Search Results

Search found 19134 results on 766 pages for 'support contract'.

Page 640/766 | < Previous Page | 636 637 638 639 640 641 642 643 644 645 646 647  | Next Page >

  • HAProxy crashes on all requests in 1.5-dev12

    - by Daniel Hough
    I'm having an issue where HAProxy is crashing with no explanation when I switch from 1.4.12 to 1.5-dev12. The reason I'm switching is for the SSL offloading. My config file doesn't have any errors, it's quite simple and it works well with 1.4 - but for some reason when I run it with 1.5-dev12 I see the logs noting that the two backends I have have been set up, and then when I hit one of the frontends, I get an HTTP 400 in the browser and suddenly HAProxy isn't running anymore when I check. I understand that a common workaround to the lack of SSL support for HAProxy is to use Stud, and I may go with that since I am in need of an SSL solution for my service, but before I dele into that world I thought I might see if anybody has experienced the same problems and might know how to fix it. The server is Ubuntu 10.04 and I followed the make instructions on the Exceliance blog here. EDIT: On the advice of Kyle Brandt, I did a bit more investigation. I attached gdb to the haproxy process and when the crash occurred this is what I got: Program received signal SIGSEGV, Segmentation fault. 0x0804e5c2 in dequeue_all_listeners (list=0x9e1a418) at src/protocols.c:184 184 list_for_each_entry_safe(listener, l_back, list, wait_queue) { P.S. HAProxy is awesome, so thank you Exceliance for providing us with something so useful :)

    Read the article

  • Write once, read many (WORM) using Linux file system

    - by phil_ayres
    I have a requirement to write files to a Linux file system that can not be subsequently overwritten, appended to, updated in any way, or deleted. Not by a sudo-er, root, or anybody. I am attempting to meet the requirements of the financial services regulations for recordkeeping, FINRA 17A-4, which basically requires that electronic documents are written to WORM (write once, read many) devices. I would very much like to avoid having to use DVDs or expensive EMC Centera devices. Is there a Linux file system, or can SELinux support the requirement for files to be made complete immutable immediately (or at least soon) after write? Or is anybody aware of a way I could enforce this on an existing file system using Linux permissions, etc? I understand that I can set readonly permissions, and the immutable attribute. But of course I expect that a root user would be able to unset those. I considered storing data to small volumes that are unmounted and then remounted read-only, but then I think that root could still unmount and remount as writable again. I'm looking for any smart ideas, and worst case scenario I'm willing to do a little coding to 'enhance' an existing file system to provide this. Assuming there is a file system that is a good starting point. And put in place a carefully configured Linux server to act as this type of network storage device, doing nothing else. After all of that, encryption on the files would be useful too!

    Read the article

  • Shoretel Upgrade Path

    - by Brian
    I currently have a Shoretel Server running Server 2003 x32 as a virtual machine paired with a ShoreGear 90 switch and another unused switch of the same model being reserved for manual failover. I am getting the software mailed to me from my partner, but with limited support since the server is in a relatively remote area. I am tempted to upgrade the OS at the same time as performing the upgrade, but want to know if there are any horror stories or advice I should know about before diving in. I'm upgrading from Shoretel 9.2 Build. I will be upgrading first to version 10.1 then finally to 11.1. The system has been bullet proof since it was installed and we are upgrading mainly to get a client that is a little more modern. My question boils down to: Should I even bother with an OS upgrade or even possibly a fresh install of Windows with an install of Shoretel 11.1 and just transfer the configuration? Should I just stay with Server 2003 since it is supported in my target version of Shoretel and the upgrade will be more than enough to keep me busy as a novice?

    Read the article

  • What games work well on MacBook Pro (i7/GeForce GT 330M) within VMWare Fusion?

    - by webworm
    I have a 15" MacBook Pro (2.66 i7 with 8 GB RAM) with the GeForce GT 330M 512 MB graphics card. I use it primarily for development (Mac/Web/Windows) though I would like to play the occasional game with my son who uses a desktop PC system at home. I prefer to use VMWare Fusion for virtualization rather than BootCamp for a number of reasons. Heat/Fan issues with i7 under BootCamp Prefer to retain virtual machine as single file rather than dedicated partition (easier to move a nd backup) I have heard that Windows support of the GeForce GT 330 in BootCamp is not all that good. So that being said I was wondering what sort of games I would be able to play within the Fusion environment running Windows 7. I have 8 GB RAM and usually dedicate 4 GB to the virtual machine. I don't expect to be able to play the latest FPS games such as BattleField: Bad Company 2 or Call of Duty, rather I am looking at games such a Total War II, Civilizations IV, Supreme Commander, and other RTS type games. I should mention the native screen resolution of my MacBook Pro is 1680x1050, which is what I would be most likely running the VM at (fullscreen). Thank you for any advice.

    Read the article

  • RAID-capable 3.5" SATA Drives

    - by nroam
    I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

    Read the article

  • Nokia E75 Mail for Exchange

    - by Sebastian
    Hi, I have a SBS2003 runing Exchange Server 2003 SP2. My OWA has a godaddy certificate valid for 3 years to come installed. HTTPS works fine for OWA. The certificate has also been copied into the Nokia E95 I am trying to syncronize my Nokia E75 via Mail for Exchange to my mail account on the Exchange server. These are the steps i use: Menu Email New Start Select Internet Gateway Than i enter the details: [email protected] I select company email Mail for Exchange In the domain menu i enter : mydomain In the username/password menu i enter : myusername/mypassword In the server menu i enter : mail.mydomain.com (where the DNS resolves into the server's IP address) In the secure access i select : Internet / Secure / 443 NOTE : port 443 has been opened on my SBOX and forwarded to the exchange server. On IIS default website properties directory security secure communications edit the "Require Secure Channel SSL" is enabled. However, when i try to sync my phone i get the following error code: * Mail for Exch permissions illegal. Check permission configuration. * The phone log gives the following information : Username or Password Illegal. Correct Username and/or Password in the profile options. I've tried speaking with the Phone service support but they cannot identify the problem. Any help will be much apreciated.

    Read the article

  • Why does apache httpd tell me that my name-based virtualhosts only works with SNI enabled browers (RFC 4366)

    - by Arlukin
    Why does apache give me this error message in my logs? Is it a false positive? [warn] Init: Name-based SSL virtual hosts only work for clients with TLS server name indication support (RFC 4366) I have recently upgraded from Centos 5.7 to 6.3, and by that to a newer httpd version. I have always made my ssl virtualhost configurations like below. Where all domains that share the same certificate (mostly/always wildcard certs) share the same ip. But never got this error message before (or have I, maybe I haven't looked to enough in my logs?) From what I have learned this should work without SNI (Server Name Indication) Here is relevant parts of my httpd.conf file. Without this VirtualHost I don't get the error message. NameVirtualHost 10.101.0.135:443 <VirtualHost 10.101.0.135:443> ServerName sub1.domain.com SSLEngine on SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!aNull:!EDH:!DH:!ADH:!eNull:!LOW:!EXP:RC4+RSA+SHA1:+HIGH:+MEDIUM SSLCertificateFile /opt/RootLive/etc/ssl/ssl.crt/wild.fareoffice.com.crt SSLCertificateKeyFile /opt/RootLive/etc/ssl/ssl.key/wild.fareoffice.com.key SSLCertificateChainFile /opt/RootLive/etc/ssl/ca/geotrust-ca.pem </VirtualHost> <VirtualHost 10.101.0.135:443> ServerName sub2.domain.com SSLEngine on SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!aNull:!EDH:!DH:!ADH:!eNull:!LOW:!EXP:RC4+RSA+SHA1:+HIGH:+MEDIUM SSLCertificateFile /opt/RootLive/etc/ssl/ssl.crt/wild.fareoffice.com.crt SSLCertificateKeyFile /opt/RootLive/etc/ssl/ssl.key/wild.fareoffice.com.key SSLCertificateChainFile /opt/RootLive/etc/ssl/ca/geotrust-ca.pem </VirtualHost>

    Read the article

  • How to fix GMail time stamps in Outlook?

    - by SWB
    One of my email accounts is hosted at an ISP with unreliable IMAP support, and I can't change it. Fortunately, I have my personal email set up on Google Apps for Domains, so I created another GMail account there and turned on GMail's features that allow me to send and receive mail through the ISP account using GMail ("Send mail as" and "Get mail from other accounts" in GMail settings on the Accounts tab). I'm now using Outlook to retreive mail from the GMail account through IMAP, which in turn is retreiving mail from the ISP account through POP3. This basically works great, except for one very significant issue: Prior to setting this up, I already had several months of mail in the ISP account that I had been accessing via IMAP. GMail grabbed all of this mail via POP3 at, let's say, noon on April 5. In GMail's web interface (and on my iPod touch, and in Mozilla Thunderbird), all is well: the messages are all shown with their original time stamps. But when Outlook downloads these messages from GMail via IMAP, the time stamps are all set to noon on April 5 (the time GMail downloaded them from the ISP via POP3). That's not good, especially since we're talking about hundreds of messages here over a time span of several months. How can I fix this and get Outlook to display the original time stamps?

    Read the article

  • Reliable router with good VPN and WAN Throughput [closed]

    - by Asdande
    I have 2 cisco rv180 VPN router. These routers are giving me lots of problems. The webpages wont load correctly, slow response to load webpages plus other many issues. I have several cases pending with cisco. I give up on these routers. I would like to know if you guys can recommend me a reliable router for our 3 branches (NY - main, SC and FL). In NY- main office, we have 55 users. In SC branch, 6 users. In Florida we only have 1 (will grow soon). I need a router capable of support: 3 VPNs Site-to-Site connection VPN throughput of at least 40-50 Mbps WAN throughput at least 100 Mpbs and up PPTP Server for at least 5 PPTP users Web filtering - all users need access to internet Good Firewall Port forwarding for FTP Server - able to show the public IPs of FTP users (rv180 cannot do that, just shows me router's LAN interface IP, opened a case with cisco, now escaleted to level 2, still no answer or workaround) Dual WAN ports for balance or backup internet. Gigabit WAN/LAN ports Price between $400-$500 range. I was thinking on the TP-LINK TL-ER6120 or TL-ER6020 according to the review on smallnetbuilder.com http://www.smallnetbuilder.com/lanwan/lanwan-reviews/31983-tp-link-tl-er6020-safestream-gigabit-dual-wan-vpn-router-reviewed but I don't want to make another mistake as I did when I bought the cisco RV180. Thank you in advance,

    Read the article

  • Dual Boot Installing Ubuntu 12.04 with Windows 7 (64) on a non UEFI system fails

    - by Randnum
    I cannot seem to install the correct boot loader for a non-UEFI firmware system. I'm trying to install Ubuntu 12.04 and Windows 7 (64) which are technically compatible with GPT but for windows only if the firmware is UEFI enabled. My system uses the old BIOS system and does not support UEFI. Therefore, whenever I finish my Ubuntu install and try to install Windows I get a "cannot install to GPT partition type" error. Even if I use Gparted to format a special NTFS file format for windows it can't handle the GPT partition style because it doesn't have UEFI. But my ubuntu install always forces GPT during installation and never asks if I want to install the old BIOS style MBR instead. How do I resolve this? Both OS's will install fine on their own the problem is when I try to install the second OS it doesn't recognize any of the other's partitions and tries to rewrite it's own on top of the other. I've tried both OS's first and always run into the same problem. Since there is no way to make Windows recognize GPT without upgrading my Motherboard how do I tell Ubuntu to use the old BIOS MBR on install? Do I have to download a special Ubuntu with a specific grub version? or should I manaually configure my partition somehow to force it not to use GPT? Thank you,

    Read the article

  • Offloading backups to secondary network

    - by user1467163
    I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

    Read the article

  • Difficulty restoring a differential backup in SQL Server, 2 media families are expected or no files are ready for rollforward

    - by digiguru
    I have sql backups copied from server A to server B on a nightly basis. We want to move the sql server from server A to server B without much downtime, but the files are very large. I assumed that performing a differential backup and restore would solve the problem with the databases. Copy full backup from server A to copy to server B (10+gb) Open SQL Server Managment Studio on server B Right mouse on databases Restore Database Type in the new DB-name Choose "From Device" and browse to the backup file Click Okay. This is now resorting the original "full" backup. Test new db with dev application - everything works :) On original database rightmouse on DB Tasks Backup... Backup Type = Differential, Backup to disk, add a new file, and remove the old one (it needs to be a small file to transfer for the smallest amount of outage) Copy the diff backup onto the new db Right mouse on DB Tasks Restore Database This is where I get stuck. If I add both the new differential file, and the original backup to the restore process I get an error The media loaded on "M:\path\to\backup\full.bak" is formatted to support 1 media families, but 2 media families are expected according to the backup device specification. RESTORE HEADERONLY is terminating abnormally. But if I try to restore using just the differential file I get System.Data.SqlClient.SqlError: The log or differential backup cannot be restored because no files are ready to rollforward. (Microsoft.SqlServer.Smo) Any idea how to do it? Is there a better way of restoring backups with limited downtime?

    Read the article

  • S.M.A.R.T. broken sectors

    - by Jeffrey Vandenborne
    Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

    Read the article

  • How do I lower the hardware volume? (volume too high)

    - by Zom-B
    I have a 4yo Dell laptop with Windows XP Pro (modern ones unfortunately don't have a physical volume knob), and lately I'm using my Apple earphones, because they have much better low frequency response than my $10 earphones. They also have the side effect of being much louder. To give an indication of my agony, for most tasks (movie, music, games) I have my main volume at 3 ticks: drag to 0 with the mouse and press the up key 3 times (the handle does not even raise 1 pixel) and my wave volume at 50%. I notice that when I do this, I have a lot of digital noise, because I'm using just a tiny fraction of the 16-bit space. If I drag the Wave slider down until I barely hear the audio, it becomes really distorted and noisy, indicating that this is digital volume (in the DirectSound driver or something) and not hardware volume. I experimented in Audition. When I make a tone of 1000Hz at -50db, (all windows volumes at max) the volume is just below my pain threshold. When I zoom in to see how high the sample values reach, I see that just 8 of the 16 bits are used (about -100 ~ 100). When I generate such tone at -80db (minimum I can specify) then I can still clearly hear the tone, although really noisy. When I zoom in, I see that just 3 out of 16 bits are used. I created a squarewave tone that is just 1 bit high, and I can still hear it! For most uses, this is not a big problem (audiophiles will disagree!), as I just have more noise than usual (about the same as old 8 bit hardware), but I'm also in the process of programming a hearing test program, in which case this problem is a death blow as the test subjects will even hear tones at the bottom of the theoretical range (lowering the windows volume is futile, see above) (I cannot update drivers, as Dell has discontinued XP support for my model)

    Read the article

  • 404 not found error for virtual host

    - by qubit
    Hello, In my /etc/apache2/sites-enabled, i have a file site2.com.conf, which defines a virtual host as follows : <VirtualHost *:80> ServerAdmin hostmaster@wharfage ServerName site2.com ServerAlias www.site2.com site2.com DirectoryIndex index.html index.htm index.php DocumentRoot /var/www LogLevel debug ErrorLog /var/log/apache2/site2_error.log CustomLog /var/log/apache2/site2_access.log combined ServerSignature Off <Location /> Options -Indexes </Location> Alias /favicon.ico /srv/site2/static/favicon.ico Alias /static /srv/site2/static # Alias /media /usr/local/lib/python2.5/site-packages/django/contrib/admin/media Alias /admin/media /var/lib/python-support/python2.5/django/contrib/admin/media WSGIScriptAlias / /srv/site2/wsgi/django.wsgi WSGIDaemonProcess site2 user=samj group=samj processes=1 threads=10 WSGIProcessGroup site2 </VirtualHost> I do the following to enable the site : 1) In /etc/apache2/sites-enabled, i run the command a2ensite site2.com.conf 2) I then get a message site successfully enabled, and then i run the command /etc/init.d/apache2 reload. But, if i navigate to www.site2.com, i get 404 not found. I do have an index.html in /var/www (permissions:777 and ownership www-data:www-data), and i have also verified that a symlink was created for site2.com.conf in /etc/apache2/sites-enabled. Any way to fix this ? Thank you.

    Read the article

  • Servers/Websites Keep Going Down

    - by Tyler Johnson
    Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps Type: Linux

    Read the article

  • Windows 2008 Server can't connect to FTP

    - by stivlo
    I have Windows 2008 Server R2, and I am trying to install FTP services. My problem is I can't connect from outside, FileZilla complains with: Error: Connection timed out Error: Could not connect to server Here is what I did. With the Server Manager, I've installed the Roles FTP Server, FTP Service and FTP Extensibility. In Internet Information Services version 7.5, I've chosen Add FTP Site, enabled Basic Authentication, Allow a user to connect Read and Write. In FTP Firewall support on the main server, just after start page, I've set Data Channel Port Range to 49100-49250 and set the external IP Address as the one I see from outside. If I click on FTP IPv4 Address and Domain Restrictions, and click on Edit Feature Settings, I see that access for unspecified clients is set to Allow, so I click OK without changing those defaults. In FTP SSL Policy, I've set to Require SSL connection, certificate is self signed. I tried to connect with FileZilla from the same host and it works, however it doesn't work remotely, as I said above. I've enabled pfirewall.log, but apparently nothing gets logged. The server is in Amazon EC2, and on the security group inbound firewall rules, I've set that ports 21 and ports 49100-49250 accepts connections from everywhere. What else should I be checking to solve the problem?

    Read the article

  • Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

    - by Maxim Z.
    I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

    Read the article

  • Whats the best cloud backup solution for a small scale server environment?

    - by nbv4
    I have a server that runs a postgres database that contains about 200MB of data. Currently I have a cron job setup on my home computer which: ssh's into my server runs a remote script which makes a backup of the database scp's that dump over to my local hard drive for storage. Each dump is 20MiB. does this every six hours (one months of backups is roughly 2GiB) The problem with this setup is that if my local machine goes down for whatever reason, no backups will be made. Also, I can't have the cron run from the server, because I can't have it scp'd to my local machine from my server (firewalls and all that crap). My local machine is running Ubuntu 10.04, and my server is Ubuntu 9.10 server edition. I looked into Ubuntu One, but currently it's gui-only. I also looked into dropbox, but it's a pain in the ass to get setup in linux without gui support. Amazon S3 looks good but it's not free (yet dirt cheap). Is there any other alternative that I should look into? I'd prefer something where I can just have my script dump the database into a directory, and have the backup service 'watch' that folder and sync accordingly. I can maybe also have my local machine sync to the cloud backup so I have even more redundancy, plus easy access to my backups for use in testing. Edit: My server is a VPS, so what solution I end up using has to be 100% software based.

    Read the article

  • Deploying multiple identical copies of a virtual machine for compute tasks

    - by Reid
    I have a compute task which has a large number of library dependencies. I would like to deploy it on some of my company's large Linux clusters, where I do not have root. I could probably track down, compile, and install the right versions of all the libraries, but this looks to be quite tedious and would have to be repeated if I deployed it again somewhere else. On the other hand, it's pretty easy to install on current Ubuntu. This led me to wonder about a virtual machine approach. Could I put together a virtual machine which booted up, ran the computation (with parameters from and results to the host), and then shut down? In other words, I'd like a command like this that I could run on the host: $ ./run-vm --ram N --task /path/on/host/foo.sh --results /another/host/dir/ This would boot the VM, run foo.sh, and put the (relatively small) results of the computation in /another/host/dir/. It's important to start up many instances of the VM simultaneously, both on a single node and multiple nodes of the cluster. So it would be nice if I didn't have to make many copies of the VM virtual disk and metadata. As the task instances are completely independent, the VMs would not need any network support once deployed, or any outside communications beyond reading and writing the host filesystem. Is this possible, and if so, how might I go about doing it? Are there assumptions I've made above which are bogus?

    Read the article

  • iCloud backup merges or overwrites?

    - by Joe McMahon
    The following happened today (it was six AM my time, so yeah, I was dumb and dropped stitches in this process): A friend had a problem with her iPhone and needed to reset it. Unfortunately she did the reset while connected to iTunes and the restore process kicked in. In my sleepy state, I told her to go ahead. She did, and restored the most recent local (iTunes) backup (from July last year - she doesn't back up often, as she has an Air which is pretty full). During setup on the phone, she was prompted to merge data with the iCloud copy, and did so. There was no "restore from iCloud" prompt. Obviously I should have made sure she was disconnected from iTunes before she did the reset, or had her set it up as a new device and then restored from iCloud, but water under the bridge now. (Side question: could I have had her disconnect and then restart the phone again and avoid this whole process?) The question is: was the "merge" that happened in this process a true merge, or a replace? Her passwords for Mail were wrong, since they were the old ones from the old backup. If she does the wipe data and restore from iCloud, will she get her old SMSes and calendar entries back? Or did the merge decide that the phone, despite it being "old" was right and therefore the SMSes, calendar entries, etc. were discarded? As a recovery option, I have a 4-day-old iTunes backup here from ~/Library/Application Support/MobileSync/Backup, but she and the phone are 3000 miles away, and it's 8GB, so I can't easily restore it for her. I do have the option of encrypting it and mailing it on a data stick if the iCloud backup is now toast. Should she try the wipe and restore from the cloud (after backing up locally), or should I just get the more-recent backup in the mail? My goal is to get everything (especially the SMSes) back to the most recent version possible.

    Read the article

  • Ubuntu IP Configuration - multiple subnets & interfaces

    - by HaydnWVN
    Have a 'new' mailserver running postfix on Ubuntu. We are having some problems configuring the subnets & interfaces. Basically 2 subnets (.253. & .254.) need to be connected through the 3rd subnet (.252.) where the Router is residing. # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.62.254.199 netmask 255.255.0.0 network 10.62.254.0 broadcast 10.62.255.255 #gateway 10.62.252.138 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 10.62.252.138 dns-search ***.com auto eth1 iface eth1 inet static address 10.62.253.199 netmask 255.255.0.0 network 10.62.253.0 broadcast 10.62.255.255 #gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-nameservers 10.62.252.138 dns-search ***.com auto eth2 iface eth2 inet static address 10.62.252.199 netmask 255.255.0.0 network 10.62.252.0 broadcast 10.62.255.255 gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-search ***.com I have an external support company who are looking into this (they built and configured this server), but it's taking far too long... So I'm looking to highlight the mistake!

    Read the article

  • Recommendations for good Unix MTA / groupware solutions? [closed]

    - by Jez
    Possible Duplicate: Exchange server replacement that runs on Linux I'm setting up a Debian server, and one of the things I need on it is an MTA. I don't want to use something like Exim or Postfix because I want something that ties in SMTP, POP3, and IMAP all in one (a la Microsoft Exchange). Most MTAs also seem to be hellishly difficult to configure. Try and read the Exim documentation; you could do a university degree on it (I'm not kidding). When you can get an HTTP server like Cherokee which is easy to configure and has a nice web interface, do MTAs or groupware solutions need to be that hard? I'm aware that some people think "the Unix way" is to have lots of different interacting pieces of software (like maybe an SMTP MTA, POP3 service, webmail service, and overarching manager to tie them all together), but I think this is a situation where that just makes things a lot harder to deal with and one large software suite fits in much more nicely. So, I'm looking for good open source software suites that will run on Debian that: Combine (at least) SMTP, POP3, and IMAP Are easy(ish) to configure Have a nice configuration web interface or GUI Are not defunct projects I don't mind if it's groupware and offers calendaring too, but I would only be using the e-mail functionality for now. Another nice-to-have would be built-in webmail (if we're combining a bunch of functionality, why not?) Note however that I do NOT need Outlook support. I am not really looking for an "Exchange replacement drop-in". The suites I've found so far that seem to match the above criteria (and have appropriate licenses) are Citadel, Kolab, and Zimbra. I'd appreciate anyone who has experience with any of these giving me the pros and cons of them, such as how easy they are to configure and what their performance is like. I'd also appreciate any other suggestions for solutions that fulfil my criteria that I may have missed out.

    Read the article

  • How to improve Samba performance on VirtualBox machine?

    - by ColinM
    I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

    Read the article

  • Serious 64-bit laptop

    - by Daniel Gehriger
    For the past couple of years, I have been using an IBM Thinkpad T60p for daily work (software development, desktop & embedded). I am extremely satisfied with this machine, due to its robustness. It also has a few features I depend on: a high resolution display: 15.0" TFT FlexView display with 1600x1200 (UXGA); excellent keyboard; decent graphics and CPU performance. Some of the software I develop benefits from larger amounts of RAM, and 3GB (Windows 7 32-bit) or 4GB (Windows 7 64-bit on T60p) are no longer sufficient. My customers run desktop computers with 20GB and more, and I need to have at least 8GB to at least be able to run reasonable test cases. So I'm shopping around for a new laptop, but I'm struggling to find anything that matches my requirements: must run Windows 7 64-bit Pro or higher; must support at least 8GB of RAM (more is better) high screen resolution! While I prefer 4:3 I can live with wide screen. But I really hope to find something with a vertical screen resolution similar to what I have now... portable, so < 16" but = 14" I realize that FlexView isn't available anymore, but I'd like to avoid a glossy screen if possible. decent (not more) graphics performance, ideally hybrid (I'm doing a lot of CAD, never games). good keyboard reasonable CPU -- but I'm still fine with my current Core 2 Duo, so that shouldn't be too complicated. The T60p fits all those requirements, except the 8GB of RAM. Can you help me find a current notebook that would match most of them? I don't mind changing brand. Thanks!

    Read the article

< Previous Page | 636 637 638 639 640 641 642 643 644 645 646 647  | Next Page >