Search Results

Search found 27042 results on 1082 pages for 'google forms'.

Page 968/1082 | < Previous Page | 964 965 966 967 968 969 970 971 972 973 974 975  | Next Page >

• PC can't detect second RAM installed

  - by kulwinder

  I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

  Read the article

• Tool to Save a Range of Disk Clusters to a File

  - by Synetech inc.

  Hi, Yesterday I deleted a (fragmented) archive file only to find that it did not extract correctly, so I was left stranded. Fortunately there was not much space free on the drive, so most of the space marked as free was from the now-deleted archive. I pulled up a disk editor and—painfully—managed to get a list of cluster ranges from the FAT that were marked as unused. My task then was to save these ranges of clusters to files so that I could examine them to try to determine which parts were from the archive and recombine them to attempt to restore the deleted file. This turned out to be a huge pain in the butt because the disk editor did not have the ability to select a range of clusters, so I had to navigate to the start of each cluster and hold down Ctrl+Shift+PgDn until I reached the end of the range (which usually took forever!) I did a quick Google search to see if I could find a command-line tool (preferably with Windows and DOS versions) that would allow me to issue a commands such as: SAVESECT -c 0xBEEF 0xCAFE FOO.BAR ::save clusters 0xBEEF-0xCAFE to FOO.BAR SAVESECT -s 1111 9876 BAZ.BIN ::save sectors 1111-9876 to BAZ.BIN Sadly my search came up empty. Any ideas? Thanks!

  Read the article

• How can I make Internet Explorer 6 render Web pages like Internet Explorer 11?

  - by gparyani

  Now, I know that this may seem like a bad question in that I can just upgrade to Internet Explorer 8, but I am sticking with IE6 in that IE8 removes valuable features, like the ability to save favorites offline and the fact that a file path turns into a Windows Explorer window and typing a Web address into Windows Explorer changes it into an IE window. I know that Internet Explorer 6 does a really bad job at rendering some pages. I know of the Google Chrome Frame extension that brings Chrome-style rendering into IE, but that will soon be discontinued. So, I tried another thing: I know that C:\Windows\System32\mshtml.dll contains the Trident rendering engine that is used by IE, so I tried something: I first backed up the original file by renaming it on Windows XP to mshtml-old.dll, then I tried to copy in the DLL from a computer running Windows 7 with Internet Explorer 10. I noticed that, after copying, the system had replaced the new DLL with the old one, but left the one I backed up intact. Is there any way I can get the system to not replace the DLL like that so that I can transfer in IE11's mshtml.dll into Windows XP and make IE6 render like IE11? I'm looking for an answer that describes how to tweak my system to make IE6 render like IE11 (or IE10), not one that tells me to upgrade IE or install another browser. I don't care how tedious the method is, just as long as it works.

  Read the article

• Pin the Dock to the top

  - by Chris Buchholz

  I wonder if it is possible to pin the Mac OS X Dock to the top in Snow Leopard? I see lets of ideas on how to do this when I google for it, and Secrets (the tweaking app) also provide it as an option, but I don't see any of the ways working for me. I guess it must have worked at some point, since people said it did, but I believe this feature might have been removed from Snow Leopard, and therefore does not work for me. Is this so? Is there really no way to pin the Dock to the top of screen? If not, what ways of "getting rid of the dock" can you guys recommend? I have tried with auto-hiding, but my problem is that this will leave a 4px line at the edge of where the Dock is pinned to, that applications wont cover. Thats not ideal for me. As far as I have understood from googling, this line will not appear if the Dock is pinned to the top, hence my question. What other ways do you guys use to get rid of it?

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• Windows and file system abstraction - how much does it matter where something comes from?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Bootcamp driver package includes file system drivers (right term?) that enable Windows to access the Mac OS HFS+ partition. AFAIK it's a read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Access Denied on Some Subfolders/Files Within a Share

  - by Tim

  First thing this morning, I find that users on one of our share drives are all getting "access denied". I tried the same drive and also received "access denied" as a Domain Admin. Previous to this, all specified users and admins could get access. I checked share permissions I checked NTFS permissions I temporarily made both types of permissions read/write to "Everyone" -- This worked for one user It turns out that this is occurring for only some files/folders. When I try to manually alter the share of that single share, it can't be shared, access denied. xcacls also gets access denied rebooted the server (not a big deal - this is a smallish company). Does anybody have any insight, my google-fu is coming up blank. Thanks. EDIT: More info, I just ran AccessEnum. There were a lot of "access denied", but I noticed the pattern that all of the access denied had a parent with an owner of "???". When I look at the properties, the "Unable to display owner" message is in the box and I can only make my user account the owner. I can then share the individual file/folder, but it doesn't seem to propogate down to subfolders/files.

  Read the article

• NRPE: Unable to read output with check_connections plugin

  - by Wlodzimierz

  I'm using plugin which gives me warning or crtis with established connections. If I run it on local machine it gives: *root@graber:/usr/lib/nagios/plugins# ./check_connections -w 1 -c 5 -C sshd CRITICAL Established connections: 6* I know, I run as root. But: Rights to the file: root@graber:/usr/lib/nagios/plugins# ls -all check_connections -rwxr-xr-x 1 nagios nagios 5459 2012-07-06 10:19 check_connections /etc/sudoers: root@graber:/usr/lib/nagios/plugins# cat /etc/sudoers Defaults env_reset root ALL=(ALL:ALL) ALL %admin ALL=(ALL) ALL nagios ALL=(ALL) NOPASSWD: /usr/bin/lsof nagios ALL=(ALL) NOPASSWD: /usr/lib/nagios/plugins/ /etc/nagios/nrpe.cfg: *nrpe_user=nagios nrpe_group=nagios* *dont_blame_nrpe=1* *command_prefix=/usr/bin/sudo command[check_connections]=/usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd* log from remote: *2012-07-06T11:12:49+02:00 graber nrpe[25928]: Handling the connection... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host address is in allowed_hosts 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host is asking for command 'check_connections' to be run... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Running command: /usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd 2012-07-06T11:19:11+02:00 graber nrpe[26100]: Return Code: 2, Output: NRPE: Unable to read output* Why is this happening? I'm out of ideas, I've searched google for 2 days now :)

  Read the article

• Updating Samba From RPMs

  - by KnickerKicker

  My Red Hat Enterprise Edition 4 comes with Samba Version 3.0.10, which does not have support for the "inherit owner" attribute that is essential in implementing a Deny-Delete Write Once Read Many share (for examples, search google for a-shared-drop-box-using-samba). (BTW, if any body knows an alternative way to do it without updating samba, I'm all ears!) I am not all that comfortable building from source, and after hours of googling (no, I do not have a red hat subscription, so I cannot just run the up2date command), I found a whole bunch of rpms on http://ftp.sernet.de/pub/samba/tested/rhel/4/i386/ (Samba 3.2.15 for RHEL 4)... Next, I tried updating them with the rpm -U --nodeps command, but I got file conflict errors. So I went ahead and overwrote everything (or so I thought) by using the rpm's --force option. But no good has come of all that. /usr/sbin/smbd -V still returns the old version. As of now, rpm -qa | grep samba returns, samba3-client-3.2.15-40.el4 samba-3.0.10-1.4E.2 samba-client-3.0.10-1.4E.2 system-config-samba-1.2.21-1 samba3-3.2.15-40.el4 samba-common-3.0.10-1.4E.2 samba3-winbind-3.2.15-40.el4 I cannot remove the older ones because samba-common >= 3.0.8-0.pre1.3 is needed by (installed) gnome-vfs2-smb-2.8.2-8.2.x86_64 libsmbclient.so.0()(64bit) is needed by (installed) kdebase-3.3.1-5.8.x86_64 libsmbclient.so.0()(64bit) is needed by (installed) gnome-vfs2-smb-2.8.2-8.2.x86_64 Now thats a whole bunch of dependencies that I dare not touch :) Any and all pointer are welcome at this stage. Thanks in advance!

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• Connecting remotely to an SQL server inside a LAN

  - by vondip

  Hello everyone, I am using SQL server 2008 inside my home lan. I've configured it to accept remote connections and I can now connect to the server from other pcs inside the lan. The problems rises when I try connecting to the server from a computer outside of my home lan. I've disabled my router's firewall and I've configured a virtual server on port 1433 forwarding to the correct lan ip. What's wrong? why is it not working? Thank you very much for your help~! Edit: This is the error I keep getting: A network related or instance specific error occured while establishing connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that the SQL SERVER is configued to allow remote connections. (provider : Sql network interfaces, error: 25- Connection string is not valid) OK these are my router's details: edimax br-6204wg I am not sure how I am supposed to browse google.com. can you be a bit more specific?

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Problem with deploying django application on mod_wsgi

  - by Shehzad009

  Hello, I seem to have a problem deploying django with mod_wsgi. In the past I've used mod_python but I want to make the change. I have been using Graham Dumpleton notes here http://code.google.com/p/modwsgi/wiki/IntegrationWithDjango1, but it still seem to not work. I get a Internal Server Error. django.wsgi file: import os import sys sys.path.append('/var/www/html') sys.path.append('/var/www/html/c2duo_crm') os.environ['DJANGO_SETTINGS_MODULE'] = 'c2duo_crm.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler() WSGIScriptAlias / /var/www/html/c2duo_crm/apache/django.wsgi Apache httpd file: <Directory /var/www/html/c2duo_crm/apache> Order allow,deny Allow from all </Directory> In my apache error log, it says I have this error This is not all of it, but I've got the most important part: [Errno 13] Permission denied: '/.python-eggs' [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] The Python egg cache directory is currently set to: [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] /.python-eggs [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] Perhaps your account does not have write access to this directory? You can [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] change the cache directory by setting the PYTHON_EGG_CACHE environment [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] variable to point to an accessible directory.

  Read the article

• Cannot browse ipv4 websites (OpenVPN )

  - by user1494428

  I have set up an openVPN tunnel on my VPS (OpenVZ - Ubuntu 12.04). The problem is when I'm connected to the vpn, I can only browse websites which support ipv6 like google. Ipv4 sites aren't loading (no error, just waiting indefinitely). http://whatismyv6.com/ reports me that I've an ipv6 address, so I guess this is the problem. Server configuration: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key dh /etc/openvpn/easy-rsa/keys/dh1024.pem push "route 10.8.0.0 255.255.255.0" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" push "redirect-gateway def1" comp-lzo persist-tun persist-key status openvpn-status.log log /var/log/openvpn.log verb 3 Client configuration: client remote xx.xx.xx.xx 1194 dev tun comp-lzo ca ca.crt cert client1.crt key client1.key redirect-gateway def1 verb 3 I have configured NAT with this command: iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -j SNAT --to xx.xx.xx.xx Can someone explain me how I can make it works (forcing ipv4?) I had the same problem with another vps and I also tried on another client (All Windows 7).

  Read the article

• why does mysql have so many more open and fragmented tables than tables in the DB?

  - by kswift

  I've been working making our database run a little smoother and had good results over the past week. But there are still some things I dont understand. For one thing, the database has 25 tables. But mysql status shows 512 are open: mysqladmin status Uptime: 212854 Threads: 1 Questions: 43041 Slow queries: 7 Opens: 2605 Flush tables: 1 Open tables: 512 Queries per second avg: 0.202 I've read that isam opens extra file descriptors and a few other reasons why the number of open tables might be higher than 25, but I am guessing that 512 is not a good thing. Any suggestions on why this might be or what I should be looking into? I've also been using mysqltuner and its been helpful. But it has consistently listed the number of fragmented tables at 207. In phpmyadmin I've selected all the tables and optimized them several times. It hasn't reduced the number of fragmented tables that mysqltuner reports. I think I am missing some important concept about how this all works. Does anyone have any suggestions to point me in the right direction or narrow down google searches or just generally help me be less clueless? Thanks!

  Read the article

• Extremely high mysqld CPU usage with no active queries

  - by RadarNyan

  I have a VPS running Ubuntu 12.04 LTS with LEMP stack, followed the guide from Linode Library (since I'm using a Linode) to setup, and everything worked fine until now. I don't know what's wrong, but my CPU usage just goes up since a week ago. Today things getting really bad - I got 74% CPU usage so I went check and found that mysqld taking too much CPU usage (somewhere around 30% ~ 80%) So I did some Google Search, tried disable InnoDB, restart mysql, reset ntp / system clock (Isn't this bug supposed to happen more than a year ago?!) and reboot my VPS, nothing helped. Even with mysql processlist empty, I still get mysqld CPU usage very high. I don't know what I missed and have totally no idea, any advice would be appreciated. Thanks in advance. Update: I got these from running "strace mysqld" write(2, "InnoDB: Unable to lock ./ibdata1"..., 44) = 44 write(2, "InnoDB: Check that you do not al"..., 115) = 115 select(0, NULL, NULL, NULL, {1, 0}^[[A^[[A) = 0 (Timeout) fcntl64(3, F_SETLK64, {type=F_WRLCK, whence=SEEK_SET, start=0, len=0}, 0xbfa496f8) = -1 EAGAIN (Resource temporarily unavailable) hum... I did tried to disable InnoDB and it didn't fix this problem. Any idea? Update2: # ps -e | grep mysqld 13099 ? 00:00:20 mysqld then use "strace -p 13099", the following lines appears repeatedly: fcntl64(12, F_GETFL) = 0x2 (flags O_RDWR) fcntl64(12, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(12, {sa_family=AF_FILE, NULL}, [2]) = 14 fcntl64(12, F_SETFL, O_RDWR) = 0 getsockname(14, {sa_family=AF_FILE, path="/var/run/mysqld/mysqld.sock"}, [30]) = 0 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0", 8) = 0 fcntl64(14, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) futex(0xb786a584, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0xb786a580, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0xb7869998, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1) = 1 ([{fd=12, revents=POLLIN}]) er... now I totally don't get it x_x help

  Read the article

• SSL timeout on some sites, across all browsers, on Mac OS X Snow Leopard

  - by dansays

  For the past several weeks, I've been receiving "Error 7 (net::ERR_TIMED_OUT): The operation timed out" when I attempt to connect to either Twitter or Paypal via SSL. I get this specific error in Google Chrome, but the same problem occurs in both Safari and Firefox. Other sites work fine, and other computers on my network can access these two sites. I have no firewall settings that would prevent me from accessing these sites over port 443. I notice that both Twitter and Paypal both have "Verisign Class 3 Extended Validation SSL CA" certificates. It is unclear whether this is related to the problem. In an effort to troubleshoot, I attempted to open the test sites referenced on Verisign's root certificate support page, which worked fine. Just to be sure, I downloaded and installed the root package file and installed all included Verisign certificates. No joy. I feel like I've hit a dead end. Any ideas? Update the first: I also cannot connect to FedEx.com, who also has a Verisign Class 3 Extended Validation cert. Update the second: Aaaaaaand it fixed itself. I did nothing. Or, I did something that worked, but in a delayed fashion. Frustrating, but a win is a win. I'll take it.

  Read the article

• Domain changes required for SSL integration

  - by user131003

  Currently my site supports regular payment options (User is taken to Payment Gateway/PG website). Now I'm trying to implement "seamless" PG integration. I need SSL for this. I'm having a dedicated server with 5 static IPs from Hostgator/HG. options: I take SSL for www.my_domain.com. According to HG, I need to change IP of main site as current IP is not really dedicated as it is being shared by cpanel etc. So They need to bind another dedicated IP to main domain for SSL to work. This would required DNS change for main website and hence cause few hours downtime (which is ok). I've noticed that most of the e-commerce websites are using subdomains like secure.my_domain.com for ssl/https. This sounds like a better approach. But I've got few doubts in this case: a) Would I need to re-register with existing PGs (Paypal, Google Checkout, Authorize.net) if I switch to subdomain? Re-registering is not an option for me. b) Would DNS change be required for www.my_domain.com in this case. This confusion arose because of following reply from HG : "If the sub domain secure.my_domain.com is added to an existing cPanel it will use the IP for that cPanel so as long as it is a Dedicated IP that will be fine. If secure.my_domain.com gets setup as its own cPanel it will need to be assigned to a Dedicated IP which would have a DNS change involved.". PLease suggest.

  Read the article

• Email flow problem in Exchange 2003

  - by Hugo Garcia

  Hello colleagues, I have a problem whit some emails that are not being delivered to the user inbox. The SMTP server on the DMZ that receives email from the internet is a Symantec Brigthmail Gateway, this server reports that the message was delivered normally to the exchange server: The DMZ server forwars the incoming mail to the exchange server that is on the LAN segment, and the message tracking on the exchange server reports the email being submited to the advanced queue: I have done severals searches on google, without any luck. have any one of you guys experienced similar problems? Any help or pointers would be very appreciated. as requested, here is a transcript of a smtp session: helo 250 mail2.XXXXXXXXXXXXXXXX.XXX.XX Hello [192.168.9.6] MAIL FROM: [email protected] RCPT TO: [email protected] DATA Subject: Mensaje de Prueba Test . 250 2.1.0 [email protected] OK 250 2.1.5 [email protected] 354 Start mail input; end with <CRLF>.<CRLF> 250 2.6.0 <'[email protected]> Queued mail for delivery

  Read the article

• Resuming downloads in Firefox

  - by Kim

  Unfortunately, Firefox still has failed to add the option to resume downloads. I've ran into this problem SO MANY times, and in my previous searches I found posts saying Firefox was going to fix that. As of 3.6.3 they haven't. I just tried Free Download Manager (FDM), again, having the Firefox addon Flashgot use it. The download gets passed to FDM, and fails, giving the error message "access denied, invalid username or password." No password was required. The site I'm trying to get the file from is turbobit.net, which limits downloads speeds to 100kb/sec, and has a 59 second countdown before you get the link. I guess it's transparently using a password on their end. If I just download normally (save to disk) the download starts fine, but it fails after 30 minutes to 1 hour (always different), and my Wi-fi connection will stop briefly - and I have to start all over. So I will never be able to download a large file. I also tried DTA instead of FMD with Flashgot, and I get an "access denied" message in DTA. Again, I reloaded - waited the 59 seconds, and download w/Firefox, and the download starts fine. The failure message in the Firefox Downloads window is "source file at http... could not be read." Any help would be greatly appreciated. When is Firefox going to finally add the ability to resume downloads????? Is there some other software I haven't found using Google that will work?

  Read the article

• Building a computer for the first time from scratch - will this really work?

  - by Nike

  Hey there. I'm building my own computer, and i just finished picking out all of my parts. Now i just want to be sure it'll all work before i order it. I'm mean specifically if the RAM & Graphic card will fit on the motherboard i chose. Below is a list of all parts. I'm sorry, i selected the parts from a Swedish website so it might be hard to understand some parts. Google Translate will help ;) I really appreciate any help/suggestions. Thanks in advance! :) Oh, and here's the parts i mentioned: EDIT: As i'm not allowed to post more than one link here, i'll just link to my homepage: http://nike1.se/c/ I know i didn't choose the most expensive parts, but this won't be my primary computer. I'm only going to use this one for testing purpose, if that makes any sense. I'm sorry for my english, i'm just so tired now. Haha! Once again, thanks in advance! :)

  Read the article

• Autologin 2 Windows users OR Login another user from the desktop

  - by fpdragon

  I'm using two windows users on my HTPC at the same time. One is just for watching videos and one for administration via remote. This setup is quite ideal for me since windows can handle multiple concurrent logins and the win "rdp concurrent hack" (Google). The problem is, I want both users to be logged in automatically when the pc was started. It shall be possible to watch tv and also the admin user shall be automatically logged in to start my scripts and other tasks, even if I haven't logged in via remote desktop manually. Later, when I want to admin my htpc I can just rdp connect the admin user without interrupting the video playback on the actual HTPC's screen and check my cleanup tasks, downloads, ... witch already executed for this admin user. But right now I found no solution to automatically login user A from a user B desktop and I also found no solution to autologin both users immediately at startup. As a workaround I have to fire up my other notebook machine and login one time with the remote user via rdp. From this time on the remote admin user is running concurrent with the main user in the background of the machine. The other workaround would be... after startup switch user from main user to admin user and then back again. But that also requires manual steps. I'm on a Windows 8 System right now but all infos for Win7 or XP would be also interesting. thanks a lot for all ideas. PS: just to prevent useless posts... don't tell me that only one user can be logged in to windows. ;)

  Read the article

• Is there any way to synchronize Outlook RSS Feeds with BlackBerry?

  - by nvuono

  Does anyone know how I can view the contents of my Outlook 2007 RSS Feeds from a corporate-issued BlackBerry? Our Inbox and Calendar are already integrated with corporate exchange servers but it looks like nobody cares too much about the RSS Feeds. Is there some setting on my Blackberry or in Outlook I could possibly tweak to include these updates? I know there are many standalone RSS readers available for blackberry (Google Reader for example) but I mention Outlook RSS Feeds specifically in my question because I am subscribing to a number of RSS feeds I've setup on my intranet for various version control systems that would be inaccessible to an external RSS reader. It seems like I might have to setup some sort of email commit notifications if I want anything from my blackberry but I much prefer the 'pull' method of an RSS feed viewer over receiving streams of emails. Please feel free to suggest any alternatives! Edit: I've additionally tried moving my "SVN Repository" folder directly into my Mailbox instead of keeping it as a child of the RSS Feeds folder. This allows me to view the SVN Repository folder on my blackberry where previously the RSS Feeds folder and all children were hidden but unfortunately it never seems to get populated with the items that are displaying in Outlook. I've even made a fresh commit to make sure that the SVN Repository folder still works correctly in Outlook from outside the RSS Feeds folder but no luck on the BlackBerry end of things. BlackBerry Model Details: BlackBerry 8310 smartphone (EDGE) v4.2.2.170 Platform 2.5.0.30

  Read the article

< Previous Page | 964 965 966 967 968 969 970 971 972 973 974 975  | Next Page >