Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 197/1221 | < Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >

  • How do I get network working on a Dell n5010 - Ubuntu 10.04

    - by cyberroger
    Hey. I just formatted a Dell n5010 and installed Ubuntu 10.04. Now,when i try to access the Internet it doesn't find the available networks. Informations about it: My network is set to broadcast SSID; Already typed lspci, and it doesnt returns my wireless card; Tried installing windows drivers from fabricant cd usind diswrapper, but it says it cant complete the installation because it cant find some "Device" folder; I don't know what else to do, I switch the wireless button on/off and it just can't see any wireless connection, includin mine. Here are the informations about lspci: *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fbc00000-fbc03fff And this: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 12:00.0 Network controller: Broadcom Corporation Device 4727 (rev 01) 13:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Thanks!

    Read the article

  • Unable to set default gateway

    - by GrandMasterFlush
    I'm running Ubuntu server via Hyper-V and have successfully installed it but seem unable to ping the server or ping any other machines on the network from the server. After doing a bit of reading I've noticed that the default gateway isn't set but when I try and set it I keep getting error messages which I can't understand. From this article I've tried ip route add default via 10.0.10.200 Which reports: RTNETLINK answers: Operation not permitted If I try running it prefixed with sudo but it reports: `RNETLINK answers: No such process I've editted /etc/network/interfaces but when I start the machine and type netstat -nr there is nothing listed. Can anyone tell me where I'm going wrong please? EDIT : /etc/network/interfaces contains: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp

    Read the article

  • How do I efficiently code both the client and server at the same time?

    - by liamzebedee
    I'm coding my game using a client-server model. When playing on singleplayer, the game starts a local server, and interacts with it just like a remote server (multiplayer). I have done this to avoid coding separate singleplayer and multiplayer code. I have just started coding and have encountered a major problem. Currently I'm developing the game in Eclipse, having all the game classes organized into packages. Then, in my server code, I just use all the classes in the client packages. The problem is, these client classes have variables that are specific to rendering, which obviously wouldn't be performed on a server. Should I create modified versions of the client classes to use in the server? Or should I just modify the client classes with a boolean, to indicate if its the client/server using it. Are there any other options I have? I just had a thought about maybe using the server class as the core class, then extending it with rendering stuff?

    Read the article

  • What Keeps You from Changing Your Public IP Address and Wreaking Havoc on the Internet?

    - by Jason Fitzpatrick
    What exactly is preventing you (or anyone else) from changing their IP address and causing all sorts of headaches for ISPs and other Internet users? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Whitemage is curious about what’s preventing him from wantonly changing his IP address and causing trouble: An interesting question was asked of me and I did not know what to answer. So I’ll ask here. Let’s say I subscribed to an ISP and I’m using cable internet access. The ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let’s say, 60.61.62.75, and messing with another consumer’s internet access? For the sake of this argument, let’s say that this other IP address is also owned by the same ISP. Also, let’s assume that it’s possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gateway, a network address and a broadcast address. So that’s 3 addresses the ISP “loses” to you. That seems very wasteful for dynamically assigned IP addresses, which the majority of customers are. Could they simply be using static arps? ACLs? Other simple mechanisms? Two things to investigate here, why can’t we just go around changing our addresses, and is the assignment process as wasteful as it seems? The Answer SuperUser contributor Moses offers some insight: Cable modems aren’t like your home router (ie. they don’t have a web interface with simple point-and-click buttons that any kid can “hack” into). Cable modems are “looked up” and located by their MAC address by the ISP, and are typically accessed by technicians using proprietary software that only they have access to, that only runs on their servers, and therefore can’t really be stolen. Cable modems also authenticate and cross-check settings with the ISPs servers. The server has to tell the modem whether it’s settings (and location on the cable network) are valid, and simply sets it to what the ISP has it set it for (bandwidth, DHCP allocations, etc). For instance, when you tell your ISP “I would like a static IP, please.”, they allocate one to the modem through their servers, and the modem allows you to use that IP. Same with bandwidth changes, for instance. To do what you are suggesting, you would likely have to break into the servers at the ISP and change what it has set up for your modem. Could they simply be using static arps? ACLs? Other simple mechanisms? Every ISP is different, both in practice and how close they are with the larger network that is providing service to them. Depending on those factors, they could be using a combination of ACL and static ARP. It also depends on the technology in the cable network itself. The ISP I worked for used some form of ACL, but that knowledge was a little beyond my paygrade. I only got to work with the technician’s interface and do routine maintenance and service changes. What keeps me from changing this IP address to, let’s say, 60.61.62.75 and mess with another consumer’s internet access? Given the above, what keeps you from changing your IP to one that your ISP hasn’t specifically given to you is a server that is instructing your modem what it can and can’t do. Even if you somehow broke into the modem, if 60.61.62.75 is already allocated to another customer, then the server will simply tell your modem that it can’t have it. David Schwartz offers some additional insight with a link to a white paper for the really curious: Most modern ISPs (last 13 years or so) will not accept traffic from a customer connection with a source IP address they would not route to that customer were it the destination IP address. This is called “reverse path forwarding”. See BCP 38. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

    Read the article

  • Suspending my laptop breaks ethernet over firewire, are there commands which can fix it?

    - by Josh
    As mentioned in this question I am using a firewire cable to provide a private network between my laptop and my desktop, because it makes using the screen sharing program synergy much nicer than using WIFI. However when I leave my office for the day and I suspend my laptop, when I return the next day, the desktop and the laptop cannot communicate over firewire anymore. The firewire0 device still has an IP address. but when I try and ping the desktop I get no route to host I'm using kernel 2.6.35-24-generic #42-Ubuntu SMP x86_64 on Ubuntu 10.10. Is there some way I can remedy this without a reboot? Like, removing some kernel modules and re-inserting them? Here's what I have tried so far and the results: root@token:~# dmesg|tail -n 1 [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 root@token:~# modprobe -r firewire_net firewire_ohci firewire_core root@token:~# modprobe -v firewire_ohci insmod /lib/modules/2.6.35-24-generic/kernel/lib/crc-itu-t.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-core.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-ohci.ko root@token:~# dmesg|tail [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592563.410868] firewire_ohci: Removed fw-ohci device. [592579.160086] firewire_ohci: Added fw-ohci device 0000:02:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2 [592579.160137] firewire_ohci: isochronous cycle inconsistent [592579.660294] firewire_core: created device fw0: GUID 0000000000000000, S400 [592579.663805] firewire_core: created device fw1: GUID 0017f2fffe89bce6, S400 [592579.663813] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700720] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700842] firewire_core: refreshed device fw0 [592579.702603] firewire_net: firewire0: IPv4 over FireWire on device 0000000000000000 root@token:~# ping stan.firewire PING stan.firewire (192.168.100.1) 56(84) bytes of data. From token.local (192.168.100.3) icmp_seq=1 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=2 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=3 Destination Host Unreachable I also tried removing the modules prior to suspending, and re-inserting after resuming. This did not work either :-(

    Read the article

  • Aser Aspire 3690 WIreless Not working, new Ubuntu user

    - by drew
    I don't know that much about Ubuntu, but I put it on an Acer Aspire 3690 Laptop (replaced Win Vista). Everything seems to work fine, but the wireless connection. It says "FIRMWARE MISSING". It detects that I have a wireless card, so I don't know what to do. I've already used the "ADDITIONAL DRIVERS" thing, and that didn't work. I've googled and have not found anything helpful. I don't really know what I'm doing, so can your directions please be kindergarden level? Thank you very much for any help you can provide. I really appreciate it.

    Read the article

  • Can not connect to wireless on 12.04 with Intel WiFi Link 5100

    - by WiData
    I am having problem in connecting to wifi. I have dual boot (Windows 7 and Ubuntu 12.04) on my Dell Studio 15. I upgraded to 12.04 quite some time ago (at least one month) from 11.10. Everything was working fine till yesterday. Since yesterday I can see the list of available Wifi connection but does not connect to any or if connects (after hours of trying) then disconnects after few minutes. My wifi interface is Intel WiFi Link 5100 AGN. However the problem is on both Windows and Ubuntu. Here are outputs of some commands which may be useful for those interested in helping: ~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:22:19:fa:65:bb UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:794 errors:0 dropped:0 overruns:0 frame:0 TX packets:794 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:56280 (56.2 KB) TX bytes:56280 (56.2 KB) wlan0 Link encap:Ethernet HWaddr 00:22:fb:d2:fc:ce UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:239 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:53603 (53.6 KB) Here is the output for the command sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fb:d2:fc:ce width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-48-generic-pae firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:f8000000-f8001fff My kernel version is kernel version 3.2.0-48-generic-pae I also checked this post which was helpful. But I am not sure if what is the exact problem. Any suggestions will be helpful. Should I be changing the firmware/driver? Currently my /lib/firmware has following iwlwifi files /lib/firmware/iwlwifi-1000-5.ucode /lib/firmware/iwlwifi-5000-5.ucode /lib/firmware/iwlwifi-100-5.ucode /lib/firmware/iwlwifi-5150-2.ucode /lib/firmware/iwlwifi-105-6.ucode /lib/firmware/iwlwifi-6000-4.ucode /lib/firmware/iwlwifi-135-6.ucode /lib/firmware/iwlwifi-6000g2a-5.ucode /lib/firmware/iwlwifi-2000-6.ucode /lib/firmware/iwlwifi-6000g2a-6.ucode /lib/firmware/iwlwifi-2030-6.ucode /lib/firmware/iwlwifi-6000g2b-6.ucode /lib/firmware/iwlwifi-3945-2.ucode /lib/firmware/iwlwifi-6050-5.ucode /lib/firmware/iwlwifi-4965-2.ucode Thanks a lot for the help.

    Read the article

  • Client side latency when using prediction

    - by Tips48
    I've implemented Client-Side prediction into my game, where when input is received by the client, it first sends it to the server and then acts upon it just as the server will, to reduce the appearance of lag. The problem is, the server is authoritative, so when the server sends back the position of the Entity to the client, it undo's the effect of the interpolation and creates a rubber-banding effect. For example: Client sends input to server - Client reacts on input - Server receives and reacts on input - Server sends back response - Client reaction is undone due to latency between server and client To solve this, I've decided to store the game state and input every tick in the client, and then when I receive a packet from the server, get the game state from when the packet was sent and simulate the game up to the current point. My questions: Won't this cause lag? If I'm receiving 20/30 EntityPositionPackets a second, that means I have to run 20-30 simulations of the game state. How do I sync the client and server tick? Currently, I'm sending the milli-second the packet was sent by the server, but I think it's adding too much complexity instead of just sending the tick. The problem with converting it to sending the tick is that I have no guarantee that the client and server are ticking at the same rate, for example if the client is an old-end PC.

    Read the article

  • Wireless not detected on an hp Pavilion g6

    - by Earl Larson
    I just bought an HP Pavilion g6 laptop and I installed Natty Narwhal alongside Windows 7. In Windows 7, my WiFi works perfect but in Ubuntu it absolutely (no matter what I do) won't detect my home WiFi network. Here is the output of "lspci": earl@ubuntu:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200] 01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 03:00.0 Network controller: Ralink corp. Device 5390 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01) earl@ubuntu:~$

    Read the article

  • Handling packet impersonating in client-server model online game

    - by TheDespite
    I am designing a server-client model game library/engine. How do I, and should I even bother to handle frequent update packet possible impersonating? In my current design anyone could copy a packet from someone else and modify it to execute any non-critical action for another client. I am currently compressing all datagrams so that adds just a tad of security. Edit: One way I thought about was to send a unique "key" to the verified client every x_time and then the client has to add that to all of it's update packets until a new key is sent. Edit2: I should have mentioned that I am not concerned about whether the actions described in the packet are available to the client at the time, this is all checked by the server which I thought was obvious. I am only concerned about someone sending packets for another client.

    Read the article

  • Unable to keep the connecting using a wireless bridge

    - by dan
    I am running Ubuntu 12.04 on a dell inspiron desktop (core 2 duo) and am using wicd to manage my network/wifi. I've found that the WiFi card in the machine has trouble staying connected to my router (I believe this is a function of distance between the two), so I've taken an old Belkin F5d7231 wireless router and installed dd-wrt on it to use as a wireless bridge hoping that it will have better reception. I think everything up through the wireless bridge is working OK since I have no problems accessing the internet through it with my MacBook. The problem arises when I try to hook the ubuntu machine up to the wireless bridge. It will connect for a few minutes, but it will quickly disconnect without clear triggering event; it may be more likely to disconnect if there is a heavy traffic load going over it (could be something as simple as "cat big_text_file" in an ssh session). I've tried switching from dhclient to dhcpcd without much improvement. Here is the output from the syslog when it connects: Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: exiting Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: exiting Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:10:08 Chicabuntu kernel: [15184.976127] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.010805] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: exiting Jun 30 17:10:08 Chicabuntu kernel: [15185.180156] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.212785] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:10 Chicabuntu kernel: [15187.027445] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:10:10 Chicabuntu kernel: [15187.027452] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:10:10 Chicabuntu kernel: [15187.028300] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: dhcpcd 3.2.3 starting Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: hardware address = 00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: DUID = 00:01:00:01:17:81:85:79:00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: broadcasting for a lease Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:10:20 Chicabuntu kernel: [15197.568016] eth0: no IPv6 routers present Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: offered 192.168.1.111 from 192.168.1.254 Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: checking 192.168.1.111 is available on attached networks Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: leased 192.168.1.111 for 86400 seconds Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding IP address 192.168.1.111/24 Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding default route via 192.168.1.254 metric 0 Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: exiting Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv4 for mDNS. Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Registering new address record for 192.168.1.111 on eth0.IPv4. Jun 30 17:10:30 Chicabuntu dhcpcd.sh: interface eth0 has been configured with new IP=192.168.1.111 Jun 30 17:10:39 Chicabuntu ntpdate[28439]: adjust time server 91.189.94.4 offset 0.001915 sec And here is the syslog from when it shuts down the connection without reason: Jun 30 17:12:15 Chicabuntu kernel: [15312.575455] tg3 0000:3f:00.0: eth0: Link is down Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: sending signal 1 to pid 28361 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: received SIGHUP, releasing lease Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: exiting Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for 192.168.1.111 on eth0. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing default route via 192.168.1.254 metric 0 Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: No such process Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing IP address 192.168.1.111/24 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: Cannot assign requested address Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: exiting Jun 30 17:12:16 Chicabuntu dhcpcd.sh: interface eth0 has been brought down Jun 30 17:12:17 Chicabuntu kernel: [15313.612141] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.644703] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: exiting Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: exiting Jun 30 17:12:17 Chicabuntu kernel: [15313.912147] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.944746] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:18 Chicabuntu kernel: [15315.592569] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:12:18 Chicabuntu kernel: [15315.592576] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:12:18 Chicabuntu kernel: [15315.593399] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:12:29 Chicabuntu kernel: [15325.680019] eth0: no IPv6 routers present If this isn't useful, I can also post the wicd log, but that is kind of long. If anyone could help me I would be eternally grateful.

    Read the article

  • Akka react vs receive

    - by Will I Am
    I am reading my way through Akka tutorials, but I'd like to get my feet wet with a real-life scenario. I'd like to write both a connectionless UDP server (an echo/ping-pong service) and a TCP server (also an echo service, but it keeps the connection open after it replies). My first question is, is this a good experimental use case for Akka, or am I better served with more common paradigms like IOCP? Would you do something like this with Akka in production? Although I understand conceptually the difference between react() and receive(), I struggle to choose one or the other for the two models. In the UDP model, there is no concept of who the sender is on the server, once the pong is sent, so should I use receive()? In the TCP model, the connection is maintained on the server after the pong, so should I use react()? If someone could give me some guidance, and maybe an opinion on how you'd design these two use cases, it would take me a long way. I have found a number of examples, but they didn't have explanations as to why they chose the paradigms they did.

    Read the article

  • Ubuntu Server 12.04 as a router. Problem with DNS

    - by Lorenzo
    I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

    Read the article

  • What are the best social places for programmers to interact?

    - by Chevex
    I know this is not really the right place for this type of question, but I figure it will get me started and hopefully won't be closed right off the bat. I love the programming industry a lot, but I don't have many colleagues that aren't introverted and/or anti-social, or self-centered. What are some good places online to find programming friends that I could share my adventures with? I love stack overflow but it is more technical and doesn't really allow you to put up a personal project just for people to see and critique. Any suggestions? A good forum would be great! The only ones I can find are usually full of inexperienced people who just "want" to be a programmer. I'm looking more for a place who's members are already programmers discussing programming topics.

    Read the article

  • Can't load some domain

    - by Grzegorz
    I can't load some domain on my ubuntu 13.04: youtube.com translate.google.com drive.google.com vk.com When I ping them they are responding: PING youtube.com (217.119.79.59) 56(84) bytes of data. 64 bytes from non-registered.plix.pl (217.119.79.59): icmp_req=1 ttl=59 time=21.9 ms 64 bytes from non-registered.plix.pl (217.119.79.59): icmp_req=2 ttl=59 time=20.5 ms 64 bytes from non-registered.plix.pl (217.119.79.59): icmp_req=3 ttl=59 time=21.3 ms --- youtube.com ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2002ms rtt min/avg/max/mdev = 20.544/21.255/21.914/0.560 ms But they don't load in any browser like firefox, chrome, lynx. They load in my media centre on XBMCbuntu.

    Read the article

  • ubuntu 13.04 - wireless settings help

    - by James Ellis
    Im having problems connecting my wifi in Ubuntu 13.04 So i was wondering if filling in the data manually ie: the IPv4, IPv6, the SSID and BSSID info etc. I did try this before but maybe i put in the wrong data or maybe not enough Would that make it work?? I just dont know how to find out some of the data you need to put in or if im putting the wrong stuff in??? Im new and its confusing. does anyone know the solution?

    Read the article

  • What is needed for a networked home printer?

    - by Jay
    I've seen this question: Home network printer recommendations but I think I'm asking something more basic. I'm not really familiar with networked printers or how they work or what they do really. What I'd like is to have a printer that is accessible to anyone connected to my home network, without having to plug into the printer itself. An alternative setup might to be to have a printer that is always hooked up to one computer, like a desktop, that is almost always on and allows other computers connected on the network to print to it as well. I believe the first option is called a networked printer and the second is printer sharing. But again I'm new to this so I don't really know the details or if I'm using the correct terminology. I was wondering if someone might be able to shed some light on this and let me know what is needed for either of these setup. Thanks.

    Read the article

  • Secure login for a game that is open source

    - by David Park
    I am making a game which i will be open sourcing. Its a simple arcade like game but requires a network connection because it is meant to be played with other people. The thing i am worrying about is how would i be sure that the client is the one that i put out for the end user to play with? Kind of a like of sv_pure for Team Fortress 2. I was thinking of different ways to combat this such as the server requesting the client's version or even it's md5 hash but people with simple java knowledge could just force a method to always return what the server wants.

    Read the article

  • How to disable the Social Reader Application in Facebook?

    - by Rekha
    Social Reader Application has made the process of sharing in Facebook easy but it looks like whatever we read is being displayed in our Facebook’s page. How to avoid this sharing? In the recent days, everyone’s Facebook Page is being flooded with various news from all the Social Reader Applications we have enabled. Even though this is a good idea to share the current news to everyone, it still seems to have taken away our privacy of what content we actually read. To avoid displaying the news on our Facebook page: 1. If you want the feeds to be displayed in your page but not to be shown to public or friends, just select from the options that are listed when you give permission for the Social Reader when you first read a feed. 2. Select Account Settings from the drop down menu on the top right corner of your FB page. Select Apps Tab which is available in the left side of the page. Here you can change the App Settings or completely delete the App. 3. You can also block Social Reader and other applications’ feeds that are read by your friends. In the right corner of the feed, click the drop-down icon and select “Hide all by ‘Application’” option. By selecting this, you would not be able to see any feeds from your friends too. 4. If you are intrigued by the feeds, you can just copy the title in your search engine and then read directly from their sites. This will not list the feed in your Facebook page.

    Read the article

  • Cannot ping router with a static IP assigned?

    - by Uriah
    Alright. I am running Ubuntu LTS 12.04 and am trying to configure a local caching/master DNS server so I am using Bind9. First, here are some things via default DHCP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The primary network interface - STATIC #auto eth0 #iface eth0 inet static # address 192.168.2.113 # netmask 255.255.255.0 # network 192.168.2.0 # broadcast 192.168.2.255 # gateway 192.168.2.1 # dns-search uclemmer.net # dns-nameservers 192.168.2.113 8.8.8.8 /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 search uclemmer.net ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.103 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1067 errors:0 dropped:0 overruns:0 frame:0 TX packets:2504 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:153833 (153.8 KB) TX bytes:214129 (214.1 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:915 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:71643 (71.6 KB) TX bytes:71643 (71.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. 64 bytes from 192.168.2.1: icmp_req=1 ttl=64 time=0.368 ms 64 bytes from 192.168.2.1: icmp_req=2 ttl=64 time=0.224 ms 64 bytes from 192.168.2.1: icmp_req=3 ttl=64 time=0.216 ms 64 bytes from 192.168.2.1: icmp_req=4 ttl=64 time=0.237 ms --- 192.168.2.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.216/0.261/0.368/0.063 ms ping -c 4 google.com PING google.com (74.125.134.102) 56(84) bytes of data. 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=1 ttl=48 time=15.1 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=2 ttl=48 time=11.4 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=3 ttl=48 time=11.6 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=4 ttl=48 time=11.5 ms --- google.com ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 11.488/12.465/15.118/1.537 ms ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.103 As you can see, with DHCP everything seems to work fine. Now, here are things with static IP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # The primary network interface - STATIC auto eth0 iface eth0 inet static address 192.168.2.113 netmask 255.255.255.0 network 192.168.2.0 broadcast 192.168.2.255 gateway 192.168.2.1 dns-search uclemmer.net dns-nameservers 192.168.2.1 8.8.8.8 I have tried dns-nameservers in various combos of *.2.1, *.2.113, and other reliable, public nameservers. /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 nameserver 8.8.8.8 search uclemmer.net Obviously, when I change the nameservers in the /etc/network/interfaces file, the nameservers change here too. ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.113 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1707 errors:0 dropped:0 overruns:0 frame:0 TX packets:2906 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:226230 (226.2 KB) TX bytes:263497 (263.4 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:985 errors:0 dropped:0 overruns:0 frame:0 TX packets:985 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:78625 (78.6 KB) TX bytes:78625 (78.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. --- 192.168.2.1 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms ping -c 4 google.com ping: unknown host google.com Lastly, here are my bind zone files: /etc/bind/named.conf.options cat /etc/bind/named.conf.options options { directory "/etc/bind"; // // // query-source address * port 53; notify-source * port 53; transfer-source * port 53; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { // My local 192.168.2.113; // Comcast 75.75.75.75; 75.75.76.76; // Google 8.8.8.8; 8.8.4.4; // DNSAdvantage 156.154.70.1; 156.154.71.1; // OpenDNS 208.67.222.222; 208.67.220.220; // Norton 198.153.192.1; 198.153.194.1; // Verizon 4.2.2.1; 4.2.2.2; 4.2.2.3; 4.2.2.4; 4.2.2.5; 4.2.2.6; // Scrubit 67.138.54.100; 207.255.209.66; }; // // // //allow-query { localhost; 192.168.2.0/24; }; //allow-transfer { localhost; 192.168.2.113; }; //also-notify { 192.168.2.113; }; //allow-recursion { localhost; 192.168.2.0/24; }; //======================================================================== // If BIND logs error messages about the root key being expired, // you will need to update your keys. See https://www.isc.org/bind-keys //======================================================================== dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local cat /etc/bind/named.conf.local // // Do any local configuration here // // Consider adding the 1918 zones here, if they are not used in your // organization //include "/etc/bind/zones.rfc1918"; zone "example.com" { type master; file "/etc/bind/zones/db.example.com"; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.2.168.192.in-addr.arpa"; /etc/bind/zones/db.example.com cat /etc/bind/zones/db.example.com ; ; BIND data file for example.com interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 192.168.2.113 @ IN AAAA ::1 @ IN MX 10 yossarian.example.com. ; yossarian IN A 192.168.2.113 router IN A 192.168.2.1 printer IN A 192.168.2.200 ; ns01 IN CNAME yossarian.example.com. www IN CNAME yossarian.example.com. ftp IN CNAME yossarian.example.com. ldap IN CNAME yossarian.example.com. mail IN CNAME yossarian.example.com. /etc/bind/zones/db.2.168.192.in-addr.arpa cat /etc/bind/zones/db.2.168.192.in-addr.arpa ; ; BIND reverse data file for 2.168.192.in-addr interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 255.255.255.0 ; 113 IN PTR yossarian.example.com. 1 IN PTR router.example.com. 200 IN PTR printer.example.com. ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.113 I can SSH in to the machine locally at *.2.113 or at whatever address is dynamically assigned when in DHCP "mode". *2.113 is in my router's range and I have ports open and forwarding to the server. Pinging is enabled on the router too. I briefly had a static configuration working but it died after the first reboot. Please let me know what other info you might need. I am beyond frustrated/baffled.

    Read the article

  • Hosting WCF over internet

    - by user1876804
    I am pretty new to exposing the WCF services hosted on IIS over internet. I will be deploying a WCF service over IIS(6 or 7) and would like to expose this service over the internet. This will be hosted in a corporate network having firewall, I want this service to be accessible over the internet(should be able to pass through the firewall) I did some research on this and some of the pointers I got: 1. I could use wsHTTPBinding or nettcpbinding (the client is intended to be .net client). Which of the bindings is preferable. 2. To overcome the corporate I came across DMZ server, what is the purpose of this and do I really need to use this). 3. I will be passing some files between the client and server, and the client needs to know the progress of the processing on server and the end result. I know this is a very broad question to ask, but could anyone give me pointers where I could start on this and what approach to take for this problem.

    Read the article

  • How to diagnose network speed drops

    - by Luis Alvarado
    Here is the image of System Monitor first: The graph shows the cycle the connection goes through. After 10 to 15 seconds it drops to 0 KB/S, then goes up to the Max speed (120 KB/S) then it repeats. dmesg shows the following during that time: [ 6066.757211] wlan0: send auth to 00:26:5a:b5:05:7b (try 1/3) [ 6066.804405] wlan0: authenticated [ 6066.804578] rt2800pci 0000:02:01.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6066.805016] wlan0: associate with 00:26:5a:b5:05:7b (try 1/3) [ 6066.809218] wlan0: RX AssocResp from 00:26:5a:b5:05:7b (capab=0x431 status=0 aid=1) [ 6066.809581] wlan0: associated [ 6066.810203] bridge-eth0: disabling the bridge on dev down [ 6066.810239] bridge-eth0: down [ 6066.810254] bridge-eth0: detached [ 6066.810309] /dev/vmnet: open called by PID 1679 (vmnet-bridge) [ 6066.810322] /dev/vmnet: hub 0 does not exist, allocating memory. [ 6066.810355] /dev/vmnet: port on hub 0 successfully opened [ 6066.810366] bridge-wlan0: device is wireless, enabling SMAC [ 6066.810369] bridge-wlan0: up [ 6066.810372] bridge-wlan0: attached [ 6067.010285] userif-2: sent link down event. [ 6067.010290] userif-2: sent link up event. This also repeats with Wired or Wireless connections. How can I diagnose this changes in the network efficiently.

    Read the article

  • Multiplayer mobile games and coping with high latency

    - by liortal
    I'm currently researching regarding a design for an online (realtime) mobile multiplayer game. As such, i'm taking into consideration that latencies (lag) is going to be high (perhaps higher than PC/consoles). I'd like to know if there are ways to overcome this or minimize the issues of high latency? The model i'll be using is peer-to-peer (using Photon cloud to broadcast messages to all other players). How do i deal with a scenario where a message about a local object's state at time t will only get to other players at *t + HUGE_LAG* ?

    Read the article

  • Cant get internet connection at all on Ubuntu 13.04

    - by James Ellis
    I installed Ubuntu 13.04 alongside my Windows Vista, at the start of installation it doesn't connect to the internet to download updates during installation, also during installation towards the end it removes a lot of stuff that i couldn't catch the details of at the time, it won't find my internet connection even though windows does, i tried using the ethernet cable but it wouldn't pick that up either. So i clicked in Ubuntu... System, network-Browse Internet, then Windows Internet and it said "failed to retrieve share list from server:no such file or directory" how can i get Ubuntu to find my internet???

    Read the article

< Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >