Search Results

Search found 2822 results on 113 pages for 'scheduled backups'.

Page 109/113 | < Previous Page | 105 106 107 108 109 110 111 112 113  | Next Page >

• What NAS setup for two-way syncing over the internet?

  - by Jamse

  I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker. Update I've been digging some more and it looks like QNAP's Remote Replication function is actually just Rsync, so only really suitable for one-way syncing. I've posted on their forum to double check, but I think that's the case. In which case, I think the focus of my question is now either: do any reasonably-priced NASs support bidirectional syncing over the internet?, or has anyone had any luck installing onto NASs for this purpose? (Also, updated question to clarify that I'm after two-way syncing.)

  Read the article

• parallel_for_each from amp.h – part 1

  - by Daniel Moth

  This posts assumes that you've read my other C++ AMP posts on index<N> and extent<N>, as well as about the restrict modifier. It also assumes you are familiar with C++ lambdas (if not, follow my links to C++ documentation). Basic structure and parameters Now we are ready for part 1 of the description of the new overload for the concurrency::parallel_for_each function. The basic new parallel_for_each method signature returns void and accepts two parameters: a grid<N> (think of it as an alias to extent) a restrict(direct3d) lambda, whose signature is such that it returns void and accepts an index of the same rank as the grid So it looks something like this (with generous returns for more palatable formatting) assuming we are dealing with a 2-dimensional space: // some_code_A parallel_for_each( g, // g is of type grid<2> [ ](index<2> idx) restrict(direct3d) { // kernel code } ); // some_code_B The parallel_for_each will execute the body of the lambda (which must have the restrict modifier), on the GPU. We also call the lambda body the "kernel". The kernel will be executed multiple times, once per scheduled GPU thread. The only difference in each execution is the value of the index object (aka as the GPU thread ID in this context) that gets passed to your kernel code. The number of GPU threads (and the values of each index) is determined by the grid object you pass, as described next. You know that grid is simply a wrapper on extent. In this context, one way to think about it is that the extent generates a number of index objects. So for the example above, if your grid was setup by some_code_A as follows: extent<2> e(2,3); grid<2> g(e); ...then given that: e.size()==6, e[0]==2, and e[1]=3 ...the six index<2> objects it generates (and hence the values that your lambda would receive) are:    (0,0) (1,0) (0,1) (1,1) (0,2) (1,2) So what the above means is that the lambda body with the algorithm that you wrote will get executed 6 times and the index<2> object you receive each time will have one of the values just listed above (of course, each one will only appear once, the order is indeterminate, and they are likely to call your code at the same exact time). Obviously, in real GPU programming, you'd typically be scheduling thousands if not millions of threads, not just 6. If you've been following along you should be thinking: "that is all fine and makes sense, but what can I do in the kernel since I passed nothing else meaningful to it, and it is not returning any values out to me?" Passing data in and out It is a good question, and in data parallel algorithms indeed you typically want to pass some data in, perform some operation, and then typically return some results out. The way you pass data into the kernel, is by capturing variables in the lambda (again, if you are not familiar with them, follow the links about C++ lambdas), and the way you use data after the kernel is done executing is simply by using those same variables. In the example above, the lambda was written in a fairly useless way with an empty capture list: [ ](index<2> idx) restrict(direct3d), where the empty square brackets means that no variables were captured. If instead I write it like this [&](index<2> idx) restrict(direct3d), then all variables in the some_code_A region are made available to the lambda by reference, but as soon as I try to use any of those variables in the lambda, I will receive a compiler error. This has to do with one of the direct3d restrictions, where only one type can be capture by reference: objects of the new concurrency::array class that I'll introduce in the next post (suffice for now to think of it as a container of data). If I write the lambda line like this [=](index<2> idx) restrict(direct3d), all variables in the some_code_A region are made available to the lambda by value. This works for some types (e.g. an integer), but not for all, as per the restrictions for direct3d. In particular, no useful data classes work except for one new type we introduce with C++ AMP: objects of the new concurrency::array_view class, that I'll introduce in the post after next. Also note that if you capture some variable by value, you could use it as input to your algorithm, but you wouldn’t be able to observe changes to it after the parallel_for_each call (e.g. in some_code_B region since it was passed by value) – the exception to this rule is the array_view since (as we'll see in a future post) it is a wrapper for data, not a container. Finally, for completeness, you can write your lambda, e.g. like this [av, &ar](index<2> idx) restrict(direct3d) where av is a variable of type array_view and ar is a variable of type array - the point being you can be very specific about what variables you capture and how. So it looks like from a large data perspective you can only capture array and array_view objects in the lambda (that is how you pass data to your kernel) and then use the many threads that call your code (each with a unique index) to perform some operation. You can also capture some limited types by value, as input only. When the last thread completes execution of your lambda, the data in the array_view or array are ready to be used in the some_code_B region. We'll talk more about all this in future posts… (a)synchronous Please note that the parallel_for_each executes as if synchronous to the calling code, but in reality, it is asynchronous. I.e. once the parallel_for_each call is made and the kernel has been passed to the runtime, the some_code_B region continues to execute immediately by the CPU thread, while in parallel the kernel is executed by the GPU threads. However, if you try to access the (array or array_view) data that you captured in the lambda in the some_code_B region, your code will block until the results become available. Hence the correct statement: the parallel_for_each is as-if synchronous in terms of visible side-effects, but asynchronous in reality.   That's all for now, we'll revisit the parallel_for_each description, once we introduce properly array and array_view – coming next. Comments about this post by Daniel Moth welcome at the original blog.

  Read the article

• Symantec Protection Suite and System Recovery 2011 Desktop Edition

  - by rihatum

  I am re-posting this as my previous question was being treated as if I am "Shopping or seeking Product Recommendations" even though I was NOT - BTW they have deleted my comments too which were not offensive in nature. anyway - I have re-phrased some parts of my question and I hope SF Admins "Do Not Modify / Edit" this one - will be most grateful for that. I have a lot of respect for the People who visit this SITE and help others ! Just To clarify : Just to go by SF rules - I am not seeking someone to Design this solution, I am simply seeking real world examples, experiences, technical expert opinions / suggestions, any tips or tricks they may have or any problems they may have faced while doing something similar above with these products. I am also not asking for Capacity Planning for Storage, We have done some research and I am seeking Expert Assurance / Suggestions. We (our company) are planning to deploy Symantec Endpoint Protection and Symantec Desktop Recovery 2011 Desktop Edition to our 3000 - 4000 workstations (Windows7 32 and 64) with a few 100s with Windows XP 32/64 Bit. I have read the implementation guide for SEP and have read tech-notes for Desktop Recovery 2011. Our team have planned to deploy this as follows : 1 x dedicated SQL 2008R2 for Symantec Endpoint Protection (Instead of using the Embedded Database) 1 x Dedicated SQL 2008R2 for Symantec Desktop Recovery 2011 (Instead of using the Embedded Database) 1 x Dedicated W2K8 R2 Box for the SEPM (Symantec Endpoint Protection Manager - Mgmt. APP) 1 x Dedicated W2K8 R2 Box for the Symantec Desktop Recovery 2011 Management Application Agent Deployment : As per Symantec Documentation for both of the above, an agent can be pushed via the Mgmt. Application (provided no firewalls are blocking ports required etc. - we have Windows firewall disabled already). Server Hardware : Per SQL Server : 16GB RAM + SAS DISKS + Dual XEON, RAID-10 for the SQL DB or I can always mount a LUN from our existing Hitachi or EMC SAN. SEPM Server : 16GB RAM + SAS DISKS + DUAL XEON System Recovery MGMT SERVER : 16GB RAM + SAS DISKS + DUAL XEON Above is the initial plan we have for 3000 - 4000 client workstation (Windows) Now my Questions :-) a) If we had these users distributed amongst two sites with AD DC / GC in each site, How would I restrict SEPM and Desktop Mgmt. solution to only check for users in their respective site ? b) At present all users are under one building but we are going to move some dept. to a new location (with dedicated connectivity), How would we control which SEPM / MGMT Server is responsible for which site ? c) We have netbackup in our environment backing up other servers, I am planning to protect these 4 (2 x SQL, 1 x SEPM, 1 x System Recovery Mgmt. Server) via netbackup or I can use System recovery 2011 server edition on all 4 of these boxes as well. (License is not an issue as we have the complete symantec portfolio included in our license). d) Now - Saving Desktop backups - What strategies have you implemented ? Any best practice recommendation for a large user base ? I was thinking to either mount a LUN from our Hitachi SAN on the Symantec Recovery Server itself or backup to the users hard drive locally and then copy it over to a network location ? Suggestions welcome :-) If you have anything to add / correct - that will be really helpful before diving into the actual implementation phase. Will be most grateful with your suggestions, recommendations and corrections with above - Many Thanks !

  Read the article

• Windows 7 inbuilt and 3rd party (de)fragmentation related queries

  - by Karan

  I have a pretty good idea of how files end up getting fragmented. That said, I just copied ~3,200 files of varying sizes (from a few KB to ~20GB) from an external USB HDD to an internal, freshly formatted (under Windows 7 x64), NTFS, 2TB, 5400RPM, WD, SATA, non-system (i.e. secondary) drive, filling it up 57%. Since it should have been very much possible for each file to have been stored in one contiguous block, I expected the drive to be fragmented not more than 1-2% at most after this rather lengthy exercise (unfortunately this older machine doesn't support USB 3.0). Windows 7's inbuilt defrag utility told me after a quick analysis that the drive was fragmented only 1% or so, which dovetailed neatly with my expectations. However, just out of curiosity I downloaded and ran the latest portable x64 version of Piriform's Defraggler, and was shocked to see the drive being reported as being ~85% fragmented! The portable version of Auslogics Disk Defrag also agreed with Defraggler, and both clearly expected to grind away for ~10 hours to completely defragment the drive. 1) How in blazes could the inbuilt and 3rd party defrag utils disagree so badly? I mean, 10-20% variance is probably understandable, but 1% and 85% are miles apart! This Engineering Windows 7 blog post states: In Windows XP, any file that is split into more than one piece is considered fragmented. Not so in Windows Vista if the fragments are large enough – the defragmentation algorithm was changed (from Windows XP) to ignore pieces of a file that are larger than 64MB. As a result, defrag in XP and defrag in Vista will report different amounts of fragmentation on a volume. ... [Please read the entire post so the quote is not taken out of context.] Could it simply be that the 3rd party defrag utils ignore this post-XP change and continue to use analysis algos similar to those XP used? 2) Assuming that the 3rd party utils aren't lying about the real extent of fragmentation (which Windows is downplaying post-XP), how could the files have even got fragmented so badly given they were just copied over afresh to an empty drive? 3) If vastly differing analysis algos explain the yawning gap, which do I believe? I'm no defrag fanatic for sure, but 85% is enough to make me seriously consider spending 10 hours defragging this drive. On the other hand, 1% reported by Windows' own defragger clearly implies that there is no cause for concern and defragging would actually have negative consequences (as per the post). Is Windows' assumption valid and should I just let it be, or will there be any noticeable performance gains after running one of the 3rd party utils for 10 hours straight? 4) I see that out of the box Windows 7 defrag is scheduled to run weekly. Does anyone know whether it defrags every single time, or only if its analysis reveals a fragmentation percentage over a set threshold? If the latter, what is this threshold and can it be changed, maybe via a Registry edit? Thanks for reading through (my first query on this wonderful site!) and for any helpful replies. Also, if you're answering question #3, please keep in mind that any speed increases post defragging with 3rd party utils vis-à-vis Windows' inbuilt program should not include pre-Vista (preferably pre-Win7) examples. Further, examples of programs that made your system boot faster won't help in this case, since this is a non-system drive (although one that'll still be used daily).

  Read the article

• Organization &amp; Architecture UNISA Studies &ndash; Chap 4

  - by MarkPearl

  Learning Outcomes Explain the characteristics of memory systems Describe the memory hierarchy Discuss cache memory principles Discuss issues relevant to cache design Describe the cache organization of the Pentium Computer Memory Systems There are key characteristics of memory… Location – internal or external Capacity – expressed in terms of bytes Unit of Transfer – the number of bits read out of or written into memory at a time Access Method – sequential, direct, random or associative From a users perspective the two most important characteristics of memory are… Capacity Performance – access time, memory cycle time, transfer rate The trade off for memory happens along three axis… Faster access time, greater cost per bit Greater capacity, smaller cost per bit Greater capacity, slower access time This leads to people using a tiered approach in their use of memory   As one goes down the hierarchy, the following occurs… Decreasing cost per bit Increasing capacity Increasing access time Decreasing frequency of access of the memory by the processor The use of two levels of memory to reduce average access time works in principle, but only if conditions 1 to 4 apply. A variety of technologies exist that allow us to accomplish this. Thus it is possible to organize data across the hierarchy such that the percentage of accesses to each successively lower level is substantially less than that of the level above. A portion of main memory can be used as a buffer to hold data temporarily that is to be read out to disk. This is sometimes referred to as a disk cache and improves performance in two ways… Disk writes are clustered. Instead of many small transfers of data, we have a few large transfers of data. This improves disk performance and minimizes processor involvement. Some data designed for write-out may be referenced by a program before the next dump to disk. In that case the data is retrieved rapidly from the software cache rather than slowly from disk. Cache Memory Principles Cache memory is substantially faster than main memory. A caching system works as follows.. When a processor attempts to read a word of memory, a check is made to see if this in in cache memory… If it is, the data is supplied, If it is not in the cache, a block of main memory, consisting of a fixed number of words is loaded to the cache. Because of the phenomenon of locality of references, when a block of data is fetched into the cache, it is likely that there will be future references to that same memory location or to other words in the block. Elements of Cache Design While there are a large number of cache implementations, there are a few basic design elements that serve to classify and differentiate cache architectures… Cache Addresses Cache Size Mapping Function Replacement Algorithm Write Policy Line Size Number of Caches Cache Addresses Almost all non-embedded processors support virtual memory. Virtual memory in essence allows a program to address memory from a logical point of view without needing to worry about the amount of physical memory available. When virtual addresses are used the designer may choose to place the cache between the MMU (memory management unit) and the processor or between the MMU and main memory. The disadvantage of virtual memory is that most virtual memory systems supply each application with the same virtual memory address space (each application sees virtual memory starting at memory address 0), which means the cache memory must be completely flushed with each application context switch or extra bits must be added to each line of the cache to identify which virtual address space the address refers to. Cache Size We would like the size of the cache to be small enough so that the overall average cost per bit is close to that of main memory alone and large enough so that the overall average access time is close to that of the cache alone. Also, larger caches are slightly slower than smaller ones. Mapping Function Because there are fewer cache lines than main memory blocks, an algorithm is needed for mapping main memory blocks into cache lines. The choice of mapping function dictates how the cache is organized. Three techniques can be used… Direct – simplest technique, maps each block of main memory into only one possible cache line Associative – Each main memory block to be loaded into any line of the cache Set Associative – exhibits the strengths of both the direct and associative approaches while reducing their disadvantages For detailed explanations of each approach – read the text book (page 148 – 154) Replacement Algorithm For associative and set associating mapping a replacement algorithm is needed to determine which of the existing blocks in the cache must be replaced by a new block. There are four common approaches… LRU (Least recently used) FIFO (First in first out) LFU (Least frequently used) Random selection Write Policy When a block resident in the cache is to be replaced, there are two cases to consider If no writes to that block have happened in the cache – discard it If a write has occurred, a process needs to be initiated where the changes in the cache are propagated back to the main memory. There are several approaches to achieve this including… Write Through – all writes to the cache are done to the main memory as well at the point of the change Write Back – when a block is replaced, all dirty bits are written back to main memory The problem is complicated when we have multiple caches, there are techniques to accommodate for this but I have not summarized them. Line Size When a block of data is retrieved and placed in the cache, not only the desired word but also some number of adjacent words are retrieved. As the block size increases from very small to larger sizes, the hit ratio will at first increase because of the principle of locality, which states that the data in the vicinity of a referenced word are likely to be referenced in the near future. As the block size increases, more useful data are brought into cache. The hit ratio will begin to decrease as the block becomes even bigger and the probability of using the newly fetched information becomes less than the probability of using the newly fetched information that has to be replaced. Two specific effects come into play… Larger blocks reduce the number of blocks that fit into a cache. Because each block fetch overwrites older cache contents, a small number of blocks results in data being overwritten shortly after they are fetched. As a block becomes larger, each additional word is farther from the requested word and therefore less likely to be needed in the near future. The relationship between block size and hit ratio is complex, and no set approach is judged to be the best in all circumstances.   Pentium 4 and ARM cache organizations The processor core consists of four major components: Fetch/decode unit – fetches program instruction in order from the L2 cache, decodes these into a series of micro-operations, and stores the results in the L2 instruction cache Out-of-order execution logic – Schedules execution of the micro-operations subject to data dependencies and resource availability – thus micro-operations may be scheduled for execution in a different order than they were fetched from the instruction stream. As time permits, this unit schedules speculative execution of micro-operations that may be required in the future Execution units – These units execute micro-operations, fetching the required data from the L1 data cache and temporarily storing results in registers Memory subsystem – This unit includes the L2 and L3 caches and the system bus, which is used to access main memory when the L1 and L2 caches have a cache miss and to access the system I/O resources

  Read the article

• What NAS setup for syncing over the internet?

  - by Jamse

  I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker.

  Read the article

• IPv6: Should I have private addresses?

  - by AlReece45

  Right now, we have a rack of servers. Every server right now has at least 2 IP addresses, one for the public interface, another for the private. The servers that have SSL websites on them have more IP addresses. We also have virtual servers, that are configured similarly. Private Network The private range is currently just used for backups and monitoring. Its a gigabit port, the interface usage does not usually get very high. There are other technologies we're considering using that would use this port: iSCSI (implementations usually recommends dedicating an interface to it, which would be yet another IP network), VPN to get access to the private range (something I'd rather avoid) dedicated database servers LDAP centralized configuration (like puppet) centralized logging We don't have any private addresses in our DNS records (only public addresses). For our servers to utilize the correct IP address for the right interface (and not hard code the IP address) probably requires setting up a private DNS server (So now we add 2 different dns entries to 2 different systems). Public Network Our public range has a variety of services include web, email, and ftp. There is a hardware firewall between our network and the "public" network. We have (relatively secure) method to instruct the firewall to open and close administrative access (web interfaces, ssh, etc) for our current IP address. With either solution discussed, the host-based firewalls will be configured as well. The public network currently runs at a dedicated 20Mbps link. There are a couple of legacy servers with fast-ethernet ports, but they are scheduled for decommissioning. All of the other production boxes have at least 2 Gigabit Ethernet ports. The more traffic-heavy servers have 4-6 available (none is using more than the 2 Gigabit ports right now). IPv6 I want to get an IPv6 prefix from our ISP. So at least every "server" has at least one IPv6 interface. We'll still need to keep the IPv4 addressees up and available for legacy clients (web servers and email at the very least). We have two IP networks right now. Adding the public IPv6 address would make it three. Just use IPv6? I'm thinking about just dumping the private IPv4 range and using the IPv6 range as the primary means of all communications. If an interface starts reaching its capacity, utilize the newly free interfaces to create a trunk. It has the advantage that if either the public or private traffic needs to exceed 1Gbps. The traffic for each interface is already analyzed on a regular basis to predict future bandwidth use. In the rare instances where bandwidth unexpected peaks: utilize QoS to ensure traffic (like our limited SSH access) is prioritized correctly so the problem can be corrected (if possible, our WAN is the bottleneck right now). It also has the advantage of not needing to make an entry for every private address. We may have private DNS (or just LDAP), but it'll be much more limited in scope with less entries to duplicate. Summary I'm trying to make this network as "simple" as possible. At the same time, I want to make sure its reliable, upgradeable, scalable, and (eventually) redundant. Having one IPv6 network, and a legacy IPv4 network seems to be the best solution to me. Regarding using assigned IPv6 addresses for both networks, sharing the available bandwidth on one (more trunked if needed): Are there any technical disadvantages (limitations, buffers, scalability)? Are there any other security considerations (asides from firewalls mentioned above) to consider? Are there regulations or other security requirements (like PCI-DSS) that this doesn't meet? Is there typical software for setting up a Linux network that doesn't have IPv6 support yet? (logging, ldap, puppet) Some other thing I didn't consider?

  Read the article

• My 2009 MacBook Logic board failed - options to proceed and how difficult?

  - by user181061

  Scannerz just gave my MacBook logic board a big fat F! I upgraded from Snow Leopard to Mountain Lion about 3 weeks ago. The system was running short of memory so I upgraded it. The system was running fine for about 2 weeks. Yesterday the thing started acting erratic. A lot of spinning beach balls, delays, and then some errors saying files couldn't be read to or from the drive. I figured the drive was going because the system is over 3 years old. I ran Scannerz on it and it indicated a lot of errors and irregularities. I rescanned it in cursory mode, and none of them were repeatable, just showing up all over the place in different regions of the scan. I went through the docs and they implied either an I/O cable was bad, a connection was damaged, or the logic board was bad. I tossed on my backup of Snow Leopard that I cloned from the original hard drive because I figured Mountain Lion was to blame and booted from the USB drive with the clone on it. It wasn't. I performed scans on every single port, and errors and irregularities that couldn't be repeated were showing up on every single one of them. I then, for kicks, put a CD into the CD player. Scannerz doesn't test optical drives but I figured surely that will work. No it won't. More spinning beach balls and messages telling me it can't be read. It was working fine 3 days ago. I know a lot of people don't like MacBook's, but mine's been great, at least until now. It was working great even with Mountain Lion after the upgrade. The system is a mid-2009 MacBook. In my opinion, it's a complete waste to toss this system. The display is too good, the keyboard works great, and it still looks good, plus this type of MacBook still uses the FireWire 400 port and I use that for Time Machine backups. I've tried reseating the RAM, it didn't do anything. I shut the system down and put in the old RAM, booted to Snow Leopard, and the problems persist. Here are my questions: The Scannerz documentation somewhere said something about the Airport card not being seated properly, but when I go to iFixit, it's apparent, at least I think it's apparent, that this isn't a slot type Airport card that the user can easily install or remove. If the cables or connections to the Airport card are bad, could they be causing this problem. How about any other connections that can be intermittent, failing or erratic? Any type of resets that I could possibly do to get rid of this? For any of those that have replaced a logic board on a MacBook, if this really is the culprit, are there any "gotcha's" I need to be aware of? As an FYI, I replaced the hard drive on an old iBook @500MHz that I had a long time ago, and I replaced the drive on a 1.33GHz PowerBook about 6 years ago. You have to be careful, but using some of the info on web sites like iFixit it's not that hard. Time consuming, but not that hard. The Intel based MacBook's to me look like they're easier to service than either of those. I'm thinking about getting a unit off of eBay that matches mine but has something else wrong with it, like a busted display. I REFUSE to buy a new system. A guy at my office has a 2007 Mac Pro and he can't upgrade to Mountain Lion because his system is "obsoleted." That's ridiculous. If you pay nearly $7,500 for a system it shouldn't be trash just because Apple decides they don't have enough money (sorry for the soap box, but it's true, IMO!) Any input is appreciated.

  Read the article

• Maintenance plans love story

  - by Maria Zakourdaev

  There are about 200 QA and DEV SQL Servers out there.  There is a maintenance plan on many of them that performs a backup of all databases and removes the backup history files. First of all, I must admit that I’m no big fan of maintenance plans in particular or the SSIS packages in general.  In this specific case, if I ever need to change anything in the way backup is performed, such as the compression feature or perform some other change, I have to open each plan one by one. This is quite a pain. Therefore, I have decided to replace the maintenance plans with a stored procedure that will perform exactly the same thing.  Having such a procedure will allow me to open multiple server connections and just execute an ALTER PROCEDURE whenever I need to change anything in it. There is nothing like good ole T-SQL. The first challenge was to remove the unneeded maintenance plans. Of course, I didn’t want to do it server by server.  I found the procedure msdb.dbo.sp_maintplan_delete_plan, but it only has a parameter for the maintenance plan id and it has no other parameters, like plan name, which would have been much more useful. Now I needed to find the table that holds all maintenance plans on the server. You would think that it would be msdb.dbo.sysdbmaintplans but, unfortunately, regardless of the number of maintenance plans on the instance, it contains just one row.    After a while I found another table: msdb.dbo.sysmaintplan_subplans. It contains the plan id that I was looking for, in the plan_id column and well as the agent’s job id which is executing the plan’s package: That was all I needed and the rest turned out to be quite easy.  Here is a script that can be executed against hundreds of servers from a multi-server query window to drop the specific maintenance plans. DECLARE @PlanID uniqueidentifier   SELECT @PlanID = plan_id FROM msdb.dbo.sysmaintplan_subplans Where name like ‘BackupPlan%’   EXECUTE msdb.dbo.sp_maintplan_delete_plan @plan_id=@PlanID   The second step was to create a procedure that will perform  all of the old maintenance plan tasks: create a folder for each database, backup all databases on the server and clean up the old files. The script is below. Enjoy.   ALTER PROCEDURE BackupAllDatabases                                   @PrintMode BIT = 1 AS BEGIN          DECLARE @BackupLocation VARCHAR(500)        DECLARE @PurgeAferDays INT        DECLARE @PurgingDate VARCHAR(30)        DECLARE @SQLCmd  VARCHAR(MAX)        DECLARE @FileName  VARCHAR(100)               SET @PurgeAferDays = -14        SET @BackupLocation = '\\central_storage_servername\BACKUPS\'+@@servername               SET @PurgingDate = CONVERT(VARCHAR(19), DATEADD (dd,@PurgeAferDays,GETDATE()),126)               SET @FileName = '?_full_'+                      + REPLACE(CONVERT(VARCHAR(19), GETDATE(),126),':','-')                      +'.bak';          SET @SQLCmd = '               IF ''?'' <> ''tempdb'' BEGIN                      EXECUTE master.dbo.xp_create_subdir N'''+@BackupLocation+'\?\'' ;                        BACKUP DATABASE ? TO  DISK = N'''+@BackupLocation+'\?\'+@FileName+'''                      WITH NOFORMAT, NOINIT,  SKIP, REWIND, NOUNLOAD, COMPRESSION,  STATS = 10 ;                        EXECUTE master.dbo.xp_delete_file 0,N'''+@BackupLocation+'\?\'',N''bak'',N'''+@PurgingDate+''',1;               END'          IF @PrintMode = 1 BEGIN               PRINT @SQLCmd        END               EXEC sp_MSforeachdb @SQLCmd        END

  Read the article

• Network update solutions for a company of ~20 (5 local, 15 remote)?

  - by Margaret

  Hi all This is probably going to be a bit up in the air, because we're still in the "reaching towards solutions" phase, but I figured I'd see what you guys had to say. Plus I honestly know very little about systems and what is good and bad pratice. My organisation has always more or less worked on the concept of local machines; since it primarily employed contractors who were working from home, each of those people was largely responsible for their own machine and backup procedures and the like. We're now expanding, though we're still reasonably small (we're up to about 20 staff members). Most people still work remotely, but we have a central office where about five people are working. But we're getting large enough that we're starting to think it would be a good idea to have a central file server, and things like that - if someone gets hit by a bus, we want someone else to know where to look for the files to continue their work. A lot of the people who work for us remotely work on projects for other companies as well, so I don't want to force them to log in to our server whenever they're on a network. But I do want to make connection to be as painless as possible to do so, to improve utilisation. The other thing is that we're getting more people who would like to remote into the office server and do their work there. Our current remote connection application is an SSH install that allows people access to the network; the problem is, it's a black box to me, and I've never understood how to even connect to it (despite supposedly being de facto sysadmin). Thus far I've been able to bounce questions about how to get it working to the guy who does know it well, but he's leaving the company soon. So we probably need a solution for this that I actually understand. We were knocking around the idea of implementing a VPN with some form of remote desktop, and someone mentioned that this was largely a matter of purchasing a router capable of it; I'm not sure of the truth of that statement. This is what we have in the office: Two shiny new i7 servers, each running Windows Server 2008. Precise eventual layout is still being debated, a little, but the current suggestion is that one is primary database crunching, while the other is a warm backup of the databases, along with running Reporting Services. They currently have SQL Server 2008 installed on them, which is being connected to via the 'sa' account. We're hoping to make each person use their own account (preferably one tied to the 'central' password we set up, so we can use Windows Authentication). An older server, running XP Pro, that we are currently using as a test bed for a project that requires access to older versions of software. This machine is also being used to take backups, but I'm thinking of moving that functionality elsewhere. A spare desktop from a guy who left the company (XP Pro). We're thinking of bumping up the hard disk space and using it as the magical file server that's going to solve one particular everything. Assorted desktops, laptops, etc, at least one for each person in the office (mix of Win XP and Win 7; occasionally a person who normally works remotely might drop in to the office and bring a laptop bearing Vista, but it's pretty rare). All are set up as local user accounts at the moment; I don't know if it's the best arrangement. Purchasing more hardware is not a big problem, but we figure we might as well make use of what we've got first. Is Active Directory a big magic wand that's going to solve all the world's problems? Is there some other arrangement we should be looking to instead?

  Read the article

• Mass targeted malware installed - g00glestatic.com [closed]

  - by Silver89

  Possible Duplicate: My server’s been hacked EMERGENCY I run a webserver which over the last few days seems to have become infected with malware that tries to include content from "http://g00glestatic.com/s.js" It appears the attacker gained access to one of the user accounts (not root), made a few changes, added a few files and ran a few bash commands. These changes stuck out clearly to me because it is not a shared server and I am the only person with access through very secure passwords. The php/javascript code that was added .php files, this code was added: #9c282e# if(!$srvc_counter) { echo "<script type=\"text/javascript\" src=\"http://g00glestatic.com/s.js\"></script>"; $srvc_counter = true;} #/9c282e# .js files, this code was added: /*9c282e*/ var _f = document.createElement('iframe'),_r = 'setAttribute'; _f[_r]('src', 'http://g00glestatic.com/s.js'); _f.style.position = 'absolute';_f.style.width = '10px'; _f[_r]('frameborder', navigator.userAgent.indexOf('bf3f1f8686832c30d7c764265f8e7ce8') + 1); _f.style.left = '-5540px'; document.write('<div id=\'MIX_ADS\'></div>'); document.getElementById('MIX_ADS').appendChild(_f); /*/9c282e*/ The bash command taken from .bash_history (Some usernames/passwords have been subbed) su -c id $replacedPassword id; id; sudo id; replacedPassword id; cd /home/replacedUserId1; chmod +x .sess_28e2f1bc755ed3ca48b32fbcb55b91a7; ./.sess_28e2f1bc755ed3ca48b32fbcb55b91a7; rm /home/replacedUserId1/.sess_28e2f1bc755ed3ca48b32fbcb55b91a7; id; cd /home/replacedUserId1; chmod +x .sess_05ee5257fed0ac8e0f12096f4c3c0d20; ./.sess_05ee5257fed0ac8e0f12096f4c3c0d20; rm /home/replacedUserId1/.sess_05ee5257fed0ac8e0f12096f4c3c0d20; id; cd /home/replacedUserId1; chmod +x .sess_bfa542fc2578cce68eb373782c5689b9; ./.sess_bfa542fc2578cce68eb373782c5689b9; rm /home/replacedUserId1/.sess_bfa542fc2578cce68eb373782c5689b9; id; cd /home/replacedUserId1; chmod +x .sess_bfa542fc2578cce68eb373782c5689b9; ./.sess_bfa542fc2578cce68eb373782c5689b9; rm /home/replacedUserId1/.sess_bfa542fc2578cce68eb373782c5689b9; id; cd /home/replacedUserId1; chmod +x .sess_fb19dfb52ed4a3ae810cd4454ac6ef1e; ./.sess_fb19dfb52ed4a3ae810cd4454ac6ef1e; rm /home/replacedUserId1/.sess_fb19dfb52ed4a3ae810cd4454ac6ef1e; id; kill -9 $$;; kill -9 $$;; kill -9 $$; The above seems to move files added to the public_html to the level above? I also have all 4 of the files that were added: .sess_28e2f1bc755ed3ca48b32fbcb55b91a7 .sess_05ee5257fed0ac8e0f12096f4c3c0d20 .sess_bfa542fc2578cce68eb373782c5689b9 .sess_fb19dfb52ed4a3ae810cd4454ac6ef1e Of those four above files, three are none viewable in notepad++ and display null characters, whereas sess_fb19dfb52ed4a3ae810cd4454ac6ef1e consists of: #!/bin/sh export PATH=$PATH:/sbin:/usr/sbin:/usr/local/bin:/usr/local/sbin:/usr/bin; export LC_ALL=en_US.UTF-8 LC_COLLATE=en_US.UTF-8 LC_CTYPE=en_US.UTF-8 LANG=en_US.UTF-8 LANGUAGE=en_US.UTF-8 export TERM=linux echo -n "-> checking staprun: "; if which staprun 2>&1 | grep -q "no $1"; then flag=1 elif [ -z "`which $1 2>&1`" ]; then flag=1; fi if [ "$flag" = "1" ]; then echo "no staprun, exiting"; exit; else echo "found"; echo "-> trying to exploit... "; printf "install uprobes /bin/sh" > ololo.conf; MODPROBE_OPTIONS="-C ololo.conf" staprun -u ololo rm -f ololo.conf fi Other Noticeable Edits Any files that contain: ([.htaccess]|[index|header|footer].php|[*.js]) will have been modified and all system file and directory permissions will have been changed to: x--x--x My steps to remove this malware re uploaded original php/js files to revert any changes Changed all user passwords Modified hosts.allow to a static ip so that only I have access Removed the above 4 files and checked all modified file dates within that directory to check for any other recent modifications, none can be found Conclusion I'm hoping that as they did not have root access, any changes they wished to make higher up failed and they were only able to display an iframe on the site for a short amount of time? What else do I need to look for to check the malware infection has not spread? Second Conclusion This malware sinks too deep to 'clean', if you get infected I recommend a server nuke and rebuild from backups with increased security. Possibility It's possible that Filezilla ftp passwords were stolen through a trojan as they're unfortunately stored unencrypted. However Trend Micro Titanium has not found any. The settings box to disable passwords being saved has now been ticked, I also recommend that you take this action.

  Read the article

• Clients not updating with approved updates from WSUS

  - by Ross

  Hi All, I've been a bit behind in my windows XP updates recently, and I have about 18 or so I need to roll out to all our users, according to WSUS. I'm trying it on a couple of test PCs, and so far i've had no luck. On each one, one update would install (and need a reboot), and nothing else since. When I run wuauclt.exe /detectnow, I get this in the windowsupdate.log: 2009-10-29 17:27:10:624 1128 93c AU Triggering AU detection through DetectNow API 2009-10-29 17:27:10:624 1128 93c AU Triggering Online detection (non-interactive) 2009-10-29 17:27:10:624 1128 504 AU ############# 2009-10-29 17:27:10:624 1128 504 AU ## START ## AU: Search for updates 2009-10-29 17:27:10:624 1128 504 AU ######### 2009-10-29 17:27:10:624 1128 504 AU <<## SUBMITTED ## AU: Search for updates [CallId = {59353978-CBA7-4B0B-AFD3-515577D3C16B}] 2009-10-29 17:27:10:624 1128 a14 Agent ************* 2009-10-29 17:27:10:624 1128 a14 Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdates] 2009-10-29 17:27:10:624 1128 a14 Agent ********* 2009-10-29 17:27:10:624 1128 a14 Agent * Online = Yes; Ignore download priority = No 2009-10-29 17:27:10:624 1128 a14 Agent * Criteria = "IsHidden=0 and IsInstalled=0 and DeploymentAction='Installation' and IsAssigned=1 or IsHidden=0 and IsPresent=1 and DeploymentAction='Uninstallation' and IsAssigned=1 or IsHidden=0 and IsInstalled=1 and DeploymentAction='Installation' and IsAssigned=1 and RebootRequired=1 or IsHidden=0 and IsInstalled=0 and DeploymentAction='Uninstallation' and IsAssigned=1 and RebootRequired=1" 2009-10-29 17:27:10:624 1128 a14 Agent * ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} 2009-10-29 17:27:10:624 1128 a14 Misc Validating signature for C:\WINDOWS\SoftwareDistribution\SelfUpdate\Default\wuident.cab: 2009-10-29 17:27:10:655 1128 a14 Misc Microsoft signed: Yes 2009-10-29 17:27:10:702 1128 a14 Misc Validating signature for C:\WINDOWS\SoftwareDistribution\SelfUpdate\Default\wuident.cab: 2009-10-29 17:27:10:702 1128 a14 Misc Microsoft signed: Yes 2009-10-29 17:27:10:780 1128 a14 Misc Validating signature for C:\WINDOWS\SoftwareDistribution\SelfUpdate\Default\wsus3setup.cab: 2009-10-29 17:27:10:780 1128 a14 Misc Microsoft signed: Yes 2009-10-29 17:27:10:796 1128 a14 Setup *********** Setup: Checking whether self-update is required *********** 2009-10-29 17:27:10:796 1128 a14 Setup * Inf file: C:\WINDOWS\SoftwareDistribution\SelfUpdate\Default\wsus3setup.inf 2009-10-29 17:27:10:796 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\cdm.dll: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:796 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuapi.dll: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:796 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuapi.dll.mui: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:796 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuauclt.exe: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuaucpl.cpl: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuaucpl.cpl.mui: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuaueng.dll: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuaueng.dll.mui: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wucltui.dll: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wucltui.dll.mui: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wups.dll: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wups2.dll: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup Update NOT required for C:\WINDOWS\system32\wuweb.dll: target version = 7.1.6001.65, required version = 7.1.6001.65 2009-10-29 17:27:10:874 1128 a14 Setup * IsUpdateRequired = No 2009-10-29 17:27:17:468 1128 a14 PT +++++++++++ PT: Synchronizing server updates +++++++++++ 2009-10-29 17:27:17:468 1128 a14 PT + ServiceId = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7}, Server URL = hxxp://dublindc2/ClientWebService/client.asmx 2009-10-29 17:27:55:157 1128 a14 Agent * Found 0 updates and 46 categories in search; evaluated appl. rules of 478 out of 678 deployed entities 2009-10-29 17:27:55:173 1128 a14 Agent ********* 2009-10-29 17:27:55:173 1128 a14 Agent ** END ** Agent: Finding updates [CallerId = AutomaticUpdates] 2009-10-29 17:27:55:173 1128 a14 Agent ************* 2009-10-29 17:27:55:189 1128 f1c AU >>## RESUMED ## AU: Search for updates [CallId = {59353978-CBA7-4B0B-AFD3-515577D3C16B}] 2009-10-29 17:27:55:189 1128 f1c AU # 0 updates detected 2009-10-29 17:27:55:189 1128 f1c AU ######### 2009-10-29 17:27:55:189 1128 f1c AU ## END ## AU: Search for updates [CallId = {59353978-CBA7-4B0B-AFD3-515577D3C16B}] 2009-10-29 17:27:55:189 1128 f1c AU ############# 2009-10-29 17:27:55:189 1128 f1c AU AU setting next detection timeout to 2009-10-29 21:01:30 2009-10-29 17:27:55:189 1128 f1c AU Setting AU scheduled install time to 2009-10-30 13:00:00 2009-10-29 17:27:55:251 1128 a14 Report Uploading 2 events using cached cookie, reporting URL = hxxp://dublindc2/ReportingWebService/ReportingWebService.asmx 2009-10-29 17:27:55:267 1128 a14 Report Reporter successfully uploaded 2 events. 2009-10-29 17:28:00:173 1128 a14 Report REPORT EVENT: {BD891590-784B-4001-8116-D83962DAB749} 2009-10-29 17:27:55:173-0000 1 147 101 {00000000-0000-0000-0000-000000000000} 0 0 AutomaticUpdates Success Software Synchronization Windows Update Client successfully detected 0 updates. 2009-10-29 17:28:00:173 1128 a14 Report REPORT EVENT: {E578C377-5E09-4F4C-AB28-FE5131E2D6A7} 2009-10-29 17:27:55:173-0000 1 I've tried deleting everything in the C:\Windows\SoftwareDistribution, stopping the services, rebooting etc. Can anyone decipher the log to see where it's going wrong? Many thanks!

  Read the article

• MySQL InnoDB Corruption after power outage, possible to recover?

  - by Tim Hackett

  Hey Guys, I recently started trying to get Redmine up and running after a power outage that seems to have corrupted our InnoDB database in MySQL. Redmine had an extensive set of documentation that I would like to get even if redmine isn't able to run. The service fails on startup. I have tried inserting innodb_force_recovery = 4 per the documentation from the url in the error log. (also tried 1 thru 6 as I have backed up all directories after the corruption) I have verified through "mysqld-nt --print-defaults" that it is starting with the recovery option in the params. The machine is running Windows Server 2003 SP2, Xeon E5335 with 2GB RAM, MySQL is not mirrored to another machine, nor is the machine a mirror. I do not have any backups because the previous person did not set them up. Here is the error log: InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 100308 14:50:01 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 100308 14:50:02 InnoDB: Error: page 7 log sequence number 0 935521175 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 2 log sequence number 0 935517607 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 11 log sequence number 0 935517607 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 5 log sequence number 0 972973045 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 6 log sequence number 0 972984051 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 1577 log sequence number 0 972737368 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. InnoDB: Error: trying to access page number 4294965119 in space 0, InnoDB: space name .\ibdata1, InnoDB: which is outside the tablespace bounds. InnoDB: Byte offset 0, len 16384, i/o type 10. InnoDB: If you get this error at mysqld startup, please check that InnoDB: your my.cnf matches the ibdata files that you have in the InnoDB: MySQL server. 100308 14:50:02InnoDB: Assertion failure in thread 960 in file .\fil\fil0fil.c line 3959 InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: about forcing recovery. 100308 14:50:02 [ERROR] mysqld-nt: Got signal 11. Aborting! 100308 14:50:02 [ERROR] Aborting 100308 14:50:02 [Note] mysqld-nt: Shutdown complete

  Read the article

• Why might login failures cause SQL 2005 to dump and ditch?

  - by Byron Sommardahl

  Our SQL 2005 server began timing out and finally stopped responding on Oct 26th. The application logs showed a ton of 17883 events leading up to a reboot. After the reboot everything was fine but we were still scratching our heads. Fast forward 6 days... it happened again. Then again 2 days later. The last night. Today it has happened three times to far. The timeline is fairly predictable when it happens: Trans log backups. Login failure for "user2". Minidump Another minidump for the scheduler Repeated 17883 events. Server fails little by little until it won't accept any requests. Reboot is all that gets us going again (a band-aid) Interesting, though, is that the server box itself doesn't seem to have any problems. CPU usage is normal. Network connectivity is fine. We can remote in and look at logs. Management studio does eventually bog down, though. Today, for the first time, we tried stopping services instead of a reboot. All services stopped on their own except for the SQL Server service. We finally did an "end task" on that one and were able to bring everything back up. It worked fine for about 30 minutes until we started seeing timeouts and 17883's again. This time, probably because we didn't reboot all the way, we saw a bunch of 844 events mixed in with the 17883's. Our entire tech team here is scratching heads... some ideas we're kicking around: MS Cumulative Update hit around the same time as when we first had a problem. Since then, we've rolled it back. Maybe it didn't rollback all the way. The situation looks and feels like an unhandled "stack overflow" (no relation) in that it starts small and compounds over time. Problem with this is that there isn't significant CPU usage. At any rate, we're not ruling SQL 2005 bug out at all. Maybe we added one too many import processes and have reached our limit on this box. (hard to believe). Looking at SQLDUMP0151.log at the time of one of the crashes. There are some "login failures" and then there are two stack dumps. 1st a normal stack dump, 2nd for a scheduler dump. Here's a snippet: (sorry for the lack of line breaks) 2009-11-10 11:59:14.95 spid63 Using 'xpsqlbot.dll' version '2005.90.3042' to execute extended stored procedure 'xp_qv'. This is an informational message only; no user action is required. 2009-11-10 11:59:15.09 spid63 Using 'xplog70.dll' version '2005.90.3042' to execute extended stored procedure 'xp_msver'. This is an informational message only; no user action is required. 2009-11-10 12:02:33.24 Logon Error: 18456, Severity: 14, State: 16. 2009-11-10 12:02:33.24 Logon Login failed for user 'standard_user2'. [CLIENT: 50.36.172.101] 2009-11-10 12:08:21.12 Logon Error: 18456, Severity: 14, State: 16. 2009-11-10 12:08:21.12 Logon Login failed for user 'standard_user2'. [CLIENT: 50.36.172.101] 2009-11-10 12:13:49.38 Logon Error: 18456, Severity: 14, State: 16. 2009-11-10 12:13:49.38 Logon Login failed for user 'standard_user2'. [CLIENT: 50.36.172.101] 2009-11-10 12:15:16.88 Logon Error: 18456, Severity: 14, State: 16. 2009-11-10 12:15:16.88 Logon Login failed for user 'standard_user2'. [CLIENT: 50.36.172.101] 2009-11-10 12:18:24.41 Logon Error: 18456, Severity: 14, State: 16. 2009-11-10 12:18:24.41 Logon Login failed for user 'standard_user2'. [CLIENT: 50.36.172.101] 2009-11-10 12:18:38.88 spid111 Using 'dbghelp.dll' version '4.0.5' 2009-11-10 12:18:39.02 spid111 *Stack Dump being sent to C:\Program Files\Microsoft SQL Server\MSSQL.1\MSSQL\LOG\SQLDump0149.txt 2009-11-10 12:18:39.02 spid111 SqlDumpExceptionHandler: Process 111 generated fatal exception c0000005 EXCEPTION_ACCESS_VIOLATION. SQL Server is terminating this process. 2009-11-10 12:18:39.02 spid111 * ***************************************************************************** 2009-11-10 12:18:39.02 spid111 * 2009-11-10 12:18:39.02 spid111 * BEGIN STACK DUMP: 2009-11-10 12:18:39.02 spid111 * 11/10/09 12:18:39 spid 111 2009-11-10 12:18:39.02 spid111 * 2009-11-10 12:18:39.02 spid111 * 2009-11-10 12:18:39.02 spid111 * Exception Address = 0159D56F Module(sqlservr+0059D56F) 2009-11-10 12:18:39.02 spid111 * Exception Code = c0000005 EXCEPTION_ACCESS_VIOLATION 2009-11-10 12:18:39.02 spid111 * Access Violation occurred writing address 00000000 2009-11-10 12:18:39.02 spid111 * Input Buffer 138 bytes - 2009-11-10 12:18:39.02 spid111 * " N R S C _ P T A 22 00 4e 00 52 00 53 00 43 00 5f 00 50 00 54 00 41 00 2009-11-10 12:18:39.02 spid111 * C _ Q A . d b o . 43 00 5f 00 51 00 41 00 2e 00 64 00 62 00 6f 00 2e 00 2009-11-10 12:18:39.02 spid111 * U s p S e l N e x 55 00 73 00 70 00 53 00 65 00 6c 00 4e 00 65 00 78 00 2009-11-10 12:18:39.02 spid111 * t A c c o u n t 74 00 41 00 63 00 63 00 6f 00 75 00 6e 00 74 00 00 00 2009-11-10 12:18:39.02 spid111 * @ i n t F o r m I 0a 40 00 69 00 6e 00 74 00 46 00 6f 00 72 00 6d 00 49 2009-11-10 12:18:39.02 spid111 * D & 8 @ t x 00 44 00 00 26 04 04 38 00 00 00 09 40 00 74 00 78 00 2009-11-10 12:18:39.02 spid111 * t A l i a s § 74 00 41 00 6c 00 69 00 61 00 73 00 00 a7 0f 00 09 04 2009-11-10 12:18:39.02 spid111 * Ð GQE9732 d0 00 00 07 00 47 51 45 39 37 33 32 2009-11-10 12:18:39.02 spid111 * 2009-11-10 12:18:39.02 spid111 * 2009-11-10 12:18:39.02 spid111 * MODULE BASE END SIZE 2009-11-10 12:18:39.02 spid111 * sqlservr 01000000 02C09FFF 01c0a000 2009-11-10 12:18:39.02 spid111 * ntdll 7C800000 7C8C1FFF 000c2000 2009-11-10 12:18:39.02 spid111 * kernel32 77E40000 77F41FFF 00102000

  Read the article

• Mysql performance problem & Failed DIMM

  - by murdoch

  Hi I have a dedicated mysql database server which has been having some performance problems recently, under normal load the server will be running fine, then suddenly out of the blue the performance will fall off a cliff. The server isn't using the swap file and there is 12GB of RAM in the server, more than enough for its needs. After contacting my hosting comapnies support they have discovered that there is a failed 2GB DIMM in the server and have scheduled to replace it tomorow morning. My question is could a failed DIMM result in the performance problems I am seeing or is this just coincidence? My worry is that they will replace the ram tomorrow but the problems will persist and I will still be lost of explanations so I am just trying to think ahead. The reason I ask is that there is plenty of RAM in the server, more than required and simply missing 2GB should be a problem, so if this failed DIMM is causing these performance problems then the OS must be trying to access the failed DIMM and slowing down as a result. Does that sound like a credible explanation? This is what DELLs omreport program says about the RAM, notice one dimm is "Critical" Memory Information Health : Critical Memory Operating Mode Fail Over State : Inactive Memory Operating Mode Configuration : Optimizer Attributes of Memory Array(s) Attributes : Location Memory Array 1 : System Board or Motherboard Attributes : Use Memory Array 1 : System Memory Attributes : Installed Capacity Memory Array 1 : 12288 MB Attributes : Maximum Capacity Memory Array 1 : 196608 MB Attributes : Slots Available Memory Array 1 : 18 Attributes : Slots Used Memory Array 1 : 6 Attributes : ECC Type Memory Array 1 : Multibit ECC Total of Memory Array(s) Attributes : Total Installed Capacity Value : 12288 MB Attributes : Total Installed Capacity Available to the OS Value : 12004 MB Attributes : Total Maximum Capacity Value : 196608 MB Details of Memory Array 1 Index : 0 Status : Ok Connector Name : DIMM_A1 Type : DDR3-Registered Size : 2048 MB Index : 1 Status : Ok Connector Name : DIMM_A2 Type : DDR3-Registered Size : 2048 MB Index : 2 Status : Ok Connector Name : DIMM_A3 Type : DDR3-Registered Size : 2048 MB Index : 3 Status : Critical Connector Name : DIMM_B1 Type : DDR3-Registered Size : 2048 MB Index : 4 Status : Ok Connector Name : DIMM_B2 Type : DDR3-Registered Size : 2048 MB Index : 5 Status : Ok Connector Name : DIMM_B3 Type : DDR3-Registered Size : 2048 MB the command free -m shows this, the server seems to be using more than 10GB of ram which would suggest it is trying to use the DIMM total used free shared buffers cached Mem: 12004 10766 1238 0 384 4809 -/+ buffers/cache: 5572 6432 Swap: 2047 0 2047 iostat output while problem is occuring avg-cpu: %user %nice %system %iowait %steal %idle 52.82 0.00 11.01 0.00 0.00 36.17 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 47.00 0.00 576.00 0 576 sda1 0.00 0.00 0.00 0 0 sda2 1.00 0.00 32.00 0 32 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 46.00 0.00 544.00 0 544 avg-cpu: %user %nice %system %iowait %steal %idle 53.12 0.00 7.81 0.00 0.00 39.06 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 592.00 0 592 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 592.00 0 592 avg-cpu: %user %nice %system %iowait %steal %idle 56.09 0.00 7.43 0.37 0.00 36.10 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 232.00 0.00 64520.00 0 64520 sda1 0.00 0.00 0.00 0 0 sda2 159.00 0.00 63728.00 0 63728 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 73.00 0.00 792.00 0 792 avg-cpu: %user %nice %system %iowait %steal %idle 52.18 0.00 9.24 0.06 0.00 38.51 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 600.00 0 600 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 600.00 0 600 avg-cpu: %user %nice %system %iowait %steal %idle 54.82 0.00 8.64 0.00 0.00 36.55 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 100.00 0.00 2168.00 0 2168 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 100.00 0.00 2168.00 0 2168 avg-cpu: %user %nice %system %iowait %steal %idle 54.78 0.00 6.75 0.00 0.00 38.48 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 84.00 0.00 896.00 0 896 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 84.00 0.00 896.00 0 896 avg-cpu: %user %nice %system %iowait %steal %idle 54.34 0.00 7.31 0.00 0.00 38.35 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 81.00 0.00 840.00 0 840 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 81.00 0.00 840.00 0 840 avg-cpu: %user %nice %system %iowait %steal %idle 55.18 0.00 5.81 0.44 0.00 38.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 317.00 0.00 105632.00 0 105632 sda1 0.00 0.00 0.00 0 0 sda2 224.00 0.00 104672.00 0 104672 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 93.00 0.00 960.00 0 960 avg-cpu: %user %nice %system %iowait %steal %idle 55.38 0.00 7.63 0.00 0.00 36.98 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 74.00 0.00 800.00 0 800 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 74.00 0.00 800.00 0 800 avg-cpu: %user %nice %system %iowait %steal %idle 56.43 0.00 7.80 0.00 0.00 35.77 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 72.00 0.00 784.00 0 784 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 72.00 0.00 784.00 0 784 avg-cpu: %user %nice %system %iowait %steal %idle 54.87 0.00 6.49 0.00 0.00 38.64 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 80.20 0.00 855.45 0 864 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 80.20 0.00 855.45 0 864 avg-cpu: %user %nice %system %iowait %steal %idle 57.22 0.00 5.69 0.00 0.00 37.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 33.00 0.00 432.00 0 432 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 33.00 0.00 432.00 0 432 avg-cpu: %user %nice %system %iowait %steal %idle 56.03 0.00 7.93 0.00 0.00 36.04 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 41.00 0.00 560.00 0 560 sda1 0.00 0.00 0.00 0 0 sda2 2.00 0.00 88.00 0 88 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 39.00 0.00 472.00 0 472 avg-cpu: %user %nice %system %iowait %steal %idle 55.78 0.00 5.13 0.00 0.00 39.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 29.00 0.00 392.00 0 392 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 29.00 0.00 392.00 0 392 avg-cpu: %user %nice %system %iowait %steal %idle 53.68 0.00 8.30 0.06 0.00 37.95 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 78.00 0.00 4280.00 0 4280 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 78.00 0.00 4280.00 0 4280

  Read the article

• Linux networking crash: best steps to find out the cause?

  - by Aron Rotteveel

  One of our Linux (CentOS) servers was unreachable last night. The server was not reachable in any way except for the remote console. After logging in with the remote console, it turned out I could not ping any outside hosts either. A simple service network restart solved the issue, but I am still wondering what could have caused this. My log files seem to indicate no error at all (except for the various daemons that need a network connection and failed after the network failure). Are there any additional steps I can take to find out the cause of this problem? EDIT: this just happened again. The server was completely unresponsive until I issued a networking service restart. Any advise is welcome. Could this be caused by a faulty hardware component? As per Madhatters request, here are some excerpts from the log at the time (the network crashed at 20:13): /var/log/messages: Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=100 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:13:34 graviton junglediskserver: Connection to gateway failed: xGatewayTransport - Connection to gateway failed. The first three messages are simple responses to iptables rules I have set up through the LFD firewall. The last message indicates that JungleDisk, which I use for backups can no longer connect to the gateway. Apart from this, there are no interesting messages around this time. EDIT 4 dec: as per Mattdm's request, here is the output of ethtool eth0: (Please not that these are the settings that currently work. If things go wrong again, I will be sure to post this again if necessary. Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Link detected: yes As per Joris' request, here is also the output of route -n: aron@graviton [~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.58 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.42 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.43 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.41 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.46 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.47 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.44 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.45 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.50 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.51 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.48 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.49 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.54 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.52 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.53 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 xx.xx.xx.62 0.0.0.0 UG 0 0 0 eth0 The bottom xx.62 is my gateway. EDIT december 28th: the problem occurred again and I got the chance to compare some of the outputs of the above tests. What I found out is that arp -an returns an incomplete MAC address for my gateway (which is not under my control; the server is in a shared rack): During failure: ? (xx.xx.xx.62) at <incomplete> on eth0 After service network restart: ? (xx.xx.xx.62) at 00:00:0C:9F:F0:30 [ether] on eth0 Is this something I can fix or is it time for me to contact the data centre?

  Read the article

• Can't configure PAM + LDAP on Debian Lenny - Getting error=49 on server logs

  - by Jorge Suárez de Lis

  I've been migrating some servers and desktops using Ubuntu 10.04 from getting the users from an old OpenLDAP implementation to a newer Centos Active Directory. I haven't had any problems so far, until I reached a Debian Lenny server. I've set up the server as the others, setting /etc/ldap.conf and /etc/ldap/ldap.conf. However, when I issue "getent passwd", I get nothing from the LDAP server. Reading the pam_ldap manpage, I realized that /etc/ldap.conf was not an accepted file by pam_ldap -it worked with Ubuntu though-, so I renamed it to /etc/pam_ldap.conf. Same result. However, once I've changed the name of this file, when I login using SSH I get this on the LDAP server logs: [20/Jul/2012:11:19:40 +0200] conn=16501 fd=155 slot=155 connection from x.x.x.50 to 10.1.176.237 [20/Jul/2012:11:19:40 +0200] conn=16501 op=0 BIND dn="uid=ubuntu,ou=Applications,ou=CITIUS,dc=inv,dc=usc,dc=es" method=128 version=3 [20/Jul/2012:11:19:40 +0200] conn=16501 op=0 RESULT err=0 tag=97 nentries=0 etime=0 dn="uid=ubuntu,ou=applications,ou=citius,dc=inv,dc=usc,dc=es" [20/Jul/2012:11:19:40 +0200] conn=16501 op=1 SRCH base="ou=People,ou=CITIUS,dc=inv,dc=usc,dc=es" scope=2 filter="(uid=jorge.suarez)" attrs=ALL [20/Jul/2012:11:19:40 +0200] conn=16501 op=1 RESULT err=0 tag=101 nentries=1 etime=0 notes=U [20/Jul/2012:11:19:40 +0200] conn=16501 op=2 BIND dn="uid=jorge.suarez,ou=People,ou=CITIUS,dc=inv,dc=usc,dc=es" method=128 version=3 [20/Jul/2012:11:19:40 +0200] conn=16501 op=2 RESULT err=49 tag=97 nentries=0 etime=0 The password isn't working. I don't know that could be wrong, anything else seems to be OK. That user/password is working from another clients: [20/Jul/2012:11:29:39 +0200] conn=16528 fd=188 slot=188 connection from x.x.x.224 to 10.1.176.237 [20/Jul/2012:11:29:39 +0200] conn=16528 op=0 BIND dn="uid=ubuntu,ou=Applications,ou=CITIUS,dc=inv,dc=usc,dc=es" method=128 version=3 [20/Jul/2012:11:29:39 +0200] conn=16528 op=0 RESULT err=0 tag=97 nentries=0 etime=0 dn="uid=ubuntu,ou=applications,ou=citius,dc=inv,dc=usc,dc=es" [20/Jul/2012:11:29:39 +0200] conn=16528 op=1 SRCH base="ou=People,ou=CITIUS,dc=inv,dc=usc,dc=es" scope=2 filter="(uid=jorge.suarez)" attrs=ALL [20/Jul/2012:11:29:39 +0200] conn=16528 op=1 RESULT err=0 tag=101 nentries=1 etime=0 notes=U [20/Jul/2012:11:29:39 +0200] conn=16528 op=2 BIND dn="uid=jorge.suarez,ou=People,ou=CITIUS,dc=inv,dc=usc,dc=es" method=128 version=3 [20/Jul/2012:11:29:39 +0200] conn=16528 op=2 RESULT err=0 tag=97 nentries=0 etime=0 dn="uid=jorge.suarez,ou=people,ou=citius,dc=inv,dc=usc,dc=es" I'm using SSHA for storing passwords on the LDAP server. Maybe this is not supported by Debian Lenny? On pam_ldap.conf, I've set up this, as in all the other servers: # Do not hash the password at all; presume # the directory server will do it, if # necessary. This is the default. pam_password md5 Also tried clear, but it didn't work. Anyways, it's weird that issuing getent passwd still gets me no users. However, if I use pamtest from the package libpam-dotfile to test login, it works. # pamtest ssh jorge.suarez Trying to authenticate <jorge.suarez> for service <ssh>. Password: Authentication successful. # pamtest foo jorge.suarez Trying to authenticate <jorge.suarez> for service <foo>. Password: Authentication successful. But "su" won't work also: # su jorge.suarez Id. descoñecido: jorge.suarez Just the output from getent passwd : # getent passwd root:x:0:0:root:/root:/bin/bash daemon:x:1:1:daemon:/usr/sbin:/bin/sh bin:x:2:2:bin:/bin:/bin/sh sys:x:3:3:sys:/dev:/bin/sh sync:x:4:65534:sync:/bin:/bin/sync games:x:5:60:games:/usr/games:/bin/sh man:x:6:12:man:/var/cache/man:/bin/sh lp:x:7:7:lp:/var/spool/lpd:/bin/sh mail:x:8:8:mail:/var/mail:/bin/sh news:x:9:9:news:/var/spool/news:/bin/sh uucp:x:10:10:uucp:/var/spool/uucp:/bin/sh proxy:x:13:13:proxy:/bin:/bin/sh www-data:x:33:33:www-data:/var/www:/bin/sh backup:x:34:34:backup:/var/backups:/bin/sh list:x:38:38:Mailing List Manager:/var/list:/bin/sh irc:x:39:39:ircd:/var/run/ircd:/bin/sh gnats:x:41:41:Gnats Bug-Reporting System (admin):/var/lib/gnats:/bin/sh nobody:x:65534:65534:nobody:/nonexistent:/bin/sh libuuid:x:100:101::/var/lib/libuuid:/bin/sh Debian-exim:x:101:103::/var/spool/exim4:/bin/false statd:x:102:65534::/var/lib/nfs:/bin/false sshd:x:104:65534::/var/run/sshd:/usr/sbin/nologin luser:x:1000:1000:Usuario local de Burdeos,,,:/home/luser:/bin/bash messagebus:x:105:107::/var/run/dbus:/bin/false sge-admin:x:1001:1001:Administrador do SGE,,,:/home/cluster/sge-admin:/bin/bash ntp:x:107:110::/home/ntp:/bin/false haldaemon:x:108:111:Hardware abstraction layer,,,:/var/run/hald:/bin/false vde2-net:x:109:114::/var/run/vde2:/bin/false uml-net:x:110:115::/home/uml-net:/bin/false polkituser:x:111:116:PolicyKit,,,:/var/run/PolicyKit:/bin/false Debian-pxe:x:113:65534:Dummy user for Debian pxe package,,,:/home/Debian-pxe:/bin/false Nscd was stopped from the beginning.

  Read the article

• Recover RAID 5 data after created new array instead of re-using

  - by Brigadieren

  Folks please help - I am a newb with a major headache at hand (perfect storm situation). I have a 3 1tb hdd on my ubuntu 11.04 configured as software raid 5. The data had been copied weekly onto another separate off the computer hard drive until that completely failed and was thrown away. A few days back we had a power outage and after rebooting my box wouldn't mount the raid. In my infinite wisdom I entered mdadm --create -f... command instead of mdadm --assemble and didn't notice the travesty that I had done until after. It started the array degraded and proceeded with building and syncing it which took ~10 hours. After I was back I saw that that the array is successfully up and running but the raid is not I mean the individual drives are partitioned (partition type f8 ) but the md0 device is not. Realizing in horror what I have done I am trying to find some solutions. I just pray that --create didn't overwrite entire content of the hard driver. Could someone PLEASE help me out with this - the data that's on the drive is very important and unique ~10 years of photos, docs, etc. Is it possible that by specifying the participating hard drives in wrong order can make mdadm overwrite them? when I do mdadm --examine --scan I get something like ARRAY /dev/md/0 metadata=1.2 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b name=<hostname>:0 Interestingly enough name used to be 'raid' and not the host hame with :0 appended. Here is the 'sanitized' config entries: DEVICE /dev/sdf1 /dev/sde1 /dev/sdd1 CREATE owner=root group=disk mode=0660 auto=yes HOMEHOST <system> MAILADDR root ARRAY /dev/md0 metadata=1.2 name=tanserv:0 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b Here is the output from mdstat cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[0] sdf1[3] sde1[1] 1953517568 blocks super 1.2 level 5, 512k chunk, algorithm 2 [3/3] [UUU] unused devices: <none> fdisk shows the following: fdisk -l Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000bf62e Device Boot Start End Blocks Id System /dev/sda1 * 1 9443 75846656 83 Linux /dev/sda2 9443 9730 2301953 5 Extended /dev/sda5 9443 9730 2301952 82 Linux swap / Solaris Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de8dd Device Boot Start End Blocks Id System /dev/sdb1 1 91201 732572001 8e Linux LVM Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00056a17 Device Boot Start End Blocks Id System /dev/sdc1 1 60801 488384001 8e Linux LVM Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ca948 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/dm-0: 1250.3 GB, 1250254913536 bytes 255 heads, 63 sectors/track, 152001 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x93a66687 Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xe6edc059 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/md0: 2000.4 GB, 2000401989632 bytes 2 heads, 4 sectors/track, 488379392 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1048576 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Per suggestions I did clean up the superblocks and re-created the array with --assume-clean option but with no luck at all. Is there any tool that will help me to revive at least some of the data? Can someone tell me what and how the mdadm --create does when syncs to destroy the data so I can write a tool to un-do whatever was done? After the re-creating of the raid I run fsck.ext4 /dev/md0 and here is the output root@tanserv:/etc/mdadm# fsck.ext4 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Superblock invalid, trying backup blocks... fsck.ext4: Bad magic number in super-block while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 Per Shanes' suggestion I tried root@tanserv:/home/mushegh# mkfs.ext4 -n /dev/md0 mke2fs 1.41.14 (22-Dec-2010) Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=128 blocks, Stripe width=256 blocks 122101760 inodes, 488379392 blocks 24418969 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 14905 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 and run fsck.ext4 with every backup block but all returned the following: root@tanserv:/home/mushegh# fsck.ext4 -b 214990848 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Invalid argument while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> Any suggestions? Regards!

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• Sporadic disk clicking sound

  - by Abdó

  Hi, I'm having some unusual and sporadic hard disk clicking issues. Here is a cronological description of the facts. I'm using an ASUS P6T-SE with Intel Core i7, 6Gb RAM 600W Power supply and ATI4670 graphics, running Ubuntu 10.10. About one month ago my hard disk (SATA II Seagate Barracuda 1Tb 7200 rpm) started making a clicking sound: a sort of loud tic-tac, every second or so, when involved in disk activity. The system was clearly slower than before at disk access, but it was functional and I could not find any signal of trouble on the linux logs. I disconnected the disk and tried an older SATA drive I had around: no problem with it. Then I reconnected the Seagate disk, and the problem was mysteriously gone. Ubuntu booted normally, usual speed, no clicking. A couple of weeks later, the problem reappeared. I tried disconnecting reconnecting (as it somehow solved the problem before) without luck. So, despite it was a rather new drive, I assumed it was a hardware issue, made backups and bought a new drive. The new drive is a SATA II Seagate Barracuda 1.5 Tb 7200 rpm. I installed both drives at the same time, with the intention of transferring my files from on to the other. To my surprise, when I booted the computer with both drives, both started making the clicking sound !! Even worse, I removed the old drive, leaving the unformated new drive connected, and booted from a LiveCD. It kept clicking ! Puzzled by this, I tried both drives on my laptop with a SATA to USB cable. At the moment I connected any of them, they made one or two unusual clicks and immediately stopped doing that and worked normally. The old drive I thought almost dead, was working like a charm as if nothing happened. Then I thought: "ok, it must be the motherboard. Let's try again". So, I reconnected the old drive to the ASUS P6T motherboard (the same cables and SATA port as before), and it worked as if nothing happened ! The problem was gone again. The new 1.5 Tb drive was also working ok: No clicking nor slowdown. So I left the old 1Tb disk connected and kept using the computer daily during 3 weeks, until today it happened again. Now I don't really know what to do or check. I'm not even sure if it is a hardware issue any more ! This is rather annoying as it seems it happens with a period of 2 or 3 weeks and I have no means of forcing it to happen. Does anyone have a clue of what can causes this behaviour or have any suggestions of things I should check when it happens again ? What I did today is checking some SMART parameters Error log: smartctl -l error /dev/sda. No errors Short selftest: smartctl -t short /dev/sda. No errors Disk Health check: smartctl -H /dev/sda. passed And here are the vendor specific parameters (smartctl -A /dev/sda) Which I'm not quite sure how to interpret. === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 120 099 006 Pre-fail Always - 235962588 3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 187 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 16348045 9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 3590 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 94 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 097 000 Old_age Always - 4295164029 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 070 057 045 Old_age Always - 30 (Lifetime Min/Max 19/31) 194 Temperature_Celsius 0x0022 030 043 000 Old_age Always - 30 (0 18 0 0) 195 Hardware_ECC_Recovered 0x001a 037 026 000 Old_age Always - 235962588 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 73950746906346 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1832967731 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3294986902 Any clue to this mystery will be really welcome. Thank you very much !!

  Read the article

• CSC folder data access AND roaming profiles issues (Vista with Server 2003, then 2008)

  - by Alex Jones

  I'm a junior sysadmin for an IT contractor that helps small, local government agencies, like little towns and the like. One of our clients, a public library with ~ 50 staff users, was recently migrated from Server 2003 Standard to Server 2008 R2 Standard in a very short timeframe; our senior employee, the only network engineer, had suddenly put in his two weeks notice, so management pushed him to do this project before quitting. A bit hasty on management's part? Perhaps. Could we do anything about that? Nope. Do I have to fix this all by myself? Pretty much. The network is set up like this: a) 50ish staff workstations, all running Vista Business SP2. All staff use MS Outlook, which uses RPC-over-HTTPS ("Outlook Anywhere") for cached Exchange access to an offsite location. b) One new (virtualized) Server 2008 R2 Standard instance, running atop a Server 2008 R2 host via Hyper-V. The VM is the domain's DC, and also the site's one and only file server. Let's call that VM "NEWBOX". c) One old physical Server 2003 Standard server, running the same roles. Let's call it "OLDBOX". It's still on the network and accessible, but it's been demoted, and its shares have been disabled. No data has been deleted. c) Gigabit Ethernet everywhere. The organization's only has one domain, and it did not change during the migration. d) Most users were set up for a combo of redirected folders + offline files, but some older employees who had been with the organization a long time are still on roaming profiles. To sum up: the servers in question handle user accounts and files, nothing else (eg, no TS, no mail, no IIS, etc.) I have two major problems I'm hoping you can help me with: 1) Even though all domain users have had their redirected folders moved to the new server, and loggin in to their workstations and testing confirms that the Documents/Music/Whatever folders point to the new paths, it appears some users (not laptops or anything either!) had been working offline from OLDBOX for a long time, and nobody realized it. Here's the ugly implication: a bunch of their data now lives only in their CSC folders, because they can't access the share on OLDBOX and sync with it finally. How do I get this data out of those CSC folders, and onto NEWBOX? 2) What's the best way to migrate roaming profile users to non-roaming ones, without losing vital data like documents, any lingering PSTs, etc? Things I've thought about trying: For problem 1: a) Reenable the documents share on OLDBOX, force an Offline Files sync for ALL domain users, then copy OLDBOX's share's data to the equivalent share on NEWBOX. Reinitialize the Offline Files cache for every user. With this: How do I safely force a domain-wide Offline Files sync? Could I lose data by reenabling the share on OLDBOX and forcing the sync? Afterwards, how can I reinitialize the Offline Files cache for every user, without doing it manually, workstation by workstation? b) Determine which users have unsynced changes to OLDBOX (again, how?), search each user's CSC folder domain-wide via workstation admin shares, and grab the unsynched data. Reinitialize the Offline Files cache for every user. With this: How can I detect which users have unsynched changes with a script? How can I search each user's CSC folder, when the ownership and permissions set for CSC folders are so restrictive? Again, afterwards, how can I reinitialize the Offline Files cache for every user, without doing it manually, workstation by workstation? c) Manually visit each workstation, copy the contents of the CSC folder, and manually copy that data onto NEWBOX. Reinitialize the Offline Files cache for every user. With this: Again, how do I 'break into' the CSC folder and get to its data? As an experiment, I took one workstation's HD offsite, imaged it for safety, and then tried the following with one of our shop PCs, after attaching the drive: grant myself full control of the folder (failed), grant myself ownership of the folder (failed), run chkdsk on the whole drive to make sure nothing's messed up (all OK), try to take full control of the entire drive (failed), try to take ownership of the entire drive (failed) MS KB articles and Googling around suggests there's a utility called CSCCMD that's meant for this exact scenario...but it looks like it's available for XP, not Vista, no? Again, afterwards, how can I reinitialize the Offline Files cache for every user, without doing it manually, workstation by workstation? For problem 2: a) Figure out which users are on roaming profiles, and where their profiles 'live' on the server. Create new folders for them in the redirected folders repository, migrate existing data, and disable the roaming. With this: Finding out who's roaming isn't hard. But what's the best way to disable the roaming itself? In AD Users and Computers, or on each user's workstation? Doing it centrally on the server seems more efficient; that said, all of the KB research I've done turns up articles on how to go from local to roaming, not the other way around, so I don't have good documentation on this. In closing: we have good backups of NEWBOX and OLDBOX, but not of the workstations themselves, so anything drastic on the client side would need imaging and testing for safety. Thanks for reading along this far! Hopefully you can help me dig us out of this mess.

  Read the article

• Should I go along with my choice of web hosting company or still search?

  - by Devner

  Hi all, I have been searching for a good website hosting company that can offer me all the services that I need for hosting my PHP & MySQL based website. Now this is a community based website and users will be able to upload pictures, etc. The hosting company that I have in mind, currently lets me do everything... let me use mail(), supports CRON jobs, etc. Of course they are charging about $6/month. Now the only problem with this company is that they have a limit of 50,000 files that can exist within the hosting account at any time. This kind of contradicts their frontpage ad of "UNLIMITED SPACE" on their website. Apart from this, I know of no other reason why I should not go with this hosting company. But my issue is that 50,000 file limit is what I cannot live with, once the users increase in significant number and the files they upload, exceed 50,000 in number. Now since this is a dynamic website and also includes sensitive issues like payments, etc. I am not sure if I should go ahead with this company as I am just starting out and then later switch over to a better hosting company which does not limit me with 50,000 files. If I need to switch over once I host with this company, I will need to take backups of all the files located in my account (jpg, zip, etc.), then upload them to the new host. I am not aware of any tools that can help me in this process. Can you please mention if you know any? I can go ahead with the other companies right now, but their cost is double/triple of the current price and they all sport less features than my current choice. If I pay more, then they are ready to accommodate my higher demands. Unfortunately, the company that I am willing to go with now, does NOT have any other higher/better plans that I can switch to. So that's the really really bad part. So my question(s): Since I am starting out with my website and since the scope of users initially is going to be less/small, should I go ahead with the current choice and then once the demand increases, switch over to a better provider? If yes, how can I transfer my database, especially the jpg files, etc. to the new provider? I don't even know the tools required to backup and restore to another host. (I don't like this idea but still..) Should I go ahead and pay more right now and go with better providers (without knowing if the website is going to do really that well) just for saving myself the trouble of having to take a backup of the 50,000 files and upload to a new host from an old host and just start paying double/triple the price without even knowing if I would receive back the returns as I expected? Backup and Restore in such a bulky numbers is something that I have never done before and hence I am stuck here trying to decide what to do. The price per month is also a considerable factor in my decision. All these web hosting companies say one common thing: It is customers responsibility to backup and restore data and they are not liable for any loss. So no matter what hosting company that I would like to go with, they ask me to take backup via FTP so that I can restore them whenever I want (& it seems to be safer to have the files locally with me). Some are providing tools for backup and some are not and I am not sure how much their backup tools can be trusted considering the disclaimers they have. I have never backed-up and restored 50,000 files from one web host to another, so please, all you experienced people out there, leave your comments and let me know your suggestions so that I can decide. I have spent 2 days fighting with myself trying to decide what to do and finally concluded that this is a double-edged sword and I can't arrive at a satisfactory final decision without involving others suggestions. I believe that someone must be out there who may have had such troublesome decision to make. So all your suggestions to help me make my decision are appreciated. Thank you all.

  Read the article

• Remotely Schedule and Stream Recorded TV in Windows 7 Media Center

  - by DigitalGeekery

  Have you ever been away from home and suddenly realized you forgot to record your favorite program? Now Windows 7 Media Center, users can schedule recordings remotely from their phones or mobile devices with Remote Potato. How it Works Remote Potato installs server software on the host computer running Windows 7 Media Center. Once the software is installed, we’ll need to do some port forwarding on the router and setup an optional dynamic DNS address. When setup is completed, we will access the application through a web based interface. Silverlight is required for Streaming recorded TV, but scheduling recordings can be done through an HTML interface. Installing Remote Potato Download and install Remote Potato on the Media Center PC. (See download link below) If you plan to stream any Recorded TV, you’ll also want to install the streaming pack located on the same page. It isn’t required to stream all shows, only shows that require the AC3 audio codec. Click Yes to allow Remote Potato to add rules to the Windows Firewall for remote access. You’ll likely need to accept a few UAC prompts. When notified that the rules were added, click OK. Remote Potato will then prompt you to allow administrator privileges to reserve a URL for it’s web server. Click Yes. Remote Potato server will start. Click on the configuration button at the right to to reveal the settings tabs.   One the General tab, you’ll have the option to run Remote Potato on startup and minimized in the System Tray. If you’re running Media Center on a dedicated HTPC, you’ll probably want to enable both startup options. Forwarding Ports on Your Router You’ll need to forward a couple ports on your router. By default, these will be ports 9080 and 9081. In this example we’re using a Linksys WRT54GL router, however, the steps for port forwarding will vary from router to router. On the Linksys configuration page, click on the Applications & Gaming Tab, and then the Port Range Forward tab. Under Application, type in a name of your choosing. In both the Start and End boxes, type the port number 9080. Enter the local IP address of your Media Center computer in the IP address column. Click the check box under Enable. Repeat the process on the next line, but this time use port 9081. When finished, click the Save Settings button. Note: It’s highly recommended that you configure the home computer running Media Center & Remote Potato with a static IP address.   Find your IP Address You’ll need to find the IP address assigned to your router from your ISP. There are many ways to do this but a quick and easy way is to visit a site like checkip.dyndns.org (link available below) The current external IP address of your router will be displayed in the browser.   Dynamic DNS This is an optional step, but  it’s highly recommended. Many routers, such as the Linksys WRT54GL we are using, support Dynamic DNS (DDNS). What Dynamic DNS allows you to do is affiliate your home router’s external IP address to a domain name. Every time your home router is assigned a a new IP address by your ISP, the domain name is updated to point to your new IP address. Remote Potato’s user interface is accessed over the Internet is by connecting to your router’s IP address followed by a colon and the port number. (Ex: XXX.XXX.XXX.XXX:9080) Instead of constantly having to look up and remember an IP address, you can use DDNS along with a 3rd party provider like DynDNS.com, to sign up for a free domain name and configure it to be updated each time your router is assigned a new IP address. Go to the DynDNS.com website (See link at the end of the article) and sign up for a free Domain name. You’ll need to register and confirm by email.   Once you’ve signed in and selected your domain name click Activate Services. You’ll get a confirmation message that your domain name has been activated.    On the Linksys WRT54GL click on the Setup tab an then DDNS. Select DynDNS.org, or TZO.com if you prefer to use their service, from the drop down list.   With DynDNS, you’ll need to fill in your username and password you signed up with at the DynDNS website and the hostname you chose. Note: You can connect over your local network with the IP Address of the computer running Remote Potato followed by a colon and the port number. Ex: 192.168.1.2:9080 Logging in Remote Potato and Recording a Show Once you connect, you’ll see the start page. To view the TV listings, click on TV Guide. You’ll then see your guide listings. There are a few ways to navigate the listings. At the top left, you can click on any of the preset time buttons to jump to  the listings at that time of the day.  Click on the arrows to the right and left of the day and date at the top center to proceed to the previous or next day. Or, jump to a specific day with the date and date buttons at the top right.   To setup a recording, click on a program.   You can choose to record the individual show or the entire series by clicking on Record Show or Record Series.   Remote Potato on Mobile Devices Perhaps the coolest feature of Remote Potato is the ability to schedule recording from your phone or mobile device. Note: For any devices or computers without Silverlight, you will be prompted to view the HTML page. Select Browse Listings. Select your program to record. In the Program Details, select Record Show to record the single episode or Record Series to record all instances of the series. You will then see a red dot on the program listing to indicate that the show is scheduled for recording.   Streaming Recorded TV Click on Recorded TV from the home screen to access your previously recorded TV programs. Click on the selection you wish to stream. Click on Play. If you receive this error message, you’ll need to install the streaming pack for Remote Potato. This is found on the same download page as installation files. (See link below) The Begin from slider allows you to start playback from the start (by default) or a different time of the program by moving the slider. The Quality (bitrate) setting  allows you to choose the quality of the playback. We found the video quality on the Normal setting to be pretty lousy, and Low was just pointless. High was the best overall viewing experience as it provided smooth quality video playback. We experienced significant stuttering during playback using the Ultra High setting.   Click Start when you are ready to begin. When playback begins you’ll see a slider at the top right.   Move the slider left or right to increase or decrease the size of the video. There’s also a button to switch to full screen.   Media Center users who travel frequently or are always on the go will likely find Remote Potato to be a blessing. Since being released earlier this year, updates for Remote Potato have come fast and furious. The latest beta release includes support for streaming music and photos. If you like those nice network TV logos, check out our article on adding TV channel logos to Windows Media Center. Downloads and Links Download Remote Potato and Streaming Pack Find your IP address Sign Up for a Domain Name at DynDNS.com Similar Articles Productive Geek Tips Schedule Updates for Windows Media CenterUsing Netflix Watchnow in Windows Vista Media Center (Gmedia)Add a Sleep Timer to Windows 7 Media CenterStartup Customizations for Media Center in Windows 7Enable Media Streaming in Windows Home Server to Windows Media Player TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 FoxClocks adds World Times in your Statusbar (Firefox) Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos

  Read the article

• CodePlex Daily Summary for Saturday, March 06, 2010

  CodePlex Daily Summary for Saturday, March 06, 2010New ProjectsAgr.CQRS: Agr.CQRS is a C# framework for DDD applications that use the Command Query Responsibility Segregation pattern (CQRS) and Event Sourcing. BigDays 2010: Big>Days 2010BizTalk - Controlled Admin: Hi .NET folks, I am planning to start project on a Controlled BizTalk Admin tool. This tool will be useful for the organizations which have "Sh...Blacklist of Providers: Blacklist of Providers - the application for department of warehouse logistics (warehouse) at firms.Career Vector: A job board software.Chargify Demo: This is a sample website for ChargifyConceptual: Concept description and animationEric Hexter: My publicly available source code and examplesFluentNHibernate.Search: A Fluent NHibernate.Search mapping interface for NHibernate provider implementation of Lucene.NET.FreelancePlanner: FreelancePlanner is a project tracking tool for freelance translators.HTMLx - JavaScript on the Server for .NET: HTMLx is a set of libraries based on ASP.NET engine to provide JavaScript programmability on the server side. It allows Web developers to use JavaS...IronMSBuild: IronMSBuild is a custom MSBuild Task, which allows you to execute IronRuby scripts. // have to provide some examples LINQ To Blippr: LINQ to Blippr is an open source LINQ Provider for the micro-reviewing service Blippr. LINQ to Blippr makes it easier and more efficent for develo...Luk@sh's HTML Parser: library that simplifies parsing of the HTML documents, for .NETMeta Choons: Unsure as yet but will be a kind of discogs type site but different..NetWork2: NetWork2Regular Expression Chooser: Simple gui for choosing the regular expressions that have become more than simple.See.Sharper: Hopefully useful C# extensions.SharePoint 2010 Toggle User Interface: Toggle the SharePoint 2010 user interface between the new SharePoint 2010 user interface and SharePoint 2007 user interface.Silverlight DiscussionBoard for SharePoint: This is a sharepoint 3.0 webpart that uses a silverlight treeview to display metadata about sharepoint discussions anduses the html bridge to show...Simple Sales Tracking CRM API Wrapper: The Simple Sales Tracking API Wrapper, enables easy extention development and integration with the hosted service at http://www.simplesalestracking...Syntax4Word: A syntax addin for word 2007.TortoiseHg installer builder: TortoiseHg and Mercurial installer builder for Windowsunbinder: Model un binding for route value dictionariesWindows Workflow Foundation on Codeplex: This site has previews of Workflow features which are released out of band for the purposes of adoption and feedback.XNA RSM Render State Manager: Render state management idea for XNA games. Enables isolation between draw calls whilst reducing DX9 SetRenderState calls to the minimum.New ReleasesAgr.CQRS: Sourcecode package: Agr.CQRS is a C# framework for DDD applications that use the Command Query Responsibility Segregation pattern (CQRS) and Event Sourcing. This dow...Book Cataloger: Preview 0.1.6a: New Features: Export to Word 2007 Bibliography format Dictionary list editors for Binding, Condition Improvements: Stability improved Content ...Braintree Client Library: Braintree-1.1.2: Includes minor enhancements to CreditCard and ValidationErrors to support upcoming example application.CassiniDev - Cassini 3.5 Developers Edition: CassiniDev v3.5.0.5: For usage see Readme.htm in download. New in CassiniDev v3.5.0.5 Reintroduced the Lib project and signed all Implemented the CassiniSqlFixture -...Composure: Calcium-64420-VS2010rc1.NET4.SL3: This is a simple conversion of Calcium (rev 64420) built in VS2010 RC1 against .NET4 and Silverlight 3. No source files were changed and ALL test...Composure: MS AJAX Library (46266) for VS2010 RC1 .NET4: This is a quick port of Microsoft's AJAX Library (rev 46266) for Visual Studio 2010 RC1 built against .NET 4.0. Since this conversion was thrown t...Composure: MS Web Test Lightweight for VS2010 RC1 .NET4: A simple conversion of Microsoft's Web Test Lightweight for Visual Studio 2010 RC1 .NET 4.0. This is part of a larger "special request" conversion...CoNatural Components: CoNatural Components 1.5: Supporting new data types: Added support for binary data types -> binary, varbinary, etc maps to byte[] Now supporting SQL Server 2008 new types ...Extensia: Extensia 2010-03-05: Extensia is a very large list of extension methods and a few helper types. Some extension methods are not practical (e.g. slow) whilst others are....Fluent Assertions: Fluent Assertions release 1.1: In this release, we've worked hard to add some important missing features that we really needed, and also improve resiliance against illegal argume...Fluent Ribbon Control Suite: Fluent Ribbon Control Suite 1.0 RC: Fluent Ribbon Control Suite 1.0 (Release Candidate)Includes: Fluent.dll (with .pdb and .xml, debug and release version) Showcase Application Sa...FluentNHibernate.Search: 0.1 Beta: First beta versionFolderSize: FolderSize.Win32.1.0.7.0: FolderSize.Win32.1.0.6.0 A simple utility intended to be used to scan harddrives for the folders that take most place and display this to the user...Free Silverlight & WPF Chart Control - Visifire: Silverlight and WPF Step Line Chart: Hi, With this release Visifire introduces Step Line Chart. This release also contains fix for the following issues: * In WPF, if AnimatedUpd...Html to OpenXml: HtmlToOpenXml 1.0: The dll library to include in your project. The dll is signed for GAC support. Compiled with .Net 3.5, Dependencies on System.Drawing.dll and Docu...Line Counter: 1.5.1: The Line Counter is a tool to calculate lines of your code files. The tool was written in .NET 2.0. Line Counter 1.5.1 Added outline icons and lin...Lokad Cloud - .NET O/C mapper (object to cloud) for Windows Azure: Lokad.Cloud v1.0.662.1: You can get the most recent release directly from the build server at http://build.lokad.com/distrib/Lokad.Cloud/Lost in Translation: LostInTranslation v0.2: Alpha release: function complete but not UX complete.MDownloader: MDownloader-0.15.7.56349: Supported large file resumption. Fixed minor bugs.Mini C# Lab: Mini CSharp Lab Ver 1.4: The primary new feature of Ver 1.4 is batch mode! Now you can run Mini C# Lab program as a scheduled task, no UI interactivity is needed. Here ar...Mobile Store: First drop: First droppatterns & practices SharePoint Guidance: SPG2010 Drop6: SharePoint Guidance Drop Notes Microsoft patterns and practices ****************************************** ***************************************...Picasa Downloader: PicasaDownloader (41446): Changelog: Replaced some exception messages by a Summary dialog shown after downloading if there have been problems. Corrected the Portable vers...Pod Thrower: Version 1: This is the first release, I'm sure there are bugs, the tool is fully functional and I'm using it currently.PowerShell Provider BizTalk: BizTalkFactory PowerShell Provider - 1.1-snapshot: This release constitutes the latest development snapshot for the Provider. Please, leave feedback and use the Issue Tracker to help improve this pr...Resharper Settings Manager: RSM 1.2.1: This is a bug fix release. Changes Fixed plug-in crash when shared settings file was modified externally.Reusable Library Demo: Reusable Library Demo v1.0.2: A demonstration of reusable abstractions for enterprise application developerSharePoint 2010 Toggle User Interface: SharePoint Toggle User Interface: Release 1.0.0.0Starter Kit Mytrip.Mvc.Entity: Mytrip.Mvc.Entity(net3.5 MySQL) 1.0 Beta: MySQL VS 2008 EF Membership UserManager FileManager Localization Captcha ClientValidation Theme CrossBrowserTortoiseHg: TortoiseHg 1.0: http://bitbucket.org/tortoisehg/stable/wiki/ReleaseNotes Please backup your user Mercurial.ini file and then uninstall any 0.9.X release before in...Visual Studio 2010 and Team Foundation Server 2010 VM Factory: Rangers Virtualization Guidance: Rangers Virtualization Guidance Focused guidance on creating a Rangers base image manually and introduction of PowerShell scripts to automate many ...Visual Studio DSite: Advanced Email Program (Visual Basic 2008): This email program can send email to any one using your email username and email credentials. The email program can also attatch attactments to you...WPF ShaderEffect Generator: WPF ShaderEffect Generator 1.6: Several improvements and bug fixes have gone into the comment parsing code for the registers. The plug-in should now correctly pay attention to th...WSDLGenerator: WSDLGenerator 0.0.0.3: - Fixed SharePoint generated *.wsdl.aspx file - Added commandline option -wsdl which does only generate the wsdl file.Most Popular ProjectsMetaSharpRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)ASP.NETLiveUpload to FacebookMicrosoft SQL Server Community & SamplesMost Active ProjectsUmbraco CMSRawrSDS: Scientific DataSet library and toolsBlogEngine.NETjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryIonics Isapi Rewrite FilterFluent AssertionsComposureDiffPlex - a .NET Diff Generator

  Read the article

• MySQL Connect: What to Expect From the Wondrous Land of MySQL Cluster

  - by Mat Keep

  The MySQL Connect conference is only a couple of weeks away, with MySQL engineers, support teams, consultants and community aces busy putting the final touches to their talks. There will be many exciting new announcements and sharing of best practices at the conference, covering the range of MySQL technologies. MySQL Cluster will a big part of this, so I wanted to share some key sessions for those of you who plan on attending, as well as some resources for those who are not lucky enough to be able to make the trip, but who can't afford to miss the key news. Of course, this is no substitute to actually being there….and the good news is that registration is still open ;-) Roadmap: Whats New in MySQL Cluster Saturday 29th, 1300-1400, in Golden Gate room 5.                                                                                        Bernd Ocklin, director of MySQL Cluster development, and myself will be taking a look at what follows the latest MySQL Cluster 7.2 release. I don't want to give to much away - lets just say its not often you can add powerful new functionality to a product while at the same time making life radically simpler for its users. For those not making it to the Conference, a live webinar repeating the talk is scheduled for Thursday 25th October at 09.00 pacific time. Hold the date, registration will be open for that soon and published to our MySQL Webinars page Best Practices Getting Started with MySQL Cluster, Hands-On Lab Saturday 29th, 1600-1700, in Plaza Room A.                                                              Santo Leto, one of our lead MySQL Cluster support engineers, regularly works with users new to MySQL Cluster, assisting them in installation, configuration, scaling, etc. In this lab, Santo will share best-practices in getting started. Delivering Breakthrough Performance with MySQL Cluster Saturday 29th, 1730-1830, in Golden Gate room 5. Frazer Clement, lead MySQL Cluster software engineer, will demonstrate how to translate the awesome Cluster benchmarks (remember 1 BILLION UPDATEs per minute ?!) into real-world performance. You can also get some best practices from our new MySQL Cluster performance guide  MySQL Cluster BoF Saturday 29th, 1900-2000, room Golden Gate 5.                                                                                                           Come and get a demonstration of new tools for the installation and configuration of MySQL Cluster, and spend time with the engineering team discussing any questions or issues you may have. Developing High-Throughput Services with NoSQL APIs to InnoDB and MySQL Cluster Sunday 30th, 1145 - 1245, in Golden Gate room 7.   In this session, JD Duncan and Andrew Morgan will present how to get started with both Memcached and new NoSQL APIs. JD and I recently ran a webinar demonstrating how to build simple Twitter-like services with Memcached and MySQL Cluster. The replay is available for download.  Case Studies: MySQL Cluster @ El Chavo, Latin America’s #1 Facebook Game Sunday 30th, 1745 - 1845, in Golden Gate room 4.                             Playful Play deployed MySQL Cluster CGE to power their market leading social game. This session will discuss the challenges they faced, why they selected MySQL Cluster and their experiences to date. You can read more about Playful Play and MySQL Cluster here  A Journey into NoSQLand: MySQL’s NoSQL Implementation Sunday 30th, 1345 - 1445, in Golden Gate room 4.                                          Lig Turmelle, web DBA at Kaplan Professional and esteemed Oracle Ace, will discuss her experiences working with the NoSQL interfaces for both MySQL Cluster and InnoDB Evaluating MySQL HA Alternatives Saturday 29th, 1430-1530, room Golden Gate 5                                                                                   Henrik Ingo, former member of the MySQL sales engineering team, will provide an overview of various HA technologies for MySQL, starting with replication, progressing to InnoDB, Galera and MySQL Cluster What about the other stuff? Of course MySQL Connect has much, much more than MySQL Cluster. There will be lots on replication (which I'll blog about soon), MySQL 5.6, InnoDB, cloud, etc, etc. Take a look at the full Content Catalog to see more. If you are attending, I hope to see you at one of the Cluster sessions...and remember, registration is still open

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113  | Next Page >