Search Results

Search found 8410 results on 337 pages for 'hardware reserved'.

Page 103/337 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

  • Intermittent internet connectivity

    - by Rob Oplawar
    UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

    Read the article

  • Gacutil.exe successfully adds assembly, but assembly not viewable in explorer. Why?

    - by Ben McCormack
    I'm running GacUtil.exe from within Visual Studio Command Prompt 2010 to register a dll (CatalogPromotion.dll) to the GAC. After running the utility, it says Assembly Successfully added to the cache, and running gacutil /l CatalogPromotionDll shows that the GAC contains the assembly, but I can't see the assembly when I navigate to C:\WINDOWS\assembly from Windows Explorer. Why can't I see the assembly in WINDOWS\assembly from Windows Explorer but I can see it using gacutil.exe? Background: Here's what I typed into the command prompt for VS Tools: C:\_Dev Projects\VS Projects\bmccormack\CatalogPromotion\CatalogPromotionDll\bin \Debuggacutil /i CatalogPromotionDll.dll Microsoft (R) .NET Global Assembly Cache Utility. Version 4.0.30319.1 Copyright (c) Microsoft Corporation. All rights reserved. Assembly successfully added to the cache C:\_Dev Projects\VS Projects\bmccormack\CatalogPromotion\CatalogPromotionDll\bin \Debuggacutil /l CatalogPromotionDll Microsoft (R) .NET Global Assembly Cache Utility. Version 4.0.30319.1 Copyright (c) Microsoft Corporation. All rights reserved. The Global Assembly Cache contains the following assemblies: CatalogPromotionDll, Version=1.0.0.0, Culture=neutral, PublicKeyToken=9188a175 f199de4a, processorArchitecture=MSIL Number of items = 1 However, the assembly doesn't show up in C:\WINDOWS\assembly.

    Read the article

  • StyleCop XML Documentation Header - Using 3 /// instead of 2 //

    - by Adam Jenkin
    I am using XML documentation headers on my c# files to pass the StyleCop rule SA1633. Currently, I have to use the 2 slash commenting rule to allow StyleCop to recognize the header. for example: // <copyright file="abc.ascx.cs" company="MyCompany.com"> // MyCompany.com. All rights reserved. // </copyright> // <author>Me</author> This works fine for StyleCop, however I would like to use the 3 slash commenting rule to enable visual studio to understand the comments as XML and provide the XML functionality (highlighting, auto indenting etc) /// <copyright file="abc.ascx.cs" company="MyCompany.com"> /// MyCompany.com. All rights reserved. /// </copyright> /// <author>Me</author> The problem is that when using 3 slashes, StyleCop no longer see's the header and throws the SA1633 warning. Is there anyway to configure stylecop to understand the header is contained in XML using 3 slashes? Thanks, Adam

    Read the article

  • UIViewerTableViewController.m:15: error: expected identifier before '*' token

    - by Aaron Levin
    I am new to objective-c programming. I come from a C# background. I am having problems with the following code I am writing for a proof of concept for an iPhone App: I am getting a number of compile errors but I think they are all due to the first error (could be wrong) - error: expected identifier before '*' token (@synthesize *lists; in the .m file) I'm not sure why my code is showing up the way it is in the view below the editor..hmm any way, any help would be appreciated. .m file // // Created by Aaron Levin on 4/19/10. // Copyright 2010 RonStan. All rights reserved. // import "UIViewerTableViewController.h" @implementation UIViewerTableViewController @synthesize *lists; @synthesize *icon; (void)dealloc { [Lists release]; [super dealloc]; } pragma mark Table View Methods //Customize number of rows in table view (NSInteger)tableView:(UITableView *) tableView numberOfRowsInSection: (NSInteger) section{ return self.Lists.Count; } //Customize the appearence of table view cells (UITableViewCell *) tableView(UITableView *)tableView cellForRowAtIndexPath:(NSIndexPath *) indexPath{ static NSString *CellIdentifier = @"Cell"; UITableView *Cell = [tablevView dequeueReusableCellWithIdentifier:CellIdentifier]; if(cell == nil){ cell = [[[UITableViewCell alloc] initWithStyle:UITableViewCellStyleDefault reuseIdentifier:CellIdentifier] autorelease]; } cell.textLabel.text = [[self.Lists objectAtIndex:indexPath.row] retain]; cell.imageView = self.Icon; cell.accessoryType = UITableViewCellAccessoryDisclosureIndicator; } @end .h file // // UIMyCardsTableViewController.h // MCS ProtoType v0.1 // // Created by Aaron Levin on 4/19/10. // Copyright 2010 RonStan. All rights reserved. // import @interface UIViewerTableViewController : UITableViewController { NSArray *lists; UIImage *icon; } @property (nonatomic,retain) NSArray *lists; @property (nonatomic,retain) UIImage *icon; @end

    Read the article

  • How to get skin tone color pixel in iPhone?

    - by aman-gupta
    Hi In my application I m using following way to get red pixel in a image // // PixelsAccessAppDelegate.h // PixelsAccess // // Created by Fortune1 on 14/04/10. // Copyright MyCompanyName 2010. All rights reserved. // import @class clsPixelAccess; NSUInteger numberOfRedPixels; NSUInteger numberOfRedPixels1; NSUInteger numberOfRedPixels2; NSUInteger numberOfRedPixels3; NSUInteger numberOfRedPixels4; NSUInteger numberOfRedPixels5; NSUInteger numberOfRedPixels6; NSUInteger numberOfRedPixels7; NSUInteger numberOfRedPixels8; NSUInteger numberOfRedPixels9; NSUInteger numberOfRedPixels10; NSUInteger numberOfRedPixels11; NSUInteger numberOfRedPixels12; NSUInteger numberOfRedPixels13; NSUInteger numberOfRedPixels14; NSUInteger numberOfRedPixels15; NSUInteger numberOfRedPixels16; NSUInteger numberOfRedPixels17; NSUInteger numberOfRedPixels18; NSUInteger numberOfRedPixels19; NSUInteger numberOfRedPixels20; NSUInteger numberOfRedPixels21; NSUInteger numberOfRedPixels22; NSUInteger numberOfRedPixels23; NSUInteger numberOfRedPixels24; NSUInteger numberOfRedPixels25; NSUInteger numberOfRedPixels26; NSUInteger numberOfRedPixels27; NSUInteger numberOfRedPixels28; NSUInteger numberOfRedPixels29; NSUInteger numberOfRedPixels30; NSUInteger numberOfRedPixels31; @interface PixelsAccessAppDelegate : NSObject { UIWindow *window; clsPixelAccess *obj; } @property (nonatomic, retain) IBOutlet UIWindow *window; -(IBAction)processImage:(id)sender; @end //////////////////// // // PixelsAccessAppDelegate.m // PixelsAccess // // Created by Fortune1 on 14/04/10. // Copyright MyCompanyName 2010. All rights reserved. // import "PixelsAccessAppDelegate.h" import "clsPixelAccess.h" @implementation PixelsAccessAppDelegate @synthesize window; (IBAction)processImage:(id)sender { NSUInteger retVal; obj = [[clsPixelAccess alloc] init]; NSInteger imageSend =[obj processImage1:[UIImage imageNamed:@"s.jpg"]]; NSInteger iamgeCall =[obj getPixelData:retVal]; NSUInteger *numberOfRedPixels = retVal; //lblPixelCount.text = [NSString stringWithFormat: @"There are %d red pixels in the image", numberOfRedPixels]; } (void)applicationDidFinishLaunching:(UIApplication *)application { // Override point for customization after application launch [window makeKeyAndVisible]; } (void)dealloc { [window release]; [super dealloc]; } @end /////////////// // // clsPixelsAccess.h // PixelsAccess // // Created by Fortune1 on 14/04/10. // Copyright 2010 MyCompanyName. All rights reserved. // import @interface clsPixelAccess : NSObject { } -(NSInteger) processImage1: (UIImage*) image; -(NSInteger)getPixelData:(NSUInteger *)pixelCount; @end ///////// // // clsPixelsAccess.m // PixelsAccess // // Created by Fortune1 on 14/04/10. // Copyright 2010 MyCompanyName. All rights reserved. // import "clsPixelAccess.h" import "PixelsAccessAppDelegate.h" @implementation clsPixelAccess struct pixel { //unsigned char r, g, b,a; Byte r, g, b, a; int count; }; -(NSInteger)getPixelData:(NSUInteger *)pixelCount { *pixelCount =numberOfRedPixels; return 1; } // Process the image and return the number of pure red pixels in it. (NSInteger) processImage1: (UIImage*) image { // Allocate a buffer big enough to hold all the pixels struct pixel* pixels = (struct pixel*) calloc(1, image.size.width * image.size.height * sizeof(struct pixel)); if (pixels != nil) { // Create a new bitmap CGContextRef context = CGBitmapContextCreate( (void*) pixels, image.size.width, image.size.height, 8, image.size.width * 4, CGImageGetColorSpace(image.CGImage), kCGImageAlphaPremultipliedLast ); //NSLog(@"1=%d, 2=%d, 3=%d", CGImageGetBitsPerComponent(image), CGImageGetBitsPerPixel(image),CGImageGetBytesPerRow(image)); if (context != NULL) { // Draw the image in the bitmap CGContextDrawImage(context, CGRectMake(0.0f, 0.0f, image.size.width, image.size.height), image.CGImage); NSUInteger numberOfPixels = image.size.width * image.size.height; NSMutableArray *numberOfPixelsArray = [[[NSMutableArray alloc] initWithCapacity:numberOfPixelsArray] autorelease]; NSLog( @"Pixel data %d", numberOfPixelsArray); /* NSMatrix *newMatrix = [[NSMatrix alloc] initWithFrame:NSMakeRect(138.0f, 85.0f, 0.0f, 0.0f) mode:NSRadioModeMatrix prototype:prototypeButtonCell numberOfRows: numberOfColumns:]; */ while (numberOfPixels &gt; 0) { if (pixels-&gt;r &gt; 0 &amp;&amp; pixels-&gt;r &lt;= 7) { numberOfRedPixels++; } NSLog( @"Red pixel data %d",numberOfRedPixels); if (pixels-&gt;r &gt;= 8 &amp;&amp; pixels-&gt;r &lt;= 15) { numberOfRedPixels1++; } NSLog( @"Red pixel data1 %d",numberOfRedPixels1); if (pixels-&gt;r &gt;= 16 &amp;&amp; pixels-&gt;r &lt;=23 ) { numberOfRedPixels2++; } NSLog( @"Red pixel data2 %d",numberOfRedPixels2); if (pixels-&gt;r &gt;= 24 &amp;&amp; pixels-&gt;r &lt;=31 ) { numberOfRedPixels3++; } NSLog( @"Red pixel data3 %d",numberOfRedPixels3); if (pixels-&gt;r &gt;= 32 &amp;&amp; pixels-&gt;r &lt;= 39) { numberOfRedPixels4++; } NSLog( @"Red pixel data4 %d",numberOfRedPixels4); if (pixels-&gt;r &gt;= 40 &amp;&amp; pixels-&gt;r &lt;= 47) { numberOfRedPixels5++; } NSLog( @"Red pixel data5 %d",numberOfRedPixels5); if (pixels-&gt;r &gt;= 48 &amp;&amp; pixels-&gt;r &lt;= 55) { numberOfRedPixels6++; } NSLog( @"Red pixel data6 %d",numberOfRedPixels6); if(pixels-&gt;r &gt;= 56 &amp;&amp; pixels-&gt;r &lt;= 63) { numberOfRedPixels7++; } NSLog( @"Red pixel data7 %d",numberOfRedPixels7); if (pixels-&gt;r &gt;= 64 &amp;&amp; pixels-&gt;r &lt;= 71) { numberOfRedPixels8++; } NSLog( @"Red pixel data8 %d",numberOfRedPixels8); if (pixels-&gt;r &gt;= 72 &amp;&amp; pixels-&gt;r &lt;= 79) { numberOfRedPixels9++; } NSLog( @"Red pixel data9 %d",numberOfRedPixels9); if (pixels-&gt;r &gt;= 80 &amp;&amp; pixels-&gt;r &lt;= 87) { numberOfRedPixels10++; } NSLog( @"Red pixel data10 %d",numberOfRedPixels10); if (pixels-&gt;r &gt;= 88 &amp;&amp; pixels-&gt;r &lt;= 95) { numberOfRedPixels11++; } NSLog( @"Red pixel data11 %d",numberOfRedPixels11); if (pixels-&gt;r &gt;= 96 &amp;&amp; pixels-&gt;r &lt;= 103) { numberOfRedPixels12++; } NSLog( @"Red pixel data12 %d",numberOfRedPixels12); if (pixels-&gt;r &gt;= 104 &amp;&amp; pixels-&gt;r &lt;= 111) { numberOfRedPixels13++; } NSLog( @"Red pixel data13 %d",numberOfRedPixels13); if (pixels-&gt;r &gt;= 112 &amp;&amp; pixels-&gt;r &lt;= 119) { numberOfRedPixels14++; } NSLog( @"Red pixel data14 %d",numberOfRedPixels14); if (pixels-&gt;r &gt;= 120 &amp;&amp; pixels-&gt;r &lt;= 127) { numberOfRedPixels15++; } NSLog( @"Red pixel data15 %d",numberOfRedPixels15); if (pixels-&gt;r &gt; 128 &amp;&amp; pixels-&gt;r &lt;= 135) { numberOfRedPixels16++; } NSLog( @"Red pixel data16 %d",numberOfRedPixels16); if (pixels-&gt;r &gt;= 136 &amp;&amp; pixels-&gt;r &lt;= 143) { numberOfRedPixels17++; } NSLog( @"Red pixel data17 %d",numberOfRedPixels17); if (pixels-&gt;r &gt;= 144 &amp;&amp; pixels-&gt;r &lt;=151) { numberOfRedPixels18++; } NSLog( @"Red pixel data18 %d",numberOfRedPixels18); if (pixels-&gt;r &gt;= 152 &amp;&amp; pixels-&gt;r &lt;=159 ) { numberOfRedPixels19++; } NSLog( @"Red pixel data19 %d",numberOfRedPixels19); if (pixels-&gt;r &gt;= 160 &amp;&amp; pixels-&gt;r &lt;= 167) { numberOfRedPixels20++; } NSLog( @"Red pixel data20 %d",numberOfRedPixels20); if (pixels-&gt;r &gt;= 168 &amp;&amp; pixels-&gt;r &lt;= 175) { numberOfRedPixels21++; } NSLog( @"Red pixel data21 %d",numberOfRedPixels21); if (pixels-&gt;r &gt;= 176 &amp;&amp; pixels-&gt;r &lt;= 199) { numberOfRedPixels22++; } NSLog( @"Red pixel data22 %d",numberOfRedPixels22); if(pixels-&gt;r &gt;= 184 &amp;&amp; pixels-&gt;r &lt;= 191) { numberOfRedPixels23++; } NSLog( @"Red pixel data23 %d",numberOfRedPixels23); if (pixels-&gt;r &gt;= 192 &amp;&amp; pixels-&gt;r &lt;= 199) { numberOfRedPixels24++; } NSLog( @"Red pixel data24 %d",numberOfRedPixels24); if (pixels-&gt;r &gt;= 200 &amp;&amp; pixels-&gt;r &lt;= 207) { numberOfRedPixels25++; } NSLog( @"Red pixel data25 %d",numberOfRedPixels25); if (pixels-&gt;r &gt;= 208 &amp;&amp; pixels-&gt;r &lt;= 215) { numberOfRedPixels26++; } NSLog( @"Red pixel data26 %d",numberOfRedPixels26); if (pixels-&gt;r &gt;= 216 &amp;&amp; pixels-&gt;r &lt;= 223) { numberOfRedPixels27++; } NSLog( @"Red pixel data27 %d",numberOfRedPixels27); if (pixels-&gt;r &gt;= 224 &amp;&amp; pixels-&gt;r &lt;= 231) { numberOfRedPixels28++; } NSLog( @"Red pixel data28 %d",numberOfRedPixels28); if (pixels-&gt;r &gt;= 232 &amp;&amp; pixels-&gt;r &lt;= 239) { numberOfRedPixels29++; } NSLog( @"Red pixel data29 %d",numberOfRedPixels29); if (pixels-&gt;r &gt;= 240 &amp;&amp; pixels-&gt;r &lt;= 247) { numberOfRedPixels30++; } NSLog( @"Red pixel data30 %d",numberOfRedPixels30); if (pixels-&gt;r &gt;= 248) { numberOfRedPixels31++; } NSLog( @"Red pixel data31 %d",numberOfRedPixels31); pixels++; numberOfPixels--; } CGContextRelease(context); } free(pixels); } return 1; } @end My problem is I want skin Tone Pixel how it could be possible Please help me out. Thanks in Advance

    Read the article

  • Error while dynamically loading mapi32.dll

    - by The_Fox
    Our application uses Simple MAPI to send e-mails. One of our clients has problems sending e-mail from a session on his terminal server. The mapi32.dll is loaded with a call to LoadLibrary which succeeds, but then our application tries to get the addresses of the functions MAPILogon, MAPILogOff, MAPISendMail, MAPIFreeBuffer and MAPIResolveName. The problem is that GetProcAddress fails for those functions with an ERROR_ACCESS_DENIED (code: 5) except for MAPIFreeBuffer. It looks like some sort of security thing. How can I fix this or should I use another method to send mail? FWI, here some more information about OS and contents of registry key HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows Messaging Subsystem: OS info: 5.2.3790 VER_PLATFORM_WIN32_NT Service Pack 2 Contents of SOFTWARE\Microsoft\Windows Messaging Subsystem InstallCmd: rundll32 setupapi,InstallHinfSection MSMAIL 132 msmail.inf MAPI: 1 CMCDLLNAME: mapi.dll CMCDLLNAME32: mapi32.dll CMC: 1 MAPIX: 1 MAPIXVER: 1.0.0.1 OLEMessaging: 1 Contents of SOFTWARE\Microsoft\Windows Messaging Subsystem\MSMapiApps inetsw95.exe: choosusr.dll: msab32.dll: nwab32.dll: outstore.dll: Microsoft Outlook CDOEXM.DLL: EMSMDB32.DLL: EMSABP32.DLL: newprof.exe: Microsoft Outlook outlook.exe: wfxmsrvr.exe: Microsoft Outlook msexcimc.exe: exchng32.exe: schdmapi.dll: Microsoft Outlook pilotcfg.exe: Microsoft Outlook mailmig.exe: Microsoft Outlook admin.exe: msspc32.dll: Microsoft Outlook cnfnot32.exe: Microsoft Outlook ilpilot.exe: Microsoft Outlook events.exe: I'm on Delphi 7.0, but that shouldn't matter. Edit, added version information: Fileversion info of C:\WINDOWS\system32\mapi32.dll Fileversion: 6.5.7226.0 FileDescription=Extended MAPI 1.0 for Windows NT CompanyName=Microsoft Corporation InternalName=MAPI32 Comments=Service Pack 1 LegalCopyRight=Copyright (C) 1986-2003 Microsoft Corp. All rights reserved. LegalTradeMarks=Microsoft(R) and Windows(R) are registered trademarks of Microsoft Corporation. OriginalFileName=MAPI32.DLL ProductName=Microsoft Exchange ProductVersion=6.5 Fileversion info of C:\Program Files\Common Files\SYSTEM\MSMAPI\1043\msmapi32.dll Fileversion: 11.0.5601.0 FileDescription=Extended MAPI 1.0 for Windows NT CompanyName=Microsoft Corporation InternalName=MAPI32.DLL LegalCopyRight=Copyright © 1995-2003 Microsoft Corporation. All rights reserved. OriginalFileName=MAPI32.DLL ProductName=MAPI32 ProductVersion=11.0.5601

    Read the article

  • Save UIwebview contents to photo gallery

    - by user307410
    There's a video tutorial on u tube that shows how to perform this.It consists of a UIwebview and toolbar button to save the contents.Haven't had any luck making this work.Could someone have a look and see they can make it work.Many thanks in advance. http://www.youtube.com/watch?v=gDPca3JIc_s&feature=player_embedded# /////////////////////////////////////////////////////////////////// // // SaveWebViewController.h // SaveWeb // // // Copyright MyCompanyName 2010. All rights reserved. // import @interface SaveWebViewController : UIViewController { IBOutlet UIWebView *webview; } @property (nonatomic, retain) IBOutlet UIWebView *webview; [IBAction]saveWeb:(id)sender; @end //////////////////////////////////////////////////////////////////////////////// // // SaveWebViewController.m // SaveWeb // // // Copyright MyCompanyName 2010. All rights reserved. // import "SaveWebViewController.h" @implementation SaveWebViewController (IBAction)saveWeb:(id)sender { UIGraphicsBeginImageContext(webView.frame.size); [self.view.layer renderInContext: UIGraphicsGetCurrentContext()]; UIImage *viewImage = UIGraphicsGetImageFromCurrentImageContext(); UIGraphicsEndImageContext(); UIImageWriteToSavedPhotosAlbum(viewImage, nil, nil, nil); } // The designated initializer. Override to perform setup that is required before the view is loaded. - (id)initWithNibName:(NSString *)nibNameOrNil bundle:(NSBundle *)nibBundleOrNil { if (self = [super initWithNibName:nibNameOrNil bundle:nibBundleOrNil]) { // Custom initialization } return self; } // Implement loadView to create a view hierarchy programmatically, without using a nib. - (void)loadView { } //Implement viewDidLoad to do additional setup after loading the view, typically from a nib. - (void)viewDidLoad { [super viewDidLoad]; [webView loadRequest:[NSURLRequest requestWithURL:[NSURL URLWithString:@"http://google.com"]]]; } // Override to allow orientations other than the default portrait orientation. - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { // Return YES for supported orientations return (interfaceOrientation == UIInterfaceOrientationPortrait); } (void)didReceiveMemoryWarning { // Releases the view if it doesn't have a superview. [super didReceiveMemoryWarning]; // Release any cached data, images, etc that aren't in use. } (void)viewDidUnload { // Release any retained subviews of the main view. // e.g. self.myOutlet = nil; } (void)dealloc { [super dealloc]; } @end

    Read the article

  • PartCover 2.5.3 win 7 x64

    - by user329814
    Could you tell me how you got PartCover running with VS2008 and win 7 x64? Based on this post http://stackoverflow.com/questions/256287/how-do-i-run-partcover-in-x64-windows, I ran c:\Program Files (x86)\Gubka Bob\PartCover .NET 2.3>CorFlags.exe PartCover.exe / 32BIT+ /Force with result Microsoft (R) .NET Framework CorFlags Conversion Tool. Version 3.5.21022.8 Copyright (c) Microsoft Corporation. All rights reserved. corflags : warning CF011 : The specified file is strong name signed. Using /Force will invalidate the signature of this image and will require the assembly to be resigned. and c:\Program Files (x86)\NUnit 2.5.2\bin\net-2.0>CorFlags.exe nunit.exe /32BIT+ /Force with result Microsoft (R) .NET Framework CorFlags Conversion Tool. Version 3.5.21022.8 Copyright (c) Microsoft Corporation. All rights reserved. Also, based on my discussion http://stackoverflow.com/questions/2546340/using-partcover-2-3-with-net-4-0-runtime/2964333#2964333, I also tried to use the x86 version of NUnit What I'm trying to run coverage for is the c# money sample for NUnit 2.5.2 I get the same System.Threading.ThreadInterruptedException --- System.Runtime.InteropServices.COMException (0x80040153): Retrieving the COM class factory for component with CLSID {FB20430E-CDC9-45D7-8453-272268002E08} failed due to the following error: 80040153 Thank you Edit: same thing with PartCover 2.2 My settings: exe file: C:\Program Files (x86)\NUnit 2.5.2\bin\net-2.0\nunit-console-x86.exe working dir: c:\Program Files (x86)\NUnit 2.5.2\samples\csharp\money\ work arg: /config=c:\Program Files (x86)\NUnit 2.5.2\samples\csharp\money\cs-money.csproj rules: +[]

    Read the article

  • Android USB driver for Xperia X10a

    - by mlohbihler
    I've been trying for a couple hours now, and have hit all of the sites Google found, but i cannot get the Android USB driver on my XP box to talk to my new Xperia X10a. I found the lines that some kind soul posted, and has been syndicated repeated, but they don't work for me. The idea is to add them to the Google.NTx86 and Google.NTamd64 sections of the android_winusb.inf file: ;Xperia X10 %SingleAdbInterface% = USB_Install, USB\VID_0FCE&PID_E12E %CompositeAdbInterface% = USB_Install, USB\VID_0FCE&PID_E12E&MI_01 I tried a number of variations of the first line, including "Sony Ericsson X10a", which is what XP shows me in both the "found new hardware" wizard and the device manager, but no luck. The result is always the same. Here are my steps: Plug in the phone via USB "found new hardware wizard" appears Choose "No, not this time" and "next" Choose "Install from a list or specific location..." and "next" Choose "Search for best driver...", check "Include this location...", and browse for the "usb_driver" folder in the Android SDK installation. Click "next" It does a quick search and then says "Cannot install this hardware", "... because the wizard cannot find the necessary software". I've tried more things that i can recall now, including deleting registry entries, but it just won't work. Any help would be appreciated at this point. Regards, m@

    Read the article

  • Getting snapshot from webcam in Matlab

    - by Harsh
    I have created a simple GUI to preview webcam stream and to get snapshot from it. For this I have created on axes to show video, one push button(pushbutton1) to start preview, one push button(pushbutton2) to get snapshot. Following is the code for these two push buttons. function pushbutton1_Callback(hObject, eventdata, handles) % hObject handle to pushbutton1 (see GCBO) % eventdata reserved - to be defined in a future version of MATLAB % handles structure with handles and user data (see GUIDATA) axes(handles.axes1); vidObj = videoinput('winvideo',1); videoRes = get(vidObj, 'VideoResolution'); numberOfBands = get(vidObj, 'NumberOfBands'); handleToImage = image( zeros([videoRes(2), videoRes(1), numberOfBands], 'uint8') ); preview(vidObj, handleToImage); % --- Executes on button press in pushbutton2. function pushbutton2_Callback(hObject, eventdata, handles) % hObject handle to pushbutton2 (see GCBO) % eventdata reserved - to be defined in a future version of MATLAB % handles structure with handles and user data (see GUIDATA) a=getsnapshot(get(axes,'Children')); imshow(a); In pushbutton2_Callback I am trying to get child of axes ie. vidObj. But this gives me error ??? Undefined function or method 'getsnapshot' for input arguments of type 'double'.. Why is it returing double type instead of child object vidObj? How can I fix it and get snapshot? Is there any other better way? (I just started learning GUI.) Thanks.

    Read the article

  • Practical size limitations for RDBMS

    - by grenade
    I am working on a project that must store very large datasets and associated reference data. I have never come across a project that required tables quite this large. I have proved that at least one development environment cannot cope at the database tier with the processing required by the complex queries against views that the application layer generates (views with multiple inner and outer joins, grouping, summing and averaging against tables with 90 million rows). The RDBMS that I have tested against is DB2 on AIX. The dev environment that failed was loaded with 1/20th of the volume that will be processed in production. I am assured that the production hardware is superior to the dev and staging hardware but I just don't believe that it will cope with the sheer volume of data and complexity of queries. Before the dev environment failed, it was taking in excess of 5 minutes to return a small dataset (several hundred rows) that was produced by a complex query (many joins, lots of grouping, summing and averaging) against the large tables. My gut feeling is that the db architecture must change so that the aggregations currently provided by the views are performed as part of an off-peak batch process. Now for my question. I am assured by people who claim to have experience of this sort of thing (which I do not) that my fears are unfounded. Are they? Can a modern RDBMS (SQL Server 2008, Oracle, DB2) cope with the volume and complexity I have described (given an appropriate amount of hardware) or are we in the realm of technologies like Google's BigTable? I'm hoping for answers from folks who have actually had to work with this sort of volume at a non-theoretical level.

    Read the article

  • one page filter results in new page in javascript

    - by Jake
    I have links set up on one page and the relationship between the links is a parent child relationship. (For example: Parent: All, Children: Software; Hardware) These links of course lead the user to a new page that shows the results from a table that is populated. Currently these links are all Similar destinations, but just a filter in the url. But the problem is that there is a javascript filter on the page that gives the user to choose between All, Software, or Hardware. Understand basically that if the url is still reading that there on the software page but they just filtered on the page to be Hardware that doesn't look good IMO. So what I was trying to do was make the links on the inital page all go the the exact same destination and somehow still know on the new page which link was clicked and run the javascript filter from knowing which link was clicked on that page. Is there a way to found that out from javascript? I guess a way to pass that value to the new page and retrieving it in javascript without showing it in the url so I can filter the table for the user based on that value?

    Read the article

  • How to "escape" the JavaScript class keyword to specify a CSS class value.

    - by Robert Claypool
    C# allows a reserved word to be used as a property name via the ampersand. e.g. // In ASP.NET MVC, we use @class to define // the css class attribute for some HtmlHelper methods. var htmlObject = new { readonly = "readonly", @class = "ui-state-highlight" } I want to do the same in JavaScript. e.g. function makeGrid(grid, pager) { grid.jqGrid({ caption: 'Configurations', colNames: ['Id', 'Name'], colModel: [ { name: 'Id', index: 'Id' }, { name: 'Name', index: 'Name', editable: true, editoptions: { readonly: 'readonly', class: 'FormElement readonly' } }, ], pager: pager, url: 'www.example.com/app/configurations") %>', editurl: 'www.example.com/app/configurations/edit") %>' }).navGrid(pager, { edit: true, add: false, del: false, search: false }, {}, {}, {}); } Note class: 'FormElement readonly' is supposed to set the css class value on jqGrid's edit dialog, but IE errors out on the reserved word. Is there an escape character in JavaScript too? #class? @class? &class? Otherwise, how might I tell jqGrid to set the css class on the popup editor? Thank you.

    Read the article

  • Anonymous union definition/declaration in a macro GNU vs VS2008

    - by Alan_m
    I am attempting to alter an IAR specific header file for a lpc2138 so it can compile with Visual Studio 2008 (to enable compatible unit testing). My problem involves converting register definitions to be hardware independent (not at a memory address) The "IAR-safe macro" is: #define __IO_REG32_BIT(NAME, ADDRESS, ATTRIBUTE, BIT_STRUCT) \ volatile __no_init ATTRIBUTE union \ { \ unsigned long NAME; \ BIT_STRUCT NAME ## _bit; \ } @ ADDRESS //declaration //(where __gpio0_bits is a structure that names //each of the 32 bits as P0_0, P0_1, etc) __IO_REG32_BIT(IO0PIN,0xE0028000,__READ_WRITE,__gpio0_bits); //usage IO0PIN = 0x0xAA55AA55; IO0PIN_bit.P0_5 = 0; This is my comparable "hardware independent" code: #define __IO_REG32_BIT(NAME, BIT_STRUCT)\ volatile union \ { \ unsigned long NAME; \ BIT_STRUCT NAME##_bit; \ } NAME; //declaration __IO_REG32_BIT(IO0PIN,__gpio0_bits); //usage IO0PIN.IO0PIN = 0xAA55AA55; IO0PIN.IO0PIN_bit.P0_5 = 1; This compiles and works but quite obviously my "hardware independent" usage does not match the "IAR-safe" usage. How do I alter my macro so I can use IO0PIN the same way I do in IAR? I feel this is a simple anonymous union matter but multiple attempts and variants have proven unsuccessful. Maybe the IAR GNU compiler supports anonymous unions and vs2008 does not. Thank you.

    Read the article

  • How to TDD Asynchronous Events?

    - by Padu Merloti
    The fundamental question is how do I create a unit test that needs to call a method, wait for an event to happen on the tested class and then call another method (the one that we actually want to test)? Here's the scenario if you have time to read further: I'm developing an application that has to control a piece of hardware. In order to avoid dependency from hardware availability, when I create my object I specify that we are running in test mode. When that happens, the class that is being tested creates the appropriate driver hierarchy (in this case a thin mock layer of hardware drivers). Imagine that the class in question is an Elevator and I want to test the method that gives me the floor number that the elevator is. Here is how my fictitious test looks like right now: [TestMethod] public void TestGetCurrentFloor() { var elevator = new Elevator(Elevator.Environment.Offline); elevator.ElevatorArrivedOnFloor += TestElevatorArrived; elevator.GoToFloor(5); //Here's where I'm getting lost... I could block //until TestElevatorArrived gives me a signal, but //I'm not sure it's the best way int floor = elevator.GetCurrentFloor(); Assert.AreEqual(floor, 5); } Edit: Thanks for all the answers. This is how I ended up implementing it: [TestMethod] public void TestGetCurrentFloor() { var elevator = new Elevator(Elevator.Environment.Offline); elevator.ElevatorArrivedOnFloor += (s, e) => { Monitor.Pulse(this); }; lock (this) { elevator.GoToFloor(5); if (!Monitor.Wait(this, Timeout)) Assert.Fail("Elevator did not reach destination in time"); int floor = elevator.GetCurrentFloor(); Assert.AreEqual(floor, 5); } }

    Read the article

  • Are Fortran control characters (carriage control) still implemented in compilers?

    - by CmdrGuard
    In the book Fortran 95/2003 for Scientists and Engineers, there is much talk given to the importance of recognizing that the first column in a format statement is reserved for control characters. I've also seen control characters referred to as carriage control on the internet. To avoid confusion, by control characters, I refer to the characters "1, a blank (i.e. \s), 0, and +" as having an effect on the vertical spacing of output when placed in the first column (character) of a FORMAT statement. Also, see this text-only web page written entirely in fixed-width typeface : Fortran carriage-control (because nothing screams accuracy and antiquity better than prose in monospaced font). I found this page and others like it to be not quite clear. According to Fortran 95/2003 for Scientists and Engineers, failure to recall that the first column is reserved for carriage control can lead to horrible unintended output. Paraphrasing Dave Barry, type the wrong character, and nuclear missiles get fired at Norway. However, when I attempt to adhere to this stern warning, I find that gfortran has no idea what I'm talking about. Allow me to illustrate my point with some example code. I am trying to print out the number Pi: PROGRAM test_format IMPLICIT NONE REAL :: PI = 2 * ACOS(0.0) WRITE (*, 100) PI WRITE (*, 200) PI WRITE (*, 300) PI 100 FORMAT ('1', "New page: ", F11.9) 200 FORMAT (' ', "Single Space: ", F11.9) 300 FORMAT ('0', "Double Space: ", F11.9) END PROGRAM test_format This is the output: 1New page: 3.141592741 Single Space: 3.141592741 0Double Space: 3.141592741 The "1" and "0" are not typos. It appears that gfortran is completely ignoring the control character column. My question, then, is this: Are control characters still implemented in standards compliant compilers or is gfortran simply not standards compliant? For clarity, here is the output of my gfortran -v Using built-in specs. Target: powerpc-apple-darwin9 Configured with: ../gcc-4.4.0/configure --prefix=/sw --prefix=/sw/lib/gcc4.4 --mandir=/sw/share/man --infodir=/sw/share/info --enable-languages=c,c++,fortran,objc,java --with-gmp=/sw --with-libiconv-prefix=/sw --with-ppl=/sw --with-cloog=/sw --with-system-zlib --x-includes=/usr/X11R6/include --x-libraries=/usr/X11R6/lib --disable-libjava-multilib --build=powerpc-apple-darwin9 --host=powerpc-apple-darwin9 --target=powerpc-apple-darwin9 Thread model: posix gcc version 4.4.0 (GCC)

    Read the article

  • How can I work around WinXP using ports 1025-5000 as ephemeral?

    - by Chris Dolan
    If you create a TCP client socket with port 0 instead of a non-zero port, then the operating system chooses any free ephemeral port for you. Most OSes choose ephemeral ports from the IANA dynamic port range of 49152-65535. However in Windows Server 2003 and earlier (including XP) Microsoft used ports 1025-5000 as the ephemeral range, according to their bind() documentation. I run multiple Java services on the same hardware. On rare occasions, this range collides with well-known ports that I use for other services (e.g. port 4160 for Jini discovery). While rare, this has caused real problems. Is there any easy way to tell Windows or Java to use a different port range for client sockets? Microsoft's docs indicate that I can change the high end of that range via the MaxUserPort TcpIP registry setting, but I see no way to change the low end. Update: I've made some progress on this. It looks like Microsoft has a concept of reserved ports that are exceptions to the ephemeral port range. There's a registry setting that lets you change this permanently and apparently there must be an API to do the same thing because there's a data structure that holds high/low values for reserved port ranges, but I can't find the actual function call anywhere... The registry solution may work, but now I'm fixated on this API.

    Read the article

  • Gacutil.exe successfully adds assembly, but assembly missing from GAC. Why?

    - by Ben McCormack
    I'm running GacUtil.exe from within Visual Studio Command Prompt 2010 to register a dll (CatalogPromotion.dll) to the GAC. After running the utility, it says Assembly Successfully added to the cache, and running gacutil /l CatalogPromotionDll shows that the GAC contains the assembly, but I can't see the assembly when I navigate to C:\WINDOWS\assembly from Windows Explorer. Why can't I see the assembly in WINDOWS\assembly from Windows Explorer but I can see it using gacutil.exe? Background: Here's what I typed into the command prompt for VS Tools: C:\_Dev Projects\VS Projects\bmccormack\CatalogPromotion\CatalogPromotionDll\bin \Debuggacutil /i CatalogPromotionDll.dll Microsoft (R) .NET Global Assembly Cache Utility. Version 4.0.30319.1 Copyright (c) Microsoft Corporation. All rights reserved. Assembly successfully added to the cache C:\_Dev Projects\VS Projects\bmccormack\CatalogPromotion\CatalogPromotionDll\bin \Debuggacutil /l CatalogPromotionDll Microsoft (R) .NET Global Assembly Cache Utility. Version 4.0.30319.1 Copyright (c) Microsoft Corporation. All rights reserved. The Global Assembly Cache contains the following assemblies: CatalogPromotionDll, Version=1.0.0.0, Culture=neutral, PublicKeyToken=9188a175 f199de4a, processorArchitecture=MSIL Number of items = 1 However, the assembly doesn't show up in C:\WINDOWS\assembly.

    Read the article

  • How is external memory, internal memory, and cache organized?

    - by goldenmean
    Consider a system as follows:= A hardware board having say ARM Cortex-A8 and Neon Vector coprocessor, and Embedded Linux OS running on Cortex-A8. On this environment, if there is some application - say, a video decoder is executing - then: How is it decided that which buffers would be in external memory, which ones would be allocated in internal SRAM, etc. When one says calloc/malloc on such system/code, the pointer returned is from which memory: internal or external? Can a user make buffers to be allocated to the memories of his choice (internal/external)? In ARM architectures, there is another memory called as Tightly coupled memory (TCM). What is that and how can user enable and use it? Can I declare buffers in this memory? Do I need to see the memory map (if any) of the hardware board to understand about all these different physical memories present in a typical hardware board? How much of a role does the OS play in distinguishing these different memories? Sorry for multiple questions, but i think they all are interlinked.

    Read the article

  • Communicating with all network computers regardless of IP address

    - by Stephen Jennings
    I'm interested in finding a way to enumerate all accessible devices on the local network, regardless of their IP address. For example, in a 192.168.1.X network, if there is a computer with a 10.0.0.X IP address plugged into the network, I want to be able to detect that rogue computer and preferrably communicate with it as well. Both computers will be running this custom software. I realize that's a vague description, and a full solution to the problem would be lengthy, so I'm really looking for help finding the right direction to go in ("Look into using class XYZ and ABC in this manner") rather than a full implementation. The reason I want this is that our company ships imaged computers to thousands of customers, each of which have different network settings (most use the same IP scheme, but a large percentage do not, and most do not have DHCP enabled on their networks). Once the hardware arrives, we have a hard time getting it up on the network, especially if the IP scheme doesn't match, since there is no one technically oriented on-site. Ideally, I want to design some kind of console to be used from their main workstation which looks out on the network, finds all computers running our software, displays their current IP address, and allows you to change the IP. I know it's possible to do this because we sell a couple pieces of custom hardware which have exactly this capability (plug the hardware in anywhere and view it from another computer regardless of IP), but I'm hoping it's possible to do in .NET 2.0, but I'm open to using .NET 3.5 or P/Invoke if I have to.

    Read the article

  • Table not created by Hibernate

    - by User1
    I annotated a bunch of POJO's so JPA can use them to create tables in Hibernate. It appears that all of the tables are created except one very central table called "Revision". The Revision class has an @Entity(name="RevisionT") annotation so it will be renamed to RevisionT so there is not a conflict with any reserved words in MySQL (the target database). I delete the entire database, recreate it and basically open and close a JPA session. All the tables seem to get recreated without a problem. Why would a single table be missing from the created schema? What instrumentation can be used to see what Hibernate is producing and which errors? Thanks. UPDATE: I tried to create as a Derby DB and it was successful. However, one of the fields has a a name of "index". I use @org.hibernate.annotations.IndexColumn to specify the name to something other than a reserved word. However, the column is always called "index" when it is created. Here's a sample of the suspect annotations. @ManyToOne @JoinColumn(name="MasterTopID") @IndexColumn(name="Cx3tHApe") protected MasterTop masterTop; Instead of creating MasterTop.Cx3tHApe as a field, it creates MasterTop.Index. Why is the name ignored?

    Read the article

  • Report Viewer Configuration error - In View Source of webpage

    - by sarada
    I found the following error message when I checked View source of the web page , but the web page works just fine. Our Test lead found the error while performing Assertion tests. Report Viewer Configuration Error The Report Viewer Web Control HTTP Handler has not been registered in the application's web.config file. Add <add verb=" * " path="Reserved.ReportViewerWebControl.axd" type = "Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> to the system.web/httpHandlers section of the web.config file, or add <add name="ReportViewerWebControlHandler" preCondition="integratedMode" verb="*" path="Reserved.ReportViewerWebControl.axd" type="Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> to the system.webServer/handlers section for Internet Information Services 7 or later Why is this error message coming up in view source.. Note:There is a div tag around this error message which has style="display:none" I am trying to find out why but everybody has only discussed this error message as one which is thrown in the webpage. The changes suggested to web.config are already present in our config file.

    Read the article

  • Using std::ifstream to load in an array of struct data type into a std::vector

    - by Sent1nel
    I am working on a bitmap loader in C++ and when moving from the C style array to the std::vector I have run into an usual problem of which Google does not seem to have the answer. 8 Bit and 4 bit, bitmaps contain a colour palette. The colour palette has blue, green, red and reserved components each 1 byte in size. // Colour palette struct BGRQuad { UInt8 blue; UInt8 green; UInt8 red; UInt8 reserved; }; The problem I am having is when I create a vector of the BGRQuad structure I can no longer use the ifstream read function to load data from the file directly into the BGRQuad vector. // This code throws an assert failure! std::vecotr quads; if (coloursUsed) // colour table available { // read in the colours quads.reserve(coloursUsed); inFile.read( reinterpret_cast(&quads[0]), coloursUsed * sizeof(BGRQuad) ); } Does anyone know how to read directly into the vector without having to create a C array and copy data into the BGRQuad vector?

    Read the article

  • How to programmatically set the text of a cell of database in VB.Net?

    - by manuel
    I have a Microsoft Access database file connected to VB.NET. In the database table, I have a 'No.' and a 'Status' column. Then I have a textbox where I can input an integer. I also have a button, which will change the data cell in 'Status' where 'No.' = txtTitleNo.Text(), when I click it. Let's say I want the 'Status' cell to be changed to "Reserved". What codes should I put in the BtnReserve_Click? Here is the code: Public Class theForm Dim con As New OleDb.OleDbConnection Dim ds As New DataSet Dim daTitles As OleDb.OleDbDataAdapter Private Sub theForm_Load(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles MyBase.Load con.ConnectionString = "Provider=Microsoft.Jet.OLEDB.4.0; Data Source=|DataDirectory|\db1.mdb" con.Open() daTitles = New OleDb.OleDbDataAdapter("SELECT * FROM Titles", con) daTitles.Fill(ds, "Titles") DataGridView1.DataSource = ds.Tables("Titles") DataGridView1.AutoResizeColumns() End Sub Private Sub BtnReserve_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles BtnReserve.Click Dim daReserve As OleDb.OleDbCommand For i As Integer = 1 TReservedo DataGridView1.RowCount() If i = Val(txtTitleNo.Text()) Then daReserve = New OleDb.OleDbCommand("UPDATE Titles SET Status = 'Reserved' WHERE No = '" & i & "'", con) daReserve.ExecuteNonQuery() End If Next Dim cb As New OleDb.OleDbCommandBuilder(daTitles) daTitles.Update(ds, "Titles") End Sub This code still does not change the 'Status'. What should I do?

    Read the article

  • google app engine atomic section???

    - by bokertov
    hi, Say you retrieve a set of records from the datastore (something like: select * from MyClass where reserved='false'). how do i ensure that another user doesn't set the reserved is still false? I've looked in the Transaction documentation and got shocked from google's solution which is to catch the exception and retry in a loop. Any solution that I'm missing - it's hard to believe that there's no way to have an atomic operation in this environment. (btw - i could use 'syncronize' inside the servlet but i think it's not valid as there's no way to ensure that there's only one instance of the servlet object, isn't it? same applies to static variable solution) Any idea on how to solve??? (here's the google solution: http://code.google.com/appengine/docs/java/datastore/transactions.html#Entity_Groups look at: Key k = KeyFactory.createKey("Employee", "k12345"); Employee e = pm.getObjectById(Employee.class, k); e.counter += 1; pm.makePersistent(e); This requires a transaction because the value may be updated by another user after this code fetches the object, but before it saves the modified object. Without a transaction, the user's request will use the value of counter prior to the other user's update, and the save will overwrite the new value. With a transaction, the application is told about the other user's update. If the entity is updated during the transaction, then the transaction fails with an exception. The application can repeat the transaction to use the new data. THANKS!

    Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >