Search Results

Search found 26810 results on 1073 pages for 'fixed point'.

Page 975/1073 | < Previous Page | 971 972 973 974 975 976 977 978 979 980 981 982  | Next Page >

• What the best way to recover from when your RAID H/W incorrectly thinks a disk is missing

  - by Software Monkey

  I have a Windows 7 system with an MSI motherboard (running the latest AMD BIOS) and two of my four disks (not the system boot disk) configured via the Mobo as RAID-1. After a normal system restart today, the RAID BIOS reports that one of the two drives has been disconnected or has failed. It's not really failed; via recovery tools I can verify that if I take the BIOS out of RAID mode. But I can find no way to re-add the second hard disk to the array and rebuild via the BIOS - the only option seems be to delete the array and recreate it, but I've done that once before and it blows away the disk. It's done this once before, however on a subsequent reboot after double-checking the drive cabling (but not changing anything) and it boot up fine. So I think the mobo RAID is a little bit flaky. At this point I would like to remove the RAID drivers, change to AHCI mode and switch over to using a Windows 7 dynamic mirror disk. But the RAID drivers seem somehow deeply bound into the Windows startup - I can't find anything like the good ol' safe-mode in Windows 7. If I boot from the Win 7 install disk in ACHI mode I can use recovery tools to log in to the Windows 7 installation, so the boot drive it seems fine with ACHI mode. Additionally, I can see all my other disks, run chkdsk on them and they seem to be fine. If I try to boot from the HDD in AHCI mode, it just reboots part way through, presumably because the RAID drivers load and conflict with the BIOS being set to AHCI. So: How do I strip the RAID drivers from my Win 7 installation? If I delete the RAID logical disk, will it really delete partitioning information, or is that just a poorly worded message when it says the data on the disk will be deleted? If I disconnect the 2 disks in a RAID array, then delete the logical disk array, and then reconnect and reboot still in RAID mode, will the disks simply revert to RAID single-disks like my other 2 and then maybe I can leave windows with RAID drivers by operate the disks as singles with 2 of them in a Windows dynamic disk mirrored setup? Does Windows 7 have anything like the Windows XP Repair Install, where it will reinstall the O/S binaries from CD, but leave apps and setup alone. I am really hoping I don't have to do a complete reinstall of Windows 7 - the last one, when I upgraded from XP, took me two days to get everything set up and installed.

  Read the article

• Is Samba Server what I'm looking for, and if so, what do I need? (currently on DD-WRT Micro)

  - by Anthony

  I am really confused as to what Samba actually does and how it works. Here's what I'm hoping it does: I set up a Samba server on my LAN, and everyone will be able to see each other's shared files and swap them. But some of the documentation makes it sound like it will just allow Mac/Linux computers to see Windows computers. Other bits of the documentation make it sound more like a local server, where a Linux machine would install Samba and they would see everyone and be visible to everyone, but that won't change if anybody else can see each other. While still other things I've read make it seem more like a file-server, where everyone sees each other but file transfers are not peer-to-peer but instead need a host disk for files to act as go between. So, assuming I'm even in the right ballpark of what Samba does in terms of my goal of total cross-visibility on the network, I am left with needing to know what I'd need to set up the server and whether it can be done and is worth it... DD-WRT's article on Samba is a bit ambiguous. One second it sounds as if I can run the server on micro as long as it's set up on a usb drive, but then it also sounds like micro can't run it at all, etc. If I can run it from a usb-connected drive, I still need to know if the files are actually stored on that drive. The dd-wrt article mentions: You can run a Samba server on your main computer and run a client on your router (thus gaining writable storage for the router) or you can use Samba to share a drive connected (typically by USB) to the router among all the computers connected to your network. That one part "to share a drive...among all the computers" makes it sound like the only benefit I get from Samba is a share drive that any OS on the network can see, but they still won't see each other. But I'm very hopeful I'm misreading this. If the computers can see each other but still need the disk, how much space is generally a good idea? I'm basing this on the idea that the drive is a temporary store point. Obviously I'd have to get a drive big enough to store everything people wanted to share if the drive is a full-on file server. If I do have this all wrong, is there any software that achieves what I have in mind? Something that connects to the main router to bridge all clients?

  Read the article

• freebsd-update from 8.3-RELEASE to 9.0-RELEASE: How to deal with dozens of diffs?

  - by Stefan Lasiewski

  I am upgrading a FreeBSD 8.3-RELEASE system to FreeBSD 9.0-RELEASE using freebsd-update. This is my first time performing a major version upgrade in FreeBSD. At one point in the process, freebsd-update performs a diff on files which are different then what is expected for the 9.0-RELEASE. It compares the current version on the system with the new changes added from 9.0-RELEASE. There are dozens of files in the list. Thus, I am presented with dozens and dozens of diffs which open in a vi window and look like this: The following file could not be merged automatically: /etc/ntp.conf Press Enter to edit this file in vi and resolve the conflicts manually... ### vi window opens <<<<<<< current version driftfile /etc/ntp/drift ======= # # $FreeBSD: release/9.0.0/etc/ntp.conf 195652 2009-07-13 05:51:33Z dwmalone $ # # Default NTP servers for the FreeBSD operating system. # # Don't forget to enable ntpd in /etc/rc.conf with: # ntpd_enable="YES" # # The driftfile is by default /var/db/ntpd.drift, check # /etc/defaults/rc.conf on how to change the location. # >>>>>>> 9.0-RELEASE restrict default notrust nomodify ignore And so on. This requires that I manually edit each file and remove the strings like <<<<<<< current version >>>>>>> 9.0-RELEASE and =======. As I discovered afterwards, if I don't remove these strings, they end up in the file afterwards. There are dozens of files which differ between 8.3 and 9.0, and I have a dozen local modifications myself. It appears that freebsd-update is using a diff, sdiff or mergemaster function of some sort, but I can't tell what it is doing exactly. Processing these files is tedious. Is there a way that I can just say "Accept new version" or "keep old version" or "Your merge is correct"? There has got to be an easier way to deal with these files. I must be missing something. This isn't a huge problem for one machine, but eventually I'll be doing this dozens of times and I want to find an easier way.

  Read the article

• How is DNS used by individual processes?

  - by atroon

  When resolving FQDNs or machine names to IP addresses on my local network (mycompany.internal) I can use dig on the command line (linux/mac) or nslookup (windows) to query the configured server and get a response. But trying to enter the FQDN or even just the machine name in a ping command or in a web browser results in 'Unknown Host' or DNS errors. Here's a sample, this one from the Mac: mac:~ atroon$ dig server.mycompany.internal ; <<>> DiG 9.6.0-APPLE-P2 <<>> server.mycompany.internal ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 5219 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.mycompany.internal. IN A ;; ANSWER SECTION: server.mycompany.internal. 1200 IN A 172.16.254.36 ;; Query time: 0 msec ;; SERVER: 172.16.254.8#53(172.16.254.8) ;; WHEN: Wed Dec 16 11:39:15 2009 ;; MSG SIZE rcvd: 55 mac:~ atroon$ ping server.mycompany.internal<br> ping: cannot resolve server.mycompany.internal: Unknown host I cannot for the life of me figure this one out. The DNS server is a SBS 2003 box which handles AD, some file/print, etc for a small company network. This issue happens to me about three times a week, and when I'm connected to the local network directly, the same switch as the server even. I can make any connection I want with IP addresses, I just can't make DNS work. Additionally, at the same time I'm experiencing this, other users are fine, which makes me think it's a problem on my Mac. But what sort of problem? How can dig send a query and get a reply, and ping say 'unknown host'? I'm posting here vs. serverfault because I think this is a local problem not a server problem...but if anyone can point me at the server, I guess we'll head down the street a domain or two.

  Read the article

• Help needed setting up nginx to serve static files.

  - by Catalina

  Hi Guys, I'm trying to setup nginx to serve static files. Basically all I need is to have http://mydomain.com/site_media/ point to /var/django/myproject/site_media. I have tried so many configurations and when I test it I always get a 404 error for static files. Can anyone please tell me what I'm doing wrong or how I should be setting this up? This is my current nginx configuration file. user www-data; worker_processes 1; #error_log /usr/local/nginx/logs/error.log; #pid /usr/local/nginx/logs/nginx.pid; events { worker_connections 1024; use epoll; } http { # Enumerate all the Tornado servers here upstream frontends { server 127.0.0.1:8000; server 127.0.0.1:8001; server 127.0.0.1:8002; server 127.0.0.1:8003; } include mime.types; default_type application/octet-stream; #access_log /usr/local/nginx/logs/access.log; keepalive_timeout 65; proxy_read_timeout 200; sendfile on; tcp_nopush on; tcp_nodelay on; gzip on; gzip_min_length 1000; gzip_proxied any; gzip_types text/plain text/html text/css text/xml application/x-javascript application/xml application/atom+xml text/javascript; proxy_next_upstream error; server { listen 80; # Allow file uploads client_max_body_size 50M; location ^~ /site_media/ { root /var/django/myproject/site_media; if ($query_string) { expires max; } } location = /favicon.ico { rewrite (.*) /site_media/favicon.ico; } location = /robots.txt { rewrite (.*) /site_media/robots.txt; } location / { proxy_pass_header Server; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_pass http://frontends; } } #include /usr/local/nginx/sites-enabled/*; } Thanks, Cata

  Read the article

• Some services refusing to start on Win 7 machine. What could the root cause be?

  - by BombDefused

  When I check msconfig, there are no services that are blocked from starting up. When I look in services.msc, the problem services have a start up type of 'Automatic', but have a blank space where others will show 'Started'. Attempting to start them manually results in the following pop up error messages. I have no idea what's causing this, looks like some sort of cascade effect from another problem service. It's affecting scheduled tasks, SQL server agent and windows back up services. How can I resolve this? I don't know how to work out what the root cause is. Task Scheduler Service Start Error: "Windows could not start the Task Scheduler service on local computer. 1068: The dependecy service or group failed to start. SQL Server Service Start Error: "The SQL Server Agent service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs." UPDATE: I've just noticed some other services have a description of "Failed to Read Description. Error Code: 2" They are: NetMsmqActivator, NetPipeActivator, NetTcpActivator, NetTcpPortSharing UPDATE 2: As joeqwerty says the Event Log service does seem to be the root of the problem. This service will not start either. It fails with 'Error 31 - A device attached to the system is not functioning correctly'. I've tried detaching all devices. I've also followed the advice here, where the same problem is described, but with no luck: http://social.technet.microsoft.com/Forums/en/w7itprosecurity/thread/44479c49-55e6-4bd7-b25e-3f2a6497306e Update 3 @ Pacey - The following was a good tip, really clear instruction. However, I found that those reg keys do not exist on my system. "Your Problem might also derive from the UpperFilter or LowerFilter Settings of the CDROM Drive. These are a known cause for Errorcode 31. You can find step-by-step instructions on removing the filters on about.com" I followed the advice through to checking every component in device manager separately, but everything is reported as working correctly!? These services did all work at one point. The hardware set up hasn't changed much. Guess I'm looking at a repair install maybe???!

  Read the article

• Unable to boot from LiveCD/USB and even Super Grub Disk!

  - by Reuben L.

  Hi all, I'm in a fix. Basically this morning, I decided to format my Win7 as it was getting really slow and I did so with no problems. I also have a Linux Mint OS on dual boot. Since I was springcleaning my windows partition, I decided it was a good idea to do the same to my linux partition. I downloaded the latest version of Linux Mint (Julia) and burned the LiveCD. Now here is where the problem lies, when I restarted Windows and chose to boot from the LiveCD, it didn't work. No joke. There was just a little underscore blinking for a long time before it went back to GRUB which prompted me to select an OS to boot. However, when I went into my old Linux Mint OS and restarted the machine, the LiveCD worked... to a certain extent. It would load and look as though it was ready to install Linux Mint 10 but the moment it got to the option screen, the whole screen turned into a checkered and jumbled mess. At this point I thought it was the LiveCD or the .iso file. I had an Ubuntu LiveUSB for recovery purposes and I tried that. The exact same thing happened. Can't boot the LiveUSB if I restarted from Windows, but works when I reboot from Linux. BUT still the same checkered screen that doesnt respond. Did a bit of googling and reckoned it might be something wrong with my GRUB. Did some updating and didnt make a difference. Then I tried the Super Grub Disk and STUPIDLY uninstalled GRUB. (Note that booting to SGD had the exact same problem - can't be done if I rebooted from Windows). Now I can't access my Linux Mint 9 cos the the bootup screen (mbr) only has Windows 7 as an option. Remember me mentioning that I can't boot from any CD/USB/recovery CD when I reboot from Windows? And now that I can't access Linux, there's no way for me to do any form of recovery! I've tried using the command prompt utility at startup recovery but to no avail. Anyone can help me with this?

  Read the article

• Varnish server in front of nginx server with multiple virtualhosts

  - by Garreth 00

  I have tried to search for a solution for this, but can't find any documentation/tips on my specific setup. My setup: Backendserver: ngnix: 2 different websites (2 top domains) in virtualenv, running gunicorn/python/django Backendserver hardware(VPS) 2gb ram, 8 CPU Databaseserver: postgresql - pg_bouncer Backendserver hardware (VPS) 1gb ram, 8 CPU Varnishserver: only running varnish Varnishserver hardware (VPS) 1gb ram, 8 CPU I'm trying to set up a varnish server to handle rare spike in traffic (20 000 unique req/s) The spike happens when a tv program mention one of the sites. What do I need to do, to make the varnish server cache both sites/domains on my backendserver? My /etc/varnish/default.vcl : backend django_backend { .host = "local.backendserver.com"; .port = "8080"; } My /usr/local/nginx/site-avaible/domain1.com upstream gunicorn_domain1 { server unix:/home/<USER>/.virtualenvs/<DOMAIN1>/<APP1>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain1.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80 default_server; listen 8080; client_max_body_size 4G; server_name www.domain1.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain1; break; } } } My /usr/local/nginx/site-avaible/domain2.com upstream gunicorn_domain2 { server unix:/home/<USER>/.virtualenvs/<DOMAIN2>/<APP2>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain2.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80; listen 8080; client_max_body_size 4G; server_name www.domain2.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain2; break; } } } Right now, If I try the Ip of the varnishserver I only get served domain1.com. Would everything be correct if I change the DNS of the two domain to point to the varnishserver, or is there extra setup before it would work? Question 2: Do I need a dedicated server for varnish, or could I just install varnish on my backendserver, or would the server run out of memory quick?

  Read the article

• How to circumvent ISP Limiting "Unknown" traffic - (SSH)Proxy, VPN

  - by connery

  I am having issues with using a proxy/VPN, with my current ISP (Comenersol, Spain). From my point of view they limit traffic by protocol or by traffic they "know" and "dont know". I'll explain my findings so far below. Internet connection in Spain: ~400-420KByte/sec (speedtest.net) OpenVPN Server in Sweden(pfsense): 100/100Mbit. LZO Compression. TCP. Tun. Aes128 Squid Proxy server in Sweden (pfsense): 100/100 (same box as the vpn server). Plain, no encryption. Runs in stealth mode to hide the use of proxy. NOT running OpenVPN or Squid Proxy, this is my findings: When I download a file from my pfsense box in Sweden, I get maximum speed When I run speedtest.net and choose any european server (including Swedish), I get max speed When I download a torrent (with non default port above 10K), I get limited to ~100KByte/sec. Encryption is turned off If I download something through https, I get max speed Running either Squid Proxy or VPN, this is my findings When I download a file from my pfsense box in Sweden, I get ~100KByte/sec When I run speedtest.net and choose any european server (including Swedish and Spanish), I get ~100Kbyte/sec When I download a torrent, I get same limitation ~100KByte/sec When I download something through https, I get ~100KByte/sec I verify the speeds above with speedtest.net measure, firefox measure in addition to having bmon running in terminal in the background. This way I am certain that the speeds I get presented, are in fact correct. If I connect through a different ISP with VPN or Squid Proxy, I get better speeds (400KByte/sec ++) In short: Whenever I tunnel my traffic through Sweden, my SPanish ISP throttles the traffic. I thought tunneling it through Squid would solve the issue, since I then would no longer hide my traffic through encryption. This does not seem to be the case. Wget and fetch gives same result. I did not try 'nc', but I assume this would give the same result. Does anyone know how to circumvent this issue? I would very much like to be able to get full speed with Swedish ip, as this would make me able to stream TV at higher quality than today. 100KByte/sec just does not cut it quality wise. Thanks for reading. Looking forward for your help.

  Read the article

• PHP-FPM performing worse than mod_php

  - by lordstyx

  Recently the website I maintain has been growing a lot and I saw the point coming where I'd want to switch from apache to nginx, because I kept on reading that it performs way better. Now I've done the switch, and I have to say, nginx is keeping up just fine. However, php-fpm is forming a problem. Where the php pages used to take 0.1 second to generate with the same load they now take around 3 seconds! Furthermore the error.log from nginx is being spammed with errors like: upstream timed out (110: Connection timed out) while connecting to upstream, client: ... I also tried using unix sockets instead, but those would complain about the following: connect() to unix:/tmp/php5-fpm.sock failed (11: Resource temporarily unavailable) while connecting to upstream I've fiddled with settings here and there but nothing seems to work. Changing the amount of pm.max_children doesn't seem to help a lot either, but with it's current amount at 350 it seems to be the lesser of all evil. The server that's being used has 3 GB RAM (not all of it is free due to a MySQL server also running) along with 2 dual-core processors (4 cores in total). Am I doing something majorly wrong with the settings here, or is the server simply not capable enough? EDIT: Here is the nginx server block server { listen 80; listen [::]:80 default ipv6only=on; root /var/www; index index.php index.html index.htm; server_name localhost; location / { try_files $uri $uri/ /index.html; } location /doc/ { alias /usr/share/doc/; autoindex on; allow 127.0.0.1; deny all; } location = /50x.html { root /usr/share/nginx/www; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(/.+)$; # NOTE: You should have "cgi.fix_pathinfo = 0;" in php.ini try_files $uri = 404; # With php5-cgi alone: fastcgi_pass 127.0.0.1:9000; # With php5-fpm: #fastcgi_pass unix:/tmp/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } location ~ /\.ht { deny all; } } And the php-fpm pool: [www] user = www-data group = www-data listen = 127.0.0.1:9000 ;listen = /tmp/php5-fpm.sock listen.backlog = -1 pm = dynamic pm.max_children = 350 pm.start_servers = 200 pm.min_spare_servers = 10 pm.max_spare_servers = 350 pm.max_requests = 1536 rlimit_files = 65536 rlimit_core = unlimited chdir = /

  Read the article

• Squid on windows loadbalancing only to one server

  - by Martin L.

  After thousands of googles and trying days i cant get the load balancer/failover in squid on windows to work. Iam using squid 2.7. My webservers are 2 single NIC lighttpd and one dual nic lighttpd. server1 in this example is running squid on port 80 and lighttpd on port 8080 (just to test) Requirements: All 3 webservers running lighttpd should be balanced two option for load balancing: Best would be if server1 is busy server2 takes over, if server2 is busy server3 takes over, etc.. Round robin style evenly distributed load. Eg server1 takes first call, server2 second etc.. All requests should be treated the same way (no url rewriting or so on) Sent host headers have to be redirected to every server as http host header, speaking of "server1", "server1.company.internal" and "10.211.1.1". My approach: acl all src all acl manager proto cache_object http_port 80 accel defaultsite=server1.company.internal vhost #reverse proxy entries cache_peer 10.211.2.1 parent 8080 0 no-query originserver round-robin login=PASS name=server1_nic1 cache_peer 10.211.1.2 parent 80 0 no-query originserver round-robin login=PASS name=server2_nic1 cache_peer 10.211.2.3 parent 8080 0 no-query originserver round-robin login=PASS name=server3_nic1 cache_peer 10.211.2.4 parent 8080 0 no-query originserver round-robin login=PASS name=server3_nic2 #decl of names of squid host acl registered_name_hostdomain dstdomain server1.company.internal acl registered_name_host dstdomain server1 #ip of squid host acl registered_name_ip dstdomain 10.211.2.1 # access: redirects the correct squid hostname http_access allow registered_name_hostdomain http_access allow registered_name_host http_access allow registered_name_ip http_access deny all cache_peer_access server1_nic1 allow registered_name_hostdomain cache_peer_access server1_nic1 allow registered_name_host cache_peer_access server1_nic1 allow registered_name_ip cache_peer_access server2_nic1 allow registered_name_hostdomain cache_peer_access server2_nic1 allow registered_name_host cache_peer_access server2_nic1 allow registered_name_ip cache_peer_access server3_nic1 allow registered_name_hostdomain cache_peer_access server3_nic1 allow registered_name_host cache_peer_access server3_nic1 allow registered_name_ip cache_peer_access server3_nic2 allow registered_name_hostdomain cache_peer_access server3_nic2 allow registered_name_host cache_peer_access server3_nic2 allow registered_name_ip cache_peer_access server1_nic1 deny all cache_peer_access server2_nic1 deny all cache_peer_access server3_nic1 deny all cache_peer_access server3_nic2 deny all never_direct allow all Problems: Load balancer does not load balance other than to first server. Only if the first server is killed in any way the second will take over. I have seen the others working at some point, but definitely not as the intended load balancing described above. If the cache_peer_access is not defined sometimes the wrong hostname is sent to the backend webserver and this always depends on the defaultsite= parameter. Probably because the host header on the request to squid is not set and its replaced by defaultsite. Leaving out defaultsite didnt solve the problem. The only workaround i found for this is the current approach with cache_peer_access. Questions: Does the cache_peer_access influence the round-robin? Is there a better workaround to pass the host header to the backed webservers? Which parameters do increase the speed of load balancing or does anyone have a better approach? -Martin

  Read the article

• How to remove RAID flag on unstriped drive without losing data?

  - by Alex Folland

  I have a Gigabyte Z68X-UD4-B3 motherboard. It advertises this new thing called "XHD", which is like RAID but makes a SSD and traditional-style drive work together to enable high speed with high capacity. I don't want to use this feature, and I already have Windows 7 64 installed without using this feature. When I first installed my 2 hard drives (1 SSD and 1 traditional-style drive) in my machine and booted it up for the first time, it ran a program from the mobo that asked me if I wanted to set up XHD. Thinking it would go to some config screen, I said yes. It immediately started doing something with my drives and finished. I considered that strange, but figured it wouldn't matter when I simply install Windows onto my SSD only. I now have my BIOS and Windows running in AHCI mode with no RAID arrays and separate drives. My SSD is one of those new Corsair Force GT drives which loses power every so often, causing Windows to BSOD. I've figured everything out about this problem, including installing the latest firmware from Corsair, and the only way to fix it at this point is by installing Intel Rapid Storage Technology to control AHCI instead of Windows, since the Windows AHCI driver disables the drive's power every once in a while and can't be configured not to do so. I've tried installing Intel Rapid Storage Technology. When I reboot my machine after doing so, it BSODs just after the Windows logo. I've figured out this is because my SSD and my traditional drive are flagged as RAID, as seen in the "Intel Matrix Storage Manager" program found by switching the BIOS hard drive handling to "RAID" mode. This is due to the XHD auto-config program I mentioned earlier. Normally, the BIOS is set to AHCI, and when the drives boot in AHCI mode, they work perfectly. So, I've concluded the data is stored in AHCI mode but the drives' flags are set to RAID. I've figured out that I can accomplish my objective by using the "Intel Matrix Storage Manager" program on the mobo (with "Reset disks to non-RAID"), but doing so would cause it to completely wipe the drives I select. I want to simply toggle these flags from RAID to AHCI so Intel Rapid Storage Technology doesn't fail and cause a BSOD upon booting, but without wiping the drives.

  Read the article

• understanding my site's DNS records

  - by DaveM

  firstly apologies for using the word 'pointage' this is the word my french domain registrar uses so I may have used to wrong term. OK I would like to better understand what is going on on my 'pointage' record on my domain registrars site. for my (currently empty) web site it reports the following details... Type : Host : Destination A : www.mydomain.org : 62.210.176.146 A : mail.mydomain.org : 84.246.225.176 Mx : .mydomain.org : mail.mydomain.org I think I understand the MX record, that simply relays anything onto the mail.mydomain.org location. However why are the destination for the www and mail domains different. Even more confusing (for me) is the fact that if I ping either of www.mydomain.org or mail.mydomain.org the ping returns a different IP address. This IP address is consistent with that of my server (ie 92.39.247.92). So what exactly is going on ? I'm sure I could find the information on the web,I've read a few thing on the debianhelp site regarding DNS records, and it seems to suggest that the record should be a reverse lookup, but certains isn't the reverse of my servers IP ? but I don't what I should be looking for, so links to docs and search terms for google will be happily accepteed (even though they go against the grain of SO answers to question). thanks in advance. David. ps. I should add that everything seems to work just fine, and I've just descovered this part of the management page of my registrar. Edit: Addition of DNS records and ping results. The DNS record for the site. From what I've read there should only realy be a single 'A' record, so has something gone wrong ? should I change it (remove the extras and then just point www.facilitee.org - .facilitee.org and mail.facilitee.org - .facilitee.org here is the DNS record A www.facilitee.org ? 92.39.247.92 A .facilitee.org ? 92.39.247.92 A mail.facilitee.org ? 92.39.247.92 A webmail.facilitee.org ? 92.39.247.92 MX .facilitee.org ? mail.facilitee.org ping results... ~$ ping www.facilitee.org PING www.facilitee.org (92.39.247.92) 56(84) bytes of data. 64 bytes from vps4576-cloud.dns26.com (92.39.247.92): ~$ ping mail.facilitee.org PING mail.facilitee.org (92.39.247.92) 56(84) bytes of data. 64 bytes from vps4576-cloud.dns26.com (92.39.247.92): So the DNS and the ping correspond, but the 'pointage' doesn't. ~ how can I get a report of the pointage records other than from my registrar ?

  Read the article

• Which hardware to VM ratio for Build-Server virtualization?

  - by Martin

  Let's start with saying that I'm a total noob wrt. to server virtualization. That is, I use VMs often during development, but they're simple desktop machine things for me. Now to my problem: We have two (physical) build servers, one master, one slave running Jenkins to do daily tasks and build (Visual C++ Builds) our release packages for our software. As such these machines are critical to our company, because we do lot's releases and without a controlled environment to create them, we can't ship fixes. (And currently there's no proper backup of these machines in place, because they do not hold any data as such - it just would be a major pain to setup them again should they go bust. (But setting up backup that I'd know would work in case of HW failure would even be more pain, so we have skipped that until now.)) Therefore (and for scaling purposes) we would like to go virtual with these machines. Outsourcing to the cloud is not an option, not at all, so we'll have to use on-premises hardware and VM hosts. Each Build-Server (master or slave) is a fully configured (installs, licenses, shares in case of the master, ...) Windows Server box. I would now ideally like to just convert the (two) existing physical nodes to VM images and run them. Later add more VM slave instances as clones of the existing ones. And here begin my questions: Should I go for one VM per one hardware-box or should I go for something where a single hardware runs multiple VMs? That would mean a single point of failure hardware wise and doesn't seem like a good idea ... or?? Since we're doing C++ compilation with Visual Studio, I assume that during a build the hardware (processor cores + disk) will be fully utilized, so going with more than one build-node per hardware doesn't seem to make much sense?? Wrt. to hardware options, does it make any difference which VM software we use (VMWare, MS, Virtualbox, ... ?) (We're using Windows exclusively for our builds.) Regarding budget: We have a normal small company (20 developers) budget for this. ;-) That is, if it's going to cost a few k$ it's going to cost. If it's free - the better. I strongly prefer solutions where there's no multi-k$ maintenance costs per year.

  Read the article

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• Make mod_wsgi use python2.7.2 instead of python2.6?

  - by guron

  i am running Ubuntu 10.04.1 LTS and it came pre-packed with python2.6 but i need to replace it with python2.7.2. (The reason is simple, 2.7 has a lot of features backported from 3 ) i had installed python2.7.2 using ./configure make make altinstall the altinstall option installed it, without touching the system default version, to /usr/local/lib/python2.7 and placed the interpreter in /usr/local/bin/python2.7 Then to help mod_wsgi find python2.7 i added the following to /etc/apache2/sites-available/wsgisite WSGIPythonHome /usr/local i start apache and run a test wsgi app BUT i am greeted by python 2.6.5 and not Python2.7 Later i replaced the default python simlink to point to python 2.7 ln -f /usr/local/bin/python2.7 /usr/bin/python Now typing 'python' on the console opens python2.7 but somehow mod_wsgi still picks up python2.6 Next i tried, PATH=/usr/local/bin:$PATH export PATH then do a quick restart apache, but yet again its python2.6 !! Here is my $PATH /usr/local/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games contents of /etc/apache2/sites-available/wsgisite WSGIPythonHome /usr/local <VirtualHost *:80> ServerName wsgitest.local DocumentRoot /home/wwwhost/pydocs/wsgi <Directory /home/wwwhost/pydocs/wsgi> Order allow,deny Allow from all </Directory> WSGIScriptAlias / /home/wwwhost/pydocs/wsgi/app.wsgi </VirtualHost> app.wsgi import sys def application(environ, start_response): status = '200 OK' output = sys.version response_headers = [('Content-type', 'text/plain'), ('Content-Length', str(len(output)))] start_response(status, response_headers) return [output] Apache error.log 'import site' failed; use -v for traceback [Sun Jun 19 00:27:21 2011] [info] mod_wsgi (pid=23235): Initializing Python. [Sun Jun 19 00:27:21 2011] [notice] Apache/2.2.14 (Ubuntu) mod_wsgi/2.8 Python/2.6.5 configured -- resuming normal operations [Sun Jun 19 00:27:21 2011] [info] Server built: Nov 18 2010 21:20:56 [Sun Jun 19 00:27:21 2011] [info] mod_wsgi (pid=23238): Attach interpreter ''. [Sun Jun 19 00:27:21 2011] [info] mod_wsgi (pid=23239): Attach interpreter ''. [Sun Jun 19 00:27:31 2011] [info] mod_wsgi (pid=23238): Create interpreter 'wsgitest.local|'. [Sun Jun 19 00:27:31 2011] [info] [client 192.168.1.205] mod_wsgi (pid=23238, process='', application='wsgitest.local|'): Loading WSGI script '/home/wwwhost/pydocs/$ [Sun Jun 19 00:27:50 2011] [info] mod_wsgi (pid=23239): Create interpreter 'wsgitest.local|'. Has anybody ever managed to make mod_wsgi run on a non-system default version of python ?

  Read the article

• Trouble creating FTP in Server 2008

  - by Saariko

  I have been trying to create an FTP server on my new Server 2008. I have been following both (very detailed and highly published here guides) For setting up using IIS Manager http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/ and For anonymous FTP http://www.trainsignaltraining.com/windows-server-2008-ftp-iis7 I am able to log as an anonymous user. My need is to use a named user, so I need to use the IIS Manager. I get error 530 when trying to log as a user. Connected to 127.0.0.1. 220 Microsoft FTP Service User (127.0.0.1:(none)): ftpmanager 331 Password required for ftpmanager. Password: 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: Filename: Error: 530 End Login failed. ftp> I can not learn from this message anything. My password is set to: 1234 (so I don't think I make a mistake here - testing purposes only ofc) Thank you. Note - I went over other posts on SE that I read, and couldn't get the result: IIS7 Windows Server 2008 FTP -> Response: 530 User cannot log in. FTP Error 530, User cannot log in, home directory inaccessible. Having trouble setting up FTP server on Windows Server 2008 EDIT I think I found some errors with the physical path. Going to Basic settings, and Test Connection on the physical path, gave me the following error: The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that \$ has Read access to the physical path. Then test these settings again. I am not sure which/whom should get access to the Root folder !? I want to point out, I managed to login with a domain user (change authorization and authentication methods) but this is NOT the requested solution. I checked to make sure that the FTP, folders, access is working properly. I am bit lost here. ==== More tries: I have enabled another Allow rule for ALL Users. I still get the same error. It seems that it doesn't matter if i use a correct or wrong password, I still get Error 530.

  Read the article

• Model M Keyboard inputs incorrect characters after logging in to Fedora

  - by mickburkejnr

  I recently bought a 24 year old IBM Model M keyboard. From what I gather, it'd been left on a shelf for the last 5 years, so you can imagine the amount of dust dirt and crap that was on it. Before cleaning it, I plugged it in to my laptop (running Fedora 17) using a PS/2 to USB adapter. What I found was, while it still works, the keys I press don't correspond to what is displayed on the screen. So for example, when I type S on the keyboard, I get ß display on the screen instead. At the time, I put this down to the adapter not working properly. Since then, I stripped the keys off the keyboard and cleaned the whole thing. It looks like it's just come out of a box! I then plugged it in to my computer (also running Fedora 17) via a standard PS/2 plug. The computer loaded up to the login screen, and I typed in my password. Pressed enter, and I logged straight in to my machine. At this point, I opened up a text editor and started typing some stuff. To my horror, the keystrokes I was entering weren't coming up as intended. What came up instead were characters that would map to the pressed key but only under a different keyboard language setting. I opened up a program to see what keyboard language had been selected, and the correct one for the keyboard was selected (which is UK in my case). I opened up a window that would show what characters mapped to what keys, and I pressed every single key on the keyboard, and every corresponding block representing each key lit up. I went back to the text editor to try again, but I was still getting these random characters. Whats more is that the backspace key would not work, although in the other utility it would flash when pressed. What I know is that at the login screen the keyboard must have entered the correct characters, otherwise I wouldn't have been able to log in. Further more, keys that don't respond while using a text editor as sending signals to the computer, as illustrated in that keyboard utility. The question is why random characters are displayed when they really shouldn't be? Would this be a hardware fault or a software issue?

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• Remote access to internal machine (ssh port-forwarding)

  - by MacUsers

  I have a server (serv05) at work with a public ip, hosting two KVM guests - vtest1 & vtest2 - in two different private network - 192.168.122.0 & 192.168.100.0 - respectively, this way: [root@serv05 ~]# ip -o addr show | grep -w inet 1: lo inet 127.0.0.1/8 scope host lo 2: eth0 inet xxx.xxx.xx.197/24 brd xxx.xxx.xx.255 scope global eth0 4: virbr1 inet 192.168.100.1/24 brd 192.168.100.255 scope global virbr1 6: virbr0 inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0 # [root@serv05 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr1 xxx.xxx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 0.0.0.0 xxx.xxx.xx.62 0.0.0.0 UG 0 0 0 eth0 I've also setup IP FORWARDing and Masquerading this way: iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface virbr0 -j ACCEPT All works up to this point. If I want to remote access vtest1 (or vtest2) first I ssh to serv05 and then from there ssh to vtest1. Is there a way to setup a port forwarding so that vtest1 can be accessed directly from the outside world? This is what I probably need to setup: external_ip (tcp port 4444) -> DNAT -> 192.168.122.50 (tcp port 22) I know it's easily do'able using a SOHO router but can't figure out how can I do that on a Linux box. Any help form you guys?? Cheers!! Update: 1 Now I've made ssh to listen to both of the ports: [root@serv05 ssh]# netstat -tulpn | grep ssh tcp 0 0 xxx.xxx.xx.197:22 0.0.0.0:* LISTEN 5092/sshd tcp 0 0 xxx.xxx.xx.197:4444 0.0.0.0:* LISTEN 5092/sshd and port 4444 is allowed in the iptables rules: [root@serv05 sysconfig]# grep 4444 iptables -A PREROUTING -i eth0 -p tcp -m tcp --dport 4444 -j DNAT --to-destination 192.168.122.50:22 -A INPUT -p tcp -m state --state NEW -m tcp --dport 4444 -j ACCEPT -A FORWARD -i eth0 -p tcp -m tcp --dport 4444 -j ACCEPT But I'm getting connection refused: maci:~ santa$ telnet serv05 4444 Trying xxx.xxx.xx.197... telnet: connect to address xxx.xxx.xx.197: Connection refused telnet: Unable to connect to remote host Any idea what's I'm still missing? Cheers!!

  Read the article

• linux disk usage report inconsistancy after removing file. cpanel inaccurate disk usage report

  - by brando

  relevant software: Red Hat Enterprise Linux Server release 6.3 (Santiago) cpanel installed 11.34.0 (build 7) background and problem: I was getting a disk usage warning (via cpanel) because /var seemed to be filling up on my server. The assumption would be that there was a log file growing too large and filling up the partition. I recently removed a large log file and changed my syslog config to rotate the log files more regularly. I removed something like /var/log/somefile and edited /etc/rsyslog.conf. This is the reason I was suspicious of the disk usage report warning issued by cpanel that I was getting because it didn't seem right. This is what df was reporting for the partitions: $ [/var]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 511M 8.9G 6% / tmpfs 5.9G 0 5.9G 0% /dev/shm /dev/sda1 99M 53M 42M 56% /boot /dev/sda8 883G 384G 455G 46% /home /dev/sdb1 9.9G 151M 9.3G 2% /tmp /dev/sda3 9.9G 7.8G 1.6G 84% /usr /dev/sda5 9.9G 9.3G 108M 99% /var This is what du was reporting for /var mount point: $ [/var]# du -sh 528M . clearly something funky was going on. I had a similar kind of reporting inconsistency in the past and I restarted the server and df reporting seemed to be correct after that. I decided to reboot the server to see if the same thing would happpen. This is what df reports now: $ [~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 511M 8.9G 6% / tmpfs 5.9G 0 5.9G 0% /dev/shm /dev/sda1 99M 53M 42M 56% /boot /dev/sda8 883G 384G 455G 46% /home /dev/sdb1 9.9G 151M 9.3G 2% /tmp /dev/sda3 9.9G 7.8G 1.6G 84% /usr /dev/sda5 9.9G 697M 8.7G 8% /var This looks more like what I'd expect to get. For consistency this is what du reports for /var: $ [/var]# du -sh 638M . question: This is a nuisance. I'm not sure where the disk usage reports issued by cpanel get their info but it clearly isn't correct. How can I avoid this inaccurate reporting in the future? It seems like df reporting wrong disk usage is a strong indicator of the source problem but I'm not sure. Is there a way to 'refresh' the filesystem somehow so that the df report is accurate without restarting the server? Any other ideas for resolving this issue?

  Read the article

• Logitech Optical Mouse Frozen In Middle of Windows XP Pro Screen

  - by Code Sherpa

  Hi. I have a Logitech Optical Mouse/Keyboard. I have been using them just fine with the system drivers for almost a year now. I recently updated my Kaspersky software and rebooted. Now the mouse is frozen in the middle of my screen. I am not able to login to the Windows XP Pro box that has the frozen mouse (because i can't work the mouse) but am able to remote desktop to this computer. Things I know / have tried: When I boot on the problem computer, I am able to use the keyboard, but not the mouse. I have installed the latest version of Logitech's SetPoint (with the updated drivers) on the problem computer (via remote desktop) and that didn't seem to matter. I bought new batteries for the mouse and that didn't matter. I have tried the mouse/keyboard on another computer and the mouse works just fine there. My suspicion is that the Kaspersky install has overwritten a driver of some sort. Things I have not done (and would appreciate detailed steps if you feel this is the way to go): 1) Uninstalled all the mouse drivers on the machine and reboot. Then, reinstall. Note: When I get to the Device Manager I don't see an option for Human Interface Devices (where the mouse device is). Here are my options: Computer, Disk Drives, DVD/CD-Rom drives, Floppy controllers, IDE ATA/ATAPI, Imaging devices, Network Adapters, Other devices, Ports, Processors, Sound, video, and gaming, System devices, USB controllers. Also, I should point out that Video Controller is the only thing under Other devices and it has a yellow exclamation mark. The same is true for all the items under Universal Serial Bus controllers. I think this means I have to update my BIOS but, since my mouse was working just fine without doing that, I don't think that is my problem. So, how do I get to my Mouse Device? 2) Update my BIOS. Note: As pointed out above, I don't think this matters as my mouse was working just fine under my computer's current BIOS version. Thanks for your help.

  Read the article

• Some Memory Slots Not Working on MSI FM2-A85XA-G65 Motherboard

  - by Mike Ciaraldi

  Short version of question: Does anyone have an MSI FM2-A85XA-G65 motherboard, who can confirm that all four memory slots work? Long version: Several months ago I bought an MSI FM2-A85XA-G65 motherboard at Newegg. At that point I installed an AMD A8-5500 processor and two sticks of Corsair Vengeance 8 GB DDR3-1866 memory, and put it into my file server. I installed the RAM in slots 1 and 3, as directed in the manual, to enable dual-channel memory access. It seemed to work fine, so I bought a second identical mobo (which arrived dead, but was quickly replaced by Newegg) and set of RAM, installed an A10-5800K, and put that into my production Linux machine. Again, it seemed to work well. Eventually I happened to notice that on the server only 8 GB of RAM appeared in the BIOS. I tried each of the slots and memory modules individually and in various combinations. I even swapped processors with the production machine. The result was that putting memory in slots 1 and 2 worked (showing a total of 16 GB), but any memory in slots 3 or 4 was not recognized. However, all four memory slots in the production machine worked, and I confirmed this with both processors. I contacted MSI and arranged to ship the defective mobo back to them for replacement under warranty. I did not want my file server to be down in the interim, and I had another machine I wanted to upgrade, so I bought a third identical mobo to use. That one had the same problem -- only memory slots 1 and 2 worked. I tested it thoroughly with multiple processors and memory sticks. I sent the defective mobo back to MSI and they sent me a new one. This has the same memory slot problem. So I sent it back. The replacement arrived the other day and shows the same problem. I contacted MSI yet again and they said that nobody else has reported memory slot problems on this board and it must be my processor. So my score so far is, out of six boards of this model, I have: One where all four slots work. One which was dead on arrival. Four where only memory slots 1 and 2 work. Before I tear my other machines apart and start swapping processors again I thought I would ask if anyone else has this exact model motherboard and could confirm that all four memory slots either do or do not work. According to MSI you should be able to just plug a single memory module into any of the slots and it will work (and it does on the one mobo I have which works correctly). If you have not yet used all four slots, this is a good time to test them so you know if you can expand your memory in the future. Thanks in advance to anyone who can help.

  Read the article

• Windows 7 losing one of my displays after restart

  - by j_kubik

  I have an Intel DZ68BC motherboard with Intel HD graphics card using two monitors (on DVI and on HDMI » VGA). My friend asked me to test if his NVIDIA graphics card works well on my computer (at his it was doing some trouble), so I inserted it in my computer, installed the NVIDIA driver and it worked quite well. Then I removed it, uninstalled everything NVIDIA-related I could find and switched monitors back to my Intel card. Since then after every system start/restart, the system sees only monitor on HDMI » VGA connector, completely ignoring the DVI monitor. I noticed that installing the Intel video drivers causes the system to recognize the second monitor if I don't immediately reboot. After a reboot, the system recognizes only the HDMI » VGA monitor. I also tried starting in safe-mode and using DriveSweeper to remove the remains of NVIDIA drivers. While it seems that some drivers were removed, the situation didn't change. Now I am out of ideas and I really wouldn't like to reinstall the system (again...). I also tried restoring the system to the state before this whole story, but it also didn't change anything. EDIT: I am still trying to troubleshoot this problem. The only point that I could start was driver re-instalation. I traced down the part that restores right settings to a call: C:\Users\Jarek\Desktop\GFX_Win7_64_8.15.10.2696\x64\Drv64.exe -driverinf "C:\Users\Jarek\Desktop\GFX_Win7_64_8.15.10.2696\Graphics\igdlh64.inf" -flags 20 -keypath "Software\Intel\Difx64" This call fixes my displays, and as workaround, I will add it for now to my autorun. I am still looking for better solution anyway... EDIT2: Using DriverView i made a list of currently used drivers both before and after fixing my display using above command. Then i compared logs: No drivers were removed by fixing command. Drivers added by fixing command: MS Remote Access serial network driver (asyncmac.sys) security processor (spsys.sys) Drivers that changed base address (indicates driver-reload?) Canonical Display Driver (cdd.dll) Intel Graphics Kernel Mode Driver (igdkmd64.sys) Monitor Driver (monitor.sys) Added drivers seem rather unrelated to the problem to me, reloaded drivers are just a cnsequence of installing new driver file so there is not much to go here... I really cannot make heads or tails out of it...

  Read the article

• Is there a Distributed SAN/Storage System out there?

  - by Joel Coel

  Like many other places, we ask our users not to save files to their local machines. Instead, we encourage that they be put on a file server so that others (with appropriate permissions) can use them and that the files are backed up properly. The result of this is that most users have large hard drives that are sitting mainly empty. It's 2010 now. Surely there is a system out there that lets you turn that empty space into a virtual SAN or document library? What I envision is a client program that is pushed out to users' PCs that coordinates with a central server. The server looks to users just like a normal file server, but instead of keeping entire file contents it merely keeps a record of where those files can be found among various user PCs. It then coordinates with the right clients to serve up file requests. The client software would be able to respond to such requests directly, as well as be smart enough to cache recent files locally. For redundancy the server could make sure files are copied to multiple PCs, perhaps allowing you to define groups in different locations so that an instance of the entire repository lives in each group to protect against a disaster in one building taking down everything else. Obviously you wouldn't point your database server here, but for simpler things I see several advantages: Files can often be transferred from a nearer machine. Disk space grows automatically as your company does. Should ultimately be cheaper, as you don't need to keep a separate set of disks I can see a few downsides as well: Occasional degradation of user pc performance, if the machine has to serve or accept a large file transfer during a busy period. Writes have to be propogated around the network several times (though I suspect this isn't really much of a problem, as reading happens in most places more than writing) Still need a way to send a complete copy of the data offsite occasionally, and this would make it very hard to do differentials Think of this like a cloud storage system that lives entirely within your corporate LAN and makes use of your existing user equipment. Our old main file server is due for retirement in about 2 years, and I'm looking into replacing it with a small SAN. I'm thinking something like this would be a better fit. As a school, we have a couple computer labs I can leave running that would be perfect for adding a little extra redundancy to the system. Unfortunately, the closest thing I can find is Dienst, and it's just a paper that dates back to 1994. Am I just using the wrong buzzwords in my searches, or does this really not exist? If not, is there a big downside that I'm missing?

  Read the article

< Previous Page | 971 972 973 974 975 976 977 978 979 980 981 982  | Next Page >