Search Results

Search found 33445 results on 1338 pages for 'single instance storage'.

Page 1043/1338 | < Previous Page | 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050  | Next Page >

• Where is my VMware-ws FreeNAS CIFS(ZFS) bottle-neck?

  - by maka

  Background: I'm building a quiet HTPC + NAS that is also supposed to be used for general computer usage. I'm so far generally happy with things, it was just that I was expecting a little better IO performance. I have no clue if my expectations are unreal. The NAS is there as a general purpose file storage and as a media server for XBMC and other devices. ZFS is a requirement. Question: Where is my bottle-neck, and is there anything I can do config wise, to improve my performance? I'm thinking VM-disk settings could be something but I really have no idea where to go since I'm neither experienced with FreeNAS nor VMware-WS. Tests: When I'm on the host OS and copy files (from the SSD) to the CIFS share, I get around 30 Mbytes/sec read and write. When I'm on my laptop laptop, wired to the network, I get about the same specs. The test I've done are with a 16 GB ISO, and with about 200 MB of RARs and I've tried avoiding the RAM-cache by reading different files than the ones I'm writing ( 10 GB). It feels like having less CPU cores is a lot more efficient, since the resource manager in Windows reports less CPU-usage. With 4 cores in VMware, CPU usage was 50-80%, with 1 core it was 25-60%. EDIT: HD ActiveTime was quite high on SSD so I moved the page file, disabled hibernate and enabled Win DiskCache both on SSD and RAID. This resulted in no real performance difference for one file, but if i transferred 2 files the total speed went up to 50 Mbytes/s vs ~40. The ActiveTime avg also went down a lot (to ~20%) but has now higher bursts. DiskIO is on ~ 30-35 Mbytes/s avgs, with ~100Mb bursts. Network is on 200-250Mbits/s with ~45 active TCP connections. Hardware Asus F2A85-M Pro A10-5700 16GB DDR3 1600 OCZ Vertex 2 128GB SSD 2x Generic 1tb 7200 RPM drives as RAID0 (in win7) Intel Gigabit Desktop CT Software Host OS: Win7 (SSD) VMware Worksation 9 (SSD) FreeNAS 8.3 VM (20GB VDisk on SSD) CPU: I've tried 1, 2 and 4 cores. Virtualisation engine, Preferred mode: Automatic 10,24Gb ram 50Gb SCSI VDisk on the RAID0, VDisk is formatted as ZFS and exposed through CIFS through FreeNAS. NIC Bridge, Replicate physical network state Below are two typical process print-outs while I'm transfering one file to the CIFS share. last pid: 2707; load averages: 0.60, 0.43, 0.24 up 0+00:07:05 00:34:26 32 processes: 2 running, 30 sleeping Mem: 101M Active, 53M Inact, 1620M Wired, 2188K Cache, 149M Buf, 8117M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 102 0 50164K 10364K RUN 0:25 25.98% smbd 1897 root 6 44 0 168M 74808K uwait 0:02 0.00% python last pid: 2746; load averages: 0.93, 0.60, 0.33 up 0+00:08:53 00:36:14 33 processes: 2 running, 31 sleeping Mem: 101M Active, 53M Inact, 4722M Wired, 2188K Cache, 152M Buf, 5015M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 76 0 50164K 10364K RUN 0:52 16.99% smbd 1897 root 6 44 0 168M 74816K uwait 0:02 0.00% python I'm sorry if my question isn't phrased right, I'm really bad at these kind of things, and it is the first time I post here at SU. I also appreciate any other suggestions to something, I could have missed.

  Read the article

• Why would e-mail from our own domain not be forwarded to gmail

  - by netboffin

  To solve a problem with spam on our server we tried to forward e-mail from our dedicated server's mailserver(matrix smtp service) to gmail, but while most e-mails got through e-mail from our own domain all went missing. They weren't in the inbox or spam or anywhere else. We've had to go back to using the old system, which means my boss gets a huge amount of spam. We have a windows 2003 server with iis 6 and the matrix smtp service installed. I've toyed with the idea of installing a mail proxy like ASSP but it looks pretty complicated. We're hosting 20 domains on the server as well as our own which has an online shop whose payment system depends on email. I can't start playing around with complicated solutions when it could have disastrous consequences and I don't know enough to implement them safely. So my question has two parts: Part One: Why can't we forward e-mails from people using the same domain. If our domain was foobar.com then [email protected] can't receive from [email protected], but he can receive from everyone else. Part Two: Is there a really simple server side solution to spam that would work with matrix? For instance popfile?

  Read the article

• virtual machines, dual booting and data disks on SSD

  - by stevemarvell

  This is in planning, so if I've got the strategy wrong, please let me know. There are multiple questions here, but I think they all degenerate to the same answers. The hardware is a laptop with a single SSD. I'm trying to not lose the performance of the SSD. I plan a native dual booting Windows (plus cygwin) and Linux machine which is my BYOD and represents the development environment. I keep the codebase on a shared partition (though sometimes this is an external thunderbolt SSD) which can be natively "mounted" by whichever OS is in operation. I boot into one or the other environments depending on the task in hand. Sometime I have to develop with windows tools, but generally, Linux is my preferred development environment. It would be ideal if I could VM the other OS and run either in either. I'm going to assume, because I've not found a sensible VM based solution, that I have get samba involved to share the code partition between VMs. Is this going to blow my SSD performance in the VM? The client also supplies me with a VM for the target environment, usually linux. This is not often suited to development and is used for testing only. I normally keep two copies of this, one as a sandbox and one which I deploy to using the client's preferred method. I keep these VM snapshots on the shared partition. The latter is interacted with over the network and so has no disk sharing requirements. However, it would be useful for the sandbox to be able to "mount" the code base from the natively running OS. Is this samba or nfs again, depending on the native OS? Am I missing a trick which allows this to all work smoothly with all four environments running at once without loosing the SSD performance?

  Read the article

• Outlook 2010 on WinXP runs once then refuses to run again until reboot

  - by msorens

  Since I installed Outlook 2010 on a new machine (WinXP Pro SP3) a couple months back I have had an issue that is quite annoying: If I close Outlook then attempt to restart it I get a small pop-up saying only: "Cannot start Microsoft Outlook". I found one workaround, but not a terribly practical one: reboot. If I reboot then launch Outlook, it opens fine. Here is what I know: Since I can run Outlook just fine after a reboot, I do not see that a system restore, an OS reinstall, or the like would help. I tried "outlook.exe /resetnavpane" and "outlook.exe /safe" but those give the same error. There are no entries in the event log. There is no instance of Outlook appearing in the process list once I close the program, so it does not seem to be an alias for "outlook is already running". As far as I have found, my situation is unique among reports of similar incidents: I have uncovered no other reports saying Outlook would run fine the first launch or that a reboot would again allow it to run. Suggestions?

  Read the article

• effective back-up using Raid / Win7 back-up

  - by Job

  I have a stand-alone pc system with two 2 tb harddiscs, one of which configured as Raid1, i.e. mirorring. The operational drive is partitioned. I use an external 1 tb harddisc for back-up using Windows 7 back-up facility which will be swapped weekly and stored on other premises. I back-up all partitions AND allow a system back-up. All application software is on the C: partition. Questions: How can I see whether Raid1 is working; i.e. is doing its job. All I see now is a status message in the start-up procedure that says its status is normal. How can I see used or available space on Raid 1? The Win-7 backup allows for 1 schedule only as far as I can see. I want daily back-ups of data. However due to the single schedule I am forced to do the time-consuming system back-up and c: back-up as well. Is there a way to activate two schedules allowing a frequent (daily) data back-up and a system back-up with c: drive back-up on a say weekly basis? Of course it can be forced by hand but I am likely to forget that. I am not the programming type of person so looking for simple and controllable solutions. Thank you - any help is apreciated.

  Read the article

• Laptop authentication/logon via accelometer tilt, flip, and twist

  - by wonsungi

  Looking for another application/technology: A number of years ago, I read about a novel way to authenticate and log on to a laptop. The user simply had to hold the laptop in the air and execute a simple series of tilts and flips to the laptop. By logging accelerometer data, this creates a unique signature for the user. Even if an attacker watched and repeated the exact same motions, the attacker could not replicate the user's movements closely enough. I am looking for information about this technology again, but I can't find anything. It may have been an actual feature on a laptop, or it may have just been a research project. I think I read about it in a magazine like Wired. Does anyone have more information about authentication via unique accelerometer signatures? Here are the closest articles I have been able to find: Knock-based commands for your Linux laptop Shake Well Before Use: Authentication Based on Accelerometer Data[PDF] Inferring Identity using Accelerometers in Television Remote Controls User Evaluation of Lightweight User Authentication with a Single Tri-Axis Accelerometer Identifying Users of Portable Devices from Gait Pattern with Accelerometers[PDF] 3D Signature Biometrics Using Curvature Moments[PDF] MoViSign: A novel authentication mechanism using mobile virtual signatures

  Read the article

• How can I backup entire installations of a program, instead of just manually backing up individual f

  - by NoCatharsis

  It seems pretty straightforward to backup individual files, such as pictures, saved games, or settings files - just copy them straight over to your 2nd HDD or to an online service like DropBox. However, is there any way to backup entire installations of a program? For instance, my Firefox directory has a lot of personal customizations and add-ons. I don't want to go through each item and decide to back it up or let it go. So my next option is to copy out the entire directory for backup. But, if I copy the entire directory back onto the HD after a format, it is not an integrated installation and this seems like it could be troublesome. I would assume Windows cannot detect the directory for uninstallation, or would not let you choose Firefox as your default browser, right? I'm no pro, but this sounds like a bad idea. So my question is whether there is a good way to preserve all necessary files, while also preserving the full installation process of an application. This is not specific to Firefox - I would like to know how to do this for any application. Thank you.

  Read the article

• How ZFS handles online replacement in a RAID-Z (theoretical)

  - by Kevin

  This is a somewhat theoretical question about ZFS and RAID-Z. I'll use a three disk single-parity array as an example for clarity, but the problem can be extended to any number of disks and any parity. Suppose we have disks A, B, and C in the pool, and that it is clean. Suppose now that we physically add disk D with the intention of replacing disk C, and that disk C is still functioning correctly and is only being replaced out of preventive maintenance. Some admins might just yank C and install D, which is a little more organized as devices need not change IDs - however this does leave the array degraded temporarily and so for this example suppose we install D without offlining or removing C. Solaris docs indicate that we can replace a disk without first offlining it, using a command such as: zpool replace pool C D This should cause a resilvering onto D. Let us say that resilvering proceeds "downwards" along a "cursor." (I don't know the actual terminology used in the internal implementation.) Suppose now that midways through the resilvering, disk A fails. In theory, this should be recoverable, as above the cursor B and D contain sufficient parity and below the cursor B and C contain sufficient parity. However, whether or not this is actually recoverable depnds upon internal design decisions in ZFS which I am not aware of (and which the manual doesn't say in certain terms). If ZFS continues to send writes to C below the cursor, then we are fine. If, however, ZFS internally treats C as though it were gone, resilvering D only from parity between A and B and only writing A and B below the cursor, then we're toast. Some experimenting could answer this question but I was hoping maybe someone on here already knows which way ZFS handles this situation. Thank you in advance for any insight!

  Read the article

• Win7 - Opening "Programs and Features" as Admin from command line (logged in as regular user)

  - by user1741264

  We have Win7 machines on a domain that we'd like to open the "Programs and Features" control applet via the command line while a regular user is logged in. Heres the catch: I know how to do this using runas from command line BUT after "Programs and Features" opens, I dont truly have the ability to remove a program. I am told that I need to be an Admin to do so. Here are the commands I have tried: runas /user:%computername%\administrator cmd.exe then in the new cmd window running: control appwiz.cpl runas /user:%companydomain%\%domainadminacct% cmd.exe then in the new cmd window running: control appwiz.cpl runas /user:%computername%\administrator cmd.exe then in the new cmd window running: rundll32.exe shell32.dll,Control_RunDLL appwiz.cpl runas /user:%companydomain%\%domainadminacct% cmd.exe then in the new cmd window running: rundll32.exe shell32.dll,Control_RunDLL appwiz.cpl I have also tried all of the above as one long line of code instead of launching a cmd.exe as Admin As you can see, I have tried running the command using both a local admin account (Administrator) AND a domain admin account. I have alos tried launching the runas command as one long command (opening the "programs and features") AND 1st launching a cmd.exe with admin rights and THEN launching the "Prgrams and Features" window. The result is the same: The "Programs and Features" windows opens but when I try to perform an uninstall, I am told I need Admin rights. Thus I am lead to believe that this instance of "Programs and Features" is not truly being run as an admin I am trying to avoid logging the regular user out. I am also aware that every program has its own uninstaller, I do not want to uninstall that way. I want to use the uninstaller in "Programs and Features". Any help is appreciated.

  Read the article

• Group Policy for DNS Server Addresses

  - by John

  This question deals strictly with the methodology of using Active Directory to publish DNS settings and controlling the DNS server address order to domain attached clients. This is not asking about if this is the right function, role, or best use of group policy; but rather, how to make it work. I would like to be able to publish in group policy DNS addresses and possibly control the order in which the client consumes the addresses. I have tried following the information from this site without success. I set the following setting within group policy, but the client never shows the settings within the TCP/IP properties. Computer Configuration/Administrative Templates/Network/DNS Client/DNS Servers I did list them as a single space separated list. For example, the following: 192.168.0.1 192.168.10.3 192.168.34.2 192.168.2.67 192.168.56.99 192.168.99.23 This would be for Windows 7, Windows Server 2003, and Windows Server 2008 clients. I am not sure what I am doing wrong or how to get this to work. Am I missing a setting? Do I need to set something differently?

  Read the article

• DHCP Relay setup in ubuntu server

  - by jerichorivera

  I have a network appliance (QNO) that works as traffic load balancer and dhcp server. I would like to add a linux server in between the network appliance and the client computers. The linux server will be used to monitor bandwidth usage. My problem is I still want DHCP to be served by the network appliance so that load balancing will still work efficiently. We are afraid that if we setup the linux server as the DHCP server the network appliance will not be able to load balance the traffic if it only sees the linux server as a single client connecting to it. I've been searching all over for a tutorial on how to setup DHCP relay but have not found any. How do I setup DHCP relay on my linux server given there are two NICs attached to it, one connects the linux server to the network appliance and the other connects the linux server to the client computers. EDIT Router (DHCP) ---- [eth0] Linux Server (Relay agent) [eth1] ----- PC (network) Router IP is 192.168.0.100 eth0 is on DHCP eth1 is static 192.168.2.11 (if I need to change this I can) Tried to do dhcrelay -i eth1 192.168.0.100, but the PC was not getting any DHCP lease from the DHCP router. I might be missing something here.

  Read the article

• setting up tracd behind mod_proxy?

  - by FilmJ

  I'm having trouble setting up mod_proxy and tracd. Seems almost all the search results for this problem take me to the built-in trac documentation page that mentions it as an option. I have several VirtualServers already running on the box in question, so running tracd on port 80 or 443 is not an option, but I do want to make my trac server accessible on this machine without exposing an additional port via the firewall. Making things even more complicated is that I have multiple trac repositories being served by the same instance of tracd, and so I want to set it up so: http://trac.abc.com is proxy'd to localhost:8000/projects/abcproject, and http://trac.def.com is proxy'd to localhost:8000/projects/defproject. Currently, the setup I have below results in 100% 403 errors. The server is running as www-data and the directory where all trac files are stored is owned by www-data, AND tracd (as show below) is running as www-data, so not sure where it's getting hung up. The relevant configuration on /var/apache2/sites-enabled/trac.abc.com: ProxyPass / http://localhost:8000/abcproject ProxyPassReverse / http://localhost:8000/abcproject The relevant configuration on /var/apache2/sites-enabled/trac.def.com: ProxyPass / http://localhost:8000/defproject ProxyPassReverse / http://localhost:8000/defproject The command used to instantiate tracd: tracd -a defproject,/var/www/vhosts/trac-common/users.htdigest,DEFProject -a abcproject,/var/www/vhosts/trac-common/users.htdigest,ABCProject -p 8000 -b localhost -e /var/www/vhosts/trac-common/projects If I access the site at http://localhost:8000/ everything works fine, but if I try to access via any of the proxy'd hosts I end up with 403 at every turn. I've used mod_proxy successfully as described above for other servers, such as couchdb, so maybe this has to do with the headers sent by tracd??

  Read the article

• ubuntu 9.04 pptp broken after a power failure

  - by kevin42

  I have a small Ubuntu 9.04 router setup as a NAT box and a PPTP server. After a power failure everything except the PPTP server still works. A windows client gets to "registering your computer on the network" but then says Error 742: The remote computer does not support the required data encryption type. I did some research and I think the problem is with the ppp_mppe module. When I try to run 'modprobe ppp_mppe' it hangs indefinitely. What would cause this hang? Any ideas how I can troubleshoot this further? Thanks for the help! UPDATE: I am still having the problem, however I have found some more information. When the first user tries to connect to pptp, the process list shows modprobe sha1 running, and one instance of modprobe ppp_mppe for each connection attempt. If I killall modprobe at this point the next connection attempt works, and everything is fine until the next reboot. I'm planning to do a clean install at some point in the future but I'd really like to get to the real cause of this.

  Read the article

• Corrupted NTFS Drive showing multiple unallocated partitions

  - by volting

  My external hdd with a single NTFS partition was accidentaly plugged out (kids!)... and is now corrupted. Iv tried running ntfsfix - with no luck - output below.. When I look at the disk under disk management in Windows 7 it shows up as having 5 partitions 2 of which are unallocated - none have drive letters and it is not possible to set any (that option and most others are greyed out) - so I can't run chkdsk /f Iv tried using Minitool partition wizard which was mentioned as a solution to another similar question here. It showed the whole drive as one partition, but as unallocated, and the option -- "Check File System" was greyout. Is there anything else I could try ? Output of fdisk -l Disk /dev/sdb: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytest I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x69205244 This doesn't look like a partition table Probably you selected the wrong device. Device Boot Start End Blocks Id System /dev/sdb1 ? 218129509 1920119918 850995205 72 Unknown /dev/sdb2 ? 729050177 1273024900 271987362 74 Unknown /dev/sdb3 ? 168653938 168653938 0 65 Novell Netware 386 /dev/sdb4 2692939776 2692991410 25817+ 0 Empty Partition table entries are not in disk order Output of ntfsfix me@vaio:/dev$ sudo ntfsfix /dev/sdb Mounting volume... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Attempting to correct errors... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Failed to startup volume: Input/output error Checking for self-located MFT segment... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument OK ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error Volume is corrupt. You should run chkdsk. Options available with MiniTool: Related questions: How to fix a damaged/corrupted NTFS filesystem/partition without losing the data on it? Repair corrupted NTFS File System

  Read the article

• VirtualBox management interface unreliability

  - by Arlen Cuss

  I'm using VirtualBox 3.2.8_OSE with 20 VMs running, and everything's going fine. I find that if I hammer the VBoxManage interface, all sorts of interesting things happen, usually necessitating either a restart of the VM in question, or of all VMs. For instance, if I use VBoxManage guestcontrol execute to run processes, after a few hours of using it maybe once or twice a minute on any given VM, it'll mysteriously start reporting VERR_NOT_IMPLEMENTED and refusing to do anything—sometimes trying to restart /usr/sbin/VBoxService on the VM itself will get it back in working order, but often it won't, and in the meantime, no data can be collected using VBoxManage. Such data includes the VM's IP, so if I hadn't recorded it earlier, I'm usually in trouble and have no option but to portscan the network for it, or kill the VM's process on the host manually and restart it. This one I haven't narrowed down yet, but it seems that even using VBoxManage guestproperty get (to retrieve a machine's IP) frequently and rapidly is enough to cause all VMs' management interfaces to die. The processes are still running fine, but VBoxManage reports them all as "powered off". In the meantime, another process somewhere in the system seems to have decided that their being powered off means they need to be powered on again, and suddenly I have 2x the number of VBoxHeadless processes running than I used to. Has anyone else seen behaviour like this? Is there any workaround? This is a serious impediment to my work, as I've had to resort to a lot of (hacky) caching of data and rate-limiting how often I call VBoxManage, just in case I accidentally bring 20 VMs to their knees.

  Read the article

• Hadoop initscript askes password

  - by Ramesh

  I have installed hadoop on my ubuntu 12.04 single node .I am trying to execute an init script to make the hadoop run on start up but it asks password every time i execute. #!/bin/sh ### BEGIN INIT INFO # Provides: hadoop services # Required-Start: $network # Required-Stop: $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Description: Hadoop services # Short-Description: Enable Hadoop services including hdfs ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HADOOP_BIN=/home/naveen/softwares/hadoop-1.0.3/bin NAME=hadoop DESC=hadoop USER=naveen ROTATE_SUFFIX= test -x $HADOOP_BIN || exit 0 RETVAL=0 set -e cd / start_hadoop () { set +e su $USER -s /bin/sh -c $HADOOP_BIN/start-all.sh > /var/log/hadoop/startup_log case "$?" in 0) echo SUCCESS RETVAL=0 ;; 1) echo TIMEOUT - check /var/log/hadoop/startup_log RETVAL=1 ;; *) echo FAILED - check /var/log/hadoop/startup_log RETVAL=1 ;; esac set -e } stop_hadoop () { set +e if [ $RETVAL = 0 ] ; then su $USER -s /bin/sh -c $HADOOP_BIN/stop-all.sh > /var/log/hadoop/shutdown_log RETVAL=$? if [ $RETVAL != 0 ] ; then echo FAILED - check /var/log/hadoop/shutdown_log fi else echo No nodes running RETVAL=0 fi set -e } restart_hadoop() { stop_hadoop start_hadoop } case "$1" in start) echo -n "Starting $DESC: " start_hadoop echo "$NAME." ;; stop) echo -n "Stopping $DESC: " stop_hadoop echo "$NAME." ;; force-reload|restart) echo -n "Restarting $DESC: " restart_hadoop echo "$NAME." ;; *) echo "Usage: $0 {start|stop|restart|force-reload}" >&2 RETVAL=1 ;; esac exit $RETVAL Please tell me how to run hadoop without entering password.

  Read the article

• best practices for setting up a new windows 2008 R2 server with ec2 AWS

  - by Alex

  Can someone comment what they would add to the following list of SOP in terms of best practices? This is being set up on AWS, and then after further testing, back in our datacenter. Standard Operation Procedure (SOP): Installation Part: 2 - Installation of Software Components in Windows 2008 R2 (Updated). Step: 1 Logon to the host through Remote Desktop. Strp: 2 Open Server Manager - Server Roles - Install Web Server IIS 7.5 with compatible of IIS 6 features and Management compatibility mode. Step: 3 Open IE/Mozilla to Download the below listed software's and save all installation files to folder called "AWS Server Install Files" for future reference.. Net Framework 2.0 (Download that from internet) Crystal reports for .Net Framework 2.0 (x64) (Download that from internet) SQL Server 2005 (AWS Image) Step: 4 Once all software's saved on local drive, then Install it one by one. Step: 5 Navigate to Desktop folder to install the below listed softwares. Microsoft Asp.net 2.0 AjaxExtention 1.0 (placed on Desktop \Softwares) WebEx recorder. (placed on Desktop \Softwares) Winrar(placed on Desktop \Softwares) Step: 6 Make sure all the software are working fine. Step: 7 Inspect the server once entirely. Step: 8 Logoff & Stop the Instance.

  Read the article

• Starting multiple Chrome full screen instances on multiple monitors from (batch) script

  - by Bob Groeneveld

  My goal is to show different web content full screen on multiple monitors automatically after booting from a single computer. The browser I would like to use is Chrome. If Chrome does not support this and Firefox does that would be fine. The OS I would prefer is Windows, if it turns out that Linux is possible that would be fine. On Windows it is possible to set the position of the Chrome browser window (--window-position=) and make Chrome start in full screen mode (--kiosk). Using these options combined you can start Chrome full screen on any of the desktops/screens that you have connected to your computer. I have managed to get this working. However, if I then try to do the same thing a second time to have Chrome full screen on a second screen the second Chrome window will open over the first window, no matter the coordinates I use for the --window-position parameter. I have tried using Chrome profiles and copying the Chrome directory and starting the second chrome.exe. All these things result in the same behaviour.

  Read the article

• Having trouble keeping a 1GB RAM Centos server running

  - by Josh

  This is my first time configuring a VPS server and I'm having a few issues. We're running Wordpress on a 1GB Centos server configured per the internet (online research). No custom queries or anything crazy but closing in on 8K posts. At arbitrary intervals, the server just goes down. From the client side, it just says "Loading..." and will spin more or less indefinitely. On the server side, the shell will lock completely. We have to do a hard reboot from the control panel and then everything is fine. Watching "top" I see it hovering between 35 - 55% memory usage generally and occasional spikes up to around 80%. When I saw it go down, there were about 30 - 40 Apache processes showing which pushed memory over the edge. "error_log" tells me that maxclients was reached right before each reboot instance. I've tried tinkering with that but to no avail. I think we'll probably need to bump the server up to the next RAM level but with ~120K pageviews per month, it seems like that's a bit overkill since it was running fairly well on a shared server before. Any ideas? httpd.conf and my.cnf values to add? I'll update this with the current ones if that helps. Thanks in advance! This has been a fun and important learning experience but, overall, quite frustrating! Edit: quick top snapshot: top - 15:18:15 up 2 days, 13:04, 1 user, load average: 0.56, 0.44, 0.38 Tasks: 85 total, 2 running, 83 sleeping, 0 stopped, 0 zombie Cpu(s): 6.7%us, 3.5%sy, 0.0%ni, 89.6%id, 0.0%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 2051088k total, 736708k used, 1314380k free, 199576k buffers Swap: 4194300k total, 0k used, 4194300k free, 287688k cached

  Read the article

• Postgres pgpass windows - not working

  - by Scott

  DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

  Read the article

• How can I remotely display images on my computer?

  - by Jakob

  What I Have: A laptop booted with Ubuntu and a stationary computer dual-booted with Ubuntu and Vista, both connected through a wireless ad-hoc network. What I Want: I want a way to display images in fullscreen on my stationary, using my laptop as a "remote control". I want to be able to choose another picture at any time and have my stationary computer remain in fullscreen mode at all times. Preferably, I should also be able to display just an empty (black) screen. How can I arrange for this? What I Have Tried: I have tried simply SSH:ing into my stationary computer and opening the image files using an image viewer, but all of the ones that I have tried (Eye of Gnome, Mirage, Gwenview, and others) open a new window for every new image. I don't know how to force them into using a single instance. I have tried using the VLC remote control command line interface, but apart from seeming somewhat unreliable (exiting with segmentation faults at one point), it also displays some images with a green border and forces me to pause playback in order for the image to remain on screen. Bonus Question: In my final setup, I also need to play music through my stationary computer's speaker and have the ability to switch to another track at any point, like with the images. Preferably, I would like to control the images and the audio through the same interface. How can I best achieve this?

  Read the article

• Performance tweaks and upgrades for VMWare Server 2

  - by sjohnston

  Our software department has a server running VMWare Server 2. We typically have 8-10 VMs running as test environments (Win XP and Server 08) for various versions of our software, and one VM that is used as a build server (Win XP). The host is running Server 2003 R2. It has 32GB RAM, 8 core Xeon 3.16GHz CPU, one disk for host OS and two raid disks for VMs. The majority of the time, this setup behaves very well and there are no complaints. Other times, the VMs can be very laggy. This is sometimes, but not always, correlated to heavy load on the build server. I'm a software developer, not an IT pro, but it seems to me that this machine should be beefy enough to handle this many VMs. Is this occasional performance hit likely just because we're hitting the limits of the hardware, or should I be looking for another culprit? From what I've read, I'm guessing if there's a bottleneck, it's probably disk I/O with all these VMs running off two disks (especially the build server). Would spreading the VMs over more disks, and/or switching to SSDs give us a significant performance boost? Other things I've read may increase performance: single virtual processor per VM removing/disabling unused virtual hardware preallocated disk space not using snapshots setting a reserved memory limit on the host and disabling VM memory swapping Can anyone confirm or deny if any of these improve performance? What other good tweaks have I missed?

  Read the article

• Should an HA failover occur in this scenario?

  - by joeqwerty

  I'm running vSphere 5 in an HA cluster across two hosts (vsphereA and vsphereB). I have the HA cluster configured for host monitoring and datastore heartbeat monitoring with admission control disabled (hopefully I rightfully understand that datastore heartbeat monitoring prevents inadvertent and unwanted HA failovers due to management network isolation). Each host has a single connection to a dedicated iSCSI network and iSCSI target (no MPIO). All vmdk's for all VM's exist on the iSCSI datastore. As a test of HA I disconnected the iSCSI connection on vsphereB and was surprised to see that the running VM's on vsphereB continued to run on vsphereB. The powered off VM's were showing as inaccessible (which I expected due to the fact that they weren't running and the connection from vsphereB to the iSCSI target was severed) but the running VM's continued to run and continued to be "owned" by vsphereB. I expected to see an HA failover occur for those VM's and expected to see them "owned" by vsphereA after the HA failover (which didn't occur). I'm at a loss to understand why an HA failover didn't occur for those VM's. Am I misunderstanding in which cases an HA failover should occur?

  Read the article

• 7zip many files from different folders?

  - by mafutrct

  I would like to add a large number of files with different names from different folders to a single 7zip archive using 7za.exe. This should be simple, but it turned out to be a major pain. I created a file that contains the paths (7za -a @list.txt) but once there are too many (~100) files, it fails. Apparently the content of the argument file is pushed onto the command line buffer, which is far too small (the number of files to add is 1m). Splitting the process up by adding the files one by one is not feasible due to the way 7za works: When adding the next file, it creates a copy of the archive, adds the file to the copy and finally replaces the original. This is terribly slow once the archive gets to a couple 100MB in size. So far I am using a combination of the two approaches by adding a dozen files each time in a loop, but it is an unreliable hack and still very slow. Is there a better way to do it? I tried to use 7zip wrapper DLLs (I'm a C# programmer), but none of them worked reliably and I was repeatedly suggested to just use 7za instead.

  Read the article

• Managing rolling deployments in the cloud

  - by Josh Nankin

  Recently I've been experimenting with various cloud management tools like RightScale, Scalr, custom scripts for managing a variety of servers, each hosting several roles (app, db, load balancer, job queues, etc). The one thing I find lacking in most solutions is a way to do rolling deployments, i.e. running deployments sequentially across a number of servers with the same role. For instance, I dont want to build all of my webservers at the same time, as that will almost definitely result in some down time or 500s for my customers. I'd rather have one or two servers build at a time, while other servers are still available to handle requests. The other alternative is obviously to launch new servers that automatically update themselves on boot, but this isn't as cost effective, and most likely requires more time for the build to complete (it's faster to build on an existing server than to launch a new server and kill old ones). We've all heard of the big companies having the famous "push to build" button (companies like Twilio, Etsy, etc.) but it seems that they all have custom implementations of this. I'm not talking about a simple ssh-loop, clusterssh, or even an mcollective - I preferably want something with a nice simple interface that allows me to specify something like a RightScript or a Scalr script to run on a set of servers with a specific role, and it builds them sequentially. Does any one know of easy ways to get this done, or is this a candidate for a new open source project?

  Read the article

< Previous Page | 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050  | Next Page >