Search Results

Search found 10391 results on 416 pages for 'sys dm exec requests'.

Page 154/416 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• DBAN Hangs at PCI (sysfs)

  - by David

  I'm running Derik's Boot and Nuke 2.2.6 (beta). When I get to a blue screen(Not BSOD) the following is printed. Derik's Boot and Nuke 2.2.6 (beta) is starting. Waiting for USB devices to register..........................done. PCI (sys) After that, it just sits there forever... Any advice, other than an older version of DBAN? I have gotten this version of DBAN to work on an older machine before.

  Read the article

• Profiles and using the local profile for a domain user

  - by Harry

  I’m having some trouble with profiles and would like to reach out for some help. I’ve tried to do some research to help myself along, but I’m not making much progress on my own. I’ve pretty much taken over the sys admin duties for my small lab, I don’t have much experience to justify it besides I’m the only with the time and dedication to go at it (The environment was in a state of disrepair). My network and domain I look over are extremely small by most standards, about 10 users at a time. They are pretty intensive activity on the network, and we do work with fairly large files. None of the network is online, which is nice at the moment because it allows me not to have another headache. On to my profile problem, I have set up roaming profiles for the users in the network. Now after a little research, I think I will be switching this to a hybrid of folder redirection and roaming profiles as this seems to best practice. I also don’t want the users having to wait for a long time if they have a bloated profile. Now I’ve finally got a build working using MDT. We have Mac Pros, and it wasn’t fun getting everything to play nice. The way I did this was by setting up a reference computer and installing all the software and tools that each user would need and editing the settings preferences to how we would need them. I think used MDT to do a sys prep and capture to create the image of my reference computer. Using the reference image I can push out my images to the rest of the desktops in my environment. The issue I’m having is when we join the computer to domain. The user can login and operate fine on the computer, but I’d like a more. When the user is logged on with their domain user name they lose a lot of the icons I had on my reference image, as well as the desktop background and some other miscellaneous settings. I would love to have the user log on using their domain user name and see the icons and desktop environment as I had it setup on the reference computer. I’m not sure if it is possible, or something simple that I’m missing, but any help would be greatly appreciated!

  Read the article

• socat and rich terminals (with Ctrl+C/Ctrl+Z/Ctrl+D propogation)

  - by Vi

  socat - exec:'bash -li',pty,stderr,ctty - bash: no job control in this shell What options should I use to get fully fledged shell as I get with ssh/sshd? I want be able to connect the shell to everything socat can handle (socks5, udp, openssl), but also to have a nice shell which correctly interprets all keys, various Ctrl+C/Ctrl+Z and jobs control. Update: Found "setsid" socat option. It fixes "no job control". Now trying to fix Ctrl+D.

  Read the article

• How can I log when reads to /dev/random block?

  - by ldrg

  I've noticed that since updating my server to Debian Squeeze the amount of entropy as reported by /proc/sys/kernel/random/entropy_avail is much lower than it was before the upgrade. I would like to know if this lower pool size is big enough to function with or if I need to look into getting more entropy sources. I think having a way to log blocking reads of /dev/random would show whether I have enough entropy or not.

  Read the article

• dmidecode showing less Memory Capacity than Motherboard spec?

  - by starchx

  We got a supermicro server, http://www.supermicro.com/products/system/1u/5016/sys-5016i-ur.cfm, according spec, the server supports up to 32G memory when using ECC Register Memory. However, when I tried the dmidecode command, it says 24G max memory: [root@c1 ~]# dmidecode | grep Maximum Maximum Size: 256 kB Maximum Size: 1024 kB Maximum Size: 8192 kB Maximum Memory Module Size: 4096 MB Maximum Total Memory Size: 24576 MB Maximum Capacity: 24 GB Maximum Value: Unknown Which one I should trust?

  Read the article

• IPv4 forward on windows?

  - by silverbandit91

  Is there anything that can forward/redirect all incoming traffic to another ip. Basically I'm looking the windows equivalent of ip forwarding in linux. echo "1" > /proc/sys/net/ipv4/ip_foward

  Read the article

• Windows 7 crashes with a blue screen

  - by Chinook pilot

  I am running win 7 32 bit on a Gateway Media Center. Without any interaction from me, and the only thing on the screen is my screen saver it crashes and the fault is "Stop" and a long string of numbers. I have had a "adapi sys message but now it seems to be this "Stop' MESSAGE. Any help will be appreciated.

  Read the article

• XP Pro SP3: DRIVER_IRQL_NOT_LESS_OR_EQUAL on hibernate

  - by Margaret

  Hey all I'm running XP Pro SP3 on a Late 2007-era 2.2Ghz Macbook. Unfortunately, it's recently started giving me a Blue Screen of Death when I try to hibernate it. It gives me the error "DRIVER_IRQL_NOT_LESS_OR_EQUAL", and at the bottom says that it's in "hiber_atapi.sys". Most of the Googling I've done thus far turns up things referring to Windows Server 2003, which is obviously less than useful. Anyone know any way to fix this short of a full re-install?

  Read the article

• Linux buffer cache effect on IO writes?

  - by Patrick LeBoutillier

  Hi, I'm copying large files (3 x 30G) between 2 filesystems on a Linux server (kernel 2.6.37, 16 cores, 32G RAM) and I'm getting poor performance. I suspect that the usage of the buffer cache is killing the I/O performance. To try and narrow down the problem I used fio directly on the SAS disk to monitor the performance. Here is the output of 2 fio runs (the first with direct=1, the second one direct=0): Config: [test] rw=write blocksize=32k size=20G filename=/dev/sda # direct=1 Run 1: test: (g=0): rw=write, bs=32K-32K/32K-32K, ioengine=sync, iodepth=1 Starting 1 process Jobs: 1 (f=1): [W] [100.0% done] [0K/205M /s] [0/6K iops] [eta 00m:00s] test: (groupid=0, jobs=1): err= 0: pid=4667 write: io=20,480MB, bw=199MB/s, iops=6,381, runt=102698msec clat (usec): min=104, max=13,388, avg=152.06, stdev=72.43 bw (KB/s) : min=192448, max=213824, per=100.01%, avg=204232.82, stdev=4084.67 cpu : usr=3.37%, sys=16.55%, ctx=655410, majf=0, minf=29 IO depths : 1=100.0%, 2=0.0%, 4=0.0%, 8=0.0%, 16=0.0%, 32=0.0%, >=64=0.0% submit : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0% complete : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0% issued r/w: total=0/655360, short=0/0 lat (usec): 250=99.50%, 500=0.45%, 750=0.01%, 1000=0.01% lat (msec): 2=0.01%, 4=0.02%, 10=0.01%, 20=0.01% Run status group 0 (all jobs): WRITE: io=20,480MB, aggrb=199MB/s, minb=204MB/s, maxb=204MB/s, mint=102698msec, maxt=102698msec Disk stats (read/write): sda: ios=0/655238, merge=0/0, ticks=0/79552, in_queue=78640, util=76.55% Run 2: test: (g=0): rw=write, bs=32K-32K/32K-32K, ioengine=sync, iodepth=1 Starting 1 process Jobs: 1 (f=1): [W] [100.0% done] [0K/0K /s] [0/0 iops] [eta 00m:00s] test: (groupid=0, jobs=1): err= 0: pid=4733 write: io=20,480MB, bw=91,265KB/s, iops=2,852, runt=229786msec clat (usec): min=16, max=127K, avg=349.53, stdev=4694.98 bw (KB/s) : min=56013, max=1390016, per=101.47%, avg=92607.31, stdev=167453.17 cpu : usr=0.41%, sys=6.93%, ctx=21128, majf=0, minf=33 IO depths : 1=100.0%, 2=0.0%, 4=0.0%, 8=0.0%, 16=0.0%, 32=0.0%, >=64=0.0% submit : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0% complete : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0% issued r/w: total=0/655360, short=0/0 lat (usec): 20=5.53%, 50=93.89%, 100=0.02%, 250=0.01%, 500=0.01% lat (msec): 2=0.01%, 4=0.01%, 10=0.01%, 20=0.01%, 50=0.12% lat (msec): 100=0.38%, 250=0.04% Run status group 0 (all jobs): WRITE: io=20,480MB, aggrb=91,265KB/s, minb=93,455KB/s, maxb=93,455KB/s, mint=229786msec, maxt=229786msec Disk stats (read/write): sda: ios=8/79811, merge=7/7721388, ticks=9/32418456, in_queue=32471983, util=98.98% I'm not knowledgeable enough with fio to interpret the results, but I don't expect the overall performance using the buffer cache to be 50% less than with O_DIRECT. Can someone help me interpret the fio output? Are there any kernel tunings that could fix/minimize the problem? Thanks a lot,

  Read the article

• Very poor read performance compared to write performance on md(raid1) / crypt(luks) / lvm

  - by Android5360

  I'm experiencing very poor read performance over raid1/crypt/lvm. In the same time, write speeds are about 2x+ faster on the same setup. On another raid1 setup on the same machine I get normal read speeds (maybe because I'm not using cryptsetup). OS related disks: sda + sdb. I have raid1 configuration with two disks, both are in place. I'm using LVM over the RAID. No encryption. Both disks are WD Green, 5400 rpm. IO test results on this raid1: dd if=/dev/zero of=/tmp/output.img3 bs=8k count=256k conv=fsync - 2147483648 bytes (2.1 GB) copied, 22.3392 s, 96.1 MB/s sync echo 3 > /proc/sys/vm/drop_caches dd if=/tmp/output.img3 of=/dev/null bs=8k - 2147483648 bytes (2.1 GB) copied, 15.9 s, 135 MB/s And here is the problematic setup (on the same machine). Currently I have only one sdc (WD Green, 5400rpm) configured in software raid1 + crypt (luks, serpent-xts-plain) + lvm. Tomorrow I will attach another disk (sdd) to complete this two-disk raid1 setup. IO tests results on this raid1: dd if=/dev/zero of=output.img3 bs=8k count=256k conv=fsync 2147483648 bytes (2.1 GB) copied, 17.7235 s, 121 MB/s sync echo 3 > /proc/sys/vm/drop_caches dd if=output.img3 of=/dev/null bs=8k 2147483648 bytes (2.1 GB) copied, 36.2454 s, 59.2 MB/s We can see that the read performance is very very bad (59MB/s compared to 135MB/s when using no encryption). Nothing is using the disks during benchmark. I can confirm this because I checked with iostat and dstat. Details on the hardware: disks: all are WD green, 5400rpm, 64mb cache. cpu: FX-8350 at stock speed ram: 4x4GB at 1066Mhz. Details on the software: OS: Debian Wheezy 7, amd64 mdadm: v3.2.5 - 18th May 2012 LVM version: 2.02.95(2) (2012-03-06) LVM Library version: 1.02.74 (2012-03-06) LVM Driver version: 4.22.0 cryptsetup: 1.4.3 Here is how I configured the slow raid1+crypt+lvm setup: parted /dev/sdc mklabel gpt type: ext4 start: 2048s end: -1 Now the raid, crypt and the lvm configuration: mdadm --create /dev/md1 --level=1 --raid-disks=2 missing /dev/sdc cryptsetup --cipher serpent-xts-plain luksFormat /dev/md1 cryptsetup luksOpen /dev/md1 md1_crypt vgcreate vg_sql /dev/mapper/md1_crypt lvcreate -l 100%VG vg_sql -n lv_sql mkfs.ext4 /dev/mapper/vg_sql-lv-sql mount /dev/mapper/vg_sql-lv_sql /sql So guys, can you help me identify the reason and fix it? It has to be something with the cryptsetup as there is no such read slowdown on the other setup (sda+sdb) where no encryption is present. But I have no idea what to do. Thanks!

  Read the article

• CPU/Mem/Disk utilization (average) after process has completed

  - by BassKozz

  Ubuntu Server 9.10 So there is the time command which will show you the time it took for a specific process/command to run after the command has completed. For example: :~$ time ls real 0m0.020s user 0m0.000s sys 0m0.000s I'd like to also collect the average CPU usage, Memory, and Disk (i/o) utilization after the process has completed using time (or another command if necessary). How can I accomplish this? Mainly I am using this to benchmark MySQL import performance using different innodb_buffer_pool_size settings.

  Read the article

• Nginx + Haproxy + Thin + Rails - 503 Service Unavailable -

  - by Luca G. Soave

  I don't know how troubleshoot this. I get "503 Service Unavailable" http error for all "nginx upstreams" proxy passing calls to haproxy fast_thin and slow_thin ( server 127.0.0.1:3100 and server 127.0.0.1:3200 ), which loadbalance on 6 Thin servers ( 127.0.0.1:3000 .. 3005 ). Static files like /blog are currently fine. The falldown is: nginx on port 80 - haproxy on 3100 and 3200 - thin on 3000 .. 3005 and then Rails. Here it is /etc/nginx/nginx.conf : user nginx; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; sendfile on; tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; include /etc/nginx/conf.d/*.conf; } then /etc/nginx/conf.d/default.conf upstream fast_thin { server 127.0.0.1:3100; } upstream slow_thin { server 127.0.0.1:3200; } server { listen 80; server_name www.gitwatcher.com; rewrite ^/(.*) http://gitwatcher.com/$1 permanent; } server { listen 80; server_name gitwatcher.com; access_log /var/www/gitwatcher/log/access.log; error_log /var/www/gitwatcher/log/error.log; root /var/www/gitwatcher/public; # index index.html; location /about { proxy_pass http://fast_thin; break; } location /trends { proxy_pass http://slow_thin; break; } location /categories { proxy_pass http://slow_thin; break; } location /signout { proxy_pass http://slow_thin; break; } location /auth/github { proxy_pass http://slow_thin; break; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (-f $request_filename/index.html) { rewrite (.*) $1/index.html break; } if (-f $request_filename.html) { rewrite (.*) $1.html break; } if (!-f $request_filename) { proxy_pass http://slow_thin; break; } } } then haproxy config file /etc/haproxy/haproxy.cfg : global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet nbproc 1 # number of processing cores defaults log global retries 3 maxconn 2000 contimeout 5000 mode http clitimeout 60000 # maximum inactivity time on the client side srvtimeout 30000 # maximum inactivity time on the server side timeout connect 4000 # maximum time to wait for a connection attempt to a server to succeed option httplog option dontlognull option redispatch option httpclose # disable keepalive (HAProxy does not yet support the HTTP keep-alive mode) option abortonclose # enable early dropping of aborted requests from pending queue option httpchk # enable HTTP protocol to check on servers health option forwardfor # enable insert of X-Forwarded-For headers balance roundrobin # each server is used in turns, according to assigned weight stats enable # enable web-stats at /haproxy?stats stats auth haproxy:pr0xystats # force HTTP Auth to view stats stats refresh 5s # refresh rate of stats page listen rails_proxy 127.0.0.1:3100 # - equal weights on all servers # - maxconn will queue requests at HAProxy if limit is reached # - minconn dynamically scales the connection concurrency (bound my maxconn) depending on size of HAProxy queue # - check health every 20000 microseconds server web1 127.0.0.1:3000 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3001 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3002 weight 1 minconn 3 maxconn 6 check inter 20000 listen slow_proxy 127.0.0.1:3200 # cluster for slow requests, lower the queues, check less frequently server slow1 127.0.0.1:3003 weight 1 minconn 1 maxconn 3 check inter 40000 server slow2 127.0.0.1:3004 weight 1 minconn 1 maxconn 3 check inter 40000 server slow3 127.0.0.1:3005 weight 1 minconn 1 maxconn 3 check inter 40000 and the Thin config file /etc/thin/gitwatcher.yml : --- chdir: /var/www/gitwatcher environment: production address: 0.0.0.0 port: 3000 timeout: 30 log: log/thin.log pid: tmp/pids/thin.pid max_conns: 1024 max_persistent_conns: 100 require: [] wait: 30 servers: 6 daemonize: true if I look into open listen ports, I got the following : root@fullness:/var/www/gitwatcher# lsof | grep TCP | egrep "nginx|haproxy|thin" nginx 834 root 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 835 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 837 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) haproxy 1908 haproxy 4u IPv4 11699 0t0 TCP localhost:3100 (LISTEN) haproxy 1908 haproxy 6u IPv4 11701 0t0 TCP localhost:3200 (LISTEN) root@fullness:/var/www/gitwatcher# iptables -L get me the following : Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:22222 ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT all -- anywhere anywhere DROP all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Any help ?

  Read the article

• prevent filesystem from entering read-only mode

  - by user788171

  I have found that my server's filesystem is continuously entering read-only mode. There have been some issues with the raid1 array, but I have removed the bad disk from the array. However, it is still physically plugged into the system because I haven't had a chance to go over to the datacentre, I suspect udev and the system kernel is still picking up the bad disk and throwing errors. In /var/log/messages, there are errors like this: Mar 2 06:53:14 nocloud kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen Mar 2 06:53:14 nocloud kernel: ata1: irq_stat 0x00400040, connection status changed Mar 2 06:53:14 nocloud kernel: ata1: SError: { PHYRdyChg DevExch } Mar 2 06:53:14 nocloud kernel: ata1: hard resetting link Mar 2 06:53:20 nocloud kernel: ata1: link is slow to respond, please be patient (ready=0) Mar 2 06:53:21 nocloud kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 2 06:53:21 nocloud kernel: ata1.00: configured for UDMA/133 Mar 2 06:53:21 nocloud kernel: ata1: EH complete This happens fairly randomly throughout the day until eventually the filesystem becomes read-only. When this happens, my system becomes non-operational which kind of defeats the purpose of having a raid1. Note, ata1 is the bad disk (I think ata1 corresponds to /dev/sda because they are both first in line). Under mdadm, /dev/sda1,2 is no longer being used, but I can't prevent the system kernel from continuing to query that disk when I am no longer using it and throwing these errors. Is there a way to prevent my filesystem from automatically going into read-only mode? Furthermore, is it safe to do so? Thanks in advance. EDIT: Additional information: output from cat /proc/mdstat md1 : active raid1 sdb2[1] 976554876 blocks super 1.1 [2/1] [_U] bitmap: 5/8 pages [20KB], 65536KB chunk md0 : active raid1 sdb1[1] 204788 blocks super 1.0 [2/1] [_U] Output from mount: /dev/mapper/VolGroup-LogVol00 on / type ext4 (rw,noatime) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw,rootcontext="system_u:object_r:tmpfs_t:s0") /dev/md0 on /boot type ext4 (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) EDIT2: pvdisplay output: --- Physical volume --- PV Name /dev/md1 VG Name VolGroup PV Size 931.32 GiB / not usable 2.87 MiB Allocatable yes (but full) PE Size 16.00 MiB Total PE 59604 Free PE 0 Allocated PE 59604

  Read the article

• socat and "no job control in this shell"

  - by Vi

  socat - exec:'bash -li',pty,stderr,ctty - bash: no job control in this shell What options should I use to get fully fledged shell as I get with ssh/sshd? I want be able to connect the shell to everything socat can handle (socks5, udp, openssl), but also to have a nice shell which correctly interprets all keys, various Ctrl+C/Ctrl+Z and jobs control. /* Requested tags: socat job-control */

  Read the article

• Virtual Server 2005 VSS writer missing

  - by Jon S.

  I have two servers running Virtual server 2005 R2 SP1. I'm using Symantec Backup Exec 10d for backups. One server runs the backups fine but the other will cause the vm's to crash when it tries to backup. I think the problem is because the "Microsoft Vitual Server 2005 Writer" is not showing up when I run "vssadmin list writers". Can I install the writer without reinstalling VS 2005?

  Read the article

• Don't see job schedule in SQL Mgmt UI added by sp_add_jobschedule

  - by Ariel

  I'm running a script like below on a SQL Server box and, even though it finishes correctly, then when, on SQL Mgmt UI, I right click on that job's properties, go to Schedules, I cannot see the schedule just added... what am I missing? (I'm using the right job_name param, etc) thanks! BEGIN TRY BEGIN TRAN EXEC msdb.dbo.sp_add_jobschedule @job_name = 'Job name', @name=N'Job schedule name', @enabled = 0, @freq_type=1, @active_start_date=20100525, @active_start_time=60000 COMMIT TRAN END TRY BEGIN CATCH SELECT ERROR_Message(), ERROR_Line(); ROLLBACK TRAN END CATCH

  Read the article

• server will not reply (syn -ack)

  - by Brent

  I like to use the following commands to manage 'TIME_WAIT', in the hope to free up resources. echo 20 > /proc/sys/net/ipv4/tcp_fin_timeout sysctl -w net.ipv4.tcp_tw_reuse=1 sysctl -w net.ipv4.tcp_tw_recycle=1 I found something interesting while doing a tcpdump. Sometimes if a client makes a connection (syn), the server will not reply (syn -ack). My question is, could it be because of the top three commands.

  Read the article

• Linux Fiber Channel Host Setup Basic

  - by Jim

  I've been googling for about 4 hours now with no luck. I am trying to setup a Linux server running Oracle Server 6.3 as a Fiber Channel host. And then connect it to a Dell Compellent Fibre Channel Host contain a 500GB Volume. The Oracle server itself contains two Brocade 815 FC HBAs. I've discovered their WWN(I think) via cat /sys/class/fc_host/host1/port_name 0x100000051efc3d85 cat /sys/class/fc_host/host2/port_name 0x100000051efc3d9f The next part is where I am at a loss. I've used iSCSI before...is FC the same deal where you have an initiator and a target? If so where do I specific that in linux? I'm also new to Fiber Channel as a protocol, so i am unsure what is needed to make a transaction? WWN and port ID? Similar to IP:Port combination in the Ethernet world. I've read alot regarding using systool, multipath, fc_transport commands, however none of these is recognized as a valid command from Oracle Server 6.3 Appreciate the guidance and assistance. I installed sccsi-target-utils and can now run rescan-scsi-bus and sg_map -x. rescan-scsi-bus.sh -l -w -r Host adapter 0 (megaraid_sas) found. Host adapter 1 ((null)) found. Host adapter 2 ((null)) found. Host adapter 3 (ata_piix) found. Host adapter 4 (ata_piix) found. Scanning SCSI subsystem for new devices and remove devices that have disappeared Scanning host 0 for SCSI target IDs 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15, LUNs 0 1 2 3 4 5 6 7 Scanning for device 0 2 0 0 .... OLD: Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC H700 Rev: 2.30 Type: Direct-Access ANSI SCSI revision: 05 Scanning for device 0 2 1 0 ... OLD: Host: scsi0 Channel: 02 Id: 01 Lun: 00 Vendor: DELL Model: PERC H700 Rev: 2.30 Type: Direct-Access ANSI SCSI revision: 05 Scanning host 1 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning for device 1 0 3 1 ... OLD: Host: scsi1 Channel: 00 Id: 03 Lun: 01 Vendor: COMPELNT Model: Compellent Vol Rev: 0505 Type: Direct-Access ANSI SCSI revision: 05 Scanning host 2 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning host 3 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning for device 3 0 0 0 ... REM: Host: scsi3 Channel: 00 Id: 00 Lun: 00 DEL: Vendor: TEAC Model: DVD-ROM DV-28SW Rev: R.2A Type: CD-ROM ANSI SCSI revision: 05 Scanning host 4 channels 0 for SCSI target IDs 0, LUNs 0 1 2 3 4 5 6 7 0 new device(s) found. 1 device(s) removed. and sg_map -x /dev/sg0 0 0 32 0 13 /dev/sg1 0 2 0 0 0 /dev/sda /dev/sg2 0 2 1 0 0 /dev/sdb /dev/sg4 1 0 3 1 0 /dev/sdc I'm not sure what this all means...

  Read the article

• how to escape the ' in ssh?

  - by Dean Hiller

  I need to escape the ' in this command for ssh exec grep IPADDR /etc/sysconfig/network-scripts/ifcfg-eth0 |awk -F= '{print $2}' How do I escape that? I currentl y have this which does not work ssh host 'grep IPADDR /etc/sysconfig/network-scripts/ifcfg-eth0 |awk -F= '{print $2}'' nor does this ssh host 'grep IPADDR /etc/sysconfig/network-scripts/ifcfg-eth0 |awk -F= \'{print $2}\'' thanks, Dean

  Read the article

• Windows NT Service shutdown issues

  - by Jeremiah Gowdy

  I have developed middleware that provides RPC functionality to multiple client applications on multiple platforms within our organization. The middleware is written in C# and runs as a Windows NT Service. It handles things like file access to network shares, database access, etc. The middleware is hosted on two high end systems running Windows Server 2008 R2. When one of our server administrators goes to reboot the machine, primarily to do Windows Updates, there are serious problems with how the system behaves in regards to my NT Service. My service is designed to immediately stop listening for new connections, immediately start refusing new requests on existing connections, and otherwise shut down as rapidly as possible in the case of an OnStop or OnShutdown request from the SCM. Still, to maintain system integrity, operations that are currently in progress are allowed to continue for a reasonable time. Usually the server shuts down inside of 30 seconds (when the service is manually stopped for example). However, when the system is instructed to restart, my service immediately loses access to network drives and UNC paths, causing data integrity problems for any open files and partial writes to those locations. My service does list Workstation (and thus SMB Redirector) as a dependency, so I would think that my service would need to be stopped prior to Workstation/Redirector being stopped if Windows were honoring those dependencies. Basically, my application is forced to crash and burn, failing remote procedure calls and eventually being forced to terminate by the operating system after a timeout period has elapsed (seems to be on the order of 20-30 seconds). Unlike a Windows application, my Windows NT Service doesn't seem to have any power to stop a system shutdown in progress, delay the system shutdown, or even just the opportunity to save out any pending network share disk writes before being forcibly disconnected and shutdown. How is an NT Service developer supposed to have any kind of application integrity in this environment? Why is it that Forms Applications get all of the opportunity to finish their business prior to shutdown, while services seem to get no such benefits? I have tried: Calling SetProcessShutdownParameters via p/invoke to try to notify my application of the shutdown sooner to avoid Redirector shutting down before I do. Calling ServiceBase.RequestAdditionalTime with a value less than or equal to the two minute limit. Tweaking the WaitToKillServiceTimeout Everything I can think of to make my service shutdown faster. But in the end, I still get ~30 seconds of problematic time in which my service doesn't even seem to have been notified of an OnShutdown event yet, but requests are failing due to redirector no longer servicing my network share requests. How is this issue meant to be resolved? What can I do to delay or stop the shutdown, or at least be allowed to shut down my active tasks without Redirector services disappearing out from under me? I can understand what Microsoft is trying to do to prevent services from dragging their feet and showing shutdowns, but that seems like a great goal for Windows client operating systems, not for servers. I don't want my servers to shutdown fast, I want operational integrity and graceful shutdowns. Thanks in advance for any help you can provide. PS in regards to writing my own middleware, this is for a telephony application with sub-second "soft-realtime" response time requirements. It does make sense, and it's not a point I'm looking to debate. :)

  Read the article

• Volume Shadow Copy not starting

  - by Gram

  Hi We are running a Windows 2008 Small Business Server with Symantec Backup Exec. Last night the back up failed due to the Volume Shadow Copy service being unable to start. When I try to manually start it I get the following error "windows could not start the volume shadow copy on local computer" Has anybody any suggestions other than rebooting the server? many thanks Graham

  Read the article

• Not able to Defrag my drive for shrink even using PerfectDisk on Windows 7

  - by Mithun Sasidharan

  I want to partition my c drive which has over 450gb capacity of which hardly 30gb is being used. I deleted the pagefile.sys and also disabled hibernate and cache memory. I then defragmented and consolidated free space using PerfectDisk 12 and also run a boot time defragmented. Now what remains is Metadata files that preventing me from shrinking the volume beyond half the size if disk. Please tell me what to do?????

  Read the article

• Dynamic rewrite rule - based on a hitcounter OR timestamp

  - by Derek Adair

  Hi, Sorry for the lack of coherence with sys-admin stuff... I'm a programmer ;) I have the need to switch front-end's of a website based on either a hit-counter or some kind of timer (related question). Is this possible with mod_rewrite? any other interesting techniques? Thanks

  Read the article

• SQL Server: can SecurityAdmin role read error log?

  - by atricapilla

  I have read, e.g from here http://wiki.lessthandot.com/index.php/Find_Out_Server_Roles_For_a_SQL_Server_Login that SecurityAdmin role can read Error logs. I'm on SecurityAdmin role and when I try to execute xp_readerrorlog I get a following error: Msg 229, Level 14, State 5, Procedure xp_readerrorlog, Line 1 The EXECUTE permission was denied on the object 'xp_readerrorlog', database 'mssqlsystemresource', schema 'sys'. What I'm missing? Can this role read error logs or not?

  Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >