Search Results

Search found 21463 results on 859 pages for 'broken link'.

Page 693/859 | < Previous Page | 689 690 691 692 693 694 695 696 697 698 699 700  | Next Page >

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• What is the correct iptables rule when NATing multiple private subnets?

  - by Jose Mendez

  I have a Centos minimal 6.5 acting as a router. eth0 is connected to a Cisco switch trunk port, allowing VLANs 200-213. I have several VLAN interfaces just as this link suggests: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s2-networkscripts-interfaces_802.1q-vlan-tagging.html And have IPv4 forwarding, so all my network devices from any of the networks 200-213 can communicate with each other using this linux box as their router. Problem is, I need them to access the Internet, so I added the following rule: iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to 1.1.1.56 1.1.1.56 is the "outside" address. This works fine, devices connected to the internal networks can ping Intertnet addresses BUT, they stop being able to talk to each other across subnets, so 192.168.211.55 can ping 8.8.8.8, but can't talk to 192.168.213.5. As soon as I do a service iptables restart to remove the rule, I can start talking across internal subnets again. What would be the correct way to set up NAT for multiple private subnets? Or maybe the correct way to set up forwarding?

  Read the article

• Multiple IPv6 addresses being assigned to single interface

  - by Steven Copestake

  I'm configuring a DHCP scope for IPv6, however all my clients are getting 2 or more IPv6 addresses assigned to the interface. I'm using fda8:6c3:ce53:a890:/64 as the prefix. The scope is on a machine running Windows Server 2008 R2 however I'm looking to roll it out on Server 2012 as well. My clients are getting the following: IPv6 Address. . . . . . . . . . . : 1024::1492:9288:7357:7d30(Preferred) IPv6 Address. . . . . . . . . . . : fda8:6c3:ce53:a890::1(Preferred) IPv6 Address. . . . . . . . . . . : fda8:6c3:ce53:a890:1492:9288:7357:7d30(Pr rred) Link-local IPv6 Address . . . . . : fe80::1492:9288:7357:7d30%10(Preferred) In this example there's no DHCP scope and the machine has a static IP of fda8:6c3:ce53:a890::1. With this in mind where are the 1024 address and the fda8:6c3:ce53:a890:1492:9288:7357:7d30 address coming from?

  Read the article

• Running the LibreOffice MSI installer in English

  - by Scott Severance

  I'm trying to install LibreOffice on a machine running a Korean version of Windows XP. I don't know Korean. I haven't used Windows with any frequency in many years, so I'm pretty lost. When I run the installer, it shows up in Korean. But, I want to customize the installation, so I need the installer to be in English. Googling took me to this page, where I found an example command to run the installer in Gaelic, which I modified for my system as follows: msiexec /i LibO_3.6.1_Win_x86_install_multi.msi TRANSFORMS=:1084 This works, except that I know less about Gaelic than I do about Korean. The help page provided a link to a page where I could look up the ID codes. From that page, I determined that the correct code was 1033 for US English and 2057 for UK English. When I substituted the code, I got an error message. Here's the messages as translated by Google, followed by the original: Transform can not be applied.Verify that the specified transform paths are valid. ?? ??? ??? ? ????. ??? ?? ??? ???? ?????. I can't very well search on a machine translation, so I don't know where to go from here.What is the problem? How can I make the installer operate in English? Alternatively, how can I change XP to display its interface in English, while keeping full functionality for typing in Korean?

  Read the article

• How can I download a file directly to a web server?

  - by matt

  I'd like to download files directly to a hosted server, whether it's one I set up myself or a hosted service like Dropbox. For example, when I download a podcast, instead of downloading it to my computer then uploading it to the server, how can I have it download directly to the cloud. My interest here is reducing the traffic I'm using over a metered data plan on my laptop, so I don't want my computer acting as a physical intermediary caching the file. Ideally, there would be some way for me to have a download link and tell it to go directly to my server. How can I accomplish this? I realize that this question is potentially involving a "webapp" and it is potentially involving "server administration" and since my goal is to cut my computer out of the loop I can see people saying this is off-topic and should be on another site. My issue is this: I don't know if this is going to be a webapp solution or a server solution but I do know regardless I'm going to be using a computer to get it done and I am replacing a function that's currently done on my computer so I figured I'd ask it here. If I was wrong and this definitely should be at webapps feel free to let me know or just migrate it.

  Read the article

• How do I stop MSYS from transforming my compiler options?

  - by Carl Norum

  Is there a way to stop MSYS/MinGW from transforming what it thinks are paths on my command lines? I have a project that's using nmake & Microsoft Visual Studio 2003 (yeecccch). I have the build system all ported and ready to go for GNU make (and tested with Cygwin). Something weird is happening to my compiler flags when I try to compile in an MSYS environment, though. Here's a simplified example: $ cl /nologo Microsoft (R) 32-bit C/C++ Optimizing Compiler Version 13.10.6030 for 80x86 Copyright (C) Microsoft Corporation. All rights reserved. /out:nologo.exe C:/msys/1.0/nologo LINK : fatal error LNK1181: cannot open input file 'C:/msys/1.0/nologo.obj' As you can see, MSYS is transforming the /nologo compiler switch into a windows path, and then sending that to the compiler. I really don't want this to happen - in fact I'd be happy if MSYS never transformed any paths - my build system had to take care of all that when I first ported to Cygwin. Is there a way to make that happen? It does work to change the command to $ cl -nologo Which produces the expected results, but this build system is very large and very painful to update. I really don't want to have to go in and change every use of a / for a flag to a -. In particular, there may be tools that don't support the use of the - at all, and then I'll really be stuck. Thanks for any suggestions!

  Read the article

• How to keep Ubuntu 11.10 and Kate editor w/terminal from changing command line when changing tabs?

  - by Kairan

  I am programming C using Kate editor in Ubuntu 11.10. It works great, but when I change tabs in Kate, the terminal line changes to the file path of the tab I click on. Normally this is not a big deal (other than annoyingly adding extra text to my terminal) however if I am currently RUNNNING a C program, it obviously will type at the command line, which is not so cool. Example terminal window for my C program (its at a menu): 1) select opt 1 2) select opt 2 Enter choice: (here it waits for prompt from user) Now when I click a tab in Kate, it wants to put in the cd / path of the file in that tab, such as: cd /home/user/os/files And of course since my terminal was waiting for prompt from user it gets that command.. not good. Perhaps there is no fix, but maybe someone knows? Obviously I could choose NOT to switch tabs or end program before switching tabs... Note: I probably made the mistake of putting this under StackOverflow which is more of a programming area - so though repost here might be best (I am not sure how to link the questions but will paste hyperlink to that post - I dont want to violate any stackoverflow/superuser violations) Suggestions on merging them are welcome or if I should delete one? StackOverFlow Question

  Read the article

• OS X can't copy files from Windows Home Server...over wifi.

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks!

  Read the article

• Google Chrome doesn't respond user actions correctly

  - by Carlos A. Junior

  Recently I've changed my OS to Ubuntu 12.04 (Cinnamon, 64 bits) from Mint 13 (KDE, 64 bits) and one same bug still appears on new installation. The Google Chrome it seems that don't refresh (repaint) page based on my interactions. Example: When i'm try comment an Youtube vídeo, when i click on textarea, o cursor don't appear inside of textarea, BUT, when/if i change to another tab and return the cursor appears...OK... If i start write some text...according i'm typing the chars don't appers...again if i change to another tab and return the typed text appears on textarea. Other cases that this bug appears: Modal boxes link...don't show the modal; Forms inside modal boxes don't show typed chars; The common Discus comment plugin don't work when focused; I don't have any idea of reason of this bug. (video driver, window manager, Chrome bug ?, i don't know) Any idea to solve this ? Additional informations: Google Chrome 22.0.1229.79 (Official Build 158531) OS Linux WebKit 537.4 (@129177) JavaScript V8 3.12.19.11 Flash 11.3.31.331 User Agent Mozilla/5.0 (X11; Linux i686) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.79 Safari/537.4 Command Line /opt/google/chrome/google-chrome --flag-switches-begin --flag-switches-end Executable Path /opt/google/chrome/google-chrome Profile Path /home/carlos/.config/google-chrome/Default Kernel version: 3.2.0-31-generic-pae Ubuntu 12.04 Best regards.

  Read the article

• Packet drop measured by ethtool, tcpdump and ifconfig

  - by Rayne

  Hi all, I have a question regarding packet drops. I am running a test to determine when packet drops occur. I'm using a Spirent TestCenter through a switch (necessary to aggregate Ethernet traffic from 5 ports to one optical link) to a server using a Myricom card. While running my test, if the input rate is below a certain value, ethtool does not report any drop (except dropped_multicast_filtered which is incrementing at a very slow rate). However, tcpdump reports X number of packets "dropped by kernel". Then if I increase the input rate, ethtool reports drops but "ifconfig eth2" does not. In fact, ifconfig doesn't seem to report any packet drops at all. Do they all measure packet drops at different "levels", i.e. ethtool at the NIC level, tcpdump at the kernel level etc? And am I right to say that in the journey of an incoming packet, the NIC level is the "so-called" first level, then the kernel, then the user application? So any packet drop is likely to happen first at the NIC, then the kernel, then the user application? So if there is no packet drop at the NIC, but packet drop at the kernel, then the bottleneck is not at the NIC? Thank you. Regards, Rayne

  Read the article

• Windows 7 - system error 5 problem

  - by Ian

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• How to install a private user script in Chrome 21+?

  - by Mathias Bynens

  In Chrome 20 and older versions, you could simply open any .user.js file in Chrome and it would prompt you to install the user script. However, in Chrome 21 and up, it downloads the file instead, and displays a warning at the top saying “Extensions, apps, and user scripts can only be added from the Chrome Web Store”. The “Learn More” link points to http://support.google.com/chrome_webstore/bin/answer.py?hl=en&answer=2664769, but that page doesn’t say anything about user scripts, only about extensions in .crx format, apps, and themes. This part sounded interesting: Enterprise Administrators: You can specify URLs that are allowed to install extensions, apps, and themes directly through the ExtensionInstallSources policy. So, I ran the following commands, then restarted Chrome and Chrome Canary: defaults write com.google.Chrome ExtensionInstallSources -array "https://gist.github.com/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://gist.github.com/*" Sadly, these settings only seem to affect extensions, apps, and themes (as it says in the text), not user scripts. (I’ve filed a bug asking to make this setting affect user scripts as well.) Any ideas on how to install a private user script (that I don’t want to add to the Chrome Web Store) in Chrome 21+? Update: The problem was that gist.github.com’s raw URLs redirect to a different domain. So, use these commands instead: # Allow installing user scripts via GitHub or Userscripts.org defaults write com.google.Chrome ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" This works!

  Read the article

• How to connect to local instance of SQL Server 2008 Express

  - by Billy Logan

  I just installed SQL Server 2008 Express on my windows 7 machine. I previously had 2005 on here and used it just fine with the old SQL Server Management Studio Express. I was able to connect with no problems to my PC-NAME\SQLEXPRESS instance. I uninstalled 2005 and SQL Server Management Studio Express. I then installed SQL Server 2008 Express on my machine and elected to have it install SQL Server Management Studio. Now, when I try to connect to PC-NAME\SQLEXPRESS (with Windows Authentication, like I always did), I get the following message: Cannot connect to PC-NAME\SQLEXPRESS. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=-1&LinkId=20476 When I went to the help link it mentions, the help page suggests the following: * Make sure that the SQL Server Browser service is started on the server. * Use the SQL Server Surface Area Configuration tool to enable SQL Server to accept remote connections. For more information about the SQL Server Surface Area Configuration Tool, see Surface Area Configuration for Services and Connections. I did try starting the SQL Server Browser, but don't see that the Surface Area Configuration is installed with this express version. I had seen another user with an almost exact same issue that was missing the database engine on install. If that were the case how could i test for that and where would i go to download that install. Thanks in advance, Billy

  Read the article

• mac terminal run a file of commands

  - by Ilan Tal

  I am coming from Linux and trying to get a Mac to do what I want it to do. The question is what is the best tool to use. I want to mount (unmount) several remote disks. If I go into a terminal I can do the trick by mount -t smbfs //username:pass@addr /Users/me/RemoteDisks/mnt1 Since I want to mount several disks I would like to put all of the information into a file, store it in Documents/subfolder and make a link to it on the desktop (or somewhere better, if there is a better place). At the moment I have manually run the appropriate command in the terminal and the remote disk is mounted and I see its contents. What I need is a one click method to run a file to mount all the disks. I tried Apple script but that didn't like my commands. I don't know exactly what it is expecting to see and perhaps Apple script is the wrong tool. I have no problems in Linux, but the Mac is new to me and I don't know what I should be using. Thanks, Ilan

  Read the article

• Cannot access SMC8014WG-SI provided by TimeWarner/RoadRunner administrative interface...

  - by Matt Rogish

  I just received installation of RoadRunner internet/TV/Voice and I was given a wi-fi router from the TimeWarner folks. The model is a SMC SMC8014WG-SI. Unfortunately, the password it uses is WEP and that is, as we all know, completely insecure. The tech that was here didn't know how to change it to something like WPA2 w/TKIP, and I was on hold for 20 minutes with the TimeWarner folks before I gave up. My problem is that the default web interface (http://192.168.0.1) isn't responding. I can ping it, I can access the internet through it, but I can't get to the admin interface. I did a "hard reset" of the device but still no dice. My suspicion is that the wi-fi admin interface is disabled (a common setting) but the wired interface isn't working on either of my two laptops (I've tried two laptops with two different cables, no link light activated). Am I SOL? Did they lock this down so I can't do what I want to do? Worst-case is I just hook up my go-to WRT54G router to the other modem and leave this one turned off, but I'd rather use their hardware to avoid any "It's not our problem" in the future. Any thoughts? Thanks!!

  Read the article

• Is TrueCrypt truly safe?

  - by Alfred

  Hi. I have been using TrueCrypt for a long time now. However, someone pointed me to a link that described the problems with the license. IANAL and so it really didn't make much sense to me, however I wanted my encryption software to be open source - not because I could hack into it but because I could trust it. Some of the issues with it I have noticed: There is no VCS for the source code. Is this OK? There are no change logs. The forums are a bad place to be. They ban even if you ask a genuine question. Who really owns TrueCrypt? There were some reports of tinkering with the md5 checksums. To be honest, the only reason why I used TrueCrypt was because it was open source. But however, somethings are just not right. Has anyone ever validated the security of TrueCrypt? Should I really be worried? Yes I am paranoid; if I use an encryption software, I trust it with all my life. If all my concerns are genuine, is there any other open source alternative to TrueCrypt?

  Read the article

• The email address used to help trust my PC, is no longer valid, how do I fix that?

  - by Rod

  A few nights ago I upgraded my Windows 7 PC to Windows 8. This morning, when I logged into my PC, I noticed the little flag in the system tray, in desktop mode, had a red "X" on it. I checked it and one of the issues was my needing to tell Windows 8 that I trusted my PC. I clicked on the link to trust my PC, and saw the button to tell it to trust my PC, and so I did. After doing that it send it had sent out an email to a really old email address I had, which hasn't been valid for many years. Now what? Will that "trusting my PC" be invalid, because I can't respond to it (which certainly isn't true, if it's sending messages to so old email address). I didn't even know that Windows still had such an old email address. I'm concerned that I won't have a trust relationship with my own PC, that somehow or other whatever holds onto my information has old information and that I am not sure how to change it in as fast a manner as possible so that I can trust my own PC. How do I do these things?

  Read the article

• Poor Write Performance in VM inside Proxmox PVE 2.0

  - by sorsenne

  I am running a PVE 2.0 on a decent Hardware (2 SATA HDDs as RAID1, 12GB RAM, i7 CPU) but the I/O Performance is very poor inside the VM (Ubuntu 11.10 Server). The very same VM was copied to another Server running simply Ubuntu Server with KVM and had better I/O Perf. this is how the HDD is shown in the Guest: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1.00: ATA-8: ST3000DM001-9YN166, CC49, max UDMA/133 ata1.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC49 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA I tested with DD: $ dd bs=1M count=128 if=/dev/zero of=test conv=fdatasync 128+0 records in 128+0 records out 134217728 bytes (134 MB) copied, 19.2222 s, 7.0 MB/s on the Host, this same Test will result with 156 MB/s in average. PS: I am using VirtIO and see no error in dmesg.

  Read the article

• Problem configuring Apache/Wordpress on subdomain

  - by friism

  I have two servers (one LAMP, one Windows) and one website with an associated blog. I'm running the main site on the Windows server, and the blog on the LAMP server, using Wordpress. The main site is accessed at http://folketsting.dk (it's in Danish -- sorry), the blog is accessed at http://blog.folketsting.dk (this link is bad, read on). The main site works fine. The blog works, except for the frontpage. Example of working post: http://blog.folketsting.dk/2009/10/09/ftlive/. The frontpage of the blog (http://blog.folketsting.dk) shows html from http://folketsting.dk however (except for the css and javascript). In fact, any other URL than the frontpage "works", and gets served by Wordpress e.g. http://blog.folketsting.dk/foo. I cannot -- for the life of me -- understand how the LAMP server running http://blog.folketsting.dk manages to serve up content generated by the Windows server running http://folketsting.dk. Looking at the response headers at http://blog.folketsting.dk, it's evident that the content originates from Apache, not IIS. I'm pretty sure it's not a DNS-issue, since the problem is evident even when accessing the raw IP, eg. http://130.226.142.141/ vs. http://130.226.142.141/foo. I'm thinking it's a bad config in Apache... any clues?

  Read the article

• Ruby on Rails (Redmine) on Apache - 503 Error

  - by andrewtweber

  I am running a Ruby on Rails application called Redmine. It's been working fine, but today it's giving a 503 Service Temporarily Unavailable error. (It was initially set up by an employee who is now gone.) I check the error log and it says: [Mon Nov 21 11:03:30 2011] [error] (111)Connection refused: proxy: HTTP: attempt to connect to 127.0.0.1:3000 (127.0.0.1) failed [Mon Nov 21 11:03:30 2011] [error] ap_proxy_connect_backend disabling worker for (127.0.0.1) Here's a chunk of my Apache config <VirtualHost *:80> ServerName redmine.{domain}.com RewriteCond %{DOCUMENT_ROOT}/%{REQUEST_FILENAME} !-f RewriteRule ^/(.*)$ balancer://redminecluster%{REQUEST_URI} [P,QSA,L] </VirtualHost> <Proxy balancer://redminecluster> BalancerMember http://127.0.0.1:3000 </Proxy> I found this link: http://www.redmine.org/boards/2/topics/20561 which suggests I simply need to "start the redmine server." I've tried /etc/init.d/redmine start which gives me this output => Booting Mongrel => Rails 2.3.11 application starting on http://0.0.0.0:3000 The contents of /etc/init.d/redmine: cd /var/redmine sudo ruby script/server -d -e production One thing I immediately notice is that it says 0.0.0.0 instead of 127.0.0.1. In addition, running top or ps -ef shows no record of a "mongrel" or "redmine" process. I've also tried restarting Apache before and after starting redmine. Not sure where to go from here.

  Read the article

• Member Status: Inquorate in RHEL 5.6

  - by Eugene S

  I've encountered a strange issue. I had to change the time on my Linux RHEL cluster system. I've done it using the following command from the root user: date +%T -s "10:13:13" After doing this, some message appeared relating to <emerg> #1: Quorum Dissolved (however I didn't capture the message completely). In order to investigate the issue I looked at /var/log/messages and I've discovered these errors. Below is the output of few commands I got when tried to investigate the issue, however I don't have enough knowledge to make use of this information. [root@system1a ~]# clustat Cluster Status for system4081 @ Sun Mar 25 11:45:48 2012 Member Status: Inquorate Member Name ID Status ------ ---- ---- ------ chb_sys1a 1 Online, Local chb_sys2a 2 Offline [root@system1a ~]# cman_tool nodes Node Sts Inc Joined Name 1 M 872 2012-03-25 08:43:07 chb_sys1a 2 X 0 chb_sys2a [root@system1a ~]# qdiskd -f -d [17654] debug: Loading configuration information [17654] debug: 0 heuristics loaded [17654] debug: Quorum Daemon: 0 heuristics, 1 interval, 10 tko, 0 votes [17654] debug: Run Flags: 00000035 [17654] info: Quorum Daemon Initializing stat: Bad address [17654] crit: Initialization failed I tried to search through the internet and found out a quite similar issue here. However, for some reason I am not able to access the bug on bugzilla. The link to the bug is here

  Read the article

• How to connect through a proxy using Remote Desktop?

  - by scottmarlowe

  So I've got a home server running Windows Server 2003. I use a dual network card setup and Routing and Remote Access to link the internal, private network to the external connection. The external connection hooks directly to my cable modem (so no routers or other devices sitting between). The problem I'm having is that I can't connect remotely from a location outside the house (so connecting to the server's external connection) to the server using either Remote Desktop or VNC. I have enabled both ports in Routing and Remote Access's firewall to allow access, and I have enabled Remote Desktop in Windows Server 2003. The odd thing is that I can access my home server's SVN repository and I can even ping the server's IP. I am using the IP to attempt to connect, though I use a dyndns.com provided name to connect to my SVN repository, so it shouldn't make a difference (I know the IP is getting resolved correctly). Any ideas on where to start diagnosing this one? I haven't seen anything in my server's event log. If any other info is needed, let me know. Thanks. UPDATE: One last piece of information: We use a proxy server at work, which I'm nearly 100% sure is the culprit. I have a workaround--if I connect to our VPN (even though I'm already inside the building) I am able to connect to my home server. This is with VNC. However, is there a way to connect through a proxy using Remote Desktop? ONE MORE UPDATE: Indeed, it was the http proxy I'm sitting behind at work that was causing the issue. An acceptable workaround is to use my VPN connection to bypass the proxy, and I'm in!

  Read the article

• Google Maps mashup for notes/househunting

  - by afray

  I'm house-hunting at the moment and I'm trying to geek it out er I mean streamline the decision-making process. I'm currently using google maps's "my maps" feature to store pins to properties. I create one map per estate agent, then put relevant into into the individual pins. The idea being, I can look at the map and quickly choose which property to view next. However the pins don't currently link back to the map they're owned by, so you have to hunt a bit to get the estate agent info, it's a hassle to get all maps displayed in a new session if you have lots of agents, and each pin doesn't automatically show its bubble so you have to do lots of clicking to see all the info you want. I've tried Evernote, but despite its tag system initially showing some promise, I can't find a way to seemlessly integrate maps. A few google searches don't turn anything up either. Even the big sites, like http://www.rightmove.co.uk, don't seem to provide any maps integration by default. You can see an individual house's location, but not all results of a search. So is there a web site or windows program I could use to do something like this? Viewing all properties on a map is a must, as is quick access to contact details.

  Read the article

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

< Previous Page | 689 690 691 692 693 694 695 696 697 698 699 700  | Next Page >