Search Results

Search found 28747 results on 1150 pages for 'switch case'.

Page 656/1150 | < Previous Page | 652 653 654 655 656 657 658 659 660 661 662 663  | Next Page >

• Bandwidth Suggestion

  - by Campo

  I have been asked to analyze the bandwidth usage of a company and make a recommendation for upgrading their Internet connection(s). Here is the layout 3 DLS lines so it is 3x(6 Down, 1 Up Each) into a load balancer out to the office's network. 30 VOIP phones run on a T1 (1.5 Down, 1.5 Up) The users at the company are heavily uploading. It is my suspicion that the issue in slowdown is being cause by multiple people uploading and others not being able to get requests out for even simple http requests. My initial idea is to get them a fiber line with a 10 down and 10 up. What do others think on this plan? Will that be enough to host their network traffic? What do I do about the VOIP line afterward? The fiber is expensive and I know the T1 does a great job for their VOIP so I do not want to suggest a DSL line because I know it may not be sufficient. I would also like to save them some money if I can. Maybe even get a faster fiber line and forgo the T1. Though I know their load balance/switch can only handle 20MB/S throughput. Looking for some confirmation/suggestions on my plan. I am planning on going in to get some real diagnostic numbers. Any suggestions on software to use for that? Preferably Windows software.

  Read the article

• Juniper’s Network Connect ncsvc on Linux: “host checker failed, error 10”

  - by hfs

  I’m trying to log in to a Juniper VPN with Network Connect from a headless Linux client. I followed the instructions and used the script from http://mad-scientist.us/juniper.html. When running the script with --nogui switch the command that gets finally executed is $HOME/.juniper_networks/network_connect/ncsvc -h HOST -u USER -r REALM -f $HOME/.vpn.default.crt. I get asked for the password, a line “Connecting to…” is printed but then the programm silently stops. When adding -L 5 (most verbose logging) to the command line, these are the last messages printed to the log: dsclient.info state: kStateCacheCleaner (dsclient.cpp:280) dsclient.info --> POST /dana-na/cc/ccupdate.cgi (authenticate.cpp:162) http_connection.para Entering state_start_connection (http_connection.cpp:282) http_connection.para Entering state_continue_connection (http_connection.cpp:299) http_connection.para Entering state_ssl_connect (http_connection.cpp:468) dsssl.para SSL connect ssl=0x833e568/sd=4 connection using cipher RC4-MD5 (DSSSLSock.cpp:656) http_connection.para Returning DSHTTP_COMPLETE from state_ssl_connect (http_connection.cpp:476) DSHttp.debug state_reading_response_body - copying 0 buffered bytes (http_requester.cpp:800) DSHttp.debug state_reading_response_body - recv'd 0 bytes data (http_requester.cpp:833) dsclient.info <-- 200 (authenticate.cpp:194) dsclient.error state host checker failed, error 10 (dsclient.cpp:282) ncapp.error Failed to authenticate with IVE. Error 10 (ncsvc.cpp:197) dsncuiapi.para DsNcUiApi::~DsNcUiApi (dsncuiapi.cpp:72) What does host checker failed mean? How can I find out what it tried to check and what failed? The HostChecker Configuration Guide mentions that a $HOME/.juniper_networks/tncc.jar gets installed on Linux, but my installation contains no such file. From that I concluded that HostChecker is disabled for my VPN on Linux? Are the POST to /dana-na/cc/ccupdate.cgi and “host checker failed” connected or independent? By running the connection over a SSL proxy I found out that the POST data is status=NOTOK (Funny side note: the client of the oh-so-secure VPN does not validate the server’s SSL certificate, so is wide open to MITM attacks…). So it seems that it’s the client that closes the connection and not the server.

  Read the article

• stdout, stderr, and what else? (going insane parsing slapadd output)

  - by user64204

  I am using slapadd to restore a backup. That backup contains 45k entries which takes a while to restore so I need to get some progress update from slapadd. Luckily for me there is the -v switch which gives an output similar to this one: added: "[email protected],ou=People,dc=example,dc=org" (00003d53) added: "[email protected],ou=People,dc=example,dc=org" (00003d54) added: "[email protected],ou=People,dc=example,dc=org" (00003d55) .######## 44.22% eta 05m05s elapsed 04m spd 29.2 k/s added: "[email protected],ou=People,dc=example,dc=org" (00003d56) added: "[email protected],ou=People,dc=example,dc=org" (00003d57) added: "[email protected],ou=People,dc=example,dc=org" (00003d58) added: "[email protected],ou=People,dc=example,dc=org" (00003d59) Every N entries added, slapadd writes a progress update output line (.######## 44.22% eta 05m05s elapsed ...) which I want to keep and an output line for every entry created which I want to hide because it exposes people's email address but still want to count them to know how many users were imported The way I thought about hiding emails and showing the progress update is this: $ slapadd -v ... 2>&1 | tee log.txt | grep '########' # => would give me real-time progress update $ grep "added" log.txt | wc -l # => once backup has been restored I would know how many users were added I tried different variations of the above, and whatever I try I can't grep the progress update output line. I traced slapadd as follows: sudo strace slapadd -v ... And here is what I get: write(2, "added: \"[email protected]"..., 78added: "[email protected],ou=People,dc=example,dc=org" (00000009) ) = 78 gettimeofday({1322645227, 253338}, NULL) = 0 _######## 44.22% eta 05m05s elapsed 04m spd 29.2 k/s ) = 80 write(2, "\n", 1 ) As you can see, the percentage line isn't sent to either stdout or stderr (FYI I have validated with known working and failing commands that 2 is stderr and 1 is stdout) Q1: Where is the progress update output line going? Q2: How can I grep on it while sending stderr to a file? Additional info: I'm running Openldap 2.4.21 on ubuntu server 10.04

  Read the article

• Monitor goes black for a few seconds

  - by privatehuff

  I have a Hanns G 28" monitor, Model # HG281D It has its issues (viewing angle sucks) but has been functional and solid, great for desktop stuff. Worked without any sign of any problems for 6-12 months. However, now the monitor "goes black" for about 2-3 seconds, almost like when you click "detect display" It does not turn off (power light does not go amber) The computer is completely unaffected and the video mode never changes when the picture returns. The computer is fully responsive and will keep playing music or taking my keypresses during the time I can't see anything. (it just happened and I kept typing, etc) It happens on multiple computers across several operating systems. (I have an 8-port iogear KVM switch that has several computers connected) But, it seems to happen only on certain computers. I have a hackintosh that does it, a windows 7 PC that does not, a lenovo laptop that does not, and my old ubuntu 8.10 box did not do it, but my new mint 8 box does do it. I've check the connections and tried changing out the power cable and the vga cable. Sometimes it won't happen for hours (or days) and sometimes it happens several times per hour. It was happening many months ago, did not happen for months, and has now started happening again. Does this make any sense? What could it be?

  Read the article

• Provisioning DELL servers using only linux tools

  - by Krist van Besien

  We have taken delivery of a bunch off Dell Poweredge Rack servers. Unfortunately when ordering it was neglegted to ask for dhcp to be enabled in the built in iDRAC controlers... So they are all stuck on the same IP address. Which means that I'll have to go to each of them individually and configure a new IP in the console... In the future I want to avoid that. Now Dell proposes to deliver the next batch with auto discovery enabled. As I understand this means that when the machine wakes up for the first time the iDRAC will request a DHCP address. The DHCP server then supposedly also provides a "provisioning" server, that provides it with a username and password, and a configuration to be applied. This would allow us to for example configure things like RAID automatically. However, I can't seem to find a way to set up such a provisioning server that does not involve setting up a windows machine. I want to use Linux tools exclusively. Is there a way to do this? I want to just rack servers, switch them on, and then do everything remotely. And that using only linux tools?

  Read the article

• Autologin 2 Windows users OR Login another user from the desktop

  - by fpdragon

  I'm using two windows users on my HTPC at the same time. One is just for watching videos and one for administration via remote. This setup is quite ideal for me since windows can handle multiple concurrent logins and the win "rdp concurrent hack" (Google). The problem is, I want both users to be logged in automatically when the pc was started. It shall be possible to watch tv and also the admin user shall be automatically logged in to start my scripts and other tasks, even if I haven't logged in via remote desktop manually. Later, when I want to admin my htpc I can just rdp connect the admin user without interrupting the video playback on the actual HTPC's screen and check my cleanup tasks, downloads, ... witch already executed for this admin user. But right now I found no solution to automatically login user A from a user B desktop and I also found no solution to autologin both users immediately at startup. As a workaround I have to fire up my other notebook machine and login one time with the remote user via rdp. From this time on the remote admin user is running concurrent with the main user in the background of the machine. The other workaround would be... after startup switch user from main user to admin user and then back again. But that also requires manual steps. I'm on a Windows 8 System right now but all infos for Win7 or XP would be also interesting. thanks a lot for all ideas. PS: just to prevent useless posts... don't tell me that only one user can be logged in to windows. ;)

  Read the article

• Share Firefox/Thnderbird data between W7 and Linux Mint 12 in dual boot computer

  - by Albert

  I've just set up my laptop (where I had running only W7) with a dual boot to run Linux Mint 12 as well. I have a "Data" partition (apart from the required partitions for W7 and Linux) where I store pretty much everything that isn't software installations (music, videos, project files, etc). I seem to be able to access that NTFS partition totally fine from Mint (like I've always done with W7), which is cool because I can access all that stuff regardless of which OS I'm using. I would like to know if it's possible (and how) to go one step further and share programs data between the two OS. One example would be my Firefox and Thunderbird data. For example, in Firefox share my bookmarks (and if I could share history, autocomplete and all that stuff, that would be awesome). In thunderbird, be able to share my mail and configuration, seeing the same inbox, folders, message rules, etc... So if I receive/send an email from W7 and later switch to Mint, I can see that email as it had been received/sent from Mint, and vice versa. Is this even possible? Or am I asking for too much convenience? If it's possible, any clues on how to set it all up?

  Read the article

• Notebook Operating System with extreme support cycles/security updates

  - by leto

  Hello there, after reading the announcements about Mac OS X "Lion" and Apples political decision, I've had enough. I'm a longtime Apple User since 1992, have always felt at home there, but am trying to switch to alternative Operating System since a year. I've also been working with Unix machines since 2001, so I'm looking in one of the free Unices or a Linux. Since I last looked at the desktop in 2002 choke much has changed, it seems. So I'm lost once more in the war between desktop environments and software. To be honest: I don't care what it's name is, I want to get my job done. Here's what I set me as landmark for an operating system/software to be considered: Has to be atleast four years old Has to supply security updates for current release for atleast a year Production quality stability for the whole desktop environment (!) No f****g commercial stuff that tends to supply me with privacy invading App Store or Cloud space So far I'm running a MacBook from 2007, 4 Gig memory, 250 Gig disk and I need: IMAPs for Mail since 1995 Webbrowser sic Shell Keeping current with Updates/Upgrades with no more than 5 Minutes spent in entering commands (makes it hard for OpenBSD ;-) ) A desktop filemanger would be nice, but is a bonus. What can you suggest as operating system? The one with the longest support cycles and best chance to survive the next 10 years will win a new user, even sending patches when needed :-) Greets

  Read the article

• Swapping out a hardware firewall does the mac address get cached?

  - by Dan

  We need to replace a hardware firewall (cisco pix) and have a spare that we will use (temporarily). The firewall sits in front of a couple of web-servers colocated at a data-centre. The replacement will be configured with identical settings (external/internal IP addresses, configured ports etc.). When we swap the firewalls over, will this work immediately or will the old Pix's mac address be cached and the new firewall not be seen until the cache is cleared? (What is it though that is caching the address? Is it just the switch/router that our pix is connected to?) Reason for asking is a few years ago I had a smoothwall firewall in front of a lone server (the external IP of the smoothwall was also the external IP of the web-server). When I replaced the smoothwall with a pix, the IP address of the web-server stayed the same but it now had to be reached via the new firewall on a different IP. It took about 2-4 hours before the rest of the world could see that web-server again. I'm hoping for less downtime this time!

  Read the article

• When machine is turned on, only the fan runs

  - by Gopal

  Hi, I have an issue slightly similar to this one posted here, http://superuser.com/questions/127016/troubleshooting-monitor-never-turns-on-system-fans-running-dvd-rom-does-not-op My configuration is as follows: EPOX 9NPA+ Ultra motherboard AMD Athlon 64 CPU Corsair 2 x 1GB PC3200 DDR RAM 1 DVD RW drive and 1 CD ROM Drive SATA 250 GB Hard drive 400W Power supply EVGA 256MB graphics card I have had this configuration for about four years. Last month, I started having issues in starting the machine. It wouldn't start when I press the ON button in the front of the case. So I used to pull out the power cord and plug it back in and then switch on in the front, and it used to work fine. And then one fine day, when I plugged in the power cord at the back, even without switching on the power-on button at the front, I saw that the fan at the back was running. So I opened the system. Then I could see that all the fans inside were running. I replaced the power supply. No luck there. Then I replaced the CMOS battery. Again nothing improved. Even when I removed all the cards and memory, I still get one short beep. That's it. Any idea how to proceed on this? Anything else could be checked? I want to confirm if this is a motherboard failure, before proceeding to replace it.

  Read the article

• How do I identify Blackberry / OWA users in my IIS logs?

  - by Quinten

  We just rolled out a Blackberry Express Server, and would like to make sure that all Blackberry devices that our users own are connecting SOLELY through the BES server. We are running Exchange 2010 SP1. I've read some links that discuss blocking BIS at the firewall level. Before doing that, however, I'd like to individually contact all users with Blackberries and make sure that they have a chance to switch to the BES server. I've sent a company-wide email, but unsurprisingly folks tend to tune these out until they are forced into action. Is there an easy way to identify the users with Blackberries by searching IIS logs, or perhaps using the Exchange Management Shell? Especially some automated way? I've tried searching for the Blackberry identifier, but it does not appear next to any user name, so it's not as helpful as it could be. Edit: to clarify, what I'm talking about is the fact that Blackberries can use OWA to download mail to the phone. We do not allow IMAP or POP access through our firewall so that's not a concern--just folks with Blackberries using Blackberry's hack to allow it to connect to Exchange without a BES server. As far as I know, Blackberries are the only popular phones that use this method to download mail.

  Read the article

• Not getting gigbit from a gigabit link?

  - by marcusw

  I just upgraded my LAN to gigabit. This is what netperf has to say about things. Before: marcus@lt:~$ netperf -H 192.168.1.1 TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 (192.168.1.1) port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.02 94.13 After: marcus@lt:~$ netperf -H 192.168.1.1 TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 (192.168.1.1) port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.01 339.15 Only 340 Mbps? What's up with that? Background info: I'm connecting through a gigabit switch to a sheevaplug. I have Cat5e wiring in the walls and the run is maybe 30 feet. If you're not familiar with netperf, it has a tendency to give very stable results and never lie.

  Read the article

• VLAN setup on my PC

  - by Surjya Narayana Padhi

  Hi Geeks, I am bit new to VLAN. I want my two computers communicate through VLAN. I have following queries. As I am new to it my queries may be somewhat vague in some points. But i would like to hear from experts for my basic queries. I have two PCs Computer A and Computer B in two different IP networks Network A and Network B Both my PC has windows OS installed. How to send a VLAN(#Number) tagged packet from Computer A to Computer B and how to detect and untag the packet at Computer B? (Please provide the steps for windows OS) For this action do I need to check if my ethernet card supports VLAN tagging/untagging? If yes how can I know if my card supports it or not? Is the VLAN applied for Wireless ethernet controllers also? Do I need any switch or router for this action? Experts please given your inputs so that I can have a strong basic. If anyone can give some inputs how i can detect those VLAN in wireshirk, it will be helpful me also. Thanks in advance.

  Read the article

• Problems using InfraRecorder to back up ISOs of certain CDs

  - by Voyagerfan5761

  I've gotten into the habit of backing up my CDs as ISO files, just in case the discs should be damanged, lost, or destroyed. Using InfraRecorder, the process is pretty painless. Unfortunately, I have run into at least two discs that don't back up. I get the error message: Can't read source disc. Retrying from sector 252270 Sometimes this will appear repeatedly. One of the discs is my retail copy of Star Trek: Armada II; the other is disc one of DOOM 3. Both discs run flawlessly when I put them in the drive and let Windows AutoPlay them. Armada II appears as two tracks (one data, one audio) in InfraRecorder, and the error happens at the approximate track boundary. DOOM 3's first disc, however, fails much sooner (around sector 990) and appears as one solid data track. Am I simply using the wrong tools for this job? InfraRecorder is a nice free tool that I can run from my flash drive and use for most tasks of this type, but it does seem to have trouble with certain things. Ideally I'd like to hear about any workarounds people have found for this issue, but if I must switch tools I'm open to it (preferably other free tools).

  Read the article

• Small TCP Window on WAN between 2 Locations

  - by Brent

  Site A: Denver datacenter. 60MBPS. Site B: Chicago. 100MBPS. ICMP pings: Packets: Sent = 176, Received = 176, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 74ms, Maximum = 94ms, Average = 75ms File transfer between sites that never goes past ~7MBPS: Windows Update download at 60MBPS+: Site to site: IPSec VPN using two Cisco 5520's. CPU at 3-4% and lots of memory to spare. The latency between to two sites is very acceptable so I can't see an issue why it is performing so slow when transferring between the two sites. I have found that any type of transfer (FTP, HTTP, Windows file shares) will never go above ~7MBPS. When the WAN was first setup, I was able to get transfers at 50-60MBPS, which is what is expected due to the WAN connection at the Site A at 60MBPS. Then a few days later, I was not able to get anything going faster than ~7MBPS. Is there a upstream router between Denver and Chicago causing this? I want to take the blame away from our setup as downloads from Windows Update go blazing fast and for the first few days after the site to site VPN came up, I was transferring VM images at 50-60MBPS. Our stack: HP P2000 MSA - HP C7000 Chassis - HP Flex-10 - Cisco Gigabit switch - Cisco ASA - WAN

  Read the article

• SBD killing both cluster nodes when there are even small SAN network problems

  - by Wieslaw Herr

  I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

  Read the article

• Modify or disable Windows 8 swipe gestures on touchpad / laptop

  - by Matsemann

  I have an ASUS G75VW laptop with a Synaptic touchpad (/trackpad). When I move my finger from one edge towards the middle (the swipe), Windows 8 will bring up different stuff. This is a problem because the area where I can actually move the mouse with my finger is too small (or, I mostly use the top left of the touchpad). So I often end up doing a swipe and bringing up some menu, or to do the swipe so slow that no menu is appearing but the mouse pointer is also not moving when I move my finger. Quite annoying. When swiping from left edge it earlier swapped apps like crazy. I disabled that, so now it only brings up the same menu as pressing win+tab (or some times the charms bar, I never know which). I could change that by: Win+I - Change PC settings - General - When I swipe from the left edge, switch directly to my most recent app I've tried Mouse settings in Control Panel, driver settings for my touchpad and searching for swipe and gestures on my computer (which was what led me to the setting above) with no luck. How can I disable the swipe gestures, or change what they do? Thanks.

  Read the article

• IIS crashes with unhandled exception in ASP.NET

  - by SnowCrash

  We had an issue recently with an unhandled exception in an ASP.NET C# application bringing down IIS and all application pools that it was hosting. IIS Manager was unable to restart or stop/start the service and I was unable start IIS again after killing w3wp.exe in the task manager. A system reboot restored IIS to a running state; as a primarily Linux admin, I generally consider an unplanned system reboot to resolve a software error to be an act of high heresy. Is there a way to "harden" IIS so that a faulting application does not affect anything but the request that exposes the fault? Some details on the server and application fault. IIS: 7.5 .NET: 4.0 Windows Server 2008 R2 Faulted on call to System.Net.Dns.Resolve() with a url pointing to a non-existant domain as the argument. (I'm aware that this method is deprecated but the point that a page code issue shouldn't bring down the server still stands) The exception generated was SocketException. The faulting module according to event viewer was KERNELBASE.dll The issue was resolved by wrapping the call in a try-catch, logging the exception and displaying some generic content on the page. I'm hoping that I missed something in the IIS config that would switch it to "production" mode or something.

  Read the article

• Apache httpd workers retry

  - by David Newcomb

  I have an Apache httpd web server running mod_proxy and mod_proxy_balancer. The whole of /somedir is sent to 2 worker machines which service the requests using the round robin scheduler. Each worker machine is running IIS but I don't think that is important. I can demonstrate the load balancer working by repeatedly requesting a single page which contains the IP address of the machine and can see that it switches from one to the other in a predictable round robin fashion. If I switch off one of the IIS servers and start requesting the same page then each page only contains the IP address of the machine that is up. However, if I start IIS and don't run my IIS application then /somedir returns 500 (as it should). I've added 500 to the failonstatus (Apache 2.4) so when it hits the error Apache places the worker machine into error state. Apache still returns the proxy error to the client though. How can I make Apache catch the proxy failure and retry using a different worker in the same way that a connection failure does. Update There is almost the same question asked in StackOverflow so joining them together. http://stackoverflow.com/questions/11083707/httpd-mod-proxy-balancer-failover-failonstatus-transperant-switching

  Read the article

• Has anyone had luck running 802.1x over ethernet using the stock Windows or other free supplicant?

  - by maxxpower

  I just wanted to see if anyone else has had luck implementing 802.1x over ethernet. So here's my basic setup. Switch sends out 3 eapol messages spaced out 5 seconds apart. if there's no response the machine gets put on a guest vlan with restricted access. If the machine is properly configured it will authenticate and be placed into a secure vlan. About 10% of my windows xp users are getting self assigned 169 addresses. I've used the Odyssey Access Client and it worked without a hitch. I'm using the setting to automatically use the users windows login to authenticate, but it's workign on 90% of the machines so I don't think that's the issue. Checking the logs on the dc it seems that the machines are trying to authenticate with computer credentials even though they are configured not to. I'm running Juniper switches with IAS for radius. I have radius configured for PEAP and MSvhapv2. Macs and linux boxes seem to have no issues authenticating. One last thing to add If I unplugging the ethernet cable and plug it back in usually resolves the issue, but I'd hardly call that acceptable for production. Kinda long winded and specific for a discussion, but just want to see if anyone else has had similar issues or experiences, or if anyone knows of a free XP supplicant that actually works with 802.1x over ethernet.

  Read the article

• Ubuntu - No gnome-panels, no right-click, no internet, no hotkeys

  - by Darthfett

  Hey guys, I've been using Ubuntu (Maverick 10.10) on my desktop (ATI Radeon 5830) for about 3 weeks now, but all of a sudden I am unable to even use my computer. As soon as I start up, I see my desktop, with icons, but I don't see any gnome-panels, and I'm unable to get any options if I right-click. I can start programs by double clicking them. I also cannot get an internet connection. I've tried restarting gnome-panel by killing it, using Ctrl+Alt+5 to switch to a terminal (I don't have a shortcut to one on my desktop, and no hotkeys will work), but no luck. Restarting my computer has no effect upon this (I have to manually cut the power, since I don't know the terminal command). As far as I know, I have not made any changes, and I've never had any problems in the past. This started when I was playing Minecraft, but my internet crapped out, and no amount of re-trying the connection would work. I know it was my computer, as my brother's was working fine in the other room. Any clues as to what's going on? I'm more than willing to troubleshoot.

  Read the article

• Making "default saved" work with GRUB2...?

  - by baltusaj

  I just installed Moblin Operating System. It's using GRUB2. On my Ubuntu 8.04 GRUB 0.97 was being used in which i was using the default saved option comfortably. I found that with GRUB2 i should not edit /boot/grub/menu.lst directly but I did :) because my Moblin does not contain any /etc/default/grub where they say I should do the modification I want. So what I did is as following which did not work: default=saved timeout=1 #splashimage=(hd0,0)/boot/grub/splash.xpm.gz #hiddenmenu #silent title Moblin (2.6.31.5-10.1.moblin2-netbook) root (hd0,0) kernel /boot/vmlinuz-2.6.31.5-10.1.moblin2-netbook ro root=/dev/sda1 vga=current savedefault=1 title Pathetic Windows rootnoverify (hd0,1) chainloader +1 savedefault=0 By doing so I should have automatically switch between Moblin and Window at each boot but it's not working. Almost all the troubleshooters on internet are saying that I should enable the DEFAULT=save option in /etc/default/grub but I am unable to find this file. Any idea what else should I do? Thanks a lot Update: I used the equal to sign because by default my menu.lst had an entry as default=0. However, default 0, is also working fine. Moreover the menu.lst, i have is actually a symbolic link to ./grub.conf. I have also noticed that grub-intall and grub-set-default commands are not working.

  Read the article

• apache on Cent OS opening default page on https

  - by Asghar

  I am new to apache and SSL and configuration, i got verysign certificte to secure my site. i have public, private and ca_intermediate cert files. i have configured ssl.conf as below VirtualHost _default_:443> DocumentRoot /var/www/mydomain.com/web/ ServerName mydomain.com:443 ServerAlias www.mydomain.com # Use separate log files for the SSL virtual host; note that LogLevel # is not inherited from httpd.conf. ErrorLog logs/ssl_error_log TransferLog logs/ssl_access_log LogLevel warn # SSL Engine Switch: # Enable/Disable SSL for this virtual host. SSLEngine on problem is that when i access www.mydoamin.com with "HTTP" it works fine, but when i access using "HTTPS" it just opens apache default page. but with green "HTTPS" means my certificates are installed correctly. How can i get rid of this situtaion. Thanks EDIT Output of apachectl -S -bash-3.2# apachectl -S [Mon Aug 27 10:20:19 2012] [warn] NameVirtualHost 82.56.29.189:80 has no VirtualHosts [Mon Aug 27 10:20:19 2012] [warn] NameVirtualHost 82.56.29.189:443 has no VirtualHosts VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: _default_:8081 localhost.localdomain (/etc/httpd/conf/sites-enabled/000-apps.vhost:10) *:8080 is a NameVirtualHost default server localhost.localdomain (/etc/httpd/conf/sites-enabled/000-ispconfig.vhost:10) port 8080 namevhost localhost.localdomain (/etc/httpd/conf/sites-enabled/000-ispconfig.vhost:10) *:443 is a NameVirtualHost default server mydomain.com (/etc/httpd/conf.d/ssl.conf:81) port 443 namevhost mydomain.com (/etc/httpd/conf.d/ssl.conf:81) *:80 is a NameVirtualHost default server app.mydomain.com (/etc/httpd/conf/sites-enabled/100-app.mydomain.com.vhost:7) port 80 namevhost app.mydomain.com (/etc/httpd/conf/sites-enabled/100-app.mydomain.com.vhost:7) port 80 namevhost mydomain.com (/etc/httpd/conf/sites-enabled/100-mydomain.com.vhost:7) Syntax OK

  Read the article

• Cisco BVI: Claiming IP addresses

  - by cjavapro

  I would like to make sure I understand this correctly. Given a Cisco ISO router that is set up with a BVI (a variation of a bridge route).. and the following layout "ISP router" \ "Network switch" # nothing special here. | \ | \ | \ | \ "Router 1 with NAT" "Router 2 with BVI" If I understand correctly.. the outside of a BVI will only respond to IP addresses that have already been claimed on the inside of the BVI... example subnet is 123.123.123.??? and servers inside the BVI on 123.123.123.10 and 123.123.123.11, and the NAT router is holding a public IP address of 123.123.123.50. If a connection comes in to 123.123.123.10 it will be received by router 2 but if it is received on 123.123.123.50, it will be received by router 1 and not received by router 2. and if a connection comes in to 123.123.123.90 (does not exist) it will not be received by either router. Am I correct? Is it true that the BVI router will not even receive packets to IP addresses that it does not see as existing on the inside?

  Read the article

• Why can't I physically access my machine after a remote session?

  - by Steve Crane

  I have a Dell Optiplex 960 desktop running Windows 7 64-bit at work. I typically leave it locked rather than logged off when I go home, so that I'm able to remote in from home and continue working if I wish. This is where the problem comes in. If I don't remote in there is no problem and I can simply unlock the next morning. It's when I do remote in that I have a problem. Remote sessions work as expected but when I get to work the next morning the machine appears to have gone into a sleep or hibernate state, from which no amount of mouse moving or keyboard pounding will wake it. The machine is not hanging as remote sessions to it are still possible; it seems that physical access from it's own mouse and keyboard are lost. The only way to gain access is to press and hold the power switch for several seconds until the machine shuts down. Of course this means Windows does not gracefully shut down and after powering up it takes several minutes for the machine to boot and reach the login prompt; presumably while it checks the disk. Has anyone else seen something like this?

  Read the article

< Previous Page | 652 653 654 655 656 657 658 659 660 661 662 663  | Next Page >