Search Results

Search found 28222 results on 1129 pages for 'machine config'.

Page 772/1129 | < Previous Page | 768 769 770 771 772 773 774 775 776 777 778 779  | Next Page >

• Dovecot, POP3 and Gmail

  - by Eric J.

  I setup Postfix and Dovecot on a new Ubuntu box following these directions. From a client machine, I validate that POP3 seems to be working telnet mydomain.com 110 +OK Dovecot ready. USER [email protected] +OK PASS mypassword +OK Logged in. quit +OK Logging out. However, when trying to configure Gmail on the same client to retrieve email via POP3, I get the error Server denied POP3 access for the given username and password. Server returned error: "Login failed." I carefully confirmed that Gmail is configured to use the same POP Server, Port, Username and Password I used when checking the connection with telnet. What could be causing Gmail to get a "Login failed" message?

  Read the article

• Is there anyway to stop Windows 8 from restarting for an update?

  - by William Hilsum

  My Windows 8 machine is going to restart shortly... I have tried a few techniques such as shutdown /a which is not having much luck. Short of pausing the Windows Update service, is there anyway to stop this restart from happening? ---update--- Looks like the "restart" is all talk and no action! The time has gone and I am presented with this: So, it goes along with the top answer here (which I shall shortly accept) --- update again--- It did reset!!! My battery went critical and it turned itself off, I turned it back on (out of suspend) when it was plugged in, I logged in and the first thing it did was automatically restart - closing my open tabs in Chrome :( Oh well...

  Read the article

• Mounting root failed. Dropping into basic maintenance shell

  - by vmsystem

  Hi, I have purchased AMD Phenom X4 955 3.2GHZ processor with supporting gigabyte GA-MA785GM-US2H mother board / 6GB DDR2 RAM / 500GB SATA drive for learning Vmware ESX 3.5 product. In the above configuration, I have installed windows xp 64 bit operating systems and continue to installed vmware workstation 6.5. From the VM workstation, I can able to install ESX3.5 update2, but I unable to start properly, please refer the below mention error. “Mounting root failed. Dropping into basic maintenance shell. To collect logs for VMware, connect a USB storage device and run 'bin/vm-support '. Machine will be rebooted when you exit from this shell.” The same was tested in the windows 2003 Enterprise Edition server / windows 7 32bit / windows 7 64bit also, Please help me to resolve the issue.

  Read the article

• "ssh_exchange_identification: Connection closed by remote host lost connection" when running cron job

  - by grautur

  I have a Ruby script that connects to a remote machine via ssh and executes a command. The script runs fine when I just run it in my terminal. In my crontab, I have 1 * * * * /bin/bash -l -c 'ruby myfile.rb' and if I go ahead and run /bin/bash -l -c 'ruby myfile.rb', everything executes fine. But when cron itself executes the job, I get a ssh_exchange_identification: Connection closed by remote host error. What's the cause of this? How do I fix it?

  Read the article

• Got Samba, Got PyNeighbourhood but still no connection. What else do I need?

  - by Frank A

  I am sure I had already hit post before but then could only find it by backing through browser. Was it deleted? is the question too dumb, sorry that I do not know the right jargon just trying to get answers to my problem anyway have reworded stuff a bit This seems to be a number one requirement for lots of people and 2 months on from setting up my Ubuntu pc, I am still unable to get a lasting connection in either direction. Adding a windows pc to a network is so easy... just a few clicks and get on with using it all. Using all command approaches and modifying configuration files is hardly user friendly. Googling brings up thousands of solutions but mostly they are too techy or assume the user is fully aware of how to use Linux. I do realise that their must be a lot of flavours for connecting to networks. So far I have installed Samba and fiddled with its config file. The day I did all that it worked from XP to Ubuntu. When I came back two days later to transfer my data over it would not connect. Although the the share does show up in Windows (XP) My Network Places. Today I installed PyNeighbourhood and this shows the Ubuntu box and all of the shares I had created at some point on Ubuntu and it even shows this under the XP workgroup name. But instructions on setting the connection up seem to relate to an earlier version and nothing seems to work there either. (I unshared most of those test folders but they still show up her but that is another question. When I click on mount- I can only click on one on the Ubuntu machine, there is one with no name so I assume this to be my attempt to add one XP Shared drive using ipaddress, I get errors. (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", mount error(6): No such device or address Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) OK tried to find the manual referred to... only an old comment that manual would be produced for future versions. I saw in another thread that Winbind is needed as well or at least I assume as well? Totally lost again? Please help, what else needs to be installed to connect to win pcs on the network.

  Read the article

• nginx proxy pass redirect through load balancer

  - by Brian

  I have several backend webservers that are load-balanced using LVS. These machines have only internal non-routable IPs on them. The load-balancer is the only machine with an external IP. This setup works great. I would like to add another webserver for image serving, but it will not be part of the load-balanced pool. Is it possible to proxy pass from the load-balanced web servers to the image server and have the response redirected to the client? Client--external LB--internal web server--internal image server I've gotten proxy pass working when I remove the LB from the equation, but no luck when trying to use it.

  Read the article

• How can I copy the output from a remote command into the local clipboard?

  - by cwd

  I use iTerm2 as my terminal client in Mac OS X. On the local system I can use pbcopy and pbpaste to transfer data between the system clipboard and the terminal, but of course this doesn't work when you're ssh'ed to another machine. Is there some way which I can take the result of a command and copy it to the clipboard automatically? Perhaps an applescript to grab the text on the iTerm windows, then get the next to last line? For instance, if I wanted to copy the current working directory: I run pwd, then use the mouse to select the text, and then press command + c. Is there any better / faster / automatic way of doing this? I'm not looking for a bulletproof solution that would work for every command (eg: might not work when there is a huge scrollback) - I'm just looking for something to make this task that I do quite often a little less tedious. Update I'm looking into using screen to do this, but I'm still not sure if it is possible.

  Read the article

• I have to shard a mysql database. I want to start with 12 shards on 2 machines. What is the best w

  - by Tim

  All tables are InnoDb. I would rather not use mysqldump, because the shard sizes will be about 200 GB (about 700 million rows), and that will take too long. I was hoping to just stop mysql for an hour, copy the data files to a new machine, and start back up. But you can't do this with InnoDb, as some data is in the shared tablespace. Even if I have the innodb_file_per_table option set. This is not a website, but a custom application, used by tens of thousands right now, so uptime and performance are important. I suppose I could add logic into my server application to allow for gradual rebalancing / moving of a shard. Does anyone have a better idea?

  Read the article

• Homegroup and NTFS permissions

  - by bytenik

  I'm running a copy of Windows 7 as a "server" at my home. I have several file shares that I want to make available to specific users only. I've modified the NTFS permissions to only allow these users to access their respective shares. However, while a locally logged on user can access the actual folders just fine, over the network the remote access is authenticating as HomeGroupUser$ rather than the actual user in question, as shown by the Computer Management panel for shares. I do have matching user accounts (i.e. my username locally is abc and a parallel account with username abc and the same password exists on the server machine). I don't want to disable homegroup because there are other shares where homegroup authentication would be desirable, especially for some people where they don't have a parallel account. Is there a way to get the system to authenticate first by matching username, and then by homegroup authentication if there's no matching user?

  Read the article

• Bizarre SSH Problem - It won't even start

  - by thallium85

  I recently got Ubuntu 12.04 Precise, got it up and running with some MediaWiki software, static IP on the box and router and was able to access the main page even from a cell phone. Everything seemed great... Then I wanted to finally get rid of the monitor and keyboard and login remotely via SSH. I installed openssh-server, let everything point to port 22 for a test run and installed putty on my Windows XP machine. I got a connection refused. Went back and started checking the Ubuntu install itself... (I'm under root from this point on) $ sudo -s $ service ssh status ssh stop/waiting $ service ssh start ssh start/running, process 2212 $ service ssh status ssh stop/waiting Apparently ssh has stopped or is waiting for something.... $ ssh localhost ssh: connect to host localhost port 22: Connection refused I can't even connect to myself... I checked ufw (firewall) to see if port 22 is doing alright... $ sudo ufw status Status: active To Action From 22 ALLOW Anywhere 22/tcp ALLOW Anywhere 22 ALLOW Anywhere (v6) 22/tcp ALLOW Anywhere (v6) sshd_config shows only Port 22 Is ssh not using the right IP address at all? I just don't get what I did wrong here. When this is up and running I will def change the port number, but for now, I don't want to mess with the default install too much until a test run with putty is successful. Edit: Here are my sshd_config file and my ssh_config file. The command /usr/sbin/sshd -p 22 -D -d -e returns: /etc/ssh/sshd_config line 159: Subsystem 'sftp' already defined. Edit: @phoibus moving the sshd_config file and reinstalling did the trick! service ssh status the above command shows that ssh is now running and I am now able to log in from my windows xp computer remotely via putty. Thanks so much! I can now use my monitor for other things!

  Read the article

• "Turn Windows Features on or off" when installing .NET 3.5 SP1?

  - by user1413

  I am trying to install a program on my Win7 machine and it says that I need to have .NET 2.0 or later installed. Since Win7 comes with .NET pre-installed, I called support and they told me to just re-install .NET since my .NET install is probably corrupted. The program I am trying to install is SNGWiz (http://www.sngwiz.com/). I do not think its installer is borked. However, when I install .NET 3.5 SP1 using the download from the Microsoft .NET web site, I get the following error: "You must use 'Turn Windows features on or off' in the Control Panel to install or configure Microsoft .NET Framework 3.5 SP1." I have gone to the Windows Features on/off panel and have turned 3.5 both on and off and have tried to re-install .NET 3.5 SP1 under both situations. But it has failed with the same error. What to do?

  Read the article

• CentOS 5 - Unable to resolve addresses for NFS mounts during boot

  - by sagi

  I have a few servers running CentOS 5.3, and am trying to get 2 NFS mount-points to mount automatically on boot. I added 2 lines similar to the following to fstab: server1:/path1 /path1 nfs soft 0 0 server2:/path2 /path2 nfs soft 0 0 When I run 'mount -a' manually, the mount points are properly mounted as expected. However, when I reboot the machine, only /path2 is mounted. For /path1 I get the following error: mount: can't get address for server1 It obviously looks like a DNS issue, but the record is properly configured in all the DNS servers and is mounted properly if I re-try the mount after the reboot is completed. I could properly fix this by using IP address instead of hostnames in /etc/fstab or adding server1 to /etc/hosts but I would rather not do that. What might be the reason for failing to resolve this specific address during boot time? Why the problem is only with the 1st mount point and the 2nd is properly mounted despite having identical configuration?

  Read the article

• identifying windows service

  - by András

  On my win7 machine when I watch a movie in XBMC, once per hour the desktop regains the focus. The movie keeps playing, but in the background now, so I can only hear it. It is quite irritating. I noticed, that the Windows Application log always contains two entres for this time: "The description for Event ID 0 from source Self-service Plug-in cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer." One entry is for starting, and one for stopping 60 seconds later. This keeps repeating, every two starts 3600 seconds apart. How can I repair it? How can I find out which service it is?

  Read the article

• How can I programmatically change the keyboard layout?

  - by Jason R. Coombs

  I want to run a shell command or script that will configure each of my Ubuntu Precise boxes to use the Dvorak keyboard layout as the default (and only) layout. With earlier versions, I was able to set the XKBVARIANT in /etc/default/keyboard but when I make this change in Precise (and reboot), the keyboard layout appears to be unaffected (both in console and in gnome). I tried also setting the XKBMODEL to pc105 and XKBLAYOUT to us, but that did not seem to help. I know I can set the layout for gnome using the 'keyboard layout' tool... but I want the change to affect the console, and I want to automate the process. How can I accomplish this? Edit: To clarify, I want to know how I can cause to change (using only a script or command-line) the keyboard layout to be Dvorak as the default and only keyboard layout for both Gnome and the console. I want this change to be persistent (survive reboots), just as it is when the change is made through the Keyboard Layout tool. Edit: Let me put it another way. If I had installed the operating system myself (which I did not because the OS was installed by the virtual machine infrastructure), I could have selected the desired keyboard layout at install time, and that layout would be applied persistently, system-wide. How can I change the layout to appear as if I had set it during the install process?

  Read the article

• Deploying Office 2013 via GPO

  - by NickC

  Looking at potential ways to deploy Office 2013 via GPO. First and most obvious way is to run a startup script which calls the Office 2013 setup.exe. Problem here is what happens after it is installed, will that startup script keep re-installing the product every time the machine boots? Another potential way is to install each Office component separately using the multitude of .msi files which are present, would that work and provide the same thing as a full install of Office? There is actually twenty three separate .msi files. What about officemui.msi is that a wrapper which contains calls to all of the other office components.

  Read the article

• Why would http & https be blocked, even in safe mode with firewall disabled?

  - by Cogwheel

  I have a windows 7 machine (dell studio xps). Everything on it seems to be in working order. The network device says it has internet connectivity, and indeed I can ping websites, transfer files via ftp, connect to vpns and remote desktop, but the web won't work. I've disabled the windows firewall and still no go. There are no other firewalls installed. The computer came with a trial of norton 360 so I also used the norton removal tool (which solved a similar problem on another computer for me previously). Any thoughts?

  Read the article

• Which free IMAP-supporting webmail would you recommend?

  - by Razor

  Considering a machine with IIS 7.5/PHP 5.2/asp.net and mysql/MSSQL available, which webmail would you pick? Don't think it's relevant but the mail server is installed on localhost, and is hmailserver. If it's one using asp.net it'd be a bonus, but PHP is ok as well and probably offers more choices. "Client side" look and feel definitely needed, flash/silverlight/ajax not a problem. I have also seen this question, but being asked almost 2years ago and being focused on php webmails, I thought that some better option could've been released in the meantime.

  Read the article

• Second display freaks out when waking from sleep

  - by inkedmn

  I have two laptops, an older white MacBook and a brand new Macbook Pro. When either computer is on my desk, I connect it to a second, widescreen display (Acer, a couple years old, uses DVI). The Macbook connects via mini DVI and the MBP connects via mini displayport. When the Macbook is connected and everything goes to sleep, I'm able to wake the machine and both displays in the normal way and everything is fine. Sometimes, when waking the MBP, the laptop and primary display are fine, but the second display shows a bunch of static. If I restart the display, everything's fine. This probably happens 70% of the time when the MBP goes to sleep while connected to this display. Any idea what could be causing this?

  Read the article

• Hosting a web site at home: ISP Blocking port 80?

  - by tombull89

  Hello, I presume this is a better place to put this rather than server fault. I'm interested in setting up a small site to host at home as a "proof of concept" exercise, i.e. to prrove that I know how to do it. I've got a (virtual) server 2003 machine with a site on it, all configured with port forwarding through to 80 on my server. I have a Belkin F5D7634 which I have put my DYNDNS details in but when I try to go to my DYNDNS address it comes up with the page cannot be displayed. My ISP is Carphone Warehouse/AOL and I've been unable to find any information if they block port 80. If they do, can anybody reccomend a home provider that does not block port 80? Regards, Tom.

  Read the article

• IIS not listening over external network, all other traffic working

  - by Beuy

  Hello there, I have a very odd situation, I have a server (let's call it X) running 2008 R2 with two NIC's in it, one is connected to the work domain and has a subnet of 192.168.10.0/24 the other is connected to a ADSL connection and has a subnet of 192.168.1.0/24. The server has IIS installed. On the ADSL connection I have setup a dynamic dns and port forwarding to allow external HTTP, HTTPS, FTP and RDP connections. FTP and RDP are working fine however neither HTTP or HTTPS are working at all. I can browse the websites by going to localhost on the machine, the HTTP and HTTPS ports appear as "Filtered" when I try to scan them using PortQueryUI and browsers respond with a "Server took too long to load or was not responding" error. This was working fine just a few days ago, Windows firewall is disabled I don't have any software firewall on it. And I'm really lost. Any help would be great.

  Read the article

• What is a preferred method for automatically configuring and setting up an Ubuntu instance?

  - by sutch

  I am tired of manually configuring instances of Ubuntu for testing web applications and for setting up workstations. I'm even more frustrated by the issues caused by inconsistent configurations. Is there a method (hopefully not too time consuming to learn and setup) that allows for automation of the setup and configuration of an Ubuntu server or workstation from an ISO. This is primarily for virtual machine instances, but it would be helpful to also create instances on hardware. I am specifically looking for a method to automate the installation of libraries (apt-get), configure services (such as Apache and MySQL), add 3rd party software (download, extract and build), and add libraries to scripting languages (for example, Ruby Gems or CPAN packages for Perl).

  Read the article

• ASP.NET MVC hosting recommendations

  - by chris

  I'm looking for recommendations for hosting an asp.net MVC application. Obviously, we need to be able to have access to configure IIS directly - I'd prefer not to have to go thru a control panel. The web server needs to have a dedicated IP, since some clients will be accessing it via IP. We need at least a SQLServer 2005 database, ideally on the same box. Load and usage will be pretty low, so a virtual machine will probably be fine. Does any one have any recommendations that meet the above constraints?

  Read the article

• Terminal Server/Win2K3: Users can't write to their My Documents or Temp folders

  - by Tim Sullivan

  I have a situation where a bunch of users are running our software on a Terminal Services machine on Windows 2003 Server. I've removed most permissions from the User group, but made sure they all have the appropriate permissions for their own application folders, as well as for their Documents and Settings folder. For some reason, even though everything seems to be set up properly, users can't create or delete files from their My Documents, Temp or other D&S folders. Whatever could be going on? I thought this was going to be straightforward, but clearly it's not! :-) Thanks for any help!

  Read the article

• How can I create a pen drive that I can boot from, and then install Win98 from?

  - by rossmcm

  I have a HP Compaq t5515 thin client computer with a flash disk and USB port. I want to put Win98 onto it, replacing whatever is on there now (I think it is some Linux-based thing). I can find stuff about putting Win98 onto a pen drive and running from that, but I can't find any info about installing Windows 98 from a pen drive onto a sep[arate system. Is it just a matter of making the pen drive bootable to DOS copying the contents of a Win98 installation CD onto the pen drive booting the HP machine from the pen drive running SETUP.EXE from the pen drive? Any pointers appreciated. TIA

  Read the article

• rkhunter warns of inode change by no file modification date changes

  - by Nicholas Tolley Cottrell

  I have several systems running Centos 6 with rkhunter installed. I have a daily cron running rkhunter and reporting back via email. I very often get reports like: ---------------------- Start Rootkit Hunter Scan ---------------------- Warning: The file properties have changed: File: /sbin/fsck Current inode: 6029384 Stored inode: 6029326 Warning: The file properties have changed: File: /sbin/ip Current inode: 6029506 Stored inode: 6029343 Warning: The file properties have changed: File: /sbin/nologin Current inode: 6029443 Stored inode: 6029531 Warning: The file properties have changed: File: /bin/dmesg Current inode: 13369362 Stored inode: 13369366 From what I understand, rkhunter will usually report a changed hash and/or modification date on the scanned files to, so this leads me to think that there is no real change. My question: is there some other activity on the machine that could make the inode change (running ext4) or is this really yum making regular (~ once a week) changes to these files as part of normal security updates?

  Read the article

< Previous Page | 768 769 770 771 772 773 774 775 776 777 778 779  | Next Page >