Search Results

Search found 25792 results on 1032 pages for 'map edit'.

Page 816/1032 | < Previous Page | 812 813 814 815 816 817 818 819 820 821 822 823  | Next Page >

• Linux can dual display but windows can't?

  - by Mr_CryptoPrime

  I have two monitors, one that is hdmi-to-dvi and the other vga-to-dvi. I have an AMD HD Radeon 6900 series graphics card installed. I got Ubuntu to display dual monitors, but then I restarted for an update and then Ubuntu wouldn't even boot in recovery mode, it just kept cycling forever...displaying something about "timeout: killing [filepath] [hexadecimal]. So I tried booting into windows (7-professional) and it crashed and displayed this after rebooting: IRQL_NOT_LESS_OR_EQUAL, PAGE_FAULT-IN-NONPAGED-AREA. I went into Bios and reverted to the system defaults and ran system restore and it booted ok, but the dvi-to-dvi monitor would not display. I made sure my drivers were updated and catalyst was updated. Also through research discovered only one is for vga and the other is digital only, so I put the vga-to-dvi in the vga slot and so on. Neither windows or catalyst will detect the dvi-to-dvi montior. Any suggestions? Thanks. EDIT: Found out that booting into Ubuntu with only one monitor (using either monitor with either cable) worked perfectly fine. I could then add another monitor and it displays ok. However, it will, out of the blue, suddenly distort the display. At first I thought the computer crashed, but it is something with the video output from the GPU to the monitor because I pushed the power button and it would refresh every 5secs or so and I could see the "Ubuntu will power down in X seconds", even though it was horribly distorted. Any ideas what's causing this?

  Read the article

• IIS Web Farm Framework servers are automatically set to "unavailable" even when they are healthy... And they never return to the available state!

  - by JohannesH

  I have 2 web farm configurations, one with 2 member servers and one with 3 member servers. I have health monitoring set up on both farms and the monitoring tool reports all servers as being healthy. However after a while all the servers are marked as being "Unavailable" and "Healthy" in the "Monitoring and Management" screen (in the "Servers" screen they are all listed with "Yes" in the "Ready for Load Balancing" column). Viewing the event log on both the web farm controller or any of farm servers doesn't reveal anything interesting. there are no warnings or errors in the period where the servers became unavailable. There are a couple of informational events about the worker process getting shut down due to inactivity but I don't hope this is the cause since that would mean that the farms will die during the night when the load is low. Am I missing something? EDIT: Btw, I think its very odd that the application pool shuts down on the servers since the health monitoring system is polling an aspx page on each server. Shouldn't that keep them going? EDIT2: Now I've also experienced this problem with the RTW version of Web Farm Framework 2.

  Read the article

• The requested operation has failed! (cannot find answer)

  - by Geoff

  I know this problem is plastered all over the web but I've been searching and trying for hours with no luck. Can someone please give me some help? I originally installed Apache 2.0.64 along with PHP 5.2.17, I went through all of the steps in this tutorial with no luck, I found that the culprit was the LoadModule line. After looking on the internet I found a whole bunch of stuff but a lot of it was referring to PHP 5 and Apache 2.2. Since there seemed to be more info on apache 2.2 I removed apache 2.0.64 and installed 2.2. I added the code to LoadModule in the conf file but I got the same problem. I then followed the steps in this tutorial because it was slightly different with some things I hadn't tried yet but still I get the same problem. If I comment out LoadModule... it works fine but otherwise I get "The requested operation has failed!". This is what I ended up keeping since it works only having to comment one line. LoadModule php5_module "c:/php/php5apache2_2.dll" <IfModule mod_php5.c> AddType application/x-httpd-php .php PHPIniDir "c:/php" DirectoryIndex index.php </IfModule> EDIT: How can I stop getting this error message? UPDATE: Also, please note that I took note of the message in the PHP site that stated if PHP 5.2 was to be run with Apache to use the VC6 and not VC9. I had VC9 so I replaced it with VC6, the file is labeled php-5.2.17-nts-Win32-VC6-x86.zip

  Read the article

• Multiple SSL certificates on one server

  - by Kyle O'Brien

  We're hosting two websites on our fairly tiny but dedicated production server. Both website require SSL authentication. So, we have virtualhosts set up for both of them. They both reference their own domain.key, domain.crt and domain.intermediate.crt files. Each CSR and certificate file for each site was setup using its own unique information and nothing is shared between them (other than the server itself) However, which ever site's symbolic link (set up in /etc/apache2/sites-enabled) is reference first, is the site who's certificate is referenced even if we're visiting the second site. So for example, assume our companies are Cadbury and Nestle. We set up both sites with their own certificates but we create Cadbury's symbolic link in apache's site-enabled folder first and then Nestle's. You can visit Nestle perfectly fine but if you check the certificate installation, it reference's Cadbury's certificate. We're hosting these websites on a dedicated Ubuntu 12.04.3 LTS server. Both certificates are provided by Thawte.com. I came across a few potential solutions with no degree of success. I'm hoping someone else has a decent solution? Thanks Edit: The only other solution that seems to have provided success to some people is using SNI with Apache. However, the setups here didn't seem to coincide with our setup at all.

  Read the article

• Server redirect

  - by Tyy

  I have asp.net app XYZ which requires SSL. I am supposed to work with IIS that has only one Web Site - DefaultWebSite - containing multiple apps and virtual directories (3rd party). So, my app is located at domain.com/XYZ. I have to meet these conditions: 1.) requesting DefaultWebSite (domain.com) will run my app. It could redirect to ../XYZ, but I would rather not to. If it has to be done this way, requesting DefaultWebSite or my app over both HTTP and HTTPS will always ends up with redirecting to https://domain.com/XYZ 2.) I can't touch any other apps or virtual directories, can't create additional Web Site, can't set DefaultWebSite to require SSL, ... EDIT: 3.) transmitted data (GET or POST) must be preserved I tried to: set Web Site root directory to my app, but it this caused other apps to crash because of my Web.config (not sure why). set up HTTP redirect on DefaultWebSite to https://domain.com/XYZ. This seems to work correctly, but this doesn't work if user requests my app directly (redirected to domain.com/XYZ/XYZ, or redirect loop). set up Default Document, but this seems to work only if it is located in the Web Site root directory. I know I could write simple .aspx with Response.Redirect, but... is there any better solution? Am I missing something?

  Read the article

• Is there a simple context-menu add-in that could make-up for the Windows-7 status bar deficiency?

  - by DanO

  Edit: I initially asked about free disk space and selected item size. It has since been pointed out that the selected item size summary is still availiable natively in the details pane. I had read elsewhere (wikipedia) that this was removed along with disk free space, which is not the case. Only free disk space has been completely removed. Selection size is still availiable. Is there a context menu add-in out there that could show the free disk space of the relevant drive, when you right click? This would go a long way to compensating for one of the only steps backward I’ve discovered in Windows 7 so far. I doubt anyone had created one specifially for this need before windows 7 because this information was previously easily accessible in the status bar. I thought about creating one, but it has been a while since I have messed with the Shell API, and I know there are coders out there who could do it faster and better. If you’ve heard of one, or know of something else to make-up for this Microsoft misstep, I’d appreciate hearing about it. If MS were listing to the community they would already have a powertoy or add-in of some kind to un-break this. (they could release it unsupported even), as there seem to be many power users that are extremely annoyed by this feature removal decision. If anyone has seen something, please post it here. As it has been only 4 days since official Windows 7 release, I'll wait at least a week to chose an answer. Here's a picture of protoype screenshot: SU question 19232 is related.

  Read the article

• Windows OS level file open event trigger

  - by john

  Colleagues, I have need to run a script/program on certain basic OS level events. In particular when a file in Windows is opened. The open may be read-only or to edit, and may be initiated by a number of means, either from windows explorer (open or ), be selected from a viewing or editing application from the native file chooser, or drag-n-drop into an editing or viewing application. Further, i need the trigger to "hold" the event from completing the action until the runtime on the program has completed. The event handler program may return a pass state, or fail state. If fail state has been returned, then the event must disallow the initially requested action. Lastly, I need to add to the file in question a property or attribute that will contain metadata that will be used by the above event trigger handler program to make a determination as to the pass/fail condition that will ultimately determine if the user is permitted to open the file. Please note that this is NOT a windows event log situation, but one at the OS level file open event. thanks very much for your help. regards, j

  Read the article

• upstart scripts: run a task after networking goes up

  - by The Journeyman geek

  I'm working on moving my current server setup to newer hardware, and migrating from ubuntu karmic koala to lucid lynx. Currently i'm using gw6c (compiled from the gogo6 website, as opposed to the version from the repositories) to get ipv6 access for my systems. On the karmic koala system, i used simple init.d script to get the ipv6 client started #! /bin/sh /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf I figured since this runs at any runlevel, it should translate to respawn console none start on startup stop on shutdown script exec /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf emit free6_ipv6_started end script this works fine started from initctrl, but it apparently fails to start when it boots. - its status being stop/waiting. It works fine (and respawns) when started otherwise.Any ideas on where i'm going wrong, and what would be the appropriate 'start on' arguement? EDIT: the exact error is 'init: gw6c main process (xxx) ended with status 8' followed by the process respawning , with xxx being a PID i suspect. I'm also half suspecting this is cause gw6c starts before networking does, and i need my eth0 up before gw6c is

  Read the article

• Keyboard shortcut for moving a window to another screen

  - by wcoenen

  When working with two (or more screens), a common problem is that launched applications appear on the "wrong" screen. I especially find this annoying when launching a text editor from the command line, because I have to leave the home row with my right hand in order to drag the window to the "right" screen before I can continue typing. Is it possible to define a keyboard shortcut which moves the current application to the other/next screen? Edit: I'm using Windows XP, but it's good to know that the feature already exists in Windows 7. Edit2: I went for the autohotkey script. This adaptation works for me: #q:: WinGetPos, winx, winy,,, A WinGet, mm, MinMax, A WinRestore, A If (winx > 1270) { newx := winx-1270 OutputDebug, Moving left from %winx% to %newx% } else { newx := winx+1270 OutputDebug, Moving right from %winx% to %newx% } WinMove, A,, newx, winy if mm=1 WinMaximize, A Return I did have to make use of the OutputDebug statements and dbgview to discover the proper threshold value 1270 for moving left or right. The exact threshold is especially important when moving maximized windows to the left.

  Read the article

• Routing connections through VPN based on hostname (not IP range)

  - by Michal M

  This bugs me immensly. I need to connect to client's network through VPN. But I definitely do not want to send all the traffic through client's network so this option is out of question. What I need basically is for the OS to know that all client's network subdomains (*.example.com) need to go through the VPN connection. I tried a couple of options: Changing order of services and setting the VPN on top, but this works the same as "Send all traffic over VPN connection". Using "VPN on Demand" option from network advanced options, but this feature is quite rubbish to be honest. Seems to work only in Safari (?!) and it doesn't route the connection, but it basically triggers the OS to connect to the selected VPN. The reason I need it to work based on hostnames rather than IP range is simple - my client has a lot of servers inside his network and it's impossible for me to remember all IPs. They are all within a range, but this doesn't help me remembering. Another option would be to put the VPN connection on the bottom of network services and untick "Send all traffic..." and then put all known hostnames in hosts file, but considering there could be hundreds of servers (therefore hostnames and ips too) it ridiculous job. And if new server appears on the network I'd need to edit the hosts file again. Sisyphean labours. However this works on Windows very simply. If a hostname is not available through default network interface, then it seems to try VPN connection and this works brilliantly. So, how can I achieve that on Mac, then? I know client's internal DNS addresses if that is of any help (like directing a certain domains through a different DNS)? PS. Using latest version 10.6.6. PS2. I am using VPN to access intranet, version control servers (svn://), samba shares and for SSH access to servers.

  Read the article

• Am I obliged to use ipv6 tunnel services if I want to be able to use it?

  - by Zagorax

  I was looking for configuring Slackware to use ipv6 but all instruction I found speak about using an ipv6 tunnel that encapsulate ipv6 request into ipv4 packet and send them to an external router that extracts ipv6 request and sends a reply (or, at least, this is what I understood). Is that necessary? Isn't there a way to configure a pure ipv6 system? If yes, could you please point me to a guide that clearly explain how to enable ipv6 without this trick? I would like to configure my Slackware desktop at first, and then do the same with my Centos server. EDIT: maybe I gave you too few information. Sorry. I'll write some more information thanks to the posted guide. ~$ test -f /proc/net/if_inet6 && echo "Running kernel is IPv6 ready" Running kernel is IPv6 ready So, it seems ipv6 is enabled in my kernel. Some other output from ifconfig, route and /etc/resolv.conf content (with opendns): ~$ /sbin/ifconfig wlan0 | grep inet6 inet6 addr: fe80::21f:3bff:fe60:cc5b/64 Scope:Link ~$ /sbin/route -A inet6 | grep wlan0 fe80::/64 :: U 256 0 0 wlan0 ff00::/8 :: U 256 0 0 wlan0 ~$ cat /etc/resolv.conf inet6 nameserver 2620:0:ccc::2 nameserver 208.67.222.222 nameserver 208.67.220.220 But still, with ping6 I can only ping localhost (::1). Everything else is unreachable. Normal ping works fine. That is why I was asking if I am obliged to use a tunnel.

  Read the article

• Working with an external button box

  - by Scott

  I tried this question on Stack Overflow, but I was pointed here, so here goes: For a new project for myself, I am looking for a way to be able to (for example) open a pop-up window on my laptop, by pressing a button on an external device (to be build by myself, or at least bought) connected with USB. Basically I would be looking at something like a Arduino or Raspberry (IF I am looking in the right direction) with buttons on it, and as soon as I hit a button on the external box with physical buttons, a command activates on my laptop and for example opens a popup window in which I can input tekst. Does anyone know: 1) if it is possible to do this at all. 2) What equipment is needed for the external box, what programming is needed. I preffer .net (dot net) but maybe it can only be done with software from the external box. If anyone can point me in the right direction, like make/model of the external box or websites I would be very happy. I have knowledge of Visual Studio/.net but I am willing to learn other languages if .net is not an option for this project. Thanks in advance Scott PS: If anyone knows of some better tags, or at least knows what I mean and needs me to edit the question, please do tell me... I am new on Stack Overflow/Superuser.

  Read the article

• MAC-Address based routing

  - by d-fens

  Here is what i want to do: I have a bunch of systems, some might have the same Public-IP, i disable ARP. I have a Firewall (either IP Layer or bridge-FW) between these systems and the internet. Depending on the destination port of incoming IP-Packets to some of these Public-IPs i want to set the destinsation-Ethernet-Adress. So for instance System A has IP 8.8.8.8, mac de:ad:be:ef:de:ad, arp disabled System B has IP 8.8.8.8, mac 1f:1f:1f:1f:1f:1f, arp disabled Firewall has IP 8.8.8.1, arp disabled on that interface Incoming packet to IP 8.8.8.8 tcp dest port 100 Incoming packet to IP 8.8.8.8 tcp dest port 101 Firewall sets dest-mac for 1.) - de:ad:be:ef:de:ad Firewall sets dest-mac for 2.) - 1f:1f:1f:1f:1f:1f Second scenario: System A and System B establish outgoing TCP-Connections, and the firewall matches the dst-mac of the incoming IP-Packets (response packets) to the senders-mac address. is this possible in any way with linux and iptables? edit: i read ebtables might "work" in a hackish way for this purpose but i am not sure...

  Read the article

• Port 80 not accessible Amazon ec2

  - by Jasper

  I have started a Amazon EC2 instance (Linux Redhat)... And Apache as well. But when i try: http://MyPublicHostName I get no response. I have ensured that my Security Group allows access to port 80. I can reach port 22 for sure, as i am logged into the instance via ssh. Within the Amazon EC2 Linux Instance when i do: $ wget http://localhost i do get a response. This confirms Apache and port 80 is indeed running fine. Since Amazon starts instances in VPC, do i have to do anything there... Infact i cannot even ping the instance, although i can ssh to it! Any advice? EDIT: Note that i had edited /etc/hosts file earlier to make 389-ds (ldap) installation work. My /etc/hosts file looks like this(IP addresses as shown as w.x.y.z ) 127.0.0.1   localhost.localdomain localhost w.x.y.z   ip-w-x-y-z.us-west-1.compute.internal w.x.y.z   ip-w-x-y-z.localdomain

  Read the article

• Pc sometimes turns on sometimes not

  - by cprogcr

  Some time ago, the PC gave the same problem. It wouldn't turn on. When i pressed the button, it turned on but showed nothing. I had replaced the CPU and that seemed to work. I didn't use the PC that much, rarely you know. But now, after some time, it gives the same problem. It turns on, the front light is on, it makes the normal noise the pc makes when it's turned on , but if I try to shut it down by holding the power button it just doesn't work. So again, I tried replacing the CPU and it worked again. I kept it all day working, just to be sure, and sometimes I would restart it and it would work again. No problems at all. So I turned it off at night, and next morning it just would make the same problem. So I tried replacing the PSU. And it worked again. Now while I had the PC with the new PSU, i tried to insert the old CPU, and again, it would turn on. The same thing, tried restarting too, and it would work. But this morning the same problem happened. Edit: I also tried another CPU today and yet no signs of working. I don't know now what to think.

  Read the article

• How do I tunnel an HTTPS proxy through a virtual machine (VMWare)

  - by Kyle

  I have a personal setup at home using VMWare Workstation. I also have a set of Virtual Private Machines that run Squid, and therefore provide me HTTPS proxy tunnels. Using Proxifier, I can tunnel all traffic for given applications through these tunnels. However, I also have a few virtual machines for dev/staging/experimentation/etc. I generally just use NAT to provide Internet access to the machines, and if I need to use these proxies, I can just setup Proxifier (or a Linux equivalent) to pipe the traffic through them. No problem. But... I got to thinking: Wouldn't it be great if I could assign these proxy tunnels to a virtual machine, so that when I start up the VM, it has instant-on access through the tunnel and not my local connection? (EDIT: Of course, it would USE my local connection, but it would tunnel traffic through the proxy.) To be more clear: I want a solution that binds the proxy to a VM, so that when I start the VM, I don't have to use a proxy client to connect to the tunnel - I am already piping all traffic from that VM through that proxy. I did a bit of searching, and the closest thing I could find was this: How to route public static IP to a virtual machine on a vmware ESXi host? Which wasn't all that applicable. The proxies are protected by user/pass but do not filter by IP. Again, they are HTTPS proxies setup through Squid. Any ideas on how to make this happen? Thanks a ton.

  Read the article

• How to set up multi users on dev server with git and github

  - by Derek Organ

  I'm working on lamp application. We have 2 servers (Debian) Live and Dev. I constantly work on dev main to add new features and fix bugs. When happy all works well I scp the relevant code to the Live system. Database (mysql) is local to each machine. Now this is pretty basic setup really and I want to improve the workflow a bit. I use git and github for version control. Admittedly I've only really used one branch. Their can be 3 different developers who work on the code at different times. We all use the same linux username to connect to the dev server and edit the code directly when needed. I usually then commit and push the code at the end of the day to github. One thing to bare in mind is it isn't easy to run this code on a local machine as there are many apache and subdomain configurations that wouldn't work on a local machine so it is important to work on the dev server not locally. I need to create a new process because we need to have a main trunk now and a branch with a big code re-write. What is the best way to do this. Should I create different unix logins for each developer and set up different working areas on the dev server for there changes? e.g. /var/www/mysite_derek /var/www/mysite_paul /var/www/mysite_mike my thinking is they can do a pull from the main branch and then create there own branch and merge it back in. I'm not sure how this will work though with git locally and with github. will i need to create different github user accounts as well. I'd like to do this the 'right' way and future proof for having lots of potential developers but I also don't want to over complicate it. I simple and elegant solution is preferred. any recommendations or suggestions?

  Read the article

• Make call with alternate provider if NOANSWER

  - by adaptive

  I have two voip providers, one free an the other paid. The free provider only allows local calls to certain area codes, so I need to fall back to the the paid provider if a call fails. At the moment, I have the following context in my extensions.conf file: [globals] ; freephoneline.ca PRIMARY_PROVIDER=fpl ; voip.ms SECONDARY_PROVIDER=voipms [local] exten => _NXXNXXXXXX,1,Set(CALLERID(name)=${OUTGOING_NAME}) exten => _NXXNXXXXXX,n,Dial(SIP/${EXTEN}@${PRIMARY_PROVIDER}) exten => _NXXNXXXXXX,n,Set(CALLERID(num)=${OUTGOING_NUMBER}) exten => _NXXNXXXXXX,n,Dial(SIP/1${EXTEN}@${SECONDARY_PROVIDER}) exten => _NXXNXXXXXX,n,Hangup() I checked the logs and noticed that the free provider responds with NOANSWER if a call is not allowed (Even though it plays a message). What I want is to: Try calling the ${PRIMARY_PROVIDER} first. If NOANSWER is returned by provider (not that the callee did not answer), then call with ${SECONDARY_PROVIDER} How can I modify my dial plan to get the desired results? EDIT : The primary provider is freephoneline.ca, and I'm using asterisk v1.8.2.3-2

  Read the article

• How can I extend / create a new partition from the following setup?

  - by Kiada

  I'm a little unsure what to do in this situation. When I try to create a new simple volume from the unallocated space I get an error because I already have 4 partitions. I have no option to extend either my C:\ primary partition or the E:\ logical drive. C:\ - Gaming Win7 install. D:\ - Storage Unallocated Space - Would somehow like to install OSX on a partition from this space. E:\ - Software Development Win7 install. I:\ - Ignore this. It's an external 1TB HDD. Do I have any options that do not involve formatting / losing information on either C:\ or E:\? Thank you. Link to visual disk partitioning setup image. Edit: A bit more information regarding partitions. Firstly, the image linked above is a screenshot of Windows 7 partitioning tool, easier to read than text I guess! H:\ System Reserved: 100MB NTFS C:\ 244 GB NTFS Healthy (Page File, Primary Partition) D:\ 294 GB NTFS Healthy (Primary Partition) E:\ 100 GB NTFS Healthy (Boot, Page File, Crash Dump, Logical Drive) Unallocated 292 GB Hope this helps :)

  Read the article

• Burning Linux ISO to DVD and making it bootable.

  - by toc777

  Hi everyone, I just downloaded the Fedora 14 Live-Desktop ISO and used CDBurnerXP to burn the image to a DVD. For some reason the first time I burned the image nothing showed up on the DVD when I accessed it even though CDBurnerXP said it had successfully burned to the disk. I did it again and the ISO shows up on the disk (I don't think this is right, should it be the files inside the image that show up on disk or the image file??). The problem now is my dell PC can't find the ISO when I try to boot from it. I get an error saying it can't boot from the CD. I have verified the ISO image as directed from the Fedora website. My question is how do I make a bootable CD from a Fedora Live-Desktop ISO? How can I verify that the ISO was written to the CD correctly and has anyone had any issues booting from a CD using a Dell desktop (I'm not at home at the moment so I can't check what model it is but its old enough, I've had it for about 5 years). EDIT: All that needed to be done was to burn the image to CD as an image and not a data file. The first three times failed, I'm not sure if this was because of faulty DVD's or if the write speed was too high (16x). I put in a new DVD and changed the write speed to 8x, the image was then properly burned to the disk without any errors. Thanks.

  Read the article

• Setting up a server that routes local traffic through vpn, while still being able to access internet directly

  - by Kazuo

  The goal is to setup a local server that routes local traffic through an uncontrolled remote vpn service while still being able to access the internet directly (not tunneled via vpn) and provide services through that direct connection. It is supposed to look like this: http://i.stack.imgur.com/74dGC.png Note: There is another router with modem between the local server and the internet. What is the easiest (best?) way to get this network setup working? I'm planning to setup the connection between the local router and the local server with simple ip forwarding. The problem now is that all the server's traffic is routed through the vpn tunnel as soon as I connect the server's openvpn client to the remote service so there is no direct internet connection available. My first idea was to setup a virtual machine (lxc container or something) and run the vpn client and local networking stuff in the vm. So that the vm receives all the incoming traffic from the local router and tunnels it through the vpn. This, as far as I understand, should not affect the physical server's network connection and should allow it to provide services to the internet. Before I start trying to set this up (I don't have much experience in networking), is there any easier or better way to do this? I would be thankful for every suggestion. Edit: Let's say the interface connected to the internet is eth0 and the interface connected to the local router is eth1. Another idea would be to create a virtual interface eth0:0 and specifiy it as openvpn's local endpoint and then force any traffic coming from eth1 through eth0:0. I'm not sure how I would force the traffic through eth0:0, though (possibly by adding routes).

  Read the article

• newbie: Allow domain users to change power-savings settings

  - by user65007

  I've just recently installed SMS 2011 on a server and added several computers to it's domain. Now I've noticed that I cannot change power settings (even when logged in as user who is in Domain Administrator role, let's call it Admin for future reference). After some googling I ended up adding Admin to the local administrators group using Group Policy Management Editor (as I have no experience in server administration I'm not sure I did it right: I went to Policy Management, selected Forest: xxxxx - Domains - xxxxx - Group Policy Objects - Windows SBS Client - Windows 7 and Windows Vista Policy - go to Settings tab on the right and right-click on anything and select Edit to go to Group Policy Mangement Editor - User Configuration - Preferences - Control Panel Settings - Local Users and Groups - right-click on it and select New - Local Group, then set Action to "Update", Group Name to "Administrators (built-in)", and added Admin to Members). After that I was able to change the power-savings settings on client computers(when logged in as Admin). Now the question: what should I do to allow any domain user to change this settings? Notice, I do not want to force some predefined power plan to all computers, I want to set it up so that any domain user on any client computer would be able to select a different power plan and to make any adjustments to the selected one. Thank you for any suggestions, just keep in mind that I'm newbie (but not completely dumb), so please answer accordingly :)

  Read the article

• How to upgrade iPhone 3G to iOS 5 now that iOS 6 is out? [closed]

  - by mmmshuddup

  My friend has an old iPhone 3G and I wanted to upgrade it to iOS 5 because I had read that the performance is actually better with iOS 5 on that phone in spite of the difference in processor power. The problem is that now that iOS 6 is out, iTunes only gives me the option to upgrade to that. I am a little more leery of iOS 6 knowing that it was launched mostly for the iPhone 5 and since that phone has a way faster processor, I would assume that performance would be an issue on the iPhone 3G. How can I, if possible, upgrade just to iOS 5? Note: I would like to avoid having to jailbreak the phone by all means possible. (It's not mine and I don't want to take the risk with a phone that doesn't belong to me.) EDIT: If anyone knows of a good site to get help on questions like this let me know. Apparently you're allowed to ask questions about iPhones here, just not this. Which is completely utter asinine, but oh well. Anyone with helpful ideas, post in the comments please.

  Read the article

• Directory service unavailiable, new hardware same settings

  - by Alex

  I'm working on a project with 2 sites connected by a VPN. Site 1 has the main server and there is a secondary server at site 2 which I am trying to replace. The current setup works perfectly however I can't for the life of me get the replacement server at site 2 up and running. I'm trying to replace like for like just upgraded hardware. I have installed the OS (all Server 2003 Standard SP2) and used exactly the same settings as the old server. I have setup Active Directory, DNS Server, DHCP Server and WINS Server configured. I have used all the same settings as the old server (except IP address and name). I can access the active directory but I can't do anything; add, edit, delete all returns "the directory service is unavaliable". No-one can login on any of the computers on site 2 and the internet is down. Plugging the old server back in and connecting it to the network rectifies the issue (so both new and old are connected at site 2), everyone can login and the internet is back (curious since the modem connects direct to the switch, and even with the new server online I can connect to the router via IP but not the net). I really don't have much experience but I've been roped into doing this because my company is too cheap to hire a real network admin. Any suggestions of where I can start to troubleshoot this, its driving me crazy and I only have a day before all the users are back on site.

  Read the article

• Vim: How to join multiples lines based on a pattern?

  - by ryz

  I want to join multiple lines in a file based on a pattern that both lines share. This is my example: {101}{}{Apples} {102}{}{Eggs} {103}{}{Beans} {104}... ... {1101}{}{This is a fruit.} {1102}{}{These things are oval.} {1103}{}{You have to roast them.} {1104}... ... I want to join the lines {101}{}{Apples} and {1101}{}{This is a fruit.} to one line {101}{}{Apples}{1101}{}{This is a fruit.} for further processing. Same goes for the other lines. As you can see, both lines share the number 101, but I have no idea how to pull this off. Any Ideas? /EDIT: I found a "workaround": First, delete all preceding "{1" characters from group two in VISUAL BLOCK mode with C-V (or similar shortcut), then sort all lines by number with :%sort n, then join every second line with :let @q = "Jj" followed by 500@q. This works, but leaves me with {101}{}{Apples} 101}{}{This is a fruit.}. I would then need to add the missing characters "{1" in each line, not quite what I want. Any help appreciated.

  Read the article

< Previous Page | 812 813 814 815 816 817 818 819 820 821 822 823  | Next Page >