Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 109/315 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

• Internet wireless connected with limited access, windows vista

  - by r0ca

  I had some malware in my computer so I did a bit of manual work to remove it including resetting TCP/IP. Now the malware is gone. I can see my home wireless network and I can get connected to it but when connected I get the Internet wireless connected with limited access message. When I go to the IE I cannot browse. When I tried to ping 192.168.1.1 I got an Error Code 1231 Unconnected Network Problem. I have deactivated my Windows firewall as I thought it could be hyperactive security. Still no luck. I have Norton but it is not active, I have also Avast and AVG installed but they are not active. Any ideas?

  Read the article

• Western Digital My Book World drops off network

  - by Macha

  Most of my storage in my house relies on a WD My Book World Edition 500GB network drive. I threw out the vendor crapware they give you to access it (a trial version of Mionet) after it starting nagging me to upgrade, and set it up as a standard network drive using Window's Map Network Drive. However, since then, it has been dropping off the network after 30 minutes of non-usage. The only way to get it back on is to switch it off and on again at the plug socket. Does anyone know what is causing this, and hopefully how to fix it? EDIT: it's the original "blue rings" version with the latest firmware.

  Read the article

• VPN in Ubuntu fails every time

  - by fazpas

  I am trying to setup a vpn connection in Ubuntu 10.04 to use the service from relakks.com I used the network manager to add the vpn connection and the settings are: Gateway: pptp.relakks.com Username: user Password: pwd IPv4 Settings: Automatic (VPN) Advanced: MSCHAP & MSCHAPv2 checked Use point-to-point encryption (security:default) Allow BSD data compression checked Allow deflate data compression checked Use TCP header compression checked The connection always fail, here is the syslog: Jun 27 20:11:56 desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'... Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started (org.freedesktop.NetworkManager.pptp), PID 2064 Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' just appeared, activating connections Jun 27 20:11:56 desktop NetworkManager: <info> VPN plugin state changed: 3 Jun 27 20:11:56 desktop NetworkManager: <info> VPN connection 'Relakks' (Connect) reply received. Jun 27 20:11:56 desktop pppd[2067]: Plugin /usr/lib/pppd/2.4.5//nm-pptp-pppd-plugin.so loaded. Jun 27 20:11:56 desktop pppd[2067]: pppd 2.4.5 started by root, uid 0 Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp1, iface: ppp1): no ifupdown configuration found. Jun 27 20:11:56 desktop pppd[2067]: Using interface ppp1 Jun 27 20:11:56 desktop pppd[2067]: Connect: ppp1 <--> /dev/pts/0 Jun 27 20:11:56 desktop pptp[2071]: nm-pptp-service-2064 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Jun 27 20:11:57 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1 'Start-Control-Connection-Request' Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:739]: Received Start Control Connection Reply Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:773]: Client connection established. Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 0, peer's call ID 1024). Jun 27 20:11:59 desktop kernel: [ 56.564074] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=61 TOS=0x00 PREC=0x00 TTL=52 ID=40460 DF PROTO=47 Jun 27 20:11:59 desktop kernel: [ 56.944054] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=60 TOS=0x00 PREC=0x00 TTL=52 ID=40461 DF PROTO=47 Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[call_callback:pptp_callmgr.c:79]: Closing connection (call state) Jun 27 20:11:59 desktop pppd[2067]: Modem hangup Jun 27 20:11:59 desktop pppd[2067]: Connection terminated. Jun 27 20:11:59 desktop NetworkManager: <info> VPN plugin failed: 1 Jun 27 20:11:59 desktop NetworkManager: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:59 desktop pppd[2067]: Exit. Does someone can identify something in the syslog? I've been googling and reading about pptp but couldn't find anything about the error "read returned zero, peer has closed"

  Read the article

• Providing reverse records for records that map to ISP IP

  - by thejartender

  I have been instructed to use my ISP ip (as a temporary fix for mapping my name server and domain records as my router dishes out rfc 1918 adresses to devices in my network where I am running an Ubuntu server, my router and my development laptop andso I have fixed: $TTL 3H @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 10.0.0.42 @ IN NS ns.thejarbar.org. yuccalaptop IN A 10.0.0.19 ns IN A 10.0.0.42 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. To a temporary version of: $TTL 3H @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 88.89.190.171 @ IN NS ns.thejarbar.org. yuccalaptop IN A 10.0.0.19 ns IN A 88.89.190.171 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. I am using bind and when using named-checkzone on this file according to my zone configurations, this file has no errors. I then run dig thejarbar.org @88.89.190.171 and get an expected authorative reply. My issue is creating my reverse DNS SOA zone and I would gratly appreciate assistance and guidance. I am stuck on how to represent the reverse records correctly for the eddresses that map to my isp IP. I am trying: $TTL 3H 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 171.190.89.88. IN PTR thejarbar.org. 171.190.89.88. IN NS ns.thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. www IN PTR www.thejarbar.org. But running named-checkzone on this file leaves an erroneous return that IN: has no NS records I would greatly appreciate assistance

  Read the article

• Cannot access a web page?

  - by ipkiss

  Hello all, Recently, I could not access the webpage bbc.co.uk anymore, while I can access other websites smoothly. Ar first, I though there may be some problem with my laptop. However, if I use my laptop through my company network, I can load the page bbc.co.uk normally. Then, I though maybe my ADSL at home blocks that web address. However, I tried another laptop with my home ADSL and it can load the page bbc.co.uk very fast. Now I do not know what could be the problem. Can anyone tell me please? Thank you.

  Read the article

• Cannot access a web page?

  - by user40748

  Hello all, Recently, I could not access the webpage bbc.co.uk anymore, while I can access other websites smoothly. Ar first, I though there may be some problem with my laptop. However, if I use my laptop through my company network, I can load the page bbc.co.uk normally. Then, I though maybe my ADSL at home blocks that web address. However, I tried another laptop with my home ADSL and it can load the page bbc.co.uk very fast. Now I do not know what could be the problem. Can anyone tell me what could cause the issue, please? Thank you.

  Read the article

• Cannot access a web page?

  - by ipkiss

  Hello all, Recently, I could not access the webpage bbc.co.uk anymore, while I can access other websites smoothly. Ar first, I though there may be some problem with my laptop. However, if I use my laptop through my company network, I can load the page bbc.co.uk normally. Then, I though maybe my ADSL at home blocks that web address. However, I tried another laptop with my home ADSL and it can load the page bbc.co.uk very fast. Now I do not know what could be the problem. Can anyone tell me what could cause the issue, please? Thank you.

  Read the article

• Monitor HTTP usage on network from Linux free

  - by David

  I manage a small office network. I am looking to start monitoring/logging internet usage (website requests) for each user on a small network. All the windows clients are running through a switch to a BT router. I also have a linux (centos) machine which is connected as a client to the BT router as well. Is there any free software I can install on the linux box (or my own machine) to allow me to log and monitor websites requested by users kind of like browser history. Ideally, something that would collect each client's browser history in 1 place. Thanks

  Read the article

• Squid proxy in cent os often disconnected with error : tunnelConnectTimeout(): tunnelState->servers is NULL

  - by Ela

  I am having very often internet disconnection problem with Squid proxy service. My server config; OS: CentOS release 6.3 (Final) model name : Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz cpu MHz : 1600.000 My Local systems IP range:192.168.2.x Server IP: 192.168.2.11 Also this server is configured with lamp for development,Samba SMB file service manager and No svn currently. So i see maximum possibility is this squid proxy since this is where it stops to connect and am sure when i restart the server net started working so something wrong with this squid service only. And this server is connected with local 14 other windows machines and basically serves as a central development node. I am able to resolve it by restarting the server fully some time or sometimes by restarting the squid proxy which is totally killing our development. I have attached my cache log file here for the error info. Cache log file Sample error log: 2013/07/01 13:25:38| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:50| clientProcessRequest: Invalid Request 2013/07/01 13:26:05| tunnelConnectTimeout(): tunnelState->servers is NULL Some help can make our lives easier, Thanks in advance.

  Read the article

• Windows Vista claims wireless key is the wrong length

  - by humble coffee

  A family member of mine is house sitting and has been given the details of their wifi. The access point is an Airport Express, it has WEP encryption (I think) and they've been given a passphrase to use. I know it's a passphrase and not the encrypted key as it's an English word. The passphrase is 10 characters long. The problem is that Vista complains that it's not a valid key as it must be a 5 or 13 character non-hex key or a 10 or 26 character hex key. (From what I've read this suggests the encryption is WEP?) I've found a couple of suggested solutions, but I'm not actually at the house at the moment so I wanted to make sure I have a good chance of getting it to work when I'm there but have no internets to ask. Solution 1: Vista needs to be told explicitly what kind of encryption and key is being used. Specify in the connection settings that you are using WEP and that it is a "shared key". Solution2: Try converting the passphrase to hexadecimal using an ASCII-hex converter and entering that.

  Read the article

• Static Routes and the Routing Table

  - by TheD

  This is very much a learning question if someone would be happy to explain a couple of concepts. My question is - the default routing table that exists in, in my case, a default Windows 7 install, what do each of the routes in the table do? Here is a screenshot: The 10.128.4.0 is just a route I've added while messing. I understand from a question I posted on Superuser the first route is just a default route that will route all traffic for any IP to my default gateway on my Interface in use. But what about the others? And how would the routing table handle a machine with multiple NIC's, perhaps connected to two different networks, or maybe even two NIC's on the same network so a VM can have a physical Network card instead of each VM sharing the hosts. Thanks!

  Read the article

• Mac download speed keeps decreasing

  - by hatorade

  I have a Mac that is getting extremely low connection speed from my WiFi. The other 3 computers in this house have a fast connection. However, on this Mac, once I connect to WiFi it's fast, but as time goes on the speed decreases dramatically. I thought it was the browser or something (Safari) so I downloaded Firefox, but I have watched the download speed decrease consistently as time goes by and right now it's at 8kb/sec instead of the 60-200 range it started at. Any suggestions?

  Read the article

• Connect to MS Sql 2008 on local VM

  - by Campo

  I have a test machine. Server 2008 with Hyper V MSSQL 2008 Enterprise Lets call it MACHINE A on the VM it is as well Server 2008 with another MSSQL 2008 Ent Call it VM B I setup a DB on MACHINE A then backed it up and restored following the prepare database for mirroring instructions on MSDN onto VM B. I used to be able to connect to the VM B Instance from the main test server (MACHINE A) but now I cannot for some reason. It cannot seem to find the instance at all even when I browse network databases. I can ping the VM from any computer on the network and access its shares so I know it is discoverable. Just the end of a long day maybe I am missing something here.

  Read the article

• internet connection occasionally stops, but can still ping .com sites

  - by rj

  hi, every half hour or so, for 1-2 minutes my browser will stop navigating to sites, "waiting for ... to respond.." within 2 minutes i will be able to connect to sites and browse like normal again. weird thing is, while i cannot connect to sites, i get ping replies from any .com i type in. this happens on my home wireless network, using FF and IE on a win7 desktop AND FF on an ubuntu laptop the network is wpa2 secured, these are the only connections.

  Read the article

• What speed are Wi-Fi management and control frames sent at?

  - by Bryce Thomas

  There are a bunch of different 802.11 Wi-Fi standards, e.g. 802.11a, 802.11b, 802.11g, 802.11n etc. that all support different speeds. Wi-Fi frames are generally categorised as one of the following: Data frames - carry the actual application data Control frames - coordinate when its safe to send/reduce collisions Management frames - handle connection discovery/setup/tear down (e.g. AP discovery, association, disassociation) My question is about whether all these frames, and specifically management frames, are transmitted at the fastest supported speed available, or whether certain classes of frames are transmitted at some lowest common denominator speed. I have noticed that when I put an 802.11b/g only device into monitor mode and capture traffic over the air, I still see management frames (e.g. association/disassociation) being transmitted between my phone and AP which are both 802.11n, even though 802.11n has a higher transfer rate. So I am imagining one of two possibilities: My 802.11n phone/AP had to negotiate a slower speed for some reason and that's why I can see their frames on my 802.11b/g monitoring device. Management frames (and perhaps control frames also?) are sent at a lower speed, and it's only data frames that are transmitted faster with newer 802.11 standards. The reason I would like to know which one of these two possibilities (or perhaps a third possibility) is the case is that I want to capture management frames, and need to know whether using an 802.11b/g card is going to lead to me missing some frames sent at higher speeds than the monitoring card can observe. If management frames are indeed sent at a slower rate, then it's all good. If I just happen to be seeing the management frames because my phone/AP have negotiated a slower rate though, then I need to reconsider what card I use for packet capture.

  Read the article

• static routes, cisco ASA, remote locations

  - by Jeff

  192.168.3.1(ASA) - 192.168.2.1(ASA) - ( internet ) - 192.168.1.1(ASA) DomainController, FS, Exchange 192.168.0.1(ASA) - above is a rough idea what my network setup looks like. each internal ip (192.168.x.x) is located behind an ASA. Each location has a different gateway for the internet. They all talk to the 192.168.1.1 network for dns, dhcp, dc, exchange and so on. They can only see the 192.168.1.1, they can not see each other. In my Static Routes on my 192.168.1.1 ASA, should i have them configure as follows? example: 192.168.x.x 255.255.255.0 Locations_Internet_Gateway_IP OR 192.168.x.x 255.255.255.0 Main_Locations_Internet_Gateway_IP not sure which configurtation is correct, thanks in advance for any help!

  Read the article

• How are you supposed to NAT with Snow Leopard Server mini with only 1 ethernet port?

  - by erotsppa

  How are you supposed to NAT with Snow Leopard Server mini with only 1 ethernet port?

  Read the article

• Using "route add" to tell my computer to use a direct ethernet connexion instead of wifi ?

  - by TheSamFrom1984

  2 PCs are involved. Both are connected to the internet via Wifi on the same router. I can ping to/from each other and share folders flawlessly, but I'd like to be able to set a direct Ethernet link between them to speed up file transfers AND keep the Wifi connections (no gateway). So I plugged my RJ45 cable, and set up the connection. It works, but the PCs are only using this connection if one of them if disconnected from the Wifi. PC1 local address is 192.168.0.7 on its ethernet interface, and 192.168.1.21 on the wifi one. PC2 local address is 192.168.0.6 on its ethernet interface, and 192.168.1.22 on the wifi one. My question is : I'd like to using the route add command to tell PC1 to use the Ethernet interface when it needs to connect with PC2, by specifying "IF 2" at the end of the route add command. How can I do this ? I don't know what to put in the "gateway" parameter of the command, and everything I tried returns "the parameter is incorrect" (i don't know which one). ipconfig /all on PC1 : Windows IP Configuration Host Name . . . . . . . . . . . . : Sam-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : NETGEAR WG111v3 54Mbps Wireless USB 2.0 Adapter Physical Address. . . . . . . . . : 00-22-3F-DA-51-56 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::1d33:60b:476c:d396%12(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.1.21(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : vendredi 27 novembre 2009 15:38:48 Lease Expires . . . . . . . . . . : dimanche 29 novembre 2009 07:33:04 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DHCPv6 IAID . . . . . . . . . . . : 301998655 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-7E-58-EA-00-1A-4D-59-B2-71 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1A-4D-59-B2-71 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::f598:c3a0:df8d:706e%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 234887757 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-7E-58-EA-00-1A-4D-59-B2-71 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• Moving Farm to co-location hosting - network settings requirements

  - by Saariko

  I am moving my farm (2 Dell's R620) to a co-location hosting service. I am trying to figure out the secure way to have my network settings The requirements are: VM1 is the working HOST, includes: esxi 5.1, vSphere, 4 clients (w2008r2 all) VM2 has esxi 5.1 installed, and a single machine with Veeam Backup and copy 6.5 - keeping a copy of VM1 clients on the VM2 internal storage (this solution is due to a very small budget - in case of failure on Host 1 - can redirect IP's) Only 2 VM clients require network address and access from the WWAN - ISP provides IP's range for them (with Gateway and DNS) I need connection to the iDrac's from my office (option to create a VPN-SSL tunnel) Connection to the vSphere appliances I want to be able to RDP to the VM clients The current configuration is that each host has the iDrac dedicated nic connected , and another (NIC #1) connected - with a static IP on 192.168.3.x The iDrac's have a static IP from the same network range (19.168.3.x) It will look something like this: My thoughts: On NIC#2 of both hosts I will connected a crossed cable I will give each VM clients that needs internet access a 2ndry VM network with the assigned IP from the ISP open only to web - can not access from the My Question: Should I give IP's (external) to the machines who DO NOT require WWAN Access? - I can't see a way to RDP to them directly if not. Should I use the crossed cable? or just plug NIC #2 to the switch? Will this setup even work? What do I need to verify? What Virtual nic's and/or switches should I create on the Hosts?

  Read the article

• Can I map several physical interfaces to a single vmware vmnet interface?

  - by EricJLN

  I am using a rack mounted device that has 10 Ethernet ports built into it. For 8 of the ports, I would like to bind them to a single vwmare-server-2.0 virtual network interface, so that I can, in effect, use the ports as a hub for the external devices and internal virtual machines. How can I bridge a single vmware vmnet# interface to several physical interfaces?

  Read the article

• Configuring Ubuntu for Global SOCKS5 proxy

  - by x50

  Does anyone know the best way to configure Ubuntu to use a SOCKS5 proxy for all network traffic? Server is ubuntu server - all cli. So I cannot set via the Proxy Settings GUI. We want to push all outbound traffic through the proxy (apt-get, http, https, etc). I do need to separate ssh traffic so it stays locally. Everything else should hit the proxy server. not that it matters, but I'm using Squid for the proxy server. I know this is easy on Mac and Windows as you can set a proxy on the actual network interface. Can you do the same on Ubuntu?

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Monitoring Maximum Process Network Activity

  - by user125973

  We have a collocated server on which we run some OpenVZ hosts. Recently, we have had to pay a lot extra we keep exceeding our bandwidth quota. Our quota is 5 Mb/s but we have spike to almost 50. I looked at the graphs and there are some spikes happening at some intervals. I want to know which process is causing this so I need a tool that monitors the processes and gives me the one with the maximum instant traffic (It doesn't matter how much traffic we have as long as we don't exceed the 5Mb/s quota). Does anyone have a recommendation for this? My hosts are CentOS 5 with OpenVZ so I can see all the containter processes from the host, if that helps in any way.

  Read the article

• Does using a single cable to connect two switches create a bottleneck?

  - by Nick

  I realise this may be a stupid question for some, but it's something I've always wondered about. Let's say we have two gigabit switches and all of the devices on the network are also gigabit. If 10 computers connected to switch A need to transfer large amounts of data to a server on Switch B (at the same time), is the maximum transfer speed of each connection limited by the bandwidth of the connection between the two switches? In other words, would each computer only be able to transfer at a speed of one gigabit divided by the 10 machines trying to use the "bridge" between switches? If so, are there any workarounds so that every device can use it's maximum speed from point to point?

  Read the article

• Bonding: works only from one link

  - by Crazy_Bash

  I would like to install bonding with 4 links. but only one of them is active. eth4 is always active. the others simply don't work. those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >