Search Results

Search found 4290 results on 172 pages for 'y low'.

Page 99/172 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

• Ubuntu does not recognize my built-in monitor.

  - by B3tturTh3nU

  I've recently discovered of a boot problem Ubuntu has with my laptop. I have successfully installed Ubuntu on two other computers, and I've never experienced this problem. What happens is, after the live boot CD loads, the screen goes completely blank. Although, I suspected that there was no problem booting, so I loaded with BIOS only, which worked perfectly fine. Of course, not being very proficient with this, I have no idea what needs to be done to fix the problem. I have switchable graphics cards(the ATI Mobility Radeon HD 5650, and some low-end Intel card), and an Intel i5 quad core processor. I was booting with the Ubuntu 10.10 64 bit desktop distribution. If there's any more information you need from me, please let me know. EDIT: I was able to look into this a bit more, thanks to one of the comments provided, and I have some new information. Ubuntu does seem to be able to recognize both of my graphics cards. The problem I found was that, in the Xorg.0 log, it mentions that there were "no screens found." I'm using a notebook, so the screen is built in. Does anyone know of a way to get Ubuntu to recognize the monitor?

  Read the article

• Can't connect to Wireless Network - Ubuntu 12.04 LTS & Sabrent A111N USB Dongle

  - by Ohgodwhy

  I've been trying to connect to this network for quite some time. I can't directly connect to the router with a Wire, but can access the Router with other wireless devices without any issues. I had previously tried several other Wifi nic's but none of them would load properly. Today, i went and bought a new (supported) Sabrent A111N USB Dongle, which said explicitly that it works with Linux 2.4 +. I popped the Dongle in, and low-and-behold it immediately said that there were Available Wireless Connections. I selected my connection and tried to connect, but it just loops constantly while saying Wireless Disconnected then attempts to connect again over and over. ifconfig and iwconfig both show my device in a ready and working state. However, iwlist wlan0 scan says that there are no results found. I don't get it... At one point, I could see the CPU in the DHCP client list under the router, but it doesn't fully make the connection (something about a timeout?). Any help would be appreciated. Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN

  Read the article

• How to handle monetary values in PHP and MySql?

  - by Songo

  I've inherited a huge pile of legacy code written in PHP on top of a MySQL database. The thing I noticed is that the application uses doubles for storage and manipulation of data. Now I came across of numerous posts mentioning how double are not suited for monetary operations because of the rounding errors. However, I have yet to come across a complete solution to how monetary values should be handled in PHP code and stored in a MySQL database. Is there a best practice when it comes to handling money specifically in PHP? Things I'm looking for are: How should the data be stored in the database? column type? size? How should the data be handling in normal addition, subtraction. multiplication or division? When should I round the values? How much rounding is acceptable if any? Is there a difference between handling large monetary values and low ones? Note: A VERY simplified sample code of how I might encounter money values in everyday life: $a= $_POST['price_in_dollars']; //-->(ex: 25.06) will be read as a string should it be cast to double? $b= $_POST['discount_rate'];//-->(ex: 0.35) value will always be less than 1 $valueToBeStored= $a * $b; //--> any hint here is welcomed $valueFromDatabase= $row['price']; //--> price column in database could be double, decimal,...etc. $priceToPrint=$valueFromDatabase * 0.25; //again cast needed or not? I hope you use this sample code as a means to bring out more use cases and not to take it literally of course. Bonus Question If I'm to use an ORM such as Doctrine or PROPEL, how different will it be to use money in my code.

  Read the article

• Understanding Application binary interface (ABI)

  - by Tim

  I am trying to understand the concept of Application binary interface (ABI). From The Linux Kernel Primer: An ABI is a set of conventions that allows a linker to combine separately compiled modules into one unit without recompilation, such as calling conventions, machine interface, and operating-system interface. Among other things, an ABI defines the binary interface between these units. ... The benefits of conforming to an ABI are that it allows linking object files compiled by different compilers. From Wikipedia: an application binary interface (ABI) describes the low-level interface between an application (or any type of) program and the operating system or another application. ABIs cover details such as data type, size, and alignment; the calling convention, which controls how functions' arguments are passed and return values retrieved; the system call numbers and how an application should make system calls to the operating system; and in the case of a complete operating system ABI, the binary format of object files, program libraries and so on. I was wondering whether ABI depends on both the instruction set and the OS. Are the two all that ABI depends on? What kinds of role does ABI play in different stages of compilation: preprocessing, conversion of code from C to Assembly, conversion of code from Assembly to Machine code, and linking? From the first quote above, it seems to me that ABI is needed for only linking stage, not the other stages. Is it correct? When is ABI needed to be considered? Is ABI needed to be considered during programming in C, Assembly or other languages? If yes, how are ABI and API different? Or is it only for linker or compiler? Is ABI specified for/in machine code, Assembly language, and/or of C?

  Read the article

• Splitting a tetris game apart - where to put time-management?

  - by nightcracker

  I am creating a tetris game in C++ & SDL, and I'm trying to do it "good" by making it object-oriented and keeping scopes small. So far I have the following structure: A main with some lowlevel SDL set up and handling input A game class that keeps track of score and provides the interface for main (move block down, etc) A map class that keeps track of the current game field, which blocks are where. Used by the game class. A block class that consists of the current falling block, used by game. A renderer class abstracting low level SDL to a format where you render "tetris blocks". Used by map and block. Now I have a though time where to place the time-management of this game. For example, where should be decided when a block bumps the bottom of the screen how long it takes the current block locks in place and a new block spawns? I also have an other unrelated question, is there some place where you can find some standard data on tetris like standard score tables, rulesets, timings, etc?

  Read the article

• OpenWorld 2011 Video Index

  - by Chris Kawalek

  We did quite a few virtualization videos this year at Oracle OpenWorld 2011. You can find all these and more on our YouTube channel. Virtualization Wrapup Adam Hawley discusses the Oracle virtualization presence at Oracle OpenWorld 2011. http://www.youtube.com/oraclevirtualization#p/f/2/53_SQYljqN4 Oracle Applications on iPad Brad Lackey shows how you can access Oracle Applications on iPad. http://www.youtube.com/oraclevirtualization#p/f/9/3Ug5km3uxEQ Thinkquest.org and Oracle VM Dan Herrup describes how Thinkquest.org is using Oracle VM to help kids learn how to solve real world problems with computer technology. http://www.youtube.com/oraclevirtualization#p/f/6/Bw-km5kqzEo Avaya and Oracle Virtualization See Oracle desktop virtualization in action at Avaya's booth. http://www.youtube.com/oraclevirtualization#p/f/4/xIHRIijEPkM Eco-Features of Sun Ray Clients Michael Dann shows off the Sun Ray 3 Plus and talks about the eco benefits of Oracle's extremely low power consumption client device for desktop virtualization. http://www.youtube.com/oraclevirtualization#p/f/3/ulArHGe1OmM Application and Desktop Access with Oracle Secure Global Desktop Watch Jeff Harvey do a quick demo of Oracle Secure Global Desktop accessing Oracle Applications. http://www.youtube.com/oraclevirtualization#p/f/5/g_ikA7dwh0g Oracle VM VirtualBox for VDI Andy Hall describes how enterprises leverage Oracle VM VirtualBox as part of their VDI deployments. http://www.youtube.com/oraclevirtualization#p/f/8/WmkeYlzgnZ8 TechCast Live: The Coolest Virtualization Products Interview with Andy Hall about the desktop virtualization portfolio. http://www.youtube.com/oraclevirtualization#p/f/7/VMkrAhZ83AA

  Read the article

• My game seems to be incompatible with recording software. What could be causing this?

  - by Lewis Wakeford

  I've just finished a little Game-Dev project for university and I need to record a video to accompany my submission (just in case they can't get my source to work). Basically my game doesn't work at all when FRAPS or Bandicam attempts to attach to it, I get a black screen and a stream of GL INVALID OPERATION messages from my error reporting code. Dxtory can't seem to hook into it correctly at all, it doesn't display it's FPS counter or anything. My game logic appears to be running correctly from the debug traces, it just seems like all the gl library calls break. I don't know a huge amount about how these programs operate so I don't really know what I could be doing to cause this. I've heard they read from the OpenGL frame buffers so maybe I'm doing something wrong there? I'm letting GLFW and GLEW do all the low level initialization, but I have successfully recorded projects with the same setup and recording software. Essentially, has anyone ever run into something like this before or do you know anything about how these programs work that could give a clue as to the cause of the issue?

  Read the article

• How to uninstall Ubuntu 12.04 LTS dual booting with Windows 7?

  - by user103799

  I need to uninstall Ubuntu 12.04 LTS from my laptop. It's currently dual booting with windows 7. I've searched and found some ways to do this, but all use some kind of a CD to complete the deletion. I have neither the Ubuntu Live CD nor Windows Install CD/Recovery CD. This laptop did not come with one, and I unfortunately have no available storage device to make a recovery CD. Is there a way to completely uninstall Ubuntu 12.04 LTS dual booting without using any hardware? If there's no way, then how to uninstall using the least hardware possible? Or easy to find hardware? I've nothing against Ubuntu. I installed this as a backup/alternative to error-prone Windows 7. However, after a hardware upgrade, including extra RAMs and a new, better CPU, Windows 7 runs smoothly again. Now I'm running low on hard drive space and need the 40 gig or so of space I partitioned for Ubuntu back. Any help is appreciated, and thanks in advance!

  Read the article

• Java Components Landing Page and Documentation Updates

  - by joni g.

  The new Java Components page provides access to the documentation for tools that are available for monitoring, managing, and testing Java applications. Documentation for the new versions of the following tools is available: JavaTest Harness 4.6. The JavaTest harness is a general purpose, fully-featured, flexible, and configurable test harness that is suited for most types of unit testing. See the JavaTest tab for documentation. SigTest 3.1. SigTest is a collection of tools that can be used to compare APIs and to measure the test coverage of an API. See the SigTest tab for documentation. The following tools are part of Oracle Java SE Advanced and Oracle Java SE Suite. Java Mission Control and Java Flight Control 5.4 are supported in JDK 8u20. Java Flight Recorder and Java Mission Control together create a complete tool chain to continuously collect low level and detailed runtime information enabling after-the-fact incident analysis. See the JMC tab for documentation. Advanced Management Console 1.0 is a new tool that is now available. AMC can be used to view information about the Java applets and Java Web Start applications running in your enterprise, and create deployment rules and rule sets to manage the execution of these applications. See the AMC tab for documentation. Usage Tracker tracks how Java Runtime Environments (JREs) are being used in your systems. See the Usage Tracker tab for documentation.

  Read the article

• Ubuntu 12.04 Freezes w/ Ethernet Unplugged + Wireless Drops (Acer Aspire 5516)

  - by Grand Master T

  Ubuntu 12.04-12.10 32/64 freezes or won't boot if the Ethernet cable is unplugged and will not hold a wireless connection. Here is my scenario... Laptop: Acer Aspire 5516 Wireless card: Broadcom BCM4312 Ubuntu 12.04 32/64 Issues Unity 3d won't load without the Ethernet cable plugged in. If I let it load with Ethernet plugged in, it will freeze once I disconnect the cable. Unity 2d will load without the Ethernet cable plugged. In Unity 2d, wireless cannot hold a connection. I can connect to a Wireless network, but when I try to use it (i.e. open a browser), it disconnects. I can reconnect by disabling wireless (uncheck Enable Wireless), re-enable wireless, and reconnect. But, it will disconnect again once I start using it. Ubuntu 12.10 Issues Since 12.10 only gives me the option to load 3d (I assume), I experience the same thing as the first issue in 12.04. Attempted Solutions Enable networking/LAN in BIOS Set LAN first in boot priority in BIOS Remove STA wireless driver (bcmwl-kernel-source) and install b43 low power driver (firmware-b43-lpphy-installer). Remove default Network Manager and install Wicd. So far, I have had no luck with fixing this issue. Does anyone have any further suggestions?

  Read the article

• Worthless Anti-Spam (What can we learn)

  - by smehaffie

  I recently can across a site that had a “anti-spam” field at the bottom of the entry from.  The first issue I had with it was that at 1280X800 you could not read the value you were suppose to enter (see below).  You tell me, should you enter div, dlv, piv, or plv. But even worse than not being readable at high resolutions is the fact that the programmer who coded it really did not understand what this was used for.  An anti-spam (aka: catpcha) entry field should not be able to be read by looking at the HTML DOM object (so entry of value cannot be scripted).  In this case the value is simply a disabled text input filed that has the value you need to type.  So a hacker would simply need to search for text input field named “spam2” and then they could flood the site with spam. 1: <td> 2: <label> 3: <input name="spam1" type="text" class="small" id="spam1" size="6" maxlength="3" /> 4: <input name="spam2" type="text" class="small" id="spam2" value="plv" 5: disabled="disabled" size="6" maxlength="3" /> 6: * <span class="small">- Anti-SPAM key - please enter matching value</span> 7: </label> 8: </td>   There are some things to learn from this example: 1) Always make sure you understand why you are coding a feature/function for any program you write.  Just following the requirements without realizing the “why” will sooner or later come back to bite you.  I think the above example appears to be an example of this. 2) Always check how the screen appears in different resolutions.  In this case it was pretty much unreadable in 1280x800, but you could read it in 800X600 (but most people I know do not have their resolution set that low).  Lucky for me I could “View Source” and get the value I needed to enter.

  Read the article

• Oracle Open World / Public Sector / Identity Platform

  - by user12604761

  For those attending Oracle Open World (Oct. 1st - 3rd, 2012 at the Moscone Center in San Francisco), the following details are recommended:  OOW Focus on Public Sector. Also, Oracle's foundational Identity and Access Management and Database Security products that support government security ICAM solutions are covered extensively during the event, the following will be available: The focus is on Oracle's Modern Identity Management Platform.   Integrated Identity Governance Mobile Access Management Complete Access Management Low Risk Upgrades The options for attendees include 18 sessions for Identity and Access Management, 9 Identity and Access Management demonstration topics at the Identity Management Demo Grounds, and 2 hands on labs, as well as 21 database security sessions. Oracle Public Sector Reception at OOW:  Join Oracle's Public Sector team on Monday, October 1 for a night of food and sports in a casual setting at Jillian’s, adjacent to Moscone Center on Fourth Street. In addition to meeting the Public Sector team, you can enjoy Monday Night Football on several big screen TVs in a fun sports atmosphere. When: Monday, October 1, 6:30 p.m.–9:30 p.m. Where: Jillian's, 101 Fourth Street, San Francisco 

  Read the article

• Software development company business plan

  - by Navi

  I apologize in advance if this is the wrong forum for this question, so please forward me to the right place. I have about 10 years professional experience as software developer. Mostly on the Java platform doing server side programs. I have picked up a bit of Linux skills on the way as well. I know HTML and Javascript, so I can make a website that would not be too ugly, but I am not going to win any prizes with it. In fact I think I am pretty terrible in the user interface department. My initial plan is to do Android development. I read a few Android books and tried making a few apps. Since it is Java based I think I got the technical side down. Lately I have been thinking about iphone and Mac development, because of the relevant app store/development programs. The trouble is I don't know Objective C. As a side question, how long would it take me to become proficient in Objective C? Considering that I am working on my own and could hire somebody to help me for a short time for low wages if necessary what are my options? What are the pro and cons of the development programs app stores of Android and Apple? Which development/app stores are out there beside the ones I mentioned? Do you think it is necessary to find funds to get me started or should I just use my savings? If you have positive/negative experiences in a similar situations can you please share them? Thanks for your help.

  Read the article

• How to ensure nvidia_current module loads during boot

  - by Aras

  I am running Ubuntu 12.10 on an Asus G75V laptop with nvidia gforce GTX 660M. I first run 12.04 on this machine and was able to install nvidia_current drivers from swat ppa: sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current This worked in 12.04 and after rebooting the machine my graphics where working properly. After upgrade to 12.10 however, the machine boots into a low resolution desktop which I can not really interact with. I suspect this is due to the driver not being loaded properly. To fix this, I have to switch to ctrl+alt+F1 session and manually load the nvidia_current module and restart the desktop manager: sudo modprobe nvidia_current sudo service lightdm restart Now everything works fine again. However, I would like not to have to do this every time I reboot the machine. I also dont want to hack an script to do this on load. Basically, if things are setup currectly, the nvidia_current driver which is installed should load. How can I make sure nvidia_current driver module loads properly when system starts?

  Read the article

• How do I fix broken installation?

  - by Daniel

  Let me start off by saying I'm dual booting 11.04 and Windows 7 on a Thinkpad T61p. The problem may have arisen when I hit the power button during normal startup. I'm fully aware how stupid this is. I don't know why I did it. I did it. Now, I can't get in to Ubuntu. Windows works fine. But when I try to start Ubuntu normally, it seems to run some checks, and does not start up. Sometimes, I see a black screen, and it tells me that it's running certain checks, and then, [ok]. Like... Battery Check Somethingorother [ok] It'll give me 1-5 of these. And then it just does nothing, and I have to turn it off. When I try to start in safe mode... I tried low graphics mode, and after going through a couple of dialogue boxes, I'm brought right back to the safe mode dialogue box. And if I hit 'resume,' a shell pushes up (still that grey on black "your computer is broken" type shell) and asks me to log in. I do, and try to run unity. It tells me something along the lines of: WARNING no DISPLAY variable set and then sets it to " :0" , which doesn't work. And then I can't do anything, really, and I have to restart. (I don't know how to do this from the command line, so I just hard reset. That command would be helpful). Does anybody have any idea how I can get Ubuntu working right again? FTP is less pleasant in Explorer than it is in Nautilus or w/e it is now.

  Read the article

• Is Akka a good solution for a concurrent pipeline/workflow problem?

  - by herpylderp

  Disclaimer: I am brand new to Akka and the concept of Actors/Event-Driven Architectures in general. I have to implement a fairly complex problem where users can configure a "concurrent pipeline": Pipeline: consists of 1+ Stages; all Stages execute sequentially Stage: consists of 1+ Tasks; all Tasks execute in parallel Task: essentially a Java Runnable As you can see above, a Task is a Runnable that does some unit of work. Tasks are organized into Stages, which execute their Tasks in parallel. Stages are organized into the Pipeline, which executes its Stages sequentially. Hence if a user specifies the following Pipeline: CrossTheRoadSafelyPipeline Stage 1: Look Left Task 1: Turn your head to the left and look for cars Task 2: Listen for cars Stage 2: Look right Task 1: Turn your head to the right and look for cars Task 2: Listen for cars Then, Stage 1 will execute, and then Stage 2 will execute. However, while each Stage is executing, it's individual Tasks are executing in parallel/at the same time. In reality Pipelines will become very complicated, and with hundreds of Stages, dozens of Tasks per Stage (again, executing at the same time). To implement this Pipeline I can only think of several solutions: ESB/Apache Camel Guava Event Bus Java 5 Concurrency Actors/Akka Camel doesn't seem right because its core competency is integration not synchrony and orchestration across worker threads. Guava is great, but this doesn't really feel like a subscriber/publisher-type of problem. And Java 5 Concurrency (ExecutorService, etc.) just feels too low-level and painful. So I ask: is Akka a strong candidate for this type of problem? If so, how? If not, then why, and what is a good candidate?

  Read the article

• Adding files and folders to a Root Folder (inode/directory)

  - by xBaldwin

  Ok so I'm fairly new to Ubuntu and wasn't even the one who put it one this computer(my friend did while I was storing it at his house because I was in the middle of transitioning between houses), but It's on here so I need to learn what I can so I can use it more effectively. My question at the moment is "Would it be safe to add files/folders to a folder (inode/directory) that requires Root access?" I continue to be informed by the system that the directory I am using is running low on space which I found odd seeing how I should have a lot more room on this computer. That's when I started looking at the directories and found that there are two with a bunch of un-used space on them. One says it has 46.9 GB of free space and the other has 24.9 GB of free space. Seems like a complete waste to not use that space and yet they both say they require Root access to add to them. I know that Root folders and files are normally all system folders and files. I also know that changing or deleting them can mess up the computer which right now I cant afford to do. I just don't know if it would mess anything up to add something to those folders. Thank you in advance to anyone who takes the time to reply and try to teach me about how all that works. I really do appreciate it and will do the same if by some crazy (completely unlikely) reason I have an answer to your question. :-)`

  Read the article

• Splitting a tetris game apart - where to put time-management?

  - by nightcracker

  I am creating a tetris game in C++ & SDL, and I'm trying to do it "good" by making it object-oriented and keeping scopes small. So far I have the following structure: A main with some lowlevel SDL set up and handling input A game class that keeps track of score and provides the interface for main (move block down, etc) A map class that keeps track of the current game field, which blocks are where. Used by the game class. A block class that consists of the current falling block, used by game. A renderer class abstracting low level SDL to a format where you render "tetris blocks". Used by map and block. Now I have a though time where to place the time-management of this game. For example, where should be decided when a block bumps the bottom of the screen how long it takes the current block locks in place and a new block spawns? I also have an other unrelated question, is there some place where you can find some standard data on tetris like standard score tables, rulesets, timings, etc?

  Read the article

• How to model the components of a non Information System?

  - by Adel C Kod

  So I am working on a project that's related to the Kernel code(specifically related to the TCP/IP stack of the kernel). I need to build some models to describe the functionality and components of my system. Initially I thought about Class Diagram, it can describe the general architecture of my system but it doesn't make sense since my code is VERY structured(written in standard C). I also thought about DFDs, they'd describe the processes of my system, and how the data is flowing. But they contain something which doesn't really fit in; data-storages. I have no databases here(at all). For the functionality, other team members suggested using Activity and Sequence diagrams, which is kinda okay with me, but what about the system components? So basically my question is; I want to describe the components of my system; what do you suggest as a meaningful diagram to follow? (Again, the project is a research low-level systems-oriented project with almost no user-interface at all)

  Read the article

• How can I configure the embedded wireless card in a Toshiba Satellite Pro 4600 to work under Lubuntu 10.10?

  - by MoLE

  I'm struggling to get the embedded wireless card in this laptop to work. In 7.10 (gutsy) it worked fine. Now I'm trying to get 10.10 (maverick) working on it, and am using the Lubuntu flavour due to the low resources of this laptop. The hardware: Appears to be an embedded pcmcia card. pccardctl ident gives: Socket 0: product info: "TOSHIBA", "Wireless LAN Card", "Version 01.01", "" manfid: 0x0156, 0x0002 function: 6 (network) The default kernel recognises the card and loads the orinoco_cs driver. orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0001:0006:000e orinoco_cs 0.0: Firmware determined as Lucent/Agere 6.14 Then for some reason, the driver isn't happy with this and gives: orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0002:0009:0030 orinoco_cs 0.0: Firmware determined as Lucent/Agere 9.48 All seems ok until I try to associate with my access point using Network Manager. eth1: Lucent/Agere firmware doesn't support manual roaming repeated about 10 times then NM gives up. According to the linuxwireless.org wiki page on this driver, this is a known issue, and I quote: Known issues Roaming and WPA_supplicant Lucent/Agere firmware doesn't support manual roaming On the Agere cards, roaming is controlled by the firmware instead of userspace. You will get the above message if userspace attempts to associate with a specific AP rather than by SSID. If you are using wpa_supplicant use ap_scan=2 mode. NetworkManager uses wpa_supplicant, so the above also applies. At this point my google-fu has failed me, and I can't find how to configure network manager to use the mystical "ap_scan=2" mode via wpa_supplicant. I have tried the following suggested solutions (from launchpad or the forums) deleting the agere* files from /lib/firmware using wicd instead of network manager combining both blacklisting the orinoco_cs driver in an attempt to force use of the hostap_cs driver instead (in case it is a prism2 card). Obviously none of them have worked for me. Any hints on how to perform the suggested workaround above? Edit: I have also confirmed working on 8.10 (intrepid) live CD.

  Read the article

• Any mobile-friendly Credit Card billing solutions for mobile sites similar to Bango?

  - by Programmer

  Are there any mobile-friendly Credit Card billing solutions for mobile sites similar to Bango? The advantages of Bango I have seen compared to regular Credit Card solutions that make it considerably "mobile-friendly" are: 1) It does not require the user to enter their full name and billing address to make a payment. The user is only required to enter their Credit Card number, expiration date, and CVC code (if they are in the U.S., they will also have to enter their Zip Code). That is significantly less input than is normally required for Credit Card payments, which is a big plus on small mobile key pads. After a user makes an initial Credit Card payment, their details are stored by Bango, and the next time the user needs to make a payment with the same Credit Card, they just have to click a single link and it processes the payment on their stored Credit Card. Needless to say, this is very convenient for mobile users as it is analogous to Direct Carrier Billing as far as the user is concerned since they won't need to input any details. The downside with Bango is that their fees are higher than others, all payments must be processed via their site and branding, there is a high minimum ($1.99) and a low maximum ($30) on how much you can charge users, and you need to pay a monthly fee on top of the high transaction costs. It is due to the downsides mentioned above that I am looking for an alternative solution that also does the advantages 1) and 2) above. Is there anything like that? I looked at JunglePay and they do neither 1) nor 2).

  Read the article

• 12.10 no audio via hdmi and video speeds up

  - by jackson

  I have a laptop with an ati radeon 4200, on 12.04 everything worked fine, since upgrading to 12.10 I cannot get sound over the hdmi. When I switch to hdmi audio the video speeds up to about 2x. I can use the speakers in my laptop and watch video via hdmi with no problems. Things I have tried: Various tutorials to install the AMD/ATI drivers, all of which resulted in low graphics mode. Checked that everything is properly set in alsamixer, the sound utility and - installed pavucontrol and checked everything in there. Verified the output from cat /proc/asound/cards looks normal When I initially upgraded there was a plethora of problems which I believe were due to the old proprietary driver still being used but not compatible, after a few hours trying to fix that I decided just to back up and do a fresh install which works great except for the above stated problem. Any help would be greatly appreciated!! Finally hopefully this hasn't already been answered, I have tried a few different searches on the boards and haven't come up with anything. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SB [HDA ATI SB], device 0: ALC269VB Analog [ALC269VB Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0] Subdevices: 0/1 Subdevice #0: subdevice #0

  Read the article

• Any examples of fair mmo games with quick completion

  - by Keith Player

  I'm looking for some example games for inspiration that allow from 10 to a large number of players at a time and can be completed in 10 to 30 minutes. I'm looking for something that would have extremely low bandwidth and not be dependent on chance or luck (i.e one player can't gain an unfair advantage because the computer put them in a better position). Realized on the way home that more clarifications might have been helpful. I'm looking to develop a pay-to-play competition that would allow a large number of players to compete in a relatively short period of time. One way would be to have an mmo that can be completed in 30 minutes, another way would be if you could have 10 person games that finish in under 5 minutes and then have the winners compete against each other until a winner is decided. I'm interested in any genre that would make for a fun/interesting game that doesn't depend on luck, so all players should have the same choice/availability of activities/resources and follow the same rules. Some possible games that could possibly be modified into what I want, would be bztanks (too easy to create a bot), diplomacy (takes too long), risk, some chess like game. I was just wondering if there are other game types to the ones I have been considering.

  Read the article

• X won't start, root filesystem mounted read only

  - by TK Kocheran

  I just experienced a very strange and puzzling problem on my machine that I can't seem to get sorted out. I was running Windows on a second partition, and everything was working great. I then went to restart into Linux, and noticed that X wouldn't start. Everything was displayed in super-low resolution, so I tried reinstalling my NVIDIA driver. I started seeing all of these I/O error problems, so I figured that my SSD was bad. After a bit more playing around, I ran fsck on the drive when mounted from a startup disk as well as badsectors and everything looked great. The SMART drive tests all passed and again, everything was looking good, so I rebooted again and still, no joy. I started then getting some weird USB errors, so I followed someone's advice and unplugged my computer's power supply, then started back up again and my graphics looked a lot better in the BIOS and in the boot logo, but X still wouldn't start. I then found out that my main boot drive was being mounted read-only for some reason. What's going wrong? I've done some pretty extensive tests on the SSD from a startup disk such as writing massive files, reading big files, running filesystem checks on the entire disk, and everything is looking great, until I try to boot. Whenever I try installing the drivers with apt-get, I get a ton of ata error messages looking like this: How can I diagnose what's going wrong and fix it so I can get back to work?

  Read the article

• UFW blocking random packets on 443

  - by s2jcpete

  All, I have UFW setup to allow traffic on port 443. It works as expected, though I have a large amount of UFW Block log entries. To Action From -- ------ ---- 80 ALLOW Anywhere 443 ALLOW Anywhere 22222 ALLOW Anywhere 80 ALLOW Anywhere (v6) 443 ALLOW Anywhere (v6) 22222 ALLOW Anywhere (v6) However in my syslog file I see this: [UFW BLOCK] IN=eth0 OUT= MAC=XXX SRC=<foreignip> DST=<serverip> LEN=40 TOS=0x00 PREC=0x00 TTL=116 ID=22025 DF PROTO=TCP SPT=49622 DPT=443 WINDOW=0 RES=0x00 ACK RST URGP=0 About 30 or so seconds later pound (which I'm using for SSL decryption and port redirection) throws a connection timed out messsage. I'm assuming this is because UFW is blocking the packet. I'm at a loss as to an explination. Could the packet be malformed or something, is this normal? Edit - I have since changed the /etc/defaults/ufw and set ipv6=no, so the v6 rules are no longer in the mix. The server is still showing the block / connection timed out behavior though. The new ufw status output is: Status: active Logging: on (low) Default: deny (incoming), allow (outgoing) New profiles: skip To Action From -- ------ ---- 80 ALLOW IN Anywhere 443 ALLOW IN Anywhere 22222 ALLOW IN Anywhere

  Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >