/conf/nginx.conf looks like: server { listen localhost:8888; server_name my.local.domain; [Update] It looks like nginx is still listening on the wrong port if I don't specify localhost:8888 as the external_url. I found this in /var/log/gitlab/nginx/error.log 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: still could not bind() Apache setup looks like: <VirtualHost *:80> ServerName my.local.domain ServerSignature Off ProxyPreserveHost On AllowEncodedSlashes NoDecode <Location /> ProxyPass http://localhost:8888/ ProxyPassReverse http://127.0.0.1:8888 ProxyPassReverse http://my.local.domain </Location> </VirtualHost> Which seems to proxy everything back ok if Gitlab listens on localhost:8888 - I just need Gitlab to start displaying the right URL, instead of localhost:8888.

  Read the article

• Microsoft Application Request Routing with Windows Authentication

  - by theplatz

  I'm running into a problem trying to get Windows Authentication working in an environment that uses Microsoft Application Request Routing and was hoping someone might be able to help. The problem I'm running into is that only some requests are authenticated, while others fail with 401 errors. I have followed the Special Case of Running IIS 7.0 in a Web Farm instructions found at http://blogs.msdn.com/b/webtopics/archive/2009/01/19/service-principal-name-spn-checklist-for-kerberos-authentication-with-iis-7-0.aspx to no avail. My current server setup looks like the following: ARR Two servers set up with IIS shared configuration using IIS 7.5 on Windows 2008 R2 Anonymous authentication turned on for the Default Web Site Web Farm Two servers running IIS 7.5 on Windows 2008 R2 Three web sites set up using port binding to differentiate between virtual hosts. Ports being used are 8000, 8001, and 8002 Application pools for Windows Authentication all use a common domain account SPN added to domain account for http/<virthalhost-name>:<port-number> and http/<virtualhost-name>.<fully-qualified-domain>:<port-number> The IIS logs show the following when authentication is working/failing. If I understand correctly, all requests should show DOMAIN\User_Name: 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/stylesheets/techweb.landing.css - 8002 DOMAIN\User_Name ARR-HOST-1-IP-ADDRESS 200 0 0 62 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-background-right.gif - 8002 - ARR-HOST-1-IP-ADDRESS 401 2 5 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-background-left.gif - 8002 DOMAIN\User_Name ARR-HOST-IP-ADDRESS 200 0 0 31 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-icon.png - 8002 - ARR-HOST-1-IP-ADDRESS 401 2 5 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-icon.png - 8002 - ARR-HOST-1-IP-ADDRESS 401 1 2148074248 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/application-icon.png - 8002 - ARR-HOST-1-IP-ADDRESS 401 1 2148074248 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-background-right.gif - 8002 - ARR-HOST-1-IP-ADDRESS 401 1 3221225581 15 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/building.gif - 8002 DOMAIN\User_Name ARR-HOST-2-IP-ADDRESS 200 0 0 218 Does anyone know what might cause this problem and how I can resolve it?

  Read the article

• How can I disable DNSSC for Google Apps (GMail) MX records on my authoritative domains?

  - by meinemitternacht

  I'm running a BIND Master / Slave setup with DNSSEC, but some of my domains use Google Apps for e-mail services. Google doesn't support DNSSEC and BIND doesn't like it at all. Log output: Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM.dlv.isc.org/DLV/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/A/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/AAAA/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755cb83950: ALT2.ASPMX.L.GOOGLE.COM AAAA: bad cache hit (ALT2.ASPMX.L.GOOGLE.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/AAAA/IN': 69.147.224.178#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755ca52c30: ALT2.ASPMX.L.GOOGLE.COM A: bad cache hit (ALT2.ASPMX.L.GOOGLE.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/A/IN': 69.147.224.178#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755ca52c30: ASPMX2.GOOGLEMAIL.COM AAAA: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/AAAA/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755cb83950: ASPMX2.GOOGLEMAIL.COM A: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/A/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f754c1b0bd0: ASPMX2.GOOGLEMAIL.COM A: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/A/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f754c1a6a30: ASPMX2.GOOGLEMAIL.COM AAAA: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/AAAA/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755cb83950: ASPMX3.GOOGLEMAIL.COM AAAA: bad cache hit (ASPMX3.GOOGLEMAIL.COM.dlv.isc.org/DLV) I'm not absolutely sure this is stopping Google Apps from working, because I just enabled all of the DNSSEC features. Does anyone here have experience with this?

  Read the article

• Multiple static WAN IP addresses to single LAN subnet

  - by Jessy Houle

  Below is my home network topology. I currently have 5 static IP addresses, 3 of which are in use by 3 routers. These routers in-turn subnet internal networks and port forward. I use my SSL VPN appliance to remote home from work or on the road. At this point I can remotely administer my Windows Server. I know the network is setup wrong, I was matching existing hardware the best I knew how. http://storage.jessyhoule.com.s3.amazonaws.com/network_topology.jpg Ok this said, here is the problem... One of my websites on my Windows Server now needs to be secure (SSL using port 443). However, I'm already port forwarding port 443 to my VPN appliance. Furthermore, if I'm going to have to reconfigure the network, I would really like to be able to use the SSL VPN to remotely administer all machines. I mentioned this to a friend of mine, who said that what I was looking for was a firewall. Explaining that a firewall would take in multiple static (WAN) IP addresses, and still allow all internal devices to be on the same network. So, basically, I could supply my SSL VPN appliance it's very own static (WAN) IP address routing, and yet have it on the same internal network (192.168.1.x) as all my other devices. The first question is... Does this sound right? Secondly, would you suggest anything different? And, finally, what is the cheapest way to do this? I am started down the road of downloading/installing untangle and smoothwall to see if they will do the job, hoping they take multiple static (WAN) IP addresses. Thank you in advance for your answers. -Jessy Houle

  Read the article

• Postfix (delivery temporarily suspended: conversation with mydomain.net [private/lmtp] timed out while receiving the initial server greeting)

  - by Paul

  I'm running Debian 7.1, Postfix version 2.9.6, Dovecot Version 2.1.7 To set it up I followed mostly this (without the spamass-clamav-greylist bit) I have also got setup smart host relaying via gmail postconf -n reveals: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all inet_protocols = ipv4 mailbox_size_limit = 0 milter_default_action = accept mydestination = MyDomain, localhost.net, localhost myhostname = MyDomain.net mynetworks = 127.0.0.0/8 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relay_domains = mysql:/etc/postfix/mysql_relay_domains.cf relayhost = [smtp.gmail.com]:587 smtp_connect_timeout = 120s smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/relay_passwd smtp_sasl_security_options = noanonymous smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_non_fqdn_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unauth_destination, reject_unauth_pipelining, reject_invalid_hostname smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes virtual_alias_maps = mysql:/etc/postfix/mysql_virtual_alias_maps.cf virtual_gid_maps = static:3000 virtual_mailbox_base = /home/vmail virtual_mailbox_domains = mysql:/etc/postfix/mysql_virtual_mailbox_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_virtual_mailbox_maps.cf virtual_transport = lmtp:unix:private/lmtp virtual_uid_maps = static:3000 I am able to send emails to the outside world but all emails sent to me are getting stuck. mailq is showing numerous lines: A69C2414C4 2621 Fri Dec 27 14:57:03 [email protected] (conversation with MyDomain.net[private/lmtp] timed out while receiving the initial server greeting) [email protected] AB78B414BE 3796 Fri Dec 27 14:56:50 [email protected] (delivery temporarily suspended: conversation with MyDomain.net[private/lmtp] timed out while receiving the initial server greeting) [email protected] /var/log/mail.log is showing: Dec 28 09:50:09 hostname postfix/lmtp[10828]: E947C414CD: to=, relay=localhost[private/lmtp], delay=64012, delays=63712/0.25/300/0, dsn=4.4.2, status=deferred (conversation with localhost[private/lmtp] timed out while receiving the initial server greeting) Any help would be greatly appreciated. Thank you

  Read the article

• slicehost google apps mx settings

  - by Bob

  Hello All, I am banging my head against the wall on this one. I followed the MX setup tutorials for Google Mail and it didn't work. Currently, after deleting those records and adding the ones google suggested I have domain.com. 86400 IN MX 10 ASPMX.L.GOOGLE.com. domain.com. 86400 IN MX 20 ALT2.ASPMX.L.GOOGLE.com. domain.com. 86400 IN MX 20 ALT1.ASPMX.L.GOOGLE.com. domain.com. 86400 IN MX 30 ASPMX2.GOOGLEMAIL.com. domain.com. 86400 IN MX 30 ASPMX5.GOOGLEMAIL.com. domain.com. 86400 IN MX 30 ASPMX3.GOOGLEMAIL.com. domain.com. 86400 IN MX 30 ASPMX4.GOOGLEMAIL.com. according to the output of my dig command for my particular "domain". I can send email from google apps mail but I can not recieve any email. It gives me the following error: Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 #5.1.0 Address rejected [email protected] Now I already tried following the slicehost MX article instructions straight as well and they did not work out for me. The domain has already been verified by google and it says the email is activated from their end. Any help would be appreciated : )

  Read the article

• Getting 401 when using client certificate with IIS 7.5

  - by Jacob

  I'm trying to configure a web site hosted under IIS 7.5 so that requests to a specific location require client certificate authentication. With my current setup, I still get a "401 - Unauthorized: Access is denied due to invalid credentials" when accessing the location with my client cert. Here's the web.config fragment that sets things up: <location path="MyWebService.asmx"> <system.webServer> <security> <access sslFlags="Ssl, SslNegotiateCert"/> <authentication> <windowsAuthentication enabled="false"/> <anonymousAuthentication enabled="false"/> <digestAuthentication enabled="false"/> <basicAuthentication enabled="false"/> <iisClientCertificateMappingAuthentication enabled="true" oneToOneCertificateMappingsEnabled="true"> <oneToOneMappings> <add enabled="true" certificate="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"/> </oneToOneMappings> </iisClientCertificateMappingAuthentication> </authentication> </security> </system.webServer> </location> The client certificate I'm using in my web browser matches what I've placed in the web.config. What am I doing wrong here?

  Read the article

• Redis as substitution for Memcache

  - by Boban P.

  We have distributed web app, and for now, as session handler, we use two separate instances of memcache in redundancy, so everything that is written in one memcache is also written in other. Memcache is fairly easy to install, use, and maintain but we have one problem: if one memcache fail, everything is fine, php comunicate with other instance which has all data (although, half of connections have a delay because they try to use failed one, wait a little, and then contact other memcache). When failed instance comes back to life again, it starts up empty. If established session request data from that instance, session fails, and user logs out, and that happens to half of users.So, we are thinking about to switch to redis for session handling, and maybe keep memcache for cache only. My questions are: If we setup redis instances as master-slave, and if master fails, can sentinel promote slave as new master and when old master comes back to life, will it stay as slave or not? Is redis call malloc at startup to allocate part of memory, like memcache or varnish, or it calls malloc for every key inserted? And what are pros and cons of that?

  Read the article

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• Mongrel Cluster on Ubuntu Server Karmic

  - by trobrock

  I am trying to get mongrel cluster working on my Ubuntu Server Karmic box in preparation to setup Capistrano. I've been trying to get the two to work all day and finally decided to completely remove Capistrano and see if I can just get Mongrel Cluster to work. I ran this to install mongrel cluster: gem install mongrel mongrel_cluster Everything installed fine, when I change into my app's directory... # mongrel_rails -bash: mongrel_rails: command not found I can run it from its install location: # /var/lib/gems/1.8/bin/mongrel_rails Usage: mongrel_rails <command> [options] Available commands are: ... It lets me build the cluster configuration file fine, but when I run the clister:start command: # /var/lib/gems/1.8/bin/mongrel_rails cluster::start starting port 8000 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8000 -P tmp/pids/mongrel.8000.pid -l log/mongrel.8000.log starting port 8001 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8001 -P tmp/pids/mongrel.8001.pid -l log/mongrel.8001.log starting port 8002 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8002 -P tmp/pids/mongrel.8002.pid -l log/mongrel.8002.log It seems it isnt calling it from the right directory after that command, what can I do to fix this? I tried setting the path previously when trying to set up Capistrano, but the path didnt stay set when Capistrano used ssh to run the commands.

  Read the article

• JBossMQ - Clustered Queues/NameNotFoundException: QueueConnectionFactory error

  - by mfarver

  I am trying to get an application working on a JBoss Cluster. It uses Queues internally, and the developer claims that it should work correctly in a clustered environment. I have jbossmq setup as a ha-singleton on the cluster. The application works correctly on whichever node currently is running the queue, but fails on the other nodes with a: "javax.naming.NameNotFoundException: QueueConnectionFactory not bound" error. I can look at JNDIview from the jmx-console and see that indeed the QueueConnectionFactory class only appears on the primary node in the Global context. Is there a way to see the Cluster's JNDI listing instead of each server? The steps I took from a default Jboss 4.2.3.GA installation were to use the "all" configuration. Then removed /server/all/deploy/hsqldb-ds.xml and /deploy-hasingleton/jms/hsqldb-jdbc2-service.xml, copying the example/jms/mysq-jdbc2-service.xml file into its place (editing that file to use DefaultDS instead of MySqlDS). Finally I created a mysql-ds.xml file in the deploy directory pointing "DefaultDS" at an empty database. I created a -services.xml file in the deploy directory with the queue definition. like the one below: <server> <mbean code="org.jboss.mq.server.jmx.Queue" name="jboss.mq.destination:service=Queue,name=myfirstqueue"> <depends optional-attribute-name="DestinationManager"> jboss.mq:service=DestinationManager </depends> </mbean> </server> All of the other cluster features of working, the servers list each other in the view, and sessions are replicating back and forth. The JBoss documentation is somewhat light in this area, is there another setting I might have missed? Or is this likely to be a code issue (is there different code to do a JNDI lookup in a clusted environment?) Thanks

  Read the article

• How do I migrate Exchange 2007 to new hardware?

  - by Graeme Donaldson

  As per my previous question, I have an Exchange 2007 box which is also a DC. Since I can't demote it while Exchange is installed, I want to move Exchange to a different server. Does anyone have any articles, tips or experiences to share on this? The last time I did this it was with Exchange 2003 and even that is a little rusty in my head. The setup is a single Exchange 2007 Hub/Edge/Mailbox/CAS server. Its currently on Windows Server 2008, I can migrate it to the same OS, or I can go to 2008 R2, I'm not really picky on that. We're running OWA/ActiveSync/POP3(S)/IMAP(S) for client access. I already have another fully functional DC/GC/DNS box in the same site and clients in the site are already using that for DNS. It's also the preferred site bridgehead for AD replication. Update: After reading Evan's answer I realised that my original question wasn't worded correctly. I'm not looking to do a swing migration, I actually need to move Exchange completely over to a new box. I have done swing migrations in the past, i.e. moving over to a temporary box and back to the original hardware afterwards, and I'm not really sure why I used that term in the original question since it's not what I intended. Any tips?

  Read the article

• Triple-monitor set-up (2 unique, 1 cloned): Can a VGA splitter be used on one output of a dual-head

  - by stakx

  Background: I'm currently researching hardware components for some kind of information terminal we're building. This application of ours makes use of three output screens: (1) A touch screen where all user input is made; (2) A regular LCD monitor where the requested information is being displayed; and (3) A projector which displays exactly the same signal as screen (2) does. (All screens will run at the same resolution of 1024x768 btw.) Now I figured that using a dual-head video card would be sufficient, let's say a Matrox P690 low-profile PCI card. This would involve having a Y cable connected to the graphics card itself, then two DVI-to-VGA adapters at each end of the Y cable, and then having a VGA splitter on one of the VGA outputs. The following shows the setup in question: 0--1---------2-> VGA (DSUB-15) \ \ ----2-3---------> VGA (DSUB-15) \ \ -----------------> VGA (DSUB-15) 0: graphics card (LFH60 jack) 1: LFH60 to DVI-I dual monitor Y cable 2: DVI-to-VGA adapters 3: VGA splitter cable Question(s): Will this work? I'm particularly concerned about the following points: Can a low-profile PCI video card output a signal which is strong enough for three monitors (even if it's a dual-head card)? Does the combination of so many adapters and splitter cables work? (The LFH-to-DVI cable comes with the video card) Will the VGA splitter cable degrade the signal on the output screen & projector significantly? (If so, would a USB-powered splitter cable remedy this problem?) I can't possibly expect anyone to answer all those questions, but any input is appreciated.

  Read the article

• Optimizing Disk I/O & RAID on Windows SQL Server 2005

  - by David

  I've been monitoring our SQL server for a while, and have noticed that I/O hits 100% every so often using Task Manager and Perfmon. I have normally been able to correlate this spike with SUSPENDED processes in SQL Server Management when I execute "exec sp_who2". The RAID controller is controlled by LSI MegaRAID Storage Manager. We have the following setup: System Drive (Windows) on RAID 1 with two 280GB drives SQL is on a RAID 10 (2 mirroed drives of 280GB in two different spans) This is a database that is hammered during the day, but is pretty inactive at night. The DB size is currently about 13GB, and is used by approximately 200 (and growing) users a day. I have a couple of ideas I'm toying around with: Checking for Indexes & reindexing some tables Adding an additional RAID 1 (with 2 new, smaller, HDs) and moving the SQL's Log Data File (LDF) onto the new RAID. For #2, my question is this: Would we really be increasing disk performance (IO) by moving data off of the RAID 10 onto a RAID 1? RAID 10 obviously has better performance than RAID 1. Furthermore, SQL must write to the transaction logs before writing to the database. But on the flip side, we'll be reducing both the size of the disks as well as the amount of data written to the RAID 10, which is where all of the "meat" is - thereby increasing that RAID's performance for read requests. Is there any way to find out what our current limiting factor is? (The drives vs. the RAID Controller)? If the limiting factor is the drives, then maybe adding the additional RAID 1 makes sense. But if the limiting factor is the Controller itself, then I think we're approaching this thing wrong. Finally, are we just wasting our time? Should we instead be focusing our efforts towards #1 (reindexing tables, reducing network latency where possible, etc...)?

  Read the article

• What are the biggest, best CPUs that support Physical Address Extension?

  - by Giffyguy

  I'm looking for a CPU that will support PAE and fit into an LGA775 socket. This combination of technology is very much preferred for my current server hardware/software setup. My priorities in order of highest to lowest: PAE & LGA775 At least 1066Mhz FSB Largest CPU cache possible Multiple Cores if possible HyperThreading if possible Most other factors are of little-to-no consequence. I'm finding it very difficult to figure out what my options are. Intel doesn't have much useful information on PAE (since x64 is so dominant), and Wikipedia simply says that "PAE is provided by Intel Pentium Pro (and above) CPUs - including all later Pentium-series processors except the 400 MHz bus versions of the Pentium M." All of Intel's listed Pentium CPU's support Intel64, which makes me seriously doubt they will support PAE with a 32-bit OS. And Wikipedia's claim is so vague, I have no idea if they mean up-to-and-including the x64 Prescott CPUs. PAE is supposed to be an aspect of the x86 architecture, and I believe it is no longer supported in an x64 environment. Please correct me if I am wrong.

  Read the article

• My Boot order changed. Why?

  - by Chris

  I have a laptop running Windows XP SP3 with one internal hard drive partitioned into C: (system), D: (storage) and I have an external hard drive, F: (external drive). Yesterday the machine was running fine. Today, I go back to it and see that it's just showing a blinking cursor. Checked through the BIOS and the hard drive checked out fine. CTRL-ALT-DELETED the machine a few times, but I was never able to boot back into the operating system. I threw in a live CD and found out that the boot order of the drives has changed. The external drive is now C:, the system partiton is D:, and the storage partition is E:. Does anyone have any idea of how or why this would have occured? Auto system updates are turned off so there should have been no automatic reboot of the system overnight, and anti-virius runs on the machine and has found no infections before this occured. Edit When I was looking through the BIOS of the machine, I did see that the boot order was changed. But still the same question remains, what would have caused this to happen? I can't believe that a random reboot happened and totally changed my hard drive setup.

  Read the article

< Previous Page | 596 597 598 599 600 601 602 603 604 605 606 607  | Next Page >