android virtual device - Page 632

Installation doesn't detect existing partitions

- by retrac1324

I am trying to install Ubuntu 11.10 in a dual boot with my existing Windows 7 but the installer does not detect any existing partitions. I have tried resetting my BCD using EasyBCD and doing fixmbr from the Windows startup disc. A while ago I had to use TestDisk to recover my partition table so this might be the cause but I have installed Ubuntu and Windows many times before with no problems. fdisk -l output: Disk /dev/sda: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x360555e5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 1250274689 625136321 7 HPFS/NTFS/exFAT Disk /dev/sdf: 7803 MB, 7803174912 bytes 255 heads, 63 sectors/track, 948 cylinders, total 15240576 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x6f795a8d Device Boot Start End Blocks Id System /dev/sdf1 * 63 15240575 7620256+ c W95 FAT32 (LBA)

Read the article

SQL Server and Hyper-V Dynamic Memory Part 2

- by SQLOS Team

Part 1 of this series was an introduction and overview of Hyper-V Dynamic Memory. This part looks at SQL Server memory management and how the SQL engine responds to changing OS memory conditions. Part 2: SQL Server Memory Management As with any Windows process, sqlserver.exe has a virtual address space (VAS) of 4GB on 32-bit and 8TB in 64-bit editions. Pages in its VAS are mapped to pages in physical memory when the memory is committed and referenced for the first time. The collection of VAS pages that have been recently referenced is known as the Working Set. How and when SQL Server allocates virtual memory and grows its working set depends on the memory model it uses. SQL Server supports three basic memory models: 1. Conventional Memory Model The Conventional model is the default SQL Server memory model and has the following properties: - Dynamic - can grow or shrink its working set in response to load and external (operating system) memory conditions. - OS uses 4K pages – (not to be confused with SQL Server “pages” which are 8K regions of committed memory).- Pageable - Can be paged out to disk by the operating system. 2. Locked Page Model The locked page memory model is set when SQL Server is started with "Lock Pages in Memory" privilege*. It has the following characteristics: - Dynamic - can grow or shrink its working set in the same way as the Conventional model.- OS uses 4K pages - Non-Pageable – When memory is committed it is locked in memory, meaning that it will remain backed by physical memory and will not be paged out by the operating system. A common misconception is to interpret "locked" as non-dynamic. A SQL Server instance using the locked page memory model will grow and shrink (allocate memory and release memory) in response to changing workload and OS memory conditions in the same way as it does with the conventional model. This is an important consideration when we look at Hyper-V Dynamic Memory – “locked” memory works perfectly well with “dynamic” memory. * Note in “Denali” (Standard Edition and above), and in SQL 2008 R2 64-bit (Enterprise and above editions) the Lock Pages in Memory privilege is all that is required to set this model. In 2008 R2 64-Bit standard edition it also requires trace flag 845 to be set, in 2008 R2 32-bit editions it requires sp_configure 'awe enabled' 1. 3. Large Page Model The Large page model is set using trace flag 834 and potentially offers a small performance boost for systems that are configured with large pages. It is characterized by: - Static - memory is allocated at startup and does not change. - OS uses large (>2MB) pages - Non-Pageable The large page model is supported with Hyper-V Dynamic Memory (and Hyper-V also supports large pages), but you get no benefit from using Dynamic Memory with this model since SQL Server memory does not grow or shrink. The rest of this article will focus on the locked and conventional SQL Server memory models. When does SQL Server grow? For “dynamic” configurations (Conventional and Locked memory models), the sqlservr.exe process grows – allocates and commits memory from the OS – in response to a workload. As much memory is allocated as is required to optimally run the query and buffer data for future queries, subject to limitations imposed by: - SQL Server max server memory setting. If this configuration option is set, the buffer pool is not allowed to grow to more than this value. In SQL Server 2008 this value represents single page allocations, and in “Denali” it represents any size page allocations and also managed CLR procedure allocations. - Memory signals from OS. The operating system sets a signal on memory resource notification objects to indicate whether it has memory available or whether it is low on available memory. If there is only 32MB free for every 4GB of memory a low memory signal is set, which continues until 64MB/4GB is free. If there is 96MB/4GB free the operating system sets a high memory signal. SQL Server only allocates memory when the high memory signal is set. To summarize, for SQL Server to grow you need three conditions: a workload, max server memory setting higher than the current allocation, high memory signals from the OS. When does SQL Server shrink caches? SQL Server as a rule does not like to return memory to the OS, but it will shrink its caches in response to memory pressure. Memory pressure can be divided into “internal” and “external”. - External memory pressure occurs when the operating system is running low on memory and low memory signals are set. The SQL Server Resource Monitor checks for low memory signals approximately every 5 seconds and it will attempt to free memory until the signals stop. To free memory SQL Server does the following: · Frees unused memory. · Notifies Memory Manager Clients to release memory o Caches – Free unreferenced cache objects. o Buffer pool - Based on oldest access times. The freed memory is released back to the operating system. This process continues until the low memory resource notifications stop. - Internal memory pressure occurs when the size of different caches and allocations increase but the SQL Server process needs to keep its total memory within a target value. For example if max server memory is set and certain caches are growing large, it will cause SQL to free memory for re-use internally, but not to release memory back to the OS. If you lower the value of max server memory you will generate internal memory pressure that will cause SQL to release memory back to the OS. Memory pressure handling has not changed much since SQL 2005 and it was described in detail in a blog post by Slava Oks. Note that SQL Server Express is an exception to the above behavior. Unlike other editions it does not assume it is the most important process running on the system but tries to be more “desktop” friendly. It will empty its working set after a period of inactivity. How does SQL Server respond to changing OS memory? In SQL Server 2005 support for Hot-Add memory was introduced. This feature, available in Enterprise and above editions, allows the server to make use of any extra physical memory that was added after SQL Server started. Being able to add physical memory when the system is running is limited to specialized hardware, but with the Hyper-V Dynamic Memory feature, when new memory is allocated to a guest virtual machine, it looks like hot-add physical memory to the guest. What this means is that thanks to the hot-add memory feature, SQL Server 2005 and higher can dynamically grow if more “physical” memory is granted to a guest VM by Hyper-V dynamic memory. SQL Server checks OS memory every second and dynamically adjusts its “target” (based on available OS memory and max server memory) accordingly. In “Denali” Standard Edition will also have sqlserver.exe support for hot-add memory when running virtualized (i.e. detecting and acting on Hyper-V Dynamic Memory allocations). How does a SQL Server workload in a guest VM impact Hyper-V dynamic memory scheduling? When a SQL workload causes the sqlserver.exe process to grow its working set, the Hyper-V memory scheduler will detect memory pressure in the guest VM and add memory to it. SQL Server will then detect the extra memory and grow according to workload demand. In our tests we have seen this feedback process cause a guest VM to grow quickly in response to SQL workload - we are still working on characterizing this ramp-up. How does SQL Server respond when Hyper-V removes memory from a guest VM through ballooning? If pressure from other VM's cause Hyper-V Dynamic Memory to take memory away from a VM through ballooning (allocating memory with a virtual device driver and returning it to the host OS), Windows Memory Manager will page out unlocked portions of memory and signal low resource notification events. When SQL Server detects these events it will shrink memory until the low memory notifications stop (see cache shrinking description above). This raises another question. Can we make SQL Server release memory more readily and hence behave more "dynamically" without compromising performance? In certain circumstances where the application workload is predictable it may be possible to have a job which varies "max server memory" according to need, lowering it when the engine is inactive and raising it before a period of activity. This would have limited applicaability but it is something we're looking into. What Memory Management changes are there in SQL Server “Denali”? In SQL Server “Denali” (aka SQL11) the Memory Manager has been re-written to be more efficient. The main changes are summarized in this post. An important change with respect to Hyper-V Dynamic Memory support is that now the max server memory setting includes any size page allocations and managed CLR procedure allocations it now represents a closer approximation to total sqlserver.exe memory usage. This makes it easier to calculate a value for max server memory, which becomes important when configuring virtual machines to work well with Hyper-V Dynamic Memory Startup and Maximum RAM settings. Another important change is no more AWE or hot-add support for 32-bit edition. This means if you're running a 32-bit edition of Denali you're limited to a 4GB address space and will not be able to take advantage of dynamically added OS memory that wasn't present when SQL Server started (though Hyper-V Dynamic Memory is still a supported configuration). In part 3 we’ll develop some best practices for configuring and using SQL Server with Dynamic Memory. Originally posted at http://blogs.msdn.com/b/sqlosteam/

Read the article

Preparing for Those ‘Requests for Tech Help’ Ahead of Time Can Pay Off [Humorous Image]

- by Asian Angel

We have all been there…waiting for the inevitable ‘repeat request’ for help, but ‘sometimes’ you can save the day ahead of time with a little bit of preparation! Then there are the times when it is just best to admit defeat… Found this today while working on a clients completely hosed PC… [Reddit IIIIIIITTTTTTTTTTTT] [via Fail Desk] How To Use USB Drives With the Nexus 7 and Other Android Devices Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder? Why Your Android Phone Isn’t Getting Operating System Updates and What You Can Do About It

Read the article

New Product: Oracle Java ME Embedded 3.2 – Small, Smart, Connected

- by terrencebarr

The Internet of Things (IoT) is coming. And, with todays launch of the Oracle Java ME Embedded 3.2 product, Java is going to play an even greater role in it. Java in the Internet of Things By all accounts, intelligent embedded devices are penetrating the world around us – driving industrial processes, monitoring environmental conditions, providing better health care, analyzing and processing data, and much more. And these devices are becoming increasingly connected, adding another dimension of utility. Welcome to the Internet of Things. As I blogged yesterday, this is a huge opportunity for the Java technology and ecosystem. To enable and utilize these billions of devices effectively you need a programming model, tools, and protocols which provide a feature-rich, consistent, scalable, manageable, and interoperable platform. Java technology is ideally suited to address these technical and business problems, enabling you eliminate many of the typical challenges in designing embedded solutions. By using Java you can focus on building smarter, more valuable embedded solutions faster. To wit, Java technology is already powering around 10 billion devices worldwide. Delivering on this vision and accelerating the growth of embedded Java solutions, Oracle is today announcing a brand-new product: Oracle Java Micro Edition (ME) Embedded 3.2, accompanied by an update release of the Java ME Software Development Kit (SDK) to version 3.2. What is Oracle Java ME Embedded 3.2? Oracle Java ME Embedded 3.2 is a complete Java runtime client, optimized for ARM architecture connected microcontrollers and other resource-constrained systems. The product provides dedicated embedded functionality and is targeted for low-power, limited memory devices requiring support for a range of network services and I/O interfaces. What features and APIs are provided by Oracle Java ME Embedded 3.2? Oracle Java ME Embedded 3.2 is a Java ME runtime based on CLDC 1.1 (JSR-139) and IMP-NG (JSR-228). The runtime and virtual machine (VM) are highly optimized for embedded use. Also included in the product are the following optional JSRs and Oracle APIs: File I/O API’s (JSR-75) Wireless Messaging API’s (JSR-120) Web Services (JSR-172) Security and Trust Services subset (JSR-177) Location API’s (JSR-179) XML API’s (JSR-280) Device Access API Application Management System (AMS) API AccessPoint API Logging API Additional embedded features are: Remote application management system Support for continuous 24×7 operation Application monitoring, auto-start, and system recovery Application access to peripheral interfaces such as GPIO, I2C, SPIO, memory mapped I/O Application level logging framework, including option for remote logging Headless on-device debugging – source level Java application debugging over IP Connection Remote configuration of the Java VM What type of platforms are targeted by Oracle Java ME 3.2 Embedded? The product is designed for embedded, always-on, resource-constrained, headless (no graphics/no UI), connected (wired or wireless) devices with a variety of peripheral I/O. The high-level system requirements are as follows: System based on ARM architecture SOCs Memory footprint (approximate) from 130 KB RAM/350KB ROM (for a minimal, customized configuration) to 700 KB RAM/1500 KB ROM (for the full, standard configuration) Very simple embedded kernel, or a more capable embedded OS/RTOS At least one type of network connection (wired or wireless) The initial release of the product is delivered as a device emulation environment for x86/Windows desktop computers, integrated with the Java ME SDK 3.2. A standard binary of Oracle Java ME Embedded 3.2 for ARM KEIL development boards based on ARM Cortex M-3/4 (KEIL MCBSTM32F200 using ST Micro SOC STM32F207IG) will soon be available for download from the Oracle Technology Network (OTN). What types of applications can I develop with Oracle Java ME Embedded 3.2? The Oracle Java ME Embedded 3.2 product is a full-featured embedded Java runtime supporting applications based on the IMP-NG application model, which is derived from the well-known MIDP 2 application model. The runtime supports execution of multiple concurrent applications, remote application management, versatile connectivity, and a rich set of APIs and features relevant for embedded use cases, including the ability to interact with peripheral I/O directly from Java applications. This rich feature set, coupled with familiar and best-in class software development tools, allows developers to quickly build and deploy sophisticated embedded solutions for a wide range of use cases. Target markets well supported by Oracle Java ME Embedded 3.2 include wireless modules for M2M, industrial and building control, smart grid infrastructure, home automation, and environmental sensors and tracking. What tools are available for embedded application development for Oracle Java ME Embedded 3.2? Along with the release of Oracle Java ME Embedded 3.2, Oracle is also making available an updated version of the Java ME Software Development Kit (SDK), together with plug-ins for the NetBeans and Eclipse IDEs, to deliver a complete development environment for embedded application development. OK – sounds great! Where can I find out more? And how do I get started? There is a complete set of information, data sheet, API documentation, “Getting Started Guide”, FAQ, and download links available: For an overview of Oracle Embeddable Java, see here. For the Oracle Java ME Embedded 3.2 press release, see here. For the Oracle Java ME Embedded 3.2 data sheet, see here. For the Oracle Java ME Embedded 3.2 landing page, see here. For the Oracle Java ME Embedded 3.2 documentation page, including a “Getting Started Guide” and FAQ, see here. For the Oracle Java ME SDK 3.2 landing and download page, see here. Finally, to ask more questions, please see the OTN “Java ME Embedded” forum To get started, grab the “Getting Started Guide” and download the Java ME SDK 3.2, which includes the Oracle Java ME Embedded 3.2 device emulation. Can I learn more about Oracle Java ME Embedded 3.2 at JavaOne and/or Java Embedded @ JavaOne? Glad you asked Both conferences, JavaOne and Java Embedded @ JavaOne, will feature a host of content and information around the new Oracle Java ME Embedded 3.2 product, from technical and business sessions, to hands-on tutorials, and demos. Stay tuned, I will post details shortly. Cheers, – Terrence Filed under: Mobile & Embedded Tagged: "Oracle Java ME Embedded", Connected, embedded, Embedded Java, Java Embedded @ JavaOne, JavaOne, Smart

Read the article

Using Durandal to Create Single Page Apps

- by Stephen.Walther

A few days ago, I gave a talk on building Single Page Apps on the Microsoft Stack. In that talk, I recommended that people use Knockout, Sammy, and RequireJS to build their presentation layer and use the ASP.NET Web API to expose data from their server. After I gave the talk, several people contacted me and suggested that I investigate a new open-source JavaScript library named Durandal. Durandal stitches together Knockout, Sammy, and RequireJS to make it easier to use these technologies together. In this blog entry, I want to provide a brief walkthrough of using Durandal to create a simple Single Page App. I am going to demonstrate how you can create a simple Movies App which contains (virtual) pages for viewing a list of movies, adding new movies, and viewing movie details. The goal of this blog entry is to give you a sense of what it is like to build apps with Durandal. Installing Durandal First things first. How do you get Durandal? The GitHub project for Durandal is located here: https://github.com/BlueSpire/Durandal The Wiki — located at the GitHub project — contains all of the current documentation for Durandal. Currently, the documentation is a little sparse, but it is enough to get you started. Instead of downloading the Durandal source from GitHub, a better option for getting started with Durandal is to install one of the Durandal NuGet packages. I built the Movies App described in this blog entry by first creating a new ASP.NET MVC 4 Web Application with the Basic Template. Next, I executed the following command from the Package Manager Console: Install-Package Durandal.StarterKit As you can see from the screenshot of the Package Manager Console above, the Durandal Starter Kit package has several dependencies including: · jQuery · Knockout · Sammy · Twitter Bootstrap The Durandal Starter Kit package includes a sample Durandal application. You can get to the Starter Kit app by navigating to the Durandal controller. Unfortunately, when I first tried to run the Starter Kit app, I got an error because the Starter Kit is hard-coded to use a particular version of jQuery which is already out of date. You can fix this issue by modifying the App_Start\DurandalBundleConfig.cs file so it is jQuery version agnostic like this: bundles.Add( new ScriptBundle("~/scripts/vendor") .Include("~/Scripts/jquery-{version}.js") .Include("~/Scripts/knockout-{version}.js") .Include("~/Scripts/sammy-{version}.js") // .Include("~/Scripts/jquery-1.9.0.min.js") // .Include("~/Scripts/knockout-2.2.1.js") // .Include("~/Scripts/sammy-0.7.4.min.js") .Include("~/Scripts/bootstrap.min.js") ); The recommendation is that you create a Durandal app in a folder off your project root named App. The App folder in the Starter Kit contains the following subfolders and files: · durandal – This folder contains the actual durandal JavaScript library. · viewmodels – This folder contains all of your application’s view models. · views – This folder contains all of your application’s views. · main.js — This file contains all of the JavaScript startup code for your app including the client-side routing configuration. · main-built.js – This file contains an optimized version of your application. You need to build this file by using the RequireJS optimizer (unfortunately, before you can run the optimizer, you must first install NodeJS). For the purpose of this blog entry, I wanted to start from scratch when building the Movies app, so I deleted all of these files and folders except for the durandal folder which contains the durandal library. Creating the ASP.NET MVC Controller and View A Durandal app is built using a single server-side ASP.NET MVC controller and ASP.NET MVC view. A Durandal app is a Single Page App. When you navigate between pages, you are not navigating to new pages on the server. Instead, you are loading new virtual pages into the one-and-only-one server-side view. For the Movies app, I created the following ASP.NET MVC Home controller: public class HomeController : Controller { public ActionResult Index() { return View(); } } There is nothing special about the Home controller – it is as basic as it gets. Next, I created the following server-side ASP.NET view. This is the one-and-only server-side view used by the Movies app: @{ Layout = null; } <!DOCTYPE html> <html> <head> <title>Index</title> </head> <body> <div id="applicationHost"> Loading app.... </div> @Scripts.Render("~/scripts/vendor") <script type="text/javascript" src="~/App/durandal/amd/require.js" data-main="/App/main"></script> </body> </html> Notice that I set the Layout property for the view to the value null. If you neglect to do this, then the default ASP.NET MVC layout will be applied to the view and you will get the <!DOCTYPE> and opening and closing <html> tags twice. Next, notice that the view contains a DIV element with the Id applicationHost. This marks the area where virtual pages are loaded. When you navigate from page to page in a Durandal app, HTML page fragments are retrieved from the server and stuck in the applicationHost DIV element. Inside the applicationHost element, you can place any content which you want to display when a Durandal app is starting up. For example, you can create a fancy splash screen. I opted for simply displaying the text “Loading app…”: Next, notice the view above includes a call to the Scripts.Render() helper. This helper renders out all of the JavaScript files required by the Durandal library such as jQuery and Knockout. Remember to fix the App_Start\DurandalBundleConfig.cs as described above or Durandal will attempt to load an old version of jQuery and throw a JavaScript exception and stop working. Your application JavaScript code is not included in the scripts rendered by the Scripts.Render helper. Your application code is loaded dynamically by RequireJS with the help of the following SCRIPT element located at the bottom of the view: <script type="text/javascript" src="~/App/durandal/amd/require.js" data-main="/App/main"></script> The data-main attribute on the SCRIPT element causes RequireJS to load your /app/main.js JavaScript file to kick-off your Durandal app. Creating the Durandal Main.js File The Durandal Main.js JavaScript file, located in your App folder, contains all of the code required to configure the behavior of Durandal. Here’s what the Main.js file looks like in the case of the Movies app: require.config({ paths: { 'text': 'durandal/amd/text' } }); define(function (require) { var app = require('durandal/app'), viewLocator = require('durandal/viewLocator'), system = require('durandal/system'), router = require('durandal/plugins/router'); //>>excludeStart("build", true); system.debug(true); //>>excludeEnd("build"); app.start().then(function () { //Replace 'viewmodels' in the moduleId with 'views' to locate the view. //Look for partial views in a 'views' folder in the root. viewLocator.useConvention(); //configure routing router.useConvention(); router.mapNav("movies/show"); router.mapNav("movies/add"); router.mapNav("movies/details/:id"); app.adaptToDevice(); //Show the app by setting the root view model for our application with a transition. app.setRoot('viewmodels/shell', 'entrance'); }); }); There are three important things to notice about the main.js file above. First, notice that it contains a section which enables debugging which looks like this: //>>excludeStart(“build”, true); system.debug(true); //>>excludeEnd(“build”); This code enables debugging for your Durandal app which is very useful when things go wrong. When you call system.debug(true), Durandal writes out debugging information to your browser JavaScript console. For example, you can use the debugging information to diagnose issues with your client-side routes: (The funny looking //> symbols around the system.debug() call are RequireJS optimizer pragmas). The main.js file is also the place where you configure your client-side routes. In the case of the Movies app, the main.js file is used to configure routes for three page: the movies show, add, and details pages. //configure routing router.useConvention(); router.mapNav("movies/show"); router.mapNav("movies/add"); router.mapNav("movies/details/:id"); The route for movie details includes a route parameter named id. Later, we will use the id parameter to lookup and display the details for the right movie. Finally, the main.js file above contains the following line of code: //Show the app by setting the root view model for our application with a transition. app.setRoot('viewmodels/shell', 'entrance'); This line of code causes Durandal to load up a JavaScript file named shell.js and an HTML fragment named shell.html. I’ll discuss the shell in the next section. Creating the Durandal Shell You can think of the Durandal shell as the layout or master page for a Durandal app. The shell is where you put all of the content which you want to remain constant as a user navigates from virtual page to virtual page. For example, the shell is a great place to put your website logo and navigation links. The Durandal shell is composed from two parts: a JavaScript file and an HTML file. Here’s what the HTML file looks like for the Movies app: <h1>Movies App</h1> <div class="container-fluid page-host">  </div> And here is what the JavaScript file looks like: define(function (require) { var router = require('durandal/plugins/router'); return { router: router, activate: function () { return router.activate('movies/show'); } }; }); The JavaScript file contains the view model for the shell. This view model returns the Durandal router so you can access the list of configured routes from your shell. Notice that the JavaScript file includes a function named activate(). This function loads the movies/show page as the first page in the Movies app. If you want to create a different default Durandal page, then pass the name of a different age to the router.activate() method. Creating the Movies Show Page Durandal pages are created out of a view model and a view. The view model contains all of the data and view logic required for the view. The view contains all of the HTML markup for rendering the view model. Let’s start with the movies show page. The movies show page displays a list of movies. The view model for the show page looks like this: define(function (require) { var moviesRepository = require("repositories/moviesRepository"); return { movies: ko.observable(), activate: function() { this.movies(moviesRepository.listMovies()); } }; }); You create a view model by defining a new RequireJS module (see http://requirejs.org). You create a RequireJS module by placing all of your JavaScript code into an anonymous function passed to the RequireJS define() method. A RequireJS module has two parts. You retrieve all of the modules which your module requires at the top of your module. The code above depends on another RequireJS module named repositories/moviesRepository. Next, you return the implementation of your module. The code above returns a JavaScript object which contains a property named movies and a method named activate. The activate() method is a magic method which Durandal calls whenever it activates your view model. Your view model is activated whenever you navigate to a page which uses it. In the code above, the activate() method is used to get the list of movies from the movies repository and assign the list to the view model movies property. The HTML for the movies show page looks like this: <table> <thead> <tr> <th>Title</th><th>Director</th> </tr> </thead> <tbody data-bind="foreach:movies"> <tr> <td data-bind="text:title"></td> <td data-bind="text:director"></td> <td><a data-bind="attr:{href:'#/movies/details/'+id}">Details</a></td> </tr> </tbody> </table> <a href="#/movies/add">Add Movie</a> Notice that this is an HTML fragment. This fragment will be stuffed into the page-host DIV element in the shell.html file which is stuffed, in turn, into the applicationHost DIV element in the server-side MVC view. The HTML markup above contains data-bind attributes used by Knockout to display the list of movies (To learn more about Knockout, visit http://knockoutjs.com). The list of movies from the view model is displayed in an HTML table. Notice that the page includes a link to a page for adding a new movie. The link uses the following URL which starts with a hash: #/movies/add. Because the link starts with a hash, clicking the link does not cause a request back to the server. Instead, you navigate to the movies/add page virtually. Creating the Movies Add Page The movies add page also consists of a view model and view. The add page enables you to add a new movie to the movie database. Here’s the view model for the add page: define(function (require) { var app = require('durandal/app'); var router = require('durandal/plugins/router'); var moviesRepository = require("repositories/moviesRepository"); return { movieToAdd: { title: ko.observable(), director: ko.observable() }, activate: function () { this.movieToAdd.title(""); this.movieToAdd.director(""); this._movieAdded = false; }, canDeactivate: function () { if (this._movieAdded == false) { return app.showMessage('Are you sure you want to leave this page?', 'Navigate', ['Yes', 'No']); } else { return true; } }, addMovie: function () { // Add movie to db moviesRepository.addMovie(ko.toJS(this.movieToAdd)); // flag new movie this._movieAdded = true; // return to list of movies router.navigateTo("#/movies/show"); } }; }); The view model contains one property named movieToAdd which is bound to the add movie form. The view model also has the following three methods: 1. activate() – This method is called by Durandal when you navigate to the add movie page. The activate() method resets the add movie form by clearing out the movie title and director properties. 2. canDeactivate() – This method is called by Durandal when you attempt to navigate away from the add movie page. If you return false then navigation is cancelled. 3. addMovie() – This method executes when the add movie form is submitted. This code adds the new movie to the movie repository. I really like the Durandal canDeactivate() method. In the code above, I use the canDeactivate() method to show a warning to a user if they navigate away from the add movie page – either by clicking the Cancel button or by hitting the browser back button – before submitting the add movie form: The view for the add movie page looks like this: <form data-bind="submit:addMovie"> <fieldset> <legend>Add Movie</legend> <div> <label> Title: <input data-bind="value:movieToAdd.title" required /> </label> </div> <div> <label> Director: <input data-bind="value:movieToAdd.director" required /> </label> </div> <div> <input type="submit" value="Add" /> <a href="#/movies/show">Cancel</a> </div> </fieldset> </form> I am using Knockout to bind the movieToAdd property from the view model to the INPUT elements of the HTML form. Notice that the FORM element includes a data-bind attribute which invokes the addMovie() method from the view model when the HTML form is submitted. Creating the Movies Details Page You navigate to the movies details Page by clicking the Details link which appears next to each movie in the movies show page: The Details links pass the movie ids to the details page: #/movies/details/0 #/movies/details/1 #/movies/details/2 Here’s what the view model for the movies details page looks like: define(function (require) { var router = require('durandal/plugins/router'); var moviesRepository = require("repositories/moviesRepository"); return { movieToShow: { title: ko.observable(), director: ko.observable() }, activate: function (context) { // Grab movie from repository var movie = moviesRepository.getMovie(context.id); // Add to view model this.movieToShow.title(movie.title); this.movieToShow.director(movie.director); } }; }); Notice that the view model activate() method accepts a parameter named context. You can take advantage of the context parameter to retrieve route parameters such as the movie Id. In the code above, the context.id property is used to retrieve the correct movie from the movie repository and the movie is assigned to a property named movieToShow exposed by the view model. The movie details view displays the movieToShow property by taking advantage of Knockout bindings: <div> <h2 data-bind="text:movieToShow.title"></h2> directed by <span data-bind="text:movieToShow.director"></span> </div> Summary The goal of this blog entry was to walkthrough building a simple Single Page App using Durandal and to get a feel for what it is like to use this library. I really like how Durandal stitches together Knockout, Sammy, and RequireJS and establishes patterns for using these libraries to build Single Page Apps. Having a standard pattern which developers on a team can use to build new pages is super valuable. Once you get the hang of it, using Durandal to create new virtual pages is dead simple. Just define a new route, view model, and view and you are done. I also appreciate the fact that Durandal did not attempt to re-invent the wheel and that Durandal leverages existing JavaScript libraries such as Knockout, RequireJS, and Sammy. These existing libraries are powerful libraries and I have already invested a considerable amount of time in learning how to use them. Durandal makes it easier to use these libraries together without losing any of their power. Durandal has some additional interesting features which I have not had a chance to play with yet. For example, you can use the RequireJS optimizer to combine and minify all of a Durandal app’s code. Also, Durandal supports a way to create custom widgets (client-side controls) by composing widgets from a controller and view. You can download the code for the Movies app by clicking the following link (this is a Visual Studio 2012 project): Durandal Movie App

Read the article

Quickly and Easily Create Folders in Windows By Dragging and Dropping Files

- by Lori Kaufman

If you use iOS or Android devices, you’re familiar with the drag-and-drop method of creating folders. If you like that method of grouping files, you can get the same functionality on your Windows PC using a free utility, called Smart Folders. Smart Folders helps you quickly organize your files, such as images, documents, and audio files, without having to create separate folders before you move the files. Simply drag one file on top of another file to create a new folder. To use Smart Folders to easily create folders, double-click on the .exe file you downloaded (see the link at the end of this article). Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder? Why Your Android Phone Isn’t Getting Operating System Updates and What You Can Do About It How To Delete, Move, or Rename Locked Files in Windows

Read the article

Unable to boot Windows 7 after installing Ubuntu

- by Devendra

I have Windows 7 on my machine and then installed Ubuntu 12.04 using a live CD. I can see both Windows 7 and Ubuntu in the grub menu, but when I select Windows 7 it shows a black screen for about 2 seconds and the returns to the Grub menu. But if I select Ubuntu it's working fine. This is the contents of the boot-repair log: Boot Info Script 0.61.full + Boot-Repair extra info [Boot-Info November 20th 2012] ============================= Boot Info Summary: =============================== => Grub2 (v2.00) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for (,msdos6)/boot/grub. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Grub2 (v1.99-2.00) Boot sector info: Grub2 (v2.00) is installed in the boot sector of sda1 and looks at sector 388911128 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for (,msdos6)/boot/grub. No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda2: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda4: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: According to the info in the boot sector, sda5 starts at sector 2048. Operating System: Boot files: sda6: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.10 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/i386-pc/core.img sda7: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 206,848 146,802,687 146,595,840 7 NTFS / exFAT / HPFS /dev/sda2 147,007,488 293,623,807 146,616,320 7 NTFS / exFAT / HPFS /dev/sda3 293,623,808 332,820,613 39,196,806 7 NTFS / exFAT / HPFS /dev/sda4 332,822,526 1,465,145,343 1,132,322,818 f W95 Extended (LBA) /dev/sda5 461,342,720 1,465,145,343 1,003,802,624 7 NTFS / exFAT / HPFS /dev/sda6 332,822,528 453,171,199 120,348,672 83 Linux /dev/sda7 453,173,248 461,338,623 8,165,376 82 Linux swap / Solaris "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 F6AE2C13AE2BCB47 ntfs /dev/sda2 DC2273012272DFC6 ntfs /dev/sda3 1E76E43376E40D79 ntfs New Volume /dev/sda5 5ED60ACDD60AA57D ntfs /dev/sda6 9e70fd16-b48b-4f88-adcf-e443aef83124 ext4 /dev/sda7 52f3dd94-6be7-4a7b-a3ae-f43eb8810483 swap ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda6 / ext4 (rw,errors=remount-ro) =========================== sda6/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ x"${feature_menuentry_id}" = xy ]; then menuentry_id_option="--id" else menuentry_id_option="" fi export menuentry_id_option if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { if [ x$feature_all_video_module = xy ]; then insmod all_video else insmod efi_gop insmod efi_uga insmod ieee1275_fb insmod vbe insmod vga insmod video_bochs insmod video_cirrus fi } if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi font="/usr/share/grub/unicode.pf2" fi if loadfont $font ; then set gfxmode=auto load_video insmod gfxterm set locale_dir=$prefix/locale set lang=en_IN insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash $vt_handoff initrd /boot/initrd.img-3.5.0-17-generic } submenu 'Advanced options for Ubuntu' $menuentry_id_option 'gnulinux-advanced-9e70fd16-b48b-4f88-adcf-e443aef83124' { menuentry 'Ubuntu, with Linux 3.5.0-17-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-advanced-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } menuentry 'Ubuntu, with Linux 3.5.0-17-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-recovery-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry 'Windows 7 (loader) (on /dev/sda1)' --class windows --class os $menuentry_id_option 'osprober-chain-F6AE2C13AE2BCB47' { insmod part_msdos insmod ntfs set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 F6AE2C13AE2BCB47 else search --no-floppy --fs-uuid --set=root F6AE2C13AE2BCB47 fi chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/30_uefi-firmware ### ### END /etc/grub.d/30_uefi-firmware ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f ${config_directory}/custom.cfg ]; then source ${config_directory}/custom.cfg elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda6/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda6 during installation UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda7 during installation UUID=52f3dd94-6be7-4a7b-a3ae-f43eb8810483 none swap sw 0 0 -------------------------------------------------------------------------------- =================== sda6: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 162.831275940 = 174.838751232 boot/grub/grub.cfg 1 163.036647797 = 175.059267584 boot/initrd.img-3.5.0-17-generic 1 206.871749878 = 222.126850048 boot/vmlinuz-3.5.0-17-generic 1 163.036647797 = 175.059267584 initrd.img 1 163.036647797 = 175.059267584 initrd.img.old 1 206.871749878 = 222.126850048 vmlinuz 1 =============================== StdErr Messages: =============================== cat: write error: Broken pipe cat: write error: Broken pipe ADDITIONAL INFORMATION : =================== log of boot-repair 2012-12-11__00h59 =================== boot-repair version : 3.195~ppa28~quantal boot-sav version : 3.195~ppa28~quantal glade2script version : 3.2.2~ppa45~quantal boot-sav-extra version : 3.195~ppa28~quantal boot-repair is executed in installed-session (Ubuntu 12.10, quantal, Ubuntu, x86_64) CPU op-mode(s): 32-bit, 64-bit BOOT_IMAGE=/boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash vt.handoff=7 =================== os-prober: /dev/sda6:The OS now in use - Ubuntu 12.10 CurrentSession:linux /dev/sda1:Windows 7 (loader):Windows:chain =================== blkid: /dev/sda1: UUID="F6AE2C13AE2BCB47" TYPE="ntfs" /dev/sda2: UUID="DC2273012272DFC6" TYPE="ntfs" /dev/sda3: LABEL="New Volume" UUID="1E76E43376E40D79" TYPE="ntfs" /dev/sda5: UUID="5ED60ACDD60AA57D" TYPE="ntfs" /dev/sda6: UUID="9e70fd16-b48b-4f88-adcf-e443aef83124" TYPE="ext4" /dev/sda7: UUID="52f3dd94-6be7-4a7b-a3ae-f43eb8810483" TYPE="swap" 1 disks with OS, 2 OS : 1 Linux, 0 MacOS, 1 Windows, 0 unknown type OS. Warning: extended partition does not start at a cylinder boundary. DOS and Linux will interpret the contents differently. =================== /etc/default/grub : # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" =================== /etc/grub.d/ : drwxr-xr-x 2 root root 4096 Oct 17 20:29 grub.d total 72 -rwxr-xr-x 1 root root 7541 Oct 14 23:06 00_header -rwxr-xr-x 1 root root 5488 Oct 4 15:00 05_debian_theme -rwxr-xr-x 1 root root 10891 Oct 14 23:06 10_linux -rwxr-xr-x 1 root root 10258 Oct 14 23:06 20_linux_xen -rwxr-xr-x 1 root root 1688 Oct 11 19:40 20_memtest86+ -rwxr-xr-x 1 root root 10976 Oct 14 23:06 30_os-prober -rwxr-xr-x 1 root root 1426 Oct 14 23:06 30_uefi-firmware -rwxr-xr-x 1 root root 214 Oct 14 23:06 40_custom -rwxr-xr-x 1 root root 216 Oct 14 23:06 41_custom -rw-r--r-- 1 root root 483 Oct 14 23:06 README =================== UEFI/Legacy mode: This installed-session is not in EFI-mode. EFI in dmesg. Please report this message to [email protected] [ 0.000000] ACPI: UEFI 00000000bafe7000 0003E (v01 DELL QA09 00000002 PTL 00000002) [ 0.000000] ACPI: UEFI 00000000bafe6000 00042 (v01 PTL COMBUF 00000001 PTL 00000001) [ 0.000000] ACPI: UEFI 00000000bafe3000 00256 (v01 DELL QA09 00000002 PTL 00000002) SecureBoot disabled. =================== PARTITIONS & DISKS: sda6 : sda, not-sepboot, grubenv-ok grub2, grub-pc , update-grub, 64, with-boot, is-os, not--efi--part, fstab-without-boot, fstab-without-efi, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, apt-get, grub-install, with--usr, fstab-without-usr, not-sep-usr, standard, farbios, . sda1 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, is-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, haswinload, no-recov-nor-hid, bootmgr, is-winboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, not-far, /mnt/boot-sav/sda1. sda2 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda2. sda3 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda3. sda5 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda5. sda : not-GPT, BIOSboot-not-needed, has-no-EFIpart, not-usb, has-os, 2048 sectors * 512 bytes =================== parted -l: Model: ATA WDC WD7500BPKT-7 (scsi) Disk /dev/sda: 750GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 106MB 75.2GB 75.1GB primary ntfs boot 2 75.3GB 150GB 75.1GB primary ntfs 3 150GB 170GB 20.1GB primary ntfs 4 170GB 750GB 580GB extended lba 6 170GB 232GB 61.6GB logical ext4 7 232GB 236GB 4181MB logical linux-swap(v1) 5 236GB 750GB 514GB logical ntfs =================== parted -lm: BYT; /dev/sda:750GB:scsi:512:4096:msdos:ATA WDC WD7500BPKT-7; 1:106MB:75.2GB:75.1GB:ntfs::boot; 2:75.3GB:150GB:75.1GB:ntfs::; 3:150GB:170GB:20.1GB:ntfs::; 4:170GB:750GB:580GB:::lba; 6:170GB:232GB:61.6GB:ext4::; 7:232GB:236GB:4181MB:linux-swap(v1)::; 5:236GB:750GB:514GB:ntfs::; =================== mount: /dev/sda6 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755) gvfsd-fuse on /run/user/dev/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=dev) /dev/sda1 on /mnt/boot-sav/sda1 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda2 on /mnt/boot-sav/sda2 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda3 on /mnt/boot-sav/sda3 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda5 on /mnt/boot-sav/sda5 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) =================== ls: /sys/block/sda (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sda1 sda2 sda3 sda4 sda5 sda6 sda7 size slaves stat subsystem trace uevent /sys/block/sr0 (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro size slaves stat subsystem trace uevent /dev (filtered): alarm ashmem autofs binder block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dri dvd dvdrw ecryptfs fb0 fb1 fd full fuse hpet input kmsg kvm log mapper mcelog mei mem net network_latency network_throughput null oldmem port ppp psaux ptmx pts random rfkill rtc rtc0 sda sda1 sda2 sda3 sda4 sda5 sda6 sda7 sg0 sg1 shm snapshot snd sr0 stderr stdin stdout uinput urandom v4l vga_arbiter vhost-net video0 zero ls /dev/mapper: control =================== df -Th: Filesystem Type Size Used Avail Use% Mounted on /dev/sda6 ext4 57G 2.7G 51G 6% / udev devtmpfs 1.9G 12K 1.9G 1% /dev tmpfs tmpfs 770M 892K 769M 1% /run none tmpfs 5.0M 0 5.0M 0% /run/lock none tmpfs 1.9G 260K 1.9G 1% /run/shm none tmpfs 100M 44K 100M 1% /run/user /dev/sda1 fuseblk 70G 36G 35G 51% /mnt/boot-sav/sda1 /dev/sda2 fuseblk 70G 66G 4.8G 94% /mnt/boot-sav/sda2 /dev/sda3 fuseblk 19G 87M 19G 1% /mnt/boot-sav/sda3 /dev/sda5 fuseblk 479G 436G 44G 92% /mnt/boot-sav/sda5 =================== fdisk -l: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x1dc69d0b Device Boot Start End Blocks Id System /dev/sda1 * 206848 146802687 73297920 7 HPFS/NTFS/exFAT /dev/sda2 147007488 293623807 73308160 7 HPFS/NTFS/exFAT /dev/sda3 293623808 332820613 19598403 7 HPFS/NTFS/exFAT /dev/sda4 332822526 1465145343 566161409 f W95 Ext'd (LBA) Partition 4 does not start on physical sector boundary. /dev/sda5 461342720 1465145343 501901312 7 HPFS/NTFS/exFAT /dev/sda6 332822528 453171199 60174336 83 Linux /dev/sda7 453173248 461338623 4082688 82 Linux swap / Solaris Partition table entries are not in disk order =================== Recommended repair Recommended-Repair This setting will reinstall the grub2 of sda6 into the MBR of sda. Additional repair will be performed: unhide-bootmenu-10s grub-install (GRUB) 2.00-7ubuntu11,grub-install (GRUB) 2. Reinstall the GRUB of sda6 into the MBR of sda Installation finished. No error reported. grub-install /dev/sda: exit code of grub-install /dev/sda:0 update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.5.0-17-generic Found initrd image: /boot/initrd.img-3.5.0-17-generic Found memtest86+ image: /boot/memtest86+.bin Found Windows 7 (loader) on /dev/sda1 Unhide GRUB boot menu in sda6/boot/grub/grub.cfg Boot successfully repaired. You can now reboot your computer. The boot files of [The OS now in use - Ubuntu 12.10] are far from the start of the disk. Your BIOS may not detect them. You may want to retry after creating a /boot partition (EXT4, >200MB, start of the disk). This can be performed via tools such as gParted. Then select this partition via the [Separate /boot partition:] option of [Boot Repair]. (https://help.ubuntu.com/community/BootPartition)

Read the article

Conheça a nova Windows Azure

- by Leniel Macaferi

Hoje estamos lançando um grande conjunto de melhorias para a Windows Azure. A seguir está um breve resumo de apenas algumas destas melhorias: Novo Portal de Administração e Ferramentas de Linha de Comando O lançamento de hoje vem com um novo portal para a Windows Azure, o qual lhe permitirá gerenciar todos os recursos e serviços oferecidos na Windows Azure de uma forma perfeitamente integrada. O portal é muito rápido e fluido, suporta filtragem e classificação dos dados (o que o torna muito fácil de usar em implantações/instalações de grande porte), funciona em todos os navegadores, e oferece um monte de ótimos e novos recursos - incluindo suporte nativo à VM (máquina virtual), Web site, Storage (armazenamento), e monitoramento de Serviços hospedados na Nuvem. O novo portal é construído em cima de uma API de gerenciamento baseada no modelo REST dentro da Windows Azure - e tudo o que você pode fazer através do portal também pode ser feito através de programação acessando esta Web API. Também estamos lançando hoje ferramentas de linha de comando (que, igualmente ao portal, chamam as APIs de Gerenciamento REST) para tornar ainda ainda mais fácil a criação de scripts e a automatização de suas tarefas de administração. Estamos oferecendo para download um conjunto de ferramentas para o Powershell (Windows) e Bash (Mac e Linux). Como nossos SDKs, o código destas ferramentas está hospedado no GitHub sob uma licença Apache 2. Máquinas Virtuais ( Virtual Machines [ VM ] ) A Windows Azure agora suporta a capacidade de implantar e executar VMs duráveis/permanentes ??na nuvem. Você pode criar facilmente essas VMs usando uma nova Galeria de Imagens embutida no novo Portal da Windows Azure ou, alternativamente, você pode fazer o upload e executar suas próprias imagens VHD customizadas. Máquinas virtuais são duráveis ??(o que significa que qualquer coisa que você instalar dentro delas persistirá entre as reinicializações) e você pode usar qualquer sistema operacional nelas. Nossa galeria de imagens nativa inclui imagens do Windows Server (incluindo o novo Windows Server 2012 RC), bem como imagens do Linux (incluindo Ubuntu, CentOS, e as distribuições SUSE). Depois de criar uma instância de uma VM você pode facilmente usar o Terminal Server ou SSH para acessá-las a fim de configurar e personalizar a máquina virtual da maneira como você quiser (e, opcionalmente, capturar uma snapshot (cópia instantânea da imagem atual) para usar ao criar novas instâncias de VMs). Isto te proporciona a flexibilidade de executar praticamente qualquer carga de trabalho dentro da plataforma Windows Azure. A novo Portal da Windows Azure fornece um rico conjunto de recursos para o gerenciamento de Máquinas Virtuais - incluindo a capacidade de monitorar e controlar a utilização dos recursos dentro delas. Nosso novo suporte à Máquinas Virtuais também permite a capacidade de facilmente conectar múltiplos discos nas VMs (os quais você pode então montar e formatar como unidades de disco). Opcionalmente, você pode ativar o suporte à replicação geográfica (geo-replication) para estes discos - o que fará com que a Windows Azure continuamente replique o seu armazenamento em um data center secundário (criando um backup), localizado a pelo menos 640 quilômetros de distância do seu data-center principal. Nós usamos o mesmo formato VHD que é suportado com a virtualização do Windows hoje (o qual nós lançamos como uma especificação aberta), de modo a permitir que você facilmente migre cargas de trabalho existentes que você já tenha virtualizado na Windows Azure. Também tornamos fácil fazer o download de VHDs da Windows Azure, o que também oferece a flexibilidade para facilmente migrar cargas de trabalho das VMs baseadas na nuvem para um ambiente local. Tudo o que você precisa fazer é baixar o arquivo VHD e inicializá-lo localmente - nenhuma etapa de importação/exportação é necessária. Web Sites A Windows Azure agora suporta a capacidade de rapidamente e facilmente implantar web-sites ASP.NET, Node.js e PHP em um ambiente na nuvem altamente escalável que te permite começar pequeno (e de maneira gratuita) de modo que você possa em seguida, adaptar/escalar sua aplicação de acordo com o crescimento do seu tráfego. Você pode criar um novo web site na Azure e tê-lo pronto para implantação em menos de 10 segundos: O novo Portal da Windows Azure oferece suporte integrado para a administração de Web sites, incluindo a capacidade de monitorar e acompanhar a utilização dos recursos em tempo real: Você pode fazer o deploy (implantação) para web-sites em segundos usando FTP, Git, TFS e Web Deploy. Também estamos lançando atualizações para as ferramentas do Visual Studio e da Web Matrix que permitem aos desenvolvedores uma fácil instalação das aplicações ASP.NET nesta nova oferta. O suporte de publicação do VS e da Web Matrix inclui a capacidade de implantar bancos de dados SQL como parte da implantação do site - bem como a capacidade de realizar a atualização incremental do esquema do banco de dados com uma implantação realizada posteriormente. Você pode integrar a publicação de aplicações web com o controle de código fonte ao selecionar os links "Set up TFS publishing" (Configurar publicação TFS) ou "Set up Git publishing" (Configurar publicação Git) que estão presentes no dashboard de um web-site: Ao fazer isso, você habilitará a integração com o nosso novo serviço online TFS (que permite um fluxo de trabalho do TFS completo - incluindo um build elástico e suporte a testes), ou você pode criar um repositório Git e referenciá-lo como um remote para executar implantações automáticas. Uma vez que você executar uma implantação usando TFS ou Git, a tab/guia de implantações/instalações irá acompanhar as implantações que você fizer, e permitirá que você selecione uma implantação mais antiga (ou mais recente) para que você possa rapidamente voltar o seu site para um estado anterior do seu código. Isso proporciona uma experiência de fluxo de trabalho muito poderosa. A Windows Azure agora permite que você implante até 10 web-sites em um ambiente de hospedagem gratuito e compartilhado entre múltiplos usuários e bancos de dados (onde um site que você implantar será um dos vários sites rodando em um conjunto compartilhado de recursos do servidor). Isso te fornece uma maneira fácil para começar a desenvolver projetos sem nenhum custo envolvido. Você pode, opcionalmente, fazer o upgrade do seus sites para que os mesmos sejam executados em um "modo reservado" que os isola, de modo que você seja o único cliente dentro de uma máquina virtual: E você pode adaptar elasticamente a quantidade de recursos que os seus sites utilizam - o que te permite por exemplo aumentar a capacidade da sua instância reservada/particular de acordo com o aumento do seu tráfego: A Windows Azure controla automaticamente o balanceamento de carga do tráfego entre as instâncias das VMs, e você tem as mesmas opções de implantação super rápidas (FTP, Git, TFS e Web Deploy), independentemente de quantas instâncias reservadas você usar. Com a Windows Azure você paga por capacidade de processamento por hora - o que te permite dimensionar para cima e para baixo seus recursos para atender apenas o que você precisa. Serviços da Nuvem (Cloud Services) e Cache Distribuído (Distributed Caching) A Windows Azure também suporta a capacidade de construir serviços que rodam na nuvem que suportam ricas arquiteturas multicamadas, gerenciamento automatizado de aplicações, e que podem ser adaptados para implantações extremamente grandes. Anteriormente nós nos referíamos a esta capacidade como "serviços hospedados" - com o lançamento desta semana estamos agora rebatizando esta capacidade como "serviços da nuvem". Nós também estamos permitindo um monte de novos recursos com eles. Cache Distribuído Um dos novos recursos muito legais que estão sendo habilitados com os serviços da nuvem é uma nova capacidade de cache distribuído que te permite usar e configurar um cache distribuído de baixa latência, armazenado na memória (in-memory) dentro de suas aplicações. Esse cache é isolado para uso apenas por suas aplicações, e não possui limites de corte. Esse cache pode crescer e diminuir dinamicamente e elasticamente (sem que você tenha que reimplantar a sua aplicação ou fazer alterações no código), e suporta toda a riqueza da API do Servidor de Cache AppFabric (incluindo regiões, alta disponibilidade, notificações, cache local e muito mais). Além de suportar a API do Servidor de Cache AppFabric, esta nova capacidade de cache pode agora também suportar o protocolo Memcached - o que te permite apontar código escrito para o Memcached para o cache distribuído (sem que alterações de código sejam necessárias). O novo cache distribuído pode ser configurado para ser executado em uma de duas maneiras: 1) Utilizando uma abordagem de cache co-localizado (co-located). Nesta opção você aloca um percentual de memória dos seus roles web e worker existentes para que o mesmo seja usado ??pelo cache, e então o cache junta a memória em um grande cache distribuído. Qualquer dado colocado no cache por uma instância do role pode ser acessado por outras instâncias do role em sua aplicação - independentemente de os dados cacheados estarem armazenados neste ou em outro role. O grande benefício da opção de cache "co-localizado" é que ele é gratuito (você não precisa pagar nada para ativá-lo) e ele te permite usar o que poderia ser de outra forma memória não utilizada dentro das VMs da sua aplicação. 2) Alternativamente, você pode adicionar "cache worker roles" no seu serviço na nuvem que são utilizados unicamente para o cache. Estes também serão unidos em um grande anel de cache distribuído que outros roles dentro da sua aplicação podem acessar. Você pode usar esses roles para cachear dezenas ou centenas de GBs de dados na memória de forma extramente eficaz - e o cache pode ser aumentado ou diminuído elasticamente durante o tempo de execução dentro da sua aplicação: Novos SDKs e Ferramentas de Suporte Nós atualizamos todos os SDKs (kits para desenvolvimento de software) da Windows Azure com o lançamento de hoje para incluir novos recursos e capacidades. Nossos SDKs estão agora disponíveis em vários idiomas, e todo o código fonte deles está publicado sob uma licença Apache 2 e é mantido em repositórios no GitHub. O SDK .NET para Azure tem em particular um monte de grandes melhorias com o lançamento de hoje, e agora inclui suporte para ferramentas, tanto para o VS 2010 quanto para o VS 2012 RC. Estamos agora também entregando downloads do SDK para Windows, Mac e Linux nos idiomas que são oferecidos em todos esses sistemas - de modo a permitir que os desenvolvedores possam criar aplicações Windows Azure usando qualquer sistema operacional durante o desenvolvimento. Muito, Muito Mais O resumo acima é apenas uma pequena lista de algumas das melhorias que estão sendo entregues de uma forma preliminar ou definitiva hoje - há muito mais incluído no lançamento de hoje. Dentre estas melhorias posso citar novas capacidades para Virtual Private Networking (Redes Privadas Virtuais), novo runtime do Service Bus e respectivas ferramentas de suporte, o preview público dos novos Azure Media Services, novos Data Centers, upgrade significante para o hardware de armazenamento e rede, SQL Reporting Services, novos recursos de Identidade, suporte para mais de 40 novos países e territórios, e muito, muito mais. Você pode aprender mais sobre a Windows Azure e se cadastrar para experimentá-la gratuitamente em http://windowsazure.com. Você também pode assistir a uma apresentação ao vivo que estarei realizando às 1pm PDT (17:00Hs de Brasília), hoje 7 de Junho (hoje mais tarde), onde eu vou passar por todos os novos recursos. Estaremos abrindo as novas funcionalidades as quais me referi acima para uso público poucas horas após o término da apresentação. Nós estamos realmente animados para ver as grandes aplicações que você construirá com estes novos recursos. Espero que ajude, - Scott Texto traduzido do post original por Leniel Macaferi.

Read the article

Does Email Address Obfuscation Actually Prevent Spam?

- by Jason Fitzpatrick

Many people obfuscate their email addresses–typing out someguy (at) somedomain (dot) com, for example–to project themselves from SPAM bots. Do such obfuscation techniques actually work? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-drive grouping of Q&A web sites. HTG Explains: Does Your Android Phone Need an Antivirus? How To Use USB Drives With the Nexus 7 and Other Android Devices Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder?

Read the article

How to Make Your Computer Press a Key Every X Seconds

- by The Geek

Have you ever needed to press a key every couple of seconds, or every few minutes? Perhaps you’re playing a video game and you’re waiting for an item, or you’ve got some other reason. Either way, here’s how to make your PC do it automatically. You’ll need to start by downloading and installing AutoHotkey, which is a simple scripting language that allows you to create easy scripts. Once you do that, right-click anywhere and choose New –> AutoHotkey Script. Once you’ve done that, paste the following into the script: #PersistentSetTimer, PressTheKey, 1800000Return HTG Explains: How Hackers Take Over Web Sites with SQL Injection / DDoS Use Your Android Phone to Comparison Shop: 4 Scanner Apps Reviewed How to Run Android Apps on Your Desktop the Easy Way

Read the article

Diving into OpenStack Network Architecture - Part 1

- by Ronen Kofman

v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} rkofman Normal rkofman 83 3045 2014-05-23T21:11:00Z 2014-05-27T06:58:00Z 3 1883 10739 Oracle Corporation 89 25 12597 12.00 140 Clean Clean false false false false EN-US X-NONE HE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:Arial; mso-bidi-theme-font:minor-bidi; mso-bidi-language:AR-SA;} Before we begin OpenStack networking has very powerful capabilities but at the same time it is quite complicated. In this blog series we will review an existing OpenStack setup using the Oracle OpenStack Tech Preview and explain the different network components through use cases and examples. The goal is to show how the different pieces come together and provide a bigger picture view of the network architecture in OpenStack. This can be very helpful to users making their first steps in OpenStack or anyone wishes to understand how networking works in this environment. We will go through the basics first and build the examples as we go. According to the recent Icehouse user survey and the one before it, Neutron with Open vSwitch plug-in is the most widely used network setup both in production and in POCs (in terms of number of customers) and so in this blog series we will analyze this specific OpenStack networking setup. As we know there are many options to setup OpenStack networking and while Neturon + Open vSwitch is the most popular setup there is no claim that it is either best or the most efficient option. Neutron + Open vSwitch is an example, one which provides a good starting point for anyone interested in understanding OpenStack networking. Even if you are using different kind of network setup such as different Neutron plug-in or even not using Neutron at all this will still be a good starting point to understand the network architecture in OpenStack. The setup we are using for the examples is the one used in the Oracle OpenStack Tech Preview. Installing it is simple and it would be helpful to have it as reference. In this setup we use eth2 on all servers for VM network, all VM traffic will be flowing through this interface.The Oracle OpenStack Tech Preview is using VLANs for L2 isolation to provide tenant and network isolation. The following diagram shows how we have configured our deployment: This first post is a bit long and will focus on some basic concepts in OpenStack networking. The components we will be discussing are Open vSwitch, network namespaces, Linux bridge and veth pairs. Note that this is not meant to be a comprehensive review of these components, it is meant to describe the component as much as needed to understand OpenStack network architecture. All the components described here can be further explored using other resources. Open vSwitch (OVS) In the Oracle OpenStack Tech Preview OVS is used to connect virtual machines to the physical port (in our case eth2) as shown in the deployment diagram. OVS contains bridges and ports, the OVS bridges are different from the Linux bridge (controlled by the brctl command) which are also used in this setup. To get started let’s view the OVS structure, use the following command: # ovs-vsctl show 7ec51567-ab42-49e8-906d-b854309c9edf Bridge br-int Port br-int Interface br-int type: internal Port "int-br-eth2" Interface "int-br-eth2" Bridge "br-eth2" Port "br-eth2" Interface "br-eth2" type: internal Port "eth2" Interface "eth2" Port "phy-br-eth2" Interface "phy-br-eth2" ovs_version: "1.11.0" We see a standard post deployment OVS on a compute node with two bridges and several ports hanging off of each of them. The example above is a compute node without any VMs, we can see that the physical port eth2 is connected to a bridge called “br-eth2”. We also see two ports "int-br-eth2" and "phy-br-eth2" which are actually a veth pair and form virtual wire between the two bridges, veth pairs are discussed later in this post. When a virtual machine is created a port is created on one the br-int bridge and this port is eventually connected to the virtual machine (we will discuss the exact connectivity later in the series). Here is how OVS looks after a VM was launched: # ovs-vsctl show efd98c87-dc62-422d-8f73-a68c2a14e73d Bridge br-int Port "int-br-eth2" Interface "int-br-eth2" Port br-int Interface br-int type: internal Port "qvocb64ea96-9f" tag: 1 Interface "qvocb64ea96-9f" Bridge "br-eth2" Port "phy-br-eth2" Interface "phy-br-eth2" Port "br-eth2" Interface "br-eth2" type: internal Port "eth2" Interface "eth2" ovs_version: "1.11.0" Bridge "br-int" now has a new port "qvocb64ea96-9f" which connects to the VM and tagged with VLAN 1. Every VM which will be launched will add a port on the “br-int” bridge for every network interface the VM has. Another useful command on OVS is dump-flows for example: # ovs-ofctl dump-flows br-int NXST_FLOW reply (xid=0x4): cookie=0x0, duration=735.544s, table=0, n_packets=70, n_bytes=9976, idle_age=17, priority=3,in_port=1,dl_vlan=1000 actions=mod_vlan_vid:1,NORMAL cookie=0x0, duration=76679.786s, table=0, n_packets=0, n_bytes=0, idle_age=65534, hard_age=65534, priority=2,in_port=1 actions=drop cookie=0x0, duration=76681.36s, table=0, n_packets=68, n_bytes=7950, idle_age=17, hard_age=65534, priority=1 actions=NORMAL As we see the port which is connected to the VM has the VLAN tag 1. However the port on the VM network (eth2) will be using tag 1000. OVS is modifying the vlan as the packet flow from the VM to the physical interface. In OpenStack the Open vSwitch agent takes care of programming the flows in Open vSwitch so the users do not have to deal with this at all. If you wish to learn more about how to program the Open vSwitch you can read more about it at http://openvswitch.org looking at the documentation describing the ovs-ofctl command. Network Namespaces (netns) Network namespaces is a very cool Linux feature can be used for many purposes and is heavily used in OpenStack networking. Network namespaces are isolated containers which can hold a network configuration and is not seen from outside of the namespace. A network namespace can be used to encapsulate specific network functionality or provide a network service in isolation as well as simply help to organize a complicated network setup. Using the Oracle OpenStack Tech Preview we are using the latest Unbreakable Enterprise Kernel R3 (UEK3), this kernel provides a complete support for netns. Let's see how namespaces work through couple of examples to control network namespaces we use the ip netns command: Defining a new namespace: # ip netns add my-ns # ip netns list my-ns As mentioned the namespace is an isolated container, we can perform all the normal actions in the namespace context using the exec command for example running the ifconfig command: # ip netns exec my-ns ifconfig -a lo Link encap:Local Loopback LOOPBACK MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) We can run every command in the namespace context, this is especially useful for debug using tcpdump command, we can ping or ssh or define iptables all within the namespace. Connecting the namespace to the outside world: There are various ways to connect into a namespaces and between namespaces we will focus on how this is done in OpenStack. OpenStack uses a combination of Open vSwitch and network namespaces. OVS defines the interfaces and then we can add those interfaces to namespace. So first let's add a bridge to OVS: # ovs-vsctl add-br my-bridge Now let's add a port on the OVS and make it internal: # ovs-vsctl add-port my-bridge my-port # ovs-vsctl set Interface my-port type=internal And let's connect it into the namespace: # ip link set my-port netns my-ns Looking inside the namespace: # ip netns exec my-ns ifconfig -a lo Link encap:Local Loopback LOOPBACK MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) my-port Link encap:Ethernet HWaddr 22:04:45:E2:85:21 BROADCAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Now we can add more ports to the OVS bridge and connect it to other namespaces or other device like physical interfaces. Neutron is using network namespaces to implement network services such as DCHP, routing, gateway, firewall, load balance and more. In the next post we will go into this in further details. Linux Bridge and veth pairs Linux bridge is used to connect the port from OVS to the VM. Every port goes from the OVS bridge to a Linux bridge and from there to the VM. The reason for using regular Linux bridges is for security groups’ enforcement. Security groups are implemented using iptables and iptables can only be applied to Linux bridges and not to OVS bridges. Veth pairs are used extensively throughout the network setup in OpenStack and are also a good tool to debug a network problem. Veth pairs are simply a virtual wire and so veths always come in pairs. Typically one side of the veth pair will connect to a bridge and the other side to another bridge or simply left as a usable interface. In this example we will create some veth pairs, connect them to bridges and test connectivity. This example is using regular Linux server and not an OpenStack node: Creating a veth pair, note that we define names for both ends: # ip link add veth0 type veth peer name veth1 # ifconfig -a . . veth0 Link encap:Ethernet HWaddr 5E:2C:E6:03:D0:17 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth1 Link encap:Ethernet HWaddr E6:B6:E2:6D:42:B8 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) . . To make the example more meaningful this we will create the following setup: veth0 => veth1 => br-eth3 => eth3 ======> eth2 on another Linux server br-eth3 – a regular Linux bridge which will be connected to veth1 and eth3 eth3 – a physical interface with no IP on it, connected to a private network eth2 – a physical interface on the remote Linux box connected to the private network and configured with the IP of 50.50.50.1 Once we create the setup we will ping 50.50.50.1 (the remote IP) through veth0 to test that the connection is up: # brctl addbr br-eth3 # brctl addif br-eth3 eth3 # brctl addif br-eth3 veth1 # brctl show bridge name bridge id STP enabled interfaces br-eth3 8000.00505682e7f6 no eth3 veth1 # ifconfig veth0 50.50.50.50 # ping -I veth0 50.50.50.51 PING 50.50.50.51 (50.50.50.51) from 50.50.50.50 veth0: 56(84) bytes of data. 64 bytes from 50.50.50.51: icmp_seq=1 ttl=64 time=0.454 ms 64 bytes from 50.50.50.51: icmp_seq=2 ttl=64 time=0.298 ms When the naming is not as obvious as the previous example and we don't know who are the paired veth interfaces we can use the ethtool command to figure this out. The ethtool command returns an index we can look up using ip link command, for example: # ethtool -S veth1 NIC statistics: peer_ifindex: 12 # ip link . . 12: veth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 Summary That’s all for now, we quickly reviewed OVS, network namespaces, Linux bridges and veth pairs. These components are heavily used in the OpenStack network architecture we are exploring and understanding them well will be very useful when reviewing the different use cases. In the next post we will look at how the OpenStack network is laid out connecting the virtual machines to each other and to the external world. @RonenKofman

Read the article

No, iCloud Isn’t Backing Them All Up: How to Manage Photos on Your iPhone or iPad

- by Chris Hoffman

Are the photos you take with your iPhone or iPad backed up in case you lose your device? If you’re just relying on iCloud to manage your important memories, your photos may not be backed up at all. Apple’s iCloud has a photo-syncing feature in the form of “Photo Stream,” but Photo Stream doesn’t actually perform any long-term backups of your photos. iCloud’s Photo Backup Limitations Assuming you’ve set up iCloud on your iPhone or iPad, your device is using a feature called “Photo Stream” to automatically upload the photos you take to your iCloud storage and sync them across your devices. Unfortunately, there are some big limitations here. 1000 Photos: Photo Stream only backs up the latest 1000 photos. Do you have 1500 photos in your Camera Roll folder on your phone? If so, only the latest 1000 photos are stored in your iCloud account online. If you don’t have those photos backed up elsewhere, you’ll lose them when you lose your phone. If you have 1000 photos and take one more, the oldest photo will be removed from your iCloud Photo Stream. 30 Days: Apple also states that photos in your Photo Stream will be automatically deleted after 30 days “to give your devices plenty of time to connect and download them.” Some people report photos aren’t deleted after 30 days, but it’s clear you shouldn’t rely on iCloud for more than 30 days of storage. iCloud Storage Limits: Apple only gives you 5 GB of iCloud storage space for free, and this is shared between backups, documents, and all other iCloud data. This 5 GB can fill up pretty quickly. If your iCloud storage is full and you haven’t purchased any more storage more from Apple, your photos aren’t being backed up. Videos Aren’t Included: Photo Stream doesn’t include videos, so any videos you take aren’t automatically backed up. It’s clear that iCloud’s Photo Stream isn’t designed as a long-term way to store your photos, just a convenient way to access recent photos on all your devices before you back them up for real. iCloud’s Photo Stream is Designed for Desktop Backups If you have a Mac, you can launch iPhoto and enable the Automatic Import option under Photo Stream in its preferences pane. Assuming your Mac is on and connected to the Internet, iPhoto will automatically download photos from your photo stream and make local backups of them on your hard drive. You’ll then have to back up your photos manually so you don’t lose them if your Mac’s hard drive ever fails. If you have a Windows PC, you can install the iCloud Control Panel, which will create a Photo Stream folder on your PC. Your photos will be automatically downloaded to this folder and stored in it. You’ll want to back up your photos so you don’t lose them if your PC’s hard drive ever fails. Photo Stream is clearly designed to be used along with a desktop application. Photo Stream temporarily backs up your photos to iCloud so iPhoto or iCloud Control Panel can download them to your Mac or PC and make a local backup before they’re deleted. You could also use iTunes to sync your photos from your device to your PC or Mac, but we don’t really recommend it — you should never have to use iTunes. How to Actually Back Up All Your Photos Online So Photo Stream is actually pretty inconvenient — or, at least, it’s just a way to temporarily sync photos between your devices without storing them long-term. But what if you actually want to automatically back up your photos online without them being deleted automatically? The solution here is a third-party app that does this for you, offering the automatic photo uploads with long-term storage. There are several good services with apps in the App Store: Dropbox: Dropbox’s Camera Upload feature allows you to automatically upload the photos — and videos — you take to your Dropbox account. They’ll be easily accessible anywhere there’s a Dropbox app and you can get much more free Dropbox storage than you can iCloud storage. Dropbox will never automatically delete your old photos. Google+: Google+ offers photo and video backups with its Auto Upload feature, too. Photos will be stored in your Google+ Photos — formerly Picasa Web Albums — and will be marked as private by default so no one else can view them. Full-size photos will count against your free 15 GB of Google account storage space, but you can also choose to upload an unlimited amount of photos at a smaller resolution. Flickr: The Flickr app is no longer a mess. Flickr offers an Auto Upload feature for uploading full-size photos you take and free Flickr accounts offer a massive 1 TB of storage for you to store your photos. The massive amount of free storage alone makes Flickr worth a look. Use any of these services and you’ll get an online, automatic photo backup solution you can rely on. You’ll get a good chunk of free space, your photos will never be automatically deleted, and you can easily access them from any device. You won’t have to worry about storing local copies of your photos and backing them up manually. Apple should fix this mess and offer a better solution for long-term photo backup, especially considering the limitations aren’t immediately obvious to users. Until they do, third-party apps are ready to step in and take their place. You can also automatically back up your photos to the web on Android with Google+’s Auto Upload or Dropbox’s Camera Upload. Image Credit: Simon Yeo on Flickr

Read the article

Pyro Jam Can Is a DIY Mini Ruben’s Tube

- by Jason Fitzpatrick

Earlier this year we showed you how to make a full-size Ruben’s Tube; now make a tiny single-column fire speaker with the Pyro Jam Can. Instructables’ user Patrick needed a simple device to enter into an Instuctables contest centered on fire-themed projects. His contribution, seen in the video above, is a single-column Ruben’s Tube (for the unfamiliar, a Ruben’s Tube is a device through which sound and flammable gas are passed; the resulting flame is modulated by the frequency of the sound). If your next party wouldn’t be the same without a sound system that pumps bass beats and fire, you know where to get started. The Pyro Jam Can [via Hack A Day] Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone How To Migrate Windows 7 to a Solid State Drive Follow How-To Geek on Google+

Read the article

Developing web apps using ASP.NET MVC 3, Razor and EF Code First - Part 1

- by shiju

In this post, I will demonstrate web application development using ASP. NET MVC 3, Razor and EF code First. This post will also cover Dependency Injection using Unity 2.0 and generic Repository and Unit of Work for EF Code First. The following frameworks will be used for this step by step tutorial. ASP.NET MVC 3 EF Code First CTP 5 Unity 2.0 Define Domain Model Let’s create domain model for our simple web application Category class public class Category { public int CategoryId { get; set; } [Required(ErrorMessage = "Name Required")] [StringLength(25, ErrorMessage = "Must be less than 25 characters")] public string Name { get; set;} public string Description { get; set; } public virtual ICollection<Expense> Expenses { get; set; } } Expense class public class Expense { public int ExpenseId { get; set; } public string Transaction { get; set; } public DateTime Date { get; set; } public double Amount { get; set; } public int CategoryId { get; set; } public virtual Category Category { get; set; } } We have two domain entities - Category and Expense. A single category contains a list of expense transactions and every expense transaction should have a Category. In this post, we will be focusing on CRUD operations for the entity Category and will be working on the Expense entity with a View Model object in the later post. And the source code for this application will be refactored over time. The above entities are very simple POCO (Plain Old CLR Object) classes and the entity Category is decorated with validation attributes in the System.ComponentModel.DataAnnotations namespace. Now we want to use these entities for defining model objects for the Entity Framework 4. Using the Code First approach of Entity Framework, we can first define the entities by simply writing POCO classes without any coupling with any API or database library. This approach lets you focus on domain model which will enable Domain-Driven Development for applications. EF code first support is currently enabled with a separate API that is runs on top of the Entity Framework 4. EF Code First is reached CTP 5 when I am writing this article. Creating Context Class for Entity Framework We have created our domain model and let’s create a class in order to working with Entity Framework Code First. For this, you have to download EF Code First CTP 5 and add reference to the assembly EntitFramework.dll. You can also use NuGet to download add reference to EEF Code First. public class MyFinanceContext : DbContext { public MyFinanceContext() : base("MyFinance") { } public DbSet<Category> Categories { get; set; } public DbSet<Expense> Expenses { get; set; } } The above class MyFinanceContext is derived from DbContext that can connect your model classes to a database. The MyFinanceContext class is mapping our Category and Expense class into database tables Categories and Expenses using DbSet<TEntity> where TEntity is any POCO class. When we are running the application at first time, it will automatically create the database. EF code-first look for a connection string in web.config or app.config that has the same name as the dbcontext class. If it is not find any connection string with the convention, it will automatically create database in local SQL Express database by default and the name of the database will be same name as the dbcontext class. You can also define the name of database in constructor of the the dbcontext class. Unlike NHibernate, we don’t have to use any XML based mapping files or Fluent interface for mapping between our model and database. The model classes of Code First are working on the basis of conventions and we can also use a fluent API to refine our model. The convention for primary key is ‘Id’ or ‘<class name>Id’. If primary key properties are detected with type ‘int’, ‘long’ or ‘short’, they will automatically registered as identity columns in the database by default. Primary key detection is not case sensitive. We can define our model classes with validation attributes in the System.ComponentModel.DataAnnotations namespace and it automatically enforces validation rules when a model object is updated or saved. Generic Repository for EF Code First We have created model classes and dbcontext class. Now we have to create generic repository pattern for data persistence with EF code first. If you don’t know about the repository pattern, checkout Martin Fowler’s article on Repository Let’s create a generic repository to working with DbContext and DbSet generics. public interface IRepository<T> where T : class { void Add(T entity); void Delete(T entity); T GetById(long Id); IEnumerable<T> All(); } RepositoryBasse – Generic Repository class public abstract class RepositoryBase<T> where T : class { private MyFinanceContext database; private readonly IDbSet<T> dbset; protected RepositoryBase(IDatabaseFactory databaseFactory) { DatabaseFactory = databaseFactory; dbset = Database.Set<T>(); } protected IDatabaseFactory DatabaseFactory { get; private set; } protected MyFinanceContext Database { get { return database ?? (database = DatabaseFactory.Get()); } } public virtual void Add(T entity) { dbset.Add(entity); } public virtual void Delete(T entity) { dbset.Remove(entity); } public virtual T GetById(long id) { return dbset.Find(id); } public virtual IEnumerable<T> All() { return dbset.ToList(); } } DatabaseFactory class public class DatabaseFactory : Disposable, IDatabaseFactory { private MyFinanceContext database; public MyFinanceContext Get() { return database ?? (database = new MyFinanceContext()); } protected override void DisposeCore() { if (database != null) database.Dispose(); } } Unit of Work If you are new to Unit of Work pattern, checkout Fowler’s article on Unit of Work . According to Martin Fowler, the Unit of Work pattern "maintains a list of objects affected by a business transaction and coordinates the writing out of changes and the resolution of concurrency problems." Let’s create a class for handling Unit of Work public interface IUnitOfWork { void Commit(); } UniOfWork class public class UnitOfWork : IUnitOfWork { private readonly IDatabaseFactory databaseFactory; private MyFinanceContext dataContext; public UnitOfWork(IDatabaseFactory databaseFactory) { this.databaseFactory = databaseFactory; } protected MyFinanceContext DataContext { get { return dataContext ?? (dataContext = databaseFactory.Get()); } } public void Commit() { DataContext.Commit(); } } The Commit method of the UnitOfWork will call the commit method of MyFinanceContext class and it will execute the SaveChanges method of DbContext class. Repository class for Category In this post, we will be focusing on the persistence against Category entity and will working on other entities in later post. Let’s create a repository for handling CRUD operations for Category using derive from a generic Repository RepositoryBase<T>. public class CategoryRepository: RepositoryBase<Category>, ICategoryRepository { public CategoryRepository(IDatabaseFactory databaseFactory) : base(databaseFactory) { } } public interface ICategoryRepository : IRepository<Category> { } If we need additional methods than generic repository for the Category, we can define in the CategoryRepository. Dependency Injection using Unity 2.0 If you are new to Inversion of Control/ Dependency Injection or Unity, please have a look on my articles at http://weblogs.asp.net/shijuvarghese/archive/tags/IoC/default.aspx. I want to create a custom lifetime manager for Unity to store container in the current HttpContext. public class HttpContextLifetimeManager<T> : LifetimeManager, IDisposable { public override object GetValue() { return HttpContext.Current.Items[typeof(T).AssemblyQualifiedName]; } public override void RemoveValue() { HttpContext.Current.Items.Remove(typeof(T).AssemblyQualifiedName); } public override void SetValue(object newValue) { HttpContext.Current.Items[typeof(T).AssemblyQualifiedName] = newValue; } public void Dispose() { RemoveValue(); } } Let’s create controller factory for Unity in the ASP.NET MVC 3 application. public class UnityControllerFactory : DefaultControllerFactory { IUnityContainer container; public UnityControllerFactory(IUnityContainer container) { this.container = container; } protected override IController GetControllerInstance(RequestContext reqContext, Type controllerType) { IController controller; if (controllerType == null) throw new HttpException( 404, String.Format( "The controller for path '{0}' could not be found" + "or it does not implement IController.", reqContext.HttpContext.Request.Path)); if (!typeof(IController).IsAssignableFrom(controllerType)) throw new ArgumentException( string.Format( "Type requested is not a controller: {0}", controllerType.Name), "controllerType"); try { controller= container.Resolve(controllerType) as IController; } catch (Exception ex) { throw new InvalidOperationException(String.Format( "Error resolving controller {0}", controllerType.Name), ex); } return controller; } } Configure contract and concrete types in Unity Let’s configure our contract and concrete types in Unity for resolving our dependencies. private void ConfigureUnity() { //Create UnityContainer IUnityContainer container = new UnityContainer() .RegisterType<IDatabaseFactory, DatabaseFactory>(new HttpContextLifetimeManager<IDatabaseFactory>()) .RegisterType<IUnitOfWork, UnitOfWork>(new HttpContextLifetimeManager<IUnitOfWork>()) .RegisterType<ICategoryRepository, CategoryRepository>(new HttpContextLifetimeManager<ICategoryRepository>()); //Set container for Controller Factory ControllerBuilder.Current.SetControllerFactory( new UnityControllerFactory(container)); } In the above ConfigureUnity method, we are registering our types onto Unity container with custom lifetime manager HttpContextLifetimeManager. Let’s call ConfigureUnity method in the Global.asax.cs for set controller factory for Unity and configuring the types with Unity. protected void Application_Start() { AreaRegistration.RegisterAllAreas(); RegisterGlobalFilters(GlobalFilters.Filters); RegisterRoutes(RouteTable.Routes); ConfigureUnity(); } Developing web application using ASP.NET MVC 3 We have created our domain model for our web application and also have created repositories and configured dependencies with Unity container. Now we have to create controller classes and views for doing CRUD operations against the Category entity. Let’s create controller class for Category Category Controller public class CategoryController : Controller { private readonly ICategoryRepository categoryRepository; private readonly IUnitOfWork unitOfWork; public CategoryController(ICategoryRepository categoryRepository, IUnitOfWork unitOfWork) { this.categoryRepository = categoryRepository; this.unitOfWork = unitOfWork; } public ActionResult Index() { var categories = categoryRepository.All(); return View(categories); } [HttpGet] public ActionResult Edit(int id) { var category = categoryRepository.GetById(id); return View(category); } [HttpPost] public ActionResult Edit(int id, FormCollection collection) { var category = categoryRepository.GetById(id); if (TryUpdateModel(category)) { unitOfWork.Commit(); return RedirectToAction("Index"); } else return View(category); } [HttpGet] public ActionResult Create() { var category = new Category(); return View(category); } [HttpPost] public ActionResult Create(Category category) { if (!ModelState.IsValid) { return View("Create", category); } categoryRepository.Add(category); unitOfWork.Commit(); return RedirectToAction("Index"); } [HttpPost] public ActionResult Delete(int id) { var category = categoryRepository.GetById(id); categoryRepository.Delete(category); unitOfWork.Commit(); var categories = categoryRepository.All(); return PartialView("CategoryList", categories); } } Creating Views in Razor Now we are going to create views in Razor for our ASP.NET MVC 3 application. Let’s create a partial view CategoryList.cshtml for listing category information and providing link for Edit and Delete operations. CategoryList.cshtml @using MyFinance.Helpers; @using MyFinance.Domain; @model IEnumerable<Category> <table> <tr> <th>Actions</th> <th>Name</th> <th>Description</th> </tr> @foreach (var item in Model) { <tr> <td> @Html.ActionLink("Edit", "Edit",new { id = item.CategoryId }) @Ajax.ActionLink("Delete", "Delete", new { id = item.CategoryId }, new AjaxOptions { Confirm = "Delete Expense?", HttpMethod = "Post", UpdateTargetId = "divCategoryList" }) </td> <td> @item.Name </td> <td> @item.Description </td> </tr> } </table> <p> @Html.ActionLink("Create New", "Create") </p> The delete link is providing Ajax functionality using the Ajax.ActionLink. This will call an Ajax request for Delete action method in the CategoryCotroller class. In the Delete action method, it will return Partial View CategoryList after deleting the record. We are using CategoryList view for the Ajax functionality and also for Index view using for displaying list of category information. Let’s create Index view using partial view CategoryList Index.chtml @model IEnumerable<MyFinance.Domain.Category> @{ ViewBag.Title = "Index"; } <h2>Category List</h2> <script src="@Url.Content("~/Scripts/jquery.unobtrusive-ajax.min.js")" type="text/javascript"></script> <div id="divCategoryList"> @Html.Partial("CategoryList", Model) </div> We can call the partial views using Html.Partial helper method. Now we are going to create View pages for insert and update functionality for the Category. Both view pages are sharing common user interface for entering the category information. So I want to create an EditorTemplate for the Category information. We have to create the EditorTemplate with the same name of entity object so that we can refer it on view pages using @Html.EditorFor(model => model) . So let’s create template with name Category. Let’s create view page for insert Category information @model MyFinance.Domain.Category @{ ViewBag.Title = "Save"; } <h2>Create</h2> <script src="@Url.Content("~/Scripts/jquery.validate.min.js")" type="text/javascript"></script> <script src="@Url.Content("~/Scripts/jquery.validate.unobtrusive.min.js")" type="text/javascript"></script> @using (Html.BeginForm()) { @Html.ValidationSummary(true) <fieldset> <legend>Category</legend> @Html.EditorFor(model => model) <p> <input type="submit" value="Create" /> </p> </fieldset> } <div> @Html.ActionLink("Back to List", "Index") </div> ViewStart file In Razor views, we can add a file named _viewstart.cshtml in the views directory and this will be shared among the all views with in the Views directory. The below code in the _viewstart.cshtml, sets the Layout page for every Views in the Views folder. @{ Layout = "~/Views/Shared/_Layout.cshtml"; } Source Code You can download the source code from http://efmvc.codeplex.com/ . The source will be refactored on over time. Summary In this post, we have created a simple web application using ASP.NET MVC 3 and EF Code First. We have discussed on technologies and practices such as ASP.NET MVC 3, Razor, EF Code First, Unity 2, generic Repository and Unit of Work. In my later posts, I will modify the application and will be discussed on more things. Stay tuned to my blog for more posts on step by step application building.

Read the article

How can I sync with an iPod Nano 6G?

- by Martin

I'm having no luck at all with this iPod Nano. I've tried the following software: Banshee - The iPod shows up and files seem to be copied, but they don't show up on the iPod. Rhythmbox - Same as Banshee. Claims to sync but no files available on the iPod gPodder - At first it wouldn't even recognize the device even though I set the mount point and device type. After syncing one file to the iPod from iTunes on my mac it now behaves as Banshee and Rythmbox. gtkpod - Again: Copies the files but they are inacessible on the iPod. Hipo - Doesn't even recognize the iPod Amarok - What is this, I don't even... So to summarize: After some fiddling I can get most of these apps to recognize the iPod and copy files to it, but they are not accessible on the iPod which sort of defeats the whole purpose. Help me out here. My continued harmonic love life depends on it. (Yes, it's the girlfriends iPod and laptop)

Read the article

How to Setup Gmail for Custom Domains on the Kindle Fire’s Email App

- by The Geek

If you’ve just opened your shiny new Kindle Fire and tried to connect it to Gmail using your own custom (not @gmail.com) email address, you might be in for a surprise: the email account wizard has no idea how to handle this scenario, even if you pick Gmail at the beginning. Here’s how to fix it. Note: we’re in the middle of doing a thorough test of the Kindle Fire, and we’ll post our in-depth review in the next few days. So far: it’s a great tablet for the price. Use Your Android Phone to Comparison Shop: 4 Scanner Apps Reviewed How to Run Android Apps on Your Desktop the Easy Way HTG Explains: Do You Really Need to Defrag Your PC?

Read the article

Skype Video Calling Comes To iPhone And iPod Touch

- by Gopinath

Skype 3.0 app for iPhone/iPod Touch lets you make video calls right from your iOS device to another iOS device or computer running Skype application. Skype blog post says This season is very special as we are releasing a new version of Skype for iPhone and iPod Touch with video calling. Skype video calling is supported over WiFi and 3G* data connections. You can enjoy video calls with users on all Skype desktop versions and with other Skype for iPhone, iPod Touch, and iPad users. You can make video calls in both portrait and landscape mode and use both front and back cameras. Users on iPhone 4, 3GS and iPod Touch (4th Generation) can enjoy full 2-way video calling. Users with iPod Touch (3rd Generation) and iPads can receive video. Download the app straight from AppStore This article titled,Skype Video Calling Comes To iPhone And iPod Touch, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

Read the article

Ubuntu 12.04, Can hear the sound but Sound option in settings shows no sound card

- by Vivek Srivastava

I have weired issue. I did a fresh installation of Ubuntu 12.04. Then I installed Nvidia drives for my graphics card. I executed the command "modprobe nvidia" after installing the Nvidia drivers and rebooted. After reboot, sound indicator in top panel is disabled and I can't control the volume from there. I opened Settings Sound and it does not show any sound card installed. However, I can hear the sound. Please help. Output of lspci | grep Audio 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 01:00.1 Audio device: NVIDIA Corporation GF110 High Definition Audio Controller (rev a1) Output of lsmod | grep snd snd_hda_codec_hdmi 32191 4 snd_hda_codec_realtek 73851 1 snd_hda_intel 33367 0 snd_hda_codec 134156 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_timer 29990 1 snd_pcm snd 78855 7 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm

Read the article

Unlock the Full Value of Oracle CRM On Demand

- by charles.knapp

Register for this live Oracle CRM On Demand Virtual Community Session! Oracle CRM On Demand delivers the most complete On Demand CRM available anywhere. But how can you ensure you are getting maximum value from the many powerful features that Oracle CRM On Demand offers? Join our interactive Oracle CRM On Demand Virtual Community Session on Tuesday, January 11, 2011 from 10.00-11 a.m. PT / 1 p.m.-2 p.m. ET to get expert advice and discuss the best ways to unlock the full potential of Oracle CRM Demand with Mike Lairson, author of 'Oracle CRM On Demand Reporting'. Book OfferSend your Oracle CRM On Demand configuration ideas before the Webcast to [email protected] and you could win a free copy of 'Oracle CRM On Demand Reporting' by Mike Lairson. Learn more and register now!

Read the article

What You Said: What’s on Your Geeky Christmas List

- by Jason Fitzpatrick

Earlier this week we asked you to share what’s on your geeky Christmas list; you responded and we’re back to share your longed for tech goodies. The most requested item was this year’s hot introduction to the project board market: the Raspberry Pi. Dave writes: A Rapsberry Pi to tinker with, especially to see if I can get it up and running with OpenElec/Raspbmc and a torrent client for a low power media centre/htpc We just finished setting up a batch of new 512MB Raspberry Pi systems running the newest release of Rasbmbc and can’t recommend it enough–new refinements in Raspbmc and the extra 256MB of RAM really improve the media center experience. All John wants is a real keyboard so he can escape the torture of using a touch screen: How to Factory Reset Your Android Phone or Tablet When It Won’t Boot Our Geek Trivia App for Windows 8 is Now Available Everywhere How To Boot Your Android Phone or Tablet Into Safe Mode

Read the article

How can I get a Belkin N600 DB (F9L1101v1) to work on Ubuntu 12,04 64-Bit

- by rheide

I could use some assistance to trying to get a Belkin N600 DB Wireless Dual-Band USB Adapter to work on a Dell Inspiron 1525 with 64-Bit Ubuntu 12.04. The device won't work out of the box. Tried to go the NDISWrapper route, but using the GUI, received the following message: Module could not be loaded. Error was: FATAL: Module ndiswrapper not found. Is the ndiswrapper module installed? Despite the fact that it showed up listed in the GUI, the device still did not function properly. How should I proceed from here?

Read the article

Gnome Shell segfault in libglib-2.0

- by slohui

I have been using Ubuntu 11.10 + Gnome Shell with a Nvidia card, but now I've moved it to my new PC which has an ATI card, at first it wasn't booting but I installed the driver from amd.com and then it worked. Anyway my problem is that gnome-shell is crashing, mostly when I try to start a VirtualBox machine (it happened in other times but I don't remember what I was doing). Sometimes gnome-shell respawns and it continue working but sometimes it doesn't so I have to restart lightdm and lose all the windows I was using. Here's some of the syslog when the crash occurs: Apr 9 12:20:08 desktop-1 NetworkManager[1032]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/vboxnet0, iface: vboxnet0) Apr 9 12:20:08 desktop-1 NetworkManager[1032]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/vboxnet0, iface: vboxnet0): no ifupdown configuration found. Apr 9 12:20:08 desktop-1 NetworkManager[1032]: <warn> /sys/devices/virtual/net/vboxnet0: couldn't determine device driver; ignoring... Apr 9 12:20:08 desktop-1 kernel: [ 4498.689561] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use) Apr 9 12:24:29 desktop-1 gnome-session[1617]: WARNING: Application 'gnome-shell.desktop' killed by signal Apr 9 12:24:45 desktop-1 gnome-session[1617]: WARNING: App 'gnome-shell.desktop' respawning too quickly Apr 9 12:24:45 desktop-1 gnome-session[1617]: CRITICAL: We failed, but the fail whale is dead. Sorry.... Apr 9 12:25:20 desktop-1 kernel: [ 4810.769775] show_signal_msg: 30 callbacks suppressed |----- > Apr 9 12:25:20 desktop-1 kernel: [ 4810.769785] gnome-shell[3427]: segfault at b0 ip b6bd09cd sp bfc9b650 error 4 in libglib-2.0.so.0.3000.0[b6b71000+f7000]** Apr 9 12:25:20 desktop-1 gnome-session[1617]: WARNING: Application 'gnome-shell.desktop' killed by signal Apr 9 12:25:23 desktop-1 kernel: [ 4814.055705] EXT4-fs (sda1): Unaligned AIO/DIO on inode 133295 by VirtualBox; performance will be poor. Apr 9 12:26:55 desktop-1 gnome-session[1617]: Gdk-WARNING: gnome-session: Fatal IO error 11 (Resource temporarily unavailable) on X server :0.#012 Apr 9 12:26:55 desktop-1 kernel: [ 4905.373256] [fglrx] IRQ 56 Disabled Apr 9 12:26:59 desktop-1 acpid: client 1124[0:0] has disconnected Apr 9 12:26:59 desktop-1 acpid: client connected from 3864[0:0] Apr 9 12:26:59 desktop-1 acpid: 1 client rule loaded Apr 9 12:26:59 desktop-1 kernel: [ 4909.700095] fglrx_pci 0000:02:00.0: irq 56 for MSI/MSI-X Apr 9 12:26:59 desktop-1 kernel: [ 4909.701466] [fglrx] Firegl kernel thread PID: 3867 Apr 9 12:26:59 desktop-1 kernel: [ 4909.701625] [fglrx] Firegl kernel thread PID: 3868 Apr 9 12:26:59 desktop-1 kernel: [ 4909.701852] [fglrx] Firegl kernel thread PID: 3869 Apr 9 12:26:59 desktop-1 kernel: [ 4909.702021] [fglrx] IRQ 56 Enabled Apr 9 12:26:59 desktop-1 kernel: [ 4909.861815] [fglrx] Gart USWC size:1280 M. Apr 9 12:26:59 desktop-1 kernel: [ 4909.861817] [fglrx] Gart cacheable size:508 M. Apr 9 12:26:59 desktop-1 kernel: [ 4909.861820] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Apr 9 12:26:59 desktop-1 kernel: [ 4909.861821] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 Apr 9 12:26:59 desktop-1 kernel: [ 4909.861823] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 Does anyone could guide me on how to fix this? Or the proper place where to ask for help.

Read the article

How to sync with iPod Nano 6G?

- by Martin

I'm having no luck at all with this iPod Nano. I've tried the following software: Banshee - The iPod shows up and files seem to be copied, but they don't show up on the iPod. Rythmbox - Same as Banshee. Claims to sync but no files available on the iPod gPodder - At first it wouldn't even recognize the device even though I set the mount point and device type. After syncing one file to the iPod from iTunes on my mac it now behaves as Banshee and Rythmbox. gtkpod - Again: Copies the files but they are inacessible on the iPod. Hipo - Doesn't even recognize the iPod Amarok - What is this, I don't even... So to summarize: After some fiddling I can get most of these apps to recognize the iPod and copy files to it, but they are not accessible on the iPod which sort of defeats the whole purpose. Help me out here. My continued harmonic love life depends on it. (Yes, it's the girlfriends iPod and laptop)

Read the article

help with fixing fwts errors log

- by jasmines

Here is an extract of results.log: MTRR validation. Test 1 of 3: Validate the kernel MTRR IOMEM setup. FAILED [MEDIUM] MTRRIncorrectAttr: Test 1, Memory range 0xc0000000 to 0xdfffffff (PCI Bus 0000:00) has incorrect attribute Write-Combining. FAILED [MEDIUM] MTRRIncorrectAttr: Test 1, Memory range 0xfee01000 to 0xffffffff (PCI Bus 0000:00) has incorrect attribute Write-Protect. ==================================================================================================== Test 1 of 1: Kernel log error check. Kernel message: [ 0.208079] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored ADVICE: This is not exactly a failure mode but a warning from the kernel. The _OSI() method has implemented a match to the 'Linux' query in the DSDT and this is redundant because the ACPI driver matches onto the Windows _OSI strings by default. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 3.512783] ACPI Error : Method parse/execution failed [\_SB_.PCI0.GFX0._DOD] (Node f7425858), AE_AML_PACKAGE_LIMIT (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Found 1 unique errors in kernel log. ==================================================================================================== Check if system is using latest microcode. ---------------------------------------------------------------------------------------------------- Cannot read microcode file /usr/share/misc/intel-microcode.dat. Aborted test, initialisation failed. ==================================================================================================== MSR register tests. FAILED [MEDIUM] MSRCPUsInconsistent: Test 1, MSR SYSENTER_ESP (0x175) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0xffffffffffffffff). MSR CPU 0 -> 0xf7bb9c40 vs CPU 1 -> 0xf7bc7c40 FAILED [MEDIUM] MSRCPUsInconsistent: Test 1, MSR MISC_ENABLE (0x1a0) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0x400c51889). MSR CPU 0 -> 0x850088 vs CPU 1 -> 0x850089 ==================================================================================================== Checks firmware has set PCI Express MaxReadReq to a higher value on non-motherboard devices. ---------------------------------------------------------------------------------------------------- Test 1 of 1: Check firmware settings MaxReadReq for PCI Express devices. MaxReadReq for pci://00:00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) is low (128) [Audio device]. MaxReadReq for pci://00:02:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection is low (128) [Network controller]. FAILED [LOW] LowMaxReadReq: Test 1, 2 devices have low MaxReadReq settings. Firmware may have configured these too low. ADVICE: The MaxReadRequest size is set too low and will affect performance. It will provide excellent bus sharing at the cost of bus data transfer rates. Although not a critical issue, it may be worth considering setting the MaxReadRequest size to 256 or 512 to increase throughput on the PCI Express bus. Some drivers (for example the Brocade Fibre Channel driver) allow one to override the firmware settings. Where possible, this BIOS configuration setting is worth increasing it a little more for better performance at a small reduction of bus sharing. ==================================================================================================== PCIe ASPM check. ---------------------------------------------------------------------------------------------------- Test 1 of 2: PCIe ASPM ACPI test. PCIE ASPM is not controlled by Linux kernel. ADVICE: BIOS reports that Linux kernel should not modify ASPM settings that BIOS configured. It can be intentional because hardware vendors identified some capability bugs between the motherboard and the add-on cards. Test 2 of 2: PCIe ASPM registers test. WARNING: Test 2, RP 00h:1Ch.01h L0s not enabled. WARNING: Test 2, RP 00h:1Ch.01h L1 not enabled. WARNING: Test 2, Device 02h:00h.00h L0s not enabled. WARNING: Test 2, Device 02h:00h.00h L1 not enabled. PASSED: Test 2, PCIE aspm setting matched was matched. WARNING: Test 2, RP 00h:1Ch.05h L0s not enabled. WARNING: Test 2, RP 00h:1Ch.05h L1 not enabled. WARNING: Test 2, Device 85h:00h.00h L0s not enabled. WARNING: Test 2, Device 85h:00h.00h L1 not enabled. PASSED: Test 2, PCIE aspm setting matched was matched. ==================================================================================================== Extract and analyse Windows Management Instrumentation (WMI). Test 1 of 2: Check Windows Management Instrumentation in DSDT Found WMI Method WMAA with GUID: 5FB7F034-2C63-45E9-BE91-3D44E2C707E4, Instance 0x01 Found WMI Event, Notifier ID: 0x80, GUID: 95F24279-4D7B-4334-9387-ACCDC67EF61C, Instance 0x01 PASSED: Test 1, GUID 95F24279-4D7B-4334-9387-ACCDC67EF61C is handled by driver hp-wmi (Vendor: HP). Found WMI Event, Notifier ID: 0xa0, GUID: 2B814318-4BE8-4707-9D84-A190A859B5D0, Instance 0x01 FAILED [MEDIUM] WMIUnknownGUID: Test 1, GUID 2B814318-4BE8-4707-9D84-A190A859B5D0 is unknown to the kernel, a driver may need to be implemented for this GUID. ADVICE: A WMI driver probably needs to be written for this event. It can checked for using: wmi_has_guid("2B814318-4BE8-4707-9D84-A190A859B5D0"). One can install a notify handler using wmi_install_notify_handler("2B814318-4BE8-4707-9D84-A190A859B5D0", handler, NULL). http://lwn.net/Articles/391230 describes how to write an appropriate driver. Found WMI Object, Object ID AB, GUID: 05901221-D566-11D1-B2F0-00A0C9062910, Instance 0x01, Flags: 00 Found WMI Method WMBA with GUID: 1F4C91EB-DC5C-460B-951D-C7CB9B4B8D5E, Instance 0x01 Found WMI Object, Object ID BC, GUID: 2D114B49-2DFB-4130-B8FE-4A3C09E75133, Instance 0x7f, Flags: 00 Found WMI Object, Object ID BD, GUID: 988D08E3-68F4-4C35-AF3E-6A1B8106F83C, Instance 0x19, Flags: 00 Found WMI Object, Object ID BE, GUID: 14EA9746-CE1F-4098-A0E0-7045CB4DA745, Instance 0x01, Flags: 00 Found WMI Object, Object ID BF, GUID: 322F2028-0F84-4901-988E-015176049E2D, Instance 0x01, Flags: 00 Found WMI Object, Object ID BG, GUID: 8232DE3D-663D-4327-A8F4-E293ADB9BF05, Instance 0x01, Flags: 00 Found WMI Object, Object ID BH, GUID: 8F1F6436-9F42-42C8-BADC-0E9424F20C9A, Instance 0x00, Flags: 00 Found WMI Object, Object ID BI, GUID: 8F1F6435-9F42-42C8-BADC-0E9424F20C9A, Instance 0x00, Flags: 00 Found WMI Method WMAC with GUID: 7391A661-223A-47DB-A77A-7BE84C60822D, Instance 0x01 Found WMI Object, Object ID BJ, GUID: DF4E63B6-3BBC-4858-9737-C74F82F821F3, Instance 0x05, Flags: 00 ==================================================================================================== Disassemble DSDT to check for _OSI("Linux"). ---------------------------------------------------------------------------------------------------- Test 1 of 1: Disassemble DSDT to check for _OSI("Linux"). This is not strictly a failure mode, it just alerts one that this has been defined in the DSDT and probably should be avoided since the Linux ACPI driver matches onto the Windows _OSI strings { If (_OSI ("Linux")) { Store (0x03E8, OSYS) } If (_OSI ("Windows 2001")) { Store (0x07D1, OSYS) } If (_OSI ("Windows 2001 SP1")) { Store (0x07D1, OSYS) } If (_OSI ("Windows 2001 SP2")) { Store (0x07D2, OSYS) } If (_OSI ("Windows 2006")) { Store (0x07D6, OSYS) } If (LAnd (MPEN, LEqual (OSYS, 0x07D1))) { TRAP (0x01, 0x48) } TRAP (0x03, 0x35) } WARNING: Test 1, DSDT implements a deprecated _OSI("Linux") test. ==================================================================================================== 0 passed, 0 failed, 1 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== ACPI DSDT Method Semantic Tests. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP Failed to install global event handler. Test 22 of 93: Check _PSR (Power Source). ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 22, Detected an infinite loop when evaluating method '\_SB_.AC__._PSR'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 22, \_SB_.AC__._PSR correctly acquired and released locks 16 times. Test 35 of 93: Check _TMP (Thermal Zone Current Temp). ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 35, Detected an infinite loop when evaluating method '\_TZ_.DTSZ._TMP'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 35, \_TZ_.DTSZ._TMP correctly acquired and released locks 14 times. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 35, Detected an infinite loop when evaluating method '\_TZ_.CPUZ._TMP'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 35, \_TZ_.CPUZ._TMP correctly acquired and released locks 10 times. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 35, Detected an infinite loop when evaluating method '\_TZ_.SKNZ._TMP'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 35, \_TZ_.SKNZ._TMP correctly acquired and released locks 10 times. PASSED: Test 35, _TMP correctly returned sane looking value 0x00000b4c (289.2 degrees K) PASSED: Test 35, \_TZ_.BATZ._TMP correctly acquired and released locks 9 times. PASSED: Test 35, _TMP correctly returned sane looking value 0x00000aac (273.2 degrees K) PASSED: Test 35, \_TZ_.FDTZ._TMP correctly acquired and released locks 7 times. Test 46 of 93: Check _DIS (Disable). FAILED [MEDIUM] MethodShouldReturnNothing: Test 46, \_SB_.PCI0.LPCB.SIO_.COM1._DIS returned values, but was expected to return nothing. Object returned: INTEGER: 0x00000000 ADVICE: This probably won't cause any errors, but it should be fixed as the AML code is not conforming to the expected behaviour as described in the ACPI specification. FAILED [MEDIUM] MethodShouldReturnNothing: Test 46, \_SB_.PCI0.LPCB.SIO_.LPT0._DIS returned values, but was expected to return nothing. Object returned: INTEGER: 0x00000000 ADVICE: This probably won't cause any errors, but it should be fixed as the AML code is not conforming to the expected behaviour as described in the ACPI specification. Test 61 of 93: Check _WAK (System Wake). Test _WAK(1) System Wake, State S1. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(2) System Wake, State S2. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(3) System Wake, State S3. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(4) System Wake, State S4. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(5) System Wake, State S5. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test 87 of 93: Check _BCL (Query List of Brightness Control Levels Supported). Package has 2 elements: 00: INTEGER: 0x00000000 01: INTEGER: 0x00000000 FAILED [MEDIUM] Method_BCLElementCount: Test 87, Method _BCL should return a package of more than 2 integers, got just 2. Test 88 of 93: Check _BCM (Set Brightness Level). ACPICA Exception AE_AML_PACKAGE_LIMIT during execution of method _BCM FAILED [CRITICAL] AEAMLPackgeLimit: Test 88, Detected error 'Package limit' when evaluating '\_SB_.PCI0.GFX0.DD02._BCM'. ==================================================================================================== ACPI table settings sanity checks. ---------------------------------------------------------------------------------------------------- Test 1 of 1: Check ACPI tables. PASSED: Test 1, Table APIC passed. Table ECDT not present to check. FAILED [MEDIUM] FADT32And64BothDefined: Test 1, FADT 32 bit FIRMWARE_CONTROL is non-zero, and X_FIRMWARE_CONTROL is also non-zero. Section 5.2.9 of the ACPI specification states that if the FIRMWARE_CONTROL is non-zero then X_FIRMWARE_CONTROL must be set to zero. ADVICE: The FADT FIRMWARE_CTRL is a 32 bit pointer that points to the physical memory address of the Firmware ACPI Control Structure (FACS). There is also an extended 64 bit version of this, the X_FIRMWARE_CTRL pointer that also can point to the FACS. Section 5.2.9 of the ACPI specification states that if the X_FIRMWARE_CTRL field contains a non zero value then the FIRMWARE_CTRL field *must* be zero. This error is also detected by the Linux kernel. If FIRMWARE_CTRL and X_FIRMWARE_CTRL are defined, then the kernel just uses the 64 bit version of the pointer. PASSED: Test 1, Table HPET passed. PASSED: Test 1, Table MCFG passed. PASSED: Test 1, Table RSDT passed. PASSED: Test 1, Table RSDP passed. Table SBST not present to check. PASSED: Test 1, Table XSDT passed. ==================================================================================================== Re-assemble DSDT and find syntax errors and warnings. ---------------------------------------------------------------------------------------------------- Test 1 of 2: Disassemble and reassemble DSDT FAILED [HIGH] AMLAssemblerError4043: Test 1, Assembler error in line 2261 Line | AML source ---------------------------------------------------------------------------------------------------- 02258| 0x00000000, // Range Minimum 02259| 0xFEDFFFFF, // Range Maximum 02260| 0x00000000, // Translation Offset 02261| 0x00000000, // Length | ^ | error 4043: Invalid combination of Length and Min/Max fixed flags 02262| ,, _Y0E, AddressRangeMemory, TypeStatic) 02263| DWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, Cacheable, ReadWrite, 02264| 0x00000000, // Granularity ==================================================================================================== ADVICE: (for error #4043): This occurs if the length is zero and just one of the resource MIF/MAF flags are set, or the length is non-zero and resource MIF/MAF flags are both set. These are illegal combinations and need to be fixed. See section 6.4.3.5 Address Space Resource Descriptors of version 4.0a of the ACPI specification for more details. FAILED [HIGH] AMLAssemblerError4050: Test 1, Assembler error in line 2268 Line | AML source ---------------------------------------------------------------------------------------------------- 02265| 0xFEE01000, // Range Minimum 02266| 0xFFFFFFFF, // Range Maximum 02267| 0x00000000, // Translation Offset 02268| 0x011FEFFF, // Length | ^ | error 4050: Length is not equal to fixed Min/Max window 02269| ,, , AddressRangeMemory, TypeStatic) 02270| }) 02271| Method (_CRS, 0, Serialized) ==================================================================================================== ADVICE: (for error #4050): The minimum address is greater than the maximum address. This is illegal. FAILED [HIGH] AMLAssemblerError1104: Test 1, Assembler error in line 8885 Line | AML source ---------------------------------------------------------------------------------------------------- 08882| Method (_DIS, 0, NotSerialized) 08883| { 08884| DSOD (0x02) 08885| Return (0x00) | ^ | warning level 0 1104: Reserved method should not return a value (_DIS) 08886| } 08887| 08888| Method (_SRS, 1, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 1, Assembler error in line 9195 Line | AML source ---------------------------------------------------------------------------------------------------- 09192| Method (_DIS, 0, NotSerialized) 09193| { 09194| DSOD (0x01) 09195| Return (0x00) | ^ | warning level 0 1104: Reserved method should not return a value (_DIS) 09196| } 09197| 09198| Method (_SRS, 1, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1127: Test 1, Assembler error in line 9242 Line | AML source ---------------------------------------------------------------------------------------------------- 09239| CreateWordField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y21._MAX, MAX2) 09240| CreateByteField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y21._LEN, LEN2) 09241| CreateWordField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y22._INT, IRQ0) 09242| CreateWordField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y23._DMA, DMA0) | ^ | warning level 0 1127: ResourceTag smaller than Field (Tag: 8 bits, Field: 16 bits) 09243| If (RLPD) 09244| { 09245| Store (0x00, Local0) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1128: Test 1, Assembler error in line 18682 Line | AML source ---------------------------------------------------------------------------------------------------- 18679| Store (0x01, Index (DerefOf (Index (Local0, 0x02)), 0x01)) 18680| If (And (WDPE, 0x40)) 18681| { 18682| Wait (\_SB.BEVT, 0x10) | ^ | warning level 0 1128: Result is not used, possible operator timeout will be missed 18683| } 18684| 18685| Store (BRID, Index (DerefOf (Index (Local0, 0x02)), 0x02)) ==================================================================================================== ADVICE: (for warning level 0 #1128): The operation can possibly timeout, and hence the return value indicates an timeout error. However, because the return value is not checked this very probably indicates that the code is buggy. A possible scenario is that a mutex times out and the code attempts to access data in a critical region when it should not. This will lead to undefined behaviour. This should be fixed. Table DSDT (0) reassembly: Found 2 errors, 4 warnings. Test 2 of 2: Disassemble and reassemble SSDT PASSED: Test 2, SSDT (0) reassembly, Found 0 errors, 0 warnings. FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 60 Line | AML source ---------------------------------------------------------------------------------------------------- 00057| { 00058| Store (CPDC (Arg0), Local0) 00059| GCAP (Local0) 00060| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00061| } 00062| 00063| Method (_OSC, 4, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 174 Line | AML source ---------------------------------------------------------------------------------------------------- 00171| { 00172| Store (\_PR.CPU0.CPDC (Arg0), Local0) 00173| GCAP (Local0) 00174| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00175| } 00176| 00177| Method (_OSC, 4, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 244 Line | AML source ---------------------------------------------------------------------------------------------------- 00241| { 00242| Store (\_PR.CPU0.CPDC (Arg0), Local0) 00243| GCAP (Local0) 00244| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00245| } 00246| 00247| Method (_OSC, 4, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 290 Line | AML source ---------------------------------------------------------------------------------------------------- 00287| { 00288| Store (\_PR.CPU0.CPDC (Arg0), Local0) 00289| GCAP (Local0) 00290| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00291| } 00292| 00293| Method (_OSC, 4, NotSerialized) ==================================================================================================== Table SSDT (1) reassembly: Found 0 errors, 4 warnings. PASSED: Test 2, SSDT (2) reassembly, Found 0 errors, 0 warnings. PASSED: Test 2, SSDT (3) reassembly, Found 0 errors, 0 warnings. ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== Critical failures: 1 method test, at 1 log line: 1449: Detected error 'Package limit' when evaluating '\_SB_.PCI0.GFX0.DD02._BCM'. High failures: 11 klog test, at 1 log line: 121: HIGH Kernel message: [ 3.512783] ACPI Error: Method parse/execution failed [\_SB_.PCI0.GFX0._DOD] (Node f7425858), AE_AML_PACKAGE_LIMIT (20110623/psparse-536) syntaxcheck test, at 1 log line: 1668: Assembler error in line 2261 syntaxcheck test, at 1 log line: 1687: Assembler error in line 2268 syntaxcheck test, at 1 log line: 1703: Assembler error in line 8885 syntaxcheck test, at 1 log line: 1716: Assembler error in line 9195 syntaxcheck test, at 1 log line: 1729: Assembler error in line 9242 syntaxcheck test, at 1 log line: 1742: Assembler error in line 18682 syntaxcheck test, at 1 log line: 1766: Assembler error in line 60 syntaxcheck test, at 1 log line: 1779: Assembler error in line 174 syntaxcheck test, at 1 log line: 1792: Assembler error in line 244 syntaxcheck test, at 1 log line: 1805: Assembler error in line 290 Medium failures: 9 mtrr test, at 1 log line: 76: Memory range 0xc0000000 to 0xdfffffff (PCI Bus 0000:00) has incorrect attribute Write-Combining. mtrr test, at 1 log line: 78: Memory range 0xfee01000 to 0xffffffff (PCI Bus 0000:00) has incorrect attribute Write-Protect. msr test, at 1 log line: 165: MSR SYSENTER_ESP (0x175) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0xffffffffffffffff). msr test, at 1 log line: 173: MSR MISC_ENABLE (0x1a0) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0x400c51889). wmi test, at 1 log line: 528: GUID 2B814318-4BE8-4707-9D84-A190A859B5D0 is unknown to the kernel, a driver may need to be implemented for this GUID. method test, at 1 log line: 1002: \_SB_.PCI0.LPCB.SIO_.COM1._DIS returned values, but was expected to return nothing. method test, at 1 log line: 1011: \_SB_.PCI0.LPCB.SIO_.LPT0._DIS returned values, but was expected to return nothing. method test, at 1 log line: 1443: Method _BCL should return a package of more than 2 integers, got just 2. acpitables test, at 1 log line: 1643: FADT 32 bit FIRMWARE_CONTROL is non-zero, and X_FIRMWARE_CONTROL is also non-zero. Se

Read the article

Clustering Basics and Challenges

- by Karoly Vegh

For upcoming posts it seemed to be a good idea to dedicate some time for cluster basic concepts and theory. This post misses a lot of details that would explode the articlesize, should you have questions, do not hesitate to ask them in the comments. The goal here is to get some concepts straight. I can't promise to give you an overall complete definitions of cluster, cluster agent, quorum, voting, fencing, split brain condition, so the following is more of an explanation. Here we go. -------- Cluster, HA, failover, switchover, scalability -------- An attempted definition of a Cluster: A cluster is a set (2+) server nodes dedicated to keep application services alive, communicating through the cluster software/framework with eachother, test and probe health status of servernodes/services and with quorum based decisions and with switchover/failover techniques keep the application services running on them available. That is, should a node that runs a service unexpectedly lose functionality/connection, the other ones would take over the and run the services, so that availability is guaranteed. To provide availability while strictly sticking to a consistent clusterconfiguration is the main goal of a cluster. At this point we have to add that this defines a HA-cluster, a High-Availability cluster, where the clusternodes are planned to run the services in an active-standby, or failover fashion. An example could be a single instance database. Some applications can be run in a distributed or scalable fashion. In the latter case instances of the application run actively on separate clusternodes serving servicerequests simultaneously. An example for this version could be a webserver that forwards connection requests to many backend servers in a round-robin way. Or a database running in active-active RAC setup. -------- Cluster arhitecture, interconnect, topologies -------- Now, what is a cluster made of? Servers, right. These servers (the clusternodes) need to communicate. This of course happens over the network, usually over dedicated network interfaces interconnecting all the clusternodes. These connection are called interconnects.How many clusternodes are in a cluster? There are different cluster topologies. The most simple one is a clustered pair topology, involving only two clusternodes: There are several more topologies, clicking the image above will take you to the relevant documentation. Also, to answer the question Solaris Cluster allows you to run up to 16 servers in a cluster. Where shall these clusternodes be placed? A very important question. The right answer is: It depends on what you plan to achieve with the cluster. Do you plan to avoid only a server outage? Then you can place them right next to eachother in the datacenter. Do you need to avoid DataCenter outage? In that case of course you should place them at least in different fire zones. Or in two geographically distant DataCenters to avoid disasters like floods, large-scale fires or power outages. We call this a stretched- or campus cluster, the clusternodes being several kilometers away from eachother. To cover really large distances, you probably need to move to a GeoCluster, which is a different kind of animal. What is a geocluster? A Geographic Cluster in Solaris Cluster terms is actually a metacluster between two, separate (locally-HA) clusters. -------- Cluster resource types, agents, resources, resource groups -------- So how does the cluster manage my applications? The cluster needs to start, stop and probe your applications. If you application runs, the cluster needs to check regularly if the application state is healthy, does it respond over the network, does it have all the processes running, etc. This is called probing. If the cluster deems the application is in a faulty state, then it can try to restart it locally or decide to switch (stop on node A, start on node B) the service. Starting, stopping and probing are the three actions that a cluster agent does. There are many different kinds of agents included in Solaris Cluster, but you can build your own too. Examples are an agent that manages (mounts, moves) ZFS filesystems, or the Oracle DB HA agent that cares about the database, or an agent that moves a floating IP address between nodes. There are lots of other agents included for Apache, Tomcat, MySQL, Oracle DB, Oracle Weblogic, Zones, LDoms, NFS, DNS, etc.We also need to clarify the difference between a cluster resource and the cluster resource group.A cluster resource is something that is managed by a cluster agent. Cluster resource types are included in Solaris cluster (see above, e.g. HAStoragePlus, HA-Oracle, LogicalHost). You can group cluster resources into cluster resourcegroups, and switch these groups together from one node to another. To stick to the example above, to move an Oracle DB service from one node to another, you have to switch the group between nodes, and the agents of the cluster resources in the group will do the following: On node A Shut down the DB Unconfigure the LogicalHost IP the DB Listener listens on unmount the filesystem Then, on node B: mount the FS configure the IP startup the DB -------- Voting, Quorum, Split Brain Condition, Fencing, Amnesia -------- How do the clusternodes agree upon their action? How do they decide which node runs what services? Another important question. Running a cluster is a strictly democratic thing.Every node has votes, and you need the majority of votes to have the deciding power. Now, this is usually no problem, clusternodes think very much all alike. Still, every action needs to be governed upon in a productive system, and has to be agreed upon. Agreeing is easy as long as the clusternodes all behave and talk to eachother over the interconnect. But if the interconnect is gone/down, this all gets tricky and confusing. Clusternodes think like this: "My job is to run these services. The other node does not answer my interconnect communication, it must be down. I'd better take control and run the services!". The problem is, as I have already mentioned, clusternodes very much think alike. If the interconnect is gone, they all assume the other node is down, and they all want to mount the data backend, enable the IP and run the database. Double IPs, double mounts, double DB instances - now that is trouble. Also, in a 2-node cluster they both have only 50% of the votes, that is, they themselves alone are not allowed to run a cluster. This is where you need a quorum device. According to Wikipedia, the "requirement for a quorum is protection against totally unrepresentative action in the name of the body by an unduly small number of persons.". They need additional votes to run the cluster. For this requirement a 2-node cluster needs a quorum device or a quorum server. If the interconnect is gone, (this is what we call a split brain condition) both nodes start to race and try to reserve the quorum device to themselves. They do this, because the quorum device bears an additional vote, that could ensure majority (50% +1). The one that manages to lock the quorum device (e.g. if it's an FC LUN, it SCSI reserves it) wins the right to build/run a cluster, the other one - realizing he was late - panics/reboots to ensure the cluster config stays consistent. Losing the interconnect isn't only endangering the availability of services, but it also endangers the cluster configuration consistence. Just imagine node A being down and during that the cluster configuration changes. Now node B goes down, and node A comes up. It isn't uptodate about the cluster configuration's changes so it will refuse to start a cluster, since that would lead to cluster amnesia, that is the cluster had some changes, but now runs with an older cluster configuration repository state, that is it's like it forgot about the changes. Also, to ensure application data consistence, the clusternode that wins the race makes sure that a server that isn't part of or can't currently join the cluster can access the devices. This procedure is called fencing. This usually happens to storage LUNs via SCSI reservation. Now, another important question: Where do I place the quorum disk? Imagine having two sites, two separate datacenters, one in the north of the city and the other one in the south part of it. You run a stretched cluster in the clustered pair topology. Where do you place the quorum disk/server? If you put it into the north DC, and that gets hit by a meteor, you lose one clusternode, which isn't a problem, but you also lose your quorum, and the south clusternode can't keep the cluster running lacking the votes. This problem can't be solved with two sites and a campus cluster. You will need a third site to either place the quorum server to, or a third clusternode. Otherwise, lacking majority, if you lose the site that had your quorum, you lose the cluster. Okay, we covered the very basics. We haven't talked about virtualization support, CCR, ClusterFilesystems, DID devices, affinities, storage-replication, management tools, upgrade procedures - should those be interesting for you, let me know in the comments, along with any other questions. Given enough demand I'd be glad to write a followup post too. Now I really want to move on to the second part in the series: ClusterInstallation. Oh, as for additional source of information, I recommend the documentation: http://docs.oracle.com/cd/E23623_01/index.html, and the OTN Oracle Solaris Cluster site: http://www.oracle.com/technetwork/server-storage/solaris-cluster/index.html

Search Results

Search found 29619 results on 1185 pages for 'android virtual device'.

Page 632/1185 | < Previous Page | 628 629 630 631 632 633 634 635 636 637 638 639 | Next Page >

- by retrac1324

- by SQLOS Team

- by Asian Angel

- by terrencebarr

- by Stephen.Walther

- by Lori Kaufman

- by Devendra

- by Leniel Macaferi

- by Jason Fitzpatrick

- by The Geek

- by Ronen Kofman

- by Chris Hoffman

- by Jason Fitzpatrick

- by shiju

- by Martin

- by The Geek

- by Gopinath

- by Vivek Srivastava

- by charles.knapp

- by Jason Fitzpatrick

- by rheide

- by slohui

- by Martin

- by jasmines

- by Karoly Vegh

< Previous Page | 628 629 630 631 632 633 634 635 636 637 638 639 | Next Page >