Monthly Archives

Articles indexed in June 2014

Page 93/211 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Ubuntu 14.04, only wallpaper and a mouse cursor is showing

  - by Abhishek Verma

  I upgraded to Ubuntu 14.04 weeks ago, that was a fresh install. And as usual installed, Unity tweak tool, some themes, Chrome, eclipse etc. Today, while playing with Unity tweak tool, I mistakenly switched Window spread to off, and bang, no problem yet. After realizing what I did I switched it to on again and then, the title bar of all windows, the status bar (guessing it's called that), and the launcher disappeared. Now I was left with a mouse cursor and the Unity tweak tool window, without the title bar. I thought a restart is needed, but sadly no shutdown option to click on, moreover, the keyboard didn't worked, neither the hardware shutdown button. So, I pressed the reset button. After a mundane restart, I was welcomed by the wallpaper and the mouse cursor, moving, that's it. Searched everywhere for a working solution, found some solutions in AskUbuntu itself, but they where all old and required terminal to be used, but since my keyboard isn't working, no access to the terminal. So, ofcource the question isn't a dublicate, at least, IMHO. Also, I was working on an Android project and have got no backups, so I won't be going for a clean install, or else I will start crying watching my weeks of work being deleted, any solutions, please.

  Read the article

• touchpad Detected but not working in Ubuntu 14.04 on toshiba satellite p75 a7200

  - by user288937

  I have a toshiba satalite that I have just installed Ubuntu 14.04 on and it runs great. But the touchpad does not work. I plugged in a usb mouse and it worked fine but the laptop touchpad wont work. I tried everything I could find under the sun and it is detected and all and says its enabled but does not work. I have pressed fn f7 to enable the mouse and still nothing. Synaptics is installed im pretty sure to because I used synaptics --list or something like that and It worked fine.

  Read the article

• How to run a bootable USB drive as my primary PC for an extended period?

  - by jason

  My hard drive has crashed, and I won't be able to buy a new one for a month or two. I've got a 16GB USB 3.0 flash drive that I'd like to have running a persistent ubuntu or ubuntu gnome distro. While it's not the best solution, is it a solution, or is it just a good way to wear out a flash drive? I plan on mostly storing things in Google Drive, so other than wearing out the flash drive, are there any risks involved?

  Read the article

• Ubuntu 14.04 Unity not functioning, no launcher

  - by user216962

  Yesterday I turned my computer to find that the launcher was missing. In addition, I could not using ctrl-alt-t would bring up a blank white screen. The only terminal could be found by clicking ctrl-alt-f1. I used ccsm to turn on Unity. Unity panel service was working. I installed tweak tool. I did all the troubleshooting I could find related to this subject. Nothing would work. I ultimately reinstalled Ubuntu 13.10. Also, I do not have an nvidia graphics card. I have an intel integrated graphics controller. Some of the troubleshooting I tried were found: Unity doesn't load, no Launcher, no Dash appears ubuntu 14.04 unity desktop without panel and launcher how to fix: no unity, no launcher no dash in ubuntu 14.04 http://ubuntuforums.org/showthread.php?t=2008891

  Read the article

• Error installing RVM

  - by Dbugger

  I am following this guide, but this is the output I receive. What am the problem? dbugger@mercury:~$ \curl -sSL https://get.rvm.io | bash -s stable --rails Downloading https://github.com/wayneeseguin/rvm/archive/stable.tar.gz Upgrading the RVM installation in /home/dbugger/.rvm/ RVM PATH line found in /home/dbugger/.profile /home/dbugger/.bashrc /home/dbugger/.zshrc. RVM sourcing line found in /home/dbugger/.bash_profile /home/dbugger/.zlogin. Upgrade of RVM in /home/dbugger/.rvm/ is complete. # Enrique, # # Thank you for using RVM! # We sincerely hope that RVM helps to make your life easier and more enjoyable!!! # # ~Wayne, Michal & team. In case of problems: http://rvm.io/help and https://twitter.com/rvm_io Upgrade Notes: * No new notes to display. rvm 1.25.27 (stable) by Wayne E. Seguin <[email protected]>, Michal Papis <[email protected]> [https://rvm.io/] Searching for binary rubies, this might take some time. No binary rubies available for: ubuntu/14.04/x86_64/ruby-2.1.2. Continuing with compilation. Please read 'rvm help mount' to get more information on binary rubies. Checking requirements for ubuntu. Installing requirements for ubuntu. Updating system.......... Installing required packages: gawk, libreadline6-dev, libssl-dev, libyaml-dev, libsqlite3-dev, sqlite3.... Error running 'requirements_debian_libs_install gawk libreadline6-dev libssl-dev libyaml-dev libsqlite3-dev sqlite3', showing last 15 lines of /home/dbugger/.rvm/log/1401804140_ruby-2.1.2/package_install_gawk_libreadline6-dev_libssl-dev_libyaml-dev_libsqlite3-dev_sqlite3.log ++ /scripts/functions/utility : __rvm_try_sudo() 405 > sudo -p '%p password required for '\''apt-get --no-install-recommends --yes install gawk libreadline6-dev libssl-dev libyaml-dev libsqlite3-dev sqlite3'\'': ' apt-get --no-install-recommends --yes install gawk libreadline6-dev libssl-dev libyaml-dev libsqlite3-dev sqlite3 Reading package lists... Building dependency tree... Reading state information... Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: libssl-dev : Depends: libssl1.0.0 (= 1.0.1f-1ubuntu2) but 1.0.1f-1ubuntu2.1 is to be installed E: Unable to correct problems, you have held broken packages. ++ /scripts/functions/utility : __rvm_try_sudo() 405 > return 100 ++ /scripts/functions/requirements/ubuntu : requirements_debian_libs_install() 36 > return 100 Requirements installation failed with status: 100.

  Read the article

• Usb/vga not recognized anymore

  - by Peter Raeves

  I don't know what happened, but yesterday everything worked fine, but when I woke up this morning and booted my computer to Ubuntu 14.04 a bunch of hardware isn't recognized anymore. I use a dual monitor setup with dvi-d and vga, but the vga screen isn't recognized anymore and the dvi-d monitor is recognized as "Built-in Display" while I'm not on a laptop. Also every device connected through usb isn't recognized anymore either. I have a keyboard with the blue round connector, which still works, so I can still log in though. The computer goes slower than usual and I have no idea what has happened. Can anybody point me in the direction I should start looking, because this is scary! I just checked and both the front and back sound connectors stopped working also :/ Edit: The devices connected through USB are recognized as they all show up using sudo lsusb, Ubuntu just doesn't let me use them anymore.

  Read the article

• Unity not Working 14.04

  - by Back.Slash

  I am using Ubuntu 14.04 LTS x64. I did a sudo apt-get upgrade yesterday and restarted my PC. Now my taskbar and panel are missing. When I try to restart Unity using unity --replace Then I get error: unity-panel-service stop/waiting compiz (core) - Info: Loading plugin: core compiz (core) - Info: Starting plugin: core unity-panel-service start/running, process 3906 compiz (core) - Info: Loading plugin: ccp compiz (core) - Info: Starting plugin: ccp compizconfig - Info: Backend : gsettings compizconfig - Info: Integration : true compizconfig - Info: Profile : unity compiz (core) - Info: Loading plugin: composite compiz (core) - Info: Starting plugin: composite compiz (core) - Info: Loading plugin: opengl compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Starting plugin: opengl libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/i965_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/i965_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/i965_dri.so failed (${ORIGIN}/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/i965_dri.so failed (/usr/lib/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: i965_dri.so libGL error: driver pointer missing libGL error: failed to load driver: i965 libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/swrast_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/swrast_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/swrast_dri.so failed (${ORIGIN}/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/swrast_dri.so failed (/usr/lib/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: swrast_dri.so libGL error: failed to load driver: swrast compiz (core) - Info: Loading plugin: compiztoolbox compiz (core) - Info: Starting plugin: compiztoolbox compiz (core) - Info: Loading plugin: decor compiz (core) - Info: Starting plugin: decor compiz (core) - Info: Loading plugin: vpswitch compiz (core) - Info: Starting plugin: vpswitch compiz (core) - Info: Loading plugin: snap compiz (core) - Info: Starting plugin: snap compiz (core) - Info: Loading plugin: mousepoll compiz (core) - Info: Starting plugin: mousepoll compiz (core) - Info: Loading plugin: resize compiz (core) - Info: Starting plugin: resize compiz (core) - Info: Loading plugin: place compiz (core) - Info: Starting plugin: place compiz (core) - Info: Loading plugin: move compiz (core) - Info: Starting plugin: move compiz (core) - Info: Loading plugin: wall compiz (core) - Info: Starting plugin: wall compiz (core) - Info: Loading plugin: grid compiz (core) - Info: Starting plugin: grid compiz (core) - Info: Loading plugin: regex compiz (core) - Info: Starting plugin: regex compiz (core) - Info: Loading plugin: imgpng compiz (core) - Info: Starting plugin: imgpng compiz (core) - Info: Loading plugin: session compiz (core) - Info: Starting plugin: session I/O warning : failed to load external entity "/home/sumeet/.compiz/session/10de541a813cc1a8fc140170575114755000000020350005" compiz (core) - Info: Loading plugin: gnomecompat compiz (core) - Info: Starting plugin: gnomecompat compiz (core) - Info: Loading plugin: animation compiz (core) - Info: Starting plugin: animation compiz (core) - Info: Loading plugin: fade compiz (core) - Info: Starting plugin: fade compiz (core) - Info: Loading plugin: unitymtgrabhandles compiz (core) - Info: Starting plugin: unitymtgrabhandles compiz (core) - Info: Loading plugin: workarounds compiz (core) - Info: Starting plugin: workarounds compiz (core) - Info: Loading plugin: scale compiz (core) - Info: Starting plugin: scale compiz (core) - Info: Loading plugin: expo compiz (core) - Info: Starting plugin: expo compiz (core) - Info: Loading plugin: ezoom compiz (core) - Info: Starting plugin: ezoom compiz (core) - Info: Loading plugin: unityshell compiz (core) - Info: Starting plugin: unityshell WARN 2014-06-02 18:46:23 unity.glib.dbus.server GLibDBusServer.cpp:579 Can't register object 'org.gnome.Shell' yet as we don't have a connection, waiting for it... ERROR 2014-06-02 18:46:23 unity.debug.interface DebugDBusInterface.cpp:216 Unable to load entry point in libxpathselect: libxpathselect.so.1.4: cannot open shared object file: No such file or directory compiz (unityshell) - Error: GL_ARB_vertex_buffer_object not supported ERROR 2014-06-02 18:46:23 unity.shell.compiz unityshell.cpp:3850 Impossible to delete the unity locked stamp file compiz (core) - Error: Plugin initScreen failed: unityshell compiz (core) - Error: Failed to start plugin: unityshell compiz (core) - Info: Unloading plugin: unityshell X Error of failed request: BadWindow (invalid Window parameter) Major opcode of failed request: 3 (X_GetWindowAttributes) Resource id in failed request: 0x3e000c9 Serial number of failed request: 10115 Current serial number in output stream: 10116 Any help would be highly appreciated. EDIT : My PC configuration description: Portable Computer product: Dell System XPS L502X (System SKUNumber) vendor: Dell Inc. version: 0.1 serial: 1006ZP1 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: administrator_password=unknown boot=normal chassis=portable family=HuronRiver System frontpanel_password=unknown keyboard_password=unknown power-on_password=unknown sku=System SKUNumber uuid=44454C4C-3000-1030-8036-B1C04F5A5031 *-core description: Motherboard product: 0YR8NN vendor: Dell Inc. physical id: 0 version: A00 serial: .1006ZP1.CN4864314C0560. slot: Part Component *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A11 date: 05/29/2012 size: 128KiB capacity: 2496KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot smartbattery biosbootspecification netboot *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 19 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: Not Supported by CPU slot: CPU size: 800MHz capacity: 800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts nopl xtopology nonstop_tsc aperfmperf eagerfpu pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=4 threads=8 *-cache:0 description: L1 cache physical id: 1a slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: synchronous internal write-through data *-cache:1 description: L2 cache physical id: 1b slot: L2-Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through data *-cache:2 description: L3 cache physical id: 1c slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: synchronous internal write-back unified *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 6GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: M471B5273DH0-CH9 vendor: Samsung physical id: 0 serial: 450F1160 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 0CA0E8E2 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:3000(size=4096) memory:f0000000-f10fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:f0000000-f0ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:3000(size=128) memory:f1000000-f107ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:52 memory:f1400000-f17fffff memory:e0000000-efffffff ioport:4000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei_me latency=0 resources: irq:50 memory:f1c05000-f1c0500f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:16 memory:f1c09000-f1c093ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:53 memory:f1c00000-f1c03fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode cap_list configuration: driver=pcieport resources: irq:16 *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 memory:f1b00000-f1bfffff *-network description: Wireless interface product: Centrino Wireless-N 1030 [Rainbow Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 34 serial: bc:77:37:14:47:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-27-generic firmware=18.168.6.1 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:f1b00000-f1b01fff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:19 memory:f1a00000-f1afffff *-usb description: USB controller product: uPD720200 USB 3.0 Host Controller vendor: NEC Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:f1a00000-f1a01fff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:f1900000-f19fffff *-pci:5 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 ioport:2000(size=4096) ioport:f1800000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 06 serial: 14:fe:b5:a3:ac:40 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=172.19.167.151 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:49 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:23 memory:f1c08000-f1c083ff *-isa description: ISA bridge product: HM67 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: driver=lpc_ich latency=0 resources: irq:0 *-ide:0 description: IDE interface product: 6 Series/C200 Series Chipset Family 4 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40b8(size=8) ioport:40cc(size=4) ioport:40b0(size=8) ioport:40c8(size=4) ioport:4090(size=16) ioport:4080(size=16) *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:f1c04000-f1c040ff ioport:efa0(size=32) *-ide:1 description: IDE interface product: 6 Series/C200 Series Chipset Family 2 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.5 bus info: pci@0000:00:1f.5 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40a8(size=8) ioport:40c4(size=4) ioport:40a0(size=8) ioport:40c0(size=4) ioport:4070(size=16) ioport:4060(size=16) *-scsi:0 physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: SAMSUNG HN-M640M physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 2AR1 serial: S2T3J1KBC00006 size: 596GiB (640GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=6b746d91 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: 0272-3e7f size: 348MiB capacity: 350MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2013-09-18 12:20:45 filesystem=ntfs label=System Reserved modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 116GiB capacity: 116GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 6037MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 110GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 logical name: /media/os version: 3.1 serial: 4e7853ec-5555-a74d-82e0-9f49798d3772 size: 156GiB capacity: 156GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-19 09:19:00 filesystem=ntfs label=OS mount.fstype=fuseblk mount.options=ro,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/data version: 3.1 serial: 7666d55f-e1bf-e645-9791-2a1a31b24b9a size: 322GiB capacity: 322GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-17 23:27:01 filesystem=ntfs label=Data modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-scsi:1 physical id: 2 logical name: scsi1 capabilities: emulated *-cdrom description: DVD-RAM writer product: DVD+-RW GT32N vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/sr0 version: A201 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-battery product: DELL vendor: SANYO physical id: 1 version: 2008 serial: 1.0 slot: Rear capacity: 57720mWh configuration: voltage=11.1V `

  Read the article

• How do I enable or disable the global application menu?

  - by Michael Ekstrand

  I'm fairly excited for Unity, as it looks like a promising new direction for Ubuntu. However, I do have a concern - will it be possible to use Unity without the global menu? I have my window manager set to focus-follows-mouse/sloppy focus, and find the productivity gains to be immense. Sloppy focus is incompatible, however, with global menus, as it is possible for the focus to change while you move from window to menu. Will Unity support an option to use window menus while still using Unity?

  Read the article

• Update pizza orders list [on hold]

  - by tirengarfio

  I have to create a website to order pizzas using PHP, MySQL, javascript, etc. I have to create also an android app for the owner of the restaurant, so when someone order a pizza, the android app show the new order on the list of the orders. Hwo to do this? Should I use push notifications? If yes, what happens when the connection su**s and the device is not connected at the moment of the push? Or should I use pull requests from the android device like every 10 seconds?

  Read the article

• How to pass information across domains to ask for newsletter only once?

  - by Michal Stefanow

  Lets assume following scenario, I have two sites: example1.com example2.com When user visits 1 there is a prompt "please signup to a newsletter". Same thing happens when user visits 2. However when navigating from 1 to 2 I don't want signup form to be shown. My first thought were 3rd-party cookies, but it seems that they are blocked / not working: http://stackoverflow.com/questions/4701922/how-does-facebook-set-cross-domain-cookies-for-iframes-on-canvas-pages?rq=1 http://stackoverflow.com/questions/172223/how-do-i-set-cookies-from-outside-domains-inside-iframes-in-safari?rq=1 Another thought is to append #noshow for each URL but that would require some work - for instance a script that would intercept click / tap events and modify URL structure depending on the address. (but that seems hacky) I wonder if you know a robust well-established solution to this issue? Thanks

  Read the article

• Author Bio on all pages - Is it duplicate content?

  - by Rana Prathap

  In a website with user generated content, I provide a author bio under every article on the site. The author bio will be the same under every article the same author wrote. For some authors, the author bio is no longer then a couple of sentences, but for some descriptive writers, it is a good 100 words. These 100 words get repeated in almost 15 pages, some of them without substantial original content(such as haikus). Will this lead to duplicate content?

  Read the article

• Should a website be on a topic?

  - by Rana Prathap

  I run an online writers' community where authors publish their literature works and other members of the community read and comment on them. The authors write a wide variety of literature pieces(such as haikus, stories, poems, scientific articles, personal narratives) on a wide variety of topics(about sun and anything under it). My intention of providing the authors with search engine traffic is largely affected by the non existence of topical focus of the website(or so I think). Is there a way to overcome this problem?

  Read the article

• All articles with infinite scroll, or one per page for usability and SEO?

  - by Rana Prathap

  Imagine a hypothetical website with all user generated content of single page articles. Here are some ways to structuring such a website: Putting up more than one article in one page and creating an infinite scroll or a pager. The fact that the articles may not be on the same topic makes this a less search engine friendly way. Giving a unique page to each article and putting up a list of links/titles in the front page with or without a teaser and a thumbnail. This might make the home page look unprofessional. Keeping the front page clean, without direct links to internal pages. Which method would be a search engine friendly and user friendly way to do this?

  Read the article

• Backlinks for nonexisting page

  - by Michal

  I've bought domain, which was previously used by somebody back in 2007. Now I've realized that internet is full of backlinks that point to non-existing parts (pages) under my website-domain (for example to mypage.com/whatever, where whatever is not present on my website, so 404 error shows). I want to ask, are these links counted by google (for pagerank) and other search engines, or not. So do I have to redirect these links to existing pages in order to be counted?

  Read the article

• VPNs - The ins and outs of IPSec & VPNs in general [on hold]

  - by Magus

  I have to decided to mess around with VPNs on my home router, to access a couple of servers in the back room of my house, however, I went into this thinking happy thoughts and easy-peasy-lemon-squeezy... Now I feel like doing drugs, as if maybe that will help me understand the myriad of terms which come with this nifty little tool. Basically, I do understand WHAT a VPN is, but I have no idea how to set one up. I have a Cisco router ( will supply more info if needed ), and would prefer to use IPSec for this ordeal. I'd like to have the following terms explained ( and yes, I have used the famous Google to help, close but no cigar ) : "Local Secure Group", "Remote Secure Group", "Remote Secure Gateway", how different types of "Keys" work ( again, I know the basics ), and for the "Add VPN Config" screen on the connecting device: "Server, does it have to be an address, or just an IP?", "Account; is this the tunnel name?", I am going to assume 'Password' means the Key, "Group Name; or is THIS the tunnel name?", and "Secret; I halfish know what this is..." I would really appreciate any contribution made, no matter how small, even if it includes a redirect. I just want to learn. Thanks in advance! Magus

  Read the article

• cloudflare's mx record should set cname or A records

  - by user7787

  The cloudflare offical support said https://support.cloudflare.com/hc/en-us/articles/200168876-My-email-or-mail-stopped-working-What-should-I-do- But traditionally mx record should not set as cname http://www.exchangepedia.com/blog/2006/12/should-mx-record-point-to-cname-records.html But cloudflare has a service called "cname Flattening" is it related for a reason to set cname as mx records? So should i set cloudflare's mx record as cname ?

  Read the article

• Using Google Analytics to determine how much time a visitor spends in each section of my site

  - by flossfan

  I have a site with various pages, like: /about/history /about/team /contact/email-us /contact I want to figure out how much time people are spending on the entire /about section, and how much on the /contact section. If I run a query on the Google Analytics API and set the dimension to ga:pagePathLevel1 and the metric to ga:avgTimeOnPage, I get results like this: { pagePathLevel1: /about, avgTimeOnPage: 28 }, { pagePathLevel1: /contact, avgTimeOnPage: 10 } This looks roughly like what I want, but I'm not sure how to intepret it: Is the value of avgTimeOnPage the average time spent by any user on all pages that match that path? Or is it the average time spent by any user on any single page that matches that path? I'm looking for the average time spent across all pages matching that path, but the time estimates look shorter than I'd expect.

  Read the article

• Should mobile webpages have hreflang links to non-mobile pages?

  - by Noam

  My site has multilingual links, which are specified like this on non-mobile pages: <link rel="alternate" hreflang="en" href="http://mydomain.com/page" /> <link rel="alternate" hreflang="jp" href="http://ja.mydomain.com/page" /> <link rel="alternate" hreflang="ko" href="http://ko.mydomain.com/page" /> In addition, these non-mobile pages link to a mobile version: <link rel="alternate" media="only screen and (max-width: 640px)" href="/mobile/page" /> Now the question is about what links should be in the mobile page, which isn't translated to different languages now. Is this enough: <link rel="canonical" href="/page"/> Or should I also have the same group of hreflangs that point to non-mobile pages?

  Read the article

• Linking one uniform variable to many shaders

  - by Winged

  Let's say, that I have 3 programs, and in each of those programs there is a view matrix uniform, which should be the same in all those programs. Right now, when my camera moves, I need to re-upload the modified matrix to every program separately. Is it possible to create some kind of global uniforms which are constant for all programs linked to it, so I could just upload the matrix once? I tried creating a globalUniforms object which looked kinda like this: var globalUniforms = { program: {}, // (...) vMatrixUniform: null, // (...) initialize: function() { vMatrixUniform = gl.getUniformLocation(this.program, 'uVMatrix'); } }; So I could just link it to proper programs like this: program.vMatrixUniform = globalUniforms.vMatrixUniform;, and then pass the matrix like this: if (camera.isDirty.viewMatrix !== false) { camera.isDirty.viewMatrix = false; gl.uniformMatrix4fv(globalUniforms.vMatrixUniform, false, camera.viewMatrix.element); } but unfortunately it throws an error: Uncaught exception: gl.INVALID_VALUE was caused by call to: getUniformLocation called from line 272, column 2 in () in mysite/js/mesh.js: vMatrixUniform = gl.getUniformLocation(this.program, 'uVMatrix'); Summing up: is there a more efficient way of managing shaders which follows my logic?

  Read the article

• how to make game objects to contain other objects?

  - by user3161621

  Im pretty undecided about what path to take here. The simplest that comes to mind is just adding a field List to the GameObject class where i would store the things contained in it. But would it be elegant and well tought? And would it be good performance wise?(ofc 99.9% of my objects wouldnt have anything stored in them...) What about deriving a ContainerObject from GameObject? This way only they would have additional fields but then i would have to change many things, my collections of objects would have to become a generic and id have to cast very often into GameObject...

  Read the article

• Converting a WIndows Store App to Android

  - by pm_2

  I cross posted this from SO I'm very new to Xamarin. I have a few published Windows Store apps and want to convert them to Android. I'm attempting to use Xamarin for this. I'm just using the free version of Xamarin. Here's where I am so far: I am trying two apps - one was build with Monogame and one is just build on the WinRT framework. I have managed to get them both into Xamarin studio, basically by hacking the csproj files. I'm getting build errors because it's missing references. There does appear to be some equivalent Mono / .Net4 libraries, but things like Microsoft.Xna.Framework seem to be missing. So, my question is: am I going about this the right way and, if so, am I missing a step ("convert dependencies" or something)? If I'm not going about this the right way then how should I be doing this (I found very few online resources on this subject)?

  Read the article

• Android-Libgdx-ProGuard: Usefulness without DexGuard? [on hold]

  - by Rico Pablo Mince

  So I'm developing a game for Android - using LibGDX - and noticed that the Android SDK (HDK, MDK, WhatTheHellEvarDK) has ProGuard built-in. Browsing the ProGuard page is like searching Google: you get that the idea is to sell some product (in this case, it's DexGuard). That leaves me wondering what features are left out of ProGuard that a game developer targeting Android should worry about. For instance, the ProGuard FAQs answer the question: "Does ProGuard encrypt string constants?" by saying: "No. String encryption in program code has to be perfectly reversible by definition, so it only improves the obfuscation level. It increases the footprint of the code. However, by popular demand, ProGuard's closed-source sibling for Android, DexGuard, does provide string encryption, along with more protection techniques against static and dynamic analysis." Alright. OK. But isn't "...improves the obfuscation level" EXACTLY what ProGuard is supposed to do? Are there better options that can be implemented at build-time in Eclipse using the Gradle options and Libgdx? In particular, the assets folder and res-specific folders will need some protection. The code itself doesn't cure cancer, but I'd prefer if nobody could copy/paste it with different game art and call it "IhAxEdUrGamE"....

  Read the article

• Approaches for a clickable map of nations (such as a Risk game) with Spritekit

  - by Vukovitch

  I would like to create a political map where each country is clickable by tapping but I'm not sure the best way to determine which nation was selected. Imagine Risk where each country can be individually clicked to bring up additional information. My current approach is to make a sprite for each nation where every image is the size of the screen The images are mostly transparent except for the country, that way when all of the images are displayed the countries are in the correct place relative to one another. To determine if a click occurs on an individual country I look to see if the tapped location is a non transparent pixel and check that the sprite's name is one of the countries. Additionally the nation needs to glow or something when tapped as an indicator, however my current solution is yet another sprite that is displayed. This seems like a terrible approach and I was wondering what other solutions might achieve the same results. I'm pretty new to SpriteKit so I'm not entirely sure. The other idea I had was creating a single texture where each country is a different shade of gray, then when I get the tap location I do a lookup on the color at that location and get the corresponding country. However, I'm not sure how to create a hilight or glowing country effect with that method.

  Read the article

• How do I create a camera?

  - by Morphex

  I am trying to create a generic camera class for a game engine, which works for different types of cameras (Orbital, GDoF, FPS), but I have no idea how to go about it. I have read about quaternions and matrices, but I do not understand how to implement it. Particularly, it seems you need "Up", "Forward" and "Right" vectors, a Quaternion for rotations, and View and Projection matrices. For example, an FPS camera only rotates around the World Y and the Right Axis of the camera; the 6DoF rotates always around its own axis, and the orbital is just translating for a set distance and making it look always at a fixed target point. The concepts are there; implementing this is not trivial for me. SharpDX seems to have has already Matrices and Quaternions implemented, but I don't know how to use them to create a camera. Can anyone point me on what am I missing, what I got wrong? I would really enjoy if you could give a tutorial, some piece of code, or just plain explanation of the concepts.

  Read the article

• How to draw a spotlight in 3D

  - by RecursiveCall

  To be clear, I am not talking about the light result (the lit area) but the spotlight itself, like this The two common suggestions that I tried are 2D image and a 3D cone. The problem with the pre-regenerated 2D image is that it always look 2D and flat no matter how it is rotated in world space. The cone on the other hand is next to impossible to control when it comes to fade distance, it doesn't look soft (smooth) and it is expensive to compute.

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >