Search Results

Search found 27258 results on 1091 pages for 'installed programs'.

Page 205/1091 | < Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >

• Install MegaCli to Monitor Perc 5/i in Nexentastor 3

  - by Peter Valadez

  I have a Dell 2950 with a Perc 5/i Raid controller that we've already installed Nexentastor 3 Community Edition on. We setup a raid-10 array that and put a ZFS pool on top of the hardware. As I understand, in this configuration ZFS/Nexentastor will not be able to tell when a disk fails in the array. Obviously, this is not optimal. Since the Dell Perc 5/i controller is a rebranded LSI controller, you should be able to use the MegaCli utility to manage the array and monitor its condition. I had seen in a separate forum that the Perc 5/i is very similar to the LSI MegaRAID 8480E, so I tried installing the MegaCli utility at the link below. However, I have not been able to successfully install the utility. http://www.lsi.com/support/products/Pages/MegaRAIDSAS8480E.aspx Here is what happened when I tried to install MegaCli: root@Nexenta2:/files# pkgadd -d MegaCli.pkg Warning: unable to relocate '$BASEDIR' mv: cannot move `solmegacli-8.02.16/' to a subdirectory of itself, `solmegacli-8.02.16//var/lib/dpkg/alien/solmegacli/reloc/solmegacli-8.02.16' mv: cannot move `solmegacli-8.02.16/' to a subdirectory of itself, `solmegacli-8.02.16//opt/solmegacli-8.02.16' 822-date: warning: This program is deprecated. Please use 'date -R' instead. 822-date: warning: This program is deprecated. Please use 'date -R' instead. solmegacli_8.02.16-1_all.deb generated (Reading database ... 41397 files and directories currently installed.) Preparing to replace solmegacli 8.02.16-1 (using solmegacli_8.02.16-1_all.deb) ... Unpacking replacement solmegacli ... Setting up solmegacli (8.02.16-1) ... In /var/logs/dpkg.log: 2012-03-23 20:40:19 status unpacked solmegacli 8.02.16-1 2012-03-23 20:40:19 configure solmegacli 8.02.16-1 8.02.16-1 2012-03-23 20:40:19 status unpacked solmegacli 8.02.16-1 2012-03-23 20:40:19 status half-configured solmegacli 8.02.16-1 2012-03-23 20:40:19 status installed solmegacli 8.02.16-1 So... I've got three questions: Is it possible to install and use MegaCli in Nexentastor 3? If so, how can I install MegaCli on Nexentastor 3? Suggestions welcome!!! If not, is there a better way to monitor the condition of the Perc 5/i hardware raid? Our 2950 does have a DRAC card, so can I use that to monitor the raid condition?

  Read the article

• Installing a php extension (xdiff) from pecl on Linux

  - by wilsonsilva

  I was getting this error on my php script: Fatal error: Call to undefined function xdiff_file_diff() I realised that I didn't had the xdiff extension installed. When I tried to install it using the install pecl xdiff command, I got this errors (among other lines): configure: WARNING: You will need re2c 0.13.4 or later if you want to regenerate PHP configure: error: Please reinstall the libxdiff distribution Then I installed re2c and libxdiff: wget http://www.compdigitec.com/labs/files/re2c_0135_redhat.rpm wget ftp://ftp.task.gda.pl/vol/vol1/ftp.pld-linux.org/dists/2.0/PLD/i386/PLD/RPMS/libxdiff-0.7-1.i386.rpm rpm -ivh re2c_0135_redhat.rpm rpm -ivh libxdiff-0.7-1.i386 But after that I still get the same errors. PS: I've Googled a LOT and I found a couple of people with this problem but they didn't get an answer either :(

  Read the article

• Wireless not working - HP Probook 4540s

  - by Oguzhan

  I just installed Ubuntu 12.04 on 3 HP Probook 4540s's, and none of them seems to be able to connect to wireless networks. I have 1 Probook 4540s with Windows 7 installed and I can access wlan from it. I tried installing the necessary drivers from HP's website, but it still doesn't seem to be working. I've seen other people with different Probooks having similar problems, but their computers seem to be able to detect and even attempt to connect wlans, while mine doesn't even acknowledge that it has wireless. Any help would be appreciated. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Thames [Radeon 7500M/7600M Series] 03:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 30) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 30) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 30) 04:00.0 Network controller: Ralink corp. Device 3290 04:00.1 Bluetooth: Ralink corp. Device 3298 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07)

  Read the article

• puppet rspec no such file to load -- rspec-puppet (LoadError)

  - by Vorsprung

  I have no prior experience at all of ruby. I am not interested in ruby (and so have no knowledge of rails etc) as such but am using puppet to manage a group of servers. I have written some modules and the rspec-puppet system looks like it would be very useful. However, I cannot get rspec-puppet to work I am using Ubuntu LTS 10.04 I have installed puppet rspec using the directions on their web page What I actually did apt-get install rubygems # (installs 1.8) gem install rspec-expectations gem install rspec-puppet I also installed librspec-ruby1.8 Then I ran rspec-puppet-init in a puppet module directory I'd already made (it's a working puppet module) I made a file as defined in the tutorial $ more spec/defines/rule_spec.rb require 'spec_helper' describe 'vanusers::rule' do let(:title) { 't1' } it { should contain_class('vanusers::JamieA') } end but when I try and run it there is a mysterious dependancy issue $ spec spec/defines/rule_spec.rb /home/jamie/git/puppet/modules/vanusers/spec/spec_helper.rb:1:in `require': no such file to load -- rspec-puppet (LoadError) from /home/jamie/git/puppet/modules/vanusers/spec/spec_helper.rb:1 from ./spec/defines/rule_spec.rb:1:in `require' from ./spec/defines/rule_spec.rb:1 from /usr/lib/ruby/1.8/spec/runner/example_group_runner.rb:15:in `load' from /usr/lib/ruby/1.8/spec/runner/example_group_runner.rb:15:in `load_files' from /usr/lib/ruby/1.8/spec/runner/example_group_runner.rb:14:in `each' from /usr/lib/ruby/1.8/spec/runner/example_group_runner.rb:14:in `load_files' from /usr/lib/ruby/1.8/spec/runner/options.rb:132:in `run_examples' from /usr/lib/ruby/1.8/spec/runner/command_line.rb:9:in `run' from /usr/bin/spec:3 Here is the solution I came up with in the end:: apt-get install rubygems gem install rspec-expectations rspec-puppet puppet-lint puppetlabs_spec_helper so your path picks up the gem stuff export PATH=/var/lib/gems/1.8/bin:$PATH cd into module and rm spec/spec_helper.rb rspec-puppet-init replace Rakefile with require 'rake' require 'rspec/core/rake_task' require 'puppetlabs_spec_helper/rake_tasks' Then "rake spec" to run tests or "rake lint" to check files http://sysadvent.blogspot.co.uk/2013/12/day-22-getting-started-testing-your.html was an excellent source of info

  Read the article

• Ubuntu 12.04 LTS Wireless Asus USB-N53 (rt3572sta) driver installation issue

  - by Jake Thompson

  My purchase of the Asus USB-N53 just came in today and I spent several hours Googling and researching drivers for this device. When I first plugged the device in it connected fine to my open system, WEP, DHCP configured access point. I opened Google Chrome and a few pages loaded, everything seemed fine. 30 seconds later... Boom! It disconnected and showed attempts to reconnect and asked for the WEP key and just showed a state of infinite connection time until it asked me for the password again. I'm using amd64 (64 bit Ubuntu desktop 12.04 LTS) The official driver can be found here although I had no luck with it. lsusb: Bus 003 Device 002: ID 0b05:179d ASUSTek Computer, Inc. uname -a Linux Jake 3.2.0-31-generic #50-Ubuntu SMP Fri Sep 7 16:16:45 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ----------------------------------------------------------------------------------Solved: I must of done something wrong when I originally installed the latest drivers from the chipset manufacturers website. I tried reinstalling and did modprobe rt3572sta and waited maybe 10 minutes??? and I connected then I rebooted and everything seems to be working so far. What I did do before hand is unplug the device and typed into the terminal (once for every source I attempted to install): cd '<directory of the driver source>' make uninstall make clean Then I went into the 2.5.0.0 directory and installed that with make make install Then I typed modprobe rt3572sta This was all in superuser. For those who don't know: sudo su

  Read the article

• Cannot access Network Shares on Windows Server 2008 running VisualSVN Server

  - by mwillmott

  Hi, I have installed VisualSVN server on Windows Server 2008. The server is part of a domain but not the domain controller, it is just a data server and now an SVN server. VisualSVN uses port 80 and can only be access from inside the network (i do i by going to the dns name of the server). However, ever since i have installed this, other computers on the network can no longer access the shared folders on the server EXCEPT the domain controller which has no problems accessing the shares. I am stumped, i am guessing it is something to do with Apache running and not using host-headers (or whatever the Apache equivalent may be) but just being bound to the servers DNS name or IP. Any suggestions?

  Read the article

• Sql Server 2008 - Cannot connect to local default instance

  - by Tone

  I recently rebuilt my machine to Windows 7 x64, installed Sql Server 2008 enterprise. I can connect fine to other remote instances via Management Studio (be they 2000, 2005 or 2008), but i cannot find my local default instance. I have verified that a directory was created for the default instance C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER I can connect to SQLEXPRESS instance fine I have rerun setup to ensure I have everything installed I have verified that the SQLSERVER(MSSQLSERVER) service is running I have tried brownsing for the instance and see all the others available except my local one I have tried using this for servername: TSOUTHERLANDPC\MSSQLSERVER, the first part being my local machine name My issue is not the same as this post or this post. Any ideas?

  Read the article

• Make bootable iso with grub chainloading

  - by hlovdal

  My parents' pc has windows 7's boot manager installed at MBR and grub2 is installed on /dev/sda2 (booting linux on /dev/sda2). I want to make a bootable cd so that when booted from it just chainloads into the boot manager on the second partition. I assume using grub rather than grub2 for this will be simpler, using the configuration timeout=0 hiddenmenu default=0 title grub2 (/dev/sda2) rootnoverify (hd0,1) chainloader (hd0,1)+1 I know I can make a bootable linux cd in various ways, but that is not what I want. I just want to put grub/grub2 on the cd, no kernels or programs. The question is how do I make the iso file? I have found some references to installing on a floppy or usb disk, but all those assume the device is present when running the grub install commands. A iso file is different.

  Read the article

• Random touchpad and keyboard freezes on new installation

  - by ancaleth

  My touchpad and keyboard freeze up on my newly installed Ubuntu 10.10. They remain frozen until you shut down manually. No keys work, cursor doesn't move - it's like a screenshot. I was using Ubuntu 10.4 via wubi before on this Laptop where this problem never occurred. (I did not migrate wubi or upgrade to 10.10, it's a fresh start. 64-bit on Dell Studio, plenty of RAM, plenty of free space on partition etc.) I can't say there is a pattern yet, once it happened during the download of packages with the Update Manager, once it was just using Firefox, no other program running. In between these crashes the laptop was booted once, updates were installed etc., firefox was used and there weren't any problems. Both crashes should be in the attached kern.log and I noticed there were some error problems before the last crash (at the end, obviously). It seems the wireless was experiencing problems. This wasn't noticed on the user end, since the touchpad + keyboard were already frozen. kern.log: http://paste.ubuntu.com/552617/ How can the freezes be fixed? Edit: I will try Ctrl+Alt+F1 and then Ctrl+Alt+F7 when next freeze occurs, to see if it works again after this, as suggested here. But the keyboard seemed pretty frozen to me.

  Read the article

• Getting Started with Employee Info Starter Kit (v4.0.0)

  - by Mohammad Ashraful Alam

  The new release of Employee Info Starter Kit contains lots of exciting features available in Visual Studio 2010 and .NET 4.0. To get started with the new version, you will need less than 5 minutes. Minimum System Requirements Before getting started, please make sure you have installed Visual Studio 2010 RC (or higher) and Sql Server 2005 Express edition (or higher installed on your machine. Running the Starter Kit for First Time 1. Download the starter kit 4.0.0 version form here and extract it. 2. Go to <extraction folder>\Source\Eisk.Solution and click the solution file 3. From the solution explorer, right click the “Eisk.Web” web site project node and select “Set as Startup Project” and hit Ctrl + F5   4. You will be prompted to install database, just follow the instruction. That’s it! You are ready to use this starter kit. Running the Tests Employee Info Starter Kit contains a infrastructure for Integration and Unit Testing, by utilizing cool test tools in Visual Studio 2010. Once you complete the steps, mentioned above, take a minute to run the test cases on the fly. 1. From the solution explorer, to go “Solution Items\e-i-s-k-2010.vsmdi” and click it. You will see the available Tests in the Visual Studio Test Lists. Select all, except the “Load Tests” node (since Load Tests takes a bit time) 2. Click “Run Checked Tests” control from the upper left corner. You will see the tests running and finally the status of the tests, which indicates the current health of you application from different scenarios. Technorati Tags: asp.net,architecture,starter kit,employee info starter kit,visual studio 2010,.net 4.0,entity framework

  Read the article

• Getting Started with Employee Info Starter Kit (v4.0.0)

  - by joycsharp

  The new release of Employee Info Starter Kit contains lots of exciting features available in Visual Studio 2010 and .NET 4.0. To get started with the new version, you will need less than 5 minutes. Minimum System Requirements Before getting started, please make sure you have installed Visual Studio 2010 RC (or higher) and Sql Server 2005 Express edition (or higher installed on your machine. Running the Starter Kit for First Time 1. Download the starter kit 4.0.0 version form here and extract it. 2. Go to <extraction folder>\Source\Eisk.Solution and click the solution file 3. From the solution explorer, right click the “Eisk.Web” web site project node and select “Set as Startup Project” and hit Ctrl + F5   4. You will be prompted to install database, just follow the instruction. That’s it! You are ready to use this starter kit. Running the Tests Employee Info Starter Kit contains a infrastructure for Integration and Unit Testing, by utilizing cool test tools in Visual Studio 2010. Once you complete the steps, mentioned above, take a minute to run the test cases on the fly. 1. From the solution explorer, to go “Solution Items\e-i-s-k-2010.vsmdi” and click it. You will see the available Tests in the Visual Studio Test Lists. Select all, except the “Load Tests” node (since Load Tests takes a bit time) 2. Click “Run Checked Tests” control from the upper left corner. You will see the tests running and finally the status of the tests, which indicates the current health of you application from different scenarios. Technorati Tags: asp.net,architecture,starter kit,employee info starter kit,visual studio 2010,.net 4.0,entity framework

  Read the article

• dual boot xp/xp, now win7/xp getting no xp

  - by ped

  I have a laptop on which I have two drives with separate XP installs, one barebones for music production, the other "normal" XP with Office etc. (Unfortunately the bios won't give a boot disk choice) Normally I would be presented with two WinXPs on booting. Selecting the second one would get me into the "normal installation on disk 1 (C).Selecting the first in boot order would give me D: (disk 2) withe barebones XP. However, I installed Windows 7 Home onto disk 1 (C:), but there were no dual boot options anymore, even though I installed DualBoot Pro and added WinXP disk D:. The options now show show up, but seletcing Win XP just turns into a reboot back to where I started. Any help would be much appreciated

  Read the article

• Remote Desktop Connection - Connection Failed

  - by NLV

  Let me explain the problem. My system is connected to a network and 'was' having XP installed in it. Recently i formatted the system and installed windows server 2003 and added the machine to the network. Everything is working fine like mapping the network drives, pinging the machines etc. But i've the following problems. I'm not able to do a remote desktop connection to another system in the network. Some systems in the network is able to do a remote desktop to my machine. But not all. If i host any web service in my system i'm not able to connect it from any other machine in the network. I've already configured the Remote Desktop to accept connections. Any ideas? NLV

  Read the article

• How to fix “Module ndiswrapper not found"

  - by jason328

  I have Ubuntu 12.10 and whenever I run sudo modprobe ndiswrapper, I get the following error. FATAL: Module ndiswrapper not found. The command dkms status returns with... ndiswrapper, 1.57, 3.2.0-32-generic, i686: installed The make.log in ndiswrapper returns with... DKMS make.log for ndiswrapper-1.57 for kernel 3.5.0-18-generic (i686) Wed Nov 7 22:16:12 EST 2012 make -C /usr/src/linux-headers-3.5.0-18-generic M=/var/lib/dkms/ndiswrapper /1.57/build make[1]: Entering directory `/usr/src/linux-headers-3.5.0-18-generic' LD /var/lib/dkms/ndiswrapper/1.57/build/built-in.o MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/crt_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/hal_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/ndis_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/ntoskernel_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/ntoskernel_io_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/rtl_exports.h MKEXPORT /var/lib/dkms/ndiswrapper/1.57/build/usb_exports.h CC [M] /var/lib/dkms/ndiswrapper/1.57/build/crt.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/hal.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/iw_ndis.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/loader.o CC [M] /var/lib/dkms/ndiswrapper/1.57/build/ndis.o /var/lib/dkms/ndiswrapper/1.57/build/ndis.c: In function ‘NdisGetCurrentProcessorCounts’: /var/lib/dkms/ndiswrapper/1.57/build/ndis.c:2657:24: error: ‘struct kernel_stat’ has no member named ‘cpustat’ /var/lib/dkms/ndiswrapper/1.57/build/ndis.c:2658:31: error: ‘struct kernel_stat’ has no member named ‘cpustat’ /var/lib/dkms/ndiswrapper/1.57/build/ndis.c:2659:17: error: ‘struct kernel_stat’ has no member named ‘cpustat’ make[2]: *** [/var/lib/dkms/ndiswrapper/1.57/build/ndis.o] Error 1 make[1]: *** [_module_/var/lib/dkms/ndiswrapper/1.57/build] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-18-generic' make: *** [modules] Error 2 I have installed commons, utils-1.9, dkms, source but it's still returning this error. How do I fix this?

  Read the article

• How to install Grub2 under several common scenarios

  - by Huckle

  I feel the community has long needed a clean guide on how to install Grub2 under a a few extremely common scenarios. I will accept answer as solved when it has one section per scenario and assumes nothing other than what is specified. Please add to the existing answer, wiki style, keeping to the original assumptions. Rules: 1. You cannot, at any point in the answer, invoke Ubiquity (the Ubuntu installer). 2. I strongly recommend not using any automatic boor-repair tools as they're not very educational Scenario 1: Non-booting Linux OS, No boot partition, Fix from Live CD Setup: /dev/sda1 is formatted ext* /dev/sda2 is formatted linux_swap /dev/sda1 doesn't boot because MBR is scrambled and /boot/* was erased Explain: How to boot to a Live CD / USB and restore Grub2 to the MBR and /boot of /dev/sda1 Scenario 2: Non-booting Linux OS, Boot partition, Fix from Live CD Setup: /dev/sda1 is formatted fat /dev/sda2 is formatted ext* /dev/sda3 is formatted linux_swap /dev/sda2 doesn't boot because the MBR is scrambled and /dev/sda1 was formatted Explain: How to boot to a Live CD / USB and restore Grub2 to the MBR and /dev/sda1 and then update the fstab on /dev/sda2 Scenario 3: Install on to thumb drive, Booting various OSes, From Linux OS Setup: /dev/sdb is removable media /dev/sdb1 is formatted fat /dev/sdb2 is formatted ext* /dev/sdb3 is formatted fat The MBR of /dev/sdb is otherwise not initialized You are executing from a Linux based OS installed on /dev/sda Explain: How to install Grub2 on to /dev/sdb1, mark /dev/sdb1 active, be able to chose between /dev/sdb2 and /dev/sdb3 on boot. Scenario 4: (Bonus) Install on to thumb drive, Booting ISO, From Linux OS Setup: /dev/sdb is removable media /dev/sdb1 is formatted fat /dev/sdb1 contains /iso/live.iso /dev/sdb2 is formatted ext* /dev/sdb3 is formatted fat The MBR of /dev/sdb is otherwise not initialized You are executing from a Linux based OS installed on /dev/sda Explain: How to install Grub2 on to /dev/sdb1, mark /dev/sdb1 active, be able to chose between /dev/sdb2, /dev/sdb3, and /iso/live.iso on boot.

  Read the article

• [MISC GEEKERY] Support for Some Versions of Windows is Ending

  - by Matthew Guay

  Are you sticking with your older version of Windows instead of upgrading to Windows 7?  There’s no problem with that, but here’s a quick reminder to make sure you’re running the latest service pack to stay protected. Microsoft offers security updates and more throughout the lifetime of a version of Windows, and periodically they roll all the latest updates and improvements together into a service pack.  After a while, only computers running the latest service pack will still get updates to keep them safe. Recently, Microsoft has been warning that support is ending for Windows XP with Service Pack 2 and the release version of Windows Vista.  When support ends, you will not receive any new security updates for Windows.  You can continue to use your computer the same as before, but it may not be as secure and if new security issues are discovered they will not be updated. However, it’s easy to stay supported: simply install XP Service Pack 3 or Vista Service Pack 2, depending on your computer.  Here’s how to do that: Windows XP To install Windows XP Service Pack 3, you can either check Windows Update for updates, or simply download it from Microsoft at this link: Download XP Service Pack 3 Run the download (or if you’re updating from Windows Update the installer will automatically launch), and proceed just as you normally would when installing a program.  Your computer will have to reboot during the install, so make sure you’ve saved all your work and closed other programs before installing.   To check what service pack your computer is running, click Start, then right-click on the My Computer button and choose Properties. This will show you what version and service pack of Windows you are running, and in this screenshot we see this computer has be updated to Service Pack 3. Please Note:  The version of XP shipped with Windows XP Mode in Windows 7 comes preconfigured with Service Pack 3, and does not need updated.  Additionally, if your computer is running the 64 bit version of Windows XP, then Service Pack 2 is the latest service pack for your computer, and it is still supported. Windows Vista If your computer is running Windows Vista, you can install Service Pack 2 to stay up to date and supported.  Simply check Windows Update for Service Pack 2 if you haven’t installed it yet, or download the installer for your computer from the link below: 32 bit: Vista Service Pack 2 32-bit 64 bit: Vista Service Pack 2 64-bit Run the installer, and simply set it up as a normal program installation.  Do note that your computer will reboot during the installation, so make sure to save your work and close other programs before installing. To see what service pack your computer is running, click the Start orb, then right-click on the Computer button and select Properties. This will show what service pack and edition of Windows Vista your computer is running right at the top of the page. Conclusion Microsoft makes it easy to keep using your computer safely and securely even if you choose to keep using your older version of Windows.  By installing the latest service pack, you will make sure that your computer will be supported for years to come.  Windows 7 users, you don’t need to worry; no service has been released for it yet.  Stay tuned, and we’ll let you know when any new service packs are available. www.microsoft.com/EOS – End of Support Information from Microsoft Similar Articles Productive Geek Tips Remove Optional and Probably Unnecessary Windows Vista ComponentsRequesting Hotfixes from Microsoft the Easy WayUnderstanding Windows Vista Aero Glass RequirementsAdd Network Support to Windows Live MovieMakerCustomize the Manufacturer Support Info in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional OutSync will Sync Photos of your Friends on Facebook and Outlook Windows 7 Easter Theme YoWindoW, a real time weather screensaver Optimize your computer the Microsoft way Stormpulse provides slick, real time weather data Geek Parents – Did you try Parental Controls in Windows 7?

  Read the article

• Queued Loadtest to remove Concurrency issues using Shared Data Service in OpenScript

  - by stefan.thieme(at)oracle.com

  Queued Processing to remove Concurrency issues in Loadtest ScriptsSome scripts act on information returned by the server, e.g. act on first item in the returned list of pending tasks/actions. This may lead to concurrency issues if the virtual users simulated in a load test scenario are not synchronized in some way.As the load test cases should be carried out in a comparable and straight forward manner simply cancel a transaction in case a collision occurs is clearly not an option. In case you increase the number of virtual users this approach would lead to a high number of requests for the early steps in your transaction (e.g. login, retrieve list of action points, assign an action point to the virtual user) but later steps would be rarely visited successfully or at all, depending on the application logic.A way to tackle this problem is to enqueue the virtual users in a Shared Data Service queue. Only the first virtual user in this queue will be allowed to carry out the critical steps (retrieve list of action points, assign an action point to the virtual user) in your transaction at any one time.Once a virtual user has passed the critical path it will dequeue himself from the head of the queue and continue with his actions. This does theoretically allow virtual users to run in parallel all steps of the transaction which are not part of the critical path.In practice it has been seen this is rarely the case, though it does not allow adding more than N users to perform a transaction without causing delays due to virtual users waiting in the queue. N being the time of the total transaction divided by the sum of the time of all critical steps in this transaction.While this problem can be circumvented by allowing multiple queues to act on individual segments of the list of actions, e.g. per country filter, ends with 0..9 filter, etc.This would require additional handling of these additional queues of slots for the virtual users at the head of the queue in order to maintain the mutually exclusive access to the first element in the list returned by the server at any one time of the load test. Such an improved handling of multiple queues and/or multiple slots is above the subject of this paper.Shared Data Services Pre-RequisitesStart WebLogic Server to host Shared Data ServicesYou will have to make sure that your WebLogic server is installed and started. Shared Data Services may not work if you installed only the minimal installation package for OpenScript. If however you installed the default package including OLT and OTM, you may follow the instructions below to start and verify WebLogic installation.To start the WebLogic Server deployed underneath of Oracle Load Testing and/or Oracle Test Manager you can go to your Start menu, Oracle Application Testing Suite and select the Restart Oracle Application Testing Suite Application Service entry from the Tools submenu.To verify the service has been started you can run the Microsoft Management Console for Services by Selecting Run from the Start Menu and entering services.msc. Look for the entry that reads Oracle Application Testing Suite Application Service, once it has changed it status from Starting to Started you can proceed to verify the login. Please note that this may take several minutes, I would say up to 10 minutes depending on the strength of your CPU horse-power.Verify WebLogic Server user credentialsYou will have to make sure that your WebLogic Server is installed and started. Next open the Oracle WebLogic Server Adminstration Console on http://localhost:8088/console.It may take a while until the application is deployed and started. It may display the following until the Administration Console has been deployed on the fly.Afterwards you can login using the username oats and the password that you selected during install time for your Application Testing Suite administrative purposes.This will bring up the Home page of you WebLogic Server. You have actually verified that you are able to login with these credentials already. However if you want to check the details, navigate to Security Realms, myrealm, Users and Groups tab.Here you could add users to your WebLogic Server which could be used in the later steps. Details on the Groups required for such a custom user to work are exceeding this quick overview and have to be selected with the WebLogic Server Adminstration Guide in mind.Shared Data Services pre-requisites for Load testingOpenScript Preferences have to be set to enable Encryption and provide a default Shared Data Service Connection for Playback.These are pre-requisites you want to use for load testing with Shared Data Services.Please note that the usage of the Connection Parameters (individual directive in the script) for Shared Data Services did not playback reliably in the current version 9.20.0370 of Oracle Load Testing (OLT) and encryption of credentials still seemed to be mandatory as well.General Encryption settingsSelect OpenScript Preferences from the View menu and navigate to the General, Encryption entry in the tree on the left. Select the Encrypt script data option from the list and enter the same password that you used for securing your WebLogic Server Administration Console.Enable global shared data access credentialsSelect OpenScript Preferences from the View menu and navigate to the Playback, Shared Data entry in the tree on the left. Enable the global shared data access credentials and enter the Address, User name and Password determined for your WebLogic Server to host Shared Data Services.Please note, that you may want to replace the localhost in Address with the hosts realname in case you plan to run load tests with Loadtest Agents running on remote systems.Queued Processing of TransactionsEnable Shared Data Services Module in Script PropertiesThe Shared Data Services Module has to be enabled for each Script that wants to employ the Shared Data Service Queue functionality in OpenScript. It can be enabled under the Script menu selecting Script Properties. On the Script Properties Dialog select the Modules section and check Shared Data to enable Shared Data Service Module for your script. Checking the Shared Data Services option will effectively add a line to your script code that adds the sharedData ScriptService to your script class of IteratingVUserScript.@ScriptService oracle.oats.scripting.modules.sharedData.api.SharedDataService sharedData;Record your scriptRecord your script as usual and then add the following things for Queue handling in the Initialize code block, before the first step and after the last step of your critical path and in the Finalize code block.The java code to be added at individual locations is explained in the following sections in full detail.Create a Shared Data Queue in InitializeTo create a Shared Data Queue go to the Java view of your script and enter the following statements to the initialize() code block.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);This will create an instantiation of the Shared Data Queue object named queueA which is maintained for upto 120 minutes.If you want to use the code for multiple scripts, make sure to use a different queue name for each one here and in the subsequent steps. You may even consider to use a dynamic queueName based on filters of your result list being concurrently accessed.Prepare a unique id for each IterationIn order to keep track of individual virtual users in our queue we need to create a unique identifier from the virtual user id and the used username right after retrieving the next record from our databank file.getDatabank("Usernames").getNextDatabankRecord();getVariables().set("usernameValue1","VU_{{@vuid}}_{{@iterationnum}}_{{db.Usernames.Username}}_{{@timestamp}}_{{@random(10000)}}");String usernameValue = getVariables().get("usernameValue1");info("Now running virtual user " + usernameValue);As you can see from the above code block, we have set the OpenScript variable usernameValue1 to VU_{{@vuid}}_{{@iterationnum}}_{{db.Usernames.Username}}_{{@timestamp}}_{{@random(10000)}} which is a concatenation of the virtual user id and the iterationnumber for general uniqueness; as well as the username from our databank, the timestamp and a random number for making it further unique and ease spotting of errors.Not all of these fields are actually required to make it really unique, but adding the queue name may also be considered to help troubleshoot multiple queues.The value is then retrieved with the getVariables.get() method call and assigned to the usernameValue String used throughout the script.Please note that moving the getDatabank("Usernames").getNextDatabankRecord(); call to the initialize block was later considered to remove concurrency of multiple virtual users running with the same userid and therefor accessing the same "My Inbox" in step 6. This will effectively give each virtual user a userid from the databank file. Make sure you have enough userids to remove this second hurdle.Enqueue and attend Queue before Critical PathTo maintain the right order of virtual users being allowed into the critical path of the transaction the following pseudo step has to be added in front of the first critical step. In the case of this example this is right in front of the step where we retrieve the list of actions from which we select the first to be assigned to us.beginStep("[0] Waiting in the Queue", 0);{info("Enqueued virtual user " + usernameValue + " at the end of queueA");sharedData.offerLast("queueA", usernameValue);info("Wait until the user is the first in queueA");String queueValue1 = null;do {// we wait for at least 0.7 seconds before we check the head of the// queue. This is the time it takes one user to move through the// critical path, i.e. pass steps [5] Enter country and [6] Assign// to meThread.sleep(700);queueValue1 = (String) sharedData.peekFirst("queueA");info("The first user in queueA is currently: '" + queueValue1 + "' " + queueValue1.getClass() + " length " + queueValue1.length() );info("The current user is '"+ usernameValue + "' " + usernameValue.getClass() + " length " + usernameValue.length() + ": indexOf " + usernameValue.indexOf(queueValue1) + " equals " + usernameValue.equals(queueValue1) );} while ( queueValue1.indexOf(usernameValue) < 0 );info("Now the user is the first in queueA");}endStep();This will enqueue the username to the tail of our Queue. It will will wait for at least 700 milliseconds, the time it takes for one user to exit the critical path and then compare the head of our queue with it's username. This last step will be repeated while the two are not equal (indexOf less than zero). If they are equal the indexOf will yield a value of zero or larger and we will perform the critical steps.Dequeue after Critical PathAfter the virtual user has left the critical path and complete its last step the following code block needs to dequeue the virtual user. In the case of our example this is right after the action has been actually assigned to the virtual user. This will allow the next virtual user to retrieve the list of actions still available and in turn let him make his selection/assignment.info("Get and remove the current user from the head of queueA");String pollValue1 = (String) sharedData.pollFirst("queueA");The current user is removed from the head of the queue. The next one will now be able to match his username against the head of the queue.Clear and Destroy Queue for FinishWhen the script has completed, it should clear and destroy the queue. This code block can be put in the finish block of your script and/or in a separate script in order to clear and remove the queue in case you have spotted an error or want to reset the queue for some reason.info("Clear queueA");sharedData.clearQueue("queueA");info("Destroy queueA");sharedData.destroyQueue("queueA");The users waiting in queueA are cleared and the queue is destroyed. If you have scripts still executing they will be caught in a loop.I found it better to maintain a separate Reset Queue script which contained only the following code in the initialize() block. I use to call this script to make sure the queue is cleared in between multiple Loadtest runs. This script could also even be added as the first in a larger scenario, which would execute it only once at very start of the Loadtest and make sure the queues do not contain any stale entries.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);info("Clear queueA");sharedData.clearQueue("queueA");This will create a Shared Data Queue instance of queueA and clear all entries from this queue.Monitoring QueueWhile creating the scripts it was useful to monitor the contents, i.e. the current first user in the Queue. The following code block will make sure the Shared Data Queue is accessible in the initialize() block.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);In the run() block the following code will continuously monitor the first element of the Queue and write an informational message with the current username Value to the Result window.info("Monitor the first users in queueA");String queueValue1 = null;do {queueValue1 = (String) sharedData.peekFirst("queueA");if (queueValue1 != null)info("The first user in queueA is currently: '" + queueValue1 + "' " + queueValue1.getClass() + " length " + queueValue1.length() );} while ( true );This script can be run from OpenScript parallel to a loadtest performed by the Oracle Load Test.However it is not recommend to run this in a production loadtest as the performance impact is unknown. Accessing the Queue's head with the peekFirst() method has been reported with about 2 seconds response time by both OpenScript and OTL. It is advised to log a Service Request to see if this could be lowered in future releases of Application Testing Suite, as the pollFirst() and even offerLast() writing to the tail of the Queue usually returned after an average 0.1 seconds.Debugging QueueWhile debugging the scripts the following was useful to remove single entries from its head, i.e. the current first user in the Queue. The following code block will make sure the Shared Data Queue is accessible in the initialize() block.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);In the run() block the following code will remove the first element of the Queue and write an informational message with the current username Value to the Result window.info("Get and remove the current user from the head of queueA");String pollValue1 = (String) sharedData.pollFirst("queueA");info("The first user in queueA was currently: '" + pollValue1 + "' " + pollValue1.getClass() + " length " + pollValue1.length() );ReferencesOracle Functional Testing OpenScript User's Guide Version 9.20 [E15488-05]Chapter 17 Using the Shared Data Modulehttp://download.oracle.com/otn/nt/apptesting/oats-docs-9.21.0030.zipOracle Fusion Middleware Oracle WebLogic Server Administration Console Online Help 11g Release 1 (10.3.4) [E13952-04]Administration Console Online Help - Manage users and groupshttp://download.oracle.com/docs/cd/E17904_01/apirefs.1111/e13952/taskhelp/security/ManageUsersAndGroups.htm

  Read the article

• How to install Windows 7 onto software RAID-0

  - by Jay B

  I recently got a new laptop (Asus G73JH-A2) which has two identical hard drives in it. Unfortunately the motherboard does not have a RAID controller. What I would like to do is run the drives in a RAID-0 configuration to improve performance (plus get the extra capacity on one partition). I would like Windows installed onto the striped volume (RAID 0). I have spent some time using diskpart to create a striped volume across the two drives, however when I go to install windows and select the volume it will not let me select 'Next' giving the error "Windows cannot be installed to this hard disk space. The partition contains one or more dynamic volumes that are not supported for installation." I'm hoping theres a step that I am missing that will allow me to install windows on a striped volume. Any ideas?

  Read the article

• Issue with gpg agent in Ubuntu 12.04 after installing gnome3 shell

  - by Jeroen

  I just did a fresh install of Ubuntu 12.04. Initially things were working. But after I installed some software, the 'gpg agent' is unresponsive. I suspect it has something to do with upgrades that I downloaded from the gnome 3 ppa. When I try to sign a package, it terminates with: gpg: problem with the agent - disabling agent use debsign: gpg error occurred! Aborting.... debuild: fatal error at line 1271: running debsign failed The GPG gui tool (called "Passwords and Keys" or seahorse) isn't starting anymore either. When I click it, it tries to start and then gives up and dies after a couple of seconds. I am not sure where to look for log files of gpg agent. The only thing that I see in /var/log is in auth.log that says: May 1 20:04:14 jeroen-ubuntu gnome-keyring-daemon[1997]: couldn't create prompt for gnupg passphrase: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.keyring.SystemPrompter was not provided by any .service files Not sure if it is related, but when I try to start seahorse from the command line, I get: jeroen@jeroen-ubuntu:~$ seahorse (seahorse:4828): GLib-GIO-ERROR **: Settings schema 'org.gnome.crypto.pgp' is not installed Edit: I fixed the seahorse GUI by manually downloading and reinstalling gnome-keyring version from precise instead of the ppa. However, I still cannot sign packages.

  Read the article

• Remove Dell Openmanage from Windows 2008

  - by Erwin Blonk

  I have installed Dell Openmanage Server Agent 4.2.2 on Windows Server 2008. I need the newer version, so I need to install this version first. However, outside some registry references pointing to sources that aren't there, there is little or no trace of it being installed. For example, no trace of the program files or an entry in Prgrams And Features. Still, installing a newer version keeps coming up with an older version that needs to be removed first. When I try to install version 4.2.2 to repair and eventually remove it, it gives an error: Dell Openmanage Server Agent - Error An error was encountered while testing machine type. Failure openingen required handle to .DLL. Dell Openmanage Server Agent cannot continue the installation. Setup will exit now. I haven't found anything using different parts of the error messages as search terms.

  Read the article

• CodePlex Daily Summary for Friday, December 17, 2010

  CodePlex Daily Summary for Friday, December 17, 2010Popular ReleasesVCC: Latest build, v2.1.31217.1: Automatic drop of latest buildBCrypt.Net: BCrypt.Net R4: Fixed a integer overflow at workFactor = 31LiveChat Starter Kit: LCSK v1.0: This is a working version of the LCSK for Visual Studio 2010, ASP.NET MVC 3 (using Razor View Engine). this is still provider based (with 1 provider Sql) and this is still using WebService and Windows Forms operator console. The solution is cleaner, with an installer to create tables etc. Let me know your feedbackOrchard Project: Orchard 0.9: Orchard Release Notes Build: 0.9.253 Published: 12/16/2010 How to Install OrchardTo install the Orchard tech preview using Web PI, follow these instructions: http://www.orchardproject.net/docs/Installing-Orchard-Using-Web-PI.ashx Web PI will detect your hardware environment and install the application. --OR-- Alternatively, to install the release manually, download the Orchard.Web.0.9.253.zip file. The zip contents are pre-built and ready-to-run. Simply extract the contents of the Orch...SharpDropBox Client for .NET: WP7 SharpDropBox Client - 0.1 Technology Preview: I decided to go ahead and release this. It works well for simple browsing folder structure/downloading files (and login works). See samples for an example of how to use it. I am in progress with a couple other methods which aren't currently working.SQL Monitor: SQL Monitor 2.9: 1. automatically set sql for new query if a object is selected(table/sp/function/view)SplendidCRM: SplendidCRM 5.0 Community Edition: SplendidCRM Software has adopted the GNU Affero General Public License Version 3 (AGPLv3) for its Community Edition. This release includes the full set of SQL source code in the Community Edition, something that was previously only available in the Professional and Enterprise Editions. An article on the subject of Commercial Open-Source licensing has been posted at http://www.codeproject.com/KB/architecture/splendid-guide-article6.aspx.DotSpatial: DotSpatial 12-15-2010: This release contains a few minor bug fixes and hopefully the GDAL libraries for the 3.5 x86 build actually built to the correct directory this time.DotNetNuke® Community Edition: 05.06.01 Beta: This is the initial Beta of DotNetNuke 5.6.1. See the DotNetNuke Roadmap a full list of changes in this release.MSBuild Extension Pack: December 2010: Release Blog Post The MSBuild Extension Pack December 2010 release provides a collection of over 380 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GU...Access Control Service Samples and Documentation (Labs): Samples-R3: Contains latest ACS samples (corresponding to R3 release) that show how to integrate ACS with web services, ASP.NET websites (Web Forms and MVC) and on how to interact with the ACS Management Service. The Readmes for these samples are available here.TweetSharp: TweetSharp v2.0.0.0 - Preview 5: Documentation for this release may be found at http://tweetsharp.codeplex.com/wikipage?title=UserGuide&referringTitle=Documentation. Note: This code is currently preview quality. Preview 5 ChangesMaintenance release with user reported fixes Preview 4 ChangesReintroduced fluent interface support via satellite assembly Added entities support, entity segmentation, and ITweetable/ITweeter interfaces for client development Numerous fixes reported by preview users Preview 3 ChangesNumerous ...EnhSim: EnhSim 2.2.2 ALPHA: 2.2.2 ALPHAThis release adds in the changes for 4.03a at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - The spirit ...Silverlight Contrib: Silverlight Contrib 2010.1.0: 2010.1.0 New FeaturesCompatibility Release for Silverlight 4 and Visual Studio 2010FlickrNet API Library: 3.1.4000: Newest release. Now contains dedicated Windows Phone 7 DLL as well as all previous DLLs. Also contains Windows Help file documentation now as standard.mojoPortal: 2.3.5.8: see release notes on mojoportal.com http://www.mojoportal.com/mojoportal-2358-released.aspx Note that we have separate deployment packages for .NET 3.5 and .NET 4.0 The deployment package downloads on this page are pre-compiled and ready for production deployment, they contain no C# source code. To download the source code see the Source Code Tab I recommend getting the latest source code using TortoiseHG, you can get the source code corresponding to this release here.Microsoft All-In-One Code Framework: Visual Studio 2010 Code Samples 2010-12-13: Code samples for Visual Studio 2010SuperWebSocket: SuperWebSocket Drop 2: Changes: based on SuperSocket 1.3 supported sub protocol supported SSL/TLS encryption (wss) in Sync socket mode fixed some data communication bugsWii Backup Fusion: Wii Backup Fusion 0.9 Beta: - Aqua or brushed metal style for Mac OS X - Shows selection count beside ID - Game list selection mode via settings - Compare Files <-> WBFS game lists - Verify game images/DVD/WBFS - WIT command line for log (via settings) - Cancel possibility for loading games process - Progress infos while loading games - Localization for dates - UTF-8 support - Shortcuts added - View game infos in browser - Transfer infos for log - All transfer routines rewritten - Extract image from image/WBFS - Support....NETTER Code Starter Pack: v1.0.beta: '.NETTER Code Starter Pack ' contains a gallery of Visual Studio 2010 solutions leveraging latest and new technologies and frameworks based on Microsoft .NET Framework. Each Visual Studio solution included here is focused to provide a very simple starting point for cutting edge development technologies and framework, using well known Northwind database (for database driven scenarios). The current release of this project includes starter samples for the following technologies: ASP.NET Dynamic...New ProjectsaoleFilter: This is a Filter by MagicshuiChocottone: Simple to-do listData Access Engine (DAE): Data Access Engine (DAE) is an open source and free .NET component to access all popular DBMSs such as Microsoft SQL Server, MySQL, Oracle, Microsoft Access, SQLite and databases that connected by ODBC. DAE helps to connect different DBMSs at the same time. DependencyEvaluation: Programmatically sort your objects based on dependencies. Would work as a compiler framework, project planning, data binding, etc.Doc2Text Converter: A converter that can convert document files(like .doc,.ppt,and .pdf) to plain text.Dynamics AX Test Runner for Visual Studio 2010: Invoke Dynamics AX Test cases from within Visual Studio 2010 and retrieve the results.ExtensibleExtensions: Pack of extensions, firstly text utilities like pluralize, capitalize will be included.FluentHttp: .NET fluent api wrapper for creating restful web requests.K:L:O:N:K Updater Service: The K:L:O:N:K Updater Service is a deployment tool which can be used to deploy Microsoft Installer (msi ), zip or other file formats. A directory is setup to be the deployment directory. Put files into this directory and the packages are distributed and installed at clients.Keyki: my code repositoryLED Editor: Simple project for editing a LED sequence ...Maui: SchedulerMcAfee Vulnerability Manager - Delta Report: Processes two .CSV files generated by McAfee Vulnerability Manager to highlight which vulnerabilities were patched or are still outstanding.milkway Project: A java web project under Spring. Galaxy is an enterprise wiki system.Minecraft Save Wizard: Do you like minecraft ? Do you like it so much that you wish there were more worlds ? Well now you can have as many worlds as you desire. Simply move them to and from your saves folder to a backup folder using this software. It couldn't be simpler ;)Minis Manager: A manager for miniature figures to use for rpgs etc.Model2Form: An ASP.NET Control similar to GridView but it auto builds a Web From in run-time by binding a Model. OBD C# Wrapper: OBD C# Wrapper I want to help peaople to get data from an OBD system. The idea is to create a C# class with preconfigured methods for load values and for use them in a GUI. With this class people have to focalized on the GUI design and not on the interface with OBD.Opalis Extension Local Group and User Management: A Opalis Integration pack allowing for management of local computer groups and users.Opalis Integration Pack: VMWare VSphere: An integration Pack for Opalis. Extending Opalis to integrate fully with VMWare. Built using the Vmware Powershell CMDLets wrapped in C#.Opalis Utilities: An integration pack for Opalis. Extending Opalis to provide some addition UtilitiesOrchard Maps: A Maps module for OrchardOur ICProject: IC 2011 projectpatterns & practices: Project Silk: Project Silk provides guidance and sample implementations that describe and illustrate recommended practices for building next generation web applications using web technologies like HTML5, jQuery, CSS3 and IE9. pianduan: ????pob: xna game in developmentpscommand Firefox Extension: A Firefox extension which allows user to invoke PowerShell commands on links.R.NET: R.NET enables .NET Framework to collaborate with R statistical computing. R.NET requires .NET Framework 4 and R.dll. You already have the DLL in the `bin' folder if you installed R environment, and you need no other extra installations. R.NET is developed in C#.Rough Set tool set: Rough Set Tool SetSerial Port Terminal (SPTerm): Serial Port Terminal (SPTerm) is used for basic communication using serial port (com). Sending bytes and ASCII from PC can be done using SPTerm. It is useful for micro controller projects for UART and simple transmission. Hex data can be sent out directly from text box in SPTermSLGame: NullThe Jumping Point: TJP is a 2 player sidescroller based on SFML. TJP is developed in C++ and will be available for both linux and windows.UIT CRM: Ð? án môn h?c Qu?n lý d? án CNTT c?a nhóm. (tru?ng ÐH CNTT - ÐHQG TpHCM)

  Read the article

• Firewall behind firewall

  - by Makach

  I've recently changed jobs and I've been set up with a new workstation. On all previous places where I've been working they've had some sort of local firewall installed on each and every workstation - but here I've been told not to activate it because it is not necessary since we're already behind a HW Firewall. To me this seem a bit naïve, but I cannot emphasise it. I always thought a local firewall was good practice, ie. if something managed to come through the hw firewall there might be a slight chance other computers on the lan would block the internal threath. We got free access to internet and we got a virus checker installed.

  Read the article

• using RHEL5 as a router

  - by gopikrishna7779

  Dear Sir, I am planning to use a RHEL5 installed computer as a internet connection sharing device. I mean I want to share the internet connection through it I have installed 2 Lan cards in it eth0 and eth1 eth0 Internet eth1 LAN eth0 configuration as follows ; Ipaddress : 115.252.64.187 Subnet : 255.255.255.240 Gateway : 115.252.64.177 I wrote the following entries in Vim /etc/resolv.conf nameserver 202.138.96.2 (preferred DNS Server) nameserver 202.138.103.2 (secondary DNS server) :q! then eth1 ipaddress : 192.168.1.1 subnet : 255.255.255.0 gateway : 192.168.1.1 (I am confused which gateway I need to use in the above scenario) I am unable to ping to my lan and I am able to connect to the Internet. Please let me know the sollution for this. Thanks in advance. regards, G.Gopi Krishna

  Read the article

• How can I open urls on my host machine with VMWARE?

  - by Yanamon

  I am running a Windows 7 vm with WMware player from Fedora. I have VMWare tools installed successfully and I have successfully some of it's features like Unity mode so it seems to be installed correctly. That being said I still cannot get urls to open up in my host machine's browsers, these are the steps I have taken: Within the vm I set "Default Host Application" to be the application to open urls. Within my host machine I have set Chrome to be my preferred application for opening urls. Enabled Shared Folders in the vm (Not sure if that really helped anything but I saw it suggested on a forum post) After doing that when I click on a link I get the following error message: Default host Application: Make sure the virtual machine's configuration allows the guest to open host applications. I cannot find any option like that in my vm's configuration so I am not sure what the error message is referring to.

  Read the article

• Windows Server 2008 R2 LDAPS

  - by Chad Moran

  I have a Server 2008 R2 server with ADDS installed. I'm trying to configure HP's ILO utility to connect to it over SSL. I installed the Active Directory Certificate Service, after doing so I'm still not able to connect to LDAP over SSL. I checked the event log and it's showing warnings with Event ID 36886 saying that there aren't default credentials yet. I'm not too sure why this is happening. I haven't done anything with ADCS other than installing the service do I need to create a certificate for the server?

  Read the article

< Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >