Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 162/783 | < Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Two identical fiber optic broadband lines working as one

  - by Katafalkas

  I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

  Read the article

• Domain connection shows as "unauthenticated"

  - by gareth89

  I have seen various different questions for this problem floating around but either the circumstances arent the same or the solution doesnt work so thought i would post it to see if anybody has any suggestions. Various domain PCs and laptops appear to randomly give the connection name of "lewis.local 2(Unauthenticated)" - lewis.local being our domain - and provides an exclamation mark where the network type logo is normally shown. This also appears to happen every time connecting via vpn. Our setup is: 2 servers both running windows server 2003 R2 (x32) main server has AD, DNS and DHCP installed IPv4 on approx 30 client machines (some wired, some wireless) If anybody has any thoughts on solutions i would appreciate it. I have tried removing all but AD server roles, resetting all of the systems and nothing. It doesnt prevent anything from working just like a domain connection most of the time however it is getting fustrating! Also dont know if it could have anything to do with it but the DHCP server seems to have quite a long lead time on issuing the IP address to the client.

  Read the article

• How can Windows XP/7 users cleanly connect to Mac OS X Server 10.9.4 Mavericks with Active Directory integration?

  - by JakeGould

  I’m a Linux/Unix systems admin who also manages a Macintosh server infrastructure & there is a lone Mac Mini in the mix running 10.9.4 that I would like Windows XP & Windows 7 users to connect to with little or no hassle. The problem? Windows users can’t seem to even get to the point of a password prompt yet connect. Mind you this server replaced a Mac OS X 10.6.8 server that had issues, but never had issues with Windows users connected. The gist of this post is: The tons of different messages out there about Mac OS X 10.9.4 Samba support are mind-numbingly confusing. Can anyone share some solid specifics here? I’ve read pieces like this one here that suggest turning off file sharing & then adding a share with AFP/SMB enabled would work. But the suggestion seems to apply to 10.8. And from what I know a lot has changed in Samba support in 10.9 let alone the iterations to 10.9.4. Then I found this great tutorial here that explains things step-by-step. Which seems like it should work, but the problem is the example given applies to a local user created on the Mac when I would like users in an Active Directory group—which the Mac is bound to—access the Mac Mini shares. There are also tons of great tips here on MacWindows.com but nothing seems solid to the issue I am facing. So from what I am reading these are my options: Local User Versus Active Directory: Setup a common local user on the Mac OS X 10.9.4 server to be used for Samba sharing since Active Directory won’t work. Is this really the case? Because loss of AD integration is a major pain. Do Extended File Attributes Get Retained from Windows Users: If this were to work, how do extended attributes come into play? Loss of metadata & related info is not an option. How Fragile is Any of this to Updates: How does any of this shake out with Mac OS X updates as well as Windows updates? Installing Official, Open Source Samba: Would upgrading the Samba install on the server to the official open source Samba via a package like SMBUp or via the Hombrew method described here help or make the issue worse? I fully understand there have historically been issues in mixed environments, but nowadays Windows users connecting to a Mac seem to have a truly hellish road ahead of them. Unless I am missing something?

  Read the article

• Network transfer from host to VM very slow - VMWare Server & Windows 2003 Server

  - by barfoon

  Hey everyone, Im trying to transfer a file from a Windows 7 host running VMWare Server to a Windows 2003 server VM, and it's painfully slow. I've tried adding/adjusting registry keys and settings found on KB articles, and still nothing. Ive tried this: http://support.microsoft.com/kb/898468 http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1619 Vmware tools are installed. Any ideas? Thanks,

  Read the article

• Looking for a fiber optic "switch" or "router" for home use

  - by Shrout1

  The gist of my question: What is a "fiber optic" switch called? I.E. a layer 2 ethernet switch that uses fiber TX and RX connections and sends layer 2 network traffic between the fiber strands that are connected. Can someone purchase a dedicated fiber switch that does not have copper ethernet ports? What is the current average price of a device like this? Not necessarily looking for product endorsements, just information Might not make sense to go this route if it is too cost prohibitive What type of fiber connector is used for terminating a fiber strand into a jack on the wall? Can fiber be "patched" using two jacks and a "patch" cable? Is signal loss a concern with the longest runs at 100-200ft, a patch cable and media converters? The full story: My parents had unterminated fiber optic cable and terminated Cat5e run throughout their home when it was built in 2004. 10 years later the Cat5e isn't providing the throughput that my father needs to accomplish multiple streams of HD and fast system backups throughout the house. He can't reach gigabit speeds across the distance of the Cat5e runs. We are both interested in terminating the fiber connections and using them as high speed "backbones" to copper switches in each room of the house. It would be easy to attain gigabit speeds (or better, eventually) using the fiber. I have searched and searched for a "fiber optic switch" or "fiber optic router" and cannot find the correct term to describe this piece of hardware. We can use fiber media converters at the end points of each connection, however it would be nice to have a "patch panel" set up in the network closet in the basement that has fiber connections on it and switches the ethernet streams between the connections/systems in the house. Each fiber media converter costs between $50-$100 a piece... After 10 or so terminated connections it might make sense to find a piece of hardware that does not require media converters. That would depend upon the cost of this hardware Somewhat unrelated, if we are able to route between these fiber strands successfully, what is the physical connector type used in a jack on the wall? Just like RJ45 has a wall outlet (depicted below): What is the fiber optic equivalent of this? In the interim could we "patch" a couple fiber strands together in the network closet? Would signal loss be of concern with a run length of 100-200 feet, a patch cable and two media converters? If that would work then it could be used until the funds are available for more.

  Read the article

• How to skip pushing the default gateway via DHCP in OpenWRT?

  - by francadaval

  I have a router with OpenWRT that I want to resolve IP addressing with DHCP without setting a default gateway. I have added a DHCP-Option parameter with value 3,0.0.0.0 that is supposed to set the default gateway by DHCP. Instead, the router IP is defined as default gateway for DHCP connections. How can I set a null default gateway (0.0.0.0) for connections configuration by DHCP? As said in a comment: I want this router to service a VirtualBox network that doesn't set a default gateway via DHCP.

  Read the article

• Detecting man-in-the-middle attacks?

  - by Ilari Kajaste

  There seem to be many possible ways to create man-in-the-middle attacks on public access points, by stealing the access point's local IP address with ARP spoofing. The possible attacks range from forging password request fields, to changing HTTPS connections to HTTP, and even the recently discovered possibilit of injecting malicious headers in the beginning of secure TLS connections. However, it seems to be claimed that these attacks are not very common. It would be interesting to see for myself. What ways are there to detect if such an attack is being attempted by someone on the network? I guess getting served a plain HTTP login page would be an obvious clue, and of course you could run Wireshark and keep reading all the interesting ARP traffic... But an automated solution would be a tiny bit more handy. Something that analyzes stuff on the background and alerts if an attack is detected on the network. It would be interesting to see for myself if these attack are actually going on somewhere.

  Read the article

• TCP/IP Ilustrated 1 second edition [on hold]

  - by user196821

  Well, I want to read and learn about how tcpip works in detail, so I got a copy of the well known book of Richard Stevens. But after a little, I discovered there is a second edition of the book, so I checked it out. But surprisingly, the second edition does not cover some subjects that the first actually does (like telnet, ftp, smtp etc...), so I thought "well I just have to read the misshing chapters on the first edition", but if they removed them in the second, it is for a reason. Is there really a good reason for that?

  Read the article

• Making hosts accessible between LAN subnets

  - by nixnotwin

  I have two inerfaces on my router with tomato firmwre: br0 and vlan4. br0 is on 192.168.0.0/16 subnet and vlan4 on 10.0.1.0/24 subnet. As I don't want the different network services on br0 available on vlan4, I have added this firewall rule: iptables -I INPUT -i vlan4 -j ACCEPT; iptables -I FORWARD -i vlan4 -o vlan2 -m state --state NEW -j ACCEPT; iptables -I FORWARD -i br0 -o vlan4 -j DROP; vlan2 is my WAN (internet acess). The issue that I want to solve is that I want to make one host from 192.168.0.0/16 network (br0), which has ip 192.168.0.50, available on vlan4 (10.0.1.0/24). Only that host should be available on vlan4 (and all other hosts on br0 should be inaccessible). What firewall rules can be used to do it? Edit 1: Output of iptables -nvL FORWARD: Chain FORWARD (policy DROP 4 packets, 204 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- vlan4 192.168.0.50 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan4 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 229 13483 ACCEPT all -- vlan4 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 DROP all -- br0 vlan3 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan3 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 67 3405 ACCEPT all -- vlan3 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 ACCEPT all -- br0 br0 0.0.0.0/0 0.0.0.0/0 34 1360 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 758 40580 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 11781 2111K restrict all -- * vlan2 0.0.0.0/0 0.0.0.0/0 26837 19M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 wanin all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 287 15927 wanout all -- * vlan2 0.0.0.0/0 0.0.0.0/0 283 15723 ACCEPT all -- br0 * 0.0.0.0/0 0.0.0.0/0 0 0 upnp all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 Output of iptables -t nat -nvL PREROUTING: Chain PREROUTING (policy ACCEPT 6887 packets, 526K bytes) pkts bytes target prot opt in out source destination 855 83626 WANPREROUTING all -- * * 0.0.0.0/0 222.228.137.223 0 0 DROP all -- vlan2 * 0.0.0.0/0 192.168.0.0/16 0 0 DNAT udp -- * * 192.168.0.0/16 !192.168.0.0/16 udp dpt:53 to:192.168.0.1

  Read the article

• Why the server is not responding?

  - by par

  Hello! Our server occasionally refuses to serve a simple HTML page. This is happening during a relatively high number of requests. However, the processor is not heavy loaded and there are a lot of free memory. The error seems to occure 1 out of 50 requests in average, depending on the server load. I need to find the source of the problem and take the appropriate actions to eliminate it. I have a suspicion that the problem source is a huge number of incoming network packets. There are 5000 packets per second on average. Traffic - 2 MBits/sec Can this be the cause of the error? There is an interesting thing, in case the server fails to respond, the request string is not logged to access.log by Apache. The error is repeatable from several client computers. DNS is not involved, since I have accessed the server by the IP. I have profiled the problem case with tcpdump utility. These are the good and bad sessions traced by tcpdump. The request is the same in both experiments. Good - server returns response. Bad - no response, time-out error. ---- Bad ---- 12:23:36.366292 IP 123.45.67.890.61749 > myserver.superbservers.com.www: S 2125316338:2125316338(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:23:39.362394 IP 123.45.67.890.61749 > myserver.superbservers.com.www: S 2125316338:2125316338(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:23:45.365567 IP 123.45.67.890.61749 > myserver.superbservers.com.www: S 2125316338:2125316338(0) win 8192 <mss 1460,nop,nop,sackOK> -------- ---- Good ---- 12:27:07.632229 IP 123.45.67.890.63914 > myserver.superbservers.com.www: S 3581365570:3581365570(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:27:10.620946 IP 123.45.67.890.63914 > myserver.superbservers.com.www: S 3581365570:3581365570(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:27:10.620969 IP myserver.superbservers.com.www > 123.45.67.890.63914: S 2654770980:2654770980(0) ack 3581365571 win 5840 <mss 1460,nop,nop,sackOK,nop,wscale 6> 12:27:10.838747 IP 123.45.67.890.63914 > myserver.superbservers.com.www: . ack 1 win 4380 12:27:10.957143 IP 123.45.67.890.63914 > myserver.superbservers.com.www: P 1:213(212) ack 1 win 4380 12:27:10.957152 IP myserver.superbservers.com.www > 123.45.67.890.63914: . ack 213 win 108 12:27:10.965543 IP myserver.superbservers.com.www > 123.45.67.890.63914: P 1:630(629) ack 213 win 108 12:27:10.965621 IP myserver.superbservers.com.www > 123.45.67.890.63914: F 630:630(0) ack 213 win 108 12:27:11.183540 IP 123.45.67.890.63914 > myserver.superbservers.com.www: . ack 631 win 4222 12:27:11.185657 IP 123.45.67.890.63914 > myserver.superbservers.com.www: F 213:213(0) ack 631 win 4222 12:27:11.185663 IP myserver.superbservers.com.www > 123.45.67.890.63914: . ack 214 win 108 -------- Hoster: SuperbHosting OS: Ubuntu Server parameters: E6300 CONROE 1.86GHZ 2 X 1MB CACHE 1066 1GB DDR2 667MHZ This is a link to apache configuration file we use http://repkin5.snow.prohosting.com/apache.txt This is server-status report taken right after time-out error. http://repkin5.snow.prohosting.com/server-status.htm There are only 10 Child Servers running out of 120, so enough space for new requests. VMSTAT procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 8900 725900 8468 65684 0 0 5 18 11 33 4 3 92 1

  Read the article

• Extend my LAN network

  - by user268291

  i have a patch panel and hardwiring already setup in my office. The patch panel is 24-port and all the ports are engaged. All my switch ports are engaged. Now, I have a printer connected to a wall point (RJ45) which I want to shift to a new room where there is no LAN setup. I want to have two RJ45 wall plugs in the new room so that I can connect one RJ45 port to have my LAN in the new room and the other RJ45 wall port I want to use for my printer. There is no option other than LAN (no wireless). Please help me and tell me how do I get the two RJ45 wall plate plugs in the new room up and keep my LAN running. It is a little urgent for me. Please help.

  Read the article

• Ping isn't acting accurate?

  - by Earlz

  I've been trying to diagnose some latency issues with my internet connection. I've been lagging out of online video games and such, which of course could be their server's fault. So, I've been running ping some. It doesn't indicate anything unusual, but it does act a bit strange. I can start it with something like ping internethost -i 0.1 so that it will send a ton of packets, and every 10-20 seconds it will appear to just freeze for 2 or 3 seconds. The packets are still being received in the right order though, and there is no packet loss. The weirdest thing is that after the little freeze up, it will usually just report a ping time that is about 10-30ms higher than the average. How does this happen? Is ping still being accurate? I'm using Arch Linux. The host I'm pinging is my website, which shouldn't be doing any kind of ping slowing or filtering.

  Read the article

• Easiest way to send encrypted email?

  - by johnnyb10

  To comply with Massachusetts's new personal information protection law, my company needs to (among other things) ensure that anytime personal information is sent via email, it's encrypted. What is the easiest way to do this? Basically, I'm looking for something that will require the least amount of effort on the part of the recipient. If at all possible, I really want to avoid them having to download a program or go through any steps to generate a key pair, etc. So command-line GPG-type stuff is not an option. We use Exchange Server and Outlook 2007 as our email system. Is there a program that we can use to easily encrypt an email and then fax or call the recipient with a key? (Or maybe our email can include a link to our website containing our public key, that the recipient can download to decrypt the mail?) We won't have to send many of these encrypted emails, but the people who will be sending them will not be particularly technical, so I want it to be as easy as possible. Any recs for good programs would be great. Thanks.

  Read the article

• Troubleshooting an unstable internet connection

  - by Konrad Rudolph

  My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

  Read the article

• How to route HyperV VMs traffic through host VPN

  - by Random

  I'm using Windows 8.1 Pro with HyperV. I have several VMs for development, all of them connected with host via Internal adapter using network addresses: 192.168.10.0/24 Where: 192.168.10.1 is my host's Hyper-V internal NIC address. When I'm not in my office I use 3G usb dongle an dialup VPN connection. I would like to route traffic from all existing and future VMs through the VPN. In best scenario traffic would be routed only partially to the local company network addresses 10.1.1.0/24 I don't want to use sharing because I'm switching between WiFi, USB 3G dongle and VPN. Moving to other virtualization is also not an option for me.

  Read the article

• Sonicwall 3500 (Creating VLANS for usage of multiple SSID)

  - by Thomas Chia

  I have an issue here. Here is my setup: X0 - STAFF network | X2 - AGENT network | X4 - Wireless AP (for multiple SSID) Okay, basically I'm going to set up the wireless AP to be broadcasting 2 SSID, STAFF-WIFI and AGENT WIFI. When connected to STAFF-WIFI, the users will be connected to the STAFF network, while connected to the AGENT WIFI, the users will be connected to the AGENT network. Can someone explain in details how to go about setting up this configuration? Thanks!

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• How to stop a infinite running process(ztail) started by a ssh session after that session is closed

  - by Sanath Adiga

  I have a peculiar problem. My server supports multiple ssh session simultaneously, so that multiple admins can manage it simultaneously. We have a command which calls ztail to show the compressed log files and when the current ssh session is closed (without pressing ctrlc, to stop the tail command), the command should ideally stop working. But what I observed when I start a new ssh session is that the process ztail is still running in the background and consuming CPU, even though the previous session was closed. How can I determine when the session is closed, so that I can use that variable/flag to close/stop any commands initiated by that previously closed session?

  Read the article

• VPN Network intermittantly fails to provide internet: What could be possible causes

  - by Jake M

  We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

  Read the article

• How to set up DHCP-configured access through a Linux box?

  - by marcusw

  I would like an old desktop box to use my laptop as a router to access the internet. Here is my setup: I have one ethernet port in the side of my laptop which I want to use to get internet access to my desktop computer. The laptop is connected to the LAN via a wireless link. Both systems run Linux. The desktop autoconfigures itself using DHCP. The laptop is a Kubuntu system. I do not have any crossover cables, though wireshark on the laptop sees the DHCP requests from the desktop just fine, so I doubt that I need one. What do I have to do to make this work?

  Read the article

• What keeps you from changing your public IP address and wreak havok?

  - by Whitemage

  An interesting question was asked to me and I did not know what to answer.. So I'll ask here. Let's say I subscribed to an ISP and I'm using cable internet access. ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let's say, 60.61.62.75 and mess with another consumer's internet access? For the sake of this argument, let's say that this other IP address is also owned by the same ISP. Also, let's assume that it's possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gaetway, a network address and a broadcast address. So that's 3 addresses the ISP "loses" to you. That seems very wastefull for dynamically assigned IP addresses where the majority of customers are.. Could they simply be using static arps? ACLs? Other simple mechanisms? Anyone who worked at an ISP would be willing to explain this a bit?

  Read the article

• Any way to stop VMWare workstation from dropping SSH connections?

  - by oljones

  I have VMWare workstation 8 with a few Linux guests. I have had problems maintaining an active SSH connection to my VMs when they are in bridged mode. I first read that the onboard realtek network cards were not well supported so I bought a Intel Pro/1000 GT card. This supposedly had support. But this made no difference. Connections via SSH are active for about the first 3 minutes then hang and die. I have changed the TCP Checksum offload on the Intel and Realtek NICs, but this only works some of the time and even then not for very long. The best I could do was about 20 minutes before the connection was dropped. Any ideas?

  Read the article

• Anytime I upload something, my internet slows down extremely. What can I do?

  - by Earlz

  Title says it all. For a bit more info though: Basically, I have Time Warner cable internet. My speeds maintain a stable 2Mbit/s upload and 20Mbit/s download with average ping times around 30ms. This crazy thing happens though when I upload anything. I went to upload a 200M file to my server today through sftp and my internet completely choked up. I speed tested it during this upload and my ping time was around 800ms, download speeds of 0.2Mbit/s and Upload speeds of 0.3Mbit/s. Note, I wasn't downloading anything during this time either. It is just straight upload. What is it that causes this phenomenon? My router is OpenBSD. Is there anything I could set up to fix this problem(by queues or some such), or is this a problem with cable internet?

  Read the article

< Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >