Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 157/783 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• Windows Virtual Machine not seen by host (Mac OS X) using VMWare Fusion

  - by Malkuth

  Hi, I installed Windows XP with VMware Fusion on my MacBook and while internet works, Windows can ping the Mac, etc. from the Mac or any other machine in the network we can not see the Virtual Machine. In between, I use bridged option and obtain the the VM's IP dynamically; tried also static assignment from the free addresses but the problem persisted. Any ideas what is wrong?

  Read the article

• Using two ports on my ZyXel USG gateway to patch two devices together?

  - by Matthew Beza

  I don't know if this is possible but it would save me many long drives! I have drawn, with my epic MS Paint skills, my current setup. I have a ZyXel USG300 Gateway with a built in 5 port switch. It supports bridging, tunnles, VLANs, etc.. I have a Cisco WLC2112 plugged into port 6 (P6). The cisco is set to 192.168.6.2 and P6 is set to 192.168.6.1. This works but I need to incorporate a Nomadix AG3000 to handle guests. (Router (A) in the picture). So I need the Cisco WLC2112 to use the Nomadix as if it where plugged into it's LAN port. Right now the Nomadix WAN Port is plugged into (P2) on the ZyXel, and the Nomadix LAN port is plugged into (P3). Is it possible to set something up where (P3) and (P6) are somehow "Patched" as if the Cisco was plugged directly into the Nomadix LAN port? Basically making the ZyXel a fancy Cat5e coupler?

  Read the article

• Synergy on macbook with osx mavericks wifi connection

  - by user332956

  I'm trying to set up Synergy with my macbook pro running OS X 10.9.3 as a client and my Windows 7 desktop as a server. I'm having some pretty bad connection problems though when I try to use my mac. Every couple seconds the mouse or the keyboard will stop working entirely then come back. I ran some tests and found that the ping from my desktop to my mac would be very high every third ping or so(1000+ ms) or sometimes even time out. If I ping my desktop from my mac the pings are all reasonably low. I believe that this is a power saving feature of Mavericks and I have found a way to get around it by continually pinging my router on my mac, keeping my wifi card from going to sleep. I'm using this right now to type this up with synergy and have had zero issues. Has anyone else ran into this issue and found a better solution? So far, I think my best bet would be to buy an ethernet adapter but I'd rather not have yet another cable running across my desk.

  Read the article

• Disable (or switch off) a network interface on windows but keep the "plug and play"

  - by Leandro

  I'm looking for a good workaround to do this on Windows 7 and Windows XP: Disable or make ineffective the network interface (ETH, WIFI, any NIC). If the user connect his ETH cable, the network interface enable again. Important Notes to take care: I'm working with wmic on Win7 (through the command line) I'm working with devcon on WinXP (through the command line) I'm specifically working with the .NET Framework 2.0 on C# but this is just for informational purposes. I know that an event won't help me to detect it (if there is a way or workaround to do this I don't know it). The real problem is that when I disable the NIC, I can't know if the user connects his cable or has a wired network. This is why I am looking for a workaround. I'll treat suggestions as answers if no direct answer exists. I'll provide any extra detail necessary.

  Read the article

• NFS performance troubleshooting

  - by aix

  I am troubleshooting NFS performance issues on Linux, and I'm looking at the following nfsiostat output: host:/path mounted on /path: op/s rpc bklog 96.75 0.01 read: ops/s kB/s kB/op retrans avg RTT (ms) avg exe (ms) 86.561 1408.294 16.269 0 (0.0%) 34.595 89.688 write: ops/s kB/s kB/op retrans avg RTT (ms) avg exe (ms) 10.113 326.282 32.265 0 (0.0%) 19.688 72446.246 What exactly is the meaning of avg RTT (ms) and avg exe (ms)? avg exe for writes is 72 seconds(!) -- would you say this is abnormal and, if so, how do I go about troubleshooting this further? I'm using NFS over TCP. Both the client and the server are on the same GigE LAN.

  Read the article

• rhel/centos vs. ubuntu (possibly other debian-based systems) linux in handling duplicate ips in the same subnet

  - by johnshen64

  This has bothered me for quite a while but I never found out why or how to change the behavior. ip duplicates could be caused by typos or dhcp errors etc., but they do occur from time to time. in rpm-based systems such as centos, the old server with the duplicate ip wins, and the new server will get an error in bringing up the nic (ip address already used). this is somewhat harmless because we can just fix the system that is coming up. ubuntu only the other hand happily grabs the used ip for itself and leave the old server/device without a valid ip. this is the more dangerous behavior because it causes outages. what i want is to change the ubuntu behavior to that of the centos/rhel so would appreciate any help.

  Read the article

• ESET Remote Administrator Console showing infected files on a client, but threat log is empty

  - by Aron Rotteveel

  We recently deployed ESET NOD32 Antivirus on our small domain network and use the Remote Adminstrator to manage everything remotely. On a recent full system scan, one of the clients shows 10 infected files of which 4 have been cleaned in the scan log. The strange thing, however, is that the threat log is empty. Is there any reason why the threat log is empty? What has happened to the 6 remaining uncleaned files? Where can I view information on what files are infected and what they have been infected with? I know this can be done through the scan log properties screen, but with 958790 files scanned, I obviously do not want to browse through this list. Any help is appreciated.

  Read the article

• Dhcpd Daemon is trying to lease itself?

  - by tommieb75

  I have a Slackware Linux 13.0 box with two interfaces, eth0 and eth1. I have set this box up to be on the 192.168.1.0/24 network, with subnet mask of 255.255.255.0. I am trying to run a dhcpd server on this box to service two interfaces above, so I subnetted the 192.168.1.0/24 network into two subnets. For eth0 192.168.1.1, subnet mask 255.255.255.128, broadcast mask 192.168.1.127. For eth1 192.168.1.129, subnet mask 255.255.255.128, broadcast mask 192.168.1.255. Both the interfaces are assigned manually. eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.1 Bcast:192.168.1.127 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:39 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1404 (1.3 KiB) Interrupt:11 Base address:0x8000 Memory:faffc000-faffcfff eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.128 Bcast:192.168.1.255 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10003 errors:0 dropped:0 overruns:0 frame:0 TX packets:13286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1589229 (1.5 MiB) TX bytes:9900005 (9.4 MiB) Interrupt:11 Here is the dhcpd.conf set up authoritative; ddns-update-style interim; ignore client-updates; subnet 192.168.1.0 netmask 255.255.255.128 { range 192.168.1.2 192.168.1.126; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.127; option subnet-mask 255.255.255.128; } subnet 192.168.1.128 netmask 255.255.255.128 { range 192.168.1.129 192.168.1.254; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.255; option subnet-mask 255.255.255.128; } This is what is showing in the log Apr 10 18:09:58 inspiron8600 dhcpd: DHCPDISCOVER from 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:09:58 inspiron8600 dhcpd: DHCPOFFER on 192.168.1.131 to 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:10:01 inspiron8600 dhcpcd[3832]: eth1: adding IP address 169.254.153.6/16 This is happening spuriously, and the log gets filled up with nonsense..so my question is this: How do I stop this from happening? And why would it be trying to give itself a lease? I am sure I have missed something but cannot see it and would appreciate a pair of eyes from the community to spot the obvious flaw!

  Read the article

• When I ping Internet addresses like yahoo or Google, I get 2 reply packets and 2 lost packets.

  - by navi

  I have Airtel broadband and a Tata broadband connection. i have around 50 PCs connecting through an airtel broadband connection. Both are dsl connections with my phone line going into dsl modems and an Ethernet cable going from dsl modem directly into a switch. Currently, only airtel connection is connected with static IP on my private lan and using the airtel ISP DNS servers as DNS IP address and the default gateway is 192.168.1.1 (IP add. of the dsl modem). All PCs are connected in a work group. When in full use, my users complain of certain web pages are not opening. When I ping Internet addresses like Yahoo or Google I get 2 reply packets and 2 lost packets. I suspect that a single broadband connection is not able to sustain 50 simultaneous downloads/browsing. Is there any device which connect to both DSL and make one line so that its give me high speed simultaneous browsing. Help needed urgently. Thank you all to those who reply.

  Read the article

• Second ip address on same interface CentOS 6.3

  - by user16081

  I tried to add a second LAN addresses in CentOS 6.3 on a brand new install and it's not working. I installed a new copy of CentOS 5.7 and tried the same and it worked right away. Now I'm just trying to setup the alias on the same subnet and it's not working. what am i doing wrong, is this not possible on CentOS 6.3? second ip address on the same interface but on a different subnet CentOS 5.7 it works: DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:01:6F:89 IPADDR=192.168.0.167 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes DEVICE=eth0:0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:01:6F:89 IPADDR=192.168.0.166 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes On CentOS 6.3: does not work DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:1E:DE:86 IPADDR=192.168.0.242 NETMASK=255.255.255.0 NETWORK=192.168.0.0 GATEWAY=192.168.0.1 ONBOOT=yes DNS1=205.134.232.138 DNS2=4.4.4.4 DEVICE=eth0:0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:1E:DE:86 IPADDR=192.168.0.240 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes # /etc/init.d/network restart Shutting down interface eth0: Device state: 3 (disconnected) [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK Bringing up interface eth0: Active connection state: activated Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/3 [ OK ] # ping 192.168.0.240 PING 192.168.0.240 (192.168.0.240) 56(84) bytes of data. From 192.168.0.242 icmp_seq=2 Destination Host Unreachable Appreciate any advice, thanks Update: Perhaps this is relevant? On CentOS 5.7: # dmesg |grep eth eth0: registered as PCnet/PCI II 79C970A eth0: link up eth0: link up On 6.3: # dmesg | grep eth e1000 0000:02:00.0: eth0: (PCI:66MHz:32-bit) 00:0c:29:1e:de:86 e1000 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None 8021q: adding VLAN 0 to HW filter on device eth0 eth0: no IPv6 routers present

  Read the article

• tomato firmware unstable when I am connected to Chromecast

  - by Graviton

  I have an Asus RT-N12D1, and I installed the tomato firmware by shibby ( version tomato-K26-1.28.RT-N5x-MIPSR2-112-Max.trx). However I found that the connection can be really unstable. Whenever I stream youtube videos on TV via Chromecast ( I tried both the cast from iPad and Win7, both can reproduce the problem), the router will frequently restart itself, leading to a loss of connection and subsequent reconnection. I want to get this problem fixed, but I don't know how. Is there anyway where I can troubleshoot what is the real problem, or is there anyway I can collect enough log information so that I can then present to the original developer for a fix ( maybe)?

  Read the article

• How to get Windows 7 to automatically connect to an ad-hoc network?

  - by George Edison

  I have two machines - one is running Ubuntu 12.04 64-bit and the other is running Windows 7 Starter Edition (32-bit). The Ubuntu machine is connected to the Internet via the eth0 interface. That machine also has a wireless network interface (wlan0) that is currently functioning as an ad-hoc network. I can connect to the ad-hoc network just fine with the Windows machine but each time I wish to do so, I must manually initiate the connection and enter the password. Is there some way to instruct Windows to automatically connect to this network (an option I have for standard wireless networks but not ad-hoc networks)?

  Read the article

• Unable to authenticate to Windows Server 2003 for file browsing as non-administrator user.

  - by Fopedush

  I've got a windows server 2003 box containing a raid 5 array I use for mass storage. I want to set up a special non-administrator account that can be used to browse files over the network, with only read access. Ideally I'll map my network drive as this user to avoid accidentally hosing my data, and mount as an administrator user on occasions where I actually need write access. I've created a non-administrator user on the Windows Server box (called "ReadOnly)", and granted the user read permissions on the folders I need. However, when I try to browse to the files, and authenticate as this user, I'm told "Permission denied". If I throw the readOnly user into the administrators group, however, I can authenticate and browse just fine. I am, of course, only attempting to browse to folder for which I have given this user read permissions. Obviously my ReadOnly user is missing some privilege here, but I can't figure out what it is. I've been digging around in group policy editor all day to no avail. What am I missing? Fake Edit: I'm doing my browsing from a Windows 7 box, but I don't think that is relevant.

  Read the article

• Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem

  - by zchads

  Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem. Hardware Information: Buffalo Wireless Router/access point, Model: WZR-HP-G300NH-AP DSL Modem: Generic (actually not sure of manufacture). Service Provider: TOT (Thailand) Laptop-1: Windows XP and Belkin PCMIA Network Card Laptop-2: Windows XP unknown network card & Wifi Laptop-3: Windows 7 unknown network card & Wifi Outline of Problem/actions taken: After a recent power failure the router and laptop-1 connected to router were no longer able to access the internet. Actions taken to try and recover internet access: Using Laptop-1 tried to configure Router with PPPoe settings using software from Router Manufacture. During the installation process a Timeout error was experienced, unable to connect to WAN. Used Internet Explorer to communicate directly with Router using IP address. Changed settings to use PPPoe settings given by ISP. Router was not able to communicate with Internet. Repeated steps 1-4 again with no success. Reset Router and DSL modem. Repeated steps 1-4 again still no success. Tried connecting Laptop-1 directly to DSL to gain access to internet to research problem. No Network connection with DSL could be established…connection would be established for a second and then be lost and didn’t appear long enough to actually connect to DSL. Replugged LAN back into Router and connection was regained with laptop-1. Replugged Laptop-1 directly into DSL and again unable to establish network connection. Uninstalled network card and all of its drivers on Laptop-1. Reinstalled network card and drivers and tried connecting directly to DSL. Still unable to make network connection. Plugged DSL into Laptop-3 and Internet connection was established. Being Laptop-3 does not have a CD-Rom, Laptop-2 was tried to connect to the router. With Laptop-2 steps 1-7 ended up being repeated without success. Tried plugging Laptop-2 directly into DSL and again no network connection could be established. Using Laptop-3 with a direct connection to DSL downloaded latest Router FW. Installed router FW using Laptop-1. Tired the installation process again without success. Being desperate reinstalled OS on Laptop-1 still not success. Tried using “ipconfig” with router to see what was going on without success. With laptop-1 connected to DSL went through the “ipconfig /…” inputs to see if anything made a difference. Being the network card was not able to make a connection this provide very little information “media disconnected”. So now I have a router and two laptops which are unable to connect to the internet and sure could use some advice/help.

  Read the article

• Multiple Homed Windows 2008 Server / Windows 7 Client

  - by Daniel Scott

  I have a small Windows 2008 network, with some Windows 7 clients. The clients are both laptops with docking stations and I would like them to communicate with the Windows 2008 server (for filesharing) through the wired network whilst they're docked. Internet connectivity for all machines (clients and server) is via a Wireless LAN, so the wireless adapter in the Windows 7 clients stays active while they're docked. When the laptops are un-docked, it would be nice to still be able to contact the windows 2008 server for print sharing (and slower file sharing) - hence the server also being on the wireless LAN. The windows 2008 server is running Active Directory, DHCP and DNS. It controls DHCP leases on the wired network and holds the DNS records for "myserver.mycompany.local", which is what the filesharing clients connect to. Ideally I'd like the DNS records to return the wired IP first so that this is the address that the laptops will attempt initially - but there doesn't seem to be a way to do that? At present the server's IP on the wireless LAN comes out of an nslookup above the wired Lan IP. The multi-homing works perfectly - but in the wrong order! Switch on the wireless lan and ping myserver and it goes to the wireless IP. Disable the wireless on the client and do the same ping again and after a couple of seconds it starts pinging the wired address. Does anyone have any suggestions on how to make this work in a predictable order? - or even if it can work. Alternative 1? If it can't work, then would this work: Remove the wireless adapter from the server, put a wireless router/bridge on the wired network (set up to route to/from the wireless LAN's subnet), then configure the clients with two routes to the (now) single IP of the server with metrics favouring direct communication over the wired LAN first? Alternative 2? Should I instead single-home the laptops so all of their connectivity is via the wired-LAN while they're docked? (and route via the windows 2008 server - or a dedicated wireless bridge/router)? My concern here is that I'd like undocking to be seamless - and if the clients are in the middle of downloading something from the internet I wouldn't want whatever they're doing interupted as they switch IP addresses onto the Wireless network. Perhaps this isn't the case and I'm concerned over nothing? Any thoughts? :) UPDATE I seem to have cracked it (at least DNS entries come out in the order I hope for - and pinging the server with various combinations of wired, wireless and both interfaces enabled uses the IP I want) ... I set the binding order of the NICs on the Server (which is acting as Domain Controller, DHCP and DNS server) so that the Wired NIC is before the Wireless adapter. (Start -- type "Network Interfaces" -- Select "View Network Connections" -- Press Alt to show classic dropdown menus -- Advanced -- Advanced Settings) Now, an nslookup (from the client) of the server's hostname returns the Wired IP first, followed by the Wireless IP. The wired IP now seems to be used whenever it's contactable. Incidentally, the metrics on the wired and wireless routes (on the client) also favour the wired LAN (based on Windows' automatically assigned metrics) - but this was always the case, even when I was having trouble getting the wired IP to be "favoured". I'm not entirely sure if this is coincidence - or if a DNS server running on Windows, handing back IP addresses for itself does actually take the binding order of it's own network interfaces into account? It would be interesting to hear from someone who can confirm or deny that (or confirm that the binding order on the server plays a role for some other reason?)

  Read the article

• display internet usage agreement before users can use internet

  - by Force Flow

  I was looking for a way to display a usage agreement page in browsers that users must agree to before they are allowed to access the internet. This would be for users on public computers and public/open wifi. I'm using a sonicwall firewall which does support this feature, however, there is a rediculously low character limit which makes it impractical to use. I thought about setting the browser's homepage to a usage agreement page, but that can easily be bypassed by navigating to somewhere else. Are there any other approaches that may be worth considering? There is currently no server in place on the public network, though I can set one up if need be.

  Read the article

• How do I maximize and check my gigabit transfer rate?

  - by J Penguin

  I'm trying to maximize my LAN transfer speed. LAN cards and switch are all gigabit on a CAT 6 cable. Modes are set correctly to 1000 full duplex. CentOS server Testing with ftp from both windows and fedora, I'm only having the speed around 11MB/s. On windows I notice that the first few seconds of file transfer I'm actually getting around 25MB/s before it drops to 11MB/s Can anyone please recommend me what my next step should be to increase this performance? Are there any utilities I can use to test the file transfer speed without taking hard drive speed into consideration? The only thing I know is the MTU which I will have to wait until the office hour is over before I can play with it. If there are anything else I should be aware of, please please let me know. Thank you!

  Read the article

• iMac G5 20" (First All-In-One White Screen) Cannot Connect To Internet

  - by Goober

  The Scenario I've got an iMac G5 20" (First All-In-One White Screen) PPC. It has an Airport Extreme Network card in order to wirelessly to connect to the internet. For the most part I connect using ethernet as opposed to wirelessly, but recently have had the need to connect using the wireless. The Hardware BT Home Broadband Wireless Router. iMac G5 20" From about 5 years ago (First All-In-One White Screen) The Issue Even though I know for a fact that It has connected to the internet wireslessly in the past, for some reason it can discover the wireless router, but upon entering the password it fails to connect. I have tried multiple times to no avail. I have 2 other Mac's on the network and a pc that can all connect wirelessly. However both the mac's. Question Any ideas as to why my really old iMac G5 can't connect wirelessly anymore!?

  Read the article

• How can I run a speed test for Netflix and Hulu?

  - by Brennan Stehling

  Since the FCC rules were struck down I have noticed that Netflix and Hulu often stall on my Time Warner home connection. I've heard others are experiencing the same delays. I use Speedtest.net regularly from my computer and phone to check my connection and typically at home I get 10 to 15Mbps and occasionally higher. Currently it is around 10Mbps yet Hulu is stalling. Is there a way to specifically test my speeds for streaming Netflix and Hulu?

  Read the article

• Two network cards in one Windows 7 PC

  - by Martin

  Hi, I've upgraded from Vista to Windows 7. On Vista I used to run one network card (Intel 82566DC -2 Gigabit) for my internet which was connected to a Dovado USB mobile broadband router connected to a 3G modem. The IP setup on the card is set on DHCP. The second card (3com Ethernet link) was used to connect to our town's local WUG (wireless user group) and all worked fine. Now the problem I have with Windows 7 is that when I connect to the internet with the (Intel) first card, the internet work fine but as soon as I connect the second card to the wug my internet drops. If I then disconnect the first card (internet one) and try to connect to the wug it works. It seems that the two cards are fighting each other. Is there maybe something I can do to fix the problem? As you probably can gather from this post is that I am not an expert on PC's so please if you do answer do I in simple terms. :) Thanks, Martin

  Read the article

• IBM Tivoli Network Manager IP Edition - Job does not run

  - by Thorsten Niehues

  Since our network discovery takes too long I tried to split the biggest job into two parts. The two parts use the same Perl script but have a different scope. I copied a Job (Agent) doing the following: Copied the .agnt file Copied the associated perl script The problem is that one or the other job (changes randomly) does not run. The Disco Process will fail eventually. In the log of the job which does not run I see the following error message: Wed Jul 18 08:48:54 2012 Warning: Failed to send on transport layer found in file CRivObjSockClient.cc at line 1293 - Client My_MacTable_Cis is not connected to service Helper How do I fix this problem?

  Read the article

• Virtualbox completely disabled my ethernet and wireless network connections

  - by Tawani

  After installing VirtualBox 3.1.6 for Windows, my computer's network connections were completely disabled. The wireless isn't working, not even the ethernet landline. Even "ipconfig" doesn't seem to respond to any commands. Can anybody help?

  Read the article

• Event ID 8021 The browser was unable to retrieve a list of servers from the browser master

  - by Ash

  We have a LAN where workstations are randomly losing network connectivity for brief moments of time. The workstations can also take a long time to login to the domain. During our troubleshooting we have found an error log on a few Windows 7 workstations: Warning BROWSER 8021 The browser was unable to retrieve a list of servers from the browser master \\random-pc on the network \Device\NetBT_Tcpip_{BBABCDE9-D8A0-4399-93F2-492FE0848B12}. The data is the error code. What do these errors mean? What computers should have the Computer Browser service enabled, workstations and/or servers? The environment is a mix of Windows 7 & Windows XP workstations on a Windows Server SBS 2011 SP1 domain.

  Read the article

• Changing the mac address in a libvirt xml config file breaks network connectivity for the guest

  - by foob

  I'm using Xen with libvirt and trying to set it up on a bridged interface. I am able to install an OS and everything works as I would expect. If I save the xml output from "virsh dumpxml guest", edit the mac address for the interface, and then define the domU with this new xml file I find that traffic is no longer forwarded from the vif0.0 interface to br0. The ifcfg-eth0 file on the guest was automatically updated to reflect the new mac address and the ifconfig output looks the same. Does anyone know why this is happening or how to properly change the mac address for a libvirt configuration?

  Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >