Search Results

Search found 25093 results on 1004 pages for 'console output'.

Page 802/1004 | < Previous Page | 798 799 800 801 802 803 804 805 806 807 808 809  | Next Page >

• (manually configured) kernel update leaves wireless in a mess

  - by Mala

  I recently upgraded my kernel from 2.6.31-gentoo-r6 to 2.6.32-gentoo-r7. In both cases, I configured everything manually. However, since the upgrade, my wireless card appears to be on the fritz. It will connect to networks just fine, and remain connected, but can only access the internet (and other hosts on the network) for about 3 seconds after connecting. Reconnecting to the network appears to fix the problem... for another 3 seconds or so. The problem is "solved" by booting into the older kernel. The relevant lspci entry is 02:00.0 Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection I'm pretty sure I have the correct drivers enabled in the kernel Device Drivers ---> Network device support ---> Wireless LAN (IEEE 802.11) ---> <*> Intel Wireless Wifi [*] Enable LED support in iwlagn and iwl3945 drivers [*] Enable Spectrum Measurement in iwlagn driver [*] Enable full debugging output in iwlagn and iwl3945 drivers <*> Intel Wireless WiFi Next Gen AGN (iwlagn) [*] Intel Wireless WiFi 4965AGN [*] Intel Wireless WiFi 5000AGN; Intel WiFi Link 1000, 6000, and 6050 Series I tried with the other intel drivers enabled as well (iwl3945) and no difference. Is there something stupid I'm missing? Is there something I have to recompile after upgrading the kernel (a la nvidia)? Thanks Mala

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• ntpdate cannot receive data

  - by Hengjie

  I have a problem where running ntpdate on my server doesn't return any data therefore I get the following error: [root@server etc]# ntpdate -d -u -v time.nist.gov 12 Apr 01:10:09 ntpdate[32072]: ntpdate [email protected] Fri Nov 18 13:21:21 UTC 2011 (1) Looking for host time.nist.gov and service ntp host found : 24-56-178-141.co.warpdriveonline.com transmit(24.56.178.141) transmit(24.56.178.141) transmit(24.56.178.141) transmit(24.56.178.141) transmit(24.56.178.141) 24.56.178.141: Server dropped: no data server 24.56.178.141, port 123 stratum 0, precision 0, leap 00, trust 000 refid [24.56.178.141], delay 0.00000, dispersion 64.00000 transmitted 4, in filter 4 reference time: 00000000.00000000 Thu, Feb 7 2036 14:28:16.000 originate timestamp: 00000000.00000000 Thu, Feb 7 2036 14:28:16.000 transmit timestamp: d3303975.1311947c Thu, Apr 12 2012 1:10:13.074 filter delay: 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 filter offset: 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 delay 0.00000, dispersion 64.00000 offset 0.000000 12 Apr 01:10:14 ntpdate[32072]: no server suitable for synchronization found I have tried Googling the 'no server suitable for synchronization found' error online and I have tried disabling my firewall (running iptables -L returns no rules). I have also confirmed with my DC that there are no rules that are blocking ntp (port 123). Does anyone have any ideas on how I may fix this? Btw, this is what the output should look like on a working server in another DC: 11 Apr 19:01:24 ntpdate[725]: ntpdate [email protected] Fri Nov 18 13:21:17 UTC 2011 (1) Looking for host 184.105.192.247 and service ntp host found : 247.conarusp.net transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) server 184.105.192.247, port 123 stratum 2, precision -20, leap 00, trust 000 refid [184.105.192.247], delay 0.18044, dispersion 0.00006 transmitted 4, in filter 5 reference time: d330364e.e956694f Wed, Apr 11 2012 18:56:46.911 originate timestamp: d3303765.8702d025 Wed, Apr 11 2012 19:01:25.527 transmit timestamp: d3303765.73b213e3 Wed, Apr 11 2012 19:01:25.451 filter delay: 0.18069 0.18044 0.18045 0.18048 0.18048 0.00000 0.00000 0.00000 filter offset: -0.00195 -0.00197 -0.00211 -0.00202 -0.00202 0.000000 0.000000 0.000000 delay 0.18044, dispersion 0.00006 offset -0.001970

  Read the article

• Winamp playing sound but no video

  - by Greg Sansom

  I am having problems playing video in Winamp (the movie I am trying to play is an AVI - not sure if other formats work). I have installed the K-Lite Codec Pack, and the video does work in Winamp Classic. I can also play the video in Winamp on another machine (although I can't remember the exact configuration details of that machine - and I don't think they're relevant). There are a few symptoms: The content of the Video view is either empty, transparent, or displays rendering from other programs. Opening the Visualization view shows the following error: MILKDROP ERROR DirectX initialization failed (GetDeviceCaps). This means that no valid 3D-accelerated display adapter could be found on your computer. If you know this is not the case, it is possible that your graphics subsystem is unstable; please try rebooting your computer and then try to run the plugin again. Otherwise, please install a 3D-accelerated display adapter. Trying to open streams via the SHOUTCast TV plugin shows Error opening video output, and the video does not open. Opening the file with WMC causes the following error (although the movie still plays): Error creating DX9 allocation presenter CreateDevice failed D3DERR_NOTAVAILABLE There are no warnings displayed in Device Manager, although the display adapter is the standard Windows one. Running DxDiag shows no problems (codec for Video listed as XviD 1.1.2 Final). GSpot reports that codecs are installed. System specs: - Windows Server 2008 r2 Standard 64-bit, with latest updates; - .NET 3.5.1 installed; - Winamp v5.6.01 (latest version); - DirectX 11 (Latest version); - K-Lite Codec Pack 7.0.0 (Full); - Machine is HP DC7600 - full specs here. Please comment if there is any more information which will help to diagnose the problem.

  Read the article

• Preventing DDOS/SYN attacks (as far as possible)

  - by Godius

  Recently my CENTOS machine has been under many attacks. I run MRTG and the TCP connections graph shoots up like crazy when an attack is going on. It results in the machine becoming inaccessible. My MRTG graph: mrtg graph This is my current /etc/sysctl.conf config # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 1 # Controls whether core dumps will append the PID to the core filename # Useful for debugging multi-threaded applications kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Controls the maximum size of a message, in bytes kernel.msgmnb = 65536 # Controls the default maxmimum size of a mesage queue kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_syncookies = 1 net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.accept_redirects = 0 net.ipv6.conf.all.accept_redirects = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_source_route = 0 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_max_syn_backlog = 1280 Futher more in my Iptables file (/etc/sysconfig/iptables ) I only have this setup # Generated by iptables-save v1.3.5 on Mon Feb 14 07:07:31 2011 *filter :INPUT ACCEPT [1139630:287215872] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1222418:555508541] Together with the settings above, there are about 800 IP's blocked via the iptables file by lines like: -A INPUT -s 82.77.119.47 -j DROP These have all been added by my hoster, when Ive emailed them in the past about attacks. Im no expert, but im not sure if this is ideal. My question is, what are some good things to add to the iptables file and possibly other files which would make it harder for the attackers to attack my machine without closing out any non-attacking users. Thanks in advance!

  Read the article

• Apache: redirect to https before AUTH for server-status

  - by Putnik

  I want to force https and basic auth for server-status output (mod_status). If I enable auth and user asks for http://site/server-status apache first asks for pass, then redirects to httpS, then asks for pass again. This question is similar to Apache - Redirect to https before AUTH and force https with apache before .htpasswd but I cannot get it work because we are speaking not about generic folder but Location structure. My config (shortly) is as follows: <Location /server-status> SSLRequireSSL <IfModule mod_rewrite.c> RewriteEngine on RewriteBase /server-status RewriteCond %{HTTPS} off RewriteCond %{SERVER_PORT} 80 RewriteRule ^ - [E=nossl] RewriteRule (.*) https://site/server-status} [R=301,L] </IfModule> SetHandler server-status Order deny,allow Deny from all Allow from localhost ip6-localhost Allow from 1.2.3.0/24 Allow from env=nossl AuthUserFile /etc/httpd/status-htpasswd AuthName "Password protected" AuthType Basic Require valid-user Satisfy any </Location> I assume Allow from env=nossl should allow everyone with RewriteCond %{HTTPS} off and server port 80, then force it to redirect but it does not work. Please note, I do not want force to SSL the whole site but /server-status only. If it matters the server has several sites. What am I doing wrong? Thank you.

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

• Creating a pseudoterminal to make sudo happy

  - by larsks

  I need to automate the provisioning of a cloud instance (running Fedora 17) for which the following initial facts are true: I have ssh-key based access to a remote user (cloud) That user has password-free root access via sudo. Manual configuration is as simple as logging in and running sudo su - and having at it, but I would like to fully automate this process. The trick is that the system defaults to having the requiretty option enabled for sudo, which means that an attempt to do something like this: ssh remotehost sudo yum -y install puppet Will fail: sudo: sorry, you must have a tty to run sudo I am working around this right now by first pushing over a small Python script that will run a command on a pseudoterminal: import os import sys import errno import subprocess pid, master_fd = os.forkpty() if pid == 0: # child process: now that we're attached to a # pty, run the given command. os.execvp(sys.argv[1], sys.argv[1:]) else: while True: try: data = os.read(master_fd, 1024) except OSError, detail: if detail.errno == errno.EIO: break if not data: break sys.stdout.write(data) os.wait() Assuming that this is named pty, I can then run: ssh remotehost ./pty sudo yum -y install puppet This works fine, but I'm wondering if there are solutions already available that I haven't considered. I would normally think about expect, but it's not installed by default on this system. screen can do this in a pinch, but the best I came up with was: screen -dmS sudo somecommand ...which does work but eats the output. Are there any other tools available that will allocate a pseudoterminal for me that are going to be generally available?

  Read the article

• Cannot connect to WEBrick on home network

  - by Chris Stewart

  I'm an Android developer and often my applications require server-side code. I typically use Ruby on Rails for the web app, and during development will run the server on my local machine (Mac OS X) with WEBrick. In the morning when I get to the office, I'll run ifconfig in the console to see what IP my laptop has been given that day. I'll use that IP in my Android app when making requests to the web app in question. This all works fine, when I'm in my office. When I get home, I attempt to do the same thing, find my laptop's IP via ifconfig, set it in my app's config file, but the destination can never be found. To exclude my app from the set of hurdles, I attempt to visit the web server IP (e.g., http://192.168.1.4:3000) from my phone's browser, and it cannot connect. If I try from my laptop, which is running the web server, it works fine. If I try from another machine, on the same network, it also is unable to connect. Given this, I think I've narrowed it down to some kind of configuration in my home network, but I frankly have no idea what the cause could be. I don't have anything special at home, your basic Verizon FiOS router/modem with everything connected via Wi-Fi (Wi-Fi for both phone and laptop at work as well, fyi). I've tried disabling the firewall on my Verizon router, enabling port forwarding, and just about everything else I could do for port 3000, and nothing has changed. Dear Server Fault geniuses, please help a poor developer out. :) Edit: Some follow up items to add. My Mac's firewall is not active, and all incoming requests are allowed. I've also verified on my phone and laptop, that they're on the same network (192.168.1.4 Mac, 192.168.1.9 Phone). I have no idea why this isn't working. Edit 2: I went into System Preferences, enabled Web Sharing, and tried to view the website from my phone and it didn't connect. So it's not WEBrick or related to Rails. The firewall on my machine is off and the firewall on my router is off. Edit 3: Some progress. I set up port forwarding for port 3000 to my laptop, found the external IP, and used that and it connected fine. So, there's definitely something not quite set up correctly on my internal network.

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• How to re-add a RAID-10 failed drive on Ubuntu?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• How CPU communicates with HW

  - by b-gen-jack-o-neill

  Good day. I am new here, but I could not find answer to my question using google, so I help I do not violate any rules. So, basically, all I want to ask is, how CPU comminucates with other HW, such as printers, Graphic card, sound card, LAN card etc. I know, that for basic system I/O, you can use BIOS interrupts. INT 10h I believe is for display output. But, what I would like to know is, what actually happens when you execute instruction int 10h. From desription of int instruction, it should jump to routine, which is stored on adress pointed by adress stored in iterrupt table. But how does this routine get into the RAM? Does BIOS save that routines to the RAM? And what actually that routine does? I mean, CPU can only acess RAM, right? So how can now acess some other HW? Is there some special instrucion for it? Or is CPU somehow connected to BIOS, and than BIOS actually does the work? And the last thing, does even OS like Windows or GNU/Linux use BIOS interrupts, or can OS acess HW directly? Thanks.

  Read the article

• compile ntp without ssl

  - by Zulakis

  I need to deploy ntp to a very space-critical pxe-imaging-system. (Yes, each KB matters.) Footprint needs to be as small as possible, so I want to compile ntp without linking openssl. According to the manual this is should be possible: If available, the OpenSSL library from http://www.openssl.org is used to support public key cryptography. The library must be built and installed prior to building NTP. The procedures for doing that are included in the OpenSSL documentation. The library is found during the normal NTP configure phase and the interface routines compiled automatically. Only the libcrypto.a library file and openssl header files are needed. If the library is not available or disabled, this step is not required. I already tried out ./configure --without-openssl however, this didn't help. This is my ldd output: ldd ntpd/ntpd linux-gate.so.1 => (0xb7706000) libm.so.6 => /lib/i686/cmov/libm.so.6 (0xb76d5000) libcrypto.so.0.9.8 => /usr/lib/i686/cmov/libcrypto.so.0.9.8 (0xb7582000) librt.so.1 => /lib/i686/cmov/librt.so.1 (0xb7578000) libc.so.6 => /lib/i686/cmov/libc.so.6 (0xb741d000) /lib/ld-linux.so.2 (0xb7707000) libdl.so.2 => /lib/i686/cmov/libdl.so.2 (0xb7419000) libz.so.1 => /usr/lib/libz.so.1 (0xb7404000) libpthread.so.0 => /lib/i686/cmov/libpthread.so.0 (0xb73eb000) The system I am compiling on is 32-bit debian lenny using openssl 0.9.8g-15+lenny16. What is the correct configure option to compile ntp without openssl?

  Read the article

• Mixed sessions with Classic ASP on IIS 7.5 and Windows 2008 R2 64 bit

  - by Marcin

  Recently had an issues with a server upgrade from IIS 6 on Windows 2003 to IIS 7.5 on Windows 2008 R2 64 bit. We have a number of websites running on Classic ASP. All the sites sit under a particular site, e.g. www.example.com/foo and www.example.com/foobar. On IIS 6 each site was set up as a virtual directory and things worked fine. Since moving to the new set up, a lot of websites seem to have mixed Sessions. To be clear, this is not a app pool recycling issue; rather the sessions are populated with information when the user hits the site and while browsing they get sessions from different sites. We've determined this based on - a few customers called up and reported having their shopping cart with items with names of items belonging to a different site - also our own testing showed that some queries being run would try to bring products in from a different site We've tried - disabling dynamic caching - converting each site to be a virtual application (if I understand correctly, the virtual directory/application concepts were changed/refined somewhat in IIS 7 although to be honest, I'm not clear what the difference is) - various application pool changes (using .NET 2 framework), classic and integrated modes, changing the Process model to NetworkIdentity), all to no avail. The only thing we haven't tried is changing it to run as a 32 bit application. We're not using http only cookies, so when I open up a browser and type document.cookie into the dev console in Firefox/Chrome/IE that there will be multiple ASPSESSIONID=... values whereas previously I believe there was only one. Finally, we use server side JScript for the classic ASP pages, not VBScript, so we have code similar to the below. //the user's login account as a jscript object Session("user") = { email : "[email protected]", id : 123 }; and if we execute a line of code like below: Response.Write( typeof(Session("user")) ); When things are running correctly, we get "object" - as expected. When the Session gets trashed, the output is "unknown" and we are also unable to access the fields within the JScript object (e.g. the .email or .id fields). Much appreciated if anyone can provide any pointers about how to resolve this, everything on google seems to point to different issues.

  Read the article

• apache on Cent OS opening default page on https

  - by Asghar

  I am new to apache and SSL and configuration, i got verysign certificte to secure my site. i have public, private and ca_intermediate cert files. i have configured ssl.conf as below VirtualHost _default_:443> DocumentRoot /var/www/mydomain.com/web/ ServerName mydomain.com:443 ServerAlias www.mydomain.com # Use separate log files for the SSL virtual host; note that LogLevel # is not inherited from httpd.conf. ErrorLog logs/ssl_error_log TransferLog logs/ssl_access_log LogLevel warn # SSL Engine Switch: # Enable/Disable SSL for this virtual host. SSLEngine on problem is that when i access www.mydoamin.com with "HTTP" it works fine, but when i access using "HTTPS" it just opens apache default page. but with green "HTTPS" means my certificates are installed correctly. How can i get rid of this situtaion. Thanks EDIT Output of apachectl -S -bash-3.2# apachectl -S [Mon Aug 27 10:20:19 2012] [warn] NameVirtualHost 82.56.29.189:80 has no VirtualHosts [Mon Aug 27 10:20:19 2012] [warn] NameVirtualHost 82.56.29.189:443 has no VirtualHosts VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: _default_:8081 localhost.localdomain (/etc/httpd/conf/sites-enabled/000-apps.vhost:10) *:8080 is a NameVirtualHost default server localhost.localdomain (/etc/httpd/conf/sites-enabled/000-ispconfig.vhost:10) port 8080 namevhost localhost.localdomain (/etc/httpd/conf/sites-enabled/000-ispconfig.vhost:10) *:443 is a NameVirtualHost default server mydomain.com (/etc/httpd/conf.d/ssl.conf:81) port 443 namevhost mydomain.com (/etc/httpd/conf.d/ssl.conf:81) *:80 is a NameVirtualHost default server app.mydomain.com (/etc/httpd/conf/sites-enabled/100-app.mydomain.com.vhost:7) port 80 namevhost app.mydomain.com (/etc/httpd/conf/sites-enabled/100-app.mydomain.com.vhost:7) port 80 namevhost mydomain.com (/etc/httpd/conf/sites-enabled/100-mydomain.com.vhost:7) Syntax OK

  Read the article

• iptables configuration under ubuntu

  - by aioobe

  I'm following a tutorial on setting up a dns-tunnel. I've run into the following instruction: Now you need to enable forwarding on this server. I use iptables to implement masquerading. There are many HOWTOs about this (a simple one, for example). On Debian, the configuration file for iptables is in /var/lib/iptables/active. The relevant bit is: *nat :PREROUTING ACCEPT [6:1596] :POSTROUTING ACCEPT [1:76] :OUTPUT ACCEPT [1:76] -A POSTROUTING -s 10.0.0.0/8 -j MASQUERADE COMMIT Restart iptables: /etc/init.d/iptables restart The problem is that I don't have any /var/lib/iptables/active. (I'm on ubuntu.) How can I accomplish this? I suspect that I should just interact with the iptables command somehow but I have no clue what to write. Best would probably be if I could put the commands in a script somehow I suppose. (A side-note. If I execute a few iptables-commands it wont be there for ever, right? The rules will be discarded on reboot?)

  Read the article

• What is the difference between these Pentium Extreme Edition CPUs?

  - by Giffyguy

  The CPU in question is the Pentium Extreme Edition 955. Intel's website shows four "versions", but for the most part they all look identical. They even share the same set of ordering codes. But one of them has a substantially lower TDP, which is seemingly unexplainable - since everything else is the same. Two of them say "LGA775, Tray" and I have no idea what "Tray" means either. Also, two of them have a different SPEC code. What I need to know is: What does "LGA775, Tray" mean? Why does the one CPU have a lower TDP? And what does that mean for me? Does that mean lower maximum power consumption? Does it mean the CPU may be more stable/endurant, because of a lower heat output? Why do two of them have a different SPEC code, and what does this mean? Finally, what does PLGA775 (as opposed to LGA775) mean, and do I need to be worried about that? Information from Intel's wbsite: Intel® Pentium® Processor Extreme Edition 955 (4M Cache, 3.46 GHz, 1066 MHz FSB) with SPEC Code 1 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 95 Watts BX80553955 SL94N 2 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL94N 3 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 130 Watts BX80553955 SL8WM 4 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL8WM

  Read the article

• Application runs fine manually but fails as a scheduled task

  - by user42540

  I wasn't sure if this should go here or on stackoverflow. I have an application that loads some files from a network share (the input folder), extracts certain data from them and saves new files (zips them with SharpZLib) on a different network share (output folder). This application runs fine when you open it directly, but when it is set to a scheduled task, it fails in numerous places. This application is scheduled on a Win 2003 server. Let me say right off the bat, the scheduled task is set to use the same login account that I am currently logged in with, so it's not because it's using the LocalSystem account. Something else is going on here. Originally, the application was assigning a drive letter to the input folder using WNetGetConnectionA(). I don't remember why this was done, someone else on our team did that and she's gone now. I think there was some issue with using the WinZip command line with a UNC path. I switched from the WinZip command line utility to using SharpZLib because there were other issues with using the WinZip command line. Anyway, the application failed when trying to assign a drive letter with the error "connection already established." That wasn't true and even after trying WNetCancelConnection(), it still didn't work. Then I decided to just map the drive manually on the server. Then when the app calls Directory.Exists(inputFolderPath) it returns false, even though it does exist. So, for whatever reason, I cannot read this directory from within the application. I can manually navigate to this folder in Windows Explorer and open files. The app log file shows that the user executing it on the schedule is the user I expect, not LocalSystem. Any ideas?

  Read the article

• How to create hash or yml from top level attributes values of node?

  - by Sarah Haskins

  I have a chef recipe where I want to take all of the attributes under node['cfn']['environment'] and write them to a yml file. I could do something like this (it works fine): content = { "environment_class" => node['cfn']['environment']['environment_class'], "node_id" => node['cfn']['environment']['node_id'], "reporting_prefix" => node['cfn']['environment']['reporting_prefix'], "cfn_signal_url" => node['cfn']['environment']['signal_url'] } yml_string = YAML::dump(content) file "/etc/configuration/environment/platform.yml" do mode 0644 action :create content "#{yml_string}" end But I don't like that I have to explicitly list out the names of the attributes. If later I add a new attributes it would be nice if it automatically was included in the written out yml file. So I tried something like this: yml_string = node['cfn']['environment'].to_yaml But because the node is actually a Mash, I get a platform.yml file like this (it contains a lot of unexpected nesting that I don't want): --- !ruby/object:Chef::Node::Attribute normal: tags: [] cfn: environment: &25793640 reporting_prefix: Platform2 signal_url: https://cloudformation-waitcondition-us-east-1.s3.amazonaws.com/... environment_class: Dev node_id: i-908adf9 ... But what I want is this: ---- reporting_prefix: Platform2 signal_url: https://cloudformation-waitcondition-us-east-1.s3.amazonaws.com/... environment_class: Dev node_id: i-908adf9 How can I achieve the desired yml output w/o explicitly listing the attributes by name?

  Read the article

• Not able to access external Hard disk

  - by Jash Jacob

  I have a 1TB External Hard drive which I'm currently not able to access. When I open the External drive in Finder, It shows it's empty. When I use the option to "Get Info", I get the dialog box stating it has about 300GB Free. Tried to get into the External Drive using Terminal, I had no luck. Checking in Disk Utility, It showed that I have many number of files but ZERO folder. I tried to "repair disk", in the process the external Drive got unmounted in between the process. I checked this drive on Windows. I was able to open almost all the folders but I wasn't able to copy anything onto the external drive. One folder caused my windows computer to hang, So i connected the drive back onto my MacBook Pro and tried to access the drive through terminal (this time it worked!) and then I tried to delete the folder with rm command, I got an "input/output error" What should i do to recover the files in that folder? How can i access my external drive on my mac

  Read the article

• NetBackup's bplist doesn't get user/group info for Windows files

  - by Gnustavo

  I'm trying to get information about storage consumption from NetBackup's bplist output. I'm running NBU 6.0MP5 on a RHEL 3 server. The server is backing up several Solaris, Linux, and Windows machines. When I use bplist to get information about files backed up on any UNIX machine I get something like this: # bplist -C unixclient -R 99 -l -s 01/28/2006 -e 01/29/2006 / drwxr-xr-x test ccase 0 Nov 16 09:28 /l/home2/test/ -rw------- test ccase 4737 Jan 06 17:54 /l/home2/test/.bash_history -rw-rw-r-- test ccase 104 Nov 11 2004 /l/home2/test/.bashrc However, when I use it to list files backed up on any Windows client I can't get the user and group information. They both always appear as 'root'. Like this: # bplist -C winclient -t 13 -R 99 -l -s 02/20/2006 / drwx------ root root 0 Feb 20 14:26 /C/temp/ -rwx------ root root 41 Feb 20 14:26 /C/temp/asdf.txt drwx------ root root 0 May 25 2004 /C/temp/CTRMNGR/ Does anyone know why bplist doesn't show the correct user/group for Windows files? If it can't, is there a way to get that information using another command? Thanks. Gustavo.

  Read the article

• Can't Configure IBM 8275-416 Switch Via Serial

  - by Sean M

  I am attempting to configure an IBM 8275-416 switch (I found a manual here) via serial connection. However, when I connect with HyperTerminal, the output contains a lot of garbage characters. It's pretty much unusable, because there's enough layout-breaking text-gunk that it's very difficult to determine what's actually being displayed. . I was able to reset the switch to factory defaults via the terminal interface, so I know that it's not entirely broken. It also performs basic functions all right (i.e., you plug in clients and Ethernet cables - they can connect to clients plugged into other ports) - but I'd like it to do more than that (VLANs yay). I don't know if its in-band UI is operational or not, because I can't get the terminal interface to behave well enough to properly turn on the web/SNMP UI. So that's not available. Things I've tried: - Changing the encoding: HyperTerminal lets me choose between Standard JIS and Shift-JIS. Neither setting fixes the issue. - Checking emulation settings: The manual demands VT100, 19200 baud, 8 data bits, and such: I have faithfully applied these settings, both in HyperTerminal's settings and in the properties of the COM1 port in Device Manager (connecting from a Windows machine). - Restoring to factory defaults: See above. Things that it could be, but that seem unlikely: - Cabling: Couldn't find a proper null-modem cable, so used two 232-to-RJ45 adapters. But if it was a problem with the cable, wouldn't it be more likely to not connect or do input at all, rather than just garble the text? Since I was actually able to perform the reset-to-factory defaults operation, I don't think it's this. - Device as a whole broken: It is a decade and change old, so it's possible that it's just dying slowly. Again, though, it seems like there would be more symptoms than just garbled text in the terminal. What else can I try to get a sane interface to this switch?

  Read the article

• EC2 instances keep becoming inaccessible via SSH, can I use elastic loadbalancer to check SSH connectivity?

  - by Rick

  This is mainly an issue for my development ec2 server as it seems that my instance keeps becoming inaccessible via SSH. It happened yesterday so I killed that one and started a new one and happened again later today. The server still works, my web application is accessible in a web browser but whenever I try to connect via SSH I get a pemrission denied (public key) error message in my terminal. I am 100% sure I am doing nothing wrong as I can create a new instance of the exact same AMI (its a personal custom AMI), change absolutely nothing, including using the same .pem key, and then am able to SSH into that new instance using the exact same command as before (just changing the IP address). I understand that ec2 can have issues but having this happen every day seems a bit odd.. I am using an m2.xlarge instance so I don't know if these tend to be unstable, in the past I have used a small instance and had it running for months with no problems which is why I find this so odd. I am looking into using loadbalancing but it seems the only "health" checks they offer is for http or tcp so I'm not sure if I can make it monitor for SSH connectivity. This is important for development as I may make 1-2 new pushes of an application a day and use SSH to do this. I have a designer that needs to have the app always accessible as he works with the front-end files to test output with the live application. Anyways, any advice / info is appreciated

  Read the article

• Varnish returning 503, FetchError (could not get storage)

  - by Archan

  On the current setup we're running into a problem with Varnish, we're running a CentOS 5.7 x86_64 xenpv, with Cpanel WHM, hosted at VPS.net. Sometimes we will recieve a Guru Meditation from Varnish, and when we look in the varnishlog with the following command varnishlog -d -c -m TxStatus:503 it returns output similar to the following: 15 VCL_call c recv 15 VCL_acl c NO_MATCH devs 15 VCL_return c pass 15 VCL_call c hash 15 Hash c **** 15 Hash c ************* 15 VCL_return c hash 15 VCL_call c pass pass 15 Backend c 12 default default 15 TTL c 1835862523 RFC 0 -1 -1 1332454056 0 1332454055 375007920 0 15 VCL_call c fetch hit_for_pass 15 ObjProtocol c HTTP/1.1 15 ObjResponse c OK 15 ObjHeader c Date: Thu, 22 Mar 2012 22:07:35 GMT 15 ObjHeader c Server: Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 mod_fcgid/2.3.6 15 ObjHeader c X-Powered-By: PHP/5.3.9 15 ObjHeader c Expires: Thu, 19 Nov 1981 08:52:00 GMT 15 ObjHeader c Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 15 ObjHeader c Pragma: no-cache 15 ObjHeader c Content-Type: text/html; charset=utf-8 15 ObjHeader c X-Cacheable: NO:Cache-Control=private 15 FetchError c chunked read_error: 12 (Could not get storage) 15 VCL_call c error deliver 15 VCL_call c deliver deliver As far as I have could gather, we could try increasing the nuke_limit, but currently we have a nuke_limit of 500, and when running varnishstat -1 -f n_lru_nuked we "only" get a total of 1031, even though we have seen the error happen on several pages. When we then run top to see how much memory Varnish is using, it only shows that it is using 763m, although we've set it to be allowed to use 1200m. Any ideas of what the problem can be?

  Read the article

< Previous Page | 798 799 800 801 802 803 804 805 806 807 808 809  | Next Page >