Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 199/1221 | < Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >

• gsm-ussd gives device busy or error (100)

  - by mydoghasworms

  I am using gsm-ussd to try and query my data balance from my 3G modem. When I issue the commands gsm-ussd -m /dev/ttyUSB0 '*188#' or gsm-ussd -m /dev/ttyUSB2 '*188#' I get either "Device or resource busy" (when it is in used and connected) or "Unknown error (100)". My device (Huawei E173) seems to create 3 devices in /dev, namely ttyUSB0, ttyUSB1 and ttyUSB2. None of them work, and ttyUSB1 gives a somewhat different problem, as it just give the following message: * Wrong modem device (use -m <dev>)? * Modem broken (no reaction to AT)

  Read the article

• How to prevent wireless network asking password when briefly out of range

  - by Ian Mackinnon

  When I'm connected to a wireless network from quite far away I sometimes briefly lose the connection. Then Network Manager prompts me to re-confirm the password as if it suspected that was the problem that caused the loss of connection (the password is already filled in in the dialog box). Is this normal behaviour? Can I prevent it from happening and have Network Manager automatically reconnect without the password dialog box when the wireless network comes back into range? I'm using 10.04 (32bit, Gnome) on an Acer Aspire one.

  Read the article

• How to prevent WLAN connection from dropping permanently on a Fritz USB WLAN N stick?

  - by Chris

  I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

  Read the article

• Ubuntu 12.04 connected to wireless network but internet not working

  - by A.J.

  I can connect to my house's wireless network just fine, but when I'm connected I can't browse the web. Firefox starts connecting to a site and then just poops out. This doesn't happen on my roommates' computers (running Windows) or on our 3DSes, so I know it's just my laptop. I already tried sudo dhclient -r sudo dhclient sudo ifconfig eth0 down sudo ifconfig eth0 up Results of a few commands I was asked to run in comments: ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. ^C --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (173.194.33.38) 56(84) bytes of data. --- google.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1006ms nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 88:AE:1D:6B:4E:E7 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off - Device: wlan0 [JUSTICE] ----------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: connected Default: yes HW Address: 1C:65:9D:65:C6:31 Capabilities: Speed: 1 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) HOME-9B18: Infra, 00:26:F3:53:9B:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 34 WPA WPA2 cougdad48 Network: Infra, 60:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 22 WPA2 cougdad48 Guest Network: Infra, 66:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA2 belkin.ade: Infra, 94:44:52:FF:8A:DE, Freq 2457 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 *JUSTICE: Infra, 00:24:01:7B:9F:7E, Freq 2462 MHz, Rate 54 Mb/s, Strength 88 WEP CenturyLink: Infra, B2:B2:DC:8E:E2:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 IPv4 Settings: Address: 192.168.0.11 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 (JUSTICE is my home's network.) ping -c 2 198.168.0.1 PING 198.168.0.1 (198.168.0.1) 56(84) bytes of data. --- 198.168.0.1 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• How to control an Ubuntu PC from another Ubuntu PC over Internet?

  - by Naveen

  There are two Ubuntu PCs called A and B. A and B are connected to the Internet using two separated Internet connections. (In my case, two mobile broadband connections ppp0 x2 ) Each connection has a unique & static public IP address. What I need is to control A computer's cursor, using B computer's mouse, over the Internet. In both computers, I have allowed other users to control my computer in Desktop Sharing preferences, as below: When I try to connect to A from the B using Remmina Remote Desktop Client, it refuses to connect after trying for a while. These are my settings: I expect this to be done from an available open source software, not from TeamViewer. I found this guide harder to understand. Please provide me clear instructions... Thanks for having a look!

  Read the article

• compiling compat-wireless fails at 'make' with 'make: *** [modules] Error 2'

  - by Paul Carter

  Trying to compile the compat-wireless-2012-09-25 driver module, without success. scrips/driver-select alx ; works make ; fails - scripts/Makefile.build:44 ~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: ** No rule to make target '~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile'. Stop. [snip] make: * [modules] Error 2 Device is Atheros AR8161 wired ethernet in a Dell Vostro 3460. I'd be very grateful for assistance in getting this to compile.

  Read the article

• Network icon shows an Internet connection, while ping does not

  - by mushfiq

  I am an Ubuntu user for the last couple of years. Recently facing problem to connect my new laptop into the Internet. I have an ISP connection which provide me a NAT address. I changed all the information in network configuration.The network icon shows it is connected to Internet but when I browse, ping shows no Internet connection. /etc/network/interfaces look like this: auto eth0 iface eth0 inet static address 192.168.100.118(put you internet address provided by the ISP) gateway 192.168.100.1(gateway address) netmask 255.255.255.0 network 192.168.100.0 And when I ping my DNS server IP get the reply from DNS server. I can not understand the problem,it should be mentioned that I also changed the Physical address of my laptop for using the existing connection. In windows the connection is working fine. Any suggestion in this question will help me a lot. Thanks in advance.

  Read the article

• Connect WPA networks using Broadcom BCM4315

  - by Natim

  I just installed Ubuntu 14.04 LTS on my HP computer I installed the BCM43 driver I used @Wild Man script to get you some informations: wget -N -t 5 -T 10 http://dl.dropbox.com/u/57264241/wireless_script && chmod +x wireless_script && ./wireless_script Here: http://paste.lolnet.org/paste/kOil1BvT#psOHgxeF As you can see on the file, everything looks good, WEP,WPA,WPA2 but my wifi which is a WPA-PSK password doesn't appears on the network list. Do you have any idea of what could be wrong?

  Read the article

• Connectify Dispatch: Link All Your Network Connections into a Super Pipeline

  - by Jason Fitzpatrick

  Connectify Dispatch is a network management tool that takes all the connections around you–Ethernet, Wi-Fi nodes, even 3G/4G cellular connections–and combines them into one giant data pipeline. At its most simple, Connectify Dispatch takes all the network inputs available to your computer (be those connections hard-line Ethernet, Wi-Fi nodes, or cellular connections) and merges the separate data connections seamlessly into one master connection. If any of the connections should falter (like your 3G reception goes out), Connectify automatically shifts the data to other available networks without any interruption. In addition you can specify which network Connectify should favor with connection prioritization; perfect for using your cellular connection without breaking through your data cap for the month right away. Hit up the link below to read more about Connectify Dispatch and the companion app Connectify Hotspot. Connectify Dispatch Secure Yourself by Using Two-Step Verification on These 16 Web Services How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot

  Read the article

• Bash script won't stay open in background after running through while

  - by jfreak53

  I can't get the following bash script to stay open after the first message is received from NC: #!/bin/bash port=3333 nc -l $port | while read msg; do notify-send Alert "$msg"; done After the first message it exits. I want it to stay open and continue monitoring for new messages from NC. I know that if I launch nc -l port without the while loop it stays open and I can chat away between the two connections even disconnect from the connected host. I am sending the message using: echo 'done' | nc IP port

  Read the article

• Connectify Dispatch Links Multiple Network Nodes Into a Mega Connection

  - by Jason Fitzpatrick

  Connectify Dispatch wants to change the way you interact with the networks around you by making it dead simple to mesh all available Wi-Fi, Cellular, and Ethernet connections into a massive and stable pipeline. Dispatch makes it open-and-click easy to hook up multiple Wi-Fi nodes, your cellphone, and even Ethernet connections into a single blended connection. While the video above gives a great overview of the process, check out the video below to see it in real world action: The project is currently in the last phase of KickStarter funding, so now is a great time to score Connectify Dispatch at a steep discount–pledging as little as $10 to fund the project, for example, scores you 50% of a 6-month Pro license. Hit up the link below to read more about the project, check the KickStarter status, and see all the neat features in the development pipeline. Dispatch: The Internet, Faster. [KickStarter] HTG Explains: What The Windows Event Viewer Is and How You Can Use It HTG Explains: How Windows Uses The Task Scheduler for System Tasks HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows?

  Read the article

• Implementing the transport layer for a SIP UAC

  - by Jonathan Henson

  I have a somewhat simple, but specific, question about implementing the transport layer for a SIP UAC. Do I expect the response to a request on the same socket that I sent the request on, or do I let the UDP or TCP listener pick up the response and then route it to the correct transaction from there? The RFC does not seem to say anything on the matter. It seems that especially using UDP, which is connection-less, that I should just let the listeners pick up the response, but that seems sort of counter intuitive. Particularly, I have seen plenty of UAC implementations which do not depend on having a Listener in the transport layer. Also, most implementations I have looked at do not have the UAS receiving loop responding on the socket at all. This would tend to indicate that the client should not be expecting a reply on the socket that it sent the request on. For clarification: Suppose my transport layer consists of the following elements: TCPClient (Sends Requests for a UAC via TCP) UDPClient (Sends Requests for a UAC vid UDP) TCPSever (Loop receiving Requests and dispatching to transaction layer via TCP) UDPServer (Loop receiving Requests and dispatching to transaction layer via UDP) Obviously, the *Client sends my Requests. The question is, what receives the Response? The *Client waiting on a recv or recvfrom call on the socket it used to send the request, or the *Server? Conversely, the *Server receives my requests, What sends the Response? The *Client? doesn't this break the roles of each member a bit?

  Read the article

• ralink rt2860 not working anymore in ubuntu 12.10

  - by greenit

  I just upgraded from Ubuntu 12.04 to 12.10, however, my network card is not working anymore... When i had 12.04 installed, i just had to download the driver from Ralink, go to the directory and enter these commands: $ make $ sudo make install and the network card worked... now, when I want to do this in ubuntu 12.10, it seems like it works, but it doesn't. I can enable the module, it recognizes the network card, but i am unable to connect to any wireless network... How can i get my wireless card working again? If any1 knows a solution, please tell it to me, thx in advance

  Read the article

• Ask HTG: Disabling Windows Startup Programs, Using DNS Names on Your Home Network, and Restoring a Vintage Keyboard

  - by Jason Fitzpatrick

  Once  a week we round up some of the answers we’ve sent out to readers and share them with everyone. This week we’re looking at removing programs from the Windows startup routine, using DNS names on the local network, and restoring a vintage keyboard. HTG Explains: Do You Really Need to Defrag Your PC? Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone How To Migrate Windows 7 to a Solid State Drive

  Read the article

• No client internet access when setting up these iptables rules

  - by Siriss

  I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

  Read the article

• Cannot authenticate to SBS 2003

  - by Lerp

  I am trying to connect my machine to my work's entirely windows network and I am having a few issues: Whenever I try to access the server, the authentication dialog just keeps popping back up. I cannot connect to the printers (it says connecting to device failed) I have tried setting up samba, winbind, kerberos, likewise open all to no avail. I have a feeling I am just setting them up wrong. My nautilus shows this when I go to Network Windows Network MASTERMAGNETS I can ping both MASTERMAGNETS.LOCAL and 192.168.0.2 after modifying my /etc/hosts james@jamesmaddison:~$ cat /etc/hosts 127.0.0.1 localhost jamesmaddison 192.168.0.2 MASTERMAGNETS.LOCAL 192.168.0.50 Sharp-Printer # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters I believe that's the correct domain (not sure if that's the correct term) as when I do nslookup MASTERMAGNETS.LOCAL I get the following: james@jamesmaddison:~$ nslookup MASTERMAGNETS.LOCAL Server: 192.168.0.2 Address: 192.168.0.2#53 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.3 Name: MASTERMAGNETS.LOCAL Address: 192.168.0.2 It all worked fine before I reinstalled Ubuntu and now I just cannot get access to the server. All help is appreciated, I need to get this working or I fear I will be forced to develop in a windows environment :(

  Read the article

• You made it through the Interview, Now What?

  - by Jonathan Kehayias

  This is somewhat of a continuation post to my previous blog post, “Some thoughts on Interviweing…” .  Now that you survived the interview process, what do you do?  This is a common area of discomfort for people interviewing for  any kind of job, not just positions dealing with SQL Server.  In this post I’d like to focus on a topic that I like to refer to as “Post Interview Etiquette” and how it might impact your ability to get hired for a position.  Whether or not to follow-up...(read more)

  Read the article

• Printing to a printer connected to a wireless router

  - by mspencer

  I have a Netgear WNDR4500 wireless router which allows me to print wirelessly to a printer connected to it via a USB cable. However, the software used to print to it only works for Windows and OS X. I've seen the question Printing to a printer attached to a network USB hub, and tried the instructions it gave using my router's IP address, but when I print a test page it says copying data then says printer is in use. In the printer queue window it says not connected. How can I print to the printer using Ubuntu? Thanks.

  Read the article

• Ubuntu systematically losing wired connection

  - by Lukasz Baczynski

  I'm working on 11.10 for few recent days, everything was working perfect until today. Updated ubuntu (some certs were updates as far as i remember) and from this time, wired network stops working randomly and systematically. (All other pcs/macs work fine) From 192.168.0.9 icmp_seq=25 Destination Host Unreachable From 192.168.0.9 icmp_seq=26 Destination Host Unreachable From 192.168.0.9 icmp_seq=27 Destination Host Unreachable From 192.168.0.9 icmp_seq=28 Destination Host Unreachable From 192.168.0.9 icmp_seq=29 Destination Host Unreachable From 192.168.0.9 icmp_seq=30 Destination Host Unreachable From 192.168.0.9 icmp_seq=31 Destination Host Unreachable 64 bytes from 192.168.0.1: icmp_req=32 ttl=64 time=1003 ms 64 bytes from 192.168.0.1: icmp_req=33 ttl=64 time=0.496 ms 64 bytes from 192.168.0.1: icmp_req=34 ttl=64 time=0.576 ms 64 bytes from 192.168.0.1: icmp_req=35 ttl=64 time=0.522 ms 64 bytes from 192.168.0.1: icmp_req=36 ttl=64 time=0.624 ms 64 bytes from 192.168.0.1: icmp_req=37 ttl=64 time=0.625 ms 64 bytes from 192.168.0.1: icmp_req=38 ttl=64 time=0.555 ms It'll work for 20 seconds then it'll stop working for 10-30sec and so on. I've tried setting my router to give static IPs, it doesn't help. NOTHING has been changed since yesterday beside the package update... Here are other settings that may be useful: baka@baka-PC:~/Private/projects/wduk$ lspci -nnk | grep -iA2 net 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432] Kernel driver in use: r8169 baka@baka-PC:~/Private/projects/wduk$ ifconfig -a eth0 Link encap:Ethernet HWaddr **Removed MAC address** inet addr:192.168.0.9 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:fe0a:85b2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6400 errors:0 dropped:6400 overruns:0 frame:6400 TX packets:7085 errors:0 dropped:107 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4191983 (4.1 MB) TX bytes:886881 (886.8 KB) Interrupt:72 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2522 errors:0 dropped:0 overruns:0 frame:0 TX packets:2522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1070130 (1.0 MB) TX bytes:1070130 (1.0 MB) baka@baka-PC:~/Private/projects/wduk$ cat /etc/resolv.conf # Generated by NetworkManager nameserver 8.8.8.8 thanks for help

  Read the article

• Why would accessing photos over a network be a problem for Digikam?

  - by Shedeki

  Digikam has always worked nicely for me. I recently setup a Synology DiskStation (DS212+) and moved all my pictures to it, keeping them in an encrypted folder. I mount that folder using cifs, as some bug prevents eCryptfs and NFS from working together. This has led Digikam to being incredibly slow. Startup takes a very long time (several minutes for 41779 items, 123.8GB) but worse is how long it takes Digikam to write files. I like using Digikams import feature to copy new images from my camera to the hard drive because it checks for duplicates as well as creating a clear folder structure according to the dates the images were taken. Since I moved to using the network drive Digikam takes about 5 to 10 times as long to import photos than it did before. Saving modified or converted images takes equally long. What I am looking for is a way to help Digikam speed things up or an alternative piece of software (I have never liked Digikam being so very much KDEish…). There are just so many features that only Digikam seems to combine, e.g.: Batch processing. Respects existing folder structure. Does not mess up files for other applications. *.NEF support. Caches thumbnails in a clean way.

  Read the article

• Forward TCP Connections with Iptables

  - by opc0de

  I receive connections to my server from several ip addresses I want to route these connections just like rinetd does but based on the ip the connection is coming from to connect to a specified host. Just like this: IP 10.10.12.1 => CONNECTS TO MY SERVER => MY SERVER REDIRECTS IT TO 82.12.12.1 IP 10.10.12.2 => CONNECTS TO MY SERVER => MY SERVER REDIRECTS IT TO 81.121.12.10 etc Is it possible or do I need to write my own daemon to achieve this functionality ?

  Read the article

• Oracle Linux 6 update 3

  - by wcoekaer

  Oracle Linux 6.3 channels are now available online http://public-yum.oracle.com repositories. Both base channels and latest channels are available (for free for everyone) http://linux.oracle.com repositories. Behind our customer portal but effectively the same content. Source RPMs (.srpm) are being uploaded to http://oss.oracle.com/ol6/SRPMS-updates. OL6.3 contains UEK2 kernel-uek-2.6.39-200.24.1. The source rpm is in the above location but our public GIT repository will be synced up shortly as well at https://oss.oracle.com/git/?p=linux-uek-2.6.39.git;a=summary. Unlike some others, of course, complete source, complete changelog, complete checkin history, both mainline and our own available. No need to go assemble things from a website manually. Another cool thing coming up is a boot iso for OL6.3 that boots up uek (2.6.39-200.24.1) as install kernel and uses btrfs as the default filesystem for installation. So latest and greatest direct access to btrfs, a modern well-tested, current kernel, freely available. Enjoy. Since it takes a few days for our ISOs to be on http://edelivery.oracle.com/linux, I mirrored them on my own server :http://mirrors.wimmekes.net/pub/OracleLinux/

  Read the article

• How can i get latency when using Game Center?

  - by Freddy

  I'm pretty new to network programming. Basically I'm using game center for making a relatively simple iPhone game using Game-center p2p. However i'm now working on a algorithm to improve the multiplayer performance. But, I need to know how long it took for a package to travel from one device to the another device (latency) for the algorithm to work good. As for now, I have solved the problem by sending a double with time interval since 1970 in the package and then I compare it with the time at the other device. However I have heard that the NSDate methods is connected to the internet, which also will cause latency so the time interval would not be perfectly correct. What is the ideal way to check for how long it take for a package to be sent?

  Read the article

• Copy hangs in local network

  - by umpirsky

  I want to copy files from one Ubuntu system to another.They are both in local wireless network. I shared entire home dir on one, and tried to copy some files to another. It works for some time and then it just hangs at some point. I use Nautilus to copy files. Here is the example screenshot, it just hangs like this: After I cancel, Nautilus icon in lauchbar keeps progress bar, so I guess there is some problem. What can be the problem?

  Read the article

< Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >