Search Results

Search found 20021 results on 801 pages for 'software engeneering learner'.

Page 695/801 | < Previous Page | 691 692 693 694 695 696 697 698 699 700 701 702  | Next Page >

• Data Store/Volume disconnecting. How to resume copy of VMDK?

  - by Serge

  I'm having an issue with my ESXi 4.1 hosts losing the datastore with FC SAN after a power outage. All 3 hosts disconnect so it's definitely a SAN issue. I've tried to resolve the issue on the SAN side with the SAN software support and Adaptec hardware support. No luck there. So I'm stuck with a SAN that will randomly disconnect the volume. I need to get the virtual machines (VMDK files) from the datastore. The problem is I can only get 5-20% before the data store disconnects. I have backups that are slightly older that I can use to replicate the VMDK differences to. What has not worked so far: Powering up the VMs, will boot up for 5-15 minutes then freeze vCenter migrate or clone of VM, will fail after similar period of time vCenter copy/paste of VMDK. Was able to get one 30GB VMDK and no luck after that. vMware Data Recovery. Fails at low %, can't resume, so next backup starts from begining. Veeam Backup & Recovery. Same as above, no resume function. If I can just find a backup solution that will resume from the failed spot that would solve my issue. Anyone have any ideas that I could try? EDIT 1 The SAN is Open-E DSS 6 running on a Supermicro 24 drive enclosure with 4 port Qlogic FC. Adaptec 52445 RAID card.

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• What laptop would be recommended for video-editing or transcoding to blu-ray?

  - by Rob

  I'm looking for a machine (has to be a laptop) reasonably fast enough to handle editing/transcoding/rendering to Blu-ray disc of full true HD 1080p (1920x1080) video from a Samsung R10 camcorder - MPEG4 25fps (not the Sony-Panasonic AVCHD format): To be able to browse through the footage (say, quarter screen is fine for monitoring) and do simple edits - cut out bad bits, add titles, fades, nothing too fancy To be able to burn the footage in 1920x1080p 24p (twenty-four) fps to blu-ray, probably don't mind if I have to leave it for a few hours, or even overnight, as long as its not still running in the morning or takes days. I ALREADY have an external USB 2.0 LG BE06LU10 blu-ray burner. Does quad core make much difference? Or would Dual-core suffice for the above? NVidia because of CUDA for increased speed. What software today can take advantage of this? Which graphics card do I need? So far I've found Dell/Alienware to be well-specified, having a 5yr old Dell laptop that still runs well, albeit slow by today's standards, gives me a good impression. My concerns are too much fan-noise and budget and some Dell Precision Laptops exceed 1500 pounds. Thoughts?

  Read the article

• Share Firefox/Thnderbird data between W7 and Linux Mint 12 in dual boot computer

  - by Albert

  I've just set up my laptop (where I had running only W7) with a dual boot to run Linux Mint 12 as well. I have a "Data" partition (apart from the required partitions for W7 and Linux) where I store pretty much everything that isn't software installations (music, videos, project files, etc). I seem to be able to access that NTFS partition totally fine from Mint (like I've always done with W7), which is cool because I can access all that stuff regardless of which OS I'm using. I would like to know if it's possible (and how) to go one step further and share programs data between the two OS. One example would be my Firefox and Thunderbird data. For example, in Firefox share my bookmarks (and if I could share history, autocomplete and all that stuff, that would be awesome). In thunderbird, be able to share my mail and configuration, seeing the same inbox, folders, message rules, etc... So if I receive/send an email from W7 and later switch to Mint, I can see that email as it had been received/sent from Mint, and vice versa. Is this even possible? Or am I asking for too much convenience? If it's possible, any clues on how to set it all up?

  Read the article

• Setting MSN or Yahoo! Messenger status to Invisible or Offline when idle for an hour

  - by Jian Lin

  Where, or how, do I set it up in MSN Messenger or Yahoo! Messenger to automatically switch my status to either "Invisible" or "Offline" when idle for a half hour, or an hour? I know how to set my status as "Away" or "Busy" after 10 minutes, but can't seem to find a way to set the offline status options without manual intervention. Back story As a software developer, I am very used to turning the computer on for the whole day and not turning it back off. (For example, checking email for urgent fixes, fix issue and push to web server). It's not even turned off when heading to sleep in case I might find it hard to fall asleep and come back to check on the computer. Or to have it there ready in the morning to check that everything is okay. If I'm seen as being online for 24 hours of a day, some people see me as weird. Their perception of my value decreases as I'm always there (hard to get = high value; always there = low value). Leaving it on makes everyone in my contacts list think I have nothing better to do all day than sit in front of the computer. Even though it's my job and I do admittedly spend more time online than other people. That's why I'd like to find a way to set my status as Invisible or Offline.

  Read the article

• Are there any open source reseller packages?

  - by Tom Wright

  My department has just been given the right/responsibility to manage our own VPS. The idea being that the bureaucracy will be less for the many small web projects we run. Since each project will be managed by a different team, I was planning on approaching a shared hosting model. Are there any free pieces of software that would help automate the provision of resources each time a team request a new project? Most of the projects have identical requirements - basically LAMP - so it would be these resources that I would want provisioning (and de-provisioning, if that is a word) automatically. Ideally, there would also be a way to hook it into our LDAP authentication backend too, though I could probably make this sort of modification if necessary. Since we won't be charging our "client" however, we won't need the ability to generate invoices, handle payments, etc. etc. EDIT: Sample workflow Login authenticated against LDAP Username checked against admin group (not on central LDAP) Click 'new project' and enter project name User created on VPS with project name as username Apache virtual host created and subdomain (using project name) allocated FTP & MySQL users created

  Read the article

• What is the best way to create a failover cluster for my IIS website?

  - by ObligatoryMoniker

  Our eCommerce website www.tervis.com currently runs on two servers: SQL server: 2005 x 86 on Windows Server 2003 Standard x86 with a single dual core processor and 4 gb of memeory IIS server: Windows Server 2008 Web edition x64 with dual quad core hyper threaded processors and 32 gb of memory Tervis.com's revenue has steadily grown to the point where we need to have redundant servers deployed with a fail over mechanism so that we do not have any down time. Because the SQL server is so underpowered compared to the web server my thought was to purchase: 2 x SQL Server 2008 R2 web edition x64 single processor license 2 x Windows Server 2008 R2 Web Edition Licenses 1 x New Physical dual quad core 32 GB server 1 x F5 Load Balancer I need the Windows Server 2008 R2 Web Edition licenses so that I can run SQL and IIS on the same box for both of these servers. The thought is to run this as an active/passive fail over cluster that could be upgraded to an active/active cluster if we purchased the additional SQL licensing. The F5 load balancer would serve as the device that monitors the two servers and if the current active one stops responding then fails over to using the other server. To be clear this is not windows clustering but simply using a load balancer to fail over between two computers so that you now have a cluster in the general sense. Is this really the best way to accomplish what I need? Is there some way to leverage the old server 2003 SQL server to function as the devices that funnels http requests to the appropriate active server and then fails over if a problem occurs? Is there any third party clustering software that might help me accomplish this in a simpler fashion?

  Read the article

• tod to avi mpg wmv, convert tod (.mpeg-2) to avi mpg wmv for Movie Maker.

  - by yearofhao

  Need to convert .tod (mpeg-2) to avi mpg wmv download from JVC Everio to PC with tod to avi mpg wmv converter convert tod to uncompressed/raw avi, mpg wmv Have a JVC Everio camcorder? Then you may encounter problems when saving the .tod files to your computer windows movie maker says it can't recognize and edit them to make videos. You may play them using media player but the problem is how to edit them? The bundled software Power cinema could be annoying, since you can only edit when the camera is plugged in to the PC - Power cinema can’t seem to edit from the saved clips alone. So, how do you save them to PC so that you can edit them without the camera and also using windows movie maker? JVC Everio Tod to avi mpg wmv converter costs you a penny to but help you perfectly convert tod file to AVI, MPG, WMV, YouTube FLV, MP4, DV, QuickTime.MOV or other common video formats with fast speed and while keeping the original HD quality. High definition TOD recordings from JVC Camcorders can playback fluidly, convert smoothly and edit professionally on with iOrgsoft TOD file converter iOrgsoft tod to avi mpg wmv Converter has been mostly used by Windows users who use Windows 7 or Vista, after the .tod (mpeg-2 the same codec) downloaded from JVC Everio to PC, it’s best to convert tod to avi, convert to xvid divx, convert tod to uncompressed avi or convert tod to raw avi, tod to mpg, tod to wmv, which are three Windows movie maker best formats to import. TOD to avi mpg wmv converter is a competent video-editing program that allows you to clip/cut TOD video clip, crop the video to encode, and help transfers video to devices like iPhone, iPod, to HDTV connected with Apple TV.

  Read the article

• DLINK WBR-1310B Wireless Router seems to hang...

  - by Ira Baxter

  I have a brand new DLINK-1310B Wireless Router (box never before opened, although I bought it the neighborhood computer junk store). I am using it at home (and in fact am using it this instant from a wireless laptop). When operative, I can ping it at 192.168.0.1, and I can log into it from the PC attached to by LAN and from the wireless PC at //192.168.0.1. In the course of the day since I've installed, it seems to have locked up 3 times. Each time the symptoms are my web browser (or other internet service) stops with a "No internet connection" error. Attempts to contact the router via 192.168.0.1 get no reaction, from either the wireless laptop or from the hardwired PC sitting next to it. It doesn't respond to pings to that address either. Rebooting fixes it. Its brand new. I've seen discussion in other questions about aging cheap electronics. Its too new to be aged. Anyboyd else seen this behavior with a DLINK-1310? Or do I just need to exchange it for another and try again? (I hate rolling dice, I bought the DLINK becuase a previous Linksys died of apparant heating problems). Remarkably, nobody talks about how much software is in a router. Is the stuff just buggy?

  Read the article

• Errors with Using Webcam

  - by C.G.

  I have been having some issues accessing a webcam from my machine. Sometimes (not always) when I run a program that accesses the device (cheese, guvcview, and code using openCV), I get either of two messages, which lead to the program crashing. The first occurs after running the webcam for some time. libv4l2: error dequeuing buf: No such device VIDIOC_DQBUF: No such device The other will occur without even letting me have a chance to run the webcam. libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON - Unable to start capture: No space left on device Occasionally after getting these errors I will also receive a message saying that no such device can be found for subsequent runs. Other than the times that the "No device found" message appears the webcam appears when I use lsusb. My machine runs Linux Fedora 16, and the webcam is a Logitech C920. I do have ffmpeg installed, and I have been able to run the web camera many times in the past without errors. What is particularly puzzling about these errors is that they just sprung up this past weekend. No new software or hardware has been installed on this machine recently; I haven't changed any settings recently either. It could possibly be a driver issue, but I don't know what could have changed which could lead to this issue. Any attempts at researching this problem has been fruitless as this seems to most commonly occur with multiple webcams. I am only working with one device. I'd appreciate any advice for this problem, as this has become a bit frustrating.

  Read the article

• SSH sometimes screws up connection when terminal overflows?

  - by SeveQ

  I've got a problem with SSH on a Debian Lenny based server (it's a vHost within a Xen environment, booted on a Xen kernel). I hope someone can help me with this. The SSH connection seems somehow getting screwed up frequently when the terminal overflows (new lines beyond the bottom of the terminal, usually forcing it to scroll). The connection gets lost but not regularly disconnected. It nearly always happens when I do the following: an existing SSH connection gets disconnected (regularly) I order putty to reestablish the connection login-prompt appears at the very bottom of the putty terminal window I enter my login-name, press the enter key I'm asked for the password, I enter it, press the enter key and BOOM! Nothing more happens. I have to reconnect again. So it is reproducable. I'm not totally sure if the connection crashes before or after I enter the password. Furthermore it also happens when there is much text to be displayed (for example when I compile something or do an ls -l on a directory with many entries). Using 'screen', however, helps to reduces the frequency of occurence but doesn't solve the problem completely. It's occurence is independent from which terminal software I use. I mostly use putty but it also happens with other clients. I certainly hope somebody can help me solving this problem. Thanks in advance! //edit: I've just made a Wireshark trace of the ssh connection and there is nothing, I repeat, nothing different between the working and the failing connection (at least aside from frame numbers, ports and times that obviously can't be equal). This leads me to the assumption that the error has to happen on the server's side.

  Read the article

• Arch Linux: How to handle patches which only you will use?

  - by user12932

  I'm using freerdp together with xmonad and it has been giving me a lot of trouble. The super key (or "windows key") is my mod key in xmonad and it has been interfering with my freerdp usage rather annoyingly. Whenever I switched workspaces (or did anything else in xmonad involving the super key), windows (controlled by the freerdp instance in focus) registered a keypress as well. This event combined with the loss of focus got the super key stuck in windows indefinitely: the press of the keys d and r would first show my desktop, then open the run dialog (as if I was pressing the windows key constantly). I've tried several versions of freerdp, but all exhibited this annoying behavior. So I resorted to patching freerdp myself to just ignore the left super key on my keyboard. I love free software for a lot of reasons (especially the ability to alter things like this myself), however I still find it annoying to patch and rebuild freerdp on all version (and dependency) changes. How do you deal with situations like this? Is there even a "right way" to resolve this issue?

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

• Why can't I connect to my router's config page with Windows 7?

  - by user17940

  I've got a Belkin wireless router, and just bought a new Dell computer with Windows 7 pre-installed. I can connect to the Internet and my home network just fine, but when I try to visit my router's configuration page at http://192.168.2.1, I get a "Connection was reset" error. Nothing I do will make the router's configuration page come up in my web browser. More background information: I could always get to the router's config page from my Windows XP machine. I never had any trouble prior to getting this Windows 7 computer. I can ping 192.168.2.1 successfully from my Windows 7 computer. My PC is connected to the router by a physical CAT5 cable, not via wireless. Every device connected to my router, including the new computer, can get to the Internet with no problem. Here are some things that did not solve the problem: I tried turning off IPV6 in Windows. I tried turning off my firewall and antivirus software I tried using https instead of http I tried disabling and then enabling the network connection in Windows I tried reverting my network card driver back to an older version I have tried both Firefox and Internet Explorer web browsers. Has anyone experienced something like this before, and solved it? Thanks a lot for your help!

  Read the article

• Is USB supported in safe mode on XP?

  - by Hugh Allen

  According Microsoft, "Universal Serial Bus Devices Do Not Work in Safe Mode" under XP. However, in my testing this is incorrect. USB keyboards, mice and flash drives seem to work fine in safe mode (I made sure the BIOS was not providing support). This makes sense because a failure of a standard input device would be, in Microsoft parlance, a "bad user experience". So, Is USB supported in safe mode on XP? If your answer is no (agreeing with Microsoft), please provide a test case, preferably in a virtual machine, where a standard HID keyboard or mouse fails. Please state hardware / BIOS / OS configuration. Note that you will need a PS/2 keyboard attached in addition to your USB device(s) in order to use the boot menu. Virtual machine software usually emulates a PS/2 keyboard. Alternatively, you could add the /safeboot switch to boot.ini. If your answer is yes, please provide a link to some supporting documentation (either from Microsoft or someone authoritative). Your answer might be "devices X, Y and Z are supported but nothing else", in which case also give a link.

  Read the article

• All applications quit when printing on imac OS X 10.5.8

  - by Tamany

  I recently ran a software update. I'm not sure if my problems are associated with this but I'm pretty sure they are as I printed successfully before update. I checked the log at time of printing: 03/05/2010 22:03:15 Microsoft Word[697] *** -[NSCFString _getValue:forType:]: unrecognized selector sent to instance 0x17a82b50 03/05/2010 22:03:15 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:17 [0x0-0x51051].com.microsoft.Word[697] Mon May 3 22:03:17 leopards-imac-2.local Word[697] <Error>: The function `CGPDFDocumentGetMediaBox' is obsolete and will be removed in an upcoming update. Unfortunately, this application, or a library it uses, is using this obsolete function, and is thereby contributing to an overall degradation of system performance. Please use `CGPDFPageGetBoxRect' instead. 03/05/2010 22:22:09 Microsoft Word[697] *** -[NSCFString _getValue:forType:]: unrecognized selector sent to instance 0x1b036500 Any thoughts on how to fix this?

  Read the article

• Mailman delivery troubles

  - by stanigator

  I'm not sure if this is a good place to ask this question. It's about mailing list management software called Mailman from GNU. Here are the details: Hosting provider: Vlexofree Domain: www.sysil.com with Google Apps Mailing List created from hosting cpanel: [email protected] I have registered a list of subscribers, and tried sending an email to [email protected]. I got the following error message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://mail.google.com/support/bin/answer.py?answer=6596 23si6479194ewy.44 (state 14). ----- Original message ----- MIME-Version: 1.0 Received: by 10.216.90.136 with SMTP id e8mr1469147wef.110.1264220118960; Fri, 22 Jan 2010 20:15:18 -0800 (PST) Date: Fri, 22 Jan 2010 20:15:18 -0800 Message-ID: <[email protected]> Subject: From: Stanley Lee <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=0016e6dab0931bccc3047dcd2f1e - Show quoted text - Is there any way of fixing this problem? I would like to be able to have this mailing list to work through my hosting and domain. Thanks in advance.

  Read the article

• unreadable corrupted ntfs partition - lost clusters reported

  - by Eduardo Martinez

  Hi, partition magic is reporting multiple 'bad file record signature' and 'lost clusters' errors on my 250GB samsung sata disk (connected via usb on a xp sp3). Unfortunately PM is unable to fix. PM shows the drive as being NTFS, detects used space ok and also drive name. But PM browser (right click on partition, browse...) won't show anything (as if disk was empty) Windows Explorer is not even picking the drive name and reports 'the file or directory is corrupted and unreadable' PTDD partition table doctor demo tells me the boot sector is fine, and I can see all disk content on its browser - but crucially cannot copy that content over to a new disk (PTDD browser is pretty arid to say the least) Also tried - photorec-6.11.3 - it actually started to extract files but wouldn't keep file names or any folder structure (maybe I missed sth on the configuration options) - find and mount - intellectual scan went well, the only partition on the disk was detected, then tried to mount into p: but got this error on windows explorer: 'p:\ is not accesible. The media is write protected'. Find and mount allows you to create an image from partition but I don't have a disk big enough at hand. Does anyone know if this will keep the extracted files/folders structure intact? I'm starting to think the disk is pretty screwed and my chances to recover this data are slim. Please someone enlighten me with that marvellous piece of software I am missing :-) Thanks in advance

  Read the article

• Looking for a host based network monitor solution

  - by Ole Martin Handeland

  Hi all! Problem So, my hosting company has a network usage graph for my dedicated server. It seems that one day earlier this month, my network usage suddenly spiked with several hundred megabytes transferred (usually it's in the tens, not hundreds). It was probably me, but i just can't be sure who or what it was. Question So my question is; does anyone know of any host based solution for monitoring network usage that would tell me the client's IP-address, the port/service he/she used? What I don't want I'm just guessing that someone will suggest i use nagios, munin, zabbix, cacti, mrtg - I've also looked at those, but a graph over network usage will not give me the answers I'm looking for. :-) Almost there I've already looked at a lot of monitoring solutions, and I've tried [ntop][http://www.ntop.org/], [darkstat][http://unix4lyfe.org/darkstat/] and others. Darkstat just didn't give me the answers. Although it listed a lot of statistics, and i could list the clients - it doesn't show me the network usage for a particular period. Ntop is by far the best I've seen so far - but i think it mostly shows current network usage, not the historical part. I could run apt-get upgrade and download a whole bunch of software, but not see it in the log afterwards.

  Read the article

• Building an Email server for mass emails

  - by EGHDK

  I recently started doing IT odd jobs for a company. The company has a pretty decent sized mail list that costs them over $3000 per month to send out email from. The company is set on creating their own email server so that it can just run and send emails to the client lists. They only send out emails roughly once a month. Has anyone had experience with this? This wouldn't be an email server I guess (as it doesn't need to handle incoming messages) It just has to be able to send around 200,000 emails, once a month. What would be the best way to go about this? Services online like MailChimp have proved to be too pricey. It's not an ad that is being sent out, it's more of a monthly newsletter, so we don't need any crazy software for ROI or anything crazy like that. If I could fit 200,000 people in GMAIL, I'd do it, but I don't think I can (heh... maybe I should try).

  Read the article

• how to block spam email using Microsoft Outlook 2011 (Mac)?

  - by tim8691

  I'm using Microsoft Outlook 2011 for Mac and I'm getting so much spam I'm not sure how to control it. In the past, I always applied "Block Sender" and "Mark as Junk" to any spam email messages I received. This doesn't seem to be enough nowadays. Then I've started using Tools Rules to create rules based on subject, but the same spammer keeps changing subject lines, so this isn't working. I've been tracking the IP addresses they also seem to be changing with each email. Is there any key information I can use in the email to apply a rule to successfully place these spam emails in the junk folder? I'm using a "Low" level of junk email protection. The next higher level, "high", says it may eliminate valid emails, so I prefer not to use this option. There's maybe one or two spammers sending me emails, but the volume is very high now. I'm getting a variation of the following facebook email spam: Hi, Here's some activity you have missed. No matter how far away you are from friends and family, we can help you stay connected. Other people have asked to be your friend. Accept this invitation to see your previous friend requests Some variations on the subject line they've used include: Account Info Change Account Sender Mail Pending ticket notification Pending ticket status Support Center Support med center Pending Notification Reminder: Pending Notification How do people address this? Can it be done within Outlook or is it better to get a third party commercial software to plug-in or otherwise manage it? If so, why would the third party be better than Outlook's internal tools (e.g. what does it look for in the incoming email that Outlook doesn't look at)?

  Read the article

• Saving a file in a CSV type in Excel always removes the BOM

  - by rickp

  I've been trying to find a reasonable solution/explanation (unsuccessfully) to find out why Excel defaults to removing the BOM when saving a file to the CSV type. Please forgive me if you find this a duplicate of this question. This handles reading CSV files with non-ASCII encoding, but it doesn't cover saving the file back out (which is where the biggest issue lies). Here is my current situation (which I'm going to gather is common among localized software dealing with Unicode characters and a CSV format): We export data to a CSV format using UTF-16LE, ensuring the BOM is set (0xFFFE). We validate after the file is generated with a Hex editor to ensure it was set correctly. Open the file in Excel (for this example we're exporting Japanese characters) and witness that Excel handles loading the file with the correct encoding. Attempts to save this file will prompt you with a warning message indicating that the file may contain features that may not be compatible with Unicode encoding, but asks if you'd like to save anyway. If you select the Save As dialog, it will immediately ask you to save the file as "Unicode Text" rather than CSV. If you select the "CSV" extension and save the file it removes the BOM (obviously along with all the Japanese characters). Why would this happen? Is there a solution to this problem, or is this a known 'bug'/limitation of Excel? Additionally (as a side issue) it appears that Excel, when loading UTF-16LE encoded CSV files, only uses TAB delimiters. Again, is this another known 'bug'/limitation of Excel?

  Read the article

• Are there any Graphical PowerShell tools?

  - by Dai

  As a developer for the .NET platform, I like to "explore" a platform, framework or API by browsing through the API documentation which explains what everything is - everything is covered and when I use tools like Reflector or Object Browser then I get to know for certain what I'm working with. When I'm writing my own software I can use tools like the Object Test Bench to explore and work with my classes directly. I'm looking for something similar, but for PowerShell - and ones that avoid text-mode. PowerShell is nice, and there are a lot of cool "discoverability"-things it has, such as the "Verb-Noun" syntax, however when I'm working with Exchange Server, for example, I wanted to get a list of AD Permissions on a Receive Connector and I got this list: [PS] C:\Windows\system32>Get-ADPermission "Client SVR6" -User "NT AUTHORITY\Authenticated Users" | fl User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : True AccessRights : {ReadProperty} IsInherited : True Properties : {ms-Exch-Availability-User-Password} ChildObjectTypes : InheritedObjectType : ms-Exch-Availability-Address-Space InheritanceType : Descendents [PS] C:\Windows\system32> Note how the first few entries contain identical text - there's no way to tell them apart easily. But if there was a GUI presumably it would let me drill-down into the differences better. Are there any tools that do this?

  Read the article

• HOW TO save Contacts from iPhone to Computer?

  - by goodm

  Step 1: Download [b]Tansee iPhone Transfer Contact[/b] free trial version [url="http://softseeking.com/prodail.aspx?proid=47"]here[/url],then install the software (skip if done yet). u can download at:[url="http://www.softseeking.com/prodail.aspx?proid=47"]http://www.softseeking.com/prodail.aspx?proid=47[/url] Step 2: Connect iPhone to your computer. Step 3: Run Tansee iPhone Transfer Contact , your contacts on iPhone memory will display as shown in your iPhone screen automatically as fig 1. Click on single name, all his or her information will display as fig 2 shown. Step 4-a: In fig 1 situation, you can click button "Copy" to copy all contacts from your iPhone to your computer , then select options: 1: Choose File Type: backup to TXT file, ANTC file or CSV file; 2: Choose File Path: You can change the backup path if you do not use default path. 3: Advanced Option: if you choose ANTC format in step 1, you can add a password to protect the file. Note: We do not know the password, so please do remember it. Click OK Button to finish the Copy. See fig 3. Note: You can only copy the first 5 contacts with trail version.[/SIZE] [/SIZE] [size=3][size=3]Step 4-b: In fig 2 situation, click button "Copy Contact From who" to copy contact of a single person, select options: 1: Choose File Type: Backup contacts to TXT file, and CSV file in single contact transfer; 2: Choose File Path: You can change the backup path if you do not use default path; 3: Advanced Option: Disabled in single contact transfer. Click OK Button to finish the Copy. See fig 4. Note: You can only copy the first 5 contacts in trail version.[/size] [/size]

  Read the article

• Sporadic email delivery to one user

  - by minamhere

  I have a user that occasionally does not receive emails from outside our organization. It does not seem to matter whether the other person is replying to an initial email or sending a new message. I have checked the Exchange System Manager and there is no record of the sender at all during this time period. No record of the message getting captured by the spam software (GFI Mail Essentials). The sender does not receive an NDR or any other indication that the message didn't arrive. It seems to me that these messages are not even getting to our servers at all. But, this is only impacting one user(that I am aware of) and not all the time. Some messages get through without any problem, others just disappear. The senders are not related at all. One is in another country, one uses AOL, one uses a corporate Exchange server locally. I can't seem to find a pattern. Where else can I look to try to figure out where these messages are going/getting captured? Are there additional logs that I can enable either within GFI or Exchange that might shed some light on this? Thanks. We are using Exchange 2003 on Server 2003. Desktop client is Outlook 2003 on Windows XP Pro.

  Read the article

< Previous Page | 691 692 693 694 695 696 697 698 699 700 701 702  | Next Page >