Search Results

Search found 27232 results on 1090 pages for 'mind mapping software'.

Page 974/1090 | < Previous Page | 970 971 972 973 974 975 976 977 978 979 980 981  | Next Page >

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• Creating security permissions for a non-domain-member user in Windows Server 2008

  - by Overhed

  Hello everyone, I apologize in advance for incorrect use of terminology, as I'm not an IT person by trade. I'm doing some remote work via a VPN for a client and I need to add some DCOM Service security permissions for my remote user. Even though I'm on the VPN, the request for access to the DCOM service is using my PCs native user (and since I'm running Vista Home Premium it looks something like: PC-NAME\Username). The request for access comes back with access denied and I can not add this user to the security permissions as it "is not from a domain listed in the Select Location dialog box, and is therefore not valid". I'm pretty stuck and have no clue what kind of steps I need to do here. Any help would be appreciated, thanks in advance. EDIT: I have no control over what credentials are being passed in to the server by my computer. This scenario is occurring in an installation wizard that has a section which requests you point it to the machine running the "server" version of the software I'm installing (it then tries to invoke the relevant COM service, but my user does not have "Remove Activation Permissions" on that service, so I get request denied).

  Read the article

• Wireless card overheating?

  - by Sidney

  Ok, so I've had my laptop for several years (I wanna say 4, but possibly more), it's a Toshiba Satellite. I'm running Linux mint 15, and am having a strange new issue, after several hours of running my wireless stops. It can SEE wireless networks, but refuses to connect to any of them. (On a sidenote, connecting to a router with a cable at this point works fine) The fact that it can SEE the networks make me think the card is in good condition, and it's software related The fact that it works for several hours before booting me makes me think perhaps the transmitter is getting too hot. I don't use my laptop in dusty environments, and keep it on an elevated surface (alternatively, I actively try not to let it sit on soft surfaces where the vents get covered). I spray out the cpu fan about once a year with compressed air about once a year, so I really don't think the insides should be too dirty. Finally, unfortunately, sensors only gives me CPU temps, but they run about 40-50 degrees C, which from my understanding is perfectly normal for an I3. Does anyone have any suggestions on what I can do to determine the root cause of this?

  Read the article

• Converting PDF eBooks into a Kindle format

  - by Ender

  Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this? EDIT: I've tried Calibre, and have checked their forums to play with some of the advanced settings, yet the solutions available seem to be extremely poor, especially if the book you're attempting to read contains equations, code, or anything outside of plain text. I've also tried Amazon's conversion service, which wasn't much help with such documents. The best way I have found so far is to build the entire thing over again in ePub or RTF format and convert to MOBI from there. This works for text-heavy books with tables, but anything technical still isn't covered. Can anyone help with this?

  Read the article

• Setup: Eclipse in Ubuntu with Apache2 and Subversion

  - by Ricalsin

  Trying to setup Eclispe. I am running ubuntu 10.10 (Maverick). Apache2.2.16 Subversion 1.6.12 The Eclipse help/about/installed software says: Eclipse Platform 3.5.2 Subclipse 1.0.0 Version Control with Subversion 1.1.1 The Subclips wiki I followed is here I have installed the libsvn-java app as discussed. I added the line "-Djava.library.path=/usr/lib/jni" to the eclipse.ini file I checked the Eclipse help/about/confirguration settings and both of these lines are listed: eclipse.vmargs=-Djava.library.path=/usr/lib/jni java.library.path=/usr/lib/jni I checked that those files are in those directories. Still, when I check the preferencesteamsvn an error dialog shows: Failed to load JavaHL Library. These are the errors that were encountered: no libsvnjavahl.1 in java.library.path Incompatible JavaHL library loaded 1.3.x or later required I followed the "Testing JavaHL libraries" troubleshooting section at the bottom of the wiki: I downloaded the tarbal and ran it in a folder on my desktop with no problems. Then, I followed the instructions and placed that file INSIDE the path (usr/lib/jni/testJavaHL) and ran it from there. There are 50 tests performed and each one of them came back with this same error (posting only one for brevity): 50) testCommitRevprops(org.tigris.subversion.javahl.BasicTests)java.io.FileNotFoundException: /usr/lib/jni/testJavaHL/local_tmp/greek_files/iota (No such file or directory) at java.io.FileOutputStream.open(Native Method) at java.io.FileOutputStream.<init>(FileOutputStream.java:209) at java.io.FileOutputStream.<init>(FileOutputStream.java:160) at org.tigris.subversion.javahl.WC.materialize(WC.java:70) at org.tigris.subversion.javahl.SVNTests.buildGreekFiles(SVNTests.java:303) at org.tigris.subversion.javahl.SVNTests.setUp(SVNTests.java:222) at org.tigris.subversion.javahl.RunTests.main(RunTests.java:111) FAILURES!!! Tests run: 50, Failures: 0, Errors: 50 Any ideas as to how/why the "local_tmp/greek_files/iota" is appended to the directory? I assume that's my problem.. I'm also having a problem with newrepository location = ...as the directory location of my svn repository is one level above the home directory - which is prepended to whatever I place in the dialog box - resulting in this error: svn: '/home/ricalsin/file:/home/svn' does not exist Thank you for any help.

  Read the article

• What are the "least legally restrictive" well-connected countries to host a website?

  - by monster

  NB: I am aware that this question is subjective, as it can't be defined precisely, but the answers should still be "objective": Country name, and what makes it legally safer. EDIT: A) I am located in Germany. B) I am NOT looking for a place to offer pirated Software/Media; no binary on my site, except "profile icon". Hello! I want to start publishing "social" websites / apps, and I found that the biggest initial problem is this: Any and all services I have to depend on, including Domain Registrar, DNS provider, Server/Cloud Provider, CDN Provider, ... even my Insurance Agent, basically say that they can "throw me out" if my website contains "unacceptable" content. It's always phrased in such a way that basically anything can fall under "unacceptable" content. This is very frustrating because you just can't fully control what users post on your "social website", and you so you basically have to expect when you go to bed that your site is going to be gone when you wake up. I've heard a lot of horror stories about this. Since the "Terms Of Service" of all those providers are foremost to protect themselves from legal actions, and those legal actions depend on the country where they are located, it seems like the first step is to find which country is the "safest" to locate a site. "Safest" being defined as, where I am least likely to get in legal trouble with the local authorities, if some user posts something unacceptable in some way. The main restriction is that it should also be a "well-connected" country, because there is no point in being "safe", if my users can't get to my sites, or the latency is unacceptable. I am targeting the English speaking people in any country as my future users.

  Read the article

• What is causing ocassional white windows on my Mac?

  - by user63333

  Hello. I'm having a very strange problem with my Mac lately. When I'm working in an app and a new window pane or sheet is displayed, sometimes it comes up completely white. Once an app is having these problems, it will continue to bring up a blank screen for that particular window (although other windows work fine). After the app is relaunched, the window is fine again. What I'm noticing that's very strange is that although the interface turns completely white, the functions of the interface are still available. So I have to "navigate blindly" around the interface, until I can relaunch. This occurs throughout the operating system. Screenshots: This is what happened when I tried opening the File menu in Lightroom app. What happened to me on Lynda.com (in Firefox) after selecting the "Software..." dropdown. (All other dropdowns were fine. Reloading the page fixed it.) When I was decompressing a file, The Unarchiver launched and opened this white window. It still decompressed the file. This is what happened one time when I opened Finder (with TotalFinder) to my Downloads folder. This is something I've never seen before. This just started happening lately. What could be the problem? Thanks for your help. NOTE: since new users are not allowed to post images, just image blank white interface elements. And since new users also aren't allowed to post more than one link, here's the first screenshot:

  Read the article

• How can visiting a webpage infect your computer?

  - by Cybis

  My mother's computer recently became infected with some sort of rootkit. It began when she received an email from a close friend asking her to check out some sort of webpage. I never saw it, but my mother said it was just a blog of some sort, nothing interesting. A few days later, my mother signed in on the PayPal homepage. PayPal gave some sort of security notice which stated that to prevent fraud, they needed some additional personal information. Among some of the more normal information (name, address, etc.), they asked for her SSN and bank PIN! She refused to submit that information and complained to PayPal that they shouldn't ask for it. PayPal said they would never ask for such information and that it wasn't their webpage. There was no such "security notice" when she logged in from a different computer, only from hers. It wasn't a phishing attempt or redirection of some sort, IE clearly showed an SSL connection to https://www.paypal.com/ She remembered that strange email and asked her friend about it - the friend never sent it! Obviously, something on her computer was intercepting the PayPal homepage and that email was the only other strange thing to happen recently. She entrusted me to fix everything. I nuked the computer from orbit since it was the only way to be sure (i.e., reformatted her hard drive and did a clean install). That seemed to work fine. But that got me wondering... my mother didn't download and run anything. There were no weird ActiveX controls running (she's not computer illiterate and knows not to install them), and she only uses webmail (i.e., no Outlook vulnerability). When I think webpages, I think content presentation - JavaScript, HTML, and maybe some Flash. How could that possibly install and execute arbitrary software on your computer? It seems kinda weird/stupid that such vulnerabilities exist.

  Read the article

• Dell XPS 1530 DVD-RW firmware problem

  - by josecortesp

  Hello everyone. I have this XPS laptop since a year and a half ago. About 2 months ago, with the waranty expired, i tried to run the optiarc slot load DVD-RW firmware update, and said everything was okay. Then I restarted it and the problem started: Now, every single time I turn on my computer, it get stuck at the BIOS POST until the drive sounds like "ready" and then the computer starts normally. And this happen EXACTLY the same when it's getting back from sleep. I'm pretty sure is not a software issue, because I tried with Vista Home Premiun 32 bits, Ubuntu (from 8.10+)32 & 64, and with W7 64. Already tried to run the firmware installer like a million time, in case it is a failing install with no luck. Also, google it to see if someone has the same problem, and again, no. The Drive performs pretty okay once the System is on, but waiting to the drive to be ready everytime is really annoying. The Firmware I updated was this, and the drive is: K937C Assembly, Dvd+/-rw, 8, SLOT, 1530 Sony Nec Optiarc Inc. I'll apreciate any help you can give me

  Read the article

• Why are certain folders in my XP network share really, really slow?

  - by bikefixxer

  I have a workgroup set up with Windows XP. My file "server" is running XP Pro and the clients are running XP home. I've turned simple file sharing off on the server because certain clients need access to certain folders and not to others, and I want to keep it that way. Therefore, I've used the granular sharing/security settings to enable certain clients access to certain folders. I'm using the net use command in a batch file on the clients to add the share when they logon so it's always available via a mapped drive or a shortcut. On some clients "My Documents" points to the mapped drive, but all of the local and application settings stay local. Everything works well except for accessing a certain folder on the network. It contains a lot of random batch files and self-executable programs I use for diagnostics and what not, and nearly every time I open the folder the computer hangs for 15-60 seconds. This happens on every machine, including the server (but not nearly as often as the clients). I've searched high and low and cannot figure it out and it's driving me crazy. Here are all the things I've tried to no avail: Disabled firewall (XP) and anti-virus (ESET NOD32) Deleted any desktop.ini file I can find in the share Disabled "automatically search for network folders and printers" Disabled "remember each folder's view settings" Set HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer NoRecentDocsNetHood = 1 Tried with mapped drives and with UNC shortcuts Ran CHKDSK Removed Read-Only attribute from all folders (well, tried to remove, it always came back on with a half check) Added the server's static IP to the hosts file on the clients I've tried monitoring the server's performance to see if anything makes sense. Occasionally the issue coincides with a spike in pages/sec (memory) but not always. Other than that, everything else seems normal. The anti-virus would seem to be the most likely cause to me considering the batch files and what not, but it still hangs when it is completely disabled. I'm at a loss and if anyone can help me with this I'd greatly appreciate it!

  Read the article

• Is there any way to limit the turbo boost speed / intensity on i7 lap?

  - by Anonymous

  I've just got a used i7 laptop, one of these overheating pavilions from HP with quad cores. And I really want to find a compromise between the temp and performance. If I use linpack, or some other heavy benchmark, the temp easily gets to 95+, and having a TJ of 100 Degrees, for a 2630QM model, it really gets me throttling, that no cooling pad or even an industrial fan could solve. I figured later that it is due to turbo boost, and if I set my power settings to use 99% of the CPU instead of 100%, and it seems to disable the turbo boost, so the temp gets better. But then again it loses quite a bit of performance. The regular clock is 2GHz, and in turbo boost it gets to 2.6Ghz, but I just wonder if I could limit it to around 2.3Ghz, that would be a real nice thing. Also there is another question I've hard time getting answer to. It seems to me that clocks are very quickly boosting up to max even when not needed, eg, it's ok if the CPU has 0% load, the clocks get to their 800MHz, but even if it gets to about 5% it quickly jumps to a max and even popping up turbo, which seems very strange to me. So I wonder if there is any way to adjust the sensitivity of the Speed Step feature. I believe it would be more logical to demand increased clock if it hits let's say 50% load. I do understand that most of these features are probably hardwired somewhere in the CPU itself or the MB, which has no tuning options just like on many laptops. But I would appreciate if you could recommend some thing, or some software. Thanks

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• Can Octopussy use messages other than syslog style?

  - by Lee Lowder

  I am currently exploring different options for a centralized log server. We use both Linux (Ubuntu 10.04 / 12.04, LTS for both) and Windows, though for this specific issue only Linux is relevant. I like the interface that octopussy has and it's feature list, but I am hesitant due to a few things. One of the biggest concerns I have is that it seems to be syslog only. The end goal is to have a centralized place for our devs and admins to be able to search through the logs generated by Apache, Tomcat and 70+ web apps spread out among a cluster, for both our prod and test environments. While I did see that octopussy has support for plugins, I haven't been able to find any sort of plugin repo or in depth guides as to what can be done with them. Does anyone know if plugins can be used to allow octopussy to non-syslog messages? Specifically log4j type log messages that may include multi-line stack traces and such. Also, is there a user community for this software, such as a mailing list or forum? I've been unable to locate any so far. Thank you.

  Read the article

• Network structure --> Server 2k8r2 <--> Livebox <--> Router <--> Other PCs

  - by Yusuf

  I have a Livebox connection to the Internet and I have set up my network as follows: - Livebox <--> Win2k8R2 Server - Livebox <--> Netgear N150 Router - Router <--> Other PCs Therefore, in my LAN, - the Livebox has IP address 192.168.1.1, - the Router 192.168.1.12 (when accessed from the Livebox or the server), - the Router 10.0.0.1 (when accessed from the PCs connected to the Router), - the server 192.168.1.2, - the PCs 10.0.0.x I was using a previous configuration, which was as follows: - Livebox <--> Netgear N150 Router - Router <--> Win2k8R2 Server - Router <--> Other PCs Everything was simple, and I just had to forward all ports for incoming connection on the Livebox to the Router, and then forward the specific ports to the Server as needed (it must be however noted that any server I use is found on the Win2k8R2 server itself). In this previous configuration, the IP addresses were as follows: - Livebox 192.168.1.1 - Router 192.168.1.12 (when seen from Livebox) - Router 10.0.0.1 (when seen from server & PCs connected to it) - Server 10.0.0.2 - PCs 10.0.0.x So now of course, my port-forwarding does not work anymore since the server is not connected (directly) to the Router. What I would like to know is how do I configure the Livebox and Router to still have the features like before? From what I understand of networks (which is very limited, btw), I see these options: Make the router assign IPs like 192.168.1.x (but then I want the forwarding to be done from the router itself, is it possible?) The forwarding on the router to the server uses IP address 10.0.0.2. I could change it to 192.168.1.2 (Is that even possible, does it work?) Forward all ports from the Livebox itself to the server, and then manage them there (Is software-based port-forwarding as secure as hardware-based?)

  Read the article

• Weird glitches on Intel iGPU

  - by FrederikVds

  I have a weird problem that I can't manage to describe in one word, so I'm having trouble searching for a solution. My monitors sometimes go black for a tenth of a second. Other times, they show the image shifted a few centimeters to the left or to the right. This happens on both of my monitors, but not necessarily at the same time. I would say it happens about once a minute, unless under heavy load, in which case it can happen every second or so. Interestingly, heavy CPU/memory usage can also cause this, not just heavy GPU usage. This only happens when they are both at 1920x1080, not when one of them, or both, are at a lower resolution. It also happens when they are in mirrored mode instead of extended desktop mode. My GPU is obviously not at full clock speed most of the time: this happens at 350 MHz as well as at 1200 MHz. So it doesn't seem like a matter of too little performance. I'm not seeing any traditional artefacts, even when I use MSI Kombustor, only this kind of full-screen glitches. CPU stressing software isn't reporting any issues either. I'm thinking maybe the connection between my CPU and my PCH isn't fast enough, but I can't find anyone with the same problem to confirm that. I'd rather not invest in a discrete GPU without being certain it will fix something. Does anyone know how to search for this, or even better, does anyone have a solution? My full specs are below. Thanks in advance! Specs: ASUS P8Z77-M Intel Core i5-3570K (with Intel HD 4000 Graphics) 2x4 GB AMD Performance Edition memory Corsair Force 3 Series Rev. B 120GB SSD Maxtor 200GB HD Lite-On DVD-RW Antec 350 Watt PSU 64-bit Windows 7 Professional 2x Iiyama ProLite E2208HDS display

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• Screen Casting using ffmpeg (too fast)

  - by rowman

  I can use ffmpeg to make screen casts: ffmpeg -f x11grab -s 1280x800 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv However the output comes out to be too fast paced. It also happens with GTK RecordMyDesktop if I enable the encode on the fly. So, the questions is how to get a normal video pace. Also in order to capture the sound with ffmpeg what option should be used? FFmpeg Output: ffmpeg -f x11grab -s 1280x800 -r 30 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv ffmpeg version N-35162-g87244c8 Copyright (c) 2000-2012 the FFmpeg developers built on Oct 7 2012 15:56:19 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 51. 73.102 / 51. 73.102 libavcodec 54. 64.100 / 54. 64.100 libavformat 54. 29.105 / 54. 29.105 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 19.102 / 3. 19.102 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 16.100 / 0. 16.100 libpostproc 52. 1.100 / 52. 1.100 [x11grab @ 0xab896a0] device: :0.0 -> display: :0.0 x: 0 y: 0 width: 1280 height: 800 [x11grab @ 0xab896a0] shared memory extension found [x11grab @ 0xab896a0] Estimating duration from bitrate, this may be inaccurate Input #0, x11grab, from ':0.0': Duration: N/A, start: 1350136942.608988, bitrate: 983040 kb/s Stream #0:0: Video: rawvideo (BGR[0] / 0x524742), bgr0, 1280x800, 983040 kb/s, 30 tbr, 1000k tbn, 30 tbc [libx264 @ 0xab87320] using cpu capabilities: MMX2 SSE2Fast SSSE3 Cache64 SlowCTZ SlowAtom [libx264 @ 0xab87320] profile High 4:4:4 Predictive, level 3.2, 4:4:4 8-bit [libx264 @ 0xab87320] 264 - core 128 r2 198a7ea - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=4 threads=6 lookahead_threads=1 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=18.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, matroska, to 'out.mkv': Metadata: encoder : Lavf54.29.105 Stream #0:0: Video: h264, yuv444p, 1280x800, q=-1--1, 1k tbn, 30 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> libx264) Press [q] to stop, [?] for help frame= 10 fps=0.0 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 19 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 28 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 37 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 45 fps= 16 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 47 fps= 14 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 52 fps= 13 q=24.0 size= 257kB time=00:00:00.00 bitrate=2101632.0kbiframe= 55 fps= 12 q=24.0 size= 257kB time=00:00:00.10 bitrate=20808.2kbitsframe= 59 fps= 11 q=24.0 size= 289kB time=00:00:00.23 bitrate=10145.0kbitsframe= 64 fps= 11 q=24.0 size= 289kB time=00:00:00.40 bitrate=5894.7kbits/frame= 70 fps= 11 q=24.0 size= 289kB time=00:00:00.60 bitrate=3933.1kbits/frame= 72 fps= 10 q=24.0 size= 289kB time=00:00:00.66 bitrate=3549.2kbits/frame= 77 fps=9.8 q=24.0 size= 289kB time=00:00:00.83 bitrate=2837.7kbits/frame= 80 fps=9.6 q=24.0 size= 289kB time=00:00:00.93 bitrate=2533.5kbits/frame= 85 fps=9.3 q=24.0 size= 289kB time=00:00:01.10 bitrate=2146.9kbits/frame= 89 fps=9.3 q=24.0 size= 289kB time=00:00:01.23 bitrate=1917.1kbits/frame= 92 fps=9.1 q=24.0 size= 289kB time=00:00:01.33 bitrate=1773.3kbits/frame= 96 fps=9.0 q=24.0 size= 289kB time=00:00:01.46 bitrate=1612.4kbits/frame= 99 fps=8.8 q=24.0 size= 321kB time=00:00:01.56 bitrate=1676.8kbits/frame= 104 fps=8.7 q=24.0 size= 321kB time=00:00:01.73 bitrate=1515.2kbits/frame= 109 fps=5.3 q=24.0 Lsize= 1093kB time=00:00:03.56 bitrate=2511.5kbits/s video:1092kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.120198% [libx264 @ 0xab87320] frame I:3 Avg QP:18.93 size:142610 [libx264 @ 0xab87320] frame P:43 Avg QP:20.79 size: 15751 [libx264 @ 0xab87320] frame B:63 Avg QP:23.75 size: 195 [libx264 @ 0xab87320] consecutive B-frames: 21.1% 1.8% 11.0% 66.1% [libx264 @ 0xab87320] mb I I16..4: 50.0% 21.1% 28.9% [libx264 @ 0xab87320] mb P I16..4: 6.1% 0.9% 3.2% P16..4: 5.5% 1.2% 0.6% 0.0% 0.0% skip:82.5% [libx264 @ 0xab87320] mb B I16..4: 0.4% 0.1% 0.0% B16..8: 2.9% 0.1% 0.0% direct: 0.0% skip:96.5% L0:40.7% L1:57.0% BI: 2.3% [libx264 @ 0xab87320] 8x8 transform intra:14.5% inter:46.1% [libx264 @ 0xab87320] coded y,u,v intra: 33.5% 24.1% 25.4% inter: 0.9% 0.4% 0.4% [libx264 @ 0xab87320] i16 v,h,dc,p: 70% 26% 1% 3% [libx264 @ 0xab87320] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 11% 21% 30% 5% 7% 5% 7% 4% 10% [libx264 @ 0xab87320] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 32% 35% 12% 2% 4% 3% 4% 3% 5% [libx264 @ 0xab87320] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0xab87320] ref P L0: 57.0% 5.6% 26.8% 10.6% [libx264 @ 0xab87320] ref B L0: 69.4% 22.6% 8.0% [libx264 @ 0xab87320] ref B L1: 93.7% 6.3% [libx264 @ 0xab87320] kb/s:2460.40

  Read the article

• ubuntu 9.10 installer doesn't recognize the hard drive

  - by dan

  I downloaded Ubuntu 9.10 x86_64 and am trying to install it on a fairly modern system with a Gigabyte GA-MA770-UD3 motherboard. Ubuntu 9.04 installed fine and still will when I stick that disc in, but 9.10 doesn't see my hard drive (western digital 250GB). If I boot from the disc, I can install gparted and it does recognize the drive, but when I try to start the install process from the live disc, Ubuntu again doesn't recognize the hard drive. I checked /var/log/messages and see this: Nov 12 17:28:08 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was bad, boot with 'nodmraid'. Nov 12 17:28:08 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: no raid sets and with names: "nvidia_ciiajheb-0" Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. I checked my BIOS, SATA is enabled and is set to IDE mode, so there shouldn't be software RAID, but nonetheless, I added nodmraid to the boot line and tried again. It still doesn't recognize the drive. I checked /var/log/messages again and now see this: Nov 12 17:49:38 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was boad, boot with 'nodmraid'. Nov 12 17:49:38 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Any ideas on things to try? I've tried all of the various BIOS settings for SATA. IDE,RAID, etc. Nothing seems to work.

  Read the article

• Can SSH into remote server but can't SCP?

  - by ArtfulDodger2012

  I can SSH into remote server just fine using private key authentication with prompt for passphrase. However I'm getting permission denied when I try to SCP a file using the same passphrase. Here's my output: $ scp -v [file] [user]@[remoteserver.com]:/home/[my dir] Executing: program /usr/bin/ssh host [remoteserver.com], user [user], command scp -v -t /home/[my dir] OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /home/[my dir].ssh/config debug1: Applying options for [remoteserver.com] debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to [remoteserver.com] [[remoteserver.com]] port 22. debug1: Connection established. debug1: identity file /home/[user]/.ssh/aws_corp type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debian-3ubuntu7 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu7 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3p1 Debian-3ubuntu7 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '[remoteserver.com]' is known and matches the RSA host key. debug1: Found key in /home/[my dir]/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/[my dir]/.ssh/aws_corp debug1: PEM_read_PrivateKey failed debug1: read PEM private key done: type <unknown> Enter passphrase for key '/home/[my dir]/.ssh/aws_corp': debug1: read PEM private key done: type RSA Connection closed by [remote server] lost connection I've searched for answers but can't find quite the same problem or am just being thick. Either way any help is much appreciated. Cheers!

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• Configuring a MySQL 5.1 Instance on Windows 7 Professional x64 Fails

  - by Thomas Owens

  I'm trying to set up my laptops to function as mobile development environments. Installing the software on my Linux machine and getting it configured was fairly straightforward, however I'm having trouble getting MySQL 5.1 Server installed and configured on Windows 7 Professional 64-bit. I'm currently using the Windows MSI Installer for the complete MySQL 5.1 system (as opposed to the Essentials installer also available). I've tried to install using both the 32-bit and 64-bit versions of MySQL 5.1 - the same events occur in both. I've installed both the Server Instance Configuration Wizard and Workbench and everything appears to be installed just fine. When I open the Instance Configuration Wizard, I select Detailed Configuration. On the next screen, I select Development Environment, then Multifunctional Database on the next screen. I leave the InnoDB settings unchanged. I select Manual Setting with 5 concurrent connections. I enable TCP/IP Networking on Port 3306 and Enable Strict Mode. I select the Standard Character Set. I check the boxes for Install as a Windows Service (and provide the name "MySQL") and Include the Bin Directory in Windows PATH. On the next screen, I set my root user name and password. I do not enable root access from remote machines and I also do not create an anonymous account. On the final screen of the wizard, when I click "Execute", the first two tasks (Prepare Configuration and Write Configuration File) complete. However, when it reaches Start Service, the wizard hangs and becomes unresponsive ("Not Responding" appears in the title bar and Task Manager). I would really like to be able to use both my Windows and Linux laptops as full-blown mobile development environments, but I can't do that without being able to run MySQL. Has anyone encountered this problem before? What options do I have to correct it?

  Read the article

• XenServer 5.5 running WHS.. trying to add local or network printer/scanner/copier

  - by ProstheticHead

  Hi guys. Just wondering if anyone has prior experience in sharing a multifunction printer across a (mostly windows) network? My situation at the minute is complicated.. I DID have the printer attached directly to a Windows Home Server box and was able to scan to a share and print across the network from my other computers. Compatibility problems have forced me to virtualize WHS on XenServer 5.5... This is actually quite useful because I can now run other things on the same box, but the problem is that now WHS doesn't get direct hardware access so it doesn't see a USB attached PSC... Grrrr! So now I have a choice to make. I've read somewhere that I can buy an add in PCI USB controller and somehow set up a passthrough to one VM at a time. To me, this sound complicated but if it's likely to work reliably I'd prefer this method. I've read about another approach, which I'm not sure about either, but I guess sounds plausible. A Network USB server, (NOT a print server) that can somehow make a USB port accessible across a network. My worry here is that it likely needs some kind of 3rd party software to work.. so not ideal. If there are any other methods you can suggest I'd be happy to hear them... I need your help guys. I'm also in the market for a PCI express SATA controller, nothing flashy, just need up to 8 ports, JBOD and 100% compatability.. Any suggestions? Regards Kevin

  Read the article

• Google Drive terminates without error on startup

  - by Iszi

  I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

  Read the article

• PCs on domain can not resolve external IP addresses using the DC's DNS Server

  - by Ben

  I currently have a domain controller which handles all DHCP and DNS. The DHCP works just fine and the domain controller itself can use the internet with no issues. However, PCs that are part of the domain are not able to use external websites, only internal. Does anyone have any way I can solve this issue? Thank you Server: Windows Server 2008 R2 PC: Win7 Enterprise x64 Edit: (domain controller) C:\Users\bcollyer>nslookup google.com Server: localhost Address: 127.0.0.1 Non-authoritative answer: Name: google.com Addresses: 2a00:1450:4009:809::100e 173.194.41.166 173.194.41.165 173.194.41.169 173.194.41.162 173.194.41.161 173.194.41.160 173.194.41.168 173.194.41.167 173.194.41.164 173.194.41.163 173.194.41.174 Edit 2: C:\Users\bcollyernetstat -rn Interface List 12...30 85 a9 f7 8a 21 ......Atheros AR8161/8165 PCI-E Gigabit Ethernet Control ler (NDIS 6.20) 1...........................Software Loopback Interface 1 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11...00 00 00 00 00 00 00 e0 Microsoft Teredo Tunneling Adapter IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.0.67 172.16.0.202 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.0.0 255.255.0.0 On-link 172.16.0.202 276 172.16.0.202 255.255.255.255 On-link 172.16.0.202 276 172.16.255.255 255.255.255.255 On-link 172.16.0.202 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.0.202 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.0.202 276 Persistent Routes: None IPv6 Route Table Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link Persistent Routes: None BTW I have no javascript on the server so can't reply to individual answers... Sorry!

  Read the article

• Advice on Computer Specs for overall development/general use machine

  - by Ender

  At the moment I am restricted to a laptop with 512MB of RAM, a 120GB HDD and a 1.5GHz Intel processor for all my development and general browsing needs, and as you can probably tell using it for anything modern is a painful experience. As a result I've decided to buy myself a new desktop computer, one that will stand the test of time and one that can be upgraded easily. Rather than build the machine myself I've decided to go through Dell as I've had good experiences with them when purchasing computers for my family. I've had my eye on this as it's got a good amount of RAM, has a decent-rated processor and isn't priced too badly. http://www1.euro.dell.com/uk/en/home/Desktops/inspiron-580/pd.aspx?refid=inspiron-580&s=dhs&cs=ukepp1&~oid=uk~en~20211~inspiron-580_d005827~~ Intel® Core™ i5 Processor 750 (2.66GHz, 8MB) Genuine Windows® 7 Home Premium 64bit - English Display Not Included ATI Radeon™ HD 5450 1GB DDR3 graphics 6144MB Dual Channel DDR3 [3x2048] Memory 1TB (7200rpm) SATA Hard Drive DVD +/- RW Drive (read/write CD & DVD) with DVD Burn software 1 year of coverage included with your PC McAfee® Security Centre - 15 Month Protection - English After the pain of using a slow laptop for all this time the main thing I want is speed. I may look to play a couple of basic games on it, nothing too powerful. Obviously I'll be doing some development on it too so it'll have to be able to handle the latest IDE's and Database tools like SQL Server pretty quickly. Finally, should I ever need to improve it I'd like to be able to add more RAM and change some of the parts. I wouldn't have thought this would be a problem but a few people I've spoken to have said that the amount of RAM the motherboard can handle isn't that great. Is this true? How long can I expect to be using this computer before it's too slow? Thanks in advance for the help.

  Read the article

< Previous Page | 970 971 972 973 974 975 976 977 978 979 980 981  | Next Page >