Search Results

Search found 5123 results on 205 pages for 'gateway timeout'.

Page 150/205 | < Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• Persistent static route stops working after VPN drops and reconnects

  - by user76157

  I've got a VPN between two networks, one home and one office (A and B). Their subnets are: (A) 192.168.1.0 and (B) 192.168.0.0 The two networks have identical ADSL routers. Unfortunately these can only do dial-out VPN. So I've got a Windows 2008 server on Network B acting as a VPN server (ServerB). Network A's router (RouterA) passes through Network B's router and connects via PPTP to ServerB. RouterA is assigned the static IP 192.168.0.40 on Network B. There's a persistent static route on ServerB telling it to use 0.40 for all requests to Network A's subnet, 192.168.1.0. (route -p add 192.168.1.0 mask 255.255.255.0 192.168.0.40). This enables ServerB to ping all machines on A (and those machines to ping ServerB). The VPN connection occasionally drops (I'm not sure why - it's set to remain always on and seems to drop randomly). This wouldn't be too much of a problem, as it reconnects automatically and quickly, except that when it does reconnect, the static route on ServerB no longer works. Route print (on ServerB) shows that the persistent static route still exists. However a tracert to a machine on Network A doesn't use the static route; it tries instead to use ServerB's default gateway (which is RouterB), and fails to find the machine. Deleting and re-adding the static route fixes the problem - a tracert uses the static route. At the moment, a batch file to delete and re-add the static route is scheduled to run every day. But this is clearly far from an ideal solution! I hope that's not too confusing. Any help would be very much appreciated.

  Read the article

• Backing up SQL NetApp Snapshots using TSM

  - by WerkkreW

  In our environment we have a 3 node SQL 2005 Cluster which is on NetApp storage. We are currently using SMSQL (NetApp SnapManager for SQL) to take Snapshot backups of the data. This works great, but due to some audit requirements we are also forced to maintain some copies on tape. We have used NDMP in other places across the enterprise but we do not want to use it in this specific instance. Basically what I need to do is, get the most recent snapshot copy of the databases on tape, via Tivoli Storage Manager (TSM). What I have done is, obtained a basic Windows Server 2003 VM with SnapDrive installed, which is SAN attached and zoned to the NetApp, and I have written a batch file to do the following: Mount the latest __RECENT snapshot lun to the host, using a specific drive letter Perform a TSM based incremental backup Dis-mount the LUN This seems to work fine, except sometimes the LUN's do not mount due to some sort of timeout. Also, due to my limited knowledge of windows batch scripting, I have no way to monitor the success or failure of these backups since I do not know how to send a valid return code back to the TSM scheduling service. Is there a more efficient/elegant way to accomplish this without NDMP?

  Read the article

• Redmine install not working and displaying directory contents - Ubuntu 10.04

  - by Casey Flynn

  I've gone through the steps to set up and install the redmine project tracking web app on my VPS with Apache2 but I'm running into a situation where instead of displaying the redmine app, I just see the directory contents: Does anyone know what could be the problem? I'm not sure what other files might be of use to diagnose what's going on. Thanks! # # Based upon the NCSA server configuration files originally by Rob McCool. # # This is the main Apache server configuration file. It contains the # configuration directives that give the server its instructions. # See http://httpd.apache.org/docs/2.2/ for detailed information about # the directives. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # The configuration directives are grouped into three basic sections: # 1. Directives that control the operation of the Apache server process as a # whole (the 'global environment'). # 2. Directives that define the parameters of the 'main' or 'default' server, # which responds to requests that aren't handled by a virtual host. # These directives also provide default values for the settings # of all virtual hosts. # 3. Settings for virtual hosts, which allow Web requests to be sent to # different IP addresses or hostnames and have them handled by the # same Apache server process. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "/var/log/apache2/foo.log" # with ServerRoot set to "" will be interpreted by the # server as "//var/log/apache2/foo.log". # ### Section 1: Global Environment # # The directives in this section affect the overall operation of Apache, # such as the number of concurrent requests it can handle or where it # can find its configuration files. # # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # NOTE! If you intend to place this on an NFS (or otherwise network) # mounted filesystem then please read the LockFile documentation (available # at <URL:http://httpd.apache.org/docs-2.1/mod/mpm_common.html#lockfile>); # you will save yourself a lot of trouble. # # Do NOT add a slash at the end of the directory path. # ServerRoot "/etc/apache2" # # The accept serialization lock file MUST BE STORED ON A LOCAL DISK. # #<IfModule !mpm_winnt.c> #<IfModule !mpm_netware.c> LockFile /var/lock/apache2/accept.lock #</IfModule> #</IfModule> # # PidFile: The file in which the server should record its process # identification number when it starts. # This needs to be set in /etc/apache2/envvars # PidFile ${APACHE_PID_FILE} # # Timeout: The number of seconds before receives and sends time out. # Timeout 300 # # KeepAlive: Whether or not to allow persistent connections (more than # one request per connection). Set to "Off" to deactivate. # KeepAlive On # # MaxKeepAliveRequests: The maximum number of requests to allow # during a persistent connection. Set to 0 to allow an unlimited amount. # We recommend you leave this number high, for maximum performance. # MaxKeepAliveRequests 100 # # KeepAliveTimeout: Number of seconds to wait for the next request from the # same client on the same connection. # KeepAliveTimeout 15 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # event MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_event_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog /var/log/apache2/error.log # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn # Include module configuration: Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf # Include all the user configurations: Include /etc/apache2/httpd.conf # Include ports listing Include /etc/apache2/ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # # Define an access log for VirtualHosts that don't define their own logfile CustomLog /var/log/apache2/other_vhosts_access.log vhost_combined # Include of directories ignores editors' and dpkg's backup files, # see README.Debian for details. # Include generic snippets of statements Include /etc/apache2/conf.d/ # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ # Enable fastcgi for .fcgi files # (If you're using a distro package for mod_fcgi, something like # this is probably already present) #<IfModule mod_fcgid.c> # AddHandler fastcgi-script .fcgi # FastCgiIpcDir /var/lib/apache2/fastcgi #</IfModule> LoadModule fcgid_module /usr/lib/apache2/modules/mod_fcgid.so LoadModule passenger_module /var/lib/gems/1.8/gems/passenger-3.0.7/ext/apache2/mod_passenger.so PassengerRoot /var/lib/gems/1.8/gems/passenger-3.0.7 PassengerRuby /usr/bin/ruby1.8 ServerName demo and my vhosts file #No DNS server, default ip address v-host #domain: none #public: /home/casey/public_html/app/ <VirtualHost *:80> ServerAdmin webmaster@localhost # ScriptAlias /redmine /home/casey/public_html/app/redmine/dispatch.fcgi DirectoryIndex index.html DocumentRoot /home/casey/public_html/app/public <Directory "/home/casey/trac/htdocs"> Order allow,deny Allow from all </Directory> <Directory /var/www/redmine> RailsBaseURI /redmine PassengerResolveSymlinksInDocumentRoot on </Directory> # <Directory /> # Options FollowSymLinks # AllowOverride None # </Directory> # <Directory /var/www/> # Options Indexes FollowSymLinks MultiViews # AllowOverride None # Order allow,deny # allow from all # </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /home/casey/public_html/app/log/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel debug CustomLog /home/casey/public_html/app/log/access.log combined # Alias /doc/ "/usr/share/doc/" # <Directory "/usr/share/doc/"> # Options Indexes MultiViews FollowSymLinks # AllowOverride None # Order deny,allow # Deny from all # Allow from 127.0.0.0/255.0.0.0 ::1/128 # </Directory> </VirtualHost>

  Read the article

• upstart config to start sync daemon as non-root user

  - by Rudiger Wolf

  I am planning to use inosync to sync data from master server to several client servers. I have created a user called rsyncuser in both master and slaves with access permissions and passwordless ssh access from master to slave servers. Inosync is working when I use it from the command line as rsyncuser. Next I want this to start automatically when server is turned on. I figured upstart is the way to get this working. I am unable to find the right upstart command to get this working. Here is my upstart conf file. The problem seems to be around running "inosync -d -c /etc/inosync/inosync_rsyncuser.py" as a given user. As you can see I have tried a number of various options! description "start inosync to sync data to other CDN Servers as rsyncuser" console output #start on startup #stop on shutdown start on (net-device-up and local-filesystems) stop on runlevel [016] #start on runlevel [2345] #stop on runlevel [!2345] #kill timeout 30 env RUN_AS_USER=rsyncuser expect fork script echo "Inosync updtart job seems to have started" /tmp/upstart.log # exec sudo -u rsyncuser -c "ls -la" /tmp/upstart.log 2&1 # LOGFILE=/var/log/logfile.`date +%Y-%m-%d`.log # exec su - $RUN_AS_USER -c "inosync -d -c /etc/inosync/inosync_rsyncuser.py" $LOGFILE 2&1 # exec su -c "ls -la" /tmp/upstart.log 2&1 # emit inosync_running end script

  Read the article

• Server taking too long to respond error

  - by DCJones

  This is my first post on serverFault and my first entry in to web server configuration. The hardware and software. CPU: GenuineIntel, Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz OS: Linux 2.6.18-128.el5 Memory: 2Gb Background. I am running a small database (MySQL), around 1000 records with each record containing 44 fields. At the start of each day “00:01” the tables are cleared and populated with fresh data. The are 10 remote PCs all running Winodws XP and Firefox internet browser. All remote PC’s are connected to the internet using a min 4Gb broadband connection. Each remote PC runs a URL which displays a dynamic page of data which is refreshed every 20 seconds. This is a continual process 24 hours a day. I problem I am having is on odd occasions throughout the day the PC browser error with “Server taking too long to respond error”. What I am trying to find our is if I have the correct setting in the httpd.conf file on the server. Any help or advice anyone can provide would be very helpful. Best regards Dereck Server config file: httpd.conf ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 5 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 254 MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule>

  Read the article

• Basic IP address structure

  - by dannymcc

  We currently have a few servers, around 30-40 workstations and 16 phones. Each device has a static IP address. As an example the standard settings for a new workstation is; IP: 192.168.1.XXX Subnet: 255.255.255.0 Gateway: 192.168.1.99 DNS: 192.168.1.50 As I am slowly exploring new server OS's and virtualisation etc. I am getting close to wanting a wider range of IP addresses. What I would like to do is seperate the devices by IP as follows: Servers 192.168.1.XXX Workstations 192.168.2.XXX Printers 192.168.3.XXX Phones 192.168.4.XXX VM's 192.168.5.XXX Is this a bad idea, or is this a common way of doing things? My biggest concern is the phones and subnet masks. The phones are managed by our provider although I have access to the server that runs them. Would I need to change the subnet mask to 255.255.0.0 on all devices? Or only those that change? For example, the phones don't need to connect to any other devices other than other phones and the phone server. So if I have the phones on 192.168.1.XXX with a subnet mask of 255.255.255.0 and then moved everything I had complete ownership/control of to 192.168.X.XXX with a new subnet mask of 255.255.0.0. Would that work?

  Read the article

• iSCSI, failover and XenServer

  - by jemmille

  I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid&gt; is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

  Read the article

• Solaris TCP stack tuning

  - by disserman

  We have a large web project (about 2-3k requests per second), using haproxy (http://haproxy.1wt.eu/) as a frontend and load balancer between the java application servers. The frontend (haproxy) is running on Linux but we are going to migrate it to the Solaris 10 as all our other servers are running under Solaris. After switching a traffic I see the two things: a) the web site became loading slower (5-10 seconds with images in comparison to 2-3 seconds on Linux) b) sometimes haproxy fails to perform a "lifecheck" (get a special web page and analyze http response code) due to the socket timeout. After switching traffic back to Linux everything is okay. I've tried to tune all params I found in /dev/tcp but no progress. I believe the problem is in some open socket limitations. If someone can point me to the answer, I would be greatly appreciated. p.s. haproxy is running under Xen DomU on Linux (Kernel 2.6.18, Debian 5), under zone on Solaris (10 u8). the only thing we did on Linux is increasing of ip_conntrack_max (I believe Solaris option tcp_conn_req_max_q is the equivalent).

  Read the article

• How to remove request blocking on apache reverse proxy after failure of backend before asking backen

  - by matnagel

  I am working on an apache2 reverse proxy vhost. When the server behind apache is down, the first request to apache shows the error page of course. But at subsequent requests it seems apache delays for some time before asking the backend server again. During all this time (which is short but in development I don't want a delay at all) only the apache error page is shown to the browser, although the backend server is already up. Where is this setting in apache, what is this behaviour, and how can I set the delay time to zero? Edit: I am not trying to change the timeout for a single request. I want to change the blocking time. It is my experience that apache blocks further requests for a certain time before asking a backend server again that has failed once. Edit2: This is what apache delivers: Service Temporarily Unavailable The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later. Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.7 with Suhosin-Patch proxy_html/3.0.0 Server at localhost Port 80 After hitting Ctrl-R in firefox for 60 seconds the page finally appears.

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• Intermittent "Lost connection to MySQL server at 'reading initial communication packet'"

  - by db2

  Our web environment consists of two servers. Web front-end. Dell PowerEdge R610, RHEL 5.5, Apache 2.2.17, php 5.2.14. Database server. Dell PowerEdge R710, Windows 2008 R2 Standard x64, MySQL 5.5.11-log x64. Normally these two work perfectly fine together. However, when I try to get them talking via a dedicated LAN on their secondary NICs (each machine has four of them), things get flaky. I have NIC #2 on both machines configured on the 172.16.1.0/24 subnet, with no gateway or DNS servers (obviously, since it's just those two systems), and I put the private IP address of each machine into the hosts file of the other. The routing tables on both machines look okay after I do this. I've tried this with both a crossover cable draped directly between the two NICs, and also via a dedicated vlan on the switch in the rack. In either case, I get intermittent connection problems. It's a fairly small percentage of connections that fail, but it's enough to cause a significant problem, and I have to switch back to the main network connection, which will contend with all the other traffic and hosts on the switch. The full error message that appears in the application log: SQLSTATE[HY000] [2013] Lost connection to MySQL server at 'reading initial communication packet', system error: 110 Am I doing something really dumb that's causing this to not work properly? Anything I can check in MySQL that would explain why it's failing to connect occasionally?

  Read the article

• Can't Connect To Local Mysql Using IP Address, but CAN connect from remote server

  - by user1782041

  Here's an interesting one that does not seem to fall into any of the mysql connection issues I've read about or searched for: On an Ubuntu 12.04 box I had some system updates waiting to install, and I took care of that this evening. After the install, I started seeing some errors in my syslog complaining about a particular php script that could no longer connect to the mysql instance on the box. Here is the specific error: PHP Warning: mysql_connect(): Can't connect to MySQL server on '192.168.0.40' (4) Now, the server's IP address is 192.168.0.40, and I've checked to make sure that I have mysql listening on 0.0.0.0 so that I can connect using either "localhost" or "192.168.0.40". Here's where things get odd: From the local machine, if I try the following: mysql -uroot -p -h192.168.0.40 I get this error: ERROR 2003 (HY000): Can't connect to MySQL server on '192.168.0.40' (110) I've checked, and error 110 indicates an OS timeout, and error 2003 is the mysql generic "can't connect" error. This indicates that it is not permissions with the user. However, if I do the same thing from a remote machine (say, from 192.168.0.30), I log right in with no problems. Futher, other scripts on the local machine that connect to mysql using "localhost" for the host rather than "192.168.0.40" connect with no problems. Also, I can connect via the mysql socket with no problems both from the command line and php scripts. So, this feels like a networking issue of some kind on the local box, but there are no iptables rules on this box (it is firewalled externally) and I can't figure out what else may be causing this. This problematic script worked perfectly prior to the latest system update. For now, I'll simply change the script to connect via localhost, but I'd really like to know why it broke for 2 reasons: There may be other scripts that connect using 192.168.0.40 that don't run very often which are now broken. Auditing them all will take more time than I feel like devoting at the moment. I'm curious, and want to know why it broke so I can fix it correctly. Any help?

  Read the article

• How to force certain traffic through GRE tunnel?

  - by wew

  Here's what I do. Server (public internet is 222.x.x.x): echo 'net.ipv4.ip_forward=1' >> /etc/sysctl.conf sysctl -p iptunnel add gre1 mode gre local 222.x.x.x remote 115.x.x.x ttl 255 ip add add 192.168.168.1/30 dev gre1 ip link set gre1 up iptables -t nat -A POSTROUTING -s 192.168.168.0/30 -j SNAT --to-source 222.x.x.x iptables -t nat -A PREROUTING -d 222.x.x.x -j DNAT --to-destination 192.168.168.2 Client (public internet is 115.x.x.x): iptunnel add gre1 mode gre local 115.x.x.x remote 222.x.x.x ttl 255 ip add add 192.168.168.2/30 dev gre1 ip link set gre1 up echo '100 tunnel' >> /etc/iproute2/rt_tables ip rule add from 192.168.168.0/30 table tunnel ip route add default via 192.168.168.1 table tunnel Until here, all seems going right. But then 1st question, how to use GRE tunnel as a default route? Client computer is still using 115.x.x.x interface as default. 2nd question, how to force only ICMP traffic to go through tunnel, and everything else go default interface? I try doing this in client computer: ip rule add fwmark 200 table tunnel iptables -t mangle -A OUTPUT -p udp -j MARK --set-mark 200 But after doing this, my ping program will timeout (if I not doing 2 command above, and using ping -I gre1 ip instead, it will works). Later I want to do something else also, like only UDP port 53 through tunnel, etc. 3rd question, in client computer, I force one mysql program to listen on gre1 interface 192.168.168.2. In client computer, there's also one more public interface (IP 114.x.x.x)... How to forward traffic properly using iptables and route so mysql also respond a request coming from this 114.x.x.x public interface?

  Read the article

• Configuring vsftpd with nginx on Ubuntu 12.04 LTS

  - by arby

  I've attempted to configure a nginx / vsftpd server on Ubuntu 12.04 LTS (via amazon ec2) a couple times now, but I seem to keep making a mistake along the way. Currently, when I try to connect to my ftp server it takes a minute or so before it connects. Then when I issue a command, they all timeout with an operation failed error. Aside from these issues, I'm not completely confident with the file ownership & permissions or the configuration / settings. So, I think it's best if I just re-install and re-configure correctly. I believe the nginx installation comes with a default user of www-data:www-data and web root directory ownership by root:root. Vsftpd, however, needs to have a user created with the same group as the nginx user (www-data), and the same home directory as the nginx server (/usr/share/nginx/www), with g+w chmod permissions granted on that directory. The vsftpd.conf file should disable anonymous logins and enable local logins, file writing, and chroot local users. In my previous config, I had /bin/false set for the ftp user's shell and pam_shells.so disabled. I also had local_umask set to 0027. So, starting with a fresh ec2 instance, I've got: sudo apt-get install vsftpd sudo apt-get install nginx For the firewall I issued the command (not sure if necessary): sudo ufw allow ftp Which commands / config is recommended from here? I only need 1 ftp user that I can use to login with my ftp client to modify the single nginx web domain, which will need php & sql for WordPress.

  Read the article

• Ubuntu 12.04 - Pound Reverse Proxy and Adobe Flex/Flash Auth

  - by James

  First time posting, I have a completely fresh install of ubuntu 12.04 Client as a reverse proxy gateway to our internal network. Our setup is we have one external ip but three domains we would like to point to various webservers on our internal network. It's not so much a load balancing issue or cacheing etc. Merely routing some Client browsers to a port 80 webpage (to adhere to some stricter corporate policies regarding placing port numbers after domain names). I have gone with pound and everything seems to be working fine. Static pages load etc. Everything is good with the exception of a Flash/Flex based WebClient for a Digital Asset Management program. The actual static page loads fine, it is just at the moment of entering credentials, be they correct or incorrect, and hitting login, there is no response whatsoever. Either a rejection or confirmation etc. So the request back to the internal server can't be getting through. I have googled extensively and there might be a solution in a crossdomain.xml file? Documentation isn't very clear. And we are not the authors of the DAM app, and have no control over the code on the Flash/Flex side. Questions: Is there a particular config file/solution for pound that allows Flash/Flex auth information to be forwarded? Is there another reverse proxy program (nginx?)that allows this type of config? Am I looking at this the entire wrong way, should Flash/Flex fundamentally not be allowed to have this access?

  Read the article

• Missing Home Folder XP Clients 2008R2 Domain

  - by minamhere

  We just completed a migration from Server 2003 to Server 2008R2. Everything seems to have gone well except that many of our desktops have stopped mapping the Home Folder as set in Active Directory. Other mappings that are defined on individual clients are mapping just fine, these mappings are all on the same file server as the failing Home Folders. Half of the users are on 1 file server and half are on another. Users from both servers are having this problem. I have enabled the Group Policy setting to "Wait for network before logging in". I enabled the policy to "Run Logon Scripts synchronously". There are no errors on the Domain Controller or either File Server. When I enabled Group Policy Preferences as an attempted workaround, I get this error: The user 'V:' preference item in the '<Policy Name>' Group Policy object did not apply because it failed with error code '0x800708ca This network connection does not exist.' This error was suppressed. This seems to indicate that the network connection is not ready by the time Group Policy is processed. But isn't this the point of the "Wait before logging in" and "Run Logon scripts synchronously" settings? Some other background facts: The new Server 2008R2 installation is a Virtual Machine. It is on a new Subnet in a different building from the old server. DNS and DHCP were also migrated from the old DC to this new DC. These Home Folders were all working properly before the migration. Are there new security restrictions/policies in Server 2008R2 that might be causing this? Is there a way to check whether I have an underlying network connectivity issue? Maybe moving the server to the new building is causing a delay/timeout? Any thoughts or ideas on what could be causing this or how I can resolve this? Thanks.

  Read the article

• How do I tell ubuntu to send traffic to a single IP through eth6?

  - by flashnode

  I want to ensure that all IP traffic going to 172.16.60.62 uses eth6. Please provide complete commands because my linux-fu is rusty. The host is running Ubuntu Precise 12.04 user@host:~$ ifconfig eth3 eth3 Link encap:Ethernet HWaddr 00:e0:81:72:fe:c9 inet addr:172.16.60.122 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe72:fec9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:128500 errors:0 dropped:0 overruns:0 frame:0 TX packets:29082 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67524823 (67.5 MB) TX bytes:2217634 (2.2 MB) Interrupt:71 Base address:0x6000 user@host:~$ ifconfig eth6 eth6 Link encap:Ethernet HWaddr 00:60:dd:47:81:35 inet addr:172.16.60.61 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:8135/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:109610 errors:0 dropped:0 overruns:0 frame:0 TX packets:109388 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10785630 (10.7 MB) TX bytes:10754350 (10.7 MB) Interrupt:70 user@host:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.60.1 0.0.0.0 UG 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth3

  Read the article

• Migrating Windows XP BOOT.INI Settings to Windows 7 Boot-loader

  - by Synetech inc.

  Hi, Two months ago my motherboard died, so I bought a used computer that came with Windows 7. I have since installed my old hard-drive, which had Windows XP on it, in this system. What I am trying to do now is to figure out a way to migrate the settings from XP's BOOT.INI into 7's boot-loader. Below is the BOOT.INI I used in XP (I have reduced the strings and updated the disks to point to the new location of the old HD. Oh and I am not clear on the drive letters. In XP, I could boot the recovery console or MS-DOS from a file in C:\ that contains the boot-sector. I am not sure what drive letter it would be called now—I had to manually change all the drive letters of the old partitions in Windows 7 because it auto-assigned them all wrong/differently). [boot loader] timeout=10 default=multi(0)disk(0)rdisk(1)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP" /fastdetect multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP (Safe)" /safeboot:network /sos /bootlog /noguiboot C:\CMDCONS\BOOTSECT.DAT="Recovery Console" /cmdcons C:\BOOTSECT.DOS="MS-DOS 7.10" /win95 I have looked around, and have only been able to find some bcdedit commands to add XP to the boot-loader, but none that include information on setting safe-mode for it (or changing any of the XP load options for that matter). Not surprisingly I suppose, I have not found anything on adding the XP recovery console or DOS to the Windows 7 boot-loader. (Yes, I tried EasyBCD, but that did not help; it had no options for XP, and the best I managed was to get a choice of booting 7 or normal-mode XP—choosing XP didn't even give the old XP boot menu.) Can anyone please tell me how to export the entries in XP's boot.ini to 7's boot-loader so that on boot, I can choose to load the following: Windows 7 Windows 7 (Safe-mode) (Windows 7 (The Win7 counterpart of the Recovery Console)) Windows XP Windows XP (Safe-mode) Windows XP (Recovery Console) MS-DOS 7.10

  Read the article

• How to setup equivalent USVIDEO.ORG DNS-Proxy on Linux

  - by Gary

  I have a VPS in the USA running Ubuntu. I want to setup something similar to http://www.usvideo.org Basically, USVIDEO is a DNS service that allows Canadians to access American content like Hulu, Netflix, NBC, and etc (restricted by geographical IP). Here is how I think USVideo does it: Clients (PS3, XBOX, PC) specifies the DNS server(s) as specified on USVIDEO.org's website. If the DNS request is a video/audio site such as Netflix or Pandora, forward the request to a proxy. Otherwise, for all other requests, forward it to a different DNS server. If the specific video/audio URL is requested, return the address of the proxy server, which in turn relays traffic to the destination video/audio domain via the U.S. gateway so that it appears that the access is coming from a U.S. IP address. Once the DNS request has passed the U.S. IP address check, their proxy server steps out of the loop and lets the video streaming site contact you directly to start the video stream. This trick relies on the way that the video streaming sites check the country of your IP address once up front, but don't actually check the country of the destination IP address while the video is streaming. What is elegant about this solution is that a VPN Tunnel is not required to bypass geographical IP checks from certain websites. All that is required on the client side is to specify the DNS server (the VPS). If a certain site is geographically locked, just forward the traffic to a proxy, and that's it. These sites can be specified in the DNS entries, or perhaps in the proxy service to redirect the DNS request to its own proxy. I believe what I need to setup something similar is Squid Proxy, IPTables, and DNS. What I need help is how to exactly approach this? Would Squid Proxy be setup as a transparent proxy?

  Read the article

• Slow upload speeds with pfsense virtual appliance

  - by Justin Shin

  I have a pfSense virtual appliance set up in front of a Windows server. The pfSense appliance has been configured with two L2L IPSec VPN sites and not too much else. The appliance has two vNics which both exist on the same VLAN, but one is "WAN" and the other is "LAN." When I run speedtest.net on my Windows server when I have configured it to use a static WAN address and gateway, I get great speeds - maybe around 50 down, 15 up. However, when I configure it with a private IP address, I get similar download speeds but terrible upload speeds - around 2 or 3 Mbps consistently. I used Wireshark to see what gives but there didn't appear to be too much helpful information there, or I just could not find it. Besides the L2L VPNs, other configurations include: Automatic Outbound NAT Virtual P-ARP IP for the Windows Server WAN Firewall rule to allow * to * on RDP WAN Firewall rule to allow * to * (enabled this just for testing... didn't help!) No DHCP or any other services besides IPSec VPN No Errors LAN or WAN No collisions LAN or WAN I would be happy to post the full config file if it would help. I've been scratching my head at this one all day!

  Read the article

• Rebooting access point via SSH with pexpect... hangs. Any ideas?

  - by MiniQuark

  When I want to reboot my D-Link DWL-3200-AP access point from my bash shell, I connect to the AP using ssh and I just type reboot in the CLI interface. After about 30 seconds, the AP is rebooted: # ssh [email protected] [email protected]'s password: ******** Welcome to Wireless SSH Console!! ['help' or '?' to see commands] Wireless Driver Rev 4.0.0.167 D-Link Access Point wlan1 -> reboot Sound's great? Well unfortunately the ssh client process never exits, for some reason (maybe the AP kills the ssh server a bit too fast, I don't know). My ssh client process is completely blocked (even if I wait for several minutes, nothing happens). I always have to wait for the AP to reboot, then open another shell, find the ssh client process ID (using ps aux | grep ssh) then kill the ssh process using kill <pid>. That's quite annoying. So I decided to write a python script to reboot the AP. The script connects to the AP's CLI interface via ssh, using python-pexpect, and it tries to launch the "reboot" command. Here's what the script looks like: #!/usr/bin/python # usage: python reboot_ap.py {host} {user} {password} import pexpect import sys import time command = "ssh %(user)s@%(host)s"%{"user":sys.argv[2], "host":sys.argv[1]} session = pexpect.spawn(command, timeout=30) # start ssh process response = session.expect(r"password:") # wait for password prompt session.sendline(sys.argv[3]) # send password session.expect(" -> ") # wait for D-Link CLI prompt session.sendline("reboot") # send the reboot command time.sleep(60) # make sure the reboot has time to actually take place session.close(force=True) # kill the ssh process The script connects properly to the AP (I tried running some other commands than reboot, they work fine), it sends the reboot command, waits for one minute, then kills the ssh process. The problem is: this time, the AP never reboots! I have no idea why. Any solution, anyone?

  Read the article

• o2cb thinks ocfs2 cluster is still online, and refuses to shut down

  - by Kendall

  I have a handful of OpenSuSE 11.2 servers that utilize OCFS2 volumes. I've noticed that o2cb can't figure out when the OCFS2 cluster is actually mounted. For example, when I try to shutdown o2cb, after stopping OCSF2, o2cb refuses to shutdown because it thinks OCFS2 is still up! After stopping OCFS2 I try to stop o2cb... hamguy:/dev/disk/by-label # /etc/init.d/o2cb stop Stopping O2CB cluster ocfs2: Failed Unable to stop cluster as heartbeat region still active So I check the status... hamguy:/dev/disk/by-label # /etc/init.d/o2cb status Driver for "configfs": Loaded Filesystem "configfs": Mounted Stack glue driver: Loaded Stack plugin "o2cb": Loaded Driver for "ocfs2_dlmfs": Loaded Filesystem "ocfs2_dlmfs": Mounted Checking O2CB cluster ocfs2: Online Heartbeat dead threshold = 31 Network idle timeout: 30000 Network keepalive delay: 2000 Network reconnect delay: 2000 Checking O2CB heartbeat: Active And double check OCFS2... hamguy:/dev/disk/by-label # /etc/init.d/ocfs2 status Configured OCFS2 mountpoints: /u/conf /u/logs /u/backup /u/client /u/data /u/mdata OCFS2 is clearly down, while o2cb clearly thinks otherwise. The versions of OCFS2 and o2cb are... kendall@hamguy:~> rpm -qa |grep ocfs2 ocfs2console-1.4.1-25.6.x86_64 ocfs2-tools-o2cb-1.4.1-25.6.x86_64 ocfs2-tools-1.4.1-25.6.x86_64 kendall@hamguy:~> rpm -qa |grep o2cb ocfs2-tools-o2cb-1.4.1-25.6.x86_64 What causes this, and is there a way around it? If I try to reboot the machine, it will just sit there forever until your physically power cycle it. That obviously is a bit of a problem. Any insight is appreciated, thank you. Kendall

  Read the article

• Apache mod_rewrite and mod_vhost_alias Virtual Hosts and %1

  - by Matt Wall

  I have put the main bits of my httpd.conf down below. I am using %1 to get the host field so I can dynamically add vhosts by just creating dns/folders. One problem is I need to reference this: HttpStreamingLiveEventPath "D:/FMSApps/%1" HttpStreamingContentPath "D:/FMSApps/%1" In Apache when I try say to do this: http://test.domain.com/hds-vod/myfile.mp4.f4m it sees the %1 in the logs, and fails. Apache gives me this: [error] mod_jithttp [403]: No access to D:/Content/%1/DefaultContent/eve.mp4 What I'm looking for is the D:/Content/%1/DefaultContent/eve.mp4 to become D:/Content/test/DefaultContent/eve.mp4 Anyone have any useful resources / hints etc. to help me? Meanwhile my Google searching continues...! Listen 80 ServerName main1.rtmphost.com AccessFileName .htaccess ServerSignature On UseCanonicalName Off HostnameLookups Off Timeout 120 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 15 RewriteLogLevel 0 RewriteLog logs/rewrite.log DocumentRoot D:/Content LoadModule vhost_alias_module modules/mod_vhost_alias.so VirtualDocumentRoot "D:/Content/%1" RewriteEngine On <Directory /> Options None AllowOverride None Order allow,deny Allow from all Satisfy all </Directory> <IfModule f4fhttp_module> <Location /vod> HttpStreamingEnabled true HttpStreamingContentPath "D:/FMSApps/%1" Options FollowSymLinks </Location> Redirect 301 /live/events/livepkgr/events /hds-live/livepkgr <Location /hds-live> HttpStreamingEnabled true HttpStreamingLiveEventPath "D:/FMSApps/%1" HttpStreamingContentPath "D:/FMSApps/%1" HttpStreamingF4MMaxAge 2 HttpStreamingBootstrapMaxAge 2 HttpStreamingFragMaxAge -1 Options FollowSymLinks </Location> </IfModule>

  Read the article

• django, mod_wsgi, MySQL High CPU - Problems

  - by Red Rover

  Good Evening, and thank you for reading this post. I am having a problem with Django after migrating the dB from SQLlite to MySQL. Initially, for the first 48hours, all ran well. But now we are experiencing high cpu about every 30 minutes. This is a production ESX4i VM host, with 2 x 2.8 ghz CPUs and 12 GB ram. I have allocated 4 cpu's to this VM and 4 GB memory. Any insight into this configuration and help with the spikes in CPU would be appreciated. IT is configured to use the prefork MPM. Outlined are the config's for the different services: MySQL Server version: 5.1.61 Source distribution Django 1.3 mod_wsgi Apache/2.2.15 httpd.conf Timeout 120 KeepAlive Off MaxKeepAliveRequests 400 KeepAliveTimeout 3 prefork MPM StartServers 8 MinSpareServers 8 MaxSpareServers 16 ServerLimit 40 MaxClients 40 MaxRequestsPerChild 0 worker MPM StartServers 16 MaxClients 1024 MinSpareThreads 64 MaxSpareThreads 256 ThreadsPerChild 64 MaxRequestsPerChild 10240 MySQL my.conf [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql symbolic-links=0 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid my.cnf wsgi.conf LoadModule wsgi_module modules/mod_wsgi.so /etc/httpd/conf.d/wsgi.conf WSGISocketPrefix /var/run/wsgi WSGIPythonEggs /var/tmp WSGIDaemonProcess SITE maximum-requests=10000 WSGIProcessGroup SITE

  Read the article

< Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >