Search Results

Search found 40998 results on 1640 pages for 'setup project'.

Page 933/1640 | < Previous Page | 929 930 931 932 933 934 935 936 937 938 939 940  | Next Page >

  • Gre Tunnel Cisco Linux traffic forwarding

    - by mezgani
    I setup a gre tunnel a cisco router and a Linux machine, the tunnel interface in the Linux box named pic. Well i have to forward traffic coming from cisco through the Linux box. the rules i've set in the Linux box is described as follow: echo "1" /proc/sys/net/ipv4/ip_forward iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -j ACCEPT iptables -A FORWARD -i pic -o ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i ppp0 -o pic -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE I see the traffic coming from tunnel and forwarded to internet but no reply from sent packet. May i miss something like a routing rule.

    Read the article

  • Can't find instructions how to use Windows 7 drivers on Windows Server 2008 R2

    - by Robert Koritnik
    Windows 7 x64 comes with all sorts of signed drivers so there's high probability that all drivers for your machine will be installed during system setup. On the other hand Windows Server 2008 R2 doesn't. Event though it's practically the same OS when it comes to drivers. I know there's a very good reason for this difference. It's a server product, not a desktop one. But the thing is that many power users and developers use server OS on their workstations which are usually desktop machines (a bit more powerful though) and would benefit from the whole driver spectrum that Windows 7 offers... Question I know I've been reading on the internet about some trick where you first install Windows 7, than do something to get either all Windows 7 drivers or just those installed, and then install Windows Server 2008 R2 and use those drivers of Windows 7. The thing is I can't find these instructions on the internet any more. If anybody knows where they are please provide the link for the rest of us.

    Read the article

  • Can't find instructions how to use Windows 7 drivers on Windows Server 2008 R2

    - by Robert Koritnik
    Maybe I should post this to http://www.serverfault.com. Windows 7 comes with all sorts of signed drivers so there's high probability that all drivers for your machine will be installed during system setup. On the other hand Windows Server 2008 doesn't event though it's practically the same OS when it comes to drivers. But I know that this has a very good reason. It's a server product, not a desktop one. But the thing is that many power users and developers use server OS on their workstations which are normally desktop machines and would need Windows 7 driver spectrum... Question I know I've been reading about some trick on the internet that first installed Windows 7 on the machine, than do something to get either all Windows 7 driver collection or just those installed, and then install Windows Server 2008 and use those drivers. The thing is: I can't seem to find these instructions on the internet any more. If anybody knows where these are please provide the link for the rest of us.

    Read the article

  • How To Temporarily Disable The Touch Screen In X1 Carbon

    - by Daniel Cazzulino
    I know, why would anyone want to do that? Scott properly predicted: Don't knock a touchscreen until you've used one. Every laptop should (and will) have a touch screen in a year. Mark my words. And surely, less than a year later, the X1 Carbon (an amazing ultrabook for sure) has a touch model. And as of today, the price difference for the touch screen is a ridiculous $30 (actually $24 with a “back to school” coupon right now ;)): So why would you NOT get it? I know for some it works great. Now, let’s get real about touch *for a developer* for a minute. About 99.9% of my time in front of my laptop I’m either using Visual Studio or Chrome. I have my hands on the keyboard ALL THE TIME. I use the trackpoint ALL THE TIME. If I want to scroll, I only have to slightly move my fingers. I don’t click around much on pages: I READ them. So, in a few months of using the X1, I think I touched the screen like 10 times, and it was mostly to clear dust, which drives whatever app is in focus crazy. Plus, at home I have this simple setup:...Read full article

    Read the article

  • Postgres 9.0 locking up, 100% CPU

    - by Jake
    We are having a problem where our Postgres 9.0 server occasionally locks up and kills our webapp. Restarting Postgres fixes the problem. Here's what I've been able to observe: First, usage of one CPU jumps to 100% for a few minutes Disk operations drop to ~0 during this time Database operations drop to 0 (blocks and tuples per sec) Logs show during this time: WARNING: worker took too long to start; cancelled WARNING: worker took too long to start; cancelled No Queries in logs (only those over 200ms are logged) No unusually long-running queries logged before or during Then the second CPU jumps to 100% The number of postgres processes jumps from the usual 8-10 to ~20 Matched by a spike in Postgres Blocks per second (about twice normal) Logs show LOG: could not accept SSL connection: EOF detected Queries are running but slow Restarting postgres returns everything to normal Setup: Server: Amazon EC2 Large Ubuntu 10.04.2 LTS Postgres 9.0.3 Dedicated DB server Does anyone have any idea what's causing this? Or any suggestions about what else I should be checking out?

    Read the article

  • Configure FastCGI for Python

    - by Rob
    I have nginx running on a VM and I want to run a Trac site. I need to run a python FastCGI server, but I cannot tell which is the server to use. I have found the following: <a href="http://redmine.lighttpd.net/projects/spawn-fcgi">Lighttpd spawn-fcgi</a> But this seems to require that you compile lighttpd just to get the fcgi server, which is weird. <a href="http://svn.saddi.com/py-lib/trunk/fcgi.py">fcgi.py</a> But this one seems to be depreciated. At the very least it is poorly documented. <a href="http://trac.saddi.com/flup">flup</a> This one comes with dependencies on ubuntu (python-cheetah{a} python-mysqldb{a} python-webpy{a}) that seem unnecessary. Also poorly documented. Are their any recent guides for setting this up. Trac's own FastCGI setup page seems to miss some steps.

    Read the article

  • SMTP server on Win2008, SPF ecc

    - by Ronnie
    I want be able to send outgoing email from my website. I want to setup Win2008 smtp to be able to send them respecting all the spam rules. My checklist is: the smtp should be able to accept outgoing email only from internal sites: I will limit it to relay only 127.0.0.1 is this correct? it should have set SPF, DKIM and all the policy avaiable to not be marked as spam: how you would configure it for the internal SMTP? Should I use another kind of server like hMail server? I should be able to send like 30 email from each user session on the website without obliging the user to wait that the email is effectivly sent (I thought to save it on a folder and then use a batch to send them asynchronously). What are my options? What other steps would you add to be sure that the outgoing email is not marked as spam?

    Read the article

  • How did I get here? My route to Android, iPhone, Windows Phone 7, and interest in Mobile Devices

    - by Wallym
    I get asked all the time how/why I got interested in mobile and jumped on this fairly early.  I tend to give half answers because it wasn't just one thing that took me to mobile, but a whole host of separate ivents culminating in a specific event where I wasdoing market research in May/June 2008.  Let me throw out the events and the facts about me: I tend to like new, different, cool stuff.  I jumped on .NET early on.  I jumped on Ajax early on.  I don't jump on every new technology that comes down the road, I'm probably the only person on the planet that doesn't "get" MVC, though I acknowledge that a lot of people do and it solves a number of problems in the default settings of ASP.NET WebForms. I remember buying an early Windows CE device. It was interesting, but dang, this stylus thing sucks. After I lost my third stylus, i just gave up.  I got my first mobile phone in early 1999.  Reception was crappy, but I could see the value in being mobile. In 1999, I worked on a manufacturing systems project.  One piece of the projects was a set of handheld devices on the shop floor.  While the UI was a crappy DOS based, yes I said DOS as in Disk Operating System Version 6.22, I could see that the wireless world was a direction I wanted to be in. In 2000, Microsoft released the first public alpha of .NET.  Very cool stuff indeed.  One piece of the puzzle was a set of mobile controls for ASP.NET.  I build numerous test apps as well as mobile version using these mobile controls.  Now, the mobile UIs of the time were based on WML, which was crap. I could real all the analysis of mobile and read all about growth rates.  Now, you have to realize that growth rates can be impressive when dealing with small numbers, but I knew it was a comer. In our first book, I got talked out of mobile because of the line from the publisher "Wally, mobile doesn't sell." Blackberry was the dominant device of the mid 2000s.  Its users were referred to as "Crackberry addicts."  Unfortunately, the mobile development experience for native apps was crap and the web experience was fairly rough as well, but if they could get the ecosystem started, other phones and better blackberryies would come out.  I finally jumped into using a blackberry. Sometime around 2006, I heard "Wally, mobile doesn't sell" again.  Now, anyone that knows me knows that someone saying something like this to me means I'll keep trying it. The phones of the mid 2000s were moving to be more graphical, but there were too many that had this idea that they had to use a stylus.  Stylus suck.  They get lost too easily. I worked on a project in 2007 and 2008 for a startup trying to answer the question of "What is there to do where I am at?"  For some reason, they wanted to be tied to PCs.  As it became obvious that they were having problems, their investor asked us to do some market research and to figure out what the marketplace did want.  One of the important things that I figured out was the we lived in a mobile world and if you had a mobile app, it need to be on a mobile device, not tied to a desktop/laptop/netbook device.  If there was any single event, this was it - I was doing some market research and sat and talked to people in a bar/restaurant in Atlanta called "The Grove" on Lavista.  The consensus of the people that I talked to was that they wanted their data where ever they were at, laptop, pc, mobile, whereever. In 2007, Apple released the iPhone.  Wow, what an impressive device, even with all the problems of a 1st generation device.  I bought an iPod Touch 1st generation to understand touch better, one of the best decisions I ever made. I decided in late 2008, to make a move into cloud, for a number of reasons.  I was working on an example app.  In April, 2009, one of my friends at Microsoft said "don't mention my name with this, but you need an iPhone front end for this app."  How do you get on the iPhone.  Well, there are a number of ways including: ObjectiveC.  Its hard to teach an old dog new tricks, and this dog knows .NET, not ObjectiveC. HTML, web, javascript optimized interface.  yeah, this is possible. PhoneGap.  Now, this is interesting, take an html interface and get it to run on the iPhone, Android, Blackberry, and other platforms.  I thought that this way made the most sense for me until......... MonoTouch.  In May/June 2009, Novell announced a way for .NET/c# developers to write apps for the iPhone.  This is the way that made the most sense to me. Titanium by Appcelerator.  This is similar in concept to PhoneGap.  I haven't played with this much but do want to learn more about it. In July, 2009, I emailed one of my contacts at Wrox to see if they would be interested in a short MonoTouch ebook in their Wrox Blox format.  I fully expected another  response along the lines of "Wally, mobile doesn't sell."  The response I got was "Wally, iPhone is H O T, get started immediately, can you have this to me before Labor Day."  Not quite the response I expected.  Thankfully, we didn't make the Labor Day, first draft date. I kept pushing back because I had a feeling that things were not going to be quite as polished and feature rich as necessary.  After all, Novell doesn't have the resouces of Microsoft's developer division. The ebook shipped on November 30, 2009. On about December, 15, 2009, my editor emailed and said "Your ebook is selling really well, lets do a full book and it by March 1 so get started."  Thankfully, guys like Craig Dunn and Chris Hardy were interested along with Martin and Ror joinged us later on. I bought my wife an iPhone 3Gs in early 2010 to go along with all my iPod Touch devices. I tried to pretend in 2010 that I wasn't that interested in mobile and still had interest in the desktop technologies.  I love the technologies and continue to use them today, but that isn't where my interest is right now.  I'm just about all mobile all the time with my energies.  Our book shipped in the beginning of July, 2010 right in the middle of the Apple FUD.I've been looking at Mobile Web as a way around the AppStores and Apple FUD problems of 2010. With all the Apple self FUD, we became interested in Android.I went up to Dino Esposito at DevConnections in Las Vegas at introduced myself. I've always tried to keep up with what Dino has been doing. I was shocked, he wanted to meet me.  We must have talked for 1.5 hours. It was way more time than I deserved. If you get a chance, go and introduce yourself to Dino. He's a great guy. Microsoft released Windows Phone 7 in the Fall of 2010.  I'm not doing development on that platform at this time.  I think they have a very interesting user interface.  The devices are being positively reviewed.  For my purposes, the devices are limited at this point in time.  We'll see what 2011 brings as far as updates to the operating system.  I need multitasking/background processing and html5 in the browser. Add that as well as acceptance in the marketplace and I'll be more interested in the device. Obviosuly, I'm now working on a MonoDroid book . I own Android and iPhone/iOS devices.  I am currently working on some startup ideas and am exploring as much in that area as I can. For 2011, I'm planning on speaking at Android Developer's Conference (AnDevCon) and Mobile Connections.  I'm really excited about this. I have a couple of magazine articles coming out in 2011 on Android and iPhone development with the Mono technologies.is Mono "The Answer"? What's "The Question?" I think it will work for me.  It might work for you, it might not.  it depends on your situation.  Its the current horse that I am riding. I might find a better horse tomorrow. So, that's how I got here.  I'm in love with mobile.  Mobile native apps on the device as well as mobile web.  I'm into all this cool stuff.  Where are you at?

    Read the article

  • Creating Java Neural Networks

    - by Tori Wieldt
    A new article on OTN/Java, titled “Neural Networks on the NetBeans Platform,” by Zoran Sevarac, reports on Neuroph Studio, an open source Java neural network development environment built on top of the NetBeans Platform. This article shows how to create Java neural networks for classification.From the article:“Neural networks are artificial intelligence (machine learning technology) suitable for ill-defined problems, such as recognition, prediction, classification, and control. This article shows how to create some Java neural networks for classification. Note that Neuroph Studio also has support for image recognition, text character recognition, and handwritten letter recognition...”“Neuroph Studio is a Java neural network development environment built on top of the NetBeans Platform and Neuroph Framework. It is an IDE-like environment customized for neural network development. Neuroph Studio is a GUI that sits on top of Neuroph Framework. Neuroph Framework is a full-featured Java framework that provides classes for building neural networks…”The author, Zoran Sevarac, is a teaching assistant at Belgrade University, Department for Software Engineering, and a researcher at the Laboratory for Artificial Intelligence at Belgrade University. He is also a member of GOAI Research Network. Through his research, he has been working on the development of a Java neural network framework, which was released as the open source project Neuroph.Brainy stuff. Read the article here.

    Read the article

  • XAMPP - allow internet connection

    - by user1645034
    I usually do my web dev on a production server, now i need to bring some work at home. I have installed XAMPP on my laptop and it seems to work perfectly fine. Most of my project involves CURL enabled, I need to make my xampp application to access the internet. Perhaps give it some IP address and Gateway. I've seen documentation how to enable CURL on xampp, yet I'm struggling to find how to make XAMPP to have internet access. I'm not asking how to access my XAMPP remotely, I'm simply asking how to give internet connection to xampp application for my CURL and other social network API to work.

    Read the article

  • Using DNS in iproute2

    - by Oliver
    In my setup I can redirect the default gateway based on the source address. Let's say a user is connected through tun0 (10.2.0.0/16) is redirect to another vpn. That works fine! ip rule add from 10.2.0.10 lookup vpn1 In a second rule I redirect the default gateway to another gateway if the user access a certain ip adress: ip rule add from 10.2.0.10 to 94.142.154.71 lookup vpn2 If I access the page on 94.142.154.71 (myip.is) the user is correctly routed and I can see the ip of the second vpn. On any other pages the ip address of vpn1 is shown. But how do I tell iproute2 that all request at e. g. google.com should be redirected through vpn2?

    Read the article

  • how do you set the admin password on openldap 2.4

    - by dingfelder
    I am getting started with openLdap 2.4 and am having a bit of trouble, all the examples I see seem to refer to previous versions which used the text config file slapd.conf but from what I see on discussions about v2.4, this has been deprecated. I thought prehaps I needed to add a user, and log in as them but when I try and run an ldapadd command, I get a prompt to enter a password: Enter LDAP Password: ldap_bind: Invalid credentials (49) Notes: I installed openldap server via yum (in fedora 15), and have installed phpldapadminbut also can try things on the command line if anyone has suggestions. After installing and starting I get the following response from a search: # ldapsearch -x -b '' -s base '(objectclass=*)' namingContexts # extended LDIF # LDAPv3 # base <> with scope baseObject # filter: (objectclass=*) # requesting: namingContexts dn: namingContexts: dc=my-domain,dc=com # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 I am glad to remove and reinstall the server if that helps, can anyone provide a link to tips that works for version 2.4 for a new setup?

    Read the article

  • Proxy via Telnet

    - by Vreality2007
    I know telnet is insecure and all, but I'm stuck using it because ssh is blocked. I know how to setup ssh to bind the connection to a local port, is there a way to do this with telnet? For example, if I am using an ssh connection, I would bind it to port 999 like this: ssh -D 999 [email protected] -N -C I've tried using the -b command in linux, but to no avail. Is this even possible? This is what I've tried: telnet host.com -b 999 I'm sorry if the answer is obvious, but I've done a lot of research and testing and I can't seem to figure this out. NOTE: I plan on telling the admin if I can find a way to get this to work, this is based off of simple curiosity and not malicious intent. If I can't bind a telnet port, is there a way to tunnel an ssh connection through telnet?

    Read the article

  • Microsoft SQL Server 2012 Analysis Services – The BISM Tabular Model #ssas #tabular #bism

    - by Marco Russo (SQLBI)
    I, Alberto and Chris spent many months (many nights, holidays and also working days of the last months) writing the book we would have liked to read when we started working with Analysis Services Tabular. A book that explains how to use Tabular, how to model data with Tabular, how Tabular internally works and how to optimize a Tabular model. All those things you need to start on a real project in order to make an happy customer. You know, we’re all consultants after all, so customer satisfaction is really important to be paid for our job! Now the book writing is finished, we’re in the final stage of editing and reviews and we look forward to get our print copy. Its title is very long: Microsoft SQL Server 2012 Analysis Services – The BISM Tabular Model. But the important thing is that you can already (pre)order it. This is the list of chapters: 01. BISM Architecture 02. Guided Tour on Tabular 03. Loading Data Inside Tabular 04. DAX Basics 05. Understanding Evaluation Contexts 06. Querying Tabular 07. DAX Advanced 08. Understanding Time Intelligence in DAX 09. Vertipaq Engine 10. Using Tabular Hierarchies 11. Data modeling in Tabular 12. Using Advanced Tabular Relationships 13. Tabular Presentation Layer 14. Tabular and PowerPivot for Excel 15. Tabular Security 16. Interfacing with Tabular 17. Tabular Deployment 18. Optimization and Monitoring And this is the book cover – have a good read!

    Read the article

  • Leaving Microsoft

    - by Stephen Walther
    After two and a half years working with the ASP.NET team, I’ve decided that this is the right time to leave Microsoft and, with the help of some friends, re-launch my ASP.NET training and consulting company. The company has the modest name Superexpert. While working on my Ph.D. at MIT, I was surrounded by professors and students who were passionate about knowledge. During the Internet boom, I was lucky enough to work side-by-side with some very smart and hard-working people to create several successful startups. However, the people I worked with at Microsoft were among the smartest and hardest working. Microsoft hires a small number of people and gives them huge responsibilities. It continues to amaze me that so few people work on the ASP.NET team when you consider how much the team produces. I had the opportunity to work with a number of inspiring people at Microsoft. I’ll miss working with Scott Hunter, Dave Reed, Boris Moore, Eilon Lipton, Scott Guthrie, James Senior, Jim Wang, Phil Haack, Damian Edwards, Vishal Joshi, Mike Pope, Jon Young, Dmitry Robsman, Simon Calvert, Stefan Schackow, and many others. I’m proud of what we accomplished while I was working at Microsoft. We reached out to the jQuery team and changed direction from Microsoft Ajax to jQuery. We successfully contributed several important new features to the open-source jQuery project including jQuery Templates, jQuery Data-Linking, jQuery Globalization, and (as John Resig announced at the last jQuery conference) jQuery Require. I’m looking forward to returning to training and consulting. We want to focus on providing consulting on the “right way” of building ASP.NET websites, which we call Modern ASP.NET applications. By Modern ASP.NET applications, I mean applications built with ASP.NET MVC, jQuery, HTML5, and Visual Studio ALM. Additionally, we want to help companies that have existing ASP.NET Web Forms applications migrate to ASP.NET MVC. If you are interested in having us provide training for your company or you need help building a custom ASP.NET application then please contact us at [email protected] or visit our website at Superexpert.com.

    Read the article

  • OpenVPN vs. IPSec - Pros and Cons, what to use?

    - by jens
    interestingly I have not found any good searchresults when searching for "OpenVPN vs IPSec": I need to setup a private LAN over an untrusted network. And as far as I know, both approaces seem to be valid. But I do not know which one is better. I would be very thankfull If you can list the pro's and con's of both approaches and maybe your suggestions and experiences what to use. Update (Regarding the comment/question): In my concrete case the goal is to have any number of Servers (with static IPs) be connected transparently with each other. But a small portion of "dynamic clients like road warriors" (with dynamic IPs) should also be able to connect. The main goal is however having a "transparent secure network" run top of untrusted network. I am quite a newbie so I do not know how to correctly interprete "1:1 Point to Point Connections" = The solution should support Broadcasts and all that stuff so it is a fully functional network... Thank you very much!! Jens

    Read the article

  • Couldn't find package - But package is listed in the Packages file

    - by Chris
    (Quoted items are redacted elements) I am using a private repository and an currently trying to repackage some packages 3rd-party packages. I extract the package, make a few modifications (just the control files to fit with company policy - though sometimes file install locations though not in this case) and repackage (and usually rename). Normally I copy the files into a new blank debhelper project and reconstruct the package, however, with a recent one I attempting to convert and some libraries and stuff aren't linking properly (I did copy the postinst, postrm, and preinst files along with all DEDIAN files exactly), the original package worked, but my repackage doesn't, despite providing the same files in the same locations and the same postinst and preinst. So I was attempting to just modify the current packages control files (as the original package is not very good and will not list in our repository and getting a better one from the 3rd party is not an option). I also renamed the package. I did the following: dpkg-deb -R "directory" Modify DEBIAN/control dpkg-deb -b "directory" "package name I want" I did this and put it in our repository. The package shows up in the "Packages" file on the repository and running apt-get update on the client side shows the package in: /var/lib/apt/lists/"server"_"location"_Packages However when I do an apt-get install on the package name (as listed in the Packages file - I did a copy paste) it says it can't find the package. Same with an apt-cache search The Packages listings is as follow (name redacted): Package: "package name" Priority: extra Section: unknown Maintainer: "maintainer" Architecture: any Version: 1.0-lucid5 Depends: libc Filename: "directory"/"package_filename" Size: 2206292 MD5sum: "md5sum" SHA1: "sha key" SHA256: "sha256 key" Description: "description" I am running as sudo (and tried as root as well). I don't understand why apt-get won't see the package. Can you point out any flaws in what I have done, or perhaps some help on getting apt-get to properly see the package. Or perhaps an alternative. I am not even sure if this is a valid way to repackage something. Thanks.

    Read the article

  • A dacpac limitation – Deploy dacpac wizard does not understand SqlCmd variables

    - by jamiet
    Since the release of SQL Server 2012 I have become a big fan of using dacpacs for deploying SQL Server databases (for reasons that I will explain some other day) and I chose to use a dacpac to distribute my recently announced utility sp_ssiscatalog (read: Introducing sp_ssiscatalog (v1.0.0.0)). Unfortunately if you read that blog post you may have taken note of the following: Ordinarily a dacpac can be deployed to a SQL Server from SSMS using the Deploy Dacpac wizard however in this case there is a limitation. Due to sp_ssiscatalog referring to objects in the SSIS Catalog (which it has to do of course) the dacpac contains a SqlCmd variable to store the name of the database that underpins the SSIS Catalog; unfortunately the Deploy Dacpac wizard in SSMS has a rather gaping limitation in that it cannot deploy dacpacs containing SqlCmd variables. I think it is worth calling out this limitation separately in this blog post because its a limitation that all dacpac users need to be aware of. If you try and deploy the dacpac containing sp_ssiscatalog using the wizard in SSMS then this is what you will see: TITLE: Microsoft SQL Server Management Studio ------------------------------ Could not deploy package. (Microsoft.SqlServer.Dac) ------------------------------ ADDITIONAL INFORMATION: Missing values for the following SqlCmd variables:SSISDB. (Microsoft.Data.Tools.Schema.Sql) ------------------------------ BUTTONS: OK ------------------------------ The message is quite correct. The SSDT DB project that I used to build this dacpac *does* have a SqlCmd variable in it called SSISDB: Quite simply, the Dac Deployment wizard in SSMS is not capable of deploying such dacpacs. Your only option for deploying such dacpacs is to use the command-line tool sqlpackage.exe. Generally I use sqlpackage.exe anyway (which is why it has taken me months to encounter the aforementioned problem) and have found it preferable to using a GUI-based wizard. Your mileage may vary. @Jamiet

    Read the article

  • Introducing the BizTalk Maturity Assessment

    - by Michael Stephenson
    Originally posted on: http://geekswithblogs.net/michaelstephenson/archive/2013/06/22/153208.aspxIn the past I have had a number of customer engagements where Ive been called in because there are problems. There were often common themes to these issues faced by customers and I had a few processes, tools and ideas about how I helped these customers.Over time I learned developed a way of analysing the customers position and this has evolved into the BizTalk Maturity Assessment which I wanted to share.  The idea is that you complete a survey which asks various things related to BizTalk in your organisation.  You are then presented with a visualization of where you sit in terms of maturity in different areas of your BizTalk capability.You should be able to see the areas you need to improve and by retaking the survey at regular intervals you should be able to demonstrate improvement.I have taken the original idea and then been joined by some of my good friends in the community and included ideas from their experience and I think we have something which will help a lot of customers and something which could be a key community asset in the future.The site for this project is on the following link:http://www.biztalkmaturity.com/There is also a case study where I have used the original assessment which demonstrated how I originally used this to help one customer get from a place where they had lots of problems to a place where they were doing BizTalk really well.

    Read the article

  • AutoCAD 11 and network file shares

    - by gravyface
    Small network of perhaps half a dozen engineers, currently working on local copies of AutoCAD project files, which are then copied back up to file server (2008 Standard, 1-2 year old Dell server hardware, RAID 5 SAS disks (10k? not positive)) at end of day. To me, this sounds horribly inefficient and error-prone, however, I've been told that "AutoCAD and network files = bad idea" and this is gospel. The network is currently 10/100 (perhaps this is the reason for the "gospel") but all the workstations are within 2 years old and have GbE NICs so an upgrade of the core switch is long overdue. However, I know certain applications don't like network access, at all, and any sign of latency or disruption brings the whole thing crashing down. Anyone care to chime in?

    Read the article

  • Using Python on Mac

    - by choise
    hi, i want to learn python using my mac. now i want to setup a python version = 3.1.3, because my materials for learning are using this version. typing python into terminal results version 2.6.1, using the dmg installer on python.org (http://docs.python.org/ftp/python/3.1.3/) doesn't have an effect on the python version in terminal, but it's bundled with an own shell under Applications/Python 3.1/Idle.app my question now is, should i use this shell for learing or is there a better way, updating the python version bundled with snow leopard? i already tried defaults write com.apple.versioner.python Version 3.1.3 or defaults write com.apple.versioner.python Version 3.0 without any result. thanks!

    Read the article

  • SQL SERVER – Four Tutorial for SQL Server 2012 New Features

    - by pinaldave
    One of the very common question I receive on my facebook is that if there is any tutorial for SQL Server 2012 new enhanced features and solutions. I see this demand a bit increasing as the SQL Server 2012 is more and more being adopted. Here is the list of four tutorial which is specifically created for SQL Server 2012 by Microsoft. Multidimensional Modeling (Adventure Works Tutorial) This tutorial teaches you how to develop and deploy an Analysis Services project that enables the employees of Adventure Works Cycles to analyze various aspects of their business. Tabular Modeling (Adventure Works Tutorial) This tutorial teaches you how to create a SQL Server 2012 Analysis Services tabular model that enable sales and marketing teams to easily analyze internet sales data in the AdventureWorksDW2012 data warehouse. You will build the tabular model in SQL Server Data Tools. Tutorials and Demos for Power View Create Power View reports and explore Power View features. View demos, videos, and tutorials that help you get started quickly with Power View and successfully build reports with interactive filters and visualizations such as bubble charts, tiles, and cards. Tutorial: Using the hierarchyid Data Type This tutorial is intended for users who are experienced with Transact-SQL, but are new to the hierarchyid data type. In this tutorial, you convert an existing table to a hierarchical structure, and you also create a new table to store and manage hierarchical data efficiently. Note: The description of the course is taken from original course description. You will need to install SQL Server 2012 AdventureWorks for all this tutorial. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Training, T SQL, Technology

    Read the article

  • Making Windows Explorer to Search WebDAV Server using DASL

    - by user124209
    I am trying to setup search in a WebDAV repository in IIS 6 on Windows Server 2003 R2. I successfully configured WebDAV in IIS and enabled my repository indexing as described in Searching WebDAV Directories (IIS 6.0) I have verified that search is now supported by my WebDAV server, in OPTIONS request I can see DASL support: DASL: <DAV:sql> DAV: 1, 2 Public: OPTIONS, TRACE, GET, HEAD, DELETE, PUT, POST, COPY, MOVE, MKCOL, PROPFIND, PROPPATCH, LOCK, UNLOCK, SEARCH Allow: OPTIONS, TRACE, GET, HEAD, DELETE, COPY, MOVE, PROPFIND, PROPPATCH, SEARCH, MKCOL, LOCK, UNLOCK I connected to my WebDAV server from a client computer, which is Windows 8.1 and WebDAV is working well. I mounted a drive and connected using \\server@port\DawWWWRoot as described here. However my client computer, which is Windows 7, does not generate any search request. I have captured requests using Fiddler tool and found that Windows Explorer is not sending any search requests, instead it is sending a PROPFIND and downloading files. How do I make Windows Explorer to send SEARCH request to my WebDAV server?

    Read the article

  • Setting up Dynamic DNS for Wireless Cameras And Accessing them Remotely

    - by Mike Szp.
    I've been trying to set up two TP LINK wireless N cameras that I bought so that I can see them remotely. I've set it up so that each has it's own ip address (192...105/192...106) and I can access them if I type that into the browser of a local computer The thing is that I don't know how to access them from another remote PC. My current setup is a a each camera connected to the router which then connects to the modem. When I set up the Dynamic DNS, and I access the "webpage" for my IP through a remote computer, it just goes to the configuration page of the modem. I have no idea how to make it go to the router or to the cameras. the router has its own ip range of 192.168.1.x while the modem has 192.168.2.x To access the cameras I type into the web browser: 192.168.1.114:100 on the local computer but I have no idea how to get there through the webpage of my Dynamic DNS remotely.

    Read the article

  • How do you KISS ?

    - by Conor
    The KISS principal is a highly quoted design mantra. The aim of this principle is to stamp out unnecessary complexity on a project. This is a good thing, saving time, energy and money. It can lead to a relatively stress free implementation and a simple, elegant, maintainable end product. A lot of discussion on KISS provides mechanisms to simplify requirements, design and implementation. Things that spring to mind include: avoid scope creep; simple obvious design and code; minimal run-time dependencies; refactoring to maintain simplicity; etc. However there are a lot of implicit things that we do to KISS. Examples: small team sizes; minimal management layers; tidy desk; mastery of a single IDE; clear concise error messages; scripts to automate/encapsulate tasks; etc The purpose of this question is to derive a checklist of KISS items. I'm especially interested in non-obvious items.

    Read the article

< Previous Page | 929 930 931 932 933 934 935 936 937 938 939 940  | Next Page >