Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 203/391 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

  • unable to access a NAT'ed IP via a VPN on Windows 7

    - by crmpicco
    I connect to a range of servers hosted by one provider via a VPN. I can connect to the VPN fine, however when I then go and try and connect to the server(s) it fails. A NAT'ed IP address that has worked up until today, has stopped working either via SSH/SFTP. As you can see below, if I try and ping the IP then it responds with Destination host unreachable, but, for some reason it says the reply is from 192.168.0.8? If it enter this IP address in my browser, I get nothing. Where is this IP coming from and is there any good reason why I cannot access the IP I am trying to ping? C:\Users\crmpicco>ping 172.26.100.x Pinging 172.26.100.x with 32 bytes of data: Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Reply from 192.168.0.8: Destination host unreachable. Ping statistics for 172.26.100.x: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), I have the VPN remote host address of 80.75.67.x, which shows me as being connected. But i'm unsure if there is a config issue at the server side or my end that has caused this issue? I have had some recent Win7 (automatic) updates, but it's hard to tell if that's caused this problem. This is my output from arp: C:\Users\cmorton>arp -a Interface: 192.168.0.8 --- 0xe Internet Address Physical Address Type 192.168.0.1 00-18-4d-b9-68-5e dynami 192.168.0.6 00-f4-b9-68-0c-9a dynami 192.168.0.7 08-00-27-f2-9f-d6 dynami 192.168.0.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.251 01-00-5e-00-00-fb static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 192.168.56.1 --- 0x15 Internet Address Physical Address Type 192.168.56.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.251 01-00-5e-00-00-fb static 224.0.0.252 01-00-5e-00-00-fc static 255.255.255.255 ff-ff-ff-ff-ff-ff static

    Read the article

  • Small office network setups

    - by user39822
    I work at a small office and we're overhauling our network setup there. We're a web dev company and at the moment we have 50+ production sites running on the same machine that runs our internal email, which is just plain stupid. We're moving all our client hosting off site and are now looking for something to run our internal office requirement. Below is a brain dump: Equal amount of Mac & PC, about 25 machines in total. We need a central "server" to host files that should be accessible everyone as a "network drive". If possible we'd like to use low cost hardware for this (Mac or Win based). Disk space should be upward of 1TB. Ideally we should also be able to run a small web server on this machine (LAMP stack) to run some planning and billing applications we wrote ourselves. We need some sort of MS Exchange alternative for things like a shared calendar and especially being able to set Out of Office replies. We have one printer that is connected to the network Setup should be something can preferably be managed easily via a graphical interface and NOT require command line skills. Users want to keep using Apple Mail or MS Outlook After a quick google I came across the Zimbra collaboration suite, can anyone recommend this or any other solution for our office?

    Read the article

  • Client can't reach my production webserver. It's their ISP's fault, but now what?

    - by MikeN
    I have a customer in Michigan who can't access my production SaaS webserver that is hosted on Slicehost. All other companies across the US/Canada/Europe have no problem reaching the site. This problem is occuring intermittantly, and Slicehost customer service says it's a problem with the client's ISP. I got the IP address of my client, and ping'ing that IP address from my PROD server fails, but ping'ing the IP address from my dev box or our seperate blog server (also hosted on slicehost) works. How do I debug a problem like this? I asked the client to reach out to their local ISP and ask about this problem. A traceroute shows that the packets are getting stopped on a Comcast Michigan node which is the client's ISP. Is there anything I can do additionally to fix this problem for my client?

    Read the article

  • ovs-vsctl: "eth0" is not a valid UUID

    - by Przemek Lach
    I'm trying to setup an open v-switch inside my Ubuntu 12.04 Server VM. I have created three interfaces for this VM and I want to create a port mirror inside of the VM using these there interfaces and open v-switch. There are three Host-Only Adapters: eth0, eth1, eth2. The idea is that three other VM's will be connected to these adapters. One of these VM's will stream UDP video to eth0 and I want the vswitch'd VM to mirror those packets from eth0 onto eth1 and eth2. Each of the VM's connected to eth1 and eth2 will get the same video stream. I performed the following steps to install open v-switch: $ apt-get install python-simplejson python-qt4 python-twisted-conch automake autoconf gcc uml-utilities libtool build-essential $ apt-get install build-essential autoconf automake pkg-config $ wget http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ tar xf http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ cd http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ apt-get install libssl-dev iproute tcpdump linux-headers-`uname -r` $ ./boot.sh $ ./configure - -with-linux=/lib/modules/`uname -r`/build $ make $ sudo make install After installation I configured as follows: $ insmod datapath/linux/openvswitch.ko $ sudo touch /usr/local/etc/ovs-vswitchd.conf $ mkdir -p /usr/local/etc/openvswitch $ ovsdb-tool create /usr/local/etc/openvswitch/conf.db Then I started the server: $ ovsdb-server /usr/local/etc/openvswitch/conf.db \ --remote=punix:/usr/local/var/run/openvswitch/db.sock \ --remote=db:Open_vSwitch,manager_options \ --private-key=db:SSL,private_key \ --certificate=db:SSL,certificate \ --bootstrap-ca-cert=db:SSL,ca_cert --pidfile --detach --log-file $ ovs-vsctl –no-wait init (run only once) $ ovs-vswitchd --pidfile --detach The above steps I got from this tutorial and it all worked fine. I then proceeded to add a port mirror based on the open v-switch documentation under Port Mirroring. I successfully completed the following commands: $ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 eth1 $ ovs-vsctl add-port br0 eth2 $ ifconfig eth0 promisc up $ ifconfig eth1 promisc up $ ifconfig eth2 promisc up At this point when I run ovs-vsctl show I get the following: 75bda8c2-b870-438b-9115-e36288ea1cd8 Bridge "br0" Port "br0" Interface "br0" type: internal Port "eth0" Interface "eth0" Port "eth2" Interface "eth2" Port "eth1" Interface "eth1" And when I run ifconfig I get the following: eth0 Link encap:Ethernet HWaddr 08:00:27:9f:51:ca inet6 addr: fe80::a00:27ff:fe9f:51ca/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth1 Link encap:Ethernet HWaddr 08:00:27:53:02:d4 inet6 addr: fe80::a00:27ff:fe53:2d4/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth2 Link encap:Ethernet HWaddr 08:00:27:cb:a5:93 inet6 addr: fe80::a00:27ff:fecb:a593/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth3 Link encap:Ethernet HWaddr 08:00:27:df:bb:d8 inet addr:192.168.1.139 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fedf:bbd8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2211 errors:0 dropped:0 overruns:0 frame:0 TX packets:1196 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:182987 (182.9 KB) TX bytes:125441 (125.4 KB) NOTE: I use eth3 as a bridge adapter for SSH'ing into the VM. So now, I think I've done everything correctly but when I try to create the bridge using the following command: $ ovs-vsctl -- set Bridge br0 mirrors=@m -- --id=@eth0 get Port eth0 -- --id=@eth1 get Port eth1 -- --id=@m create Mirror name=app1Mirror select-dst-port=eth0 select-src-port=@eth0 output-port=@eth1,eth2 I get the following error: ovs-vsctl: "eth0" is not a valid UUID I don't understand why it's not able to find the interfaces?

    Read the article

  • Can't route specific subnet thru VPN in ubuntu

    - by Disco
    I'm having issues routing traffic thru VPN. Here's my setup I have 3 hosts, let's call them A, B and Z B and Z have a VPN connection in the 10.10.10.x SUBNET A and B have a direct connection in the 10.10.12.x SUBNET I want to be able to route traffic from A to Z, like : A <= 10.10.12.254 [LAN] 10.10.12.111 => B <= 10.10.10.152 [VPN] 10.10.10.10 => Z On host B, i have set up ip_forwarding : net.ipv4.ip_forward = 1 and routing on host B: [root@hostA: ~]# ip route 10.10.10.10 dev ppp0 proto kernel scope link src 10.10.10.152 10.10.12.0/24 dev eth1 proto kernel scope link src 10.10.12.111 10.10.10.0/24 dev ppp0 scope link 169.254.0.0/16 dev eth1 scope link routing on host A: [root@hostA: ~]# ip route 10.10.10.0 via 10.10.12.111 dev eth1 10.10.12.0/24 dev eth1 proto kernel scope link src 10.10.12.254 169.254.0.0/16 dev eth1 scope link default via 192.168.1.1 dev eth0 But still not able to ping 10.10.10.10 from host A. Any idea ? I'm pulling my hairs out.

    Read the article

  • how do I set up a virtual host (it's not working, and I've done everything right)

    - by piratepartypumpkin
    My router redirects port 80 to port 8080. My router works fine and my domain name is routed properly. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

    Read the article

  • Windows Server 2003 port forwarding

    - by Vitor Braga
    Using the "netsh interface portproxy" I added a port forwarding to a Windows Server 2k3. The command "netsh interface portproxy show all" shows the added forwarding. On the other hand, any client connecting to the incoming port will receive a "connection refused" message. netstat also doesn't show the incoming port as listening. The machine firewall is disabled. There is any other way to setup port forwarding on Windows or debugging tips?

    Read the article

  • isolate web servers on intranet with dfl-800

    - by microchasm
    I administer a small network (10 users). I'm getting ready to deploy a internal webapp that will be hosted and accessed locally only. There are about 10 users on the network (192.168.111.0/24), a win2k3 server, apache (RHEL), and Mysql (RHEL), and various miscellaneous peripheries. I'd like to isolate the apache and sql boxes into a seperate area of the lan to keep things easier to maintain/grow. I've been reading about vlans, subnets, etc.. I'm not clear, however, which would be the best solution for our setup. Thanks for any tips and or advice.

    Read the article

  • ipv6 with KVM on debian

    - by Eliasdx
    I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

    Read the article

  • Distribute outgoing connections among multiple IPs configured on the same NIC

    - by cedivad
    I have a NIC with 2 aliases on it. The network interface has 3 IPs configured on it. Think about it like this: i can ping the same server by hitting .100 .101 and .102. I want the source address of the outgoing connections to be distributed among these ip. So if i have 3 opened connections, one connection will have result as having an IP address ending with .100, the other two should result as having as ip addresses .101 and .102. I'm using FreeBSD but I think this question to be Linux-Like wide.

    Read the article

  • Need to detect the same application open on another computer on the network. Any software around tha

    - by Joe Schmoe
    I have a time management application that I use at home quite a lot and have running most of the time. At home, I have a desktop PC and a couple of laptops scattered around the house...all networked together. Unfortunately, the application I use is not multi-user and I risk losing/corrupting data if it has been left running on one computer inadvertently while I start using it on another one in another part of the house. I use Live Mesh to automatically keep the application's database synced across the different computers and I just need some way of making sure that I don't start using the application on another computer before closing it down on the previous one. Anyone know of any Windows software that can detect if an application is running simultaneously on different computers on my network, and warn me if I am about to have two open at the same time?

    Read the article

  • Should I limit end-user gigabit ports to avoid saturating uplink/trunk connections?

    - by Joel Coel
    We have a campus with 16 buildings and older 850nm 1Gbps fiber links between the buildings, that all come to a core switch for our servers that also uses 1Gbps ports. We're finally starting to replace our aging 10/100 end-user switches, and much of what we're looking at are 1 Gbps units. My question is, since the trunk/uplink lines are still 1Gbps, if I were to install 1 Gbps switches for end users, should I limit the ports to 100Mbps until I can also upgrade the trunks to avoid allowing a bad-behaving host to saturate a trunk line (since we're a college, we have plenty of mis-behaving hosts) and thereby create a DoS situation for a building, or will TCP congestion control typically take care of that for me? What if we have a lot of UDP traffic (games, video chats, even a small amount of bittorrent)?

    Read the article

  • Add a netbook to an existing Windows XP home network

    - by GorillaSandwich
    I've got a home network set up with a couple of Windows XP computers. I'm now trying to add our new netbook to it - also running XP. (The goal is to share files and a printer.) I have run the Network Setup Wizard and made sure that the workgroup name is the same as the others, and have rebooted several times, but whenever I try to 'view workgroup computers,' the only one on it is the netbook. I have a Windows XP CD, but the netbook has no drive. The wizard has some options for floppy disks, but that's useless to me these days. What is this wizard actually trying to do, and can I do it manually? Surely it can't be this hard.

    Read the article

  • TCPDump and IPTables DROP by string

    - by Tiffany Walker
    by using tcpdump -nlASX -s 0 -vvv port 80 I get something like: 14:58:55.121160 IP (tos 0x0, ttl 64, id 49764, offset 0, flags [DF], proto TCP (6), length 1480) 206.72.206.58.http > 2.187.196.7.4624: Flags [.], cksum 0x6900 (incorrect -> 0xcd18), seq 1672149449:1672150889, ack 4202197968, win 15340, length 1440 0x0000: 4500 05c8 c264 4000 4006 0f86 ce48 ce3a E....d@[email protected].: 0x0010: 02bb c407 0050 1210 63aa f9c9 fa78 73d0 .....P..c....xs. 0x0020: 5010 3bec 6900 0000 0f29 95cc fac4 2854 P.;.i....)....(T 0x0030: c0e7 3384 e89a 74fa 8d8c a069 f93f fc40 ..3...t....i.?.@ 0x0040: 1561 af61 1cf3 0d9c 3460 aa23 0b54 aac0 .a.a....4`.#.T.. 0x0050: 5090 ced1 b7bf 8857 c476 e1c0 8814 81ed P......W.v...... 0x0060: 9e85 87e8 d693 b637 bd3a 56ef c5fa 77e8 .......7.:V...w. 0x0070: 3035 743a 283e 89c7 ced8 c7c1 cff9 6ca3 05t:(>........l. 0x0080: 5f3f 0162 ebf1 419e c410 7180 7cd0 29e1 _?.b..A...q.|.). 0x0090: fec9 c708 0f01 9b2f a96b 20fe b95a 31cf ......./.k...Z1. 0x00a0: 8166 3612 bac9 4e8d 7087 4974 0063 1270 .f6...N.p.It.c.p What do I pull to use IPTables to block via string. Or is there a better way to block attacks that have something in common? Question is: Can I pick any piece from that IP packet and call it a string? iptables -A INPUT -m string --alog bm --string attack_string -j DROP In other words: In some cases I can ban with TTL=xxx and use that should an attack have the same TTL. Sure it will block some legit packets but if it means keeping the box up it works till the attack goes away but I would like to LEARN how to FIND other common things in a packet to block with IPTables

    Read the article

  • Keep source IP after NAT

    - by John Miller
    Until today I used a cheapy router so I can share my internet connection and keep a webserver online too, while using NAT. Users IP ($_SERVER['REMOTE_ADDR']) was fine, I was seeing class A IPs of users. But as traffic grown up everyday, I had to install a Linux Server (Debian) to share my Internet Connection, because my old router couldn't keep the traffic anymore. I shared the internet via IPTABLES using NAT, but now, after forwarding port 80 to my webserver, now instead of seeing real users IP, I see my Gateway IP (Linux Internal IP) as any user IP Address. How to solve this issue? I edited my post, so I can paste the rules I'm currently using. #!/bin/sh #I made a script to set the rules #I flush everything here. iptables --flush iptables --table nat --flush iptables --delete-chain iptables --table nat --delete-chain iptables -F iptables -X # I drop everything as a general rule, but this is disabled under testing # iptables -P INPUT DROP # iptables -P OUTPUT DROP # these are the loopback rules iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # here I set the SSH port rules, so I can connect to my server iptables -A INPUT -p tcp --sport 513:65535 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 --dport 513:65535 -m state --state ESTABLISHED -j ACCEPT # These are the forwards for 80 port iptables -t nat -A PREROUTING -p tcp -s 0/0 -d xx.xx.xx.xx --dport 80 -j DNAT --to 192.168.42.3:80 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p tcp -s 192.168.42.3 --sport 80 -j ACCEPT # These are the forwards for bind/dns iptables -t nat -A PREROUTING -p udp -s 0/0 -d xx.xx.xx.xx --dport 53 -j DNAT --to 192.168.42.3:53 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p udp -s 192.168.42.3 --sport 53 -j ACCEPT # And these are the rules so I can share my internet connection iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0:1 -j ACCEPT If I delete the MASQUERADE part, I see my real IP while echoing it with PHP, but I don't have internet. How to do, to have internet and see my real IP while ports are forwarded too? ** xx.xx.xx.xx - is my public IP. I hid it for security reasons.

    Read the article

  • How do I set up a bridge on Ubuntu GNOME 14.04

    - by NJRandy
    I found a guide for setting up a bridge in Fedora and was trying this: $ nmcli connection delete p33p1 $ nmcli connection add con-name br0 type bridge ifname br0 autoconnect yes $ nmcli connection add con-name p33p1 type bridge-slave ifname p33p1 master br0 autoconnect yes I found that $ nmcli con delete uuid [uuid here] accomplished the first step. nmcli connection does not have an 'add' action in this distribution. Please help me do the 2nd and 3rd steps. Context: I am trying to set up a virtual machine. I believe this is a necessary step for the VM to access my network and the internet. Please feel free to correct me if I am wrong! BTW, I am a linux newbie, tech oldie. Thank you.

    Read the article

  • How to play WAV file through Network Paging Interface

    - by BGM
    In our building we have a Viking Paging ZPI-4 Interface for our intercom. The interface receives data from our Asterisk Phone system via a Cisco SPA112 Port Adapter which has it's own IP address on the network and converts digital into analog. Asterisk plays the "5" tone and then allows the user's voice to commence over the connection. Now, what I want to do is to play a wav file over this Viking Paging device using the Cisco Port Adapter. I know how to get Asterisk to do it, but I want to do this without Asterisk. I want some kind of program that can talk to the Cisco Port Adapter and then transmit the wav file into the Viking Paging Device. What kind of program do I need to get or make? Now, I found this link if it helps anyone with ideas. I also found this information, but I'm not sure how to apply it. I also found this, but it involves an arduino. However, I already have the analog-to-digital convertor, and the Viking will handle sending sound over the paging speakers. I just need to know how to send the wav file to the Viking via the Port Adapter. So far, I know my wav file should be formatted as 8bit mono, and I need to send the "5" tone to open the Viking Pager's channel. [update] I am trying to figure out if I can use VLC player to stream to the ipaddress of the Port Adapter. So far I'm not having success with that, and don't even know if it will work. Windows Media Player has a streaming option too. I am thinking that since the Cisco Port Adapter thinks it is a sort of phone, that the only way this can be done is via SIP.

    Read the article

  • Routing application traffic through specific interface

    - by UnicornsAndRainbows
    Hello All! First question here, so please go easy: I have a debian linux 5.0 server with two public interfaces. I would like to route outbound traffic from one instance of an application via one interface and the second instance through the second interface. There are some challenges: both instances of the application use the same protocol both instances of the application can access the entire internet (can't route based on dest network) I can't change the code of the application I don't think a typical approach to load balancing all traffic is going to work well, because there are relatively few destination servers being accessed in the outbound traffic, and all traffic would really need to be distributed pretty evenly across these relatively few servers. I could probably run two virtualized servers on the box and bind each of them to a different external ip, but I'm looking for a simpler solution, maybe using iproute or iptables? Any ideas for me? Thanks in advance - and I'm happy to answer any questions.

    Read the article

  • Windows Vista: TCP/IP stack is smashed, how to reinstall the LAN-Devices?

    - by Ice
    the TCP/IP stack is smashed, thats why no LAN-Connections are running. I want to download the LAN drivers from another computer and uninstall and reinstall the LAN devices on this system. Hopefully that should recreate the stack. But what to download? What uninstall? How to install? Windows Vista is protected against such changes, so how to achieve that job? please help. Update per 2011-03-11: I found all the tipps and hints about "TCP/IP Repair, LSP Fix, and WinSock Fix" according to windows vista but nothing helped to bring back network access. What can i do as next step or which opportunities are left?

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >