Search Results

Search found 3195 results on 128 pages for 'utility'.

Page 68/128 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• solaris + EMC + power-path

  - by yael

  please advice - when I run powercf command on my Solaris machine , which changes this command do on the EMC storage , or on Solaris file system ? from maanual page: DESCRIPTION During system boot on Solaris hosts, the powercf utility configures PowerPath devices by scanning the HBAs for both single-ported and multiported storage system logical dev- ices. (A multiported logical device shows up on two or more HBAs with the same storage system subsystem/device identity. The identity comes from the serial number for the logical device.) For each storage system logical device found in the scan of the HBAs, powercf creates a corresponding emcpower device entry in the emcp.conf file, and it saves a primary path and an alternate primary path to that device.

  Read the article

• misaligned raid partition in Ubuntu 10.04

  - by Linux Jedi

  I attached two identical hard drives to my linux machine. Then using gparted I formated the first 1024 mb at the beginning of each drive as linux swap space. Then I went into system-administration-disk utility. In there I went to file-create-RAID array. I selected the remaining space in each of the two identical hard drives and created a striped raid array. After the array was created, a warning message appeared. It said "The partition is misaligned by 522240 bytes. This may result in very poor performance. Repartitioning is suggested." What do I do now? As far as I can tell, the partitions are identical.

  Read the article

• Expanding RAID 1 array size (Adaptec 1420SA controller)

  - by cincura.net

  I have an Adaptec 1420SA controller in server and RAID 1 array created. The old disks slowly started to report S.M.A.R.T errors so I replaced first one, rebuild array and then other one and rebuild the array again. But the new drives are bigger, so I'd like to expand the array to use full disk capacity. Is it somehow possible? In the Adaptec configuration utility, after POST, I didn't found anything that could do it. I still have the old drives, if it helps. The array is used for system (Windows 2008 R2 SP1) booting. Thanks.

  Read the article

• WD Passport Won't Mount

  - by Scott7278

  My WD Passport won't mount. However, it turns on when plugged into my macbook and doesn't make any strange noises. It took a small fall (just a few inches and it was on my couch) and I'm very concerned about physical damage. When I open up disk utility it shows the root 500 GB WD My Passport drive which seems to be OK when I verify it and repair it. However, the "External Hard Drive", the directory underneath the "500 GB WD My Passport drive" is grayed out. When I verify the External Hard Drive it says it needs to be rapaired. When I try and repair it it gives me the following message and does not seem to progress: "Updating boot support partitions for the volume as required." Is there hope for me recovering my data? I stupidly have important data on it that I don't have anywhere else.

  Read the article

• Convert SWF/FLA back to PDF [closed]

  - by mitjak

  Possible Duplicate: How do I convert SWF into a PDF? I have a number of graphics and text only SWF and FLA files that I'd like to convert to PDF preserving the text and formatting. Printing to PDF from Flash Player seems to flatten everything into an image without preserving the text. I've got a large number of those files, so it would be quite nice to have a automatable/console utility to do the job. Appreciate any help or pointers. Thanks! EDIT: It seems like most SWF files were created with pdf2swf, so I'm hoping there is a similar tool for doing a reverse conversion.

  Read the article

• Can I run my MacBook in clamshell mode without being connected to power?

  - by kch

  Hi, At home, I run my MacBook in clamshell mode (closed lid, external display). This works fine when you're connected to the power adapter, but it doesn't work when running on battery. That's how it's supposed to be and Apple has some kb entry on the issue. But it's also lame. You can prevent the machine from sleeping when closed by running InsomniaX, but then it'll assume the builtin display is still active, so you end up with a two-display setup when you really only want the external. This is obviously less than ideal. So, is there any work around, hack, utility, black magic that I can use to make it run in clamshell mode while strictly on battery power? Also, bonus points for a solution that makes the AC status not affect the machine state at all. (Like, you know, it does normally, when not in clamshell.)

  Read the article

• Need to automount dvd or cdrom at fixed mount point in Ubuntu 11.04

  - by Lindsay Haisley

  Ubuntu 11.04, by default, automounts a cdrom or dvd at /media/<vol_name>. I need to make the automounting system use a fixed name instead of the volume name for all CDs or DVDs inserted into this particular drive, e.g. "/media/op-drive0". A bit of searching turns up pretty much the same solution I used, successfully, on an older, gentoo box, which is to create an fdi file for hal, along the lines of the instructions at https://bbs.archlinux.org/viewtopic.php?id=91450. This doesn't seem to work on this box. Other sources say to use the gnome-mount utility to set the mounting properties. Ubuntu 11.04 doesn't know about the gnome-mount program. Any ideas?

  Read the article

• iPhone VPN to iTunes Home Sharing

  - by Philip Crumpton

  my goal is to set up a VPN on a Windows machine that contains my iTunes library then connect to that VPN with my iPhone and be able to utilize Home Sharing remotely. I have read that this can easily be set up if the iTunes library is on a Mac (Network Beacon and YazSoft ShareTool are two products I quickly found). I can't find anyone who has had success on a Windows machine, though. In my thinking, there are two options (aside from buying a Mac): 1.) Existing utility that takes care of this for me (like the Mac-only options listed above) and is compatible with iPhone (Hamachi is NOT compatible with iPhone VPN) 2.) Manually configure a VPN to allow Bonjour multicast (can't find any information on this) FYI my router is a Linksys WRT54GL running Tomato 1.28

  Read the article

• Manual TRIM Windows 7 on OCZ VERTEX 2 SATA II 2.5" SSD

  - by INTPnerd

  I have an OCZ VERTEX 2 SATA II 2.5" SSD with Windows 7 Professional installed on it. I am pretty sure TRIM is not working because my motherboard is the Asus M2N-SLI (not the Deluxe model) which does not support AHCI mode for the drive. Is there a utility that is compatible with this drive that I could possibly run once a day that would do something similar to a manual TRIM in order to keep the drive performance up? I could not find one specifically for this drive on the OCZ website. I did find a User-Initiated Garbage Collection wiper tool, but it is for a Vertex drive not Vertex 2. I tried to run it, but it said that wiper could not be run for all the drives on this system.

  Read the article

• Accidentally ejected my Verbatim drive and can't get the icon back

  - by Erin

  Hi, I have time machine running on my iMac OSX v10.5.8 and also have a Verbatim 1TB attached that I use as a workspace/scratchdisk so I can manipulate large music files before I transfer them. However, when cleaning behind my computer the other day I think I dislodged the connection (or maybe one of the kids hit the eject button, i don't know) however, I've re-booted many times and it's not reconnected. It doesn't appear in my disc utility windown and I don't know how to get the icon back! I've looked in time machine but it doesn't appear there at all (cos it's not supposed to I think - it's not connected - my mate hooked it up for me and he won't return my calls!). Help. I don't know how to get it back! Sorry for being a plank.

  Read the article

• Best way to log internet traffic for office network via remote IP

  - by buzzmonkey

  We have a network of about 40 machines running either Win XP or 7 in our office via LAN switches into 1 x Netgear Router (WNDR3700). We have noticed recently that our local network has been added to the CBL Blacklist due to one of our machines being infected with Torpig. I have attempted to use Kaspersky's TDSSKiller Antirootkit Utility to find the infected machine but all appear to be clear. The CBL register advises to find the local machine which is connection to the remote IP address (CBL has provided the range). However, our router does not have the ability to block remote IP addresses - does anyone know of a software which can log all the internet traffic, which we can then use to find the infected machine.

  Read the article

• Unused Index Entries: What causes them?

  - by Bart Silverstrim

  I was running chkdsk on one of our servers and it fixed 800 unused index entries (minor inconsistencies) on the drive. I also see these on lab machines running Deep Freeze, where most drive changes are supposed to be prevented although I'm not sure of the mechanism through which it does this. The thing that got me more curious than usual is that this server does very little. Very little activity, it remotely serves out a web app with little use so it's rarely ever touched at the console...so what is it on NTFS drives that causes this? It seems to be treated as if it's nothing, but should this be happening on a barely used filesystem? Is it a sign of corruption? I would think it's something if a disk repair utility sees fit to report it and repair it. Maybe this is more curiosity while doing some routine maintenance on servers, but I'd like to know what this is doing and why it happens, if anyone can give insight on this phenomena.

  Read the article

• Repartition hard drive using Mac OS X, keep existing data

  - by Jonny

  I got a 1 TB disk a year or so ago and loaded it with some hundred of GB of data. I somehow neglected to check the file system, which turns out to be FAT-32 and thus too small for files bigger than 4 GB. So now I want to change it, without deleting the data. I thought I'd just make a new partition in the so far unused space. Then with the new partition, copy/move the data into the new partition, and then delete the old FAT-32 partition, and make the new partition bigger again... or just make a few more partitions. The critical step here is, can I make that new partition without ruining the data? The data should be fairly sequentially added to the start of the disk, but what do I know... so that's why I'm asking. Can I safely use Disk Utility for this? Any recommended file system?

  Read the article

• gunzip unexpected end of file

  - by Mark J Seger

  I like to write high volume data directly to a zip file via perl. Works like a champ! However, on some rare occasions I've found that gunzip can't uncompress them declaring an unexpected end-of-file. The thing is I can uncompress it with a simple perl script, which probably misses the corrupted record(s) at the end. My question is, does anyone know of a way to use a standard utility to do the same thing? Maybe with a 'compress-as-much-as-you-can' switch? -mark

  Read the article

• Catch and identify source of browser launch events

  - by beldaz

  My Windows XP computer is exhibiting strange behaviour, launching multiple browser windows, but not to any URL. Initially this was in Firefox, but when I uninstalled it the same happened in IE. Norton 360 detects no malware, and I wonder if there is some application that is accidentally causing the problem. I'd like to diagnose the problem further. It seems that the default browser is being launched by something, so I'd like to work out the culprit. Is there some method (or handy utility) that can catch requests to XP to launch the default browser, and identify the source?

  Read the article

• Configuring bridged network connection --- Windows 7 host, Ubuntu 10.04 guest --- VMWare Workstation 8

  - by H3br3wHamm3r81

  Here is my IPCONFIG /ALL from the host (Windows 7 64-bit): Here is my IFCONFIG from the guest (Ubuntu 10.04): To be honest, I don't have experience configuring a network between a host and a guest in VMWare (a virtual machine). I've searched high and low on the internet, but I haven't seen anything that can help. Perhaps I'm just not using the right keywords when I search. Nevertheless, does anyone here have any experience with establishing a network connection? Edit: One important note. I don't use DHCP to provide private addresses to the hosts on my LAN. I use "static" IP addresses on my internal network by configuring each IP address manually in the host's network configuration utility (I have TV's, XBOX 360, and a few PC's). I would like to configure the IP on the virtual machine guest manually as well. The reason is because my XBOX 360 only works properly using a static IP address. It will kick me off XBOX Live if it has one given by the router (via DHCP).

  Read the article

• There is a problem with the Office database

  - by RomanT

  After a TimeMachine restore; office 2011 is having kittens over permissions it would seem. Having attempted a 'repair' out of Disk Utility, am still seeing: 'there is a problem with the Office database' upon startup. After which Word/Excel work without issues. Outlook on the other hand won't even start. Given the obvious message here "You do not have write access to the Outlook application folder" - where is the DB located to check?! Ideas ? Thank you

  Read the article

• Folders disappear every timeWindows XP starts up

  - by Reebz

  Whenever my Windows XP machine starts up, subfolders disappear from the first top-level folder, listed alphabetically (eg. from "C:\AA Backups"). The first time it happened I suspected user error (such as an unintentional delete or copy). But I then found it happens on every start-up, sometimes affecting huge numbers of files. Renaming the affected folder (eg to "ZZ Backups") just means that a different folder is affected the next time. Avast found no virus or malware that would seem to be responsible. The missing files are not visible to an undelete utility such as NTFSUndelete. Running "chkdsk/f" found no problems and did not fix the problem. File permissions also appear corrupted - a few files which should be accessible are missing "read" permission. What's happened to this machine?? Any ideas or reports of similar experiences would be most welcome.

  Read the article

• Corrupted file, hard drive test?

  - by all-R

  Hi guys, I'm currently on a macbook with a 1TB external hard drive connected trough a USB hub wich is connected on my macbook. The problem is, my disk, wich is partitioned in 2 (one HFS+ and one NTFS) keeps getting corrupted, recently it was my HFS+ partition, I could not repair it using the Apple's Disk utility, but was able to backup my files. Is it synonym that my hard drive is failing? Is it because of my USB hub? I also keep all my iTunes library on my external HD (HFS+ partition), and did a lot of transfer lately, adding files, removing etc. the last time, my partition got corrupted after a lot of deleted items. If anybody has an idea of what to check first, what could cause the problem, I would appreciate it :) Thanks!

  Read the article

• Synchronisation software to find files that have moved paths within a folder?

  - by kpierce8

  Say I have a pictures folder which I reorganized on one computer. I'd like to use that directory as the base and compare it with another version on a backup drive. Will any Synchronisation/compare program find that a file in one folder has moved locations within a compare folder? For instance, say I reorganized my pictures from trips into folders by year with the trips folders inside each year folder. If I use a regular compare utility I wind up with two copies of everything that's moved in different locations.

  Read the article

• My NTFS Partition keeps becoming "unusable" on Ubuntu, Any Ideas?

  - by gopherman

  I just purchased a new 2TB Drive External Seagate, My main system uses both Windows and Ubuntu So I am pretty much stuck with keeping my drive as NTFS. I have done this without any problems before but since I got this new drive I have been having issues. When I first load up Ubuntu the drive mounts and runs fine, after an unspecified amount of time i start getting Input/Output errors when accessing the drive. When I goto the Disk Utility I get a message stating the drive is "Unknown or Unused", If I disconnect and reconnect the drive or reboot everything is fine again. There's no errors coming up with S.M.A.R.T and it seems to work fine while under windows. Any thoughts?

  Read the article

• My NTFS Partition keeps becoming "unusable" on Ubuntu, Any Ideas?

  - by gopherman

  I just purchased a new 2TB Drive External Seagate, My main system uses both Windows and Ubuntu So I am pretty much stuck with keeping my drive as NTFS. I have done this without any problems before but since I got this new drive I have been having issues. When I first load up Ubuntu the drive mounts and runs fine, after an unspecified amount of time i start getting Input/Output errors when accessing the drive. When I goto the Disk Utility I get a message stating the drive is "Unknown or Unused", If I disconnect and reconnect the drive or reboot everything is fine again. There's no errors coming up with S.M.A.R.T and it seems to work fine while under windows. Any thoughts?

  Read the article

• Virtual Screen Splitter

  - by dabest1

  I am looking for a utility that will allow my screen to be split into two sections. I would like to do this so that programs can easily fill or get sized properly to one part of the screen. This way I can pretend that I have a separate monitor for working on my stuff, while my kids can watch something on the other side. In addition, this should help prevent any popups covering up their side of the screen. Although Windows 7 comes with ability to drag a program window to a side and it becomes sized to half of the screen automatically, this is insufficient for me. I would like to make sure that any programs I launch or any pop-ups that open up, do not block the other side of the screen, even for a short time. Also, I am not looking for a virtual OS solution, as in VirtualBox.

  Read the article

• Restore Picasa people tags

  - by Paul

  I have loaded Windows 7 to my laptop. Before doing this I backed up all my pictures using the Picasa backup utility. I then ran a restore on the clean Windows 7 install. I then installed Picasa 3.5 and none of the people tags showed up. I then went and deleted what I thought was the Picasa DB and then tried running the restore again. Now each folder shows up twice in Picasa but only once under the Windows Pictures folder. How do I get rid of the duplicates in Picasa and get my people tags back?

  Read the article

• which command run in cron returns nothing

  - by Zárate

  Hi there, I've written a little utility in haXe + Neko that needs to execute some GIT commands. To avoid hardcoding the path to the GIT executable I'd like to use the which command to find out where it is. Everything works as expected when running manually from the console, but not when the the app runs on a cron job. I'm aware of the restricted environment (here or here) when you run a script using cron, but still surprised this doesn't work: /usr/bin/which git >> /home/user/git.txt The text file is created but the content is empty. Again, when run from the console it works as expected. Any ideas? I'm running OS X Leopard, if that helps. Thanks : ) Juan

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >