Search Results

Search found 7024 results on 281 pages for 'usb modem'.

Page 215/281 | < Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >

  • Network MP600 printer asking me to install new driver on laptop.

    - by user15003
    I have windows 7 home 32-bit on my desktop which is connected to my mp600 via USB. I have Vista 64-bit on my laptop. The MP600 is set for sharing and appears under printers in network under my pc's name. When I click on connect it says "The server for canon inkjet mp600 printer does not have the correct printer drivers installed........." I don't know what to do and it is really frustrating. It all worked fine before when I had XP 32 bit on my desktop

    Read the article

  • Ubuntu not showing disk

    - by ojek
    I have a laptop which had broken windows 7 installed on it. I created a ubuntu live usb and tried installing ubuntu over that win7. After a few minutes, I got an error message, so I needed to restart the computer. Now the laptop says that there is no bootable device - reasonable message given that there was an error during linux installation. But: Bios can see my hard drive, When I start ubuntu in live mode, and try either sudo fdisk -l or gparted, it doesn't show any hard disk drives. I am 90% sure that hdd is broken, but it is wierd that bios can see it, and ubuntu doesn't. How can I be 100% sure about that hdd? Is there any additional way of detecting my hdd from ubuntu?

    Read the article

  • Is "DSLAM congestion" a legitimate reason for slow DSL?

    - by Jay Bazuzi
    My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

    Read the article

  • Cooling Server Closet - No A/C Is Possible

    - by JamesCo
    We're moving into a new office in an old building in London (that's England :) and are walling off a 2m x 1.3m area where the router & telephone equipment currently terminates to use as a server closet. The closet will contain: 2 24-port switches 1 router 1 VSDL modem 1 Dell desktop 1 4-bay NAS 1 HP micro-server 1 UPS Miscellaneous minor telephony boxes. There is no central A/C in the office and there never will be. We can install ducting to the outside quite easily - it's only a couple of metres to the windows, which face a courtyard. My question is whether installing an extractor fan with ducting to the window should be sufficient for cooling? Would an intake fan and intake duct (from the window, too) be required? We don't want to leave a gap in the closet door as that'll let noise out into the office. If we don't have to put a portable A/C unit into the closet, that'd be perfect. The office has about 12 people; London is temperate, average maximum in August is 31 Celsius, 25 Celsius is more typical. The same equipment runs fine in our current office (same building as new office, also no A/C) but it isn't in an enclosed space. I can see us putting say one Dell 2950 tower server into the closet, but no more than that. So, sustained power consumption in the closet would currently be about 800w (I'm guessing); possibly in the future 2kw. The closet will have a ceiling and no windows and be well-insulated. We don't care if the equipment runs hot, so long as it runs and we don't hear it.

    Read the article

  • Why is (free_space + used_space) != total_size in df? [migrated]

    - by Timothy Jones
    I have a ~2TB ext4 USB external disk which is about half full: $ df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sdc 1922860848 927384456 897800668 51% /media/big I'm wondering why the total size (1922860848) isn't the same as Used+Available (1825185124)? From this answer I see that 5% of the disk might be reserved for root, but that would still only take the total used to 1921328166, which is still off. Is it related to some other filesystem overhead? In case it's relevant, lsof -n | grep deleted shows no deleted files on this disk, and there are no other filesystems mounted inside this one.

    Read the article

  • Wired network on computer to wifi

    - by user329592
    I just got myself a wifi capable cell phone, but I dont have a wireless internet at home. I do have a wired unlimited internet connection on my computer, and I wonder whether there is any gadget that I can plug into my computer (maybe at the usb port?) with which I can turn my computer into a wifi access point? I mean, a dongle or something which will enable me to connect my phone to my computer's internet through wi-fi? Also, I dont know anything about networking, so would it be hard for me to set up a secure wifi point? Thank you for reading this question through. Hope I can buy some sort of adapter which is comparitively cheap.

    Read the article

  • Restoring a Ubuntu Linux LVM drive

    - by user848106
    Scenario: I have a hard disk with a bootable sda1 partition and an Linux LVM. I seem to have corrupted the MBR? or Grub? not sure. I know it no longer boots and even with boot-repair and a Ubuntu live usb I was able to restore it. Following a "fix" with boot-repair I get "missing operating system" Can't i just reinstall grub or a new menu.lst? Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0007b68f Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 625141759 312320001 5 Extended /dev/sda5 501760 625141759 312320000 8e Linux LVM

    Read the article

  • ICS as guest in Ubuntu 12.04 host

    - by oshirowanen
    I have installed Android as per this guide as a guess os via VirtualBox: http://www.android-x86.org/documents/virtualboxhowto Using the following ISO: android-x86-4.0-RC1-eeepc.iso But I am unable to connect to the internet from within the android virtual machine. The host OS is Ubuntu 12.04 where the internet works fine. I have internet access via a usb wireless connection to the home router. All this is fine. If I install Ubuntu 12.04 as a guest, where the host is also Ubuntu 12.04. The guest os'es internet works fine out of the box. But for some reason, I can't get the above androids internet to work out of the box as the guest os. Anyone know what I am doing wrong?

    Read the article

  • What's the quickest way to install Windows 7?

    - by SaultDon
    I am wondering what the quickest/fastest way to install Windows 7 would be? I've read that you can make a bootable USB with unetbootin, or load the ISO contents to a separate partition/hard-drive and boot from there to install. Then I seen a method using imagex to copy the files needed onto a new partition which can be booted from directly, it takes ~7 minutes + ~5 min for the initial boot... I haven't tried it yet but would like to know if anyone knows of anything faster? If you could provide some instructions (step by step) would be great! The imagex method provides a good tutorial for example.

    Read the article

  • Why can't I connect to computers on my network using our external IP address?

    - by Kivin
    My home network is serviced by an ADSL line. The modem is in bridged mode. The router performs the PPPoE. Three computers are connected to the router: two wired Windows 7 boxes and a Ubuntu Linux box over wifi. The computers are hosting various forms of services including FTP and HTTP. The router has port forwarding mapped from the relevant ports to the reserved IP addresses for the computers. If I attempt to connect to a server inside the network, such as ftp://67.xx.xxx.xxx from inside the network, the request times out. However if I connect using the internally mapped address, such as ftp://192.168.0.100, all is well. This is a nuisance for setting up software, especially on the laptop which needs to be able to phone home from anywhere, and I just don't have enough expertise with networking to know why this is occurring to even have a clue whether it can be solved or not. edit: It should be noted that the servers can be accessible outside the network - say, at the starbucks across the street - perfectly fine, using the ISP provided address and the appropriate port.

    Read the article

  • How to prevent hard drive from spinning down Windows 7?

    - by JL.
    I had a Western Digital External 1TB drive, which I was accessing via USB. I decided one day, that I would prefer to mount the HDD in my case, and access it via SATA interface. So I took it apart, and the actual mounting was a breeze. The only thing is, I think the device has some default power saving features, which means the device tends to stop spinning when idle for (x) amount of time. This creates delays when I am accessing the HDD. Is there anyway I can turn off these power saving features for this HDD?

    Read the article

  • Windows 8 Restore Problems

    - by Joe
    I created a Windows 8 system image backup on a separate drive before I installed Linux, and during the Linux installation process I accidentally wiped out Windows. I now want to restore my Windows 8 backup that I have on the separate drive. I created a repair USB stick and I followed the directions according to this article. After selecting the image on the hard drive, I get this error: "To restore this computer, Windows needs to format the hard drive." I don't know what this means! The drive partitions are different now then they were when I backup up, so I don't know if that matters. I re-installed Windows and I can restore my files from this backup, but I don't think this covers the registry, etc. I want a full restore. Does anyone know how to fix this problem, or how to restore in a different way? Thanks!

    Read the article

  • Problem linking two Cisco routers with a static route

    - by Chris Kaczor
    I'm trying to link two Cisco routers with a static route and I haven't been able to get it working as expected. Here is the basic setup: Router 1 - WRV210 - 192.168.1.1 - connected to cable modem Router 2 - RV120W - 192.168.2.1 I already have several machines on Router 1 that are working and I want to setup Router 2 with a few other machines on the different subnet. Here is what I've configured: Connected the WAN port on Router 2 to a LAN port on Router 1 Configured Router 1 to give 192.168.1.2 to Router 2 via DHCP Configured Router 1 with a static route (192.168.2.0 mask 255.255.255.0) to 192.168.1.2 using the LAN & Wireless interface Disabled the firewall on Router 2 (since it is covered by Router 1) Configured Router 2 to "Router" mode instead of "NAT" mode Configured Router 2 with a static route (192.168.1.0 mask 255.255.255.0) to 192.168.1.1 using the WAN interface From the research I've done I think that should be enough but things aren't working exactly as expected: Router 2 can ping 192.168.1.1 and 192.168.1.101 (a machine on router 1) A machine on Router 2 can ping 192.168.1.1 and 192.168.1.101 (a machine on router 1) ping 192.168.1.1 and 192.168.1.101 (a machine on router 1) Router 1 can NOT ping 192.168.2.1 or 192.168.2.101 (a machine on router 2) A machine on Router 1 can NOT ping 192.168.2.1 or 192.168.2.101 (a machine on router 2) can NOT ping 192.168.2.1 or 192.168.2.101 (a machine on router 2) Router 1 and a machine on Router 1 can ping 192.168.1.2 (Router 2 itself) I'm confused as to why Router 1 cannot talk to the 192.168.2.0/255.255.255.0 subnet. Any help would be greatly appreciated.

    Read the article

  • How can I share a printer and files on a Windows network over wifi

    - by Jacques
    What is the easiest way to create this setup: WiFi internet router separate in one room. Study room: Laptop with USB printer connected with wifi. My room: Laptop connected with wifi. I want to be able to print from the "My room" laptop to the "Study room" printer, and also share files between them. What is the easiest way to do this? Note, the wireless router needs to be in a separate room for both laptops to be able to connect to it. I've tried configuring homegroups and stuff to do with IP addresses that I found on the internet but have had no success. I'm not an expert with PC's but I've tried hard so there is probably just some trick to do it. If someone can help that will be great.

    Read the article

  • Allow access from outside network with dmz and iptables

    - by Ivan
    I'm having a problem with my home network. So my setup is like this: In my Router (using Ubuntu desktop v11.04), I installed squid proxy as my transparent proxy. So I would like to use dyndns to my home network so I could be access my server from the internet, and also I installed CCTV camera and I would like to enable watching it from internet. The problem is I cannot access it from outside the net. I already set DMZ in my modem to my router ip. My first guess is because i'm using iptables to redirect all inside network to use squid. And not allow from outside traffic to my inside network. Here is my iptables script: #!/bin/sh # squid server IP SQUID_SERVER="192.168.5.1" # Interface connected to Internet INTERNET="eth0" # Interface connected to LAN LAN_IN="eth1" # Squid port SQUID_PORT="3128" # Clean old firewall iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X # Load IPTABLES modules for NAT and IP conntrack support modprobe ip_conntrack modprobe ip_conntrack_ftp # For win xp ftp client #modprobe ip_nat_ftp echo 1 > /proc/sys/net/ipv4/ip_forward # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT ACCEPT # Unlimited access to loop back iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # Allow UDP, DNS and Passive FTP iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT # set this system as a router for Rest of LAN iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT # unlimited access to LAN iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT # DNAT port 80 request comming from LAN systems to squid 3128 ($SQUID_PORT) aka transparent proxy iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT # if it is same system iptables -t nat -A PREROUTING -i $INTERNET -p tcp --dport 80 -j REDIRECT --to-port $SQUID_PORT # DROP everything and Log it iptables -A INPUT -j LOG iptables -A INPUT -j DROP If you know where did I miss, please advice me. Thanks for all your help and I really appreciate it.

    Read the article

  • What keeps you from changing your public IP address and wreak havok?

    - by Whitemage
    An interesting question was asked to me and I did not know what to answer.. So I'll ask here. Let's say I subscribed to an ISP and I'm using cable internet access. ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let's say, 60.61.62.75 and mess with another consumer's internet access? For the sake of this argument, let's say that this other IP address is also owned by the same ISP. Also, let's assume that it's possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gaetway, a network address and a broadcast address. So that's 3 addresses the ISP "loses" to you. That seems very wastefull for dynamically assigned IP addresses where the majority of customers are.. Could they simply be using static arps? ACLs? Other simple mechanisms? Anyone who worked at an ISP would be willing to explain this a bit?

    Read the article

  • How to unmount a VHD in Windows 7. There is no unmount option.

    - by Triynko
    I mounted a VHD file in Windows 7 using the Disk Manager. Once mounted, there is no option to Unmount it. The only thing close to such an option that I can find is if I click the icon in the taskbar notification area that I use to remove USB devices... there's an option to eject the virtual hard disk. However, when I click that, it says that it's in use and cannot be ejected. Even though... it's not in use, I never even browsed the drive. The disk manager is closed... and the only open files handles to the drive (according to disk performance in task manager) is SYSTEM. Ejecting devices cleanly has been a problem since Windows XP, and it sickens me to see it persist into windows 7.

    Read the article

  • Forgot to unmount/eject external hdd, lost moved files. OSX

    - by balupton
    So I was using my mac with my external hard drive connected via USB. I moved about 10gigs of data to it (via drag and drop while holding command to move the files rather than to copy them). They moved to the drive alright, but as I was having some issues and finder crashed after the transfer, I was unable to eject the volume and later everything froze so I had to do a hard restart (hold the power button). When I remounted the volume (plugged the external hdd back in) it no longer had any of the files which I moved onto it. How can I recover these files, as it was a lot of data! Cheers.

    Read the article

  • Speeding up Outlook Express on Windows XP over satellite

    - by John
    My brother is in the field with Doctors Without Borders. I'm posting this question on his behalf. We use outlook express (on a pc running windows XP) and a 9600 baud dial up satellite phone modem to get our email direct from the server in Paris. As this is a very expensive way to communicate (our satellite bill is $50K a year, no joke), it seems like trying to streamline is a good idea. Here's the question- when we connect, the sequence goes: Send outbox mails. This goes pretty quickly, probably 10-15 seconds for each email, up to maybe a couple minutes for an email of 150k or so). The status bar moves pretty quickly, according to the emails sent. The system then says "Checking for new messages on (our account name), and "Receiving list of messages from server". This takes a long time. Like 10-15 minutes. The status bar crawls along. Then it receives the messages. "Receiving messages from server". Again, each message takes 10-15 seconds, and this part moves along reasonably fast. I'm curious as to what is going on in the second part. It takes forever, and doesn't seem to be part of the sending or receiving messages themselves. Is there a way to speed up the process by changing a preference with communicating with the server or something? Does anyone have any advice for him speeding up what Outlooks Express is doing? Obviously his software is ancient and adding more software is not realistic based on the connection speed. Thanks!

    Read the article

  • Multiple IPs on firewall, are these virtual interfaces or what?

    - by Jakobud
    We have 5 static IP addresses from our ISP: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 On our firewall box, the NIC that is connected to our cable modem, appears to have all 5 IP addresses set on it. A previous IT guy set this thing up, and I'm not sure exactly what he did. Are these virtual interfaces on this NIC or what? Here is my ip addr output for that NIC: rwd0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff inet XXX.XXX.XXX.180/24 brd XXX.XXX.XXX.186 scope global rwd0 inet XXX.XXX.XXX.181/29 brd XXX.XXX.XXX.186 scope global rwd0:FWB9 inet XXX.XXX.XXX.182/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB10 inet XXX.XXX.XXX.183/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB11 inet XXX.XXX.XXX.184/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB12 inet6 fe80::250:8bff:fe61:5734/64 scope link valid_lft forever preferred_lft forever I'm a bit new to firewalls and networking so I'm just trying to figure out what he had going on here. I know he used Firewall Builder to configure the iptables rules, maybe that has something to do with the "FWB" I see in those names? So my questions are: What is going on here? Virtual Interfaces? Or something else? If we want to put in a second firewall in parallel with this firewall but we only want it to handle traffic to XXX.XXX.XXX.182, how do we get rid of the static XXX.XXX.XXX.182 address on this existing firewall box?

    Read the article

  • Tool to fix video that's out of sync with audio?

    - by Javier Badia
    I'm looking for (preferably free) software for Windows 7 that will allow me to fix an AVI file that has audio out of sync with the video. I tried with Windows Live Movie Maker and VirtualDub and couldn't find out how to do it (if at all possible) on both of them. If any of those can help me, instructions for that would also be nice. Background: I have a RCA-to-USB capture card, which I'm using to transfer VHS casettes and stuff from a video camera to digital format. The problem is that the audio comes out heavily distorted. So instead I connected the audio out from the VCR directly to the computer's line in. This works, but the audio is out of sync, about half a second behind the video. I could spend time trying to fix this issuee, but I think it'll be easier to simply fix the video.

    Read the article

  • Why can't I route to some sites from my MacBook Pro that I can see from my iPad?

    - by Robert Atkins
    I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

    Read the article

  • How do I export address book from N97

    - by mplungjan
    Hi, I need to copy my numbers from my private Nokia to my office BB. I have not found a way to export my phone numbers from ovi or elsewhere. On Mac iSync stopped working with snow leopard and OVI on windows does not export. I do not mind using a windows suggestion. I lost a description on how to use the ovi backup files in another program. What I have done so far terminal: sudo open -a iSync.app - it launched but iSync said "this device is not supported by iSync" went here http://europe.nokia.com/support/product-support/isync/compatibility-and-download found a plugin (I am sure that was not there a while ago :| ) Checked software version 22.0.110 installed plugin Ran iSync which found and installed my N97 device successfully. synced. It stopped with The connection was lost while talking to the phone. http://discussions.europe.nokia.com/t5/Nseries-and-S60-Smartphones/N97-iSync-Multimedia-Transfer-Modem/m-p/568560 no news since Jan 2010. Tried to download and install http://best-vcard.en.softonic.com/symbian but the installer fails :( I simply do not understand why Nokia is giving us such a hard time. I would not have considered switching from Nokia if Mac had been better supported. It is so frustrating that they just seem not to care losing Nokia fanbois like me - especially since I am this outspoken on the net and what i say on popular forums gets indexed by google fast. I am very close to just go iPhone here. Hope someone has Nokia's ears UPDATE: I Downloaded NbuExplorer from sourceforge. It will extract everything from an OVI backup into VCF, VCS and VMG files. Very useful software and free.

    Read the article

  • Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

    - by Develop7
    Intro I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 Problem But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator screams "Logon failure" upon connect attempt, and, respectively, fails to connect. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d Question So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

    Read the article

  • Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

    - by develop7
    Preface: I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator tells "Logon failure" upon connect attempt. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

    Read the article

< Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >