Search Results

Search found 38064 results on 1523 pages for 'oracle linux'.

Page 610/1523 | < Previous Page | 606 607 608 609 610 611 612 613 614 615 616 617  | Next Page >

  • Rate limit a wireless interface

    - by Jamie Hankins
    I have access to my routers SSH and IPTables. I want to rate limit my guest network to 1Mb/s so they can't guzzle my bandwidth. rai1 RTWIFI SoftAP ESSID:"GuestNetwork" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi0 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F8 Bit Rate=300 Mb/s wdsi1 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi2 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s wdsi3 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s I'm just wondering the command I need to limit it. I tried the iwconfig limit command but it failed. Thanks

    Read the article

  • can't figure out why apache LDAP auth fails

    - by SethG
    Suddenly, yesterday, one of my apache servers became unable to connect to my LDAP (AD) server. I have two sites running on that server, both of which use LDAP to auth against my AD server when a user logs in to either site. It had been working fine two days ago. For reasons unknown, as of yesterday, it stopped working. The error log only says this: auth_ldap authenticate: user foo authentication failed; URI /FrontPage [LDAP: ldap_simple_bind_s() failed][Can't contact LDAP server], referer: http://mysite.com/ I thought perhaps my self-signed SSL cert had expired, so I created a new one for mysite.com, but not for the server hostname itself, and the problem persisted. I enabled debug-level logging. It shows the full SSL transaction with the LDAP server, and it appears to complete without errors until the very end when I get the "Can't contact LDAP server" message. I can run ldapsearch from the commandline on this server, and I can login to it, which also uses LDAP, so I know that the server can connect to and query the LDAP/AD server. It is only apache that cannot connect. Googling for an answer has turned up nothing, so I'm asking here. Can anybody provide insight to this problem? Here's the LDAP section from the apache config: <Directory "/web/wiki/"> Order allow,deny Allow from all AuthType Basic AuthName "Login" AuthBasicProvider ldap AuthzLDAPAuthoritative off #AuthBasicAuthoritative off AuthLDAPUrl ldaps://domain.server.ip/dc=full,dc=context,dc=server,dc=name?sAMAccountName?sub AuthLDAPBindDN cn=ldapbinduser,cn=Users,dc=full,dc=context,dc=server,dc=name AuthLDAPBindPassword password require valid-user </Directory>

    Read the article

  • How to prevent Ubuntu from combining networks on 2 NIC server?

    - by SolarPower
    I've got a Ubuntu Server 10.10 with 2 network interfaces with a cable plugged into both going to switches on completely different networks with different routers. One network is the 10.1.10.X network with a separate gateway/router - the server has an IP of 10.1.10.50 with the gateway IP of 10.1.10.1. The other interface is 10.2.10.X, IP 10.2.10.50, gateway 10.2.10.1. All my Mac machines are on the 10.2.10.X network, and all servers on the 10.1.10.X. The ONLY connection between the two is this machine. From a Mac in my office, I CANNOT ping any computer on the 10.1.10.X network except the Ubuntu machine I'm talking about. However, under the Shared column in Finder, I can see every server on the other network listed. That makes me believe that somehow this Ubuntu machine is letting certain requests span both networks, which is a security problem. Hope this is enough info.

    Read the article

  • How to copy remote machines text to local machines clipboard through SSH?

    - by recluze
    I work on a remote machine through ssh. I have a very large text file there (approx. 500 lines) which I usually need to modify, then copy the contents of that file and paste it in my local browser. The way I usually do this is cat filename and then select/copy the ssh output. That takes a lot of time. I was wondering if there is a utility that will put the remote file's contents in my local clipboard.

    Read the article

  • Podcast Show Notes: William Ulrich and Neal McWhorter on Business Architecture

    - by Bob Rhubart
    The latest ArchBeat podcast program features a four-part conversation with William Ulrich and Neal McWhorter, the authors of Business Architecture: The Art and Practice of Business Transformation, available from Meghan-Kiffer Press. Listen to Part 1 Bill and Neal cover the basics and discuss the effects of the lack of business architecture on organizations. Listen to Part 2 (Jan 19) What really happens to the billions of dollars annually invested in IT. Listen to Part 3 (Jan 26) Why the IT and business sides of many organizations can’t play nice. Listen to Part 4 (Feb 2) How IT architects and business architects can work together to get the ship back on course and keep it there. Connect William Ulrich Website | LinkedIn | Business Architecture Guild Neal McWhorter Website | LinkedIn | Business Architecture Group on OMG Coming Soon Bob Hensle, Director, Oracle Enterprise Architecture Group, discusses the recently launched IT Solutions from Oracle (ITSO) library of documents. Excerpts from a recent OTN Architect Community Virtual Meet-up. Stay tuned: RSS del.icio.us Tags: business architecture,enterprise architecture,arch2arch,archbeat,podcast,business transformation,oracle,oracle technology network Technorati Tags: business architecture,enterprise architecture,arch2arch,archbeat,podcast,business transformation,oracle,oracle technology network

    Read the article

  • how to enable remote access to a MySQL server on an AZURE virtual machine

    - by Rees
    I have an AZURE virtual machine with a MySQL server installed on it running ubuntu 13.04. I am trying to remote connect to the MySQL server however get the simple error "Can't connect to MySQL server on {IP}" I have already done the follow: * commented out the bind-address within the /etc/mysql/my.cnf * commented out skip-external-locking within the same my.cnf * "ufw allow mysql" * "iptables -A INPUT -i eth0 -p tcp -m tcp --dport 3306 -j ACCEPT" * setup an AZURE endpoint for mysql * "sudo netstat -lpn | grep 3306" does indeed show mysql LISTENING * "GRANT ALL ON *.* TO remote@'%' IDENTIFIED BY 'password'; * "GRANT ALL ON *.* TO remote@'localhost' IDENTIFIED BY 'password'; * "/etc/init.d/mysql restart" * I can connect via SSH tunneling, but not without it * I have spun up an identical ubuntu 13.04 server on rackspace and SUCCESSFULLY connected using the same procedures outlined here. NONE of the above works on my azure server however. I thought the creation of an endpoint would work, but no luck. Any help please? Is there something I'm missing entirely?

    Read the article

  • KVM CLI install for CentOS 6.3 defaults to Minimal Install

    - by i.h4d35
    So I now I've installed KVM (and its associated tools and packages- libvirt, VMM etc.). On the GUI (i.e using the VMM), installation works as its supposed to. However, when I try to create a VM using the command line interface, the OS (I am working with CentOS 6.3) defaults to a Minimal Install instead of giving me options to choose from at the time of installation. I am trying to install using the following command: virt-install \ --connect qemu:///system \ --virt-type kvm --name testVM2 \ --ram 512 --disk path=/var/lib/libvirt/images/testVM2.img,size=8 --vnc \ --cdrom /media/db18de8e-0853-49fb-80de-5c794d58a46f/CentOS-6.3- x86_64-bin-DVD1.iso \ --network network=default Specifying the OS-type or the OS-variant parameters doesn't make a difference. Is there something that I am missing out on or some other parameter that I must specify? Thanks in advance.

    Read the article

  • Tutorial: Getting Started with the NoSQL JavaScript / Node.js API for MySQL Cluster

    - by Mat Keep
    Tutorial authored by Craig Russell and JD Duncan  The MySQL Cluster team are working on a new NoSQL JavaScript connector for MySQL. The objectives are simplicity and high performance for JavaScript users: - allows end-to-end JavaScript development, from the browser to the server and now to the world's most popular open source database - native "NoSQL" access to the storage layer without going first through SQL transformations and parsing. Node.js is a complete web platform built around JavaScript designed to deliver millions of client connections on commodity hardware. With the MySQL NoSQL Connector for JavaScript, Node.js users can easily add data access and persistence to their web, cloud, social and mobile applications. While the initial implementation is designed to plug and play with Node.js, the actual implementation doesn't depend heavily on Node, potentially enabling wider platform support in the future. Implementation The architecture and user interface of this connector are very different from other MySQL connectors in a major way: it is an asynchronous interface that follows the event model built into Node.js. To make it as easy as possible, we decided to use a domain object model to store the data. This allows for users to query data from the database and have a fully-instantiated object to work with, instead of having to deal with rows and columns of the database. The domain object model can have any user behavior that is desired, with the NoSQL connector providing the data from the database. To make it as fast as possible, we use a direct connection from the user's address space to the database. This approach means that no SQL (pun intended) is needed to get to the data, and no SQL server is between the user and the data. The connector is being developed to be extensible to multiple underlying database technologies, including direct, native access to both the MySQL Cluster "ndb" and InnoDB storage engines. The connector integrates the MySQL Cluster native API library directly within the Node.js platform itself, enabling developers to seamlessly couple their high performance, distributed applications with a high performance, distributed, persistence layer delivering 99.999% availability. The following sections take you through how to connect to MySQL, query the data and how to get started. Connecting to the database A Session is the main user access path to the database. You can get a Session object directly from the connector using the openSession function: var nosql = require("mysql-js"); var dbProperties = {     "implementation" : "ndb",     "database" : "test" }; nosql.openSession(dbProperties, null, onSession); The openSession function calls back into the application upon creating a Session. The Session is then used to create, delete, update, and read objects. Reading data The Session can read data from the database in a number of ways. If you simply want the data from the database, you provide a table name and the key of the row that you want. For example, consider this schema: create table employee (   id int not null primary key,   name varchar(32),   salary float ) ENGINE=ndbcluster; Since the primary key is a number, you can provide the key as a number to the find function. function onSession = function(err, session) {   if (err) {     console.log(err);     ... error handling   }   session.find('employee', 0, onData); }; function onData = function(err, data) {   if (err) {     console.log(err);     ... error handling   }   console.log('Found: ', JSON.stringify(data));   ... use data in application }; If you want to have the data stored in your own domain model, you tell the connector which table your domain model uses, by specifying an annotation, and pass your domain model to the find function. var annotations = new nosql.Annotations(); function Employee = function(id, name, salary) {   this.id = id;   this.name = name;   this.salary = salary;   this.giveRaise = function(percent) {     this.salary *= percent;   } }; annotations.mapClass(Employee, {'table' : 'employee'}); function onSession = function(err, session) {   if (err) {     console.log(err);     ... error handling   }   session.find(Employee, 0, onData); }; Updating data You can update the emp instance in memory, but to make the raise persistent, you need to write it back to the database, using the update function. function onData = function(err, emp) {   if (err) {     console.log(err);     ... error handling   }   console.log('Found: ', JSON.stringify(emp));   emp.giveRaise(0.12); // gee, thanks!   session.update(emp); // oops, session is out of scope here }; Using JavaScript can be tricky because it does not have the concept of block scope for variables. You can create a closure to handle these variables, or use a feature of the connector to remember your variables. The connector api takes a fixed number of parameters and returns a fixed number of result parameters to the callback function. But the connector will keep track of variables for you and return them to the callback. So in the above example, change the onSession function to remember the session variable, and you can refer to it in the onData function: function onSession = function(err, session) {   if (err) {     console.log(err);     ... error handling   }   session.find(Employee, 0, onData, session); }; function onData = function(err, emp, session) {   if (err) {     console.log(err);     ... error handling   }   console.log('Found: ', JSON.stringify(emp));   emp.giveRaise(0.12); // gee, thanks!   session.update(emp, onUpdate); // session is now in scope }; function onUpdate = function(err, emp) {   if (err) {     console.log(err);     ... error handling   } Inserting data Inserting data requires a mapped JavaScript user function (constructor) and a session. Create a variable and persist it: function onSession = function(err, session) {   var data = new Employee(999, 'Mat Keep', 20000000);   session.persist(data, onInsert);   } }; Deleting data To remove data from the database, use the session remove function. You use an instance of the domain object to identify the row you want to remove. Only the key field is relevant. function onSession = function(err, session) {   var key = new Employee(999);   session.remove(Employee, onDelete);   } }; More extensive queries We are working on the implementation of more extensive queries along the lines of the criteria query api. Stay tuned. How to evaluate The MySQL Connector for JavaScript is available for download from labs.mysql.com. Select the build: MySQL-Cluster-NoSQL-Connector-for-Node-js You can also clone the project on GitHub Since it is still early in development, feedback is especially valuable (so don't hesitate to leave comments on this blog, or head to the MySQL Cluster forum). Try it out and see how easy (and fast) it is to integrate MySQL Cluster into your Node.js platforms. You can learn more about other previewed functionality of MySQL Cluster 7.3 here

    Read the article

  • Using Squid on Debian, Cannot Connect Error

    - by Zed Said
    I am trying to set up Squid on Debian and am getting a connection refused error: squidclient http://www.apple.com/ > test client: ERROR: Cannot connect to 127.0.0.1:3128: Connection refused Here is my config: visible_hostname none cache_effective_user proxy cache_effective_group proxy cache_dir ufs /var/spool/squid 2048 16 256 cache_mem 512 MB cache_access_log /var/log/squid/access.log emulate_httpd_log on strip_query_terms off read_ahead_gap 128 Kb collapsed_forwarding on refresh_stale_hit 30 seconds retry_on_error on maximum_object_size_in_memory 1 MB acl all src 0.0.0.0/0.0.0.0 acl purgehosts src 127.0.0.1/255.255.255.255 # Caching static objects in __data is important. # Without that, apache processes sit around spooling static objects. acl QUERY urlpath_regex /cgi-bin/ /_edit /_admin /_login /_nocache /_recache /__lib /__fudge acl PURGE method PURGE acl POST method POST cache deny QUERY cache deny POST http_access allow PURGE purgehosts http_access deny PURGE http_access allow all http_port 127.0.0.1:80 http_port 50.56.206.139:80 cache_peer 127.0.0.1 parent 80 0 originserver no-query no-digest default redirect_rewrites_host_header off read_ahead_gap 128 Kb shutdown_lifetime 5 seconds Any ideas why this is happening? What have I missed?

    Read the article

  • Is it possible to skip .rvmrc confirmation?

    - by Viacheslav Molokov
    We are using RVM for managing Ruby installations and environments. Usually we are using this .rvmrc script: #!/bin/bash if [ ! -e '.version' ]; then VERSION=`pwd | sed 's/[a-z/-]//g'` echo $VERSION > .version rvm gemset create $VERSION fi VERSION=`cat .version` rvm use 1.9.2@$VERSION This script forces RVM to create new gem environment for each our project/version. But each time we was deploying new version RVM asks us to confirm new .rvmrc file. When we cd to this directory first time, we are getting something like: =============================================================== = NOTICE: = =============================================================== = RVM has encountered a not yet trusted .rvmrc file in the = = current working directory which may contain nasty code. = = = = Examine the contents of this file to be sure the contents = = are good before trusting it! = = = = Press 'q' to exit the reader when finished reading the file = =============================================================== (press enter to continue when ready) This is not as bad for development environments, but with auto deploy it require to manually confirm each new version on each server. Is it possible to skip this confirmation?

    Read the article

  • Why is (free_space + used_space) != total_size in df? [migrated]

    - by Timothy Jones
    I have a ~2TB ext4 USB external disk which is about half full: $ df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sdc 1922860848 927384456 897800668 51% /media/big I'm wondering why the total size (1922860848) isn't the same as Used+Available (1825185124)? From this answer I see that 5% of the disk might be reserved for root, but that would still only take the total used to 1921328166, which is still off. Is it related to some other filesystem overhead? In case it's relevant, lsof -n | grep deleted shows no deleted files on this disk, and there are no other filesystems mounted inside this one.

    Read the article

  • Secondary IP (eth0:0) acts like main server IP

    - by George Tasioulis
    I have a CentOS server, configured with 4 consecutive IPs: eth0 5.x.x.251 eth0:0 5.x.x.252 eth0:1 5.x.x.253 eth0:2 5.x.x.254 The problem is that all traffic goes out to the internet with eth0:0 (5.x.x.252) as the source IP, instead of eth0. # curl ifconfig.me 5.x.x.252 How can I fix this, so that all traffic goes out via eth0, ie my main IP? PS: My server is VPS running on a Xen dom0, the latter being configured in routed mode networking. Thanks in advance! Server configuration # ifconfig eth0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.251 Bcast:5.x.x.255 Mask:255.255.255.255 inet6 addr: fe80::x:x:x:x/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14675569 errors:0 dropped:0 overruns:0 frame:0 TX packets:9463227 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4122016502 (3.8 GiB) TX bytes:25959110751 (24.1 GiB) Interrupt:23 eth0:0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.252 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:1 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.253 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:2 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.254 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 # cat /etc/hosts 127.0.0.1 localhost.localdomain localhost 5.x.x.251 [fqdn] [hostname] # cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.251 NETMASK=255.255.255.224 SCOPE="peer 5.x.y.82" # cat ifcfg-eth0:0 DEVICE=eth0:0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.252 NETMASK=255.255.255.224 # cat route-eth0 ADDRESS0=0.0.0.0 NETMASK0=0.0.0.0 GATEWAY0=5.x.y.82 # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 5.x.y.82 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 5.x.x.224 0.0.0.0 255.255.255.224 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 5.x.y.82 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • using python Paramiko for ssh: sudo: no tty present and no askpass program specified

    - by misteryes
    I want to use paramiko to ssh into a bunch a remote nodes and run some command line with root priviledge I have ssh key in my home directory and so i don't need to input password when I ssh into those remote nodes but when running the following script: def connect(hostname): ssh = paramiko.SSHClient() ssh.set_missing_host_key_policy(paramiko.AutoAddPolicy()) ssh.connect(hostname, username='niky', pkey=paramiko.RSAKey.from_private_key(open('id_rsa'), 'passwd'), timeout = 240.0) return ssh def run(hostname): ssh = connect(hostname) (stdin, stdout, stderr) = ssh.exec_command("sudo ls") res = stderr.readlines() print hostname+': '+''.join(str(elem) for elem in res)+'\n' run(remote.nity.com) I got the following error: remote.nity.com: sudo: no tty present and no askpass program specified if I don't add sudo before ls everything works fine what are potential reasons ? thanks!

    Read the article

  • 2 nics. 2 Defaults Gateways

    - by andre.dias
    Here is my scenario: i have this server with 2 nics, each one with different IPs, connected to differents routers. Almost everything is configured whe way i need. Traffic coming from eth0 exits using eth0, traffic coming from eth1 exits using eth1. And there is a default gateway configured. $route: default IP 0.0.0.0 UG 0 0 0 eth0 With this configuration, the traffic generated in the server is going out using eth0 (lynx www.google.com for example). The problem is: the Internet link from eth0 went down today. The traffic coming from eth1 was ok...no problem. But the traffic generated in the server was a problem...the default gateway was out...no access do the Internet anymore (no more lynx www.google.com) So i added a new default gateway configuration, pointing to eth1. For 30 minutes i kept that way...2 default gateways, but just one was "working"...and everything was working just fine. But then i removed de eth0 gateway entry because, well, 2 default gateways is kind of weird. My question: is there any problem on keeping these 2 default gateways, one for each? So i don´t need to do nothing when one link go down again? $route: default IP1 0.0.0.0 UG 0 0 0 eth0 default IP2 0.0.0.0 UG 0 0 0 eth1

    Read the article

  • iftop Shows Lots of Mysterious Connections - Not Showing in netstat

    - by HOLOGRAPHICpizza
    I've just stopped all pretty much all services except sshd on my server (Ubuntu Server 10.04), and when I run iftop I get output that looks like this: 12.5Kb 25.0Kb 37.5Kb 50.0Kb 62.5Kb mqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqq flash.gateway.2wire.net:ssh <=> 172.16.1.151:60405 1.75Kb 1.54Kb 2.22Kb flash.gateway.2wire.net:21095 <=> 69.127.29.20:32582 536b 107b 27b flash.gateway.2wire.net:21095 <=> 190.164.122.134:13557 0b 105b 26b flash.gateway.2wire.net:21095 <=> 79.165.212.195:45138 0b 105b 26b flash.gateway.2wire.net:21095 <=> 151.42.15.151:9031 0b 72b 18b flash.gateway.2wire.net:21095 <=> 88.185.120.179:51413 0b 0b 49b flash.gateway.2wire.net:21095 <=> 178.120.152.97:25924 0b 0b 29b flash.gateway.2wire.net:21095 <=> 109.110.217.77:27868 0b 0b 26b flash.gateway.2wire.net:21095 <=> 84.13.201.90:16509 0b 0b 26b flash.gateway.2wire.net:21095 <=> 171.7.125.224:11777 0b 0b 26b flash.gateway.2wire.net:21095 <=> 115.177.164.170:21360 0b 0b 26b flash.gateway.2wire.net:21095 <=> 50.88.126.18:25540 0b 0b 25b flash.gateway.2wire.net:21095 <=> 223.206.230.163:13431 0b 0b 25b flash.gateway.2wire.net:21095 <=> 78.144.187.26:24515 0b 0b 25b flash.gateway.2wire.net:21095 <=> 83.20.61.211:27572 0b 0b 25b flash.gateway.2wire.net:21095 <=> 82.134.151.42:18448 0b 0b 18b flash.gateway.2wire.net:21095 <=> 126.117.95.247:25316 0b 0b 18b flash.gateway.2wire.net:21095 <=> 116.202.65.230:9044 0b 0b 18b flash.gateway.2wire.net:21095 <=> 88.120.63.205:51413 0b 0b 17b qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cumm: 61.6KB peak: 8.00Kb rates: 1.59Kb 1.38Kb 2.04Kb RX: 18.4KB 1.64Kb 696b 549b 640b TOTAL: 80.0KB 9.64Kb 2.27Kb 1.92Kb 2.66Kb This is the first part (not the unix socket part) of the output of netstat -a: Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:55677 *:* LISTEN tcp 0 0 flash.gateway.2wire:ssh 172.16.1.151:60405 ESTABLISHED tcp 0 48 flash.gateway.2wire:ssh 172.16.1.151:60661 ESTABLISHED tcp6 0 0 [::]:ssh [::]:* LISTEN udp 0 0 *:37790 *:* What could all those strange connections on port 21095 be? And why would they not show up in netstat?? Any advice would be greatly appreciated.

    Read the article

  • Cron stopped working, partially working.

    - by Robi
    Our cron script stopped working in different dates in August. What can be the possible reasons? We did not change anything. Our hosting showed us a log where we can see that cron is executing our scripts. But, nothing is happening in our scripts. If we manually execute the scripts, we're getting correct results like before. I showed the commands to hosting and they showed me that the commands are working. What should I tell my hosting? what should I do? They are php scripts which are executed by CRON and they just post to facebook and twitter. They don't execute any hard or huge things. I even asked my hosting if we broke any rules.

    Read the article

  • Machine check events logged

    - by GoldenNewby
    In /var/log/messages, this error occurred: Sep 19 13:18:15 wdc kernel: [2772302.630416] Machine check events logged Shortly there after, the entire server became unresponsive. This is in the log of the Dom0 for a Xen Server (running the latest version on Debian Squeeze). Can anyone shed some light on what this error means? Should I be ordering new hardware? Edit: Also, it seems to imply it logged something, where can I find that?

    Read the article

  • Can I completely remove the Windows DNS in favour of BIND9 in an AD network?

    - by Vinícius Ferrão
    I would like to remove the DNS feature of Windows Domain Controllers and point the DNS servers to our BIND9 servers. I know it's possible to setup coexistence but this requires a number of extra Windows DNS Servers equals to the number of Domain Controllers in the network. Active Directory expects the _msdcs zone and other things like _tcp, _udp; etc. The main question is: how to make BIND9 takes care of all this AD specific data? And with dynamic updating to make AD even more happier. Thanks, PS: Making BIND9 points to the Windows DNS Servers to resolve the Active Directory specific zones isn't an option. We already do this... EDIT: As today, I'm running without Windows DNS. I'm writing up a guide on how to do this, and I'll update this topic.

    Read the article

  • Protect Gnome Screen Saver Settings

    - by Jared Brown
    By default in Gnome standard users can access their screensaver preferences and change settings such as the idle time and whether or not it locks the screen. I desire to set the screensaver settings as the root user for each user and only allow the root user to adjust them. What is the best (read: simplest + fool proof) way to accomplish this?

    Read the article

  • Debugging Samba/CUPS printer sharing with Windows

    - by mrdrbob
    I've got a HP Deskjet hooked up to a Slackware 12.2 box. I've got CUPS set up and can print a test page from the box just fine. I've also got Samba set up and have a couple file shares that work fine. I'm trying to share that HP Deskjet out via Samba, but I can't get it to show up in any Windows system. I see the server and its file shares in Windows networking, but when I open the Printers, no printer shows up. Running net view \\servername from the command line lists the file shares, but no printers. Here's the pertinent part of my smb.conf, if that helps: [global] workgroup = HOMENET security = share hosts allow = 192.168.1. 192.168.2. 127. load printers = yes printcap name = cups printing = cups log file = /var/log/samba.%m max log size = 50 [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes writable = no printable = yes guest only = yes Can anyone give me some pointers as to where to start looking for potential causes? Update: Running testparm shows no errors. Here's the output (minus the file shares): [global] workgroup = HOMENET security = SHARE log file = /var/log/samba.%m max log size = 50 printcap name = cups hosts allow = 192.168.1., 192.168.2., 127. [printers] comment = All Printers path = /var/spool/samba guest only = Yes guest ok = Yes printable = Yes browseable = No

    Read the article

  • Best option for storage clustering

    - by sam
    I'm working on an application that requires a large amount of storage space and I want to handle storage 'in-house' (Much cheaper than, say, S3) so we will have multiple servers (Initially 4) with large amounts of storage (6TB each). The storage will need to be very flexible and configurable, each piece of data should be replicated on at least 2 servers and must be easily readable/writable from ether an API of a UNIX device/file/folder like a normal drive, I don't mind which. We must also be able to easily offload content to our HTTP CDN (Edgecast), it doesn't need to have built in HTTP support but if it doesn't I'm going to have to write something to get the files onto HTTP so they can be pulled by the CDN. I've looked at a lot of solutions including Eucalyptus Walrus OpenStack Object Storage MogileFS and some others which I can't remember All the servers will be running RHEL 6, they have 4x1.5TB drives which will be RAID1'd into a single partition. All the servers have 1GB/s connections between them and 100MB/s connections to the internet with unlimited bandwidth. They have 2x2.66ghz processors. I understand there isn't a single, perfect answer but it would be nice to get some pointers.

    Read the article

  • Is it possible for root to execute a command as non-root

    - by adnan kamili
    I am root user and suppose i want to run any application as another user. is it possible, without switching to another user. Something like # google-chrome user=abc I am actually executing a cli program as a non root user. I have set the sticky bit on and i am using setuid. So the program runs with root privileges. Now i am using system() with in the program to invoke gui app. But i dont want to run it as root. so i want to temporarily drop root privileges only for that call.

    Read the article

  • Determine the time difference between two linux servers

    - by Paul
    I am troubleshooting a latency network issue on a network. It is probably a nic or cabling issue, but while I was going through the process of figuring it out, I was looking at the timings of a ping packet leaving a network card and arriving at another server. Both linux. So I have tcpdump running on both, and I issue a ping from one to the other, and back again, and looking at the timing differences might have shed light on where the latency is coming from. It is an academic exercise now, as I need to eliminate some more fundamental causes, but I was curious as to how this could be achieved. Given that ntpd is installed and running on two servers, how can I confirm the current time discrepency between the two servers, to whatever level of accuracy is possible - given that we are talking about latency on a local lan, which is ideally a millisecond or so. NTP itself is accurate to a couple of ms under good conditions, and as both servers are in the same environment, they should (presumably) achieve a similar level of accuracy, and so should have a time discrepency between them of a only few ms - but how can I check this?

    Read the article

  • Pecl install ssh2, make failed

    - by user28259
    Hi! I'm trying really hard since two hours to install ssh2 with pecl... But all I get is: /bin/sh /root/ssh2-0.11.0/libtool --mode=compile cc -I. -I/root/ssh2-0.11.0 -DPHP_ATOM_INC -I/root/ssh2-0.11.0/include -I/root/ssh2-0.11.0/main -I/root/ssh2-0.11.0 -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -DHAVE_CONFIG_H -g -O2 -c /root/ssh2-0.11.0/ssh2.c -o ssh2.lo mkdir .libs cc -I. -I/root/ssh2-0.11.0 -DPHP_ATOM_INC -I/root/ssh2-0.11.0/include -I/root/ssh2-0.11.0/main -I/root/ssh2-0.11.0 -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -DHAVE_CONFIG_H -g -O2 -c /root/ssh2-0.11.0/ssh2.c -fPIC -DPIC -o .libs/ssh2.o /root/ssh2-0.11.0/ssh2.c:52: error: duplicate 'static' /root/ssh2-0.11.0/ssh2.c: In function 'zif_ssh2_methods_negotiated': /root/ssh2-0.11.0/ssh2.c:503: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:504: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:508: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:509: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:510: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:511: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:516: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:517: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:518: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c:519: warning: passing argument 4 of 'add_assoc_string_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:360: note: expected 'char *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c: In function 'zif_ssh2_publickey_add': /root/ssh2-0.11.0/ssh2.c:1045: warning: passing argument 1 of '_efree' discards qualifiers from pointer target type /usr/include/php/Zend/zend_alloc.h:46: note: expected 'void *' but argument is of type 'const char *' /root/ssh2-0.11.0/ssh2.c: In function 'zif_ssh2_publickey_list': /root/ssh2-0.11.0/ssh2.c:1104: warning: passing argument 4 of 'add_assoc_stringl_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:361: note: expected 'char *' but argument is of type 'const unsigned char *' /root/ssh2-0.11.0/ssh2.c:1105: warning: passing argument 4 of 'add_assoc_stringl_ex' discards qualifiers from pointer target type /usr/include/php/Zend/zend_API.h:361: note: expected 'char *' but argument is of type 'const unsigned char *' make: *** [ssh2.lo] Error 1 I looked on google a lot, I found some patches which didn't worked at all. So if you think you could help me, go ahead! Thanks!

    Read the article

< Previous Page | 606 607 608 609 610 611 612 613 614 615 616 617  | Next Page >