Search Results

Search found 1080 results on 44 pages for 'connectivity'.

Page 2/44 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Intermittent internet connectivity

  - by Rob Oplawar

  UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

  Read the article

• SQL Server Connectivity Portal

  - by Enrique Lima

  We all love one stop portals :-) Browsing around MSDN I came across this for connectivity, yes, a one stop portal, find info on connecting using a variety of technologies and good guides. http://msdn.microsoft.com/en-us/sqlserver/connectivity.aspx

  Read the article

• Troubleshooting SQL Azure Connectivity

  - by kaleidoscope

  Technorati Tags: Rituraj,Connectivity Issues with SQL Azure Troubleshooting SQL Azure Connectivity How to resolve some of the common connectivity error messages that you would see while connecting to SQL Azure A transport-level error has occurred when receiving results from the server. (Provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) System.Data.SqlClient.SqlException: Timeout expired.  The timeout period elapsed prior to completion of the operation or the server is not responding. The statement has been terminated. An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections Error: Microsoft SQL Native Client: Unable to complete login process due to delay in opening server connection. A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond. Some troubleshooting tips a) Verify Azure Firewall Settings and Service Availability     Reference: SQL Azure Firewall - http://msdn.microsoft.com/en-us/library/ee621782.aspx b) Verify that you can reach our Virtual IP     Reference: Telnet Troubleshooting Guide - http://technet.microsoft.com/en-us/library/cc753360(WS.10).aspx    Reference: How to Use TRACERT to Troubleshoot TCP/IP Problems in Windows - http://support.microsoft.com/kb/314868 c) Windows Firewall on the local machine     Frequently Asked Questions - http://msdn.microsoft.com/en-us/library/bb736261(VS.85).aspx     Reference: Windows Firewall with Advanced Security Getting Started Guide - http://technet.microsoft.com/en-us/library/cc748991(WS.10).aspx d) Other Firewall products     Reference: http://www.whatismyip.com/ e) Generate a Network Trace using Microsoft Network Monitor tool    Reference: How to capture network traffic with Network Monitor - http://support.microsoft.com/kb/148942 f) SQL Azure Denial of Service (DOS) Guard SQL Azure utilizes techniques to prevent denial of service attacks. If your connection is getting reset by our service due to a potential DOS attack you would  be able to see a three way handshake established and then a RESET in your network trace.

  Read the article

• Internet Connectivity Indicicator on Unity

  - by Sathish

  How can I check whether my internet connection is active on Ubuntu. If I am connected to a wired or wi-fi network, the indicator applet shows that I'm connected. But there is now way to find out the internet is working or not. I have some problem in my internet connectivity and I frequently lose my connection. I found this link is useful Internet connectivity indicator applet But I don't know that where should I use this code! #!/bin/bash if ping -c 1 -W 2 google.com > /dev/null; then echo "Up" else echo "Down" fi

  Read the article

• Troubleshooting loss of network connectivity in Windows 2003 - What else to check?

  - by Benny

  We are facing a weird problem in our data center. Our Backup server (running EMC Networker) loses network connection every alternate day around 3:00 AM (Backup schedule starts at midnight). After 2 hours of outage, the network connectivity recovers automatically and back to normal. What we observed: It is unlikely to be network issue, since it is directly connected to server farm switch (layer 2 connection without any intermediate hops). Further, the server is connected to two different switches for Load balancing using Broadcomm Teaming. a) If it were a switch related issue it is unlikely that both the network ports go down, since they are connected to different switch. b) A possibility Vlan wide issue is also ruled out since other devices in the same Vlan are fine. c) Switch interface status is always up. But there are lot of packet drops during the outage period - Can be attributed to high interface utilization of the backup server (near 100%) d) Connectivity is restored without any change on network. Next suspect is resource utilization on Windows server. Both CPU and Memory have rarely exceeded 80%, but NIC card utilization is alarmingly high (near 100%) Not really sure how to investigate this?

  Read the article

• Why do we ping the IP 4.2.2.2 to test connectivity?

  - by gnavi

  For as long as I can remember, I've always used the IP 4.2.2.2 when testing network connectivity using ping. What is significant about this IP, and when did this practice start?

  Read the article

• SharePoint 2010 Video - Business Connectivity Services

  - by Sahil Malik

  Ad:: SharePoint 2007 Training in .NET 3.5 technologies (more information). The latest DNRTV episode on SharePoint 2010 Business Connectivity Services is now online. This is a video we (Carl and I) had recorded back in April 2010, and is a sneak peak to the SharePoint 2010 DVD that is finally on sale. Hope you like both. Comment on the article ....

  Read the article

• Ultrabooks and projectors: is there any connectivity issue due to low power on video output? [closed]

  - by sergey

  I need to buy a new laptop for my wife. She travels a lot and I was thinking about an ultrabook (1.5-2 kg). However she says that ultrabooks have problems connecting to projectors. At least some of her colleagues could not connect their ultrabooks to projectors due to “low output issues”. She is in-company consultant and trainer and for her “be able to connect to any client projector” requirement is must. Thus my doubts are: Is this problem well known? Is there any chance to assure connectivity to projector (by checking some specification before buy, etc)?

  Read the article

• vb.net and mysql connectivity [closed]

  - by kalpana

  I have used adodb using odbc database connectivity for connecting vb.net to mysql. I have fetched table values into recordset. I want to fetch only one column values (for example, table name-login, column name-password and values in password column are "manage","sales","general"). I want to fetch these values in text boxes. I have written code but it's not working. Dim conn As New ADODB.Connection Dim res As New ADODB.Recordset conn.Open("test", "root", "root") res = conn.Execute("select password from login") textbox1.text=res(0).value textbox2.text=res(1).value textbox3.text=res(2).value I am getting data in textbox1 but other data is not getting inserted into textbox2 and textbox3..I am getting error i.e (1) Item cannot be found in the collection corresponding to the requested name or ordinal.

  Read the article

• Upgrade a Retro Corded Mouse with Wireless Bluetooth Connectivity

  - by Jason Fitzpatrick

  If there’s a beloved retro mouse gathering dust in your office closet for want of wireless connectivity, this detailed tutorial will guide you through upgrading the guts to turn your corded mouse into a Bluetooth model. If you’re handy with a soldering iron and not afraid to hack apart the guts of a modern but inexpensive Bluetooth mouse, you should have no trouble digging right into this project. The end result is a modern mouse packed inside the casing of your old mouse–same old look and feel, brand new engine inside. Hit up the link below to check out the full tutorial. Retro Wireless Apple Mouse [via Lifehacker] HTG Explains: Is ReadyBoost Worth Using? HTG Explains: What The Windows Event Viewer Is and How You Can Use It HTG Explains: How Windows Uses The Task Scheduler for System Tasks

  Read the article

• Internet connectivity issues

  - by Fishies

  I'm on 12.04, I upgraded a month ago from Windows 7 on my Sony VAIO. Everything is great except after the upgrade, I encountered Internet connectivity issues. When browsing the web or loading videos, my Internet will stop working in the middle and come back after a period of 30 seconds to 2 minutes or sometimes it just won't and I'll have to disconnect and re-connect to the network. I've noticed the issue when sending e-mails as well, they just won't send at all. It says sending request and the circle keeps spinning slowly until I get to a page where it says the page wouldn't load and gives me the reason DNS error. I tried setting OpenDNS as my DNS provider but that didn't help.

  Read the article

• Troubleshooting wireless network connectivity

  - by taserian

  I'm currently running Ubuntu 10.10, and I'm running into trouble keeping my wireless connection alive. After rebooting, I get about 5-10 minutes of a good speed connection; afterwards, the connection just zeroes out. I've gotten around to stirring up a shell script that gives me another 10 minutes or so of connectivity. Script contents below: #! /bin/bash sudo ifconfig wlan0 up echo "Enabling wireless device . . ." sleep 5 sudo iwconfig wlan0 essid MyNetworkName echo "Connecting to network. . ." sleep 10 sudo dhclient wlan0 echo "Getting IP address. . ." sleep 5 echo "Done. Closing window. . ." sleep 5 Shortly after running the line "sudo iwconfig wlan0 essid MyNetworkName" from the script, I notice the speed pick up. Other computers in my home running Windows XP are not affected by this problem, so all indications point to my Ubuntu machine. Does anyone have any pointers as to how to resolve this?

  Read the article

• Lost connectivity after configuring multiple network adapters on separate networks

  - by Dave Long

  I am trying to setup an Ubuntu hosting server, currently just for development, and the server has two NICs, each sitting on a different network. eth0 is on 192.168.200.* and eth1 is on 192.168.101.* and each one has a static IP. eth0 is the public facing NIC card and eth1 is strictly for internal access to the server. I initially only setup eth0 and added the eth1 card when I needed it. eth0 was working find until I added eth1, now, can't get any connectivity on eth0 unless I pull eth1 out of the box. The configuration on each system is as follows: auto eth0 iface eth0 inet static address 192.168.200.94 netmask 255.255.255.0 network 192.168.200.0 broadcast 192.168.200.255 gateway 192.168.200.253 auto eth1 iface eth1 inet static address 192.168.101.64 netmask 255.255.255.0 network 192.168.101.0 broadcast 192.168.101.255 gateway 192.168.101.254 Again eth0 worked fine until I added eth1. I have seen this happen with Windows servers if you have a Default Gateway setup for both NICs, but I am not sure if this works the same on Ubuntu. My resolv.conf file looks like so: nameserver 192.168.101.59 nameserver 192.168.101.58 domain domain.local search domain.local Per request here is the Routing table 192.168.101.0 * 255.255.255.0 U 0 0 0 eth1 192.168.200.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.101.254 0.0.0.0 UG 100 0 0 eth1 default 192.168.200.253 0.0.0.0 UG 100 0 0 eth0

  Read the article

• Computer Says No: Mobile Apps Connectivity Messages

  - by ultan o'broin

  Sharing some insight into connectivity messages for mobile applications. Based on some recent ethnography done my myself, and prompted by a real business case, I would recommend a message that: In plain language, briefly and directly tells the user what is wrong and why. Something like: Cannot connect because of a network problem. Affords the user a means to retry connecting (or attempts automatically). Mobile context of use means users use anticipate interruptibility and disruption of task, so they will try again as an effective course of action. Tells the user when connection is re-established, and off they go. Saves any work already done, implicitly. (Bonus points on the ADF critical task setting scale) The following images showing my experience reading ADF-EMG Google Groups notification my (Android ICS) Samsung Galaxy S2 during a loss of WiFi give you a good idea of a suitable kind of messaging user experience for mobile apps in this kind of scenario. Inline connection lost message with Retry button Connection re-established toaster message The UX possible is dependent on device and platform features, sure, so remember to integrate with the device capability (see point 10 of this great article on mobile design by Brent White and Lynn Hnilo-Rampoldi) but taking these considerations into account is far superior to a context-free dumbed down common error message repurposed from the desktop mentality about the connection to the server being lost, so just "Click OK" or "Contact your sysadmin.".

  Read the article

• 2D Grid Map Connectivity Check (avoiding stack overflow)

  - by SombreErmine

  I am trying to create a routine in C++ that will run before a more expensive A* algorithm that checks to see if two nodes on a 2D grid map are connected or not. What I need to know is a good way to accomplish this sequentially rather than recursively to avoid overflowing the stack. What I've Done Already I've implemented this with ease using a recursive algorithm; however, depending upon different situations it will generate a stack overflow. Upon researching this, I've come to the conclusion that it is overflowing the stack because of too many recursive function calls. I am sure that my recursion does not enter an infinite loop. I generate connected sets at the beginning of the level, and then I use those connected sets to determine connectivity on the fly later. Basically, the generating algorithm starts from left-to-right top-to-bottom. It skips wall nodes and marks them as visited. Whenever it reaches a walkable node, it recursively checks in all four cardinal directions for connected walkable nodes. Every node that gets checked is marked as visited so they aren't handled twice. After checking a node, it is added to either a walls set, a doors set, or one of multiple walkable nodes sets. Once it fills that area, it continues the original ltr ttb loop skipping already-visited nodes. I've also looked into flood-fill algorithms, but I can't make sense of the sequential algorithms and how to adapt them. Can anyone suggest a better way to accomplish this without causing a stack overflow? The only way I can think of is to do the left-to-right top-to-bottom loop generating connected sets on a row basis. Then check the previous row to see if any of the connected sets are connected and then join the sets that are. I haven't decided on the best data structures to use for that though. I also just thought about having the connected sets pre-generated outside the game, but I wouldn't know where to start with creating a tool for that. Any help is appreciated. Thanks!

  Read the article

• Tulsa SharePoint Interest Group - How SharePoint 2010 Business Connectivity Services could change yo

  - by dmccollough

  Bio: Corey Roth is a consultant at Stonebridge specializing in SharePoint solutions in the Oil & Gas Industry. He has ten plus years of experience delivering solutions in the energy, travel, advertising and consumer electronics verticals. Corey has always focused on rapid adoption of new Microsoft technologies including Visual Studio 2010, SharePoint 2010, .NET Framework 4.0, LINQ, and SilverLight. He also contributed greatly to the beta phases of Visual Studio 2005. For his contributions, he was awarded the Microsoft Award for Customer Excellence (ACE). Corey is a graduate of Oklahoma State University. Corey is a member of the .NET Mafia (www.dotnetmafia.com) where he blogs about the latest technology and SharePoint. Abstract: How SharePoint 2010 Business Connectivity Services could change your life - The New BDC How many hours have your wasted building simple ASP.NET applications to do nothing more than simple CRUD operations against a database.  Many tools have made this easier, but now it's so easy, you'll be up and running in minutes.  This session will show you hot easy it is to get started integrating external data from your line of business systems in SharePoint 2010.  You will learn how to register an external content type using SharePoint Designer based upon a database table or web service and then build an external list.  With external lists, you will see how you can perform CRUD operations on your line of business directly from SharePoint without ever having to do manual configuration in XML files.  Finally, we will walk through how to create custom edit forms for your list using InfoPath 2010. Agenda: 6pm - 6:30 Pizza and Mingle - Sponsored by TekSystems 6:30 - 6:45 Announcements 6:45 - 7:45 Presentation! 7:45 - 8:00 Drawings and Door Prizes Location: TCC (Tulsa Community College) Northeast Campus 3727 East Apache Tulsa, OK 74115 918-594-8000 Campus Map | Live | Yahoo | Google | MapQuest Door Prizes: We will be giving away one of each of these: XBox 360 - Halo 3 ODST Telerik Premium Collection ($1300.00 value) ReSharper ($199.00 value) SQLSets ($149.00 value) 64 bit Windows 7 Introducing Windows 7 for Developers Developing Service-Oriented AJAX Applications on the Microsoft Platform Sponsors: Thanks to our sponsors: TekSystems - Thanks for purchasing the Pizza for our meetings. ISOCentric - Thanks for providing us hosting for the groups web site. Tulsa Community College - Thanks for providing us a place to have our meetings. NEVRON - Thanks for providing us prizes to give away. INETA.org - For allowing us to be a Charter Member and providing awesome Speakers! PERPETUUM Software - Thanks for providing us prizes to give away. Telerik - Thanks for providing us prizes to give away. GrapeCity - Thanks for providing us prizes to give away. SQLSets - Thanks for providing us prizes to give away. K2 - Thanks for providing us prizes to give away. Microsoft - For providing us with a lot of support and product giveaways! Orielly books - For providing us with books and discounts. Wrox books - For providing us with books and discounts. Have any special requests? Let us know at this link: http://tinyurl.com/lg5o38. RSVP for this month's meeting by responding to this thread: http://tinyurl.com/yafkzel . (Must be logged in to the site) Be SURE to RSVP no later than Noon on April 12th and you will get an extra entry for the prize drawings! So, do it now, before you forget and miss out! Show up for the first time or bring a new buddy and you both get TWO extra entries!

  Read the article

• Internet Connectivity... Help please!

  - by James

  Hi. My Laptop is having trouble connecting to my wireless router. Other laptops are using the wireless, but it's not reached capacity. The laptop recognises (with a strong signal) that there is wireless internet, and I can connect via the router with a cable because this happens automatically. My problem is this... When I click "connect" (for example in the network and sharing centre), the dialogue box closes and nothing else happens - as though "connect" is being read as "exit". I am running Vista on a Toshiba Satellite Pro P300. Any help would be very much appreciated, Thanks

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  Hi: I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• Manage SQL Server Connectivity through Windows Azure Virtual Machines Remote PowerShell

  - by SQLOS Team

  Manage SQL Server Connectivity through Windows Azure Virtual Machines Remote PowerShell Blog This blog post comes from Khalid Mouss, Senior Program Manager in Microsoft SQL Server. Overview The goal of this blog is to demonstrate how we can automate through PowerShell connecting multiple SQL Server deployments in Windows Azure Virtual Machines. We would configure TCP port that we would open (and close) though Windows firewall from a remote PowerShell session to the Virtual Machine (VM). This will demonstrate how to take the advantage of the remote PowerShell support in Windows Azure Virtual Machines to automate the steps required to connect SQL Server in the same cloud service and in different cloud services.  Scenario 1: VMs connected through the same Cloud Service 2 Virtual machines configured in the same cloud service. Both VMs running different SQL Server instances on them. Both VMs configured with remote PowerShell turned on to be able to run PS and other commands directly into them remotely in order to re-configure them to allow incoming SQL connections from a remote VM or on premise machine(s). Note: RDP (Remote Desktop Protocol) is kept configured in both VMs by default to be able to remote connect to them and check the connections to SQL instances for demo purposes only; but not actually required. Step 1 – Provision VMs and Configure Ports   Provision VM1; named DemoVM1 as follows (see examples screenshots below if using the portal):   Provision VM2 (DemoVM2) with PowerShell Remoting enabled and connected to DemoVM1 above (see examples screenshots below if using the portal): After provisioning of the 2 VMs above, here is the default port configurations for example: Step2 – Verify / Confirm the TCP port used by the database Engine By the default, the port will be configured to be 1433 – this can be changed to a different port number if desired.   1. RDP to each of the VMs created below – this will also ensure the VMs complete SysPrep(ing) and complete configuration 2. Go to SQL Server Configuration Manager -> SQL Server Network Configuration -> Protocols for <SQL instance> -> TCP/IP - > IP Addresses   3. Confirm the port number used by SQL Server Engine; in this case 1433 4. Update from Windows Authentication to Mixed mode   5.       Restart SQL Server service for the change to take effect 6.       Repeat steps 3., 4., and 5. For the second VM: DemoVM2 Step 3 – Remote Powershell to DemoVM1 Enter-PSSession -ComputerName condemo.cloudapp.net -Port 61503 -Credential <username> -UseSSL -SessionOption (New-PSSessionOption -SkipCACheck -SkipCNCheck) Your will then be prompted to enter the password. Step 4 – Open 1433 port in the Windows firewall netsh advfirewall firewall add rule name="DemoVM1Port" dir=in localport=1433 protocol=TCP action=allow Output: netsh advfirewall firewall show rule name=DemoVM1Port Rule Name:                            DemoVM1Port ---------------------------------------------------------------------- Enabled:                              Yes Direction:                            In Profiles:                             Domain,Private,Public Grouping:                             LocalIP:                              Any RemoteIP:                             Any Protocol:                             TCP LocalPort:                            1433 RemotePort:                           Any Edge traversal:                       No Action:                               Allow Ok. Step 5 – Now connect from DemoVM2 to DB instance in DemoVM1 Step 6 – Close port 1433 in the Windows firewall netsh advfirewall firewall delete rule name=DemoVM1Port Output: Deleted 1 rule(s). Ok. netsh advfirewall firewall show  rule name=DemoVM1Port No rules match the specified criteria.   Step 7 – Try to connect from DemoVM2 to DB Instance in DemoVM1  Because port 1433 has been closed (in step 6) in the Windows Firewall in VM1 machine, we can longer connect from VM3 remotely to VM1. Scenario 2: VMs provisioned in different Cloud Services 2 Virtual machines configured in different cloud services. Both VMs running different SQL Server instances on them. Both VMs configured with remote PowerShell turned on to be able to run PS and other commands directly into them remotely in order to re-configure them to allow incoming SQL connections from a remote VM or on on-premise machine(s). Note: RDP (Remote Desktop Protocol) is kept configured in both VMs by default to be able to remote connect to them and check the connections to SQL instances for demo purposes only; but not actually needed. Step 1 – Provision new VM3 Provision VM3; named DemoVM3 as follows (see examples screenshots below if using the portal): After provisioning is complete, here is the default port configurations: Step 2 – Add public port to VM1 connect to from VM3’s DB instance Since VM3 and VM1 are not connected in the same cloud service, we will need to specify the full DNS address while connecting between the machines which includes the public port. We shall add a public port 57000 in this case that is linked to private port 1433 which will be used later to connect to the DB instance. Step 3 – Remote Powershell to DemoVM1 Enter-PSSession -ComputerName condemo.cloudapp.net -Port 61503 -Credential <UserName> -UseSSL -SessionOption (New-PSSessionOption -SkipCACheck -SkipCNCheck) You will then be prompted to enter the password.   Step 4 – Open 1433 port in the Windows firewall netsh advfirewall firewall add rule name="DemoVM1Port" dir=in localport=1433 protocol=TCP action=allow Output: Ok. netsh advfirewall firewall show rule name=DemoVM1Port Rule Name:                            DemoVM1Port ---------------------------------------------------------------------- Enabled:                              Yes Direction:                            In Profiles:                             Domain,Private,Public Grouping:                             LocalIP:                              Any RemoteIP:                             Any Protocol:                             TCP LocalPort:                            1433 RemotePort:                           Any Edge traversal:                       No Action:                               Allow Ok.   Step 5 – Now connect from DemoVM3 to DB instance in DemoVM1 RDP into VM3, launch SSM and Connect to VM1’s DB instance as follows. You must specify the full server name using the DNS address and public port number configured above. Step 6 – Close port 1433 in the Windows firewall netsh advfirewall firewall delete rule name=DemoVM1Port   Output: Deleted 1 rule(s). Ok. netsh advfirewall firewall show  rule name=DemoVM1Port No rules match the specified criteria.  Step 7 – Try to connect from DemoVM2 to DB Instance in DemoVM1  Because port 1433 has been closed (in step 6) in the Windows Firewall in VM1 machine, we can no longer connect from VM3 remotely to VM1. Conclusion Through the new support for remote PowerShell in Windows Azure Virtual Machines, one can script and automate many Virtual Machine and SQL management tasks. In this blog, we have demonstrated, how to start a remote PowerShell session, re-configure Virtual Machine firewall to allow (or disallow) SQL Server connections. References SQL Server in Windows Azure Virtual Machines   Originally posted at http://blogs.msdn.com/b/sqlosteam/

  Read the article

• Database Connectivity Test with UDL File

  - by Ben Griswold

  I bounced around between projects a lot last week.  What each project had in common was the need to validate at least one SQL connection.  Whether you have SQL tools like SSMS installed or not, this is a very easy task if you are aware of the UDL (Universal Data Link) files.  Create a new file and name it anything as long as it has the .udl extension. Open the file, choose a provider: Click Next >> or navigate to the Connection Tab to provide connection information.  Once you provide server and login credentials, the database list will populate.  At this point, you know the connection is valid. but go ahead and click the Test Connection button anyway. On the final tab, you can provide extra connection information like Application Name which can come in handy.  The All tab is beneficial if you want to build a valid connection string to include in your own applications.  If you save the file and then open in Notepad, you’ll find that said connection string: Provider=SQLOLEDB.1;Integrated Security=SSPI;Persist Security Info=False;Initial Catalog=master;Data Source=(local);Application Name=TestApp I hope this tip helps save you some time.  How do you test if you don’t have SSMS installed?

  Read the article

• How to check mysql remote connectivity

  - by Mirage

  I have enable the ips in WHM for remote mysql but still i am not able to connect it. Is there any shell command for mysql which i can type to check the remote connectivity I mean any command to execute on server itself where mysql is installed or Any command to execute of local linux to check connectivity on remote MYsql server OS remote :Centos 5.4 local OS : Ubuntu

  Read the article

• Monitor network connectivity in WP7 apps

  - by Daniel Moth

  Most interesting Windows Phone apps rely on some network service for their functionality. So at some point in your app you may need to know programmatically if there is network connection available or not. For example, the Translator by Moth app relies on the Bing Translation service for translations. When a request for translation (text or voice) is made, the network call may fail. The failure reason is not evident from any of the return results, so I check the connection to see if it is present. Dependent on that, a different message is shown to the user. Before the translation phase is even reached, at the app start up time the Bing service is queried for its list of  languages; in that case I don't want to show the user a message and instead want to be notified when the network is available in order to send the query out again. So for those two requirements (which I imagine are common in other apps) I wrote a simple wrapper MyNetwork static class to the framework APIs: Call once MyNetwork.MonitorNetworkAvailability() method so it monitors the network change At any time check the MyNetwork.IsConnected property to check for network presence Subscribe to its MyNetwork.ConnectionEstablished event Optionally, during debugging use its MyNetwork.ChangeStatus method to simulate a change in network status As usual, there may be better ways to achieve this, but this class works perfectly for my scenarios. You can download the code here: MyNetworks.cs. Comments about this post welcome at the original blog.

  Read the article

• No network connectivity (not wired or wireless) - RT5390

  - by Ben Udy

  I am starting to think I simply need to accept a small loss and sell my new ASUS K73E. Because I really don't enjoy computing when I have to deal with Windough$ and this windows 7 64 bit on my new ASUS is even worse than the old machines with XP. I have written to ASUS and they simply say "We don't support Linux" and while Ralink's website says they do support Linux I can't get anyone to tell me what model Ralink card might be in my machine. Is anyone out there who might be able to give me some useful advice???? Here is the answer to command lspci nn && lsusb && lsmod && rfkill list all: di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 Edit #2 lspci 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c49 (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 02:00.0 Network controller: RaLink Device 5390 03:00.0 Ethernet controller: Atheros Communications Device 1083 (rev c0) lsusb Bus 002 Device 002: ID 8087:0024 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 13d3:5710 IMC Networks Bus 001 Device 002: ID 8087:0024 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Thanks for the suggestion because this gave me a model for Ralink RT5390. I have now gone to Ralink.com and downloaded (via Windows 7) the driver package (it is a bz2 file). I hope I can figure out how to install it. And FYI - I was not able to run su (not authorized?) and dmidecode didn't exist (probably needs to be downloaded BUT no internet yet in Ubuntu)

  Read the article

• Intermittent ethernet connectivity

  - by Amey Jah

  I am facing a weird problem. I am connecting to my dsl modem via ethernet. After booting, sometimes Ubuntu 10.10 does not detect the eth0 card properly or does not connect to the modem. I have made the following observations: My modem is fully on. All indicators are on except ethernet, which is blinking continuously. My network indicator applet informs me that I am connected to modem, but I am not able to browse as it has not established connection with modem. I need to power off and on (restart) the modem several times OR disconnect/connect (via network applet) several times, before the system can establish a connection with the modem. Once it establishes the connection, the ethernet LED (on modem) stops blinking and glows continuously. However, I do not see this problem every time I reboot or start my computer. 3/5 time, it connects to the modem in a single attempt. Friends, I am not able to understand root cause of this problem. Plus I do not know what kind of logs should be attached. If you want any logs please give me command to run, and I will paste the result for you. Note: I ran system testing when above problem happened. Follow this link to download result.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >